Add the support for enabling optional regulator that may be used as VCC
source.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
[Replaced 'error' variable with 'ret']
[Renamed regulator from 'vcc' to 'power']
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Reviewed-by: Biju Das <biju.das.jz@bp.renesas.com>
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20200922105526.5252-1-laurent.pinchart+renesas@ideasonboard.com
On some panels hooked up to the ti-sn65dsi86 bridge chip we found that
link training was failing. Specifically, we'd see:
ti_sn65dsi86 2-002d: [drm:ti_sn_bridge_enable] *ERROR* Link training failed, link is off (-5)
The panel was hooked up to a logic analyzer and it was found that, as
part of link training, the bridge chip was writing a 0x1 to DPCD
address 00600h and the panel responded NACK. As can be seen in header
files, the write of 0x1 to DPCD address 0x600h means we were trying to
write the value DP_SET_POWER_D0 to the register DP_SET_POWER. The
panel vendor says that a NACK in this case is not unexpected and means
"not ready, try again".
In testing, we found that this panel would respond with a NACK in
about 1/25 times. Adding the retry logic worked fine and the most
number of tries needed was 3. Just to be safe, we'll add 10 tries
here and we'll add a little blurb to the logs if we ever need more
than 5.
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Tested-By: Steev Klimaszewski <steev@kali.org>
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20201002135920.1.I2adbc90b2db127763e2444bd5a4e5bf30e1db8e5@changeid
This patch restores DRM connector registration in the TC358764 bridge
driver and restores usage of the old drm_panel_* API, thus allows dynamic
panel registration. This fixes panel operation on Exynos5250-based
Arndale board.
This is equivalent to the revert of the following commits:
1644127f83 "drm/bridge: tc358764: add drm_panel_bridge support"
385ca38da2 "drm/bridge: tc358764: drop drm_connector_(un)register"
and removal of the calls to drm_panel_attach()/drm_panel_detach(), which
were no-ops and has been removed in meanwhile.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200930114042.5806-1-m.szyprowski@samsung.com
The only usage of dw_hdmi_i2s_ops is to assign its address to the ops
field in the hdmi_codec_pdata struct, which is a const pointer. Make it
const to allow the compiler to put it in read-only memory.
Signed-off-by: Rikard Falkeborn <rikard.falkeborn@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/20201004200653.14702-1-rikard.falkeborn@gmail.com
On x64 we get:
drivers/gpu/drm/bridge/cadence/cdns-mhdp8546-core.c:751:10: warning: conversion from 'long unsigned int' to 'unsigned int' changes value from '18446744073709551613' to '4294967293' [-Woverflow]
The registers are 32 bit, so fix by casting to u32.
Fixes: fb43aa0acd ("drm: bridge: Add support for Cadence MHDP8546 DPI/DP bridge")
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Reviewed-by: Swapnil Jakhade <sjakhade@cadence.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/20200929091918.24813-1-tomi.valkeinen@ti.com
UAPI Changes:
Cross-subsystem Changes:
Core Changes:
- dev: More devm_drm convertions and removal of drm_dev_init
Driver Changes:
- i915: selftests improvements
- panfrost: support for Amlogic SoC
- vc4: one fix
-----BEGIN PGP SIGNATURE-----
iHUEABYIAB0WIQRcEzekXsqa64kGDp7j7w1vZxhRxQUCX2jGxQAKCRDj7w1vZxhR
xR3DAQCiZOnaxVcY49iG4343Z1aHHaIEShbnB0bDdaWstn7kiQD/UXBXUoOSFoFQ
FkTsW31JsdXNnWP5e6/eJd2Lb6waVAA=
=VlsU
-----END PGP SIGNATURE-----
Merge tag 'drm-misc-next-2020-09-21' of git://anongit.freedesktop.org/drm/drm-misc into drm-next
drm-misc-next for 5.10:
UAPI Changes:
Cross-subsystem Changes:
- virtio: Merged a PR for patches that will affect drm/virtio
Core Changes:
- dev: More devm_drm convertions and removal of drm_dev_init
- atomic: Split out drm_atomic_helper_calc_timestamping_constants of
drm_atomic_helper_update_legacy_modeset_state
- ttm: More rework
Driver Changes:
- i915: selftests improvements
- panfrost: support for Amlogic SoC
- vc4: one fix
- tree-wide: conversions to devm_drm_dev_alloc,
- ast: simplifications of the atomic modesetting code
- panfrost: multiple fixes
- vc4: multiple fixes
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Maxime Ripard <maxime@cerno.tech>
Link: https://patchwork.freedesktop.org/patch/msgid/20200921152956.2gxnsdgxmwhvjyut@gilmour.lan
Add the support for enabling optional regulator that may be used as VCC
source.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
[Replaced 'error' variable with 'ret']
[Renamed regulator from 'vcc' to 'power']
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Reviewed-by: Biju Das <biju.das.jz@bp.renesas.com>
Add J721E wrapper for mhdp, which sets up the clock and data muxes.
Signed-off-by: Jyri Sarha <jsarha@ti.com>
Signed-off-by: Yuti Amonkar <yamonkar@cadence.com>
Signed-off-by: Swapnil Jakhade <sjakhade@cadence.com>
Reviewed-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Add a new DRM bridge driver for Cadence MHDP8546 DPTX IP used in TI J721E
SoC. MHDP DPTX IP is the component that complies with VESA DisplayPort (DP)
and embedded Display Port (eDP) standards. It integrates uCPU running the
embedded Firmware (FW) interfaced over APB interface.
Basically, it takes a DPI stream as input and outputs it encoded in DP
format. Currently, it supports only SST mode.
Co-developed-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Co-developed-by: Jyri Sarha <jsarha@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Jyri Sarha <jsarha@ti.com>
Signed-off-by: Quentin Schulz <quentin.schulz@free-electrons.com>
Signed-off-by: Yuti Amonkar <yamonkar@cadence.com>
Signed-off-by: Swapnil Jakhade <sjakhade@cadence.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
The get_edid() callback can be triggered anytime by an ioctl, i.e
drm_mode_getconnector (ioctl)
-> drm_helper_probe_single_connector_modes
-> drm_bridge_connector_get_modes
-> ps8640_bridge_get_edid
Actually if the bridge pre_enable() function was not called before
get_edid(), the driver will not be able to get the EDID properly and
display will not work until a second get_edid() call is issued and if
pre_enable() is called before. The side effect of this, for example, is
that you see anything when `Frecon` starts, neither the splash screen,
until the graphical session manager starts.
To fix this we need to make sure that all we need is enabled before
reading the EDID. This means the following:
1. If get_edid() is called before having the device powered we need to
power on the device. In such case, the driver will power off again the
device.
2. If get_edid() is called after having the device powered, all should
just work. We added a powered flag in order to avoid recurrent calls
to ps8640_bridge_poweron() and unneeded delays.
3. This seems to be specific for this device, but we need to make sure
the panel is powered on before do a power on cycle on this device.
Otherwise the device fails to retrieve the EDID.
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Tested-by: Bilal Wasim <bwasim.lkml@gmail.com>
Acked-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200827085911.944899-2-enric.balletbo@collabora.com
kmemdup can be used instead of kmalloc+memcpy. Replace an occurrence of
this pattern.
Issue identified with Coccinelle.
Signed-off-by: Alex Dewar <alex.dewar90@gmail.com>
Acked-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200909190213.156302-1-alex.dewar90@gmail.com
UAPI Changes:
None
Cross-subsystem Changes:
* Moves a bunch of miscellaneous DP code from the i915 driver into a set
of shared DRM DP helpers
Core Changes:
* New DRM DP helpers (see above)
Driver Changes:
* Implements usage of the aforementioned DP helpers in the nouveau
driver, along with some other various HPD related cleanup for nouveau
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Lyude Paul <lyude@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/11e59ebdea7ee4f46803a21fe9b21443d2b9c401.camel@redhat.com
This fixes the following warnings while building in W=1 :
dw-mipi-dsi.c:1002:5: warning: no previous prototype for 'dw_mipi_dsi_debugfs_write' [-Wmissing-prototypes]
dw-mipi-dsi.c:1027:5: warning: no previous prototype for 'dw_mipi_dsi_debugfs_show' [-Wmissing-prototypes]
Fixes: e2435d6920 ("drm/bridge: dw-mipi-dsi.c: Add VPG runtime config through debugfs")
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Angelo Ribeiro <angelo.ribeiro@synopsys.com>
Cc: Maxime Ripard <maxime@cerno.tech>
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Cc: Thomas Zimmermann <tzimmermann@suse.de>
Link: https://patchwork.freedesktop.org/patch/msgid/20200907102711.23748-1-narmstrong@baylibre.com
-----BEGIN PGP SIGNATURE-----
iQFSBAABCAA8FiEEq68RxlopcLEwq+PEeb4+QwBBGIYFAl9VerweHHRvcnZhbGRz
QGxpbnV4LWZvdW5kYXRpb24ub3JnAAoJEHm+PkMAQRiGhc4H/iHD6qLdB36gZB6K
oc2nJyrqyWitv4ti2Mnt5PA7o4wX4l6nnr1QvoaJ4BRs5Ja1czRvb2XDmdzqAoIA
xITGoafqaAeDfxQ91bWrJsVN0pCRKiGwddXlU7TWmqw/riAkfOqi6GYKvav4biJH
+n1mUPQb1M2IbRFsqkAS+ebKHq3CWaRvzKOEneS88nGlL5u31S9NAru8Ru/fkxRn
6CwGcs1XRaBPYaZAhdfIb0NuatUlpkhPC9yhNS9up6SqrWmK3m65vmFVng6H0eCF
fwn1jVztboY/XcNAi5sM9ExpQCql6WLQEEktVikqRDojC8fVtSx6W55tPt7qeaoO
Z6t4/DA=
=bcA4
-----END PGP SIGNATURE-----
Merge tag 'v5.9-rc4' into drm-next
Backmerge 5.9-rc4 as there is a nasty qxl conflict
that needs to be resolved.
Signed-off-by: Dave Airlie <airlied@redhat.com>
Add support for the video pattern generator (VPG) BER pattern mode and
configuration in runtime.
This enables using the debugfs interface to manipulate the VPG after
the pipeline is set.
Also, enables the usage of the VPG BER pattern.
Changes in v2:
- Added VID_MODE_VPG_MODE
- Solved incompatible return type on __get and __set
Reported-by: kbuild test robot <lkp@intel.com>
Reported-by: Adrian Pop <pop.adrian61@gmail.com>
Signed-off-by: Angelo Ribeiro <angelo.ribeiro@synopsys.com>
Tested-by: Yannick Fertre <yannick.fertre@st.com>
Tested-by: Adrian Pop <pop.adrian61@gmail.com>
Acked-by: Neil Armstrong <narmstrong@baylibre.com>
Cc: Gustavo Pimentel <gustavo.pimentel@synopsys.com>
Cc: Joao Pinto <jpinto@synopsys.com>
Cc: Jose Abreu <jose.abreu@synopsys.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Link: https://patchwork.freedesktop.org/patch/msgid/a809feb7d7153a92e323416f744f1565e995da01.1586180592.git.angelo.ribeiro@synopsys.com
Current code enables the HS clock when video mode is started or to
send out a HS command, and disables the HS clock to send out a LP
command. This is not what DSI spec specify.
Enable HS clock either in command and in video mode.
Set automatic HS clock management for panels and devices that
support non-continuous HS clock.
Signed-off-by: Antonio Borneo <antonio.borneo@st.com>
Tested-by: Philippe Cornu <philippe.cornu@st.com>
Reviewed-by: Philippe Cornu <philippe.cornu@st.com>
Acked-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200701194234.18123-1-yannick.fertre@st.com
Current code does not properly computes the max length of LP
commands that can be send during H or V sync, and rely on static
values.
Limiting the max LP length to 4 byte during the V-sync is overly
conservative.
Relax the limit and allows longer LP commands (16 bytes) to be
sent during V-sync.
Signed-off-by: Antonio Borneo <antonio.borneo@st.com>
Tested-by: Philippe Cornu <philippe.cornu@st.com>
Reviewed-by: Philippe Cornu <philippe.cornu@st.com>
Acked-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200701143131.841-1-yannick.fertre@st.com
Current code only sends LP commands in command mode.
Allows sending LP commands also in video mode by setting the
proper flag in DSI_VID_MODE_CFG.
Signed-off-by: Antonio Borneo <antonio.borneo@st.com>
Tested-by: Philippe Cornu <philippe.cornu@st.com>
Reviewed-by: Philippe Cornu <philippe.cornu@st.com>
Acked-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200708140836.32418-1-yannick.fertre@st.com
DSI end-points are supposed to be at node 0 and node 1 as per binding.
