Add a comment above NAND_MFR_TOSHIBA and SPINAND_MFR_TOSHIBA definitions
that Toshiba and Kioxia ID are the same.
Since its independence from Toshiba Group, Toshiba memory Co has become
Kioxia Co.
Signed-off-by: Yoshio Furuyama <ytc-mb-yfuruyama7@kioxia.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/1581051561-7302-1-git-send-email-ytc-mb-yfuruyama7@kioxia.com
If the write protect signal from this IP is connected to the NAND
device, this IP can handle the WP# pin via the WRITE_PROTECT
register.
The Denali NAND Flash Memory Controller User's Guide describes
this register like follows:
When the controller is in reset, the WP# pin is always asserted
to the device. Once the reset is removed, the WP# is de-asserted.
The software will then have to come and program this bit to
assert/de-assert the same.
1 - Write protect de-assert
0 - Write protect assert
The default value is 1, so the write protect is de-asserted after
the reset is removed. The driver can write to the device unless
someone has explicitly cleared register before booting the kernel.
The boot ROM of some UniPhier SoCs (LD4, Pro4, sLD8, Pro5) is the
case; the boot ROM clears the WRITE_PROTECT register when the system
is booting from the NAND device, so the NAND device becomes read-only.
Set it to 1 in the driver in order to allow the write access to the
device.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20200127123934.11847-1-yamada.masahiro@socionext.com
The used way to compute jiffies timeout brokes when
jiffie difference is 1.
Assume that nand_soft_waitrdy is called with timeout_ms==1.
Jiffies are 1000 for example (assume something more like 1000.99
- just before incrementing to 1001).
We compute timeout_ms = 1000+msecs_to_jiffies(1) = 1001.
nand_read_data_op is called for the first time and returns 0.
During the call jiffies changes to 1001 thus "while loop" ends
here (wrongly). Notice that routine was called with expected timeout
1ms but actual timeout used was something between 0...1ms.
Fixes STM32MP1 FMC2 NAND controller which sometimes failed
exactly in this way.
Signed-off-by: Martin Devera <devik@eaxlabs.cz>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20200116135431.17480-1-devik@eaxlabs.cz
The Hyperbus core expects that HyperFlash is always directly mapped for
both read and write, but in reality this may not always be the case, e.g.
Renesas RPC-IF has read only direct mapping. Move the code setting up the
direct mapping from the Hyperbus core to thh TI AM554 HBMC driver.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
In case the compatible "cypress,hyperflash" is not given
output a proper error message.
Signed-off-by: Dirk Behme <dirk.behme@de.bosch.com>
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
- Don't use `tmp` for two purposes (return value, loop counter).
Instead, use `i` for the loop counter, and `ret` for the return value.
- Don't use tabs between type and name in variable declarations,
for consistency with other functions in spi-nor.c.
- Rewrite nested `if`s as `if (a && b)`.
- Remove `info` variable, and use spi_nor_ids[i] directly.
Signed-off-by: Jonathan Neuschäfer <j.neuschaefer@gmx.net>
[tudor.ambarus@microchip.com: change i's type from int to unsigned int,
reorder local variables]
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Make use of the spi-mem direct mapping API to let advanced controllers
optimize read/write operations when they support direct mapping.
Based on the original patch by Boris Brezillon
<boris.brezillon@bootlin.com>.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Reviewed-by: Boris Brezillon <boris.brezillon@collabora.com>
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
spi_nor_spimem_xfer_data() being a helper function for the data reads/
writes contains 3 fragments that depend on the data direction; and I'm
going to add another one to call the SPI dirmap API...
I think this function should be split so that the common fragments are
put into 2 functions, spi_nor_spimem_bounce() and spi_nor_spimem_exec_op()
called from spi_nor_spimem_{read|write}_data(), and the data direction
dependent bits moved back into those read/write functions -- that way we
would be able to avoid *goto*s otherwise needed in the next patch adding
the SPI dirmap support...
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
The shift variable of SR_BP is conclusive because the first bit of SR_BP
is fixed on all known flashes. Replace ffs operation with SR_BP_SHIFT.
Signed-off-by: Jungseung Lee <js07.lee@samsung.com>
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
The driver calls le32_to_cpu() to convert the little-endian tables
to a CPU endianness, where le32_to_cpus() should have been called.
