Vote for min clk frequency for core clks during prepare and enable clocks
at boot sequence. Without this the controller clock runs at very low value
(9.6MHz) which is not sufficient to boot venus.
Signed-off-by: Dikshita Agarwal <dikshita@codeaurora.org>
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Signed-off-by: Stanimir Varbanov <stanimir.varbanov@linaro.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
At this time there is no need to differentiate between the two, we can
reuse the 4xx pm ops callback structure for 6xx.
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Signed-off-by: Stanimir Varbanov <stanimir.varbanov@linaro.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
In various places in the venus codebase we have if (IS_V4()) which takes
the code down paths for 4xx silicon. This logic is broadly applicable to
6xx silicon also. In this patch we add IS_V6() to various IS_V4() decision
locations.
Co-developed-by: Dikshita Agarwal <dikshita@qti.qualcomm.com>
Signed-off-by: Dikshita Agarwal <dikshita@qti.qualcomm.com>
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Signed-off-by: Stanimir Varbanov <stanimir.varbanov@linaro.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
On 6xx we should read wrapper cpu status from the wrapper TZ register set.
Co-developed-by: Jonathan Marek <jonathan@marek.ca>
Signed-off-by: Jonathan Marek <jonathan@marek.ca>
Co-developed-by: Dikshita Agarwal <dikshita@codeaurora.org>
Signed-off-by: Dikshita Agarwal <dikshita@codeaurora.org>
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Signed-off-by: Stanimir Varbanov <stanimir.varbanov@linaro.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
This commit adds 6xx specific interrupt support, some register offsets and
bitmasks differ from 4xx, which we account for in this commit.
[bod: Added commit log. Moved register definition into commit]
Signed-off-by: Dikshita Agarwal <dikshita@codeaurora.org>
Co-developed-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Signed-off-by: Stanimir Varbanov <stanimir.varbanov@linaro.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
This patch adds a 6xx specific boot logic. The goal is to share as much
code as possible between 3xx, 4xx and 6xx silicon.
We need to do a different write to WRAPPER_INTR_MASK with an additional
write to CPU_CS_H2XSOFTINTEN_V6 and CPU_CS_X2RPMh_V6.
The other writes are the same for 6xx and non-6xx silicon albeit at
different absolute relative locations to the base of the venus address
space.
Signed-off-by: Dikshita Agarwal <dikshita@codeaurora.org>
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Signed-off-by: Stanimir Varbanov <stanimir.varbanov@linaro.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
6xx silicon needs to access registers from a AON base address range.
This commit defines the necessary variable for later use.
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Signed-off-by: Stanimir Varbanov <stanimir.varbanov@linaro.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
6xx silicon needs to access registers from a wrapper trust-zone base
address range.
This commit defines the necessary variable for later use.
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Signed-off-by: Stanimir Varbanov <stanimir.varbanov@linaro.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
This commit adds the macro helper IS_V6() which will be used to
differentiate iris2/v6 silicon from previous versions.
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Signed-off-by: Stanimir Varbanov <stanimir.varbanov@linaro.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
This commit defines a range of new base addresses for already defined
blocks.
- CPU_BASE_V6
- CPU_CS_BASE_V6
- CPU_IC_BASE_V6
- WRAPPER_BASE_V6
The base addresses of the blocks are slightly different for 6xx but, aside
from that are layout and bit compatible.
New 6xx specific block addresses will be added in separate commits.
Signed-off-by: Dikshita Agarwal <dikshita@codeaurora.org>
Co-developed-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Signed-off-by: Stanimir Varbanov <stanimir.varbanov@linaro.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
An upcoming silicon change places a number of existing blocks within the
Venus at different relative offsets to the base address of IO region.
In order to handle this difference this patch changes the address offsets
of the registers to function as offsets relative to the relevant sub-block
of registers within the IO region not the base address of the IO region.
As a result of this change venus_readl() and venus_writel() are deleted.
Co-developed-by: Dikshita Agarwal <dikshita@codeaurora.org>
Signed-off-by: Dikshita Agarwal <dikshita@codeaurora.org>
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Signed-off-by: Stanimir Varbanov <stanimir.varbanov@linaro.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
New silicon means that the pre-determined offsets we have been using
in this driver no longer hold. Existing blocks of registers can exist at
different offsets relative to the IO base address.
This commit adds a routine to assign the IO base hooks a subsequent commit
will convert from absolute to relative addressing.
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Signed-off-by: Stanimir Varbanov <stanimir.varbanov@linaro.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The Venus driver has to control two reset signals related to
gcc video_axi0 and videocc mvs0c for v6. Add it.
Signed-off-by: Stanimir Varbanov <stanimir.varbanov@linaro.org>
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Currently hfi_platform_v6.c adds a bunch of capability parameters.
Reviewing downstream we can see a number of these need to be updated.
techpack/video/msm/vidc/msm_vidc_platform.c :: kona_capabilities[]
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Signed-off-by: Stanimir Varbanov <stanimir.varbanov@linaro.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The property is supported from v1 and upwards. So move it to
set_property_1x.
Fixes: 01e869e787 ("media: venus: venc: fix handlig of S_SELECTION and G_SELECTION")
Cc: stable@vger.kernel.org # v5.12
Signed-off-by: Stanimir Varbanov <stanimir.varbanov@linaro.org>
Tested-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
It is observed that on Venus v1 the default header-mode is producing
a bitstream which is not playble. Change the default header-mode to
joined with 1st frame.
Fixes: 002c22bd36 ("media: venus: venc: set inband mode property to FW.")
Cc: stable@vger.kernel.org # v5.12
Signed-off-by: Stanimir Varbanov <stanimir.varbanov@linaro.org>
Tested-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The rate of the core clock is set through devm_pm_opp_set_rate and
to avoid errors from it we have to set the name of the clock via
dev_pm_opp_set_clkname.
Fixes: 9a538b8361 ("media: venus: core: Add support for opp tables/perf voting")
Cc: stable@vger.kernel.org # v5.10+
Signed-off-by: Stanimir Varbanov <stanimir.varbanov@linaro.org>
Tested-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The inst function argument is != NULL only for Venus v1 and
we did not migrate v1 to a hfi_platform abstraction yet. So
check for instance != NULL only after hfi_platform_get returns
no error.
Fixes: e29929266b ("media: venus: Get codecs and capabilities from hfi platform")
Cc: stable@vger.kernel.org # v5.12
Signed-off-by: Stanimir Varbanov <stanimir.varbanov@linaro.org>
Tested-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The Venus v1 behaves differently comparing with the other Venus
version in respect to capability parsing and when they are send
to the driver. So we don't need to initialize hfi parser for
multiple invocations like what we do for > v1 Venus versions.
Fixes: 10865c9898 ("media: venus: parser: Prepare parser for multiple invocations")
Cc: stable@vger.kernel.org # v5.10+
Signed-off-by: Stanimir Varbanov <stanimir.varbanov@linaro.org>
Tested-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Wrong solution of rebase conflict leads to calling twice
v4l2_device_unregister in .venus_remove. Delete the second one.
Signed-off-by: Stanimir Varbanov <stanimir.varbanov@linaro.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Acquire the graph_mutex for traversing the media graph. This seems to have
been missing all the time.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Trivial fixes for many kernel-doc warnings. Most of the comments before
enums or struct can just be that: regular comments.
So just change /** to /*.
In one remaining case it was just a wrong construct: @mem_dev[] -> @mem_dev
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Currently the header argument is being passed by value, so a copy of 256
byte structure on the stack is potentially occurring. Fix this by passing
by reference to avoid any large stack copies.
Addresses-Coverity: ("Big parameter passed by value")
Fixes: 2db16c6ed7 ("media: imx-jpeg: Add V4L2 driver for i.MX8 JPEG Encoder/Decoder")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
In case of error, the function device_link_add() returns NULL
pointer not ERR_PTR(). The IS_ERR() test in the return value
check should be replaced with NULL test.
Fixes: 2db16c6ed7 ("media: imx-jpeg: Add V4L2 driver for i.MX8 JPEG Encoder/Decoder")
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Fix to return negative error code from the error handling
case instead of 0, as done elsewhere in this function.