So fix this and use node 0 and node 1 for dsi.
Reported-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Fixes: 23278bf54a ("drm/bridge: Introduce LT9611 DSI to HDMI bridge")
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20200828074251.3788165-1-vkoul@kernel.org
Print an error message inside ps8640_bridge_vdo_control() function when
it fails so we can simplify a bit the callers, they will only need to
check the error code.
Reviewed-by: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Reviewed-by: Bilal Wasim <bwasim.lkml@gmail.com>
Tested-by: Bilal Wasim <bwasim.lkml@gmail.com>
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20200826081526.674866-5-enric.balletbo@collabora.com
Bridge drivers that implement the new model only shall return an error
from their attach() handler when the DRM_BRIDGE_ATTACH_NO_CONNECTOR flag
is not set. So make sure we return an error because only the new
drm_bridge model is supported.
Reviewed-by: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Reviewed-by: Bilal Wasim <bwasim.lkml@gmail.com>
Tested-by: Bilal Wasim <bwasim.lkml@gmail.com>
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20200826081526.674866-4-enric.balletbo@collabora.com
The PS8640 DSI-to-eDP bridge can retrieve the EDID, so implement the
.get_edid callback and set the flag to indicate the core to use it.
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20200826081526.674866-3-enric.balletbo@collabora.com
If ge_b850v3_lvds_init() does not allocate memory for ge_b850v3_lvds_ptr,
then a null pointer dereference is accessed.
The patch adds checking of the return value of ge_b850v3_lvds_init().
Found by Linux Driver Verification project (linuxtesting.org).
Signed-off-by: Nadezda Lutovinova <lutovinova@ispras.ru>
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20200819143756.30626-1-lutovinova@ispras.ru
Add very basic driver for Toshiba TC358762 DSI-to-DPI bridge, derived
from tc358764 driver and panel-raspberrypi-touchscreen. This driver is
meant to replace the panel-raspberrypi-touchscreen too, as the bridge
connection can be described in DT too.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: dri-devel@lists.freedesktop.org
Cc: Eric Anholt <eric@anholt.net>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Sam Ravnborg <sam@ravnborg.org>
Cc: devicetree@vger.kernel.org
Reviewed-by: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: Sam Ravnborg <sam.ravnborg@gmail.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200809105705.6334-2-marex@denx.de
Backmerging drm-next into drm-misc-next for nouveau and panel updates.
Resolves a conflict between ttm and nouveau, where struct ttm_mem_res got
renamed to struct ttm_resource.
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
-----BEGIN PGP SIGNATURE-----
iQFSBAABCAA8FiEEq68RxlopcLEwq+PEeb4+QwBBGIYFAl8nLmkeHHRvcnZhbGRz
QGxpbnV4LWZvdW5kYXRpb24ub3JnAAoJEHm+PkMAQRiGBEkH/RJAnEan4gcdkBDf
2xS0yk4XLMjKZwbz61VSeKMUBkGCsh1cWsaAtJJAIVYj/6o/7mld01sZCnOASLnJ
ET0nXL2NiT/f+prYkTE5qeYH225/Yfh5jgmrqZtx/uXFCwgE5Nzi3f72IXQDmCR+
kmpNhNox3YqQTKXhv7DXobDKcO0n8nZavnhxmA9SBZn2h9RHvmvJghD0UOfLjMpA
1SbknaE67n5JN/JjI6TkYWk4nuJmqfvmBL5IYVDEZYO4UlM5Bqzhw0XN7Ax70K3M
KRK/eiqRmNwun5MxWnbzQU7t7iTgVmzjHLTpWGcM3V4blgGXC3uhjc+p/R8KTQUE
bIydSzs=
=fDeo
-----END PGP SIGNATURE-----
Merge tag 'v5.8' into drm-next
I need to backmerge 5.8 as I've got a bunch of fixes sitting
on an rc7 base that I want to land.
Signed-off-by: Dave Airlie <airlied@redhat.com>
This driver is tested with two panels individually with Apq8016-IFC6309 board
https://www.inforcecomputing.com/products/single-board-computers-sbc/qualcomm-snapdragon-410-inforce-6309-micro-sbc
1. 1366x768@60 auo,b101xtn01 data-mapping = "jeida-24"
2. 800x480@60 innolux,at070tn92 data-mapping = "vesa-24"
- power off sequence in proper order
- put_unaligned_be16, put_unaligned_le32 macros used
- static function for mode_valid
- len initialized
- MODE_CLOCK_HIGH handled properly
- bus_formats handled in mode_valid
- GENMASK and FIELD_PREP used
- Kconfig proper indentation
- error handling endpoint data-lanes
- check for bus_formats unsupported
- display_timings naming local variables
- help modified
- ~vsdelay dynamic value set based on the
calculation of dsi speed, output speed, blanking
- panel->connector_type removed
- dual port implemented
- devm_drm_panel_bridge_add method used instead of panel
description modified
- regulator enable and disable with proper orders and delays
as per the spec
- removed drm_connector_status
- added bus_formats
- mdelay to usleep_range
- magic number to macros for CLRSI and mux registers
description modified
- replaced u32 instead of uint32_t
- updated alphabetic order of headers
- added SPDX identifier license
Signed-off-by: Vinay Simha BN <simhavcs@gmail.com>
Reviewed-by: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: Sam Ravnborg <sam.ravnborg@gmail.com>
Link: https://patchwork.freedesktop.org/patch/msgid/1594388491-15129-2-git-send-email-simhavcs@gmail.com
These functions are now empty and no longer
useful so remove the functions and their uses.
Signed-off-by: Joe Perches <joe@perches.com>
Cc: Bernard Zhao <bernard@vivo.com>
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Cc: Maxime Ripard <mripard@kernel.org>,
Cc: Thomas Zimmermann <tzimmermann@suse.de>
Cc: Thierry Reding <thierry.reding@gmail.com>
Cc: David Airlie <airlied@linux.ie>
Cc: Daniel Vetter <daniel@ffwll.ch>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Icenowy Zheng <icenowy@aosc.io>,
Cc: Jagan Teki <jagan@amarulasolutions.com>
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: Robert Chiras <robert.chiras@nxp.com>
Cc: dri-devel@lists.freedesktop.org,
Cc: linux-kernel@vger.kernel.org
Cc: opensource.kernel@vivo.com
Signed-off-by: Sam Ravnborg <sam@ravnborg.org> # Fixed build and a few warnings
Link: https://patchwork.freedesktop.org/patch/msgid/9e13761020750b1ce2f1fabee23ef6e2a2942882.camel@perches.com
This became wide and scattered updates all over the sound tree as
diffstat shows: lots of (still ongoing) refactoring works in ASoC,
fixes and cleanups caught by static analysis, inclusive term
conversions as well as lots of new drivers. Below are highlights:
ASoC core:
* API cleanups and conversions to the unified mute_stream() call
* Simplify I/O helper functions
* Use helper macros to retrieve RTD from substreams
ASoC drivers:
* Lots of fixes and cleanups in Intel ASoC drivers
* Lots of new stuff: Freescale MQS and i.MX6sx, Intel KeemBay I2S,
Maxim MAX98360A and MAX98373 SoundWire, various Mediatek boards,
nVidia Tegra 186 and 210, RealTek RL6231, Samsung Midas and Aries
boards, TI J721e EVM
ALSA core:
* Minor code refacotring for SG-buffer handling
HD-audio:
* Generalization of mute-LED handling with LED classdev
* Intel silent stream support for HDMI
* Device-specific fixes: CA0132, Loongson-3
Others:
* Usual USB- and HD-audio quirks for various devices
* Fixes for echoaudio DMA position handling
* Various documents and trivial fixes for sparse warnings
* Conversion to adapt inclusive terms
-----BEGIN PGP SIGNATURE-----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=sy7n
-----END PGP SIGNATURE-----
Merge tag 'sound-5.9-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull sound updates from Takashi Iwai:
"This became wide and scattered updates all over the sound tree as
diffstat shows: lots of (still ongoing) refactoring works in ASoC,
fixes and cleanups caught by static analysis, inclusive term
conversions as well as lots of new drivers. Below are highlights:
ASoC core:
- API cleanups and conversions to the unified mute_stream() call
- Simplify I/O helper functions
- Use helper macros to retrieve RTD from substreams
ASoC drivers:
- Lots of fixes and cleanups in Intel ASoC drivers
- Lots of new stuff: Freescale MQS and i.MX6sx, Intel KeemBay I2S,
Maxim MAX98360A and MAX98373 SoundWire, various Mediatek boards,
nVidia Tegra 186 and 210, RealTek RL6231, Samsung Midas and Aries
boards, TI J721e EVM
ALSA core:
- Minor code refacotring for SG-buffer handling
HD-audio:
- Generalization of mute-LED handling with LED classdev
- Intel silent stream support for HDMI
- Device-specific fixes: CA0132, Loongson-3
Others:
- Usual USB- and HD-audio quirks for various devices
- Fixes for echoaudio DMA position handling
- Various documents and trivial fixes for sparse warnings
- Conversion to adopt inclusive terms"
* tag 'sound-5.9-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound: (479 commits)
ALSA: pci: delete repeated words in comments
ALSA: isa: delete repeated words in comments
ALSA: hda/tegra: Add 100us dma stop delay
ALSA: hda: Add dma stop delay variable
ASoC: hda/tegra: Set buffer alignment to 128 bytes
ALSA: seq: oss: Serialize ioctls
ALSA: hda/hdmi: Add quirk to force connectivity
ALSA: usb-audio: add startech usb audio dock name
ALSA: usb-audio: Add support for Lenovo ThinkStation P620
Revert "ALSA: hda: call runtime_allow() for all hda controllers"
ALSA: hda/ca0132 - Fix AE-5 microphone selection commands.
ALSA: hda/ca0132 - Add new quirk ID for Recon3D.
ALSA: hda/ca0132 - Fix ZxR Headphone gain control get value.
ALSA: hda/realtek: Add alc269/alc662 pin-tables for Loongson-3 laptops
ALSA: docs: fix typo
ALSA: doc: use correct config variable name
ASoC: core: Two step component registration
ASoC: core: Simplify snd_soc_component_initialize declaration
ASoC: core: Relocate and expose snd_soc_component_initialize
ASoC: sh: Replace 'select' DMADEVICES 'with depends on'
...
core:
- add user def flag to cmd line modes
- dma_fence_wait added might_sleep
- dma-fence lockdep annotations
- indefinite fences are bad documentation
- gem CMA functions used in more drivers
- struct mutex removal
- more drm_ debug macro usage
- set/drop master api fixes
- fix for drm/mm hole size comparison
- drm/mm remove invalid entry optimization
- optimise drm/mm hole handling
- VRR debugfs added
- uncompressed AFBC modifier support
- multiple display id blocks in EDID
- multiple driver sg handling fixes
- __drm_atomic_helper_crtc_reset in all drivers
- managed vram helpers
ttm:
- ttm_mem_reg handling cleanup
- remove bo offset field
- drop CMA memtype flag
- drop mappable flag
xilinx:
- New Xilinx ZynqMP DisplayPort Subsystem driver
nouveau:
- add CRC support
- start using NVIDIA published class header files
- convert all push buffer emission to new macros
- Proper push buffer space management for EVO/NVD channels.
- firmware loading fixes
- 2MiB system memory pages support on Pascal and newer
vkms:
- larget cursor support
i915:
- Rocketlake platform enablement
- Early DG1 enablement
- Numerous GEM refactorings
- DP MST fixes
- FBC, PSR, Cursor, Color, Gamma fixes
- TGL, RKL, EHL workaround updates
- TGL 8K display support fixes
- SDVO/HDMI/DVI fixes
amdgpu:
- Initial support for Sienna Cichlid GPU
- Initial support for Navy Flounder GPU
- SI UVD/VCE support
- expose rotation property
- Add support for unique id on Arcturus
- Enable runtime PM on vega10 boards that support BACO
- Skip BAR resizing if the bios already did id
- Major swSMU code cleanup
- Fixes for DCN bandwidth calculations
amdkfd:
- Track SDMA usage per process
- SMI events interface
radeon:
- Default to on chip GART for AGP boards on all arches
- Runtime PM reference count fixes
msm:
- headers regenerated causing churn
- a650/a640 display and GPU enablement
- dpu dither support for 6bpc panels
- dpu cursor fix
- dsi/mdp5 enablement for sdm630/sdm636/sdm66
tegra:
- video capture prep support
- reflection support
mediatek:
- convert mtk_dsi to bridge API
meson:
- FBC support
sun4i:
- iommu support
rockchip:
- register locking fix
- per-pixel alpha support PX30 VOP
-
mgag200:
- ported to simple and shmem helpers
- device init cleanups
- use managed pci functions
- dropped hw cursor support
ast:
- use managed pci functions
- use managed VRAM helpers
- rework cursor support
malidp:
- dev_groups support
hibmc:
- refactor hibmc_drv_vdac:
vc4:
- create TXP CRTC
imx:
- error path fixes and cleanups
etnaviv:
- clock handling and error handling cleanups
- use pin_user_pages
-----BEGIN PGP SIGNATURE-----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=Yvtd
-----END PGP SIGNATURE-----
Merge tag 'drm-next-2020-08-06' of git://anongit.freedesktop.org/drm/drm
Pull drm updates from Dave Airlie:
"New xilinx displayport driver, AMD support for two new GPUs (more
header files), i915 initial support for RocketLake and some work on
their DG1 (discrete chip).