Was going to use that one... and then discovered a whole array
converter, le32_to_cpu_array()! :-)
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
* block2mtd: page index should use pgoff_t
* maps: physmap: minimal Runtime PM support
* maps: pcmciamtd: avoid possible sleep-in-atomic-context bugs
* concat: Fix a comment referring to an unknown symbol
Raw NAND
* Macronix: Use match_string() helper
* Atmel: switch to using devm_fwnode_gpiod_get()
* Denali: rework the SKIP_BYTES feature and add reset controlling
* Brcmnand: set appropriate DMA mask
* Cadence: add unspecified HAS_IOMEM dependency
* Various cleanup.
Onenand
* Rename Samsung and Omap2 drivers to avoid possible build warnings
* Enable compile testing
* Various build issues
* Kconfig cleanup
SPI-NAND
* Support for Toshiba TC58CVG2S0HRAIJ
SPI-NOR:
- Add support for TB selection using SR bit 6,
- Add support for few flashes.
-----BEGIN PGP SIGNATURE-----
iQEzBAABCgAdFiEE9HuaYnbmDhq/XIDIJWrqGEe9VoQFAl4zMfgACgkQJWrqGEe9
VoS0xwf+KdaihRno4SkDovcHoF7K54N6CqBhwuV9uabfy4phEr38cyvaivYu0rG7
k/n3CUNRDghTh7DAUT7pBsjUeZn9XxvKyQaZz34TBgoQYwGz57ssp8lMRmJkYoA6
t9z95N9bRJ+IzZJlYELCbhNq+aOGyWYgWL+aaO0CE8OyOeWzdZumdd4k7cF7rSAu
9gWV/6iX/qP081NexfjPEVmMtNQ+0p4T7zQ01nQA7rIZiVoIgMKwBu41aRYycEEs
LeuV5gNEDn2vGBl+u85w5oF6o1TIzDeTmh0G7Jm3NQGGco2kOOZ1O39a0hrDONrA
hEoEIG/rAMKOtaLr6rCGnV/5/i/Tlw==
=WC+m
-----END PGP SIGNATURE-----
Merge tag 'mtd/for-5.6' of git://git.kernel.org/pub/scm/linux/kernel/git/mtd/linux
Pull MTD updates from Miquel Raynal:
"MTD core
- block2mtd: page index should use pgoff_t
- maps: physmap: minimal Runtime PM support
- maps: pcmciamtd: avoid possible sleep-in-atomic-context bugs
- concat: Fix a comment referring to an unknown symbol
Raw NAND:
- Macronix: Use match_string() helper
- Atmel: switch to using devm_fwnode_gpiod_get()
- Denali: rework the SKIP_BYTES feature and add reset controlling
- Brcmnand: set appropriate DMA mask
- Cadence: add unspecified HAS_IOMEM dependency
- Various cleanup.
Onenand:
- Rename Samsung and Omap2 drivers to avoid possible build warnings
- Enable compile testing
- Various build issues
- Kconfig cleanup
SPI-NAND:
- Support for Toshiba TC58CVG2S0HRAIJ
SPI-NOR:
- Add support for TB selection using SR bit 6,
- Add support for few flashes"
* tag 'mtd/for-5.6' of git://git.kernel.org/pub/scm/linux/kernel/git/mtd/linux: (41 commits)
mtd: concat: Fix a comment referring to an unknown symbol
mtd: rawnand: add unspecified HAS_IOMEM dependency
mtd: block2mtd: page index should use pgoff_t
mtd: maps: physmap: Add minimal Runtime PM support
mtd: maps: pcmciamtd: fix possible sleep-in-atomic-context bugs in pcmciamtd_set_vpp()
mtd: onenand: Rename omap2 driver to avoid a build warning
mtd: onenand: Use a better name for samsung driver
mtd: rawnand: atmel: switch to using devm_fwnode_gpiod_get()
mtd: spinand: add support for Toshiba TC58CVG2S0HRAIJ
mtd: rawnand: macronix: Use match_string() helper to simplify the code
mtd: sharpslpart: Fix unsigned comparison to zero
mtd: onenand: Enable compile testing of OMAP and Samsung drivers
mtd: onenand: samsung: Fix printing format for size_t on 64-bit
mtd: onenand: samsung: Fix pointer cast -Wpointer-to-int-cast warnings on 64 bit
mtd: rawnand: denali: remove hard-coded DENALI_DEFAULT_OOB_SKIP_BYTES
mtd: rawnand: denali_dt: add reset controlling
dt-bindings: mtd: denali_dt: document reset property
mtd: rawnand: denali_dt: Add support for configuring SPARE_AREA_SKIP_BYTES
mtd: rawnand: denali_dt: error out if platform has no associated data
mtd: rawnand: brcmnand: Set appropriate DMA mask
...
