Add HD Audio Device PCI ID for the Intel Broxton-T platform.
It is an HDA Intel PCH controller.
Signed-off-by: Lu, Han <han.lu@intel.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Although one weird behavior about the input path (inconsistent D0/D3
switch) on Cirrus CS420x codecs was fixed in the previous commit,
there is still an issue on some Mac machines: the capture stream
stalls when switching the ADCs on the fly. More badly, this keeps
stuck until the next reboot.
The dynamic ADC switching is already a bit fragile and assuming
optimistically that the chip accepts the frequent power changes. On
Cirrus codecs, this doesn't seem applicable.
As a quick workaround, we pin down the ADCs to keep up in D0 when
spec->dyn_adc_switch is set. In this way, the ADCs are kept up only
for the system that were confirmed to be broken.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=116171
Cc: <stable@vger.kernel.org> # v4.4+
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The Optiplex 9020m with Haswell-DT processor needs a quirk for the
headset jack at the front of the machine to be able to use microphones.
A quirk for this model was originally added in 3127899, but c77900e
removed it in favour of a more generic version.
Unfortunately, pin configurations can changed based on firmware/BIOS
versions, and the generic version doesn't have any effect on newer
versions of the machine/firmware anymore.
With help from David Henningsson <diwic@ubuntu.com>
Signed-off-by: Bastien Nocera <hadess@hadess.net>
Tested-by: Bastien Nocera <hadess@hadess.net>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Make sure per_pin is not NULL before using it.
Fixes: 9b3dc8aa3f ('ALSA: hda - Register chmap obj as priv data instead of codec')
Signed-off-by: Libin Yang <libin.yang@linux.intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
We've got a regression report that the recording on Mac with a cirrus
codec doesn't work any longer. This turned out to be the missing
power up to D0 by power_save_node enablement.
After analyzing the traces, we found out that the culprit is that the
codec advertises the "actual" power state of a few nodes to be D0
while the "target" power state is D3. This inconsistency is usually
OK, as it implies the power transition. But in the case of cirrus
codec, this seems to be stuck to D3 while it's not actually D0.
This patch addresses the issue by checking the power state difference
more strictly. It sends the power-state change verb unless both the
target and the actual power states show the given value.
We may introduce yet another flag indicating the possible broken
hardware power state, but it's anyway safer to set the proper power
state even in a transition (at least it's harmless as long as the
target state is same). So this simpler change was applied now.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=116171
Cc: <stable@vger.kernel.org> # v4.4+
Signed-off-by: Takashi Iwai <tiwai@suse.de>
While the previous commit fixed the missing monitor_present flag
update, it may be still in an inconsistent state while the driver
repolls: the flag itself is updated, but the eld_valid flag and the
contents don't follow until the repoll finishes (and may be repeated
for a few times).
The basic problem is that pin_eld->monitor_present is updated in the
caller side. This should have been updated only in update_eld(). So,
the proper fix is to avoid accessing pin_eld but only spec->temp_eld.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The commit [bd48128539ab: ALSA: hda - Fix forgotten HDMI
monitor_present update] covered the missing update of monitor_present
flag, but this caused a regression for devices without the i915 eld
notifier. Since the old code supposed that pin_eld->monitor_present
was updated by the caller side, the hdmi_present_sense_via_verbs()
doesn't update the temporary eld->monitor_present but only
pin_eld->monitor_present, which is now overridden in update_eld().
The fix is to update pin_eld->monitor_present as well before calling
update_eld().
Note that this may still leave monitor_present flag in an inconsistent
state when the driver repolls, but this is at least the old behavior.
More proper fix will follow in the later patch.
Fixes: bd48128539 ('ALSA: hda - Fix forgotten HDMI monitor_present update')
Signed-off-by: Hyungwon Hwang <hyungwon.hwang7@gmail.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The Lenovo Thinkpad T460s requires the alc_fixup_tpt440_dock as well in
order to get working sound output on the docking stations headphone jack.