The core also grew some lockdep annotations to try and constrain what
drivers do with dma-fences, and added some documentation on why the
idea of indefinite fences doesn't work.
The long list is below.
I do have some fixes trees outstanding, but I'll follow up with those
later.
core:
- add user def flag to cmd line modes
- dma_fence_wait added might_sleep
- dma-fence lockdep annotations
- indefinite fences are bad documentation
- gem CMA functions used in more drivers
- struct mutex removal
- more drm_ debug macro usage
- set/drop master api fixes
- fix for drm/mm hole size comparison
- drm/mm remove invalid entry optimization
- optimise drm/mm hole handling
- VRR debugfs added
- uncompressed AFBC modifier support
- multiple display id blocks in EDID
- multiple driver sg handling fixes
- __drm_atomic_helper_crtc_reset in all drivers
- managed vram helpers
ttm:
- ttm_mem_reg handling cleanup
- remove bo offset field
- drop CMA memtype flag
- drop mappable flag
xilinx:
- New Xilinx ZynqMP DisplayPort Subsystem driver
nouveau:
- add CRC support
- start using NVIDIA published class header files
- convert all push buffer emission to new macros
- Proper push buffer space management for EVO/NVD channels.
- firmware loading fixes
- 2MiB system memory pages support on Pascal and newer
vkms:
- larger cursor support
i915:
- Rocketlake platform enablement
- Early DG1 enablement
- Numerous GEM refactorings
- DP MST fixes
- FBC, PSR, Cursor, Color, Gamma fixes
- TGL, RKL, EHL workaround updates
- TGL 8K display support fixes
- SDVO/HDMI/DVI fixes
amdgpu:
- Initial support for Sienna Cichlid GPU
- Initial support for Navy Flounder GPU
- SI UVD/VCE support
- expose rotation property
- Add support for unique id on Arcturus
- Enable runtime PM on vega10 boards that support BACO
- Skip BAR resizing if the bios already did id
- Major swSMU code cleanup
- Fixes for DCN bandwidth calculations
amdkfd:
- Track SDMA usage per process
- SMI events interface
radeon:
- Default to on chip GART for AGP boards on all arches
- Runtime PM reference count fixes
msm:
- headers regenerated causing churn
- a650/a640 display and GPU enablement
- dpu dither support for 6bpc panels
- dpu cursor fix
- dsi/mdp5 enablement for sdm630/sdm636/sdm66
tegra:
- video capture prep support
- reflection support
mediatek:
- convert mtk_dsi to bridge API
meson:
- FBC support
sun4i:
- iommu support
rockchip:
- register locking fix
- per-pixel alpha support PX30 VOP
mgag200:
- ported to simple and shmem helpers
- device init cleanups
- use managed pci functions
- dropped hw cursor support
ast:
- use managed pci functions
- use managed VRAM helpers
- rework cursor support
malidp:
- dev_groups support
hibmc:
- refactor hibmc_drv_vdac:
vc4:
- create TXP CRTC
imx:
- error path fixes and cleanups
etnaviv:
- clock handling and error handling cleanups
- use pin_user_pages"
* tag 'drm-next-2020-08-06' of git://anongit.freedesktop.org/drm/drm: (1747 commits)
drm/msm: use kthread_create_worker instead of kthread_run
drm/msm/mdp5: Add MDP5 configuration for SDM636/660
drm/msm/dsi: Add DSI configuration for SDM660
drm/msm/mdp5: Add MDP5 configuration for SDM630
drm/msm/dsi: Add phy configuration for SDM630/636/660
drm/msm/a6xx: add A640/A650 hwcg
drm/msm/a6xx: hwcg tables in gpulist
drm/msm/dpu: add SM8250 to hw catalog
drm/msm/dpu: add SM8150 to hw catalog
drm/msm/dpu: intf timing path for displayport
drm/msm/dpu: set missing flush bits for INTF_2 and INTF_3
drm/msm/dpu: don't use INTF_INPUT_CTRL feature on sdm845
drm/msm/dpu: move some sspp caps to dpu_caps
drm/msm/dpu: update UBWC config for sm8150 and sm8250
drm/msm/dpu: use right setup_blend_config for sm8150 and sm8250
drm/msm/a6xx: set ubwc config for A640 and A650
drm/msm/adreno: un-open-code some packets
drm/msm: sync generated headers
drm/msm/a6xx: add build_bw_table for A640/A650
drm/msm/a6xx: fix crashstate capture for A650
...
Here is the "big" set of changes to the driver core, and some drivers
using the changes, for 5.9-rc1.
"Biggest" thing in here is the device link exposure in sysfs, to help
to tame the madness that is SoC device tree representations and driver
interactions with it.
Other stuff in here that is interesting is:
- device probe log helper so that drivers can report problems in
a unified way easier.
- devres functions added
- DEVICE_ATTR_ADMIN_* macro added to make it harder to write
incorrect sysfs file permissions
- documentation cleanups
- ability for debugfs to be present in the kernel, yet not
exposed to userspace. Needed for systems that want it
enabled, but do not trust users, so they can still use some
kernel functions that were otherwise disabled.
- other minor fixes and cleanups
The patches outside of drivers/base/ all have acks from the respective
subsystem maintainers to go through this tree instead of theirs.
All of these have been in linux-next with no reported issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCXylhOQ8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ylGdACeKqxm8IIDZycj0QjLUlPiEwVIROgAnjpf5jAB
mb4jMvgEGsB6/FwxypPG
=RUss
-----END PGP SIGNATURE-----
Merge tag 'driver-core-5.9-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull driver core updates from Greg KH:
"Here is the "big" set of changes to the driver core, and some drivers
using the changes, for 5.9-rc1.
"Biggest" thing in here is the device link exposure in sysfs, to help
to tame the madness that is SoC device tree representations and driver
interactions with it.
Other stuff in here that is interesting is:
- device probe log helper so that drivers can report problems in a
unified way easier.
- devres functions added
- DEVICE_ATTR_ADMIN_* macro added to make it harder to write
incorrect sysfs file permissions
- documentation cleanups
- ability for debugfs to be present in the kernel, yet not exposed to
userspace. Needed for systems that want it enabled, but do not
trust users, so they can still use some kernel functions that were
otherwise disabled.
- other minor fixes and cleanups
The patches outside of drivers/base/ all have acks from the respective
subsystem maintainers to go through this tree instead of theirs.
All of these have been in linux-next with no reported issues"
* tag 'driver-core-5.9-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core: (39 commits)
drm/bridge: lvds-codec: simplify error handling
drm/bridge/sii8620: fix resource acquisition error handling
driver core: add deferring probe reason to devices_deferred property
driver core: add device probe log helper
driver core: Avoid binding drivers to dead devices
Revert "test_firmware: Test platform fw loading on non-EFI systems"
firmware_loader: EFI firmware loader must handle pre-allocated buffer
selftest/firmware: Add selftest timeout in settings
test_firmware: Test platform fw loading on non-EFI systems
driver core: Change delimiter in devlink device's name to "--"
debugfs: Add access restriction option
tracefs: Remove unnecessary debug_fs checks.
driver core: Fix probe_count imbalance in really_probe()
kobject: remove unused KOBJ_MAX action
driver core: Fix sleeping in invalid context during device link deletion
driver core: Add waiting_for_supplier sysfs file for devices
driver core: Add state_synced sysfs file for devices that support it
driver core: Expose device link details in sysfs
driver core: Drop mention of obsolete bus rwsem from kernel-doc
debugfs: file: Remove unnecessary cast in kfree()
...
Using dev_err_probe code has following advantages:
- shorter code,
- recorded defer probe reason for debugging,
- uniform error code logging.
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Link: https://lore.kernel.org/r/20200713144324.23654-5-a.hajda@samsung.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In case of error during resource acquisition driver should print error
message only in case it is not deferred probe, using dev_err_probe helper
solves the issue. Moreover it records defer probe reason for debugging.
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Link: https://lore.kernel.org/r/20200713144324.23654-4-a.hajda@samsung.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Prepare the bridge driver for use in a chained setup.
- Replacing direct use of drm_panel with drm_panel_bridge support.
- Make the connector creation optional
Note: the bridge panel will use the connector type from the panel.
v3:
- Fix wrong logic in connector creation (Laurent)
v2:
- Use panel_bridge for local variable name to align with other drivers
- Fix that connector was created twice (Laurent)
- Set bridge.type to DRM_MODE_CONNECTOR_LVDS.
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: Andrzej Hajda <a.hajda@samsung.com>
Cc: Neil Armstrong <narmstrong@baylibre.com>
Cc: Laurent Pinchart <Laurent.pinchart@ideasonboard.com>
Cc: Jonas Karlman <jonas@kwiboo.se>
Cc: Jernej Skrabec <jernej.skrabec@siol.net>
Link: https://patchwork.freedesktop.org/patch/msgid/20200727170320.959777-6-sam@ravnborg.org
Add the get_edid() bridge operation to prepare for
use as a chained bridge.
Add helper function that is also used by the connector.
v2:
- Fix memory leak (Laurent)
- Do not save a copy of edid, read it when needed
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: Andrzej Hajda <a.hajda@samsung.com>
Cc: Neil Armstrong <narmstrong@baylibre.com>
Cc: Laurent Pinchart <Laurent.pinchart@ideasonboard.com>
Cc: Jonas Karlman <jonas@kwiboo.se>
Cc: Jernej Skrabec <jernej.skrabec@siol.net>
Link: https://patchwork.freedesktop.org/patch/msgid/20200727170320.959777-5-sam@ravnborg.org
With the bridge operations implemented the last step to prepare
this driver for a chained setup is the use of the bridge panel driver.
The bridge panel driver is only used when a port@2 is present in
the DT. So when the display driver requests a connector
support both situations:
- connector created by bridge panel driver
- connector created by this driver
And on top, support that the display driver creates the connector,
which is the preferred setup.
Note: the bridge panel will use the connector type from the panel.
v3:
- Fix wrong logic in connector creation (Laurent)
v2:
- Merge connector and drm_panel_bridge patches
and fix so we do not create two connectors (Laurent)
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: Andrzej Hajda <a.hajda@samsung.com>
Cc: Neil Armstrong <narmstrong@baylibre.com>
Cc: Jonas Karlman <jonas@kwiboo.se>
Cc: Jernej Skrabec <jernej.skrabec@siol.net>
Link: https://patchwork.freedesktop.org/patch/msgid/20200727170320.959777-4-sam@ravnborg.org
Prepare the bridge driver for chained operation by adding
support for the detect operation.
v3:
- Fix code to make it readable (Laurent)
v2:
- Do not announce detect operation if there is no hpd pin (Laurent)
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: Andrzej Hajda <a.hajda@samsung.com>
Cc: Neil Armstrong <narmstrong@baylibre.com>
Cc: Laurent Pinchart <Laurent.pinchart@ideasonboard.com>
Cc: Jonas Karlman <jonas@kwiboo.se>
Cc: Jernej Skrabec <jernej.skrabec@siol.net>
Link: https://patchwork.freedesktop.org/patch/msgid/20200727170320.959777-2-sam@ravnborg.org
Make the connector creation optional to enable usage of the
megachips-stdpxxxx-ge-b850v3-fw bridge with the DRM bridge connector
helper.
v2:
- Set bridge.type to DRM_MODE_CONNECTOR_DisplayPort
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: Peter Senna Tschudin <peter.senna@gmail.com>
Cc: Martin Donnelly <martin.donnelly@ge.com>
Cc: Martyn Welch <martyn.welch@collabora.co.uk>
Cc: Andrzej Hajda <a.hajda@samsung.com>
Cc: Neil Armstrong <narmstrong@baylibre.com>
Cc: Laurent Pinchart <Laurent.pinchart@ideasonboard.com>
Cc: Jonas Karlman <jonas@kwiboo.se>
Cc: Jernej Skrabec <jernej.skrabec@siol.net>
Link: https://patchwork.freedesktop.org/patch/msgid/20200726203324.3722593-14-sam@ravnborg.org
To prepare for a chained bridge setup add support for the
get_edid bridge operation.
