Sony VGN-BX297XP fails suspend if the controller is powered down when
calling into ACPI suspend. Add the machine to piix_broken_suspend
list.
This problem was reported by GNUtoo@no-log.org on bko#10293.
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Rafael J. Wysocki <rjw@sisk.pl>
Reported-by: GNUtoo@no-log.org
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Samsung DB-P70 somehow botched the first ICH9 SATA port. The board
doesn't expose the first port but somehow SStatus reports link online
while failing SRST protocol leading to repeated probe failures and
thus long boot delay.
Because the BIOS doesn't carry any identifying DMI information, the
port can't be blacklisted safely. Fortunately, the controller does
have subsystem vendor and ID set. It's unclear whether the subsystem
IDs are used only for the board but it can be safely worked around by
disabling SIDPR access and just using SRST works around the problem.
Even when the workaround is triggered on an unaffected board the only
side effect will be missing SCR access.
Signed-off-by: Tejun Heo <tj@kernel.org>
Reported-by: Joseph Jang <josephjang@gmail.com>
Reported-by: Jonghyon Sohn <mrsohn@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Some notebooks from HP have the problem that their BIOSes attempt to
spin down hard drives before entering ACPI system states S4 and S5.
This leads to a yo-yo effect during system power-off shutdown and the
last phase of hibernation when the disk is first spun down by the
kernel and then almost immediately turned on and off by the BIOS.
This, in turn, may result in shortening the disk's life times.
To prevent this from happening we can blacklist the affected systems
using DMI information.
Blacklist HP 2510p that uses the ata_piix driver.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
This matters for some controllers and in one or two cases almost doubles
PIO performance. Add a bmdma32 operations set we can inherit and activate
it for some controllers
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Certain ACPI implementations mess up IOCFG on _STM making libata
detect cable type incorrectly after a suspend/resume cycle. This
patch makes ata_piix save IOCFG on attach, use the saved value for
things which aren't dynamic and restore it on detach so that the next
driver also gets the BIOS initialized value.
This patch contains the following changes.
* makes ich_pata_cable_detect() use saved_iocfg.
* make piix_iocfg_bit18_quirk() take @host and use saved_iocfg.
* hpriv allocation moved upwards to save iocfg before doing anything
else.
This fixes bz#11879. Andreas Mohr reported and diagnosed the problem.
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Andreas Mohr <andi@lisas.de>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Commit
ATA: piix, fix pointer deref on suspend
fixed a possible oops in an ugly manner. Use newly introduced dmi_match()
to make the code pretty again.
Signed-off-by: Jiri Slaby <jirislaby@gmail.com>
Cc: Alexandru Romanescu <a_romanescu@yahoo.co.uk>
Cc: Tejun Heo <tj@kernel.org>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Hi,
I've found this issue in the mmotm 2008-12-02-17-08.
--
Commit
ata_piix: add borked Tecra M4 to broken suspend list
introduced DMI variables checking, but they can be null, so that
we possibly dereference null.
Check if they are null and avoid checks in that case.
Solves:
BUG: unable to handle kernel NULL pointer dereference at 0000000000000000
IP: [<ffffffff8043da97>] piix_pci_device_suspend+0x117/0x230
Signed-off-by: Jiri Slaby <jirislaby@gmail.com>
Cc: Jeff Garzik <jgarzik@redhat.com>
Cc: Alexandru Romanescu <a_romanescu@yahoo.co.uk>
Cc: Tejun Heo <tj@kernel.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Tecra M4 sometimes forget what it is and reports bogus data via DMI
which makes the machine evade broken suspend matching and thus fail
suspend/resume. This patch updates piix_broken_suspend() such that it
can match such case. As the borked DMI data is a bit generic,
matching many entries to make the match more specific is necessary.
As the usual DMI matching is limited to four entries, this patch uses
hard coded manual matching.
This is reported by Alexandru Romanescu.
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Alexandru Romanescu <a_romanescu@yahoo.co.uk>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Remove excess kernel-doc function parameter notation from drivers/ata/:
Warning(drivers/ata/libata-core.c:1622): Excess function parameter or struct member 'fn' description in 'ata_pio_queue_task'
Warning(drivers/ata/libata-core.c:4655): Excess function parameter or struct member 'err_mask' description in 'ata_qc_complete'
Warning(drivers/ata/ata_piix.c:751): Excess function parameter or struct member 'udma' description in 'do_pata_set_dmamode'
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
This patch updates the Intel Ibex Peak (PCH) IDE mode SATA Controller DeviceIDs.