Fixes: 2db16c6ed7 ("media: imx-jpeg: Add V4L2 driver for i.MX8 JPEG Encoder/Decoder")
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
There is a spelling mistake in a dev_err message. Fix it.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Fixes these kernel-doc warnings:
drivers/media/platform/exynos4-is/fimc-isp.h:139: warning: Function parameter or member 've' not described in 'fimc_is_video'
drivers/media/platform/exynos4-is/fimc-isp.h:139: warning: Function parameter or member 'buf_count' not described in 'fimc_is_video'
drivers/media/platform/exynos4-is/fimc-isp.h:139: warning: Function parameter or member 'buf_mask' not described in 'fimc_is_video'
drivers/media/platform/exynos4-is/fimc-isp.h:139: warning: Function parameter or member 'streaming' not described in 'fimc_is_video'
drivers/media/platform/exynos4-is/fimc-isp.h:139: warning: Function parameter or member 'buffers' not described in 'fimc_is_video'
drivers/media/platform/exynos4-is/fimc-isp.h:139: warning: Function parameter or member 'pixfmt' not described in 'fimc_is_video'
drivers/media/platform/exynos4-is/fimc-isp.h:176: warning: Function parameter or member 'src_fmt' not described in 'fimc_isp'
drivers/media/platform/exynos4-is/fimc-isp.h:176: warning: Function parameter or member 'sink_fmt' not described in 'fimc_isp'
drivers/media/platform/exynos4-is/fimc-isp.h:176: warning: Function parameter or member 'subdev_lock' not described in 'fimc_isp'
drivers/media/platform/exynos4-is/fimc-lite.h:178: warning: Function parameter or member 'events' not described in 'fimc_lite'
drivers/media/platform/exynos4-is/fimc-lite.h:178: warning: Function parameter or member 'streaming' not described in 'fimc_lite'
drivers/media/platform/exynos4-is/media-dev.h:143: warning: Function parameter or member 'wbclk' not described in 'fimc_md'
drivers/media/platform/exynos4-is/media-dev.h:143: warning: Function parameter or member 'fimc_lite' not described in 'fimc_md'
drivers/media/platform/exynos4-is/media-dev.h:143: warning: Function parameter or member 'clk_provider' not described in 'fimc_md'
drivers/media/platform/exynos4-is/media-dev.h:143: warning: Function parameter or member 'subdev_notifier' not described in 'fimc_md'
drivers/media/platform/exynos4-is/media-dev.h:143: warning: Function parameter or member 'pipelines' not described in 'fimc_md'
drivers/media/platform/exynos4-is/media-dev.h:143: warning: Function parameter or member 'link_setup_graph' not described in 'fimc_md'
drivers/media/platform/exynos4-is/fimc-core.h:261: warning: Function parameter or member 'alpha' not described in 'fimc_frame'
drivers/media/platform/exynos4-is/fimc-core.h:321: warning: Function parameter or member 'streaming' not described in 'fimc_vid_cap'
drivers/media/platform/exynos4-is/fimc-core.h:429: warning: Function parameter or member 'drv_data' not described in 'fimc_dev'
drivers/media/platform/exynos4-is/fimc-core.h:495: warning: Function parameter or member 'in_order_1p' not described in 'fimc_ctx'
drivers/media/platform/exynos4-is/fimc-core.h:673: warning: Function parameter or member 'vid_cap' not described in 'fimc_active_queue_add'
drivers/media/platform/exynos4-is/fimc-core.h:685: warning: Function parameter or member 'vid_cap' not described in 'fimc_active_queue_pop'
drivers/media/platform/exynos4-is/fimc-core.h:700: warning: Function parameter or member 'vid_cap' not described in 'fimc_pending_queue_add'
drivers/media/platform/exynos4-is/fimc-core.h:711: warning: Function parameter or member 'vid_cap' not described in 'fimc_pending_queue_pop'
drivers/media/platform/exynos4-is/fimc-reg.h:333: warning: Function parameter or member 'dev' not described in 'fimc_hw_set_dma_seq'
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Fixes these kernel-doc warnings:
drivers/media/platform/exynos-gsc/gsc-core.h:76: warning: Enum value 'GSC_MIXER' not described in enum 'gsc_datapath'
drivers/media/platform/exynos-gsc/gsc-core.h:76: warning: Enum value 'GSC_FIMD' not described in enum 'gsc_datapath'
drivers/media/platform/exynos-gsc/gsc-core.h:76: warning: Excess enum value 'GSC_LOCAL' description in 'gsc_datapath'
drivers/media/platform/exynos-gsc/gsc-core.h:124: warning: Function parameter or member 'color' not described in 'gsc_fmt'
drivers/media/platform/exynos-gsc/gsc-core.h:124: warning: Function parameter or member 'num_comp' not described in 'gsc_fmt'
drivers/media/platform/exynos-gsc/gsc-core.h:297: warning: Function parameter or member 'pix_max' not described in 'gsc_variant'
drivers/media/platform/exynos-gsc/gsc-core.h:297: warning: Function parameter or member 'pix_min' not described in 'gsc_variant'
drivers/media/platform/exynos-gsc/gsc-core.h:297: warning: Function parameter or member 'pix_align' not described in 'gsc_variant'
drivers/media/platform/exynos-gsc/gsc-core.h:297: warning: Function parameter or member 'in_buf_cnt' not described in 'gsc_variant'
drivers/media/platform/exynos-gsc/gsc-core.h:297: warning: Function parameter or member 'out_buf_cnt' not described in 'gsc_variant'
drivers/media/platform/exynos-gsc/gsc-core.h:297: warning: Function parameter or member 'sc_up_max' not described in 'gsc_variant'
drivers/media/platform/exynos-gsc/gsc-core.h:297: warning: Function parameter or member 'sc_down_max' not described in 'gsc_variant'
drivers/media/platform/exynos-gsc/gsc-core.h:297: warning: Function parameter or member 'poly_sc_down_max' not described in 'gsc_variant'
drivers/media/platform/exynos-gsc/gsc-core.h:297: warning: Function parameter or member 'pre_sc_down_max' not described in 'gsc_variant'
drivers/media/platform/exynos-gsc/gsc-core.h:297: warning: Function parameter or member 'local_sc_down' not described in 'gsc_variant'
drivers/media/platform/exynos-gsc/gsc-core.h:310: warning: Function parameter or member 'clk_names' not described in 'gsc_driverdata'
drivers/media/platform/exynos-gsc/gsc-core.h:310: warning: Function parameter or member 'num_clocks' not described in 'gsc_driverdata'
drivers/media/platform/exynos-gsc/gsc-core.h:340: warning: Function parameter or member 'num_clocks' not described in 'gsc_dev'
drivers/media/platform/exynos-gsc/gsc-core.h:340: warning: Function parameter or member 'v4l2_dev' not described in 'gsc_dev'
drivers/media/platform/exynos-gsc/gsc-core.h:376: warning: Function parameter or member 'rotation' not described in 'gsc_ctx'
drivers/media/platform/exynos-gsc/gsc-core.h:376: warning: Function parameter or member 'hflip' not described in 'gsc_ctx'
drivers/media/platform/exynos-gsc/gsc-core.h:376: warning: Function parameter or member 'vflip' not described in 'gsc_ctx'
drivers/media/platform/exynos-gsc/gsc-core.h:376: warning: Function parameter or member 'gsc_ctrls' not described in 'gsc_ctx'
drivers/media/platform/exynos-gsc/gsc-core.h:376: warning: Function parameter or member 'out_colorspace' not described in 'gsc_ctx'
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Fixes these warnings:
drivers/media/platform/s5p-jpeg/jpeg-core.h:136: warning: Function parameter or member 'irq_ret' not described in 's5p_jpeg'
drivers/media/platform/s5p-jpeg/jpeg-core.h:136: warning: Function parameter or member 'irq_status' not described in 's5p_jpeg'
drivers/media/platform/s5p-jpeg/jpeg-core.h:168: warning: Function parameter or member 'memplanes' not described in 's5p_jpeg_fmt'
drivers/media/platform/s5p-jpeg/jpeg-core.h:168: warning: Function parameter or member 'subsampling' not described in 's5p_jpeg_fmt'
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Fixes these warnings:
drivers/media/platform/s3c-camif/camif-core.h:156: warning: Function parameter or member 'pix_limits' not described in 's3c_camif_variant'
drivers/media/platform/s3c-camif/camif-core.h:156: warning: Function parameter or member 'has_img_effect' not described in 's3c_camif_variant'
drivers/media/platform/s3c-camif/camif-core.h:156: warning: Function parameter or member 'vp_offset' not described in 's3c_camif_variant'
drivers/media/platform/s3c-camif/camif-core.h:232: warning: Function parameter or member 'vdev' not described in 'camif_vp'
drivers/media/platform/s3c-camif/camif-core.h:232: warning: Function parameter or member 'vb_queue' not described in 'camif_vp'
drivers/media/platform/s3c-camif/camif-core.h:232: warning: Function parameter or member 'offset' not described in 'camif_vp'
drivers/media/platform/s3c-camif/camif-core.h:297: warning: Function parameter or member 'ctrl_test_pattern' not described in 'camif_dev'
drivers/media/platform/s3c-camif/camif-core.h:297: warning: Function parameter or member 'ctrl_colorfx' not described in 'camif_dev'
drivers/media/platform/s3c-camif/camif-core.h:297: warning: Function parameter or member 'ctrl_colorfx_cbcr' not described in 'camif_dev'
drivers/media/platform/s3c-camif/camif-core.h:297: warning: Function parameter or member 'colorfx' not described in 'camif_dev'
drivers/media/platform/s3c-camif/camif-core.h:297: warning: Function parameter or member 'colorfx_cb' not described in 'camif_dev'
drivers/media/platform/s3c-camif/camif-core.h:297: warning: Function parameter or member 'colorfx_cr' not described in 'camif_dev'
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Give typo in kernel-doc documentation: hdr -> hrd
Fixes this warning:
drivers/media/platform/allegro-dvt/nal-h264.h:33: warning: expecting prototype for struct nal_h264_hdr_parameters. Prototype was for struct
nal_h264_hrd_parameters instead
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Reviewed-by: Michael Tretter <m.tretter@pengutronix.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The coda driver only runs on i.MX, which is a DT-only platform, so
remove the unneeded of_match_ptr().
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
A top-level documentation block was missing 'DOC:'.
Fix typos in vpu_wdt_reg_handler() and vpu_mapping_dm_addr().
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Cc: Irui Wang <irui.wang@mediatek.com>
Cc: Andrew-CT Chen <andrew-ct.chen@mediatek.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
mtk_vcodec_drv.h:
It's '@var:', not '@var - '.
In two places 'struct' was used instead of 'enum'.
vdec_drv_if.h:
It's '@var:', not '@var :'.
In one place 'struct' was used instead of 'enum'.
venc_ipi_msg.h:
It's '@data:', not '@data[8]:', i.e. arrays do not include the
size in kernel-doc.
It's '@var:', not 'var:'.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Cc: Alexandre Courbot <acourbot@chromium.org>
Cc: Tiffany Lin <tiffany.lin@mediatek.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
mtk_mdp_comp.h: MTK_MDP_COMP_TYPE_MAX was undocumented, but it
is also unused, so just remove it.
mtk_mdp_core.h: add missing '*' inside comment blocks, add a
missing : after '@ctrls' and add a missing struct keyword.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Cc: Eizan Miyamoto <eizan@chromium.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Add missing 'struct' keywords and fix typos in two struct member
names.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Cc: Xia Jiang <xia.jiang@mediatek.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The kernel-doc documentation for two structs was missing the
'struct' keyword.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Fix formatting of two enums and one struct.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Fix inline struct member documentation, was missing the
'@memb:' prefix.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Reviewed-by: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Enable support for SDM845 based Titan 170 ISPs.