There is no need for a copy of the edid - so drop
the pointer to the copy.
v2:
- Fix so we do not leak memory (Laurent)
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: Peter Senna Tschudin <peter.senna@gmail.com>
Cc: Martin Donnelly <martin.donnelly@ge.com>
Cc: Martyn Welch <martyn.welch@collabora.co.uk>
Cc: Andrzej Hajda <a.hajda@samsung.com>
Cc: Neil Armstrong <narmstrong@baylibre.com>
Cc: Laurent Pinchart <Laurent.pinchart@ideasonboard.com>
Cc: Jonas Karlman <jonas@kwiboo.se>
Cc: Jernej Skrabec <jernej.skrabec@siol.net>
Link: https://patchwork.freedesktop.org/patch/msgid/20200726203324.3722593-13-sam@ravnborg.org
To prepare for use in a chained bridge setup enable the
detect operation.
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: Peter Senna Tschudin <peter.senna@gmail.com>
Cc: Martin Donnelly <martin.donnelly@ge.com>
Cc: Martyn Welch <martyn.welch@collabora.co.uk>
Cc: Andrzej Hajda <a.hajda@samsung.com>
Cc: Neil Armstrong <narmstrong@baylibre.com>
Cc: Laurent Pinchart <Laurent.pinchart@ideasonboard.com>
Cc: Jonas Karlman <jonas@kwiboo.se>
Cc: Jernej Skrabec <jernej.skrabec@siol.net>
Link: https://patchwork.freedesktop.org/patch/msgid/20200726203324.3722593-12-sam@ravnborg.org
Fix so drm_device is read from the bridge.
This is a preparation for the connector being optional.
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: Peter Senna Tschudin <peter.senna@gmail.com>
Cc: Martin Donnelly <martin.donnelly@ge.com>
Cc: Martyn Welch <martyn.welch@collabora.co.uk>
Cc: Andrzej Hajda <a.hajda@samsung.com>
Cc: Neil Armstrong <narmstrong@baylibre.com>
Cc: Laurent Pinchart <Laurent.pinchart@ideasonboard.com>
Cc: Jonas Karlman <jonas@kwiboo.se>
Cc: Jernej Skrabec <jernej.skrabec@siol.net>
Link: https://patchwork.freedesktop.org/patch/msgid/20200726203324.3722593-11-sam@ravnborg.org
Prepare the bridge driver for use in a chained setup by
replacing direct use of drm_panel with drm_panel_bridge support.
The connecter is now either created by the panel bridge or the display
driver. So all code for connector creation in this driver is no longer
relevant and thus dropped.
The connector code had some special polling handling:
connector.polled = DRM_CONNECTOR_POLL_HPD;
drm_helper_hpd_irq_event(ps8622->bridge.dev);
This code was most likely added to speed up detection of the connector.
If really needed then this functionality belongs somewhere else.
Note: the bridge panel will use the connector type from the panel.
v2:
- Fix to avoid creating connector twice (Laurent)
- Drop all connector code - defer to bridge panel
- Use panel_bridge for local variable to align with other drivers
- Set bridge.type to DRM_MODE_CONNECTOR_LVDS;
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: Andrzej Hajda <a.hajda@samsung.com>
Cc: Neil Armstrong <narmstrong@baylibre.com>
Cc: Laurent Pinchart <Laurent.pinchart@ideasonboard.com>
Cc: Jonas Karlman <jonas@kwiboo.se>
Cc: Jernej Skrabec <jernej.skrabec@siol.net>
Link: https://patchwork.freedesktop.org/patch/msgid/20200726203324.3722593-9-sam@ravnborg.org
Prepare the tc358764 bridge driver for use in a chained setup by
replacing direct use of drm_panel with drm_panel_bridge support.
The bridge panel will use the connector type reported by the panel,
where the connector for this driver hardcodes DRM_MODE_CONNECTOR_LVDS.
The tc358764 did not add any additional info the the connector so the
connector creation is passed to the bridge panel driver.
v3:
- Merge with patch to make connector creation optional to avoid
creating two connectors (Laurent)
- Pass connector creation to bridge panel, as this bridge driver
did not add any extra info to the connector.
- Set bridge.type to DRM_MODE_CONNECTOR_LVDS.
v2:
- Use PTR_ERR_OR_ZERO() (kbuild test robot)
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: kbuild test robot <lkp@intel.com>
Cc: Andrzej Hajda <a.hajda@samsung.com>
Cc: Neil Armstrong <narmstrong@baylibre.com>
Cc: Jonas Karlman <jonas@kwiboo.se>
Cc: Jernej Skrabec <jernej.skrabec@siol.net>
Link: https://patchwork.freedesktop.org/patch/msgid/20200726203324.3722593-5-sam@ravnborg.org
Drop drm_connector handling that is not needed:
- drm_dev_register() in the display controller driver takes
care of registering connectors.
So the call to drm_connector_register() call is not needed in the bridge
driver.
- Use of drm_connector_unregister() is only required for drivers that
explicit have called drm_dev_register.
- The reference counting using drm_connector_put() is likewise not needed.
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: Andrzej Hajda <a.hajda@samsung.com>
Cc: Neil Armstrong <narmstrong@baylibre.com>
Cc: Laurent Pinchart <Laurent.pinchart@ideasonboard.com>
Cc: Jonas Karlman <jonas@kwiboo.se>
Cc: Jernej Skrabec <jernej.skrabec@siol.net>
Link: https://patchwork.freedesktop.org/patch/msgid/20200726203324.3722593-4-sam@ravnborg.org
After the drm_bridge_connector_init() helper function has been added,
the ADV driver has been changed accordingly. However, the 'type'
field of the bridge structure was left unset, which makes the helper
function always return -EINVAL.
Signed-off-by: Laurentiu Palcu <laurentiu.palcu@nxp.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Vinod Koul <vkoul@kernel.org>
Tested-by: Vinod Koul <vkoul@kernel.org> # tested on DragonBoard 410c
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20200720124228.12552-1-laurentiu.palcu@oss.nxp.com
Lontium Lt9611 is a DSI to HDMI bridge which supports two DSI ports and
I2S port as an input and HDMI port as output
Co-developed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Co-developed-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Tested-by: John Stultz <john.stultz@linaro.org>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Sam Ravnborg <sam@ravnborg.org> # fix lt9611_bridge_mode_valid
Link: https://patchwork.freedesktop.org/patch/msgid/20200723163442.1280414-4-vkoul@kernel.org
snd_soc_dai_digital_mute() is internally using both
mute_stream() (1) or digital_mute() (2), but the difference between
these 2 are only handling direction.
We can merge digital_mute() into mute_stream
int snd_soc_dai_digital_mute(xxx, int direction)
{
...
else if (dai->driver->ops->mute_stream)
(1) return dai->driver->ops->mute_stream(xxx, direction);
else if (direction == SNDRV_PCM_STREAM_PLAYBACK &&
dai->driver->ops->digital_mute)
(2) return dai->driver->ops->digital_mute(xxx);
...
}
For hdmi-codec, we need to update struct hdmi_codec_ops,
and all its users in the same time.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Reviewed-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Link: https://lore.kernel.org/r/87d055xxj2.wl-kuninori.morimoto.gx@renesas.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Using uninitialized_var() is dangerous as it papers over real bugs[1]
(or can in the future), and suppresses unrelated compiler warnings
(e.g. "unused variable"). If the compiler thinks it is uninitialized,
either simply initialize the variable or make compiler changes.
In preparation for removing[2] the[3] macro[4], remove all remaining
needless uses with the following script:
git grep '\buninitialized_var\b' | cut -d: -f1 | sort -u | \
xargs perl -pi -e \
's/\buninitialized_var\(([^\)]+)\)/\1/g;
s:\s*/\* (GCC be quiet|to make compiler happy) \*/$::g;'
drivers/video/fbdev/riva/riva_hw.c was manually tweaked to avoid
pathological white-space.
No outstanding warnings were found building allmodconfig with GCC 9.3.0
for x86_64, i386, arm64, arm, powerpc, powerpc64le, s390x, mips, sparc64,
alpha, and m68k.
[1] https://lore.kernel.org/lkml/20200603174714.192027-1-glider@google.com/
[2] https://lore.kernel.org/lkml/CA+55aFw+Vbj0i=1TGqCR5vQkCzWJ0QxK6CernOU6eedsudAixw@mail.gmail.com/
[3] https://lore.kernel.org/lkml/CA+55aFwgbgqhbp1fkxvRKEpzyR5J8n1vKT1VZdz9knmPuXhOeg@mail.gmail.com/
[4] https://lore.kernel.org/lkml/CA+55aFz2500WfbKXAx8s67wrm9=yVJu65TpLgN_ybYNv0VEOKA@mail.gmail.com/
Reviewed-by: Leon Romanovsky <leonro@mellanox.com> # drivers/infiniband and mlx4/mlx5
Acked-by: Jason Gunthorpe <jgg@mellanox.com> # IB
Acked-by: Kalle Valo <kvalo@codeaurora.org> # wireless drivers
Reviewed-by: Chao Yu <yuchao0@huawei.com> # erofs
Signed-off-by: Kees Cook <keescook@chromium.org>
clang static analysis flags this error
sil-sii8620.c:184:2: warning: Undefined or garbage value
returned to caller [core.uninitialized.UndefReturn]
return ret;
^~~~~~~~~~
sii8620_readb calls sii8620_read_buf.
sii8620_read_buf can return without setting its output
pararmeter 'ret'.
So initialize ret.
Fixes: ce6e153f41 ("drm/bridge: add Silicon Image SiI8620 driver")
Signed-off-by: Tom Rix <trix@redhat.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20200712152453.27510-1-trix@redhat.com
Rationale:
Reduces attack surface on kernel devs opening the links for MITM
as HTTPS traffic is much harder to manipulate.
Deterministic algorithm:
For each file:
If not .svg:
For each line:
If doesn't contain `\bxmlns\b`:
For each link, `\bhttp://[^# \t\r\n]*(?:\w|/)`:
If neither `\bgnu\.org/license`, nor `\bmozilla\.org/MPL\b`:
If both the HTTP and HTTPS versions
return 200 OK and serve the same content:
Replace HTTP with HTTPS.
Signed-off-by: Alexander A. Klimov <grandmaster@al2klimov.de>
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20200708121604.14292-1-grandmaster@al2klimov.de
It doesn't hurt to add the bridge in the global bridge list also for
platform specific dw-hdmi drivers which are based on the component
framework. This can be achieved by moving the drm_bridge_add() function
call from dw_hdmi_probe() to __dw_hdmi_probe(). A counterpart movement
for drm_bridge_remove() is also needed then. Moreover, since drm_bridge_add()
initializes &bridge->hpd_mutex, this may help those platform specific
dw-hdmi drivers(based on the component framework) avoid accessing the
uninitialized mutex in drm_bridge_hpd_notify() which is called in
dw_hdmi_irq(). Putting drm_bridge_add() in __dw_hdmi_probe() just before
it returns successfully should bring no logic change for platforms based
on the DRM bridge API, which is a good choice from safety point of view.
Also, __dw_hdmi_probe() is renamed to dw_hdmi_probe() since dw_hdmi_probe()
does nothing else but calling __dw_hdmi_probe(). Similar renaming applies
to the __dw_hdmi_remove()/dw_hdmi_remove() pair.