Signed-off-by: Seth Heasley <seth.heasley@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Now that libata has slave_link, there's no need to keep ugly merged
SCR access. Drop it and use slave_link instead. This results in
simpler code and much better separate link handling for master and
slave.
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Logically, SCR access ops should take @link; however, there was no
compelling reason to convert all SCR access ops when adding @link
abstraction as there's one-to-one mapping between a port and a non-PMP
link. However, that assumption won't hold anymore with the scheduled
addition of slave link.
Make SCR access ops per-link.
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
drivers/ata/ata_piix.c:1502:7: warning: symbol 'rc' shadows an earlier one
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
This patch adds the Intel Ibex Peak (PCH) IDE mode SATA Controller DeviceIDs.
Signed-off-by: Seth Heasley <seth.heasley@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Subsys 106b:00a3 also is the weird apple ich8m which chokes when the
latter two ports are accessed, add it. Reported by Felipe Sere.
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Felipe Sere <dodofxp@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
TOSHIBA also used "TECRA M4" in additon to "Tecra M4", add it.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Add ICH6 on ACER Aspire 1694WLMi to list of laptops that use short cables
rather than 80 wire
OriginalAuthor: Tiago Sousa
OriginalLocation: http://launchpadlibrarian.net/11627664/new.ich_laptop.short.cables.diff
Bug: #187121
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: maximilian attems <max@stro.at>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
ICH8M on macbooks are peculiar in that some of them lock up when the
second port is enabled, some return bogus values on SIDPR access while
yet others hang on SIDPR access. Also, the ich8m_apple_sata entry was
wrongly added below generic ich8m entry making it virtually useless.
This patch works around macbook ich8m problems by
* moving ich8m_apple_sata entry above generic ich8m entry
* dropping PIIX_FLAG_SIDPR from ich8m_apple_sata
* adding subsystem 106b:00a1 as ich8m_apple_sata
Reported and tested by MATSUBAYASHI.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Cc: MATSUBAYASHI 'Shaolin' Kohji <shaolin@rhythmaning.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
On certain configurations (certain macbooks), even though all the
conditions for SIDPR access described in the datasheet are met,
actually reading those registers just returns 0 and have no effect on
write. Verify SIDPR is actually working before enabling it.
This is reported by Ryan Roth in bz#10512.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Cc: Ryan Roth <ryan.roth@ch2m.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
The drive is directly soldered to the controller, so there is no cable at
all. Remove the 40-wire assumption so the drive can operate at max speed.
Before patch:
$ dd if=/dev/sda of=/dev/null bs=2M count=64 iflag=direct
134217728 bytes (134 MB) copied, 5.29612 s, 25.3 MB/s
After patch:
$ dd if=/dev/sda of=/dev/null bs=2M count=64 iflag=direct
134217728 bytes (134 MB) copied, 3.94955 s, 34.0 MB/s
Signed-off-by: Dan McGee <dpmcgee@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Implement sata_std_hardreset(), which simply wraps around
sata_link_hardreset(). sata_std_hardreset() becomes new standard
hardreset method for sata_port_ops and sata_sff_hardreset() moves from
ata_base_port_ops to ata_sff_port_ops, which is where it really
belongs.
ata_is_builtin_hardreset() is added so that both
ata_std_error_handler() and ata_sff_error_handler() skip both builtin
hardresets if SCR isn't accessible.
piix_sidpr_hardreset() in ata_piix.c is identical to
sata_std_hardreset() in functionality and got replaced with the
standard function.
Signed-off-by: Tejun Heo <htejun@gmail.com>
sata_sff_hardreset() contains link readiness wait logic which isn't
SFF specific. Move that part into sata_link_hardreset(), which now
takes two more parameters - @online and @check_ready. Both are
optional. The former is out parameter for link onlineness after
reset. The latter is used to wait for link readiness after hardreset.
Users of sata_link_hardreset() is updated to use new funtionality and
ahci_hardreset() is updated to use sata_link_hardreset() instead of
sata_sff_hardreset(). This doesn't really cause any behavior change.
Signed-off-by: Tejun Heo <htejun@gmail.com>
SFF functions have confusing names. Some have sff prefix, some have
bmdma, some std, some pci and some none. Unify the naming by...
* SFF functions which are common to both BMDMA and non-BMDMA are
prefixed with ata_sff_.
* SFF functions which are specific to BMDMA are prefixed with
ata_bmdma_.
* SFF functions which are specific to PCI but apply to both BMDMA and
non-BMDMA are prefixed with ata_pci_sff_.
* SFF functions which are specific to PCI and BMDMA are prefixed with
ata_pci_bmdma_.
* Drop generic prefixes from LLD specific routines. For example,
bfin_std_dev_select -> bfin_dev_select.