UBI:
- Fixes for memory leaks in error paths
- Fix for an logic error in a fastmap selfcheck
UBIFS:
- Fix for FS_IOC_SETFLAGS related to fscrypt flag
- Support for FS_ENCRYPT_FL
- Fix for a dead lock in bulk-read mode
-----BEGIN PGP SIGNATURE-----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=9tMk
-----END PGP SIGNATURE-----
Merge tag 'upstream-5.6-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rw/ubifs
Pull UBI/UBIFS updates from Miquel Raynal:
"This pull request contains mostly fixes for UBI and UBIFS:
UBI:
- Fixes for memory leaks in error paths
- Fix for an logic error in a fastmap selfcheck
UBIFS:
- Fix for FS_IOC_SETFLAGS related to fscrypt flag
- Support for FS_ENCRYPT_FL
- Fix for a dead lock in bulk-read mode"
Sent on behalf of Richard Weinberger who is traveling.
* tag 'upstream-5.6-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rw/ubifs:
ubi: Fix an error pointer dereference in error handling code
ubifs: Fix memory leak from c->sup_node
ubifs: Fix ino_t format warnings in orphan_delete()
ubifs: Fix deadlock in concurrent bulk-read and writepage
ubifs: Fix wrong memory allocation
ubi: Free the normal volumes in error paths of ubi_attach_mtd_dev()
ubi: Check the presence of volume before call ubi_fastmap_destroy_checkmap()
ubifs: Add support for FS_ENCRYPT_FL
ubifs: Fix FS_IOC_SETFLAGS unexpectedly clearing encrypt flag
ubi: wl: Remove set but not used variable 'prev_e'
ubi: fastmap: Fix inverted logic in seen selfcheck
- remove ioremap_nocache given that is is equivalent to
ioremap everywhere
-----BEGIN PGP SIGNATURE-----
iQI/BAABCgApFiEEgdbnc3r/njty3Iq9D55TZVIEUYMFAl4vKHwLHGhjaEBsc3Qu
ZGUACgkQD55TZVIEUYMPGBAAuVNUZaZfWYHpiVP2oRcUQUguFiD3NTbknsyzV2oH
J9P0GfeENSKwE9OOhZ7XIjnCZAJwQgTK/ppQY5yiQ/KAtYyyXjXEJ6jqqjiTDInr
+3+I3t/LhkgrK7tMrb7ylTGa/d7KhaciljnOXC8+b75iddvM9I1z2pbHDbppZMS9
wT4RXL/cFtRb85AfOyPLybcka3f5P2gGvQz38qyimhJYEzHDXZu9VO1Bd20f8+Xf
eLBKX0o6yWMhcaPLma8tm0M0zaXHEfLHUKLSOkiOk+eHTWBZ3b/w5nsOQZYZ7uQp
25yaClbameAn7k5dHajduLGEJv//ZjLRWcN3HJWJ5vzO111aHhswpE7JgTZJSVWI
ggCVkytD3ESXapvswmACSeCIDMmiJMzvn6JvwuSMVB7a6e5mcqTuGo/FN+DrBF/R
IP+/gY/T7zIIOaljhQVkiEIIwiD/akYo0V9fheHTBnqcKEDTHV4WjKbeF6aCwcO+
b8inHyXZSKSMG//UlDuN84/KH/o1l62oKaB1uDIYrrL8JVyjAxctWt3GOt5KgSFq
wVz1lMw4kIvWtC/Sy2H4oB+RtODLp6yJDqmvmPkeJwKDUcd/1JKf0KsZ8j3FpGei
/rEkBEss0KBKyFAgBSRO2jIpdj2epgcBcsdB/r5mlhcn8L77AS6mHbA173kY4pQ/
Kdg=
=TUCJ
-----END PGP SIGNATURE-----
Merge tag 'ioremap-5.6' of git://git.infradead.org/users/hch/ioremap
Pull ioremap updates from Christoph Hellwig:
"Remove the ioremap_nocache API (plus wrappers) that are always
identical to ioremap"
* tag 'ioremap-5.6' of git://git.infradead.org/users/hch/ioremap:
remove ioremap_nocache and devm_ioremap_nocache
MIPS: define ioremap_nocache to ioremap
* Macronix: Use match_string() helper
* Atmel: switch to using devm_fwnode_gpiod_get()
* Denali: rework the SKIP_BYTES feature and add reset controlling
* Brcmnand: set appropriate DMA mask
* Various cleanup.