Patch tested on a Thinkpad T460s (20F9CT01WW) using a ThinkPad Ultradock
on kernel 4.4.6.
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Tested-by: Simon Wunderlich <sw@simonwunderlich.de>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The front mic jack (pink color) can't detect any plug or unplug. After
applying this fix, both detecting function and recording function
work well.
BugLink: https://bugs.launchpad.net/bugs/1564712
Cc: stable@vger.kernel.org
Signed-off-by: Hui Wang <hui.wang@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This commit fixes garbled audio on Polaris-10/11 variants
Signed-off-by: Maruthi Bayyavarapu <maruthi.bayyavarapu@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Acked-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Apply the new fixup that is used for ASUS N750JV to another similar
model, N500JV, too, for reducing the headphone noise.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=115181
Signed-off-by: Bobi Mihalca <bobbymihalca@touchtech.ro>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
For reducing the noise from the headphone output on ASUS N750JV,
call the existing fixup, alc_fixup_auto_mute_via_amp(), additionally.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=115181
Signed-off-by: Bobi Mihalca <bobbymihalca@touchtech.ro>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
ASUS N750JV needs the same fixup as N550 for enabling its subwoofer.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=115181
Signed-off-by: Bobi Mihalca <bobbymihalca@touchtech.ro>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
i915 get_eld ops may return an error when no encoder is connected, and
currently we regard the error as fatal and skip the whole ELD
handling. This ended up with the missing ELD update at unplugging.
This patch fixes the issue by treating the error as the unplugged
state, instead of skipping the rest.
Reported-by: Libin Yang <libin.yang@linux.intel.com>
Cc: <stable@vger.kernel.org> # v4.5
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The recent addition of on-demand i915 audio component binding in the
codec driver seems leading to the unbalanced i915 power refcount,
according to Intel CI tests. Typically, it gets a kernel WARNING
like:
WARNING: CPU: 3 PID: 173 at sound/hda/hdac_i915.c:91 snd_hdac_display_power+0xf1/0x110 [snd_hda_core]()
Call Trace:
[<ffffffff813fef15>] dump_stack+0x67/0x92
[<ffffffff81078a21>] warn_slowpath_common+0x81/0xc0
[<ffffffff81078b15>] warn_slowpath_null+0x15/0x20
[<ffffffffa00f77e1>] snd_hdac_display_power+0xf1/0x110 [snd_hda_core]
[<ffffffffa015039d>] azx_intel_link_power+0xd/0x10 [snd_hda_intel]
[<ffffffffa011e32a>] azx_link_power+0x1a/0x30 [snd_hda_codec]
[<ffffffffa00f21f9>] snd_hdac_link_power+0x29/0x40 [snd_hda_core]
[<ffffffffa01192a6>] hda_codec_runtime_suspend+0x76/0xa0 [snd_hda_codec]
.....
The scenario is like below:
- HD-audio driver and i915 driver are probed concurrently at the
(almost) same time; HDA bus tries to bind with i915, but it fails
because i915 initialization is still being processed.
- Later on, HD-audio probes the HDMI codec, where it again tries to
bind with i915. At this time, it succeeds.
- At finishing the probe of HDA, it decreases the refcount as if it
were already bound at the bus probe, since the component is bound
now. This triggers a kernel WARNING due to the unbalance.
As a workaround, in this patch, we just disable the on-demand i915
component binding in the codec driver. This essentially reverts back
to the state of 4.4 kernel.
We know that this is no real solution, but it's a minimalistic simple
change that can be applied to 4.5.x kernel as stable.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=94566
Reported-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: <stable@vger.kernel.org> # v4.5
Signed-off-by: Takashi Iwai <tiwai@suse.de>
snd_hdac_sync_audio_rate() call is mandatory only for HSW and later
models, but we call the function unconditionally blindly assuming that
the function doesn't do anything harmful. But since recently, the
function checks the validity of the passed pin NID, and eventually
spews the warning if an unexpected pin is passed. This is seen on old
chips like Baytrail.