The following renames are noteworthy.
ata_qc_issue_prot() -> ata_sff_qc_issue()
ata_pci_default_filter() -> ata_bmdma_mode_filter()
ata_dev_try_classify() -> ata_sff_dev_classify()
This rename is in preparation of separating SFF support out of libata
core layer. This patch strictly renames functions and doesn't
introduce any behavior difference.
Signed-off-by: Tejun Heo <htejun@gmail.com>
ich6_sata_ahci and ich6_sata are identical. Kill ich6_sata_ahci and
drop _ahci postfixes from controller ids, which doesn't really mean
anything at this point.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
ata_piix when attached to ICH6M in AHCI mode doesn't provide any
benefit over using ahci and has detection problems. Don't let
ata_piix claim ICH6M if it's in AHCI mode.
This change makes ICH6R the only one which ata_piix can attach to even
when it's in ahci mode which is necessary as some devices don't work
properly under ahci mode. Drop PIIX_FLAG_AHCI and match the
controller directly so that piix_disable_ahci() is called only for it.
This change makes PIIX_SCC no longer used and it gets dropped too.
This fixes bz 9491.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Cc: Robert M. Albrecht <romal@gmx.de>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Currently reset methods are not specified directly in the
ata_port_operations table. If a LLD wants to use custom reset
methods, it should construct and use a error_handler which uses those
reset methods. It's done this way for two reasons.
First, the ops table already contained too many methods and adding
four more of them would noticeably increase the amount of necessary
boilerplate code all over low level drivers.
Second, as ->error_handler uses those reset methods, it can get
confusing. ie. By overriding ->error_handler, those reset ops can be
made useless making layering a bit hazy.
Now that ops table uses inheritance, the first problem doesn't exist
anymore. The second isn't completely solved but is relieved by
providing default values - most drivers can just override what it has
implemented and don't have to concern itself about higher level
callbacks. In fact, there currently is no driver which actually
modifies error handling behavior. Drivers which override
->error_handler just wraps the standard error handler only to prepare
the controller for EH. I don't think making ops layering strict has
any noticeable benefit.
This patch makes ->prereset, ->softreset, ->hardreset, ->postreset and
their PMP counterparts propoer ops. Default ops are provided in the
base ops tables and drivers are converted to override individual reset
methods instead of creating custom error_handler.
* ata_std_error_handler() doesn't use sata_std_hardreset() if SCRs
aren't accessible. sata_promise doesn't need to use separate
error_handlers for PATA and SATA anymore.
* softreset is broken for sata_inic162x and sata_sx4. As libata now
always prefers hardreset, this doesn't really matter but the ops are
forced to NULL using ATA_OP_NULL for documentation purpose.
* pata_hpt374 needs to use different prereset for the first and second
PCI functions. This used to be done by branching from
hpt374_error_handler(). The proper way to do this is to use
separate ops and port_info tables for each function. Converted.
Signed-off-by: Tejun Heo <htejun@gmail.com>
libata lets low level drivers build ata_port_operations table and
register it with libata core layer. This allows low level drivers
high level of flexibility but also burdens them with lots of
boilerplate entries.
This becomes worse for drivers which support related similar
controllers which differ slightly. They share most of the operations
except for a few. However, the driver still needs to list all
operations for each variant. This results in large number of
duplicate entries, which is not only inefficient but also error-prone
as it becomes very difficult to tell what the actual differences are.
This duplicate boilerplates all over the low level drivers also make
updating the core layer exteremely difficult and error-prone. When
compounded with multi-branched development model, it ends up
accumulating inconsistencies over time. Some of those inconsistencies
cause immediate problems and fixed. Others just remain there dormant
making maintenance increasingly difficult.
To rectify the problem, this patch implements ata_port_operations
inheritance. To allow LLDs to easily re-use their own ops tables
overriding only specific methods, this patch implements poor man's
class inheritance. An ops table has ->inherits field which can be set
to any ops table as long as it doesn't create a loop. When the host
is started, the inheritance chain is followed and any operation which
isn't specified is taken from the nearest ancestor which has it
specified. This operation is called finalization and done only once
per an ops table and the LLD doesn't have to do anything special about
it other than making the ops table non-const such that libata can
update it.
libata provides four base ops tables lower drivers can inherit from -
base, sata, pmp, sff and bmdma. To avoid overriding these ops
accidentaly, these ops are declared const and LLDs should always
inherit these instead of using them directly.
After finalization, all the ops table are identical before and after
the patch except for setting .irq_handler to ata_interrupt in drivers
which didn't use to. The .irq_handler doesn't have any actual effect
and the field will soon be removed by later patch.