Onenand drivers
* Rename Samsung and Omap2 drivers to avoid possible build warnings
* Enable compile testing
* Various build issues
* Kconfig cleanup
SPI-NAND
* Support for Toshiba TC58CVG2S0HRAIJ
-----BEGIN PGP SIGNATURE-----
iQEzBAABCgAdFiEE9HuaYnbmDhq/XIDIJWrqGEe9VoQFAl4nSy0ACgkQJWrqGEe9
VoSr1gf+KKMtE8GabWYbKsgKRx1cmC/0pvRmp7wqjul4gd/s+llKzEDG/qMYUOua
PgynNJeP7LPIZJWqo8TjXZcNxs1E0JSoAjYK58Hm9MOIwiwmdSE7GOVxv8/1drN/
7mjJvnGznol/2GD3U4NRvW/SZHkj0/Xt9Ys70qdpcWDQWJSIUIhrNuKOMgjTP+kp
XfZ4vWL6T9LHJiIojLTkrfjXH774dWflSj8bySz+9d9kwkbvKEGU6zb6sKfGO4nm
yYqQhpUrbN8c4t+hSuJlf140haVhwCIQeujUNlTn2oDXnJIO/98k0jDSn6dpUSdx
H6NvWMa8e8Bz7HAbB7/VOawtjt/k+w==
=UPI6
-----END PGP SIGNATURE-----
Merge tag 'nand/for-5.6' into mtd/next
Raw NAND
* Macronix: Use match_string() helper
* Atmel: switch to using devm_fwnode_gpiod_get()
* Denali: rework the SKIP_BYTES feature and add reset controlling
* Brcmnand: set appropriate DMA mask
* Various cleanup.
Onenand drivers
* Rename Samsung and Omap2 drivers to avoid possible build warnings
* Enable compile testing
* Various build issues
* Kconfig cleanup
SPI-NAND
* Support for Toshiba TC58CVG2S0HRAIJ
- Add support for TB selection using SR bit 6,
- Add support for few flashes.
-----BEGIN PGP SIGNATURE-----
iQEzBAABCAAdFiEEHUIqys8OyG1eHf7fS1VPR6WNFOkFAl4l5iYACgkQS1VPR6WN
FOksswf/Tq2UoKBdPuseIUFuzra98K78ItVAAGPnMM2rMnG9bi0SLsKDdYIt/E2s
MHfcZdk9FA+DqCyfXk7FJDSFjvT5L92xg+lJSQul7GL/OOUWUlYJVuPpxCUFzJmW
w/u9qFdbsughBFqMKgCPA11+wDPBbBfOjI/PzfKpjuFr4d4rOevX9bnojAa/8pR2
FDJ/kfjDByxa60uAZbAMh0tV8wHgVtnLUNDwrh+49BLHN4a0vIq3PP/YiQLvo2VY
IE1x6Va696onBkcXNtWOYFiS183Dc0mIVRYwAPDvpF6MWcWbZXQ2XrnRb4B8snMY
mLBWqGpQ4b88Nd1npTWxIUIUJPXgqQ==
=3kW5
-----END PGP SIGNATURE-----
Merge tag 'spi-nor/for-5.6' into mtd/next
SPI NOR core changes:
- Add support for TB selection using SR bit 6,
- Add support for few flashes.
Fix the comment describing what the mtd_concat_destroy() function
does. It referrers to the concat_mtd_devs symbol which has never
existed (at least not since the beginning of the Git era).
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Currently CONFIG_MTD_NAND_CADENCE implicitly depends on
CONFIG_HAS_IOMEM=y; consequently, on architectures without IOMEM we get
the following build error:
ld: drivers/mtd/nand/raw/cadence-nand-controller.o: in function `cadence_nand_dt_probe.cold.31':
drivers/mtd/nand/raw/cadence-nand-controller.c:2969: undefined reference to `devm_platform_ioremap_resource'
ld: drivers/mtd/nand/raw/cadence-nand-controller.c:2977: undefined reference to `devm_ioremap_resource'
Fix the build error by adding the unspecified dependency.
Reported-by: Brendan Higgins <brendanhiggins@google.com>
Signed-off-by: Brendan Higgins <brendanhiggins@google.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Page index use pgoff_t to prevent risk of truncation.