The fix is to limit the call of this function again only for the chips
with the proper binding. This can be identified by the same flag as
the eld notifier.
Reported-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Tested-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: <stable@vger.kernel.org> # v4.5
Signed-off-by: Takashi Iwai <tiwai@suse.de>
We forgot to copy monitor_present value when updating the ELD
information. This won't change the ELD retrieval and the jack
notification behavior, but appears only in the proc output. In that
sense, it's no fatal error, but a bug is a bug is a bug.
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The commit [b62232d429fa: ALSA: hda - Limit i915 HDMI binding only for
HSW and later] tried to limit the usage of i915 audio notifier to the
recent Intel models and switch to the old method on pre-Haswell
models. However, it assumed that the i915 component binding hasn't
been done on such models, and the assumption was wrong: namely,
Baytrail had already the i915 component binding due to powerwell
control. Thus, the workaround wasn't applied to Baytrail.
For fixing this properly, this patch introduces a new flag indicating
the usage of audio notifier and codec_has_acomp() refers to this flag
instead of checking the existence of audio component.
Reported-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: <stable@vger.kernel.org> # v4.5
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The recent change in HD-audio HDMI/DP codec driver for allowing the
dynamic PCM binding introduced a new spec->pcm_mutex. One of the
protected area by this mutex is hdmi_present_sense(). As reported by
Intel CI tests, unfortunately, the new mutex causes a deadlock when
the hotplug/unplug is triggered during the codec is in runtime
suspend. The buggy code path is like the following:
hdmi_unsol_event() -> ...
-> hdmi_present_sense()
==> ** here taking pcm_mutex
-> hdmi_present_sense_via_verbs()
-> snd_hda_power_up_pm() -> ... (runtime resume calls)
-> generic_hdmi_resume()
-> hdmi_present_sense()
==> ** here taking pcm_mutex again!
As we can see here, the problem is that the mutex is taken before
snd_hda_power_up_pm() call that triggers the runtime resume. That is,
the obvious solution is to move the power up/down call outside the
mutex; it is exactly what this patch provides.
The patch also clarifies why this bug wasn't caught beforehand. We
used to have the i915 audio component for hotplug for all Intel chips,
and in that code path, there is no power up required but the
information is taken directly from the graphics side. However, we
recently switched back to the old method for some old Intel chips due
to regressions, and now the deadlock issue is surfaced.
Fixes: a76056f2e5 ('ALSA: hda - hdmi dynamically bind PCM to pin when monitor hotplug')
Reported-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Tested-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
It turned out that the pre-HSW Intel chips are incompatible with the
naive assumption we had -- the fixed mapping between the port and the
HD-audio widget. This may result in the bad access, as captured by
the recent patch to add a WARN_ON() for the port mapping check.
As a quick workaround, disable the i915 audio component binding for
all pre-Haswell models.
Reported-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: <stable@vger.kernel.org> # v4.5
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Cirrus HD-audio driver may adjust GPIO pins for EAPD dynamically
depending on the jack plug state. This works fine for the auto-mute
mode where the speaker gets muted upon the HP jack plug. OTOH, when
the auto-mute mode is off, this turns off the EAPD unexpectedly
depending on the jack state, which results in the silent speaker
output.
This patch fixes the silent speaker output issue by setting GPIO bits
constantly when the auto-mute mode is off.
Reported-and-tested-by: moosotc@gmail.com
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Vendor ID 0x10de0082 is used by a yet-to-be-named GPU chip.
This chip also has the 2-ch audio swapping bug, so patch_nvhdmi is
appropriate here.
Signed-off-by: Aaron Plattner <aplattner@nvidia.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This Lenovo ThinkCentre AIO also uses Line2 as mic mute button and
uses GPIO2 to control the mic mute led, so applying this quirk can
make both the button and led work.