Signed-off-by: Robert Foss <robert.foss@linaro.org>
Reviewed-by: Andrey Konovalov <andrey.konovalov@linaro.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
For Titan ISPs clocks fail to re-enable during vfe_get()
after any vfe has been halted and its corresponding power
domain power has been detached.
Since all of the clocks depend on all of the PDs, per
VFE PD detaching is no option for Gen2 HW.
In order to not have regressions on for Gen1 HW, refactor
the power domain management into hardware version specific
code paths.
Signed-off-by: Robert Foss <robert.foss@linaro.org>
Reviewed-by: Andrey Konovalov <andrey.konovalov@linaro.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Add register definitions for version 170 of the Titan architecture
and implement support for the CSIPHY subdevice.
Signed-off-by: Robert Foss <robert.foss@linaro.org>
Reviewed-by: Andrey Konovalov <andrey.konovalov@linaro.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Add register definitions for version 170 of the Titan architecture
and implement support for the CSID subdevice.
Signed-off-by: Robert Foss <robert.foss@linaro.org>
Reviewed-by: Andrey Konovalov <andrey.konovalov@linaro.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
In order to support Qualcomm ISP hardware architectures that diverge
from older architectures, the CSID subdevice drivers needs to be refactored
to better abstract the different ISP hardware architectures.
Signed-off-by: Robert Foss <robert.foss@linaro.org>
Reviewed-by: Andrey Konovalov <andrey.konovalov@linaro.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The CSI-2 spec defines format identifier for Data Type (DT),
and how the Decode Format (DF) & Encode Format (EF) are implemented.
The spec does however not define the DF, EF or Plain Format (PF)
identifiers, as those are vendor specific.
Plain formats describe the size of the pixels written by the RDI
units to memory. PLAIN8 for example has the size 8 bits, and
PLAIN32 32 bits. The appropriate Plain Format is determined by
the Decode Format used. The smallest Plain Format that is able
to contain a pixel of the used Decode Format is the appropriate
one to use.
As the vendor specific identifiers differ between hardware
generations, split them out into separate headers.
Signed-off-by: Robert Foss <robert.foss@linaro.org>
Reviewed-by: Andrey Konovalov <andrey.konovalov@linaro.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Add register definitions for version 170 of the Titan architecture
and implement support for the RDI output mode.
The RDI mode as opposed to the PIX output mode for the VFE unit does
not support any ISP functionality. This means essentially only
supporting dumping the output of the whatever the CSI decoder receives
from the sensor.
For example will a sensor outputting YUV pixel format frames, only
allow the VFE to dump those frames as they are received by the ISP
to memory through the RDI interface.
Signed-off-by: Robert Foss <robert.foss@linaro.org>
Reviewed-by: Andrey Konovalov <andrey.konovalov@linaro.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
In order to support Qualcomm ISP hardware architectures that diverge
from older architectures, the VFE subdevice driver needs to be refactored
to better abstract the different ISP architectures.
Gen1 represents the CAMSS ISP architecture. The ISP architecture developed
after CAMSS, Titan, will be referred to as Gen2.
Signed-off-by: Robert Foss <robert.foss@linaro.org>
Reviewed-by: Andrey Konovalov <andrey.konovalov@linaro.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
This driver supports multiple architecture versions of the Qualcomm ISP.
The CAMSS architecure which this driver is name after, and with the
introduction of this series, the Titan architecture.
The ISPIF is an IP-block that is only present in the CAMSS generation of
the architecture. In order to support the Titan generation, make the
ISPIF an optional subdevice.
Signed-off-by: Robert Foss <robert.foss@linaro.org>
Reviewed-by: Andrey Konovalov <andrey.konovalov@linaro.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Add enum representing the SDM845 SOC, which incorporates version
170 of the Titan architecture ISP.
Signed-off-by: Robert Foss <robert.foss@linaro.org>
Reviewed-by: Andrey Konovalov <andrey.konovalov@linaro.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
trace_printk() should not be used in production code,
since extra memory is used for special buffers whenever
trace_puts() is used.
Replace it with dev_dbg() which provides all of the desired
debugging functionality.
Signed-off-by: Robert Foss <robert.foss@linaro.org>
Suggested-by: Nicolas Boichat <drinkcat@chromium.org>
Reviewed-by: Nicolas Boichat <drinkcat@chromium.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Comment refers to ISPIF, but this is incorrect. Only
the VFE interrupts are handled by this function.
Signed-off-by: Robert Foss <robert.foss@linaro.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Function name in comment is wrong, and was changed to be
the same as the actual function name.
The comment was changed to kerneldoc format.
Signed-off-by: Robert Foss <robert.foss@linaro.org>
Reviewed-by: Andrey Konovalov <andrey.konovalov@linaro.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
In Kconfig it should be 'to'
In c8sectpfe-core.c it should be 'do'
Signed-off-by: Xiaofeng Cao <cxfcosmos@gmail.com>
Acked-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
V4L2 driver for the JPEG encoder/decoder from i.MX8QXP/i.MX8QM application
processors.
The multi-planar buffers API is used.
Baseline and extended sequential jpeg decoding is supported.
Progressive jpeg decoding is not supported by the IP.
Supports encode and decode of various formats:
YUV444, YUV422, YUV420, RGB, ARGB, Gray
YUV420 is the only multi-planar format supported.
Minimum resolution is 64 x 64, maximum 8192 x 8192.
The alignment requirements for the resolution depend on the format,
multiple of 16 resolutions should work for all formats.
v4l2-compliance tests are passing, including the
streaming tests, "v4l2-compliance -s"
[hverkuil: fix kernel-doc typos]
Signed-off-by: Mirela Rabulea <mirela.rabulea@nxp.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
When sun6i_video_remote_subdev() returns NULL to subdev, no error return
code of sun6i_video_start_streaming() is assigned.
To fix this bug, ret is assigned with -EINVAL in this case.
Reported-by: TOTE Robot <oslab@tsinghua.edu.cn>
Signed-off-by: Jia-Ju Bai <baijiaju1990@gmail.com>
Fixes: 5cc7522d89 ("media: sun6i: Add support for Allwinner CSI V3s")
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
When the list of xdev->notifier.asd_list is empty, no error return code
of xvip_graph_init() is assigned.
To fix this bug, ret is assigned with -ENOENT as error return code.
Reported-by: TOTE Robot <oslab@tsinghua.edu.cn>
Signed-off-by: Jia-Ju Bai <baijiaju1990@gmail.com>
Reviewed-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The CAL driver is video node centric, it controls the whole device
through the video device nodes. This limits the possible use cases as it
can't support sources that are more complex than a single subdev. To
support more complex hardware pipelines, implement support for the media
controller centric API. The exposed API can be selected through a module
parameter.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The cal_ctx_v4l2_init_formats() function does not handle error values
correctly when calling enum_mbus_code in subdevs, causing an infinite
loop if the subdev's enum_mbus_code returns some other error than EINVAL.
Fix the error handling.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
v4l2_fill_pix_format() already copies mbus_fmt.field, so no need to do
it again.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
In one of the error paths of the for_each_child_of_node() loop in
fimc_md_parse_one_endpoint, add missing call to of_node_put().
Fix the following coccicheck warning:
./drivers/media/platform/exynos4-is/media-dev.c:489:1-23: WARNING:
Function "for_each_child_of_node" should have of_node_put() before
return around line 492.
Reported-by: Abaci Robot <abaci@linux.alibaba.com>
Signed-off-by: Yang Li <yang.lee@linux.alibaba.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
On production devices the firmware could be located on different
places, this path could be provided by special firmware-name DT
property.
Here we check for existence of such DT property and if it exist
take the firmware path from there. Otherwise, if the property
is missing we fallback to the predefined path from driver resource
structure.
Signed-off-by: Stanimir Varbanov <stanimir.varbanov@linaro.org>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@somainline.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
This file uses memremap() now, so we should include io.h instead of
relying on any sort of implicit include elsewhere.
Cc: Dikshita Agarwal <dikshita@codeaurora.org>
Fixes: 0ca0ca9805 ("media: venus: core: add support to dump FW region")
Signed-off-by: Stephen Boyd <swboyd@chromium.org>
Reviewed-by: Fritz Koenig <frkoenig@chromium.org>
Signed-off-by: Stanimir Varbanov <stanimir.varbanov@linaro.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
If an error occurs after a successful 'of_icc_get()' call, it must be
undone.
Use 'devm_of_icc_get()' instead of 'of_icc_get()' to avoid the leak.
Update the remove function accordingly and axe the now unneeded
'icc_put()' calls.
Fixes: 32f0a6ddc8 ("media: venus: Use on-chip interconnect API")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: Stanimir Varbanov <stanimir.varbanov@linaro.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Add support for Access Unit Delimiter control into encoder.
Signed-off-by: Stanimir Varbanov <stanimir.varbanov@linaro.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Use the standard display_delay and display_delay_enable controls,
the legacy private MFC controls are kept for backward compatibility.
Acked-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Stanimir Varbanov <stanimir.varbanov@linaro.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Add support for display delay and display delay enable std controls.
With this we implement decoder decode output order (decode vs display).
Once firmware implement few new features the controls will be used
for other use-cases.
Signed-off-by: Stanimir Varbanov <stanimir.varbanov@linaro.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
MODULE_SUPPORTED_DEVICE was added in pre-git era and never was
implemented. We can safely remove it, because the kernel has grown
to have many more reliable mechanisms to determine if device is
supported or not.
Signed-off-by: Leon Romanovsky <leonro@nvidia.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Video engine uses eclk and vclk for its clock sources and its reset
control is coupled with eclk so the current clock enabling sequence works
like below.
Enable eclk
De-assert Video Engine reset
10ms delay
Enable vclk
It introduces improper reset on the Video Engine hardware and eventually
the hardware generates unexpected DMA memory transfers that can corrupt
memory region in random and sporadic patterns. This issue is observed
very rarely on some specific AST2500 SoCs but it causes a critical
kernel panic with making a various shape of signature so it's extremely
hard to debug. Moreover, the issue is observed even when the video
engine is not actively used because udevd turns on the video engine
hardware for a short time to make a query in every boot.