Fixes: ec971aaa67 ("drm: bridge: dw-hdmi: Make connector creation optional")
Cc: Andrzej Hajda <a.hajda@samsung.com>
Cc: Neil Armstrong <narmstrong@baylibre.com>
Cc: Laurent Pinchart <Laurent.pinchart@ideasonboard.com>
Cc: Jonas Karlman <jonas@kwiboo.se>
Cc: Jernej Skrabec <jernej.skrabec@siol.net>
Cc: David Airlie <airlied@linux.ie>
Cc: Daniel Vetter <daniel@ffwll.ch>
Cc: Boris Brezillon <boris.brezillon@collabora.com>
Cc: Jerome Brunet <jbrunet@baylibre.com>
Cc: Cheng-Yi Chiang <cychiang@chromium.org>
Cc: Dariusz Marcinkiewicz <darekm@google.com>
Cc: Archit Taneja <architt@codeaurora.org>
Cc: Jose Abreu <joabreu@synopsys.com>
Cc: Sam Ravnborg <sam@ravnborg.org>
Cc: dri-devel@lists.freedesktop.org
Cc: NXP Linux Team <linux-imx@nxp.com>
Signed-off-by: Liu Ying <victor.liu@nxp.com>
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Link: https://patchwork.freedesktop.org/patch/msgid/1594260156-8316-2-git-send-email-victor.liu@nxp.com
It's unnecessary to cleanup the i2c adapter and the ddc pointer in
the bailout path of __dw_hdmi_probe(), since the adapter is not
added and the ddc pointer is not set.
Fixes: a23d6265f0 ("drm: bridge: dw-hdmi: Extract PHY interrupt setup to a function")
Cc: Andrzej Hajda <a.hajda@samsung.com>
Cc: Neil Armstrong <narmstrong@baylibre.com>
Cc: Laurent Pinchart <Laurent.pinchart@ideasonboard.com>
Cc: Jonas Karlman <jonas@kwiboo.se>
Cc: Jernej Skrabec <jernej.skrabec@siol.net>
Cc: David Airlie <airlied@linux.ie>
Cc: Daniel Vetter <daniel@ffwll.ch>
Cc: Boris Brezillon <boris.brezillon@collabora.com>
Cc: Jerome Brunet <jbrunet@baylibre.com>
Cc: Cheng-Yi Chiang <cychiang@chromium.org>
Cc: Dariusz Marcinkiewicz <darekm@google.com>
Cc: Archit Taneja <architt@codeaurora.org>
Cc: Jose Abreu <joabreu@synopsys.com>
Cc: dri-devel@lists.freedesktop.org
Cc: NXP Linux Team <linux-imx@nxp.com>
Signed-off-by: Liu Ying <victor.liu@nxp.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Link: https://patchwork.freedesktop.org/patch/msgid/1594260156-8316-1-git-send-email-victor.liu@nxp.com
Some conflicts with ttm_bo->offset removal, but drm-misc-next needs updating to v5.8.
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
ti-sn65dsi86 bridge is enumerated as a runtime device. When
suspend is triggered, PM core adds a refcount on all the
devices and calls device suspend, since usage count is
already incremented, runtime suspend will not be called
and it kept the bridge regulators and gpios ON which resulted
in platform not entering into XO shutdown.
Add changes to force suspend on the runtime device during pm sleep.
Signed-off-by: Harigovindan P <harigovi@codeaurora.org>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200609120455.20458-1-harigovi@codeaurora.org
dw-mipi-dsi does not use any definition from drm_probe_helper.
Coverity output:
Event unnecessary_header:
Including .../include/drm/drm_probe_helper.h does not provide any
needed symbols.
Reviewed-by: Yannick Fertre <yannick.fertre@st.com>
Cc: Gustavo Pimentel <gustavo.pimentel@synopsys.com>
Cc: Joao Pinto <jpinto@synopsys.com>
Cc: Jose Abreu <jose.abreu@synopsys.com>
Signed-off-by: Angelo Ribeiro <angelo.ribeiro@synopsys.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/171ff1fb3918664a570dc8f2f34b446612505f76.1585832665.git.angelo.ribeiro@synopsys.com
UAPI Changes:
- Add DRM_MODE_TYPE_USERDEF for video modes specified in cmdline.
Cross-subsystem Changes:
- Assorted devicetree binding updates.
- Add might_sleep() to dma_fence_wait().
- Fix fbdev's get_user_pages_fast() handling, and use pin_user_pages.
- Small cleanup with IS_BUILTIN in video/fbdev drivers.
- Fix video/hdmi coding style for infoframe size.
Core Changes:
- Silence vblank output during init.
- Fix DP-MST corruption during send msg timeout.
- Clear leak in drm_gem_objecs_lookup().
- Make newlines work with force connector attribute.
- Fix module refcounting error in drm_encoder_slave, and use new i2c api.
- Header fix for drm_managed.c
- More struct_mutex removal for !legacy drivers:
- Remove gem_free_object()
- Removal of drm_gem_object_put_unlocked().
- Show current->comm alongside pid in debug printfs.
- Add drm_client_modeset_check() + drm_client_framebuffer_flush().
- Replace drm_fb_swab16 with drm_fb_swap that also supports 32-bits.
- Remove mode->vrefresh, and compactify drm_display_mode.
- Use drm_* macros for logging and warnings.
- Add WARN when drm_gem_get_pages is used on a private obj.
- Handle importing and imported dmabuf better in shmem helpers.
- Small fix for drm/mm hole size comparison, and remove invalid entry optimization.
- Add a drm/mm selftest.
- Set DSI connector type for DSI panels.
- Assorted small fixes and documentation updates.
- Fix DDI I2C device registration for MST ports, and flushing on destroy.
- Fix master_set return type, used by vmwgfx.
- Make the drm_set/drop_master ioctl symmetrical.
Driver Changes:
Allow iommu in the sun4i driver and use it for sun8i.
- Simplify backlight lookup for omap, amba-clcd and tilcdc.
- Hold reg_lock for rockchip.
- Add support for bridge gpio and lane reordering + polarity to ti-sn65dsi86, and fix clock choice.
- Small assorted fixes to tilcdc, vc4, i915, omap, fbdev/sm712fb, fbdev/pxafb, console/newport_con, msm, virtio, udl, malidp, hdlcd, bridge/ti-sn65dsi86, panfrost.
- Remove hw cursor support for mgag200, and use simple kms helper + shmem helpers.
- Add support for KOE Allow iommu in the sun4i driver and use it for sun8i.
- Simplify backlight lookup for omap, amba-clcd and tilcdc.
- Hold reg_lock for rockchip.
- Add support for bridge gpio and lane reordering + polarity to ti-sn65dsi86, and fix clock choice.
- Small assorted fixes to tilcdc, vc4 (multiple), i915.
- Remove hw cursor support for mgag200, and use simple kms helper + shmem helpers.
- Add support for KOE TX26D202VM0BWA panel.
- Use GEM CMA functions in arc, arm, atmel-hlcdc, fsi-dcu, hisilicon, imx, ingenic, komeda, malidp, mcde, meson, msxfb, rcar-du, shmobile, stm, sti, tilcdc, tve200, zte.
- Remove gem_print_info.
- Improve gem_create_object_helper so udl can use shmem helpers.
- Convert vc4 dt bindings to schemas, and add clock properties.
- Device initialization cleanups for mgag200.
- Add a workaround to fix DP-MST short pulses handling on broken hardware in i915.
- Allow build test compiling arm drivers.
- Use managed pci functions in mgag200 and ast.
- Use dev_groups in malidp.
- Add per pixel alpha support for PX30 VOP in rockchip.
- Silence deferred probe logs in panfrost.
-----BEGIN PGP SIGNATURE-----
iQIzBAABCgAdFiEEuXvWqAysSYEJGuVH/lWMcqZwE8MFAl7s11IACgkQ/lWMcqZw
E8OYnQ/+K4ZGpU11t4IzXCyJYis2ZPYs/FlJ2BWXH89YhOckN1e1tq7uDBzUE8qK
Hlz0gvH5C0WXR/PWqNglPXW7INwc0LtC8PSmvS4vvrZQBaJ2bvf19y7dROqJbR0E
xTUje95eq+10H9TysCRTf1osIUuZIoR0gRna22pb+nplKVBkqsQPyPT21AWq4fN0
H/LQfKNfAAHtKwvfsMsuG2U+ZTyTYo7Xi6UP413WAqDmzhewnCm5plifM29m5LhB
9BmKk0/1pL3KzZuCQvcZw4kYUjXYsgoOqD4hkMAOLsjyf6Ad5zbPB5YTxNK0C+NU
N04aHWvkRVl62A6rehgXdS5GJ3M4ORPDpIV9zQCVxMZV/886JLTGA1Wb+b3+umdk
t5M40kzgYQTDqdSwFoCDCd1tFpEjnLbE7E+eM89AyzTPOxZowrVS0No1dJA3+ST/
g7JOdDu2Zg7VAar6zByow0pMppikZro9H1mpSnk+WHbYNF3dFmW3QHKRuxoRt+Ee
l5G52LylwH3ZMPebGH9XB4cWtAUAHOsioe3CS/PKzGeUWNlUK29AqDCCBQmUdbcT
HNm5/Yygdg3rRjkDBuUI0I/pifxMYvm+28eNfNGjwq5To9ABXPNONQCEBH6rke+S
d1Z2nMmiVDf2MqhpkJppTKtHdMz13IGyZykXB7CdGnAu6k5s59c=
=ZmKI
-----END PGP SIGNATURE-----
Merge tag 'drm-misc-next-2020-06-19' of git://anongit.freedesktop.org/drm/drm-misc into drm-next
drm-misc-next for v5.9:
UAPI Changes:
- Add DRM_MODE_TYPE_USERDEF for video modes specified in cmdline.
Cross-subsystem Changes:
- Assorted devicetree binding updates.
- Add might_sleep() to dma_fence_wait().
- Fix fbdev's get_user_pages_fast() handling, and use pin_user_pages.
- Small cleanup with IS_BUILTIN in video/fbdev drivers.
- Fix video/hdmi coding style for infoframe size.
Core Changes:
- Silence vblank output during init.
- Fix DP-MST corruption during send msg timeout.
- Clear leak in drm_gem_objecs_lookup().
- Make newlines work with force connector attribute.
- Fix module refcounting error in drm_encoder_slave, and use new i2c api.
- Header fix for drm_managed.c
- More struct_mutex removal for !legacy drivers:
- Remove gem_free_object()
- Removal of drm_gem_object_put_unlocked().
- Show current->comm alongside pid in debug printfs.
- Add drm_client_modeset_check() + drm_client_framebuffer_flush().
- Replace drm_fb_swab16 with drm_fb_swap that also supports 32-bits.
- Remove mode->vrefresh, and compactify drm_display_mode.
- Use drm_* macros for logging and warnings.
- Add WARN when drm_gem_get_pages is used on a private obj.
- Handle importing and imported dmabuf better in shmem helpers.
- Small fix for drm/mm hole size comparison, and remove invalid entry optimization.
- Add a drm/mm selftest.
- Set DSI connector type for DSI panels.
- Assorted small fixes and documentation updates.
- Fix DDI I2C device registration for MST ports, and flushing on destroy.
- Fix master_set return type, used by vmwgfx.
- Make the drm_set/drop_master ioctl symmetrical.
Driver Changes:
Allow iommu in the sun4i driver and use it for sun8i.
- Simplify backlight lookup for omap, amba-clcd and tilcdc.
- Hold reg_lock for rockchip.
- Add support for bridge gpio and lane reordering + polarity to ti-sn65dsi86, and fix clock choice.
- Small assorted fixes to tilcdc, vc4, i915, omap, fbdev/sm712fb, fbdev/pxafb, console/newport_con, msm, virtio, udl, malidp, hdlcd, bridge/ti-sn65dsi86, panfrost.
- Remove hw cursor support for mgag200, and use simple kms helper + shmem helpers.
- Add support for KOE Allow iommu in the sun4i driver and use it for sun8i.
- Simplify backlight lookup for omap, amba-clcd and tilcdc.
- Hold reg_lock for rockchip.
- Add support for bridge gpio and lane reordering + polarity to ti-sn65dsi86, and fix clock choice.
- Small assorted fixes to tilcdc, vc4 (multiple), i915.
- Remove hw cursor support for mgag200, and use simple kms helper + shmem helpers.
- Add support for KOE TX26D202VM0BWA panel.
- Use GEM CMA functions in arc, arm, atmel-hlcdc, fsi-dcu, hisilicon, imx, ingenic, komeda, malidp, mcde, meson, msxfb, rcar-du, shmobile, stm, sti, tilcdc, tve200, zte.
- Remove gem_print_info.
- Improve gem_create_object_helper so udl can use shmem helpers.
- Convert vc4 dt bindings to schemas, and add clock properties.
- Device initialization cleanups for mgag200.
- Add a workaround to fix DP-MST short pulses handling on broken hardware in i915.
- Allow build test compiling arm drivers.
- Use managed pci functions in mgag200 and ast.
- Use dev_groups in malidp.
- Add per pixel alpha support for PX30 VOP in rockchip.
- Silence deferred probe logs in panfrost.