* sata_sx4 is still using old style EH and currently doesn't take
advantage of ops inheritance.
Signed-off-by: Tejun Heo <htejun@gmail.com>
libata lets low level drivers build scsi_host_template and register it
to the SCSI layer. This allows low level drivers high level of
flexibility but also burdens them with lots of boilerplate entries.
This patch implements SHT initializers which can be used to initialize
all the boilerplate entries in a sht. Three variants of them are
implemented - BASE, BMDMA and NCQ - for different types of drivers.
Note that entries can be overriden by putting individual initializers
after the helper macro.
All sht tables are identical before and after this patch.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Over the time, port info, ops and sht structures developed quite a bit
of inconsistencies. This patch updates drivers.
* Enable/disable_pm callbacks added to all ahci ops tables.
* Every driver for SFF controllers now uses ata_sff_port_start()
instead of ata_port_start() unless the driver has custom
implementation.
* Every driver for SFF controllers now uses ata_pci_default_filter()
unless the driver has custom implementation.
* Removed an odd port_info->sht initialization from ata_piix.c.
Likely a merge byproduct.
* A port which has ATA_FLAG_SATA set doesn't need to set cable_detect
to ata_cable_sata(). Remove it from via and mv port ops.
* Some drivers had unnecessary .max_sectors initialization which is
ignored and was missing .slave_destroy callback. Fixed.
* Removed unnecessary sht initializations port_info's.
* Removed onsolete scsi device suspend/resume callbacks from
pata_bf54x.
* No reason to set ata_pci_default_filter() and bmdma functions for
PIO-only drivers. Remove those callbacks and replace
ata_bmdma_irq_clear with ata_noop_irq_clear.
* pata_platform sets port_start to ata_dummy_ret0. port_start can
just be set to NULL.
* sata_fsl supports NCQ but was missing qc_defer. Fixed.
* pata_rb600_cf implements dummy port_start. Removed.
Signed-off-by: Tejun Heo <htejun@gmail.com>
During the last step of hibernation in the "platform" mode (with the
help of ACPI) we use the suspend code, including the devices'
->suspend() methods, to prepare the system for entering the ACPI S4
system sleep state.
But at least for some devices the operations performed by the
->suspend() callback in that case must be different from its operations
during regular suspend.
For this reason, introduce the new PM event type PM_EVENT_HIBERNATE and
pass it to the device drivers' ->suspend() methods during the last phase
of hibernation, so that they can distinguish this case and handle it as
appropriate. Modify the drivers that handle PM_EVENT_SUSPEND in a
special way and need to handle PM_EVENT_HIBERNATE in the same way.
These changes are necessary to fix a hibernation regression related
to the i915 driver (ref. http://lkml.org/lkml/2008/2/22/488).
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: Pavel Machek <pavel@ucw.cz>
Tested-by: Jeff Chua <jeff.chua.linux@gmail.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
drivers/ata/ata_piix.c:1655:8: warning: symbol 'rc' shadows an earlier one
drivers/ata/ata_piix.c:1616:6: originally declared here
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
This patch fixes the following section mismatches:
<-- snip -->
...
WARNING: drivers/ata/built-in.o(.text+0x15072): Section mismatch in reference from the function piix_init_one() to the function .devinit.text:piix_init_sata_map()
WARNING: drivers/ata/built-in.o(.text+0x150dd): Section mismatch in reference from the function piix_init_one() to the function .devinit.text:piix_init_pcs()
WARNING: drivers/ata/built-in.o(.text+0x150e5): Section mismatch in reference from the function piix_init_one() to the function .devinit.text:piix_init_sidpr()
WARNING: drivers/ata/built-in.o(.text+0x15107): Section mismatch in reference from the function piix_init_one() to the function .devinit.text:piix_check_450nx_errata()
...
<-- snip -->
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
This patch adds the Intel ICH10 IDE mode SATA Controller DeviceID's.
Signed-off-by: Jason Gaston <jason.d.gaston@intel.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
For ICH8, SCRs can be accessed using index and data register pair
located at BAR 5. This patch implements support for it such that PHY
status, errors and hardreset are available for those controllers.
This is the only case where two devices on a PATA channel have access
to SCRs and creates a unique problem of mapping two SCRs to one link.
Note that this is different from PMP case in that they aren't quite
separate links - e.g. softreset resets both devices.
This problem is worked around by merging the SCR values. To upper
layer, it looks like there is a single link with one set of SCRs but
with two devices. This works well enough for PHY event, error
reporting and hardreset.
Supporting hardreset is important because in rare cases SATA devices
fail to recover without it after PHY errors.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
ata_piix requires more configuration during initialization than most
other SFF compliant controllers and one-go initialzation with
ata_pci_one() is too rigid.