To fix this issue, this commit changes the clock handling logic to make
the reset de-assertion triggered after enabling both eclk and vclk. Also,
it adds clk_unprepare call for a case when probe fails.
clk: ast2600: fix reset settings for eclk and vclk
Video engine reset setting should be coupled with eclk to match it
with the setting for previous Aspeed SoCs which is defined in
clk-aspeed.c since all Aspeed SoCs are sharing a single video engine
driver. Also, reset bit 6 is defined as 'Video Engine' reset in
datasheet so it should be de-asserted when eclk is enabled. This
commit fixes the setting.
Fixes: d2b4387f3b ("media: platform: Add Aspeed Video Engine driver")
Signed-off-by: Jae Hyun Yoo <jae.hyun.yoo@linux.intel.com>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Reviewed-by: Eddie James <eajames@linux.ibm.com>
Fixes: d3d04f6c33 ("clk: Add support for AST2600 SoC")
Reviewed-by: Joel Stanley <joel@jms.id.au>
Acked-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
When setting the source media bus code in the resizer,
we first check that the current media bus code in the
source is yuv encoded format. This is done by
retrieving the data from the formats list of the isp
entity. This cause a crash when the media bus code on the
source is YUYV8_1_5X8 which is not supported by the isp
entity. Instead we should test the sink format of the resizer
which is guaranteed to be supported by the isp entity.
Fixes: 251b6eebb6 ("media: staging: rkisp1: rsz: Add support to more YUV encoded mbus codes on src pad")
Signed-off-by: Dafna Hirschfeld <dafna.hirschfeld@collabora.com>
Acked-by: Helen Koike <helen.koike@collabora.com>
Tested-by: Sebastian Fricke <sebastian.fricke.linux@gmail.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
This patch fixes the following trivial warnings w.r.t. kernel-doc usage:
drivers/media/common/videobuf2/frame_vector.c:38: warning: Excess function parameter 'gup_flags' description in 'get_vaddr_frames'
drivers/media/dvb-core/dvb_ca_en50221.c:193: warning: wrong kernel-doc identifier on line:
drivers/media/dvb-core/dvb_ca_en50221.c:1014: warning: expecting prototype for Wake up the DVB CA thread(). Prototype was for
dvb_ca_en50221_thread_wakeup() instead
drivers/media/dvb-core/dvb_ca_en50221.c:1023: warning: wrong kernel-doc identifier on line:
drivers/media/dvb-core/dvb_ca_en50221.c:1081: warning: wrong kernel-doc identifier on line:
drivers/media/dvb-core/dvb_ca_en50221.c:1112: warning: wrong kernel-doc identifier on line:
drivers/media/dvb-core/dvb_ca_en50221.c:1327: warning: wrong kernel-doc identifier on line:
drivers/media/dvb-core/dvb_ca_en50221.c:1411: warning: wrong kernel-doc identifier on line:
drivers/media/dvb-core/dvb_ca_en50221.c:1426: warning: wrong kernel-doc identifier on line:
drivers/media/dvb-core/dvb_ca_en50221.c:1582: warning: wrong kernel-doc identifier on line:
drivers/media/dvb-core/dvb_ca_en50221.c:1693: warning: wrong kernel-doc identifier on line:
drivers/media/dvb-core/dvb_ca_en50221.c:1743: warning: wrong kernel-doc identifier on line:
drivers/media/dvb-core/dvb_ca_en50221.c:1772: warning: wrong kernel-doc identifier on line:
drivers/media/dvb-core/dvb_ca_en50221.c:1830: warning: wrong kernel-doc identifier on line:
drivers/media/dvb-core/dvb_ca_en50221.c:1922: warning: wrong kernel-doc identifier on line:
drivers/media/rc/img-ir/img-ir-hw.c:628: warning: expecting prototype for img_ir_decoder_compatable(). Prototype was for
img_ir_decoder_compatible() instead
drivers/media/v4l2-core/v4l2-jpeg.c:461: warning: expecting prototype for jpeg_parse_header(). Prototype was for v4l2_jpeg_parse_header()
instead
drivers/media/platform/vsp1/vsp1_dl.c:166: warning: expecting prototype for struct vsp1_cmd_pool. Prototype was for struct vsp1_dl_cmd_pool
instead
drivers/media/platform/mtk-vpu/mtk_vpu.c:28: warning: expecting prototype for is a tiny processor controlling video hardware(). Prototype
was for INIT_TIMEOUT_MS() instead
drivers/media/platform/mtk-vcodec/vdec/vdec_vp9_if.c:73: warning: expecting prototype for struct vp9_fb_info. Prototype was for struct
vp9_ref_buf instead
drivers/media/platform/mtk-vcodec/vdec/vdec_vp9_if.c:85: warning: expecting prototype for struct vp9_fb_info. Prototype was for struct
vp9_sf_ref_fb instead
drivers/media/tuners/mt2063.c:1404: warning: expecting prototype for fLO_FractionalTerm(). Prototype was for MT2063_fLO_FractionalTerm() instead
drivers/media/tuners/mt2063.c:1465: warning: expecting prototype for CalcLO2Mult(). Prototype was for MT2063_CalcLO2Mult() instead
drivers/media/usb/pwc/pwc-dec23.c:640: warning: wrong kernel-doc identifier on line:
drivers/media/platform/exynos4-is/media-dev.c:820: warning: expecting prototype for __fimc_md_create_fimc_links(). Prototype was for
__fimc_md_create_fimc_sink_links() instead
drivers/media/i2c/s5k6aa.c:426: warning: expecting prototype for s5k6aa_configure_pixel_clock(). Prototype was for
s5k6aa_configure_pixel_clocks() instead
drivers/media/i2c/imx274.c:700: warning: wrong kernel-doc identifier on line:
drivers/media/i2c/imx274.c:735: warning: wrong kernel-doc identifier on line:
drivers/media/i2c/imx274.c:983: warning: wrong kernel-doc identifier on line:
Most are missing or mistyped function names.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
There is a repeating code pattern:
if (a || b) {
if (a)
...
if (b)
...
}
In this pattern, the first 'if' is redundant.
The code can be replaced with:
if (a)
...
if (b)
...
Signed-off-by: Dafna Hirschfeld <dafna.hirschfeld@collabora.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The mtk-smi driver can now be built as a loadable module, but
this leads to a build time regression when the drivers that
depend on it are built-in:
aarch64-linux-ld: drivers/media/platform/mtk-mdp/mtk_mdp_comp.o: in function `mtk_mdp_comp_clock_on':
mtk_mdp_comp.c:(.text.mtk_mdp_comp_clock_on+0x54): undefined reference to `mtk_smi_larb_get'
aarch64-linux-ld: drivers/media/platform/mtk-mdp/mtk_mdp_comp.o: in function `mtk_mdp_comp_clock_off':
mtk_mdp_comp.c:(.text.mtk_mdp_comp_clock_off+0x12c): undefined reference to `mtk_smi_larb_put'
Add a dependency on the interface, but keep allowing
compile-testing without that driver, as it was originally
intended.
Fixes: 50fc8d9232 ("memory: mtk-smi: Allow building as module")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Because of u32 type being used to store pixel clock rate, expression used
to calculate pipeline clocks (pixel_clock * bpp) produces wrong value due
to integer overflow. This patch changes data type used to store, pass and
retrieve pixel_clock from u32 to u64 to make this mistake less likely to
be repeated in the future.
Signed-off-by: Vladimir Lypak <junak.pub@gmail.com>
Acked-by: Robert Foss <robert.foss@linaro.org>
Signed-off-by: Andrey Konovalov <andrey.konovalov@linaro.org>
Reviewed-by: Jacopo Mondi <jacopo@jmondi.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
There are places in the camss driver where camss_get_pixel_clock() is
called to get the pixel rate (using V4L2_CID_PIXEL_RATE control) and to
calculate the link frequency from it. There is a case when this would
not work: when V4L2_CID_PIXEL_RATE gets the rate at which the pixels are
read (sampled) from the sensor's pixel array, and this rate is different
from the pixel transmission rate over the CSI link, the link frequency
value can't be calculated from the pixel rate. One needs to use
V4L2_CID_LINK_FREQ to get the link frequency in this case.
Replace such calls to camss_get_pixel_clock() with calls to a wrapper
around v4l2_get_link_freq(). v4l2_get_link_freq() tries V4L2_CID_LINK_FREQ
first, and if it is not implemented by the camera sensor driver, falls
back to V4L2_CID_PIXEL_RATE to calculate the link frequency value from.
Calls to camss_get_pixel_clock() from vfe_[check,set]_clock_rates()
are left intact as it looks like this VFE clock does depend on the
rate the pixel samples comes out of the camera sensor, not on the
frequency at which the link between the sensor and the CSI receiver
operates.
Signed-off-by: Andrey Konovalov <andrey.konovalov@linaro.org>
Acked-by: Robert Foss <robert.foss@linaro.org>
Reviewed-by: Jacopo Mondi <jacopo@jmondi.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Use getter and setter functions, for a variety of data types.
Signed-off-by: Julia Lawall <Julia.Lawall@inria.fr>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Don't populate the const arrays on the stack but instead it
static. Makes the object code smaller by 8 bytes:
Before:
text data bss dec hex filename
12504 4568 0 17072 42b0 media/platform/sti/hva/hva-h264.o
After:
text data bss dec hex filename
12272 4792 0 17064 42a8 media/platform/sti/hva/hva-h264.o
(gcc version 10.2.0)
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The histogram mode is set using 'rkisp1_params_set_bits'.
Only the bits of the mode should be the value argument for
that function. Otherwise bits outside the mode mask are
turned on which is not what was intended.
Fixes: bae1155cf5 ("media: staging: rkisp1: add output device for parameters")
Signed-off-by: Dafna Hirschfeld <dafna.hirschfeld@collabora.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
RZ/G2L SoC has no UIF. This patch fixes null pointer access, when UIF
module is not used.
Fixes: 5e824f989e6e8("media: v4l: vsp1: Integrate DISCOM in display pipeline")
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
RZ/G2L SoC has only BRS. This patch fixes null pointer access,when only
BRS is enabled.