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/001cd9a6-405d-4e29-43d8-354f53ae4e8b@linux.intel.com
Implement the drm_bridge_funcs .detect() and .get_edid() operations, and
call drm_bridge_hpd_notify() notify to report HPD. This provides the
necessary API to support disabling connector creation, do so by
accepting DRM_BRIDGE_ATTACH_NO_CONNECTOR in dw_hdmi_bridge_attach().
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20200526011505.31884-23-laurent.pinchart+renesas@ideasonboard.com
To prepare for making connector creation optional in the driver, pass
the drm_connector explicitly to the internal functions that require it.
The functions that still access the connector from the dw_hdmi structure
are dw_hdmi_connector_create() and __dw_hdmi_probe(). The former access
is expected, as that's where the internal connector is created. The
latter will be addressed separately.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20200526011505.31884-22-laurent.pinchart+renesas@ideasonboard.com
Store the connector that the bridge is currently wired to in the dw_hdmi
structure. This is currently identical to the connector field, but will
differ once the driver supports disabling connector creation.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20200526011505.31884-21-laurent.pinchart+renesas@ideasonboard.com
To prepare for making connector creation optional in the driver, pass
the drm_display_info explicitly to dw_hdmi_support_scdc(). The pointer
is passed to the callers where required, particularly to the
dw_hdmi_phy_ops .init() function.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20200526011505.31884-19-laurent.pinchart+renesas@ideasonboard.com
Several internal functions take a drm_display_mode argument to configure
the HDMI encoder or the HDMI PHY. They must not modify the mode, make
the pointer const to enforce that.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20200526011505.31884-18-laurent.pinchart+renesas@ideasonboard.com
Replace the drm_connector pointer passed to the .mode_valid() function
with a const drm_display_info pointer, as that's all the function should
need. Use the display info passed to the bridge .mode_valid() operation
instead of retrieving it from the connector, to prepare for make
connector creation optional.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20200526011505.31884-16-laurent.pinchart+renesas@ideasonboard.com
The .configure_phy() operation takes a dw_hdmi_plat_data pointer as a
context argument. This differs from .mode_valid() that takes a custom
private context pointer, causing possible confusion. Make the
dw_hdmi_plat_data operations more consistent by passing the private
context pointer to .configure_phy() as well.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20200526011505.31884-13-laurent.pinchart+renesas@ideasonboard.com
Platform glue drivers for dw_hdmi may need to access device-specific
data from their .mode_valid() implementation. They currently have no
clean way to do so, and one driver hacks around it by accessing the
dev_private data of the drm_device retrieved from the connector.
Add a priv_data void pointer to the dw_hdmi_plat_data structure, and
pass it to the .mode_valid() function.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20200526011505.31884-12-laurent.pinchart+renesas@ideasonboard.com
When validating a mode, bridges may need to do so in the context of a
display, as specified by drm_display_info. An example is the meson
dw-hdmi bridge that needs to consider the YUV 4:2:0 output format to
perform clock calculations.
Bridges that need the display info currently retrieve it from the
drm_connector created by the bridge. This gets in the way of moving
connector creation out of bridge drivers. To make this possible, pass
the drm_display_info to drm_bridge_funcs .mode_valid().
Changes to the bridge drivers have been performed with the following
coccinelle semantic patch and have been compile-tested.
@ rule1 @
identifier funcs;
identifier fn;
@@
struct drm_bridge_funcs funcs = {
...,
.mode_valid = fn
};
@ depends on rule1 @
identifier rule1.fn;
identifier bridge;
identifier mode;
@@
enum drm_mode_status fn(
struct drm_bridge *bridge,
+ const struct drm_display_info *info,
const struct drm_display_mode *mode
)
{
...
}
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Boris Brezillon <boris.brezillon@collabora.com>
Reviewed-by: Guido Günther <agx@sigxcpu.org> # for the nwl-dsi part:
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20200526011505.31884-11-laurent.pinchart+renesas@ideasonboard.com
Instead of poking into the DT node of the next bridge for its DDC bus
and implementing the .get_modes() and .detect() connector operations
manually, retrieve the next bridge in the chain and delegate these
operations to it.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20200526011505.31884-7-laurent.pinchart+renesas@ideasonboard.com
The drm_bridge_get_edid() function is documented to return an error
pointer on error. The underlying .get_edid() operation, however, returns
NULL on error, and so do the drm_get_edid() and drm_do_get_edid()
functions upon which .get_edid() is usually implemented. Make
drm_bridge_get_edid() return NULL on error to be consistent.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20200526011505.31884-6-laurent.pinchart+renesas@ideasonboard.com
Now that the driver supports all the connector-related bridge
operations, make the connector creation optional. This enables usage of
the adv7511 with the DRM bridge connector helper.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20200526011505.31884-5-laurent.pinchart+renesas@ideasonboard.com
Implement the bridge connector-related .get_edid(), .detect() and
.hpd_notify() operations, and report the related bridge capabilities.
Output status detection is implemented using the same backend as for the
DRM connector, but requires making mode retrieval at detection time
optional as no pointer to the connector is available to the bridge
.detect() operation. The reason for the need to retrieve modes at
detection time is unclear to me, and this may benefit from further
refactoring of hot plug handling code.
Hot plug detection is notified through the bridge HPD notification
framework when the bridge is used without creating a connector, and
falls back to the existing implementation otherwise. CEC handling of
disconnection is handled in the new .hpd_notify() operation in the new
code path.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20200526011505.31884-4-laurent.pinchart+renesas@ideasonboard.com
The tfp410 has a data de-skew feature that allows the user to compensate
the skew between IDCK and the pixel data and control signals.
In the driver, the setup and hold times are calculated from the de-skew
value. This retrieves the deskew value from the DT using the proper
datatype and range check as described by the binding (u32 from 0 to 7).
This fix results from a change in the ti,tfp410 DT binding.
Signed-off-by: Ricardo Cañuelo <ricardo.canuelo@collabora.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20200617094633.19663-4-ricardo.canuelo@collabora.com
The ti_sn_bridge_gpio_set() got the return value of
regmap_update_bits() but didn't check it. The function can't return
an error value, but we should at least print a warning if it didn't
work.
This fixes a compiler warning about setting "ret" but not using it.
Fixes: 27ed2b3f22 ("drm/bridge: ti-sn65dsi86: Export bridge GPIOs to Linux")
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200612123003.v2.4.Ia4376fd88cdc6e8f8b43c65548458305f82f1d61@changeid
When building we were getting an error:
warning: cannot understand function prototype:
'const unsigned int ti_sn_bridge_dp_rate_lut[] = '
Arrays aren't supposed to be marked with "/**" kerneldoc comments. Fix.
Fixes: a095f15c00 ("drm/bridge: add support for sn65dsi86 bridge driver")
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200612123003.v2.2.If3807e4ebf7f0440f64c3069edcfac9a70171940@changeid
The kernel test robot noted that if "OF" is defined (which is needed
to select DRM_TI_SN65DSI86 at all) but not OF_GPIO that we'd get
compile failures because some of the members that we access in "struct
gpio_chip" are only defined "#if defined(CONFIG_OF_GPIO)".
All the GPIO bits in the driver are all nicely separated out. We'll
guard them with the same "#if defined" that the header has and add a
little stub function if OF_GPIO is not defined.
Fixes: 27ed2b3f22 ("drm/bridge: ti-sn65dsi86: Export bridge GPIOs to Linux")
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200612123003.v2.1.Ibe95d8f3daef01e5c57d4c8c398f04d6a839492c@changeid
Since commit 84af7a6194 ("checkpatch: kconfig: prefer 'help' over
'---help---'"), the number of '---help---' has been gradually
decreasing, but there are still more than 2400 instances.
This commit finishes the conversion. While I touched the lines,
I also fixed the indentation.
There are a variety of indentation styles found.
a) 4 spaces + '---help---'
b) 7 spaces + '---help---'
c) 8 spaces + '---help---'
d) 1 space + 1 tab + '---help---'
e) 1 tab + '---help---' (correct indentation)
f) 1 tab + 1 space + '---help---'
g) 1 tab + 2 spaces + '---help---'
In order to convert all of them to 1 tab + 'help', I ran the
following commend:
$ find . -name 'Kconfig*' | xargs sed -i 's/^[[:space:]]*---help---/\thelp/'
Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>
- remove a now unnecessary usage of the KERNEL_DS for
sys_oabi_epoll_ctl()
- update my email address in a number of drivers
- decompressor EFI updates from Ard Biesheuvel
- module unwind section handling updates
- sparsemem Kconfig cleanups
- make act_mm macro respect THREAD_SIZE
-----BEGIN PGP SIGNATURE-----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=vMHE
-----END PGP SIGNATURE-----
Merge tag 'for-linus' of git://git.armlinux.org.uk/~rmk/linux-arm
Pull ARM updates from Russell King:
- remove a now unnecessary usage of the KERNEL_DS for
sys_oabi_epoll_ctl()
- update my email address in a number of drivers
- decompressor EFI updates from Ard Biesheuvel
- module unwind section handling updates
- sparsemem Kconfig cleanups
- make act_mm macro respect THREAD_SIZE
* tag 'for-linus' of git://git.armlinux.org.uk/~rmk/linux-arm:
ARM: 8980/1: Allow either FLATMEM or SPARSEMEM on the multiplatform build
ARM: 8979/1: Remove redundant ARCH_SPARSEMEM_DEFAULT setting
ARM: 8978/1: mm: make act_mm() respect THREAD_SIZE
ARM: decompressor: run decompressor in place if loaded via UEFI
ARM: decompressor: move GOT into .data for EFI enabled builds
ARM: decompressor: defer loading of the contents of the LC0 structure
ARM: decompressor: split off _edata and stack base into separate object
ARM: decompressor: move headroom variable out of LC0
ARM: 8976/1: module: allow arch overrides for .init section names
ARM: 8975/1: module: fix handling of unwind init sections
ARM: 8974/1: use SPARSMEM_STATIC when SPARSEMEM is enabled
ARM: 8971/1: replace the sole use of a symbol with its definition
ARM: 8969/1: decompressor: simplify libfdt builds
Update rmk's email address in various drivers
ARM: compat: remove KERNEL_DS usage in sys_oabi_epoll_ctl()
The ti-sn65dsi86 MIPI DSI to eDP bridge chip supports arbitrary
remapping of eDP lanes and also polarity inversion. Both of these
features have been described in the device tree bindings for the
device since the beginning but were never implemented in the driver.
Implement both of them.
Part of this change also allows you to (via the same device tree
bindings) specify to use fewer than the max number of DP lanes that
the panel reports. This could be useful if your display supports more
lanes but only a few are hooked up on your board.
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Reviewed-by: Rob Clark <robdclark@gmail.com>
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20200518114656.REPOST.v2.1.Ibc8eeddcee94984a608d6900b46f9ffde4045da4@changeid
If the rate in our table is _equal_ to the rate we want then it's OK
to pick it. It doesn't need to be greater than the one we want.
Fixes: a095f15c00 ("drm/bridge: add support for sn65dsi86 bridge driver")
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Reviewed-by: Rob Clark <robdclark@gmail.com>
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20200504213225.1.I21646c7c37ff63f52ae6cdccc9bc829fbc3d9424@changeid
The AUX channel transfer error bits in the status register are latched
and need to be cleared. Clear them before doing our transfer so we
don't see old bits and get confused.
Without this patch having a single failure would mean that all future
transfers would look like they failed.
Fixes: b814ec6d45 ("drm/bridge: ti-sn65dsi86: Implement AUX channel")
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Rob Clark <robdclark@gmail.com>
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20200508163314.1.Idfa69d5d3fc9623083c0ff78572fea87dccb199c@changeid
The ti-sn65dsi86 MIPI DSI to eDP bridge chip has 4 pins on it that can
be used as GPIOs in a system. Each pin can be configured as input,
output, or a special function for the bridge chip. These are:
- GPIO1: SUSPEND Input
- GPIO2: DSIA VSYNC
- GPIO3: DSIA HSYNC or VSYNC
- GPIO4: PWM
Let's expose these pins as GPIOs. A few notes:
- Access to ti-sn65dsi86 is via i2c so we set "can_sleep".
- These pins can't be configured for IRQ.
- There are no programmable pulls or other fancy features.
- Keeping the bridge chip powered might be expensive. The driver is
setup such that if all used GPIOs are only inputs we'll power the
bridge chip on just long enough to read the GPIO and then power it
off again. Setting a GPIO as output will keep the bridge powered.
- If someone releases a GPIO we'll implicitly switch it to an input so
we no longer need to keep the bridge powered for it.
Because of all of the above limitations we just need to implement a
bare-bones GPIO driver. The device tree bindings already account for
this device being a GPIO controller so we only need the driver changes
for it.