Signed-off-by: Liu Song <liu.song11@zte.com.cn>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Add minimal runtime PM support (enable on probe, disable on remove), to
ensure proper operation with a parent device that uses runtime PM.
This is needed on systems where the FLASH is connected to a bus
controller that is contained in a PM domain and/or has a gateable
functional clock. In such cases, before accessing any device connected
to the external bus, the PM domain must be powered up, and/or the
functional clock must be enabled, which is typically handled through
runtime PM by the bus controller driver.
An example of this is the Renesas APE6-EVM development board, which has
an Ethernet controller and a CFI FLASH connected to the Bus State
Controller (BSC) of an R-Mobile APE6 SoC.
As long as the Ethernet driver, which had Runtime PM support since
commit 3a611e26e9 ("net/smsc911x: Add minimal runtime PM
support"), keeps the BSC powered, accessing the FLASH works.
When the ethernet node in r8a73a4-ape6evm.dts is disabled, the BSC is
never powered up, and the kernel crashes when trying to access the
FLASH:
Unhandled fault: imprecise external abort (0x1406) at 0x00000000
pgd = (ptrval)
[00000000] *pgd=7fef2835
Internal error: : 1406 [#1] SMP ARM
CPU: 0 PID: 122 Comm: hd Tainted: G W 5.5.0-rc1-ape6evm-00814-g38ca966db25b9dbd-dirty #136
Hardware name: Generic R8A73A4 (Flattened Device Tree)
PC is at chip_ready+0x12c/0x380
LR is at chip_ready+0x10c/0x380
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
The driver may sleep while holding a spinlock.
The function call path (from bottom to top) in Linux 4.19 is:
drivers/pcmcia/pcmcia_resource.c, 312:
mutex_lock in pcmcia_fixup_vpp
drivers/mtd/maps/pcmciamtd.c, 309:
pcmcia_fixup_vpp in pcmciamtd_set_vpp
drivers/mtd/maps/pcmciamtd.c, 306:
_raw_spin_lock_irqsave in pcmciamtd_set_vpp
drivers/pcmcia/pcmcia_resource.c, 312:
mutex_lock in pcmcia_fixup_vpp
drivers/mtd/maps/pcmciamtd.c, 312:
pcmcia_fixup_vpp in pcmciamtd_set_vpp
drivers/mtd/maps/pcmciamtd.c, 306:
_raw_spin_lock_irqsave in pcmciamtd_set_vp
mutex_lock() may sleep at runtime.
To fix these bugs, the spinlock is replaced with a mutex.
These bugs are found by a static analysis tool STCheck written by
myself.
Signed-off-by: Jia-Ju Bai <baijiaju1990@gmail.com>
Reviewed-by: Dominik Brodowski <linux@dominikbrodowski.net>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
As previously reported by Sudip Mukherjee for the Samsung driver, the
omap2 onenand driver is called omap2.c in our directory and omap2.c in
the tty/serial/ directory. If both drivers are compiled as modules, it
would produce the following warning:
warning: same module names found:
drivers/tty/serial/omap2.ko
drivers/mtd/nand/onenand/omap2.ko
Rename the onenand omap2 driver so that it fits the folder's
convention: onenand_omap2.c.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Commit 55ed51fff2 ("{tty: serial, nand: onenand}: samsung: rename to
fix build warning") has changed the samsung.c driver to be
samsung_mtd.c in order to avoid a conflict in module names with the
tty driver.
Since the *_mtd suffix is very undescriptive, rename it to
onenand_samsung.c, following the folder's convention. Same will be
applied to the omap2 onenand driver.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
devm_fwnode_get_index_gpiod_from_child() is going away as the name is
too unwieldy, let's switch to using the new devm_fwnode_gpiod_get().
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Toshiba recently launched new revisions of their serial SLC NAND series.
TC58CVG2S0HRAIJ is a refresh of previous series with minor improvements.
Basic parameters are same so lets add support for this new revision.
Datasheet: https://business.kioxia.com/info/docget.jsp?did=58601&prodName=TC58CVG2S0HRAIJ
Tested under kernel 5.4.7.
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
Cc: Luka Perkov <luka.perkov@sartura.hr>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
match_string() returns the array index of a matching string.
Use it instead of the open-coded implementation.
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
The unsigned variable log_num is being assigned a return value
from the call to sharpsl_nand_get_logical_num that can return
-EINVAL.