Fixes: cbb7fa49c7466("media: v4l: vsp1: Rename BRU to BRx")
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
- replace mm/frame_vector.c by get_user_pages in misc/habana and
drm/exynos drivers, then move that into media as it's sole user
- close race in generic_access_phys
- s390 pci ioctl fix of this series landed in 5.11 already
- properly revoke iomem mappings (/dev/mem, pci files)
-----BEGIN PGP SIGNATURE-----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=lQoR
-----END PGP SIGNATURE-----
Merge tag 'topic/iomem-mmap-vs-gup-2021-02-22' of git://anongit.freedesktop.org/drm/drm
Pull follow_pfn() updates from Daniel Vetter:
"Fixes around VM_FPNMAP and follow_pfn:
- replace mm/frame_vector.c by get_user_pages in misc/habana and
drm/exynos drivers, then move that into media as it's sole user
- close race in generic_access_phys
- s390 pci ioctl fix of this series landed in 5.11 already
- properly revoke iomem mappings (/dev/mem, pci files)"
* tag 'topic/iomem-mmap-vs-gup-2021-02-22' of git://anongit.freedesktop.org/drm/drm:
PCI: Revoke mappings like devmem
PCI: Also set up legacy files only after sysfs init
sysfs: Support zapping of binary attr mmaps
resource: Move devmem revoke code to resource framework
/dev/mem: Only set filp->f_mapping
PCI: Obey iomem restrictions for procfs mmap
mm: Close race in generic_access_phys
media: videobuf2: Move frame_vector into media subsystem
mm/frame-vector: Use FOLL_LONGTERM
misc/habana: Use FOLL_LONGTERM for userptr
misc/habana: Stop using frame_vector helpers
drm/exynos: Use FOLL_LONGTERM for g2d cmdlists
drm/exynos: Stop using frame_vector helpers
- Sync dtc to upstream version v1.6.0-51-g183df9e9c2b9 and build
host fdtoverlay
- Add kbuild support to build DT overlays (%.dtbo)
- Drop NULLifying match table in of_match_device(). In preparation for
this, there are several driver cleanups to use
(of_)?device_get_match_data().
- Drop pointless wrappers from DT struct device API
- Convert USB binding schemas to use graph schema and remove old plain
text graph binding doc
- Convert spi-nor and v3d GPU bindings to DT schema
- Tree wide schema fixes for if/then schemas, array size constraints,
and undocumented compatible strings in examples
- Handle 'no-map' correctly for already reserved memblock regions
-----BEGIN PGP SIGNATURE-----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=9V4A
-----END PGP SIGNATURE-----
Merge tag 'devicetree-for-5.12' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux
Pull devicetree updates from Rob Herring:
- Sync dtc to upstream version v1.6.0-51-g183df9e9c2b9 and build host
fdtoverlay
- Add kbuild support to build DT overlays (%.dtbo)
- Drop NULLifying match table in of_match_device().
In preparation for this, there are several driver cleanups to use
(of_)?device_get_match_data().
- Drop pointless wrappers from DT struct device API
- Convert USB binding schemas to use graph schema and remove old plain
text graph binding doc
- Convert spi-nor and v3d GPU bindings to DT schema
- Tree wide schema fixes for if/then schemas, array size constraints,
and undocumented compatible strings in examples
- Handle 'no-map' correctly for already reserved memblock regions
* tag 'devicetree-for-5.12' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux: (35 commits)
driver core: platform: Drop of_device_node_put() wrapper
of: Remove of_dev_{get,put}()
dt-bindings: usb: Change descibe to describe in usbmisc-imx.txt
dt-bindings: can: rcar_canfd: Group tuples in pin control properties
dt-bindings: power: renesas,apmu: Group tuples in cpus properties
dt-bindings: mtd: spi-nor: Convert to DT schema format
dt-bindings: Use portable sort for version cmp
dt-bindings: ethernet-controller: fix fixed-link specification
dt-bindings: irqchip: Add node name to PRUSS INTC
dt-bindings: interconnect: Fix the expected number of cells
dt-bindings: Fix errors in 'if' schemas
dt-bindings: iommu: renesas,ipmmu-vmsa: Make 'power-domains' conditionally required
dt-bindings: Fix undocumented compatible strings in examples
kbuild: Add support to build overlays (%.dtbo)
scripts: dtc: Remove the unused fdtdump.c file
scripts: dtc: Build fdtoverlay tool
scripts/dtc: Update to upstream version v1.6.0-51-g183df9e9c2b9
scripts: dtc: Fetch fdtoverlay.c from external DTC project
dt-bindings: thermal: sun8i: Fix misplaced schema keyword in compatible strings
dt-bindings: iio: dac: Fix AD5686 references
...
-----BEGIN PGP SIGNATURE-----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=/wKL
-----END PGP SIGNATURE-----
Merge tag 'media/v5.12-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media
Pull media updates from Mauro Carvalho Chehab:
- some core fixes in VB2 mem2mem support
- some improvements and cleanups in V4L2 async kAPI
- newer controls in V4L2 API for H-264 and HEVC codecs
- allegro-dvt driver was promoted from staging
- new i2c sendor drivers: imx334, ov5648, ov8865
- new automobile camera module: rdacm21
- ipu3 cio2 driver started gained support for some ACPI BIOSes
- new ATSC frontend: MaxLinear mxl692 VSB tuner/demod
- the SMIA/CCS driver gained more support for CSS standard
- several driver fixes, updates and improvements
* tag 'media/v5.12-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media: (362 commits)
media: v4l: async: Fix kerneldoc documentation for async functions
media: i2c: max9271: Add MODULE_* macros
media: i2c: Kconfig: Make MAX9271 a module
media: imx334: 'ret' is uninitialized, should have been PTR_ERR()
media: i2c: Add imx334 camera sensor driver
media: dt-bindings: media: Add bindings for imx334
media: ov8856: Configure sensor for GRBG Bayer for all modes
media: i2c: imx219: Implement V4L2_CID_LINK_FREQ control
media: ov5675: fix vflip/hflip control
media: ipu3-cio2: Build bridge only if ACPI is enabled
media: Remove the legacy v4l2-clk API
media: ov6650: Use the generic clock framework
media: mt9m111: Use the generic clock framework
media: ov9640: Use the generic clock framework
media: pxa_camera: Drop the v4l2-clk clock register
media: mach-pxa: Register the camera sensor fixed-rate clock
media: i2c: imx258: get clock from device properties and enable it via runtime PM
media: i2c: imx258: simplify getting state container
media: i2c: imx258: add support for binding via device tree
media: dt-bindings: media: imx258: add bindings for IMX258 sensor
...
Now that mach-based PXA platforms are registering proper
fixed-rate clocks through the CCF, the v4l2-clk clock
is no longer required.
Drop this clock, so the driver no longer depends on the
legacy v4l2-clk API.
Signed-off-by: Ezequiel Garcia <ezequiel@collabora.com>
Acked-by: Petr Cvek <petrcvekcz@gmail.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Writing to REG_CLKCTRL with the power off causes a hang. Enable the
device first.
Cc: stable@vger.kernel.org # 5.10+
Signed-off-by: Lubomir Rintel <lkundrak@v3.sk>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The functions that add an async subdev to an async subdev notifier take
as an argument the size of the container structure they need to
allocate. This is error prone, as passing an invalid size will not be
caught by the compiler. Wrap those functions in macros that take a
container type instead of a size, and cast the returned pointer to the
desired type. The compiler will catch mistakes if the incorrect type is
passed to the macro, as the assignment types won't match.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Signed-off-by: Ezequiel Garcia <ezequiel@collabora.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Reviewed-by: Helen Koike <helen.koike@collabora.com>
Reviewed-by: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com> (core+ti-cal)
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
There are no users for vpif_display_config.asd_sizes
and vpif_display_config.asd members, which means the v4l2-async
subdevices aren't being defined anywhere.
Remove the v4l2-async, leaving only the synchronous setup.
Signed-off-by: Ezequiel Garcia <ezequiel@collabora.com>
Reviewed-by: Helen Koike <helen.koike@collabora.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The use of v4l2_async_notifier_add_subdev will be discouraged.
Drivers are instead encouraged to use a helper such as
v4l2_async_notifier_add_fwnode_remote_subdev.
This fixes a misuse of the API, as v4l2_async_notifier_add_subdev
should get a kmalloc'ed struct v4l2_async_subdev.
Use the appropriate helper: v4l2_async_notifier_add_i2c_subdev
or v4l2_async_notifier_add_fwnode_remote_subdev, which handles
the needed setup, instead of open-coding it.
Signed-off-by: Ezequiel Garcia <ezequiel@collabora.com>
Reviewed-by: Helen Koike <helen.koike@collabora.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The use of v4l2_async_notifier_add_subdev will be discouraged.
Drivers are instead encouraged to use a helper such as
v4l2_async_notifier_add_i2c_subdev.
This fixes a misuse of the API, as v4l2_async_notifier_add_subdev
should get a kmalloc'ed struct v4l2_async_subdev,
removing some boilerplate code while at it.
Use the appropriate helper: v4l2_async_notifier_add_i2c_subdev
or v4l2_async_notifier_add_fwnode_remote_subdev, which handles
the needed setup, instead of open-coding it.
Using v4l2-async to allocate the driver-specific structs,
requires to change struct ceu_subdev so the embedded
struct v4l2_async_subdev is now the first element.
Signed-off-by: Ezequiel Garcia <ezequiel@collabora.com>
Reviewed-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Reviewed-by: Helen Koike <helen.koike@collabora.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The use of v4l2_async_notifier_add_subdev will be discouraged.
Drivers are instead encouraged to use a helper such as
v4l2_async_notifier_add_fwnode_remote_subdev.
This fixes a misuse of the API, as v4l2_async_notifier_add_subdev
should get a kmalloc'ed struct v4l2_async_subdev,
removing some boilerplate code while at it.