NOTE: Despite the fact that these pins are nominally muxable I don't
believe it makes sense to expose them through the pinctrl interface as
well as the GPIO interface. The special functions are things that the
bridge chip driver itself would care about and it can just configure
the pins as needed.
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
[added pdata->gchip.base = -1;]
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20200507143354.v5.1.Ia50267a5549392af8b37e67092ca653a59c95886@changeid
This is a driver for video encoder with VGA and DVI/HDMI outputs.
There is no documentation for the chip -- the operation was guessed from
what was sniffed on a Dell Wyse 3020 ThinOS terminal, the register names
come from the ch7035 driver in Mediatek's GPL code dump.
Only bare minimum is implemented -- no fancy stuff, such as scaling. That
would only worsen our misery. We don't load the firmware and we don't need
to even bother enabling the MCU. There are probably no distributable
firmware images anyway.
Tested with a handful of monitors ranging from 1024x768@75 to 1400x1050@60,
with VGA as well as DVI.
Signed-off-by: Lubomir Rintel <lkundrak@v3.sk>
Acked-by: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200424213539.93157-4-lkundrak@v3.sk
Some older versions of gcc badly optimize code that passes
an inline function argument into another function by reference,
causing huge stack usage:
drivers/gpu/drm/bridge/tc358768.c: In function 'tc358768_bridge_pre_enable':
drivers/gpu/drm/bridge/tc358768.c:840:1: error: the frame size of 2256 bytes is larger than 2048 bytes [-Werror=frame-larger-than=]
Use a temporary variable as a workaround and add a comment pointing
to the gcc bug.
Fixes: ff1ca6397b ("drm/bridge: Add tc358768 driver")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20200428215408.4111675-1-arnd@arndb.de
Since commit 89958b7cd9 ("drm/bridge: panel: Infer connector type from
panel by default"), drm_panel_bridge_add() and their variants can return
NULL and an error pointer. This is fine but none of the actual users of
the API are checking for the NULL value. Instead of change all the
users, seems reasonable to return an error pointer instead. So change
the returned value for those functions when the connector type is unknown.
Suggested-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20200416210654.2468805-1-enric.balletbo@collabora.com
The panel connector type should be set by the panel not the bridge, so
remove the connector_type assignment.
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20200416164404.2418426-2-enric.balletbo@collabora.com
Globally update my email address in six files scattered through the
tree.
Acked-by: Sam Ravnborg <sam@ravnborg.org>
Acked-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Some drivers (e.g. sun4i-drm) need this info to decide whether they
need to enable dithering. Currently driver reports what panel supports
and if panel supports 8 we don't get dithering enabled.
Hardcode BPC to 6 for now since that's the only BPC
that driver supports.
Fixes: 6aa1926980 ("drm/bridge: Add Analogix anx6345 support")
Signed-off-by: Vasily Khoruzhick <anarsoul@gmail.com>
Acked-by: Jernej Skrabec <jernej.skrabec@siol.net>
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Link: https://patchwork.freedesktop.org/patch/msgid/20200329222253.2941405-1-anarsoul@gmail.com
ADV7511 support sample rates up to 192kHz. CTS and N parameters should
be computed accordingly so this commit extend the list up to maximum
supported sample rate.
Signed-off-by: Bogdan Togorean <bogdan.togorean@analog.com>
Reviewed-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200413113513.86091-2-bogdan.togorean@analog.com
This adds initial support for the NWL MIPI DSI Host controller found on
i.MX8 SoCs.
It adds support for the i.MX8MQ but the same IP can be found on
e.g. the i.MX8QXP.
It has been tested on the Librem 5 devkit using mxsfb.
Signed-off-by: Guido Günther <agx@sigxcpu.org>
Co-developed-by: Robert Chiras <robert.chiras@nxp.com>
Signed-off-by: Robert Chiras <robert.chiras@nxp.com>
Tested-by: Robert Chiras <robert.chiras@nxp.com>
Tested-by: Martin Kepplinger <martin.kepplinger@puri.sm>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Link: https://patchwork.freedesktop.org/patch/msgid/1cf5750f734e33d005564cd89c576eaf3c1c192b.1586427783.git.agx@sigxcpu.org
Analogix_dp driver acquires all its resources in the ->bind() callback,
what is a bit against the component driver based approach, where the
driver initialization is split into a probe(), where all resources are
gathered, and a bind(), where all objects are created and a compound
driver is initialized.
Extract all the resource related operations to analogix_dp_probe() and
analogix_dp_remove(), then call them before/after registration of the
device components from the main Exynos DP and Rockchip DP drivers. Also
move the plat_data initialization to the probe() to make it available for
the analogix_dp_probe() function.
This fixes the multiple calls to the bind() of the DRM compound driver
when the DP PHY driver is not yet loaded/probed:
[drm] Exynos DRM: using 14400000.fimd device for DMA mapping operations
exynos-drm exynos-drm: bound 14400000.fimd (ops fimd_component_ops [exynosdrm])
exynos-drm exynos-drm: bound 14450000.mixer (ops mixer_component_ops [exynosdrm])
exynos-dp 145b0000.dp-controller: no DP phy configured
exynos-drm exynos-drm: failed to bind 145b0000.dp-controller (ops exynos_dp_ops [exynosdrm]): -517
exynos-drm exynos-drm: master bind failed: -517
...
[drm] Exynos DRM: using 14400000.fimd device for DMA mapping operations
exynos-drm exynos-drm: bound 14400000.fimd (ops hdmi_enable [exynosdrm])
exynos-drm exynos-drm: bound 14450000.mixer (ops hdmi_enable [exynosdrm])
exynos-drm exynos-drm: bound 145b0000.dp-controller (ops hdmi_enable [exynosdrm])
exynos-drm exynos-drm: bound 14530000.hdmi (ops hdmi_enable [exynosdrm])
[drm] Supports vblank timestamp caching Rev 2 (21.10.2013).
Console: switching to colour frame buffer device 170x48
exynos-drm exynos-drm: fb0: exynosdrmfb frame buffer device
[drm] Initialized exynos 1.1.0 20180330 for exynos-drm on minor 1
...
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Acked-by: Andy Yan <andy.yan@rock-chips.com>
Reviewed-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200310103427.26048-1-m.szyprowski@samsung.com
(cherry picked from commit 83a196773b)
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Add missing documentation to fix following warning:
panel.c:303: warning: Function parameter or member 'bridge' not described in 'drm_panel_bridge_connector'
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: Boris Brezillon <boris.brezillon@collabora.com>
Cc: Mihail Atanassov <Mihail.Atanassov@arm.com>
Cc: Andrzej Hajda <a.hajda@samsung.com>
Cc: Neil Armstrong <narmstrong@baylibre.com>
Cc: Jonas Karlman <jonas@kwiboo.se>
Cc: Jernej Skrabec <jernej.skrabec@siol.net>
Link: https://patchwork.freedesktop.org/patch/msgid/20200328132025.19910-7-sam@ravnborg.org
-----BEGIN PGP SIGNATURE-----
iQFSBAABCAA8FiEEq68RxlopcLEwq+PEeb4+QwBBGIYFAl6BIG4eHHRvcnZhbGRz
QGxpbnV4LWZvdW5kYXRpb24ub3JnAAoJEHm+PkMAQRiGlHUH/RCFve2sfHRPjRW+
xR5SaLVAw6XKvtKBq7yvKmHEwqNJnL79IHyqqtSrtfFr2FfaH/KvYiCbbAezvSrM
np0udGu7STKGd21CWuyEZJudyhXkOwMRNiFiCXWp7rs35oh8T0TpJxMzo2Nc1nLk
JFQPqAP6OSvq4IkWEywKQI+Au3Z1IBf83xVjZ1s+MKPQHYD49x2hc4cQntL5/cnm
a3DoR2iBkYiGZCZ9dDqAqJTnMQIiCbACdZXgGjNRUpdyA/dtAjsMl11NPYHm8TA2
3AHBupAK50WBZGad6xv2qKQyScsmoJG2mv92QjlOFz0Tpiu6rLnDlLYREDVB6YH6
qbLDsc8=
=XEIU
-----END PGP SIGNATURE-----
Merge v5.6 into drm-next
msm needed rc6, so I just went and merged release
(msm has been in drm-next outside of this tree)
Signed-off-by: Dave Airlie <airlied@redhat.com>
Don't confuse user with meaningless warning about failure in getting
regulators in case of deferred probe.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200226101307.16708-1-m.szyprowski@samsung.com
is_color_space_conversion() is a misnomer. It checks not only if color
space conversion is needed, but also if format conversion is needed.
This is actually desired behaviour because result of this function
determines if CSC block should be enabled or not (CSC block can also do
format conversion).
In order to clear misunderstandings, let's rework
is_color_space_conversion() to do exactly what is supposed to do and add
another function which will determine if CSC block must be enabled or
not.
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Link: https://patchwork.freedesktop.org/patch/msgid/20200304232512.51616-5-jernej.skrabec@siol.net
CEA 861 standard requestis that RGB quantization range is "limited" for
CEA modes. Support that by adding CSC matrix which downscales values.
This allows proper color reproduction on TV and PC monitor at the same
time. In future, override property can be added, like "Broadcast RGB"
in i915 driver.
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Link: https://patchwork.freedesktop.org/patch/msgid/20200304232512.51616-4-jernej.skrabec@siol.net
Setting scan mode to "none" confuses some TVs like LG B8, which randomly
change overscan percentage over time. Digital outputs like HDMI and DVI,
handled by this controller, don't really need overscan, so we can always
set scan mode to underscan. Actually, this is exactly what
drm_hdmi_avi_infoframe_from_display_mode() already does, so we can just
remove offending line.
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
[updated commit message]
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Link: https://patchwork.freedesktop.org/patch/msgid/20200304232512.51616-3-jernej.skrabec@siol.net
-----BEGIN PGP SIGNATURE-----
iQFSBAABCAA8FiEEq68RxlopcLEwq+PEeb4+QwBBGIYFAl5lkYceHHRvcnZhbGRz
QGxpbnV4LWZvdW5kYXRpb24ub3JnAAoJEHm+PkMAQRiGpHQH/RJrzcaZHo4lw88m
Jf7vBZ9DYUlRgqE0pxTHWmodNObKRqpwOUGflUcWbb/7GD2LQUfeqhSECVQyTID9
N9y7FcPvx321Qhc3EkZ24DBYk0+DQ0K2FVUrSa/PxO0n7czxxXWaLRDmlSULEd3R
D4pVs3zEWOBXJHUAvUQ5R+lKfkeWKNeeepeh+rezuhpdWFBRNz4Jjr5QUJ8od5xI
sIwobYmESJqTRVBHqW8g2T2/yIsFJ78GCXs8DZLe1wxh40UbxdYDTA0NDDTHKzK6
lxzBgcmKzuge+1OVmzxLouNWMnPcjFlVgXWVerpSy3/SIFFkzzUWeMbqm6hKuhOn
wAlcIgI=
=VQUc
-----END PGP SIGNATURE-----
Merge v5.6-rc5 into drm-next
Requested my mripard for some misc patches that need this as a base.
Signed-off-by: Dave Airlie <airlied@redhat.com>
Now the DW-HDMI Controller supports the HDMI2.0 modes, enable support
for these modes in the connector if the platform supports them.
We limit these modes to DW-HDMI IP version >= 0x200a which
are designed to support HDMI2.0 display modes.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Andrzej Hajda <a.hajda@samsung.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Jernej Škrabec <jernej.skrabec@siol.net>
Link: https://patchwork.freedesktop.org/patch/msgid/20200304104052.17196-6-narmstrong@baylibre.com
Add the atomic_get_output_bus_fmts, atomic_get_input_bus_fmts to negociate
the possible output and input formats for the current mode and monitor,
and use the negotiated formats in a basic atomic_check callback.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Boris Brezillon <boris.brezillon@collabora.com>
Reviewed-by: Jernej Škrabec <jernej.skrabec@siol.net>
Link: https://patchwork.freedesktop.org/patch/msgid/20200304104052.17196-5-narmstrong@baylibre.com
Add the max_bpc property to the dw-hdmi connector to prepare support
for 10, 12 & 16bit output support.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Jernej Škrabec <jernej.skrabec@siol.net>
Link: https://patchwork.freedesktop.org/patch/msgid/20200304104052.17196-3-narmstrong@baylibre.com
drm_fb_helper_{add,remove}_one_connector() and
drm_fb_helper_single_add_all_connectors() are dummy functions now
and serve no purpose. Hence remove their calls.