Cc: stable@vger.kernel.org
BugLink: https://bugs.launchpad.net/bugs/1555912
Signed-off-by: Hui Wang <hui.wang@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The current Intel HDMI codec driver supports only three fixed ports
from port B to port D. However, i915 driver may assign a DP on other
ports, e.g. port A, when no eDP is used. This incompatibility is
caught later at pin_nid_to_pin_index() and results in a warning
message like "HDMI: pin nid 4 not registered" at each time.
This patch filters out such invalid events beforehand, so that the
kernel won't be too grumbling.
Reported-by: Stefan Assmann <sassmann@kpanic.de>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Just like CX20722, CX7024 codec also requires the power down at reboot
in order to reduce the noise at reboot/shutdown.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=113511
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Chmap helper arguments are modified to use either hdac_device
object or hdac_chmap object instead of codec specific object.
With this moving these APIs to core will be easier.
Helper added to access a specific channel_allocation object
instead of directly accessing.
Signed-off-by: Subhransu S. Prusty <subhransu.s.prusty@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Add slot and channel count programming to hdmi_chmap object and
move the chmap_ops to core. Use register_chmap_ops API to
register for default ops. Override specific chmap ops in the
driver.
Signed-off-by: Subhransu S. Prusty <subhransu.s.prusty@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
With this chmap object is added as private data and new ops are
added to access driver specific chmap.
Signed-off-by: Subhransu S. Prusty <subhransu.s.prusty@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
chmap object represents multichannel capability and contains chmap
ops. Legacy driver is updated to use this.
With next set of patches chmap object is moved to common to be
reused by other drivers (ex: skylake ASoC hdmi driver).
Signed-off-by: Subhransu S. Prusty <subhransu.s.prusty@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Defer to register acomp eld notifier until hdmi audio driver
is fully ready.
After registering eld notifier, gfx driver can use this
callback function to notify audio driver the monitor
connection event. However this action may happen when
audio driver is adding the pins or doing other initialization.
This is not always safe, however. For example, using
per_pin->lock before the lock is initialized.
Let's register the eld notifier after the initialization is done.
Signed-off-by: Libin Yang <libin.yang@linux.intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
To make sure audio_ptr is set before intel_audio_codec_enable()
or intel_audio_codec_disable() calling pin_eld_notify(),
this patch adds wmb barrier to prevent optimizing.
Signed-off-by: Libin Yang <libin.yang@linux.intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This patch applies the microphone-related fix created for the Acer
Aspire E1-572 to the E1-472 as well, as it uses the same Realtek ALC282
CODEC and demonstrates the same issues.
This patch allows an external, headset microphone to be used and limits
the gain on the (quite noisy) internal microphone.
Signed-off-by: Simon South <simon@simonsouth.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
hdmi_find_pcm_slot return -EBUSY when not no pcm slot found,
not -ENODEV. So the caller should compare with -EBUSY.
Fixes: a76056f2e5 ('ALSA: hda - hdmi dynamically bind PCM to pin when monitor hotplug')
Signed-off-by: Libin Yang <libin.yang@linux.intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Currently the interrupt handler of HD-audio driver assumes that no irq
update is needed while processing the irq. But in reality, it has
been confirmed that the HW irq is issued even during the irq
handling. Since we clear the irq status at the beginning, process the
interrupt, then exits from the handler, the lately issued interrupt is
left untouched without being properly processed.
This patch changes the interrupt handler code to loop over the
check-and-process. The handler tries repeatedly as long as the IRQ
status are turned on, and either stream or CORB/RIRB is handled.
For checking the stream handling, snd_hdac_bus_handle_stream_irq()
returns a value indicating the stream indices bits. Other than that,
the change is only in the irq handler itself.
Reported-by: Libin Yang <libin.yang@linux.intel.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
HP EliteBook 755 G2 with ALC3228 (ALC280) codec [103c:221c] requires
the known fixup (ALC269_FIXUP_HEADSET_MIC) for making the headset mic
working. Also, it suffers from the loopback noise problem, so we
should disable aamix path as well.
Reported-by: Derick Eddington <derick.eddington@gmail.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
On one of the machines we enable, we found that the actual speaker volume
did not always correspond to the volume set in alsamixer. This patch
fixes that problem.