Use the appropriate helper: v4l2_async_notifier_add_i2c_subdev
or v4l2_async_notifier_add_fwnode_remote_subdev, which handles
the needed setup, instead of open-coding it.
Signed-off-by: Ezequiel Garcia <ezequiel@collabora.com>
Reviewed-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Reviewed-by: Helen Koike <helen.koike@collabora.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The use of v4l2_async_notifier_add_subdev will be discouraged.
Drivers are instead encouraged to use a helper such as
v4l2_async_notifier_add_fwnode_remote_subdev.
This fixes a misuse of the API, as v4l2_async_notifier_add_subdev
should get a kmalloc'ed struct v4l2_async_subdev,
removing some boilerplate code while at it.
Use the appropriate helper v4l2_async_notifier_add_fwnode_remote_subdev,
which handles the needed setup, instead of open-coding it.
Signed-off-by: Ezequiel Garcia <ezequiel@collabora.com>
Reviewed-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Reviewed-by: Helen Koike <helen.koike@collabora.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The use of v4l2_async_notifier_add_subdev will be discouraged.
Drivers are instead encouraged to use a helper such as
v4l2_async_notifier_add_fwnode_remote_subdev.
This fixes a misuse of the API, as v4l2_async_notifier_add_subdev
should get a kmalloc'ed struct v4l2_async_subdev,
removing some boilerplate code while at it.
Use the appropriate helper v4l2_async_notifier_add_fwnode_remote_subdev,
which handles the needed setup, instead of open-coding it.
Signed-off-by: Ezequiel Garcia <ezequiel@collabora.com>
Reviewed-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Reviewed-by: Helen Koike <helen.koike@collabora.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The use of v4l2_async_notifier_add_subdev will be discouraged.
Drivers are instead encouraged to use a helper such as
v4l2_async_notifier_add_fwnode_remote_subdev.
This fixes a misuse of the API, as v4l2_async_notifier_add_subdev
should get a kmalloc'ed struct v4l2_async_subdev,
removing some boilerplate code while at it.
Use the appropriate helper v4l2_async_notifier_add_fwnode_remote_subdev,
which handles the needed setup, instead of open-coding it.
This results in removal of the now unneeded driver-specific state
struct dcmi_graph_entity, keeping track of just the source
subdevice.
Signed-off-by: Ezequiel Garcia <ezequiel@collabora.com>
Reviewed-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Reviewed-by: Helen Koike <helen.koike@collabora.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The use of v4l2_async_notifier_add_subdev will be discouraged.
Drivers are instead encouraged to use a helper such as
v4l2_async_notifier_add_fwnode_remote_subdev.
This fixes a misuse of the API, as v4l2_async_notifier_add_subdev
should get a kmalloc'ed struct v4l2_async_subdev,
removing some boilerplate code while at it.
Signed-off-by: Ezequiel Garcia <ezequiel@collabora.com>
Reviewed-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Reviewed-by: Helen Koike <helen.koike@collabora.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Change v4l2_async_notifier_add_fwnode_remote_subdev semantics
so it allocates the struct v4l2_async_subdev pointer.
This makes the API consistent: the v4l2-async subdevice addition
functions have now a unified usage model. This model is simpler,
as it makes v4l2-async responsible for the allocation and release
of the subdevice descriptor, and no longer something the driver
has to worry about.
On the user side, the change makes the API simpler for the drivers
to use and less error-prone.
Signed-off-by: Ezequiel Garcia <ezequiel@collabora.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Reviewed-by: Helen Koike <helen.koike@collabora.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Later variants of the rkisp1 block use more entries in some arrays:
RKISP1_CIF_ISP_AE_MEAN_MAX 25 -> 81
RKISP1_CIF_ISP_HIST_BIN_N_MAX 16 -> 32
RKISP1_CIF_ISP_GAMMA_OUT_MAX_SAMPLES 17 -> 34
RKISP1_CIF_ISP_HISTOGRAM_WEIGHT_GRIDS_SIZE 25 -> 81
and we can still extend the uapi during the 5.11-rc cycle, so do that
now to be on the safe side.
V10 and V11 only need the smaller sizes, while V12 and V13 needed
the larger sizes.
When adding the bigger sizes make sure, values filled from hardware
values and transmitted to userspace don't leak kernel data by zeroing
them beforehand.
Signed-off-by: Heiko Stuebner <heiko.stuebner@theobroma-systems.com>
Signed-off-by: Dafna Hirschfeld <dafna.hirschfeld@collabora.com>
Reviewed-by: Ezequiel Garcia <ezequiel@collabora.com>
Acked-by: Helen Koike <helen.koike@collabora.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The IP block evolved from its rk3288/rk3399 base and the vendor
designates them with a numerical version. rk3399 for example
is designated V10 probably meaning V1.0.
There doesn't seem to be an actual version register we could read that
information from, so allow the match_data to carry that information
for future differentiation.
Also carry that information in the hw_revision field of the media-
controller API, so that userspace also has access to that.
The added versions are:
- V10: at least rk3288 + rk3399
- V11: seemingly unused as of now, but probably appeared in some soc
- V12: at least rk3326 + px30
- V13: at least rk1808
[fix checkpatch warning don't use multiple blank lines]
Signed-off-by: Heiko Stuebner <heiko.stuebner@theobroma-systems.com>
Signed-off-by: Dafna Hirschfeld <dafna.hirschfeld@collabora.com>
Reviewed-by: Ezequiel Garcia <ezequiel@collabora.com>
Acked-by: Helen Koike <helen.koike@collabora.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The uapi right now specifies an array size of 28 but the actual number
of elements is only 25 with the last 3 being unused.
Reduce the array size to the correct number of elements and change
the params code to iterate the array 25 times.
Signed-off-by: Heiko Stuebner <heiko.stuebner@theobroma-systems.com>
Signed-off-by: Dafna Hirschfeld <dafna.hirschfeld@collabora.com>
Acked-by: Helen Koike <helen.koike@collabora.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
hist_bins is an array of type __u32. Each entry represents
a 20 bit value. So mask out the unused bits.
Signed-off-by: Dafna Hirschfeld <dafna.hirschfeld@collabora.com>
Acked-by: Helen Koike <helen.koike@collabora.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
hist_bins is an array of type __u32. Each entry represent
a 20 bit fixed point value as documented inline.
The cast to u8 when setting the values is wrong. Remove it.
Signed-off-by: Dafna Hirschfeld <dafna.hirschfeld@collabora.com>
Reviewed-by: Heiko Stuebner <heiko@sntech.de>
Acked-by: Helen Koike <helen.koike@collabora.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
HFI_PROPERTY_CONFIG_VENC_IDR_PERIOD is supported for only
H264 & HEVC codec. There is no need to set it for VP8 since
all key frames are treated as IDR frames for VP8.
Signed-off-by: Dikshita Agarwal <dikshita@codeaurora.org>
Signed-off-by: Stanimir Varbanov <stanimir.varbanov@linaro.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
- return correct width and height for G_SELECTION
- update capture port wxh with rectangle wxh.
- add support for HFI_PROPERTY_PARAM_UNCOMPRESSED_PLANE_ACTUAL_INFO
to set stride info and chroma offset to FW.
Signed-off-by: Dikshita Agarwal <dikshita@codeaurora.org>
Signed-off-by: Stanimir Varbanov <stanimir.varbanov@linaro.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Presently we use device_link to control core power domain. But this
leads to issues because the genpd doesn't guarantee synchronous on/off
for supplier devices. Switch to manually control by pmruntime calls.
Tested-by: Fritz Koenig <frkoenig@chromium.org>
Signed-off-by: Stanimir Varbanov <stanimir.varbanov@linaro.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The dependency on interconnect in the Kconfig was introduced to avoid
the case of interconnect=m and driver=y, but the interconnect framework
has been converted from tristate to bool now. Remove the dependency as
the framework can't be a module anymore.
Signed-off-by: Georgi Djakov <georgi.djakov@linaro.org>
Signed-off-by: Stanimir Varbanov <stanimir.varbanov@linaro.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Add support to dump video FW region during FW crash
using devcoredump helpers.
Signed-off-by: Dikshita Agarwal <dikshita@codeaurora.org>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Signed-off-by: Stanimir Varbanov <stanimir.varbanov@linaro.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Fix the following sparse warning:
hfi_plat_bufs_v6.c:1242:5: warning: symbol 'bufreq_enc' was not declared.
Should it be static?
Signed-off-by: Zou Wei <zou_wei@huawei.com>
Signed-off-by: Stanimir Varbanov <stanimir.varbanov@linaro.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
In the case where plat->codecs is NULL the variable count is uninitialized
but is being checked to see if it is 0. Fix this by initializing
count to 0.
Addresses-Coverity: ("Uninitialized scalar variable")
Fixes: e29929266b ("media: venus: Get codecs and capabilities from hfi platform")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Stanimir Varbanov <stanimir.varbanov@linaro.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The Allegro Codec supports HEVC encoding. The messages to the MCU are
the same for H.264 and HEVC, but some options have to be changed. These
are actually only a few options.
The driver, however, must add the HEVC VPS/SPS/PPS NAL Units to the
coded stream and must properly provide the HEVC format and controls to
user space.
[hverkuil: fix warning for wrong enum type (h264 instead of hevc)]
Signed-off-by: Michael Tretter <m.tretter@pengutronix.de>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
These controls are specific to H.264 and shall only be activated, if the
coded format is H.264.
Signed-off-by: Michael Tretter <m.tretter@pengutronix.de>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The HEVC Non-VCL NAL units require more space than the H.264 Non-VCL NAL
units. Therefore, the driver needs to reserve more space in front of the
actual coded data that is written by the hardware codec.
Increase the offset that shall be used by the hardware codec from 64
bytes to 128 bytes which is as arbitrary as before.
Signed-off-by: Michael Tretter <m.tretter@pengutronix.de>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The maximum bitrate and the size of the CPB are dependent on the level.
As the levels differ between the different codecs, the functions to get
the maximum bitrate and CPB must be codec specific, too.
Rename the functions to make it obvious that the function are only valid
for H.264.