This patch converts ata_piix to use two step prepare - activate
initialization used by other more advanced controllers. This
conversion brings the happy side effect of enabling PCI device before
accessing PCI configuration registers. Other than that, there
shouldn't be any behavior change.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Kill PIIX_FLAG_SCR, PIIX_PORT_ENABLED and PIIX_PORT_PRESENT. These
are unused.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Separate controller IDs into a separate enum as Jeff requested.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Add Toshiba Satellite R20 and Tecra M6 to broken suspend list. Matt
Piermarini reported and provided the M6 patch. This is from OSDL bug 7780.
Signed-off-by: Peter Schwenke <peter@bluetoad.com.au>
Cc: Matt Piermarini <mattpiermarini@yahoo.com>
Acked-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Add Toshiba Tecra M4 to broken suspend list. This is from OSDL
bugzilla bug 7780.
Signed-off-by: Peter Schwenke <peter@bluetoad.com.au>
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Add more toshiba laptops to broken suspend list. This is from OSDL
bugzilla bug 7780.
tj: re-formatted patch and added description and SOB.
Signed-off-by: Peter Schwenke <peter@bluetoad.com.au>
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
ICH8 and 9 use two SFF controllers to show 6 SATA ports. The first
controllre hosts the first 4 ports while the second one hosts the last
2. The PCS register of the first controller encompasses the first
four ports or all six ports depending on configuration while PCS of
the second controller controls the last two ports. Using 0xf for the
first controller and 0x3 for the second controller always result in
the correct configuration.
Signed-off-by: Tejun Heo <htejun@gmail.com>
ICH8M on apple macbook pro occasionally locks up completely during PCS
initialization if ports other than the first one are enabled. Add a
separate controller ID and only enable the first port.
tj: commit description added and patch updated to fit with the
previous controller ID update.
Signed-off-by: Thomas Rohwer <tr@tng.de>
Signed-off-by: Tejun Heo <htejun@gmail.com>
Move piix_pata_mwdma to top, rename ich9_2port_sata to ich8_2port_sata
for consistency and use automatically incremented values instead of
assigning fixed values to ease adding new controller IDs.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Satellite U205 has alternate product name where the satellite part is
all capatalized. Add it to the blacklist.
This is reported by Ross Patterson in kernel bugzilla bug #7780.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Cc: Ross Patterson <me@rpatterson.net>
Please warmly welcome the PRO variant of Satellite U200 to the broken
suspend list.
Original patch is from Yann Chachkoff. Patch reformatted and
forwarded by Tejun Heo.
Signed-off-by: Yann Chachkoff <yann.chachkoff@myrealbox.com>
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Keeping the list in sync with the old IDE driver
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Tackle the relatively sane complaints of checkpatch --file.
The vast majority is indentation and whitespace changes, the rest are
* #include fixes
* printk KERN_xxx prefix addition
* BSS/initializer cleanups
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
This patch adds a port map for ICH9 and ICH8 SATA controllers that have only 2 ports available in that mode.
Signed-off-by: Jason Gaston <jason.d.gaston@intel.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
This patch removes some incorrect formatting spaces and replaces them with tabs.
Signed-off-by: Jason Gaston <jason.d.gaston@intel.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
It was always set to ata_port_disable(). Removed the hook, and replaced
the very few ap->ops->port_disable() callsites with direct calls to
ata_port_disable().
Signed-off-by: Jeff Garzik <jeff@garzik.org>
* ->irq_ack() is redundant to what the irq handler already
performs... chk-status + irq-clear. Furthermore, it is only
called in one place, when screaming-irq-debugging is enabled,
so we don't want to bother with a hook just for that.
* ata_dummy_irq_on() is only ever used in drivers that have
no callpath reaching ->irq_on(). Remove .irq_on hook from
those drivers, and the now-unused ata_dummy_irq_on()
Signed-off-by: Jeff Garzik <jeff@garzik.org>
There is another outstanding issue with ata_piix.c. Intel has never
officially supported anything faster than PATA 100MB/s.
But, the ata_piix.c driver "define" the ICH5 & ICH7 as UDMA6 (aka 133MB/s)
capable. [ Well, no one has probably noticed it before, because there is bug
in do_pata_set_dmamode... Just look at
libata_atapiix_enable_real_udma133.patch and you'll see what wrong with it. ]
Here are Intel's datasheets for the affected chipsets: ICH5 Datasheet:
http://www.intel.com/design/chipsets/datashts/252516.htm (See note on page
183: "... the ICH5 supports reads at the maximum rate of 100MB/s.")