This patch was orginally written by Kailang @ Realtek, I've rebased it
to fit sound git master.
Cc: stable@vger.kernel.org
BugLink: https://bugs.launchpad.net/bugs/1549660
Co-Authored-By: Kailang <kailang@realtek.com>
Signed-off-by: David Henningsson <david.henningsson@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
After login to the desktop on Dell Inspiron 3162,
there's a very loud background noise comes from the builtin speaker.
The noise does not go away even if the speaker is muted.
The noise disappears after using the aamix fixup.
Codec: Realtek ALC3234
Address: 0
AFG Function Id: 0x1 (unsol 1)
Vendor Id: 0x10ec0255
Subsystem Id: 0x10280725
Revision Id: 0x100002
No Modem Function Group found
BugLink: http://bugs.launchpad.net/bugs/1549620
Signed-off-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
eld control is created based on pcm now.
When monitor is connected, eld control will be bound to
pin automatically.
Signed-off-by: Libin Yang <libin.yang@linux.intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Since the recent integration of kctl jack and input jack layers, we
can basically build the jack layer even without input devices. That
is, the jack layer itself can be built with conditional to enable the
input device support or not, while the users may enable always
CONFIG_SND_JACK unconditionally.
For achieving it, this patch changes the following:
- A new Kconfig, CONFIG_SND_JACK_INPUT_DEV, was introduced to indicate
whether the jack layer supports the input device,
- A few items in snd_jack struct and relevant codes are conditionally
built upon CONFIG_SND_JACK_INPUT_DEV,
- The users of CONFIG_SND_JACK drop the messy dependency on
CONFIG_INPUT.
This change also automagically fixes a potential bug in HD-audio
driver Arnd reported, where the NULL or uninitialized jack instance is
dereferenced.
Reported-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Some Skylake machines show the codec probe errors in certain
situations, e.g. HP Z240 desktop fails to probe the onboard Realtek
codec at reloading the snd-hda-intel module like:
snd_hda_intel 0000:00:1f.3: spurious response 0x200:0x2, last cmd=0x000000
snd_hda_intel 0000:00:1f.3: azx_get_response timeout, switching to polling mode: lastcmd=0x000f0000
snd_hda_intel 0000:00:1f.3: No response from codec, disabling MSI: last cmd=0x000f0000
snd_hda_intel 0000:00:1f.3: Codec #0 probe error; disabling it...
hdaudio hdaudioC0D2: no AFG or MFG node found
snd_hda_intel 0000:00:1f.3: no codecs initialized
Also, HP G470 G3 suffers from the similar problem, as reported in
bugzilla below. On this machine, the codec probe error appears even
at a fresh boot.
As Libin suggested, the same workaround used for Broxton in the commit
[6639484ddaf6: ALSA: hda - disable dynamic clock gating on Broxton
before reset] can be applied for Skylake in order to fix this problem.
The Intel HW team also confirmed that this is needed for SKL.
This patch makes the workaround applied to both SKL and BXT
platforms. The referred macros are moved and one superfluous macro
(IS_BROXTON()) is another one (IS_BXT()) as well.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=112731
Suggested-by: Libin Yang <libin.yang@linux.intel.com>
Cc: <stable@vger.kernel.org> # v4.4+
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Use shiny new acpi_dev_present() and remove all the boilerplate
to search for a particular ACPI device. No functional change.
Cf. 2d12b6b381 ("ACPI / utils: Add acpi_dev_present()").
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Acked-by: Hui Wang <hui.wang@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
On Intel platform, if !dyn_pcm_assign, spec->pcm_rec[].jack is not
NULL even after snd_hda_jack_tbl_clear() is called to free snd_jack.
This may cause access invalid memory when calling snd_jack_report.
Fixes: 25e4abb33d ('ALSA: hda - hdmi jack created based on pcm')
Signed-off-by: Libin Yang <libin.yang@linux.intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Lu, Han