Signed-off-by: Michael Tretter <m.tretter@pengutronix.de>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The driver only supports CAVLC for H.264, but HEVC only uses CABAC. As
the driver has to explicitly tell the MCU to use CABAC for HEVC, add a
helper function to get the entropy mode.
Signed-off-by: Michael Tretter <m.tretter@pengutronix.de>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
V4L2 specifies different controls for the QP values of different codecs.
Simplify users that just care for the QP values by providing accessor
function that return the correct control based on the currently set
codec.
Signed-off-by: Michael Tretter <m.tretter@pengutronix.de>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The profile and level are straight copies from the v4l2-ctrls. Avoid
duplication and directly read the value of the v4l2-ctrl.
Signed-off-by: Michael Tretter <m.tretter@pengutronix.de>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The cpb_size and the gop_size are straight copies of the values in the
v4l2-ctrls. To avoid this duplication, directly get the values from the
v4l2-ctrls and remove the copies.
Signed-off-by: Michael Tretter <m.tretter@pengutronix.de>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The cbp_size_value_minus1 in the SPS can scaled using cpb_size_scale to
reduce the number of bits necessary to encode the value. For simplicity,
the scaling was set to 1.
Restructure to the code to make it easier to drop the cbp_size from the
channel and as we are at it, also properly implement the scaling.
Signed-off-by: Michael Tretter <m.tretter@pengutronix.de>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
As the driver now uses the v4l2-ctrls to setup the channel, there is no
need to explicitly set the bitrate. The initial bitrate is now set via
the same path as if it is set from userspace using the v4l2-ctrl.
Signed-off-by: Michael Tretter <m.tretter@pengutronix.de>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
v4l2_ctrl_handler_setup() calls s_ctrl for all controls of the handler.
This ensures that the channel is initialized using the default values of
the v4l2-ctrls.
Signed-off-by: Michael Tretter <m.tretter@pengutronix.de>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The log2_max_poc field is used to set log2_max_pic_order_cnt_lsb_minus4
for the coded stream. It has an allowed range of 0 to 12.
param contains the value without the minus4, but since firmware
version 2019.1, the value has to be log2_max_pic_order_cnt_lsb - 1,
presumably to fit the maximum value of 16 into a 4 bit field.
The driver does not support firmware version 2019.1. Thus, change the
behaviour starting from firmware version 2019.2.
Signed-off-by: Michael Tretter <m.tretter@pengutronix.de>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
There are several encoding options that are hard coded in the parameter
that is used to configure the hardware codec. However, some of the
options must be written to the SPS/PPS by the driver. Furthermore, some
of the options depend on the codec that is used (i.e. H.264 or HEVC).
Therefore, move options that depend on the codec to the channel and add
constants for options that are independent of the codec but must be
written to the SPS/PPS.
Signed-off-by: Michael Tretter <m.tretter@pengutronix.de>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
A format change (i.e. the frame size or the codec) has multiple effects
on a channel:
- The available controls
- The limits of the available controls
- The default encoding options
To avoid scattering the changes all over the driver, add a new function
that goes over the channel and does all required adjustments.
Signed-off-by: Michael Tretter <m.tretter@pengutronix.de>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
In order to support different codecs, the driver must support changing
the format on CAPTURE. Therefore, the driver needs to handle S_FMT on
CAPTURE.
As the driver will have a different number of formats for OUTPUT and
CAPTURE, split the check for the format index in ENUM_FMT into CAPTURE
and OUTPUT.
Signed-off-by: Michael Tretter <m.tretter@pengutronix.de>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
When encoding a video as HEVC, the allegro driver needs to generate the
Non-VCL NAL units for HEVC. Do the same as for H.264 and add a module
that takes C structs for the VPS/SPS/PPS and encodes the fields as RBPS
as specified by "ITU-T Rec. H.265 (02/2018) high efficiency video
coding".
[hverkuil: add missing static for nal_hevc_write/read_start_code_prefix]
[hverkuil: fix typo: pps -> vps in nal_hevc_write_vps]
Signed-off-by: Michael Tretter <m.tretter@pengutronix.de>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Allow generators to explicitly signal an error if the C structs contain
unsupported or invalid fields.
Signed-off-by: Michael Tretter <m.tretter@pengutronix.de>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The RBSP structure is the same for HEVC and H.264. In order to be able
to reuse the RBSP handler for generating HEVC NAL units, extract the
functions from the H.264 generator.
Signed-off-by: Michael Tretter <m.tretter@pengutronix.de>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The event route for VIN running with a media controller (Gen3) is
incorrect as all events are only routed to the video device that are
used to register the async notifier.
Remedy this be examining which subdevice generated the event and route
it to all VIN(s) that are connected to that subdevice.
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Do not attempt to stop the streaming if the stream is not running.
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
When DEBUG is defined this error occurs
drivers/media/platform/pxa_camera.c:1410:7: error:
‘i’ undeclared (first use in this function)
for (i = 0; i < vb->num_planes; i++)
^
The variable 'i' is missing, so declare it.
Fixes: 6f28435d1c ("[media] media: platform: pxa_camera: trivial move of functions")
Signed-off-by: Tom Rix <trix@redhat.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
When DEBUG is defined this error occurs
drivers/media/platform/mtk-vcodec/mtk_vcodec_enc_drv.c:306:41:
error: ‘i’ undeclared (first use in this function)
mtk_v4l2_debug(2, "reg[%d] base=0x%p", i, dev->reg_base[VENC_SYS]);
Reviewing the old line
mtk_v4l2_debug(2, "reg[%d] base=0x%p", i, dev->reg_base[i]);
All the i's need to be changed to VENC_SYS.
Fix a similar error for VENC_LT_SYS.
Fixes: 0dc4b32861 ("media: mtk-vcodec: venc: support SCP firmware")
Signed-off-by: Tom Rix <trix@redhat.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
In preparation to enable -Wimplicit-fallthrough for Clang, fix a warning
by explicitly adding a break statement instead of letting the code fall
through to the next case.
Link: https://github.com/KSPP/linux/issues/115
Signed-off-by: Gustavo A. R. Silva <gustavoars@kernel.org>
Reviewed-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Fixes this smatch warning:
drivers/media/platform/sti/c8sectpfe/c8sectpfe-core.c:829 c8sectpfe_probe() warn: missing error code 'ret'
Set ret to -EINVAL if the reset gpio was not found.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Fixes this smatch warning:
drivers/media/platform/davinci/vpbe.c:632 vpbe_initialize() warn: missing error code 'ret'
The function returns 'ret', but instead 'err' was set to -ENOMEM.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Cc: "Lad, Prabhakar" <prabhakar.csengg@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
This driver can use the replacement API instead of calling
of_match_device() and then dereferencing the pointer that is returned.
This nicely avoids referencing the match table when it is undefined with
configurations where CONFIG_OF=n.
Signed-off-by: Stephen Boyd <swboyd@chromium.org>
Acked-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Acked-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Jacopo Mondi <jacopo@jmondi.org>
Cc: Mauro Carvalho Chehab <mchehab@kernel.org>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Frank Rowand <frowand.list@gmail.com>
Cc: <linux-media@vger.kernel.org>
Cc: <linux-renesas-soc@vger.kernel.org>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20210123034428.2841052-2-swboyd@chromium.org
The asd allocated with v4l2_async_notifier_add_fwnode_subdev() must be
of size cal_v4l2_async_subdev, otherwise access to
cal_v4l2_async_subdev->phy will go to unallocated memory.
Fixes: 8fcb7576ad ("media: ti-vpe: cal: Allow multiple contexts per subdev notifier")
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Fix the following sparse warning:
drivers/media/platform/ti-vpe/cal-camerarx.c:783:32: warning: symbol 'cal_camerarx_media_ops' was not declared. Should it be static?
Signed-off-by: Zou Wei <zou_wei@huawei.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Add support for base layer priority ID control in encoder.
This is a preparation patch to support v6.
[hverkuil: changed 54 to 51 in v4l2_ctrl_handler_init]
Signed-off-by: Dikshita Agarwal <dikshita@codeaurora.org>
Acked-by: Stanimir Varbanov <stanimir.varbanov@linaro.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Add support for frame type specific min and max qp controls
for encoder.
This is a preparation patch to support v6.
Signed-off-by: Dikshita Agarwal <dikshita@codeaurora.org>
Acked-by: Stanimir Varbanov <stanimir.varbanov@linaro.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Now when everything is in place wire up buffer requirements
from hfi platform buffers to the buffer requirements helper.
Signed-off-by: Stanimir Varbanov <stanimir.varbanov@linaro.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Handle progressive/interlaced bitstream event by similar way as
bit depth.
Signed-off-by: Stanimir Varbanov <stanimir.varbanov@linaro.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Wire up hfi platform codec and capabilities instead of
getting them from firmware.
Signed-off-by: Stanimir Varbanov <stanimir.varbanov@linaro.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Add a new file for hfi platform buffer size and count calculations
for v6.
Signed-off-by: Stanimir Varbanov <stanimir.varbanov@linaro.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
>From Venus v6 and beyond the buffer size and count have to be
calculated in the v4l2 driver instead of getting them from
firmware.
Signed-off-by: Stanimir Varbanov <stanimir.varbanov@linaro.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Starting from v6 we have one more hfi property which will be needed
to calculate buffer sizes/count for particular codec and session type.
Signed-off-by: Stanimir Varbanov <stanimir.varbanov@linaro.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Add ops to get the supported by the platform codecs and capabilities.
Signed-off-by: Stanimir Varbanov <stanimir.varbanov@linaro.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Now when we have hfi platform make venus capabilities an
hfi platform capabilities.
Signed-off-by: Stanimir Varbanov <stanimir.varbanov@linaro.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Introduce a new hfi platform to cover differences between hfi
versions. As a start move vpp/vsp freq data in that hfi
platform, more platform data will come later.
Signed-off-by: Stanimir Varbanov <stanimir.varbanov@linaro.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The core caps are filled but not used, delete them. In case we
need them we can re-introduce.
Signed-off-by: Stanimir Varbanov <stanimir.varbanov@linaro.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Skip calculating instance frequency if it is not in running state.