ICH7 Datasheet: http://www.intel.com/design/chipsets/datashts/307013.htm (See
first note on page 190: "... the ICH7 supports reads at the maximum rate of
100MB/s.")
They are two different ways to deal with it:
- Either -
1. replace all ich_pata_133 with ich_pata_100.
(libata_atapiix_disable_udma6.diff - diff from 2.6.22 )
- Or -
2. keep all ich_pata_133 and fix the bug in "do_pata_set_dmamode".
(libata_atapiix_enable_real_udma133.patch - diff from 2.6.22) If there are
any concerns about the safety of the patch patch:
http://lkml.org/lkml/2007/7/6/292 (It was already tested by an Intel
employee, but I guess a bit more user input is necessary here... )
This patch implements 1.
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Cc: Jeff Garzik <jeff@garzik.org>
Cc: Tejun Heo <htejun@gmail.com>
Signed-off-by: Christian Lamparter <chunkeey@web.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Make reset methods and related functions deal with ata_link instead of
ata_port.
* ata_do_reset()
* ata_eh_reset()
* all prereset/reset/postreset methods and related functions
This patch introduces no behavior change.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Three main sets of changes:
1) dmi_get_system_info() return value should have been marked const,
since callers should not be changing that data.
2) const-ify DMI internals, since DMI firmware tables should,
whenever possible, be marked const to ensure we never ever write to
that data area.
3) const-ify DMI API, to enable marking tables const where possible
in low-level drivers.
And if we're really lucky, this might enable some additional
optimizations on the part of the compiler.
The bulk of the changes are #2 and #3, which are interrelated. #1 could
have been a separate patch, but it was so small compared to the others,
it was easier to roll it into this changeset.
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
There's a different version of DMI table for TECRA M3 where it has
proper vendor and product name entry. Add the entry to the broken
suspend list.
Angus Turnbull reported and provided initial patch.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Cc: Angus Turnbull <angus@twinhelix.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Some notebooks need bit18 of IOCFG to be cleared for the drive bay to
work even though the bit is NOOP according to the datasheet. This
patch implement IOCFG bit18 quirk and apply it to Clevo M570U.
http://bugzilla.kernel.org/show_bug.cgi?id=8051
Signed-off-by: Tejun Heo <htejun@gmail.com>
Cc: D. Angelis <dangelis@beta-cae.gr>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Satellite U200 also shares the problem. Add it to the broken suspend
list. Original patch from John Schember.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Cc: John Schember <john@nachtimwald.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Resend trying to remove 8-bit characters in the email.
This patch adds the Intel Tolapai IDE mode SATA controller DID's.
Signed-off-by: Jason Gaston <jason.d.gaston@intel.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Add TECRA M7 to broken suspend list. Reported by Marie Koreen.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Cc: Marie Koreen <kbug@koreen.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Add Tecra M3 to the broken suspend blacklist. Tecra M3 doesn't have
proper DMI_PRODUCT_NAME but has an OEM_STRING instead. Match it.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Separate out broken suspend blacklist matching into
piix_broken_suspend().
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
ACPI implementations in several TOSHIBA laptops are weird and burn cpu
cycles for tens of seconds while trying to suspend if the PCI device
for the ATA controller is disabled when the ACPI suspend is called.
This patch uses DMI to match those machines and bypass device disable
on those machines during suspend. As the device needs to be put into
enabled state on resume without affecting PCI enable count, matching
resume callback uses __pci_reenable_device().
This bug is reported in bugzilla bug 7780.
http://bugzilla.kernel.org/show_bug.cgi?id=7780
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
* master.kernel.org:/pub/scm/linux/kernel/git/gregkh/pci-2.6: (34 commits)
PCI: Only build PCI syscalls on architectures that want them
PCI: limit pci_get_bus_and_slot to domain 0
PCI: hotplug: acpiphp: avoid acpiphp "cannot get bridge info" PCI hotplug failure
PCI: hotplug: acpiphp: remove hot plug parameter write to PCI host bridge
PCI: hotplug: acpiphp: fix slot poweroff problem on systems without _PS3
PCI: hotplug: pciehp: wait for 1 second after power off slot
PCI: pci_set_power_state(): check for PM capabilities earlier
PCI: cpci_hotplug: Convert to use the kthread API
PCI: add pci_try_set_mwi
PCI: pcie: remove SPIN_LOCK_UNLOCKED
PCI: ROUND_UP macro cleanup in drivers/pci
PCI: remove pci_dac_dma_... APIs
PCI: pci-x-pci-express-read-control-interfaces cleanups
PCI: Fix typo in include/linux/pci.h
PCI: pci_ids, remove double or more empty lines
PCI: pci_ids, add atheros and 3com_2 vendors
PCI: pci_ids, reorder some entries
PCI: i386: traps, change VENDOR to DEVICE
PCI: ATM: lanai, change VENDOR to DEVICE
PCI: Change all drivers to use pci_device->revision
...