This is the preparatory step for removing the
drm_fb_helper_{add,remove}_one_connector() functions from
drm_fb_helper.h
This removal is done using below sementic patch and unused variable
compilation warnings are fixed manually.
@@
@@
- drm_fb_helper_single_add_all_connectors(...);
@@
expression e1;
statement S;
@@
- e1 = drm_fb_helper_single_add_all_connectors(...);
- S
@@
@@
- drm_fb_helper_add_one_connector(...);
@@
@@
- drm_fb_helper_remove_one_connector(...);
Changes since v1:
* Squashed warning fixes into the patch that introduced the
warnings (into 5/7) (Laurent, Emil, Lyude)
Signed-off-by: Pankaj Bharadiya <pankaj.laxminarayan.bharadiya@intel.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Emil Velikov <emil.velikov@collabora.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Lyude Paul <lyude@redhat.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/20200305120434.111091-6-pankaj.laxminarayan.bharadiya@intel.com
Current code tries to store the link rate (in bps, which is a big
number) in a u8, which surely overflow. Then it's converted back to
bandwidth code (which is thus 0) and written to the chip.
The code sometimes works because the chip will automatically fallback to
the lowest possible DP link rate (1.62Gbps) when get the invalid value.
However, on the eDP panel of Olimex TERES-I, which wants 2.7Gbps link,
it failed.
As we had already read the link bandwidth as bandwidth code in earlier
code (to check whether it is supported), use it when setting bandwidth,
instead of converting it to link rate and then converting back.
Fixes: e1cff82c10 ("drm/bridge: fix anx6345 compilation for v5.5")
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Reviewed-by: Torsten Duwe <duwe@suse.de>
Cc: Maxime Ripard <maxime@cerno.tech>
Cc: Torsten Duwe <duwe@lst.de>
Cc: Sam Ravnborg <sam@ravnborg.org>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Thomas Zimmermann <tzimmermann@suse.de>
Cc: Icenowy Zheng <icenowy@aosc.io>
Cc: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Link: https://patchwork.freedesktop.org/patch/msgid/20200221165127.813325-1-icenowy@aosc.io
The tfp410 driver can operate as part of a pipeline where the
drm_connector is created by the display controller. Enable this mode of
operation by skipping creation of a drm_connector internally.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Boris Brezillon <boris.brezillon@collabora.com>
Acked-by: Sam Ravnborg <sam@ravnborg.org>
Tested-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200226112514.12455-20-laurent.pinchart@ideasonboard.com
Now that a driver is available for display connectors, replace the
manual connector handling code with usage of the DRM bridge API. The
tfp410 driver doesn't deal with the display connector directly anymore,
but still delegates drm_connector operations to the next bridge. This
brings us one step closer to having the tfp410 driver handling the
TFP410 only.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Sam Ravnborg <sam@ravnborg.org>
Tested-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200226112514.12455-19-laurent.pinchart@ideasonboard.com
Implement the newly added bridge connector operations, allowing the
usage of drm_bridge_panel with drm_bridge_connector.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Boris Brezillon <boris.brezillon@collabora.com>
Reviewed-by: Sam Ravnborg <sam@ravnborg.org>
Tested-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200226112514.12455-18-laurent.pinchart@ideasonboard.com
The TI TPD12S015 is an HDMI level shifter and ESD protector controlled
through GPIOs. Add a DRM bridge driver for the device.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Acked-by: Sam Ravnborg <sam@ravnborg.org>
Tested-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200226112514.12455-17-laurent.pinchart@ideasonboard.com
Display connectors are modelled in DT as a device node, but have so far
been handled manually in several bridge drivers. This resulted in
duplicate code in several bridge drivers, with slightly different (and
thus confusing) logics.
In order to fix this, implement a bridge driver for display connectors.
The driver centralises logic for the DVI, HDMI, VGAn composite and
S-video connectors and exposes corresponding bridge operations.
This driver in itself doesn't solve the issue completely, changes in
bridge and display controller drivers are needed to make use of the new
connector driver.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Maxime Ripard <mripard@kernel.org>
Reviewed-by: Boris Brezillon <boris.brezillon@collabora.com>
Acked-by: Sam Ravnborg <sam@ravnborg.org>
Tested-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200226112514.12455-16-laurent.pinchart@ideasonboard.com
The TI OPA362 is an analog video amplifier controlled through a GPIO. Add
support for it to the simple-bridge driver.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Andrzej Hajda <a.hajda@samsung.com>
Reviewed-by: Boris Brezillon <boris.brezillon@collabora.com>
Reviewed-by: Maxime Ripard <mripard@kernel.org>
Reviewed-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Acked-by: Sam Ravnborg <sam@ravnborg.org>
Tested-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200226112514.12455-15-laurent.pinchart@ideasonboard.com
If an enable GPIO is declared in the firmware, assert it when enabling
the bridge and deassert it when disabling it.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Andrzej Hajda <a.hajda@samsung.com>
Reviewed-by: Stefan Agner <stefan@agner.ch>
Reviewed-by: Boris Brezillon <boris.brezillon@collabora.com>
Reviewed-by: Maxime Ripard <mripard@kernel.org>
Acked-by: Sam Ravnborg <sam@ravnborg.org>
Tested-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200226112514.12455-14-laurent.pinchart@ideasonboard.com
Create a new simple_bridge_info structure that stores information about
the bridge model, and store the bridge timings in there, along with the
connector type. Use that new structure for of_device_id data. This
enables support for non-VGA bridges.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Andrzej Hajda <a.hajda@samsung.com>
Reviewed-by: Stefan Agner <stefan@agner.ch>
Reviewed-by: Boris Brezillon <boris.brezillon@collabora.com>
Reviewed-by: Maxime Ripard <mripard@kernel.org>
Acked-by: Sam Ravnborg <sam@ravnborg.org>
Tested-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200226112514.12455-13-laurent.pinchart@ideasonboard.com
The dumb-vga-dac driver can support simple DRM bridges without being
limited to VGA DACs. Rename it to simple-bridge.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Andrzej Hajda <a.hajda@samsung.com>
Reviewed-by: Boris Brezillon <boris.brezillon@collabora.com>
Acked-by: Maxime Ripard <mripard@kernel.org>
Acked-by: Sam Ravnborg <sam@ravnborg.org>
Tested-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200226112514.12455-12-laurent.pinchart@ideasonboard.com
The dumb-vga-dac driver is a simple DRM bridge driver for simple VGA
DACs that don't require configuration. Other non-VGA bridges fall in a
similar category, and would benefit from a common driver. Prepare for
this by renaming the internal symbols from dumb-vga-dac to
simple-bridge.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Andrzej Hajda <a.hajda@samsung.com>
Reviewed-by: Boris Brezillon <boris.brezillon@collabora.com>
Reviewed-by: Maxime Ripard <mripard@kernel.org>
Acked-by: Sam Ravnborg <sam@ravnborg.org>
Tested-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200226112514.12455-11-laurent.pinchart@ideasonboard.com
Most bridge drivers create a DRM connector to model the connector at the
output of the bridge. This model is historical and has worked pretty
well so far, but causes several issues:
- It prevents supporting more complex display pipelines where DRM
connector operations are split over multiple components. For instance a
pipeline with a bridge connected to the DDC signals to read EDID data,
and another one connected to the HPD signal to detect connection and
disconnection, will not be possible to support through this model.
- It requires every bridge driver to implement similar connector
handling code, resulting in code duplication.
- It assumes that a bridge will either be wired to a connector or to
another bridge, but doesn't support bridges that can be used in both
positions very well (although there is some ad-hoc support for this in
the analogix_dp bridge driver).
In order to solve these issues, ownership of the connector should be
moved to the display controller driver (where it can be implemented
using helpers provided by the core).
Extend the bridge API to allow disabling connector creation in bridge
drivers as a first step towards the new model. The new flags argument to
the bridge .attach() operation allows instructing the bridge driver to
skip creating a connector. Unconditionally set the new flags argument to
0 for now to keep the existing behaviour, and modify all existing bridge
drivers to return an error when connector creation is not requested as
they don't support this feature yet.
The change is based on the following semantic patch, with manual review
and edits.
@ rule1 @
identifier funcs;
identifier fn;
@@
struct drm_bridge_funcs funcs = {
...,
.attach = fn
};
@ depends on rule1 @
identifier rule1.fn;
identifier bridge;
statement S, S1;
@@
int fn(
struct drm_bridge *bridge
+ , enum drm_bridge_attach_flags flags
)
{
... when != S
+ if (flags & DRM_BRIDGE_ATTACH_NO_CONNECTOR) {
+ DRM_ERROR("Fix bridge driver to make connector optional!");
+ return -EINVAL;
+ }
+
S1
...
}
@ depends on rule1 @
identifier rule1.fn;
identifier bridge, flags;
expression E1, E2, E3;
@@
int fn(
struct drm_bridge *bridge,
enum drm_bridge_attach_flags flags
) {
<...
drm_bridge_attach(E1, E2, E3
+ , flags
)
...>
}
@@
expression E1, E2, E3;
@@
drm_bridge_attach(E1, E2, E3
+ , 0
)
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Boris Brezillon <boris.brezillon@collabora.com>
Acked-by: Sam Ravnborg <sam@ravnborg.org>
Reviewed-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Tested-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200226112514.12455-10-laurent.pinchart@ideasonboard.com
Propagate bus format/flags so that the previous bridge element in the
chain knows which input format the panel bridge expects.
v11:
* Fix a typo in the subject
* Update the commit message so it's readable by itself
v10:
* Add changelog to the commit message
v8 -> v9:
* No changes
v7:
* Set atomic state hooks explicitly
v4 -> v6:
* Not part of the series
v3:
* Adjust things to match the new bus-format negotiation approach
* Use drm_atomic_helper_bridge_propagate_bus_fmt
* Don't implement ->atomic_check() (the core now takes care of bus
flags propagation)
v2:
* Adjust things to match the new bus-format negotiation approach
Signed-off-by: Boris Brezillon <boris.brezillon@collabora.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200128135514.108171-11-boris.brezillon@collabora.com
The drm_bridge_funcs structure is never modified, make it const. Making
it read-only can improve security as the structure contains function
pointers.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Reviewed-by: Boris Brezillon <boris.brezillon@collabora.com>
Signed-off-by: Boris Brezillon <boris.brezillon@collabora.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200224230056.2157-1-laurent.pinchart+renesas@ideasonboard.com
Factor out the manual container_of() uses to a common to_lvds_codec()
macro to shorten lines (and provide better type safety, although that
won't matter much in this case).
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Reviewed-by: Boris Brezillon <boris.brezillon@collabora.com>
Signed-off-by: Boris Brezillon <boris.brezillon@collabora.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200224225645.28060-1-laurent.pinchart+renesas@ideasonboard.com
of_get_regulator() will unconditionally add "-supply" to form the
property name. This is documented in commit 69511a452e ("map consumer
regulator based on device tree"). Remove the suffix from the requests.
Signed-off-by: Torsten Duwe <duwe@lst.de>
Reviewed-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Link: https://patchwork.freedesktop.org/patch/msgid/20200218155440.BEFB968C65@verein.lst.de
Based on work by Bjorn Andersson <bjorn.andersson@linaro.org>,
Jeffrey Hugo <jeffrey.l.hugo@gmail.com>, and
Rob Clark <robdclark@chromium.org>.
Let's read the SUPPORTED_LINK_RATES and/or MAX_LINK_RATE (depending on
the eDP version of the sink) to figure out what eDP rates are
supported and pick the ideal one.
NOTE: I have only personally tested this code on eDP panels that are
1.3 or older. Code reading SUPPORTED_LINK_RATES for DP 1.4+ was
tested by hacking the code to pretend that a table was there.
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191218143416.v3.9.Ib59207b66db377380d13748752d6fce5596462c5@changeid
If we fail training at a lower DP link rate let's now keep trying
until we run out of rates to try. Basically the algorithm here is to
start at the link rate that is the theoretical minimum and then slowly
bump up until we run out of rates or hit the max rate of the sink. We
query the sink using a DPCD read.
This is, in fact, important in practice. Specifically at least one
panel hooked up to the bridge (AUO B116XAK01) had a theoretical min
rate more than 1.62 GHz (if run at 24 bpp) and fails to train at the
next rate (2.16 GHz). It would train at 2.7 GHz, though.
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Tested-by: Rob Clark <robdclark@gmail.com>
Reviewed-by: Rob Clark <robdclark@gmail.com>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191218143416.v3.8.I251add713bc5c97225200894ab110ea9183434fd@changeid
Biju Das