Signed-off-by: Stanimir Varbanov <stanimir.varbanov@linaro.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
For resolutions below 720p the size of the compressed buffer must
be bigger. Correct this by checking the resolution when calculating
buffer size and multiply by eight.
Signed-off-by: Stanimir Varbanov <stanimir.varbanov@linaro.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The hfi_session_init can be called many times and it returns
EINVAL when the session was already initialized. This error code
(EINVAL) is confusing for the callers. Change hfi_session_init to
return EALREADY error code when the session has been already
initialized.
Tested-by: Fritz Koenig <frkoenig@chromium.org>
Signed-off-by: Stanimir Varbanov <stanimir.varbanov@linaro.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
For synchronous commands, update the message queue variable.
This would inform video firmware to raise interrupt on host
CPU whenever there is a response for such commands.
Signed-off-by: Vikash Garodia <vgarodia@codeaurora.org>
Tested-by: Fritz Koenig <frkoenig@chromium.org>
Signed-off-by: Stanimir Varbanov <stanimir.varbanov@linaro.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Currently we rely on firmware to return error when we reach the maximum
supported number of sessions. But this errors are happened at reqbuf
time which is a bit later. The more reasonable way looks like is to
return the error on driver open.
To achieve that modify hfi_session_create to return error when we reach
maximum count of sessions and thus refuse open.
Tested-by: Fritz Koenig <frkoenig@chromium.org>
Signed-off-by: Stanimir Varbanov <stanimir.varbanov@linaro.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Init the hfi session only once in queue_setup and also cover that
with inst->lock.
Tested-by: Fritz Koenig <frkoenig@chromium.org>
Signed-off-by: Stanimir Varbanov <stanimir.varbanov@linaro.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
If the DRC is near the end of the stream the client
may send a V4L2_DEC_CMD_STOP before the DRC occurs.
V4L2_DEC_CMD_STOP puts the driver into the
VENUS_DEC_STATE_DRAIN state. DRC must be aware so
that after the DRC event the state can be restored
correctly.
Signed-off-by: Fritz Koenig <frkoenig@chromium.org>
Signed-off-by: Stanimir Varbanov <stanimir.varbanov@linaro.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
DRC events can happen virtually at anytime, including when we are
starting a seek. Should this happen, we must make sure to return to the
DRC state, otherwise the firmware will expect buffers of the new
resolution whereas userspace will still work with the old one.
Returning to the DRC state upon resume for seeking makes sure that the
client will get the DRC event and will reallocate the buffers to fit the
firmware's expectations.
Signed-off-by: Alexandre Courbot <acourbot@chromium.org>
Signed-off-by: Stanimir Varbanov <stanimir.varbanov@linaro.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
After adding more logic in vdec buf_queue vb2 op it is not
practical to have two lock/unlock for one decoder buf_queue.
So move the instance lock in encoder and decoder vb2 buf_queue
operations.
Signed-off-by: Stanimir Varbanov <stanimir.varbanov@linaro.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
This makes the decoder to behaives equally for sufficient and
insufficient events. After this change the LAST buffer flag will be set
when the new resolution (in dynamic-resolution-change state) is smaller
then the old bitstream resolution.
Signed-off-by: Stanimir Varbanov <stanimir.varbanov@linaro.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
In real use of dynamic-resolution-change it is observed that the
LAST buffer flag (which marks the last decoded buffer with the
resolution before the resolution-change event) is not reliably set.
Fix this by set the LAST buffer flag on next queued capture buffer
after the resolution-change event.
Signed-off-by: Stanimir Varbanov <stanimir.varbanov@linaro.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
This driver uses the SG vb2 ops, but effectively only ever accesses the
first entry of the SG table, indicating that it expects a flat layout.
Switch it to use the contiguous ops to make sure this expected invariant
is always enforced. Since the device is supposed to be behind an IOMMU
this should have little to none practical consequences beyond making the
driver not rely on a particular behavior of the SG implementation.
Reported-by: Tomasz Figa <tfiga@chromium.org>
Signed-off-by: Alexandre Courbot <acourbot@chromium.org>
Signed-off-by: Stanimir Varbanov <stanimir.varbanov@linaro.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Fix to return a negative error code from the error handling
case instead of 0, as done elsewhere in this function.
Fixes: d2b4387f3b ("media: platform: Add Aspeed Video Engine driver")
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Zhang Changzhong <zhangchangzhong@huawei.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
spinlock can be initialized automatically with DEFINE_SPINLOCK()
rather than explicitly calling spin_lock_init().
Signed-off-by: Zheng Yongjun <zhengyongjun3@huawei.com>
Reviewed-by: Lad Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
These entries can only ever be single bits. Make use of the BIT macro
accordingly.
Signed-off-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Implement the VIDIOC_SUBDEV_ENUM_FRAME_SIZE ioctl for the isp entity,
check if the mbus code is valid for the given pad.
This call is not available for the parameter or metadata pads of the
RkISP1.
Signed-off-by: Sebastian Fricke <sebastian.fricke.linux@gmail.com>
Acked-by: Dafna Hirschfeld <dafna.hirschfeld@collabora.com>
Acked-by: Helen Koike <helen.koike@collabora.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Since commit 4c62e9764a ("Drivers: media: remove __dev*
attributes.") in v3.8, the SuperH Video Output Unit driver no longer has
any code or data located in initmem, hence there is no need to annotate
the sh_vou structure with __refdata. Drop the annotation, to avoid
suppressing future section warnings.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
This error path returns success but it should return -EINVAL.
Fixes: cba3819d1e ("media: camss: Format configuration per hardware version")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Robert Foss <robert.foss@linaro.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
This test has a problem because we want to know if "k" is -1 or a
positive value less than "f->index". But the "f->index" variable is a
u32 so if "k == -1" then -1 gets type promoted to UINT_MAX which is
larger than "f->index". I've added an explicit test to check for -1.
Fixes: a3d412d4b9 ("media: Revert "media: camss: Make use of V4L2_CAP_IO_MC"")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Robert Foss <robert.foss@linaro.org>
Reviewed-by: Andrey Konovalov <andrey.konovalov@linaro.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Fix to return a negative error code from the error handling
case instead of 0, as done elsewhere in this function.
Fixes: dea42fb79f ("media: mtk-vcodec: reset segment data then trig decoder")
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Zhang Changzhong <zhangchangzhong@huawei.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
FIELD_GET() must only be used with a mask that is a compile-time
constant:
drivers/media/platform/ti-vpe/cal.h: In function 'cal_read_field':
include/linux/compiler_types.h:320:38: error: call to '__compiletime_assert_247' declared with attribute error: FIELD_GET: mask is not constant
include/linux/bitfield.h:46:3: note: in expansion of macro 'BUILD_BUG_ON_MSG'
46 | BUILD_BUG_ON_MSG(!__builtin_constant_p(_mask), \
| ^~~~~~~~~~~~~~~~
drivers/media/platform/ti-vpe/cal.h:220:9: note: in expansion of macro 'FIELD_GET'
220 | return FIELD_GET(mask, cal_read(cal, offset));
| ^~~~~~~~~
The problem here is that the function is not always inlined. Mark it
__always_inline to avoid the problem.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
It's the only user. This also garbage collects the CONFIG_FRAME_VECTOR
symbol from all over the tree (well just one place, somehow omap media
driver still had this in its Kconfig, despite not using it).
Reviewed-by: John Hubbard <jhubbard@nvidia.com>
Acked-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Acked-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Acked-by: Tomasz Figa <tfiga@chromium.org>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Cc: Jason Gunthorpe <jgg@ziepe.ca>
Cc: Pawel Osciak <pawel@osciak.com>
Cc: Marek Szyprowski <m.szyprowski@samsung.com>
Cc: Kyungmin Park <kyungmin.park@samsung.com>
Cc: Tomasz Figa <tfiga@chromium.org>
Cc: Mauro Carvalho Chehab <mchehab@kernel.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: John Hubbard <jhubbard@nvidia.com>
Cc: Jérôme Glisse <jglisse@redhat.com>
Cc: Jan Kara <jack@suse.cz>
Cc: Dan Williams <dan.j.williams@intel.com>
Cc: linux-mm@kvack.org
Cc: linux-arm-kernel@lists.infradead.org
Cc: linux-samsung-soc@vger.kernel.org
Cc: linux-media@vger.kernel.org
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/20201127164131.2244124-7-daniel.vetter@ffwll.ch
With TZ system reboot cannot finish successfully. To fix that
enable core clocks by runtime pm before TZ calls and disable
clocks after that.
Tested-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Stanimir Varbanov <stanimir.varbanov@linaro.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Currently the return error code is in ret is being assigned but not
used. It and should be returned by the return statement and currently
just 0 is being returned. Fix this.
Addresses-Coverity: ("Unused value")
Fixes: b9ad52aafe ("media: rcar-vin: Rework parallel firmware parsing")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The dst_handle field in the PUT_STREAM_BUFFER and ENCODE_FRAME_RESPONSE
is used to retrieve the V4L2 CAPTURE buffer. Calling it stream_id is
confusing. Call it dst_handle inspired by src_handle for the OUTPUT
buffer.
Signed-off-by: Michael Tretter <m.tretter@pengutronix.de>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The v4l2-m2m has various helpers for correctly handle the draining. Drop
the driver specific state machine and use the m2m helper functions.
Signed-off-by: Michael Tretter <m.tretter@pengutronix.de>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The stateful encoder API was finalized. Nothing is blocking the driver
from being moved out of staging.
Signed-off-by: Michael Tretter <m.tretter@pengutronix.de>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Rework the context API exposed to cal-video.c to simplify it. The
configuration and enable steps are all grouped in a single
cal_ctx_start() function, and the DMA stop and IRQ disable are similarly
groupd in cal_ctx_stop(). The cal_ctx_wr_dma_addr() function is renamed
to cal_ctx_set_dma_addr() for consistency with the cal_ctx_ prefix of
the start and stop functions.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Benoit Parrot <bparrot@ti.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Dikshita Agarwal