The last two slots of MAP 00b of ich6m was incorrectly marked as
reserved. This is left over from converting the entry to allow 00b.
This causes no real problem. It only makes the driver print annoying
warning message. Fix it.
[patch also proferred by Pierre Tardy at the end of 2006 -jg]
Signed-off-by: Tejun Heo <htejun@gmail.com>
--
drivers/ata/ata_piix.c | 2 +-
1 file changed, 1 insertion(+), 1 deletion(-)
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Instead of all drivers reading pci config space to get the revision
ID, they can now use the pci_device->revision member.
This exposes some issues where drivers where reading a word or a dword
for the revision number, and adding useless error-handling around the
read. Some drivers even just read it for no purpose of all.
In devices where the revision ID is being copied over and used in what
appears to be the equivalent of hotpath, I have left the copy code
and the cached copy as not to influence the driver's performance.
Compile tested with make all{yes,mod}config on x86_64 and i386.
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Acked-by: Dave Jones <davej@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The ATA_UDMAx masks are self-documenting, and far better than manually
writing in the hex mask.
Note that pata_it8213 mask differed from the comment. Added a FIXME there.
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Fix various bugs in pio/mwdma mode programming.
* Control bits in the timing register wasn't cleared properly while
programming PIO mode.
* MWDMA mode programming cleared the wrong part of control bits.
* MWDMA mode programming cleared udma_mask even when the controller
doesn't support UDMA.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Cc: Art Haas <ahaas@airmail.net>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Acer Aspire 2023WLMi uses short 40c cable. Add quirk for it.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Cc: Steve H. <mail.pandor@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
With cable methods in place we don't need a custom error handler for SATA
so get rid of it
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The intention of using port_mask in SFF init helpers was to eventually
support exoctic configurations such as combination of legacy and
native port on the same controller. This never became actually
necessary and the related code always has been subtly broken one way
or the other. Now that new init model is in place, there is no reason
to make common helpers capable of handling all corner cases. Exotic
cases can simply dealt within LLDs as necessary.
This patch removes port_mask handling in SFF init helpers. SFF init
helpers don't take n_ports argument and interpret it into port_mask
anymore. All information is carried via port_info. n_ports argument
is dropped and always two ports are allocated. LLD can tell SFF to
skip certain port by marking it dummy. Note that SFF code has been
treating unuvailable ports this way for a long time until recent
breakage fix from Linus and is consistent with how other drivers
handle with unavailable ports.
This fixes 1-port legacy host handling still broken after the recent
native mode fix and simplifies SFF init logic. The following changes
are made...
* ata_pci_init_native_host() and ata_init_legacy_host() both now try
to initialized whatever they can and mark failed ports dummy. They
return 0 if any port is successfully initialized.
* ata_pci_prepare_native_host() and ata_pci_init_one() now doesn't
take n_ports argument. All info should be specified via port_info
array. Always two ports are allocated.
* ata_pci_init_bmdma() exported to be used by LLDs in exotic cases.
* port_info handling in all LLDs are standardized - all port_info
arrays are const stack variable named ppi. Unless the second port
is different from the first, its port_info is specified as NULL
(tells libata that it's identical to the last non-NULL port_info).
* pata_hpt37x/hpt3x2n: don't modify static variable directly. Make an
on-stack copy instead as ata_piix does.
* pata_uli: It has 4 ports instead of 2. Don't use
ata_pci_prepare_native_host(). Allocate the host explicitly and use
init helpers. It's simple enough.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Reimplement suspend/resume support using sdev->manage_start_stop.
* Device suspend/resume is now SCSI layer's responsibility and the
code is simplified a lot.
* DPM is dropped. This also simplifies code a lot. Suspend/resume
status is port-wide now.
* ata_scsi_device_suspend/resume() and ata_dev_ready() removed.
* Resume now has to wait for disk to spin up before proceeding. I
couldn't find easy way out as libata is in EH waiting for the
disk to be ready and sd is waiting for EH to complete to issue
START_STOP.
* sdev->manage_start_stop is set to 1 in ata_scsi_slave_config().
This fixes spindown on shutdown and suspend-to-disk.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Add @deadline to prereset and reset methods and make them honor it.
ata_wait_ready() which directly takes @deadline is implemented to be
used as the wait function. This patch is in preparation for EH timing
improvements.
* ata_wait_ready() never does busy sleep. It's only used from EH and
no wait in EH is that urgent. This function also prints 'be
patient' message automatically after 5 secs of waiting if more than
3 secs is remaining till deadline.
* ata_bus_post_reset() now fails with error code if any of its wait
fails. This is important because earlier reset tries will have
shorter timeout than the spec requires. If a device fails to
respond before the short timeout, reset should be retried with
longer timeout rather than silently ignoring the device.
There are three behavior differences.
1. Timeout is applied to both devices at once, not separately. This
is more consistent with what the spec says.
2. When a device passes devchk but fails to become ready before
deadline. Previouly, post_reset would just succeed and let
device classification remove the device. New code fails the
reset thus causing reset retry. After a few times, EH will give
up disabling the port.
3. When slave device passes devchk but fails to become accessible
(TF-wise) after reset. Original code disables dev1 after 30s
timeout and continues as if the device doesn't exist, while the
patched code fails reset. When this happens, new code fails
reset on whole port rather than proceeding with only the primary
device.
If the failing device is suffering transient problems, new code
retries reset which is a better behavior. If the failing device is
actually broken, the net effect is identical to it, but not to the
other device sharing the channel. In the previous code, reset would
have succeeded after 30s thus detecting the working one. In the new
code, reset fails and whole port gets disabled. IMO, it's a
pathological case anyway (broken device sharing bus with working
one) and doesn't really matter.
* ata_bus_softreset() is changed to return error code from
ata_bus_post_reset(). It used to return 0 unconditionally.
* Spin up waiting is to be removed and not converted to honor
deadline.
* To be on the safe side, deadline is set to 40s for the time being.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Versus upstream as requested
Last of the trivial switches to cable_detect methods.
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The Asus W5F laptop uses a short cable instead of the 80-wire style, and thus
needs to be in the ich_laptop special cases for correct detection and support
of UDMA/100 for the hard drive. I noticed this because I have the W5F laptop,
and was tracing apparent slowness.
Signed-off-by: Robin H. Johnson <robbat2@gentoo.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
A while ago I modified the libata code so that drivers can return -ENOENT
for unknown ports not fiddle with the EH flags and print stuff directly.
Somewhere along the line ata_piix didn't get fully converted.
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Add missing #ifdef CONFIG_PM conditionals around all PM related parts
in libata LLDs.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Duplicate ids noticed by Kay Sievers <kay.sievers@suse.de>
Although 100% different, this is based on a patch by Greg Kroah-Hartman
<gregkh@suse.de>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The ATA_ENABLE_PATA define was never meant to be permanent, and in
recent kernels, it's already been unconditionally enabled. Remove.
Signed-off-by: Jeff Garzik <jeff@garzik.org>
This patch is against each libata driver.
Two IRQ calls are added in ata_port_operations.
- irq_on() is used to enable interrupts.
- irq_ack() is used to acknowledge a device interrupt.
In most drivers, ata_irq_on() and ata_irq_ack() are used for
irq_on and irq_ack respectively.
In some drivers (ex: ahci, sata_sil24) which cannot use them
as is, ata_dummy_irq_on() and ata_dummy_irq_ack() are used.
Signed-off-by: Kou Ishizaki <kou.ishizaki@toshiba.co.jp>
Signed-off-by: Akira Iguchi <akira2.iguchi@toshiba.co.jp>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Convert libata core layer and LLDs to use iomap.
* managed iomap is used. Pointer to pcim_iomap_table() is cached at
host->iomap and used through out LLDs. This basically replaces
host->mmio_base.
* if possible, pcim_iomap_regions() is used
Most iomap operation conversions are taken from Jeff Garzik
<jgarzik@pobox.com>'s iomap branch.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Update libata LLDs to use devres. Core layer is already converted to
support managed LLDs. This patch simplifies initialization and fixes
many resource related bugs in init failure and detach path. For
example, all converted drivers now handle ata_device_add() failure
gracefully without excessive resource rollback code.
As most resources are released automatically on driver detach, many
drivers don't need or can do with much simpler ->{port|host}_stop().
In general, stop callbacks are need iff port or host needs to be given
commands to shut it down. Note that freezing is enough in many cases
and ports are automatically frozen before being detached.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
This I believe completes the PIIX range of support for libata
This adds the table entries needed for the PIIX3, both a new PCI
identifier and a new mode list. It also fixes an erroneous access to PCI
configuration 0x48 on non UDMA capable chips.
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
In Acer Aspire hdd is connected to ICH7 via 40c cable, however it is
short cable and it is UDMA66 capable.
Signed-off-by: J J <jakub007@go2.pl>
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Tejun Heo