Detected using Coccinelle:
./drivers/mtd/parsers/sharpslpart.c:207:6-13: WARNING: Unsigned expression compared with zero: log_num > 0
Fixes: 8a4580e4d2 ("mtd: sharpslpart: Add sharpslpart partition parser")
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
OMAP and Samsung OneNAND drivers can be compile tested. The OMAP
drivers still depends on mach header so limit the compile testing to
ARMv7.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Reported-by: kbuild test robot <lkp@intel.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Print size_t as %zu to fix -Wformat warnings when compiling on 64-bit
platform (e.g. with COMPILE_TEST):
drivers/mtd/nand/onenand/samsung_mtd.c: In function ‘s5pc110_read_bufferram’:
drivers/mtd/nand/onenand/samsung_mtd.c:661:16: warning:
format ‘%d’ expects argument of type ‘int’, but argument 3 has type ‘size_t {aka long unsigned int}’ [-Wformat=]
dev_err(dev, "Couldn't map a %d byte buffer for DMA\n", count);
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
iomem pointers should be casted to unsigned long to avoid
-Wpointer-to-int-cast warnings when compiling on 64-bit platform (e.g.
with COMPILE_TEST):
drivers/mtd/nand/onenand/samsung_mtd.c: In function ‘s3c_onenand_readw’:
drivers/mtd/nand/onenand/samsung_mtd.c:251:6: warning:
cast from pointer to integer of different size [-Wpointer-to-int-cast]
if ((unsigned int) addr < ONENAND_DATARAM && onenand->bootram_command) {
^
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
As commit 0d55c668b2 (mtd: rawnand: denali: set SPARE_AREA_SKIP_BYTES
register to 8 if unset") says, there were three solutions discussed:
[1] Add a DT property to specify the skipped bytes in OOB
[2] Associate the preferred value with compatible
[3] Hard-code the default value in the driver
At that time, [3] was chosen because I did not have enough information
about the other platforms than UniPhier.
That commit also says "The preferred value may vary by platform. If so,
please trade up to a different solution." My intention was to replace
[3] with [2], not keep both [2] and [3].
Now that we have switched to [2] for SOCFPGA's SPARE_AREA_SKIP_BYTES=2,
[3] should be removed. This should be OK because denali_pci.c just
gets back to the original behavior.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
According to the Denali NAND Flash Memory Controller User's Guide,
this IP has two reset signals.
rst_n: reset most of FFs in the controller core
reg_rst_n: reset all FFs in the register interface, and in the
initialization sequencer
This commit supports controlling those reset signals.
It is possible to control them separately from the IP point of view
although they might be often tied up together in actual SoC integration.
The IP spec says, asserting only the reg_rst_n without asserting rst_n
will cause unpredictable behavior in the controller. So, the driver
deasserts ->rst_reg and ->rst in this order.
Another thing that should be kept in mind is the automated initialization
sequence (a.k.a. 'bootstrap' process) is kicked off when reg_rst_n is
deasserted.
When the reset is deasserted, the controller issues a RESET command
to the chip select 0, and attempts to read out the chip ID, and further
more, ONFI parameters if it is an ONFI-compliant device. Then, the
controller sets up the relevant registers based on the detected
device parameters.
This process might be useful for tiny boot firmware, but is redundant
for Linux Kernel because nand_scan_ident() probes devices and sets up
parameters accordingly. Rather, this hardware feature is annoying
because it ends up with misdetection due to bugs.
So, commit 0615e7ad5d ("mtd: nand: denali: remove Toshiba and Hynix
specific fixup code") changed the driver to not rely on it.
However, there is no way to prevent it from running. The IP provides
the 'bootstrap_inhibit_init' port to suppress this sequence, but it is
usually out of software control, and dependent on SoC implementation.
As for the Socionext UniPhier platform, LD4 always enables it. For the
later SoCs, the bootstrap sequence runs depending on the boot mode.
I added usleep_range() to make the driver wait until the sequence
finishes. Otherwise, the driver would fail to detect the chip due
to the race between the driver and hardware-controlled sequence.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
The SPARE_AREA_SKIP_BYTES register is reset when the controller reset
signal is toggled. Yet, this register must be configured to match the
content of the NAND OOB area. The current default value is always set
to 8 and is programmed into the hardware in case the hardware was not
programmed before (e.g. in a bootloader) with a different value. This
however does not work when the block is reset properly by Linux.
On Altera SoCFPGA CycloneV, ArriaV and Arria10, which are the SoCFPGA
platforms which support booting from NAND, the SPARE_AREA_SKIP_BYTES
value must be set to 2. On Socionext Uniphier, the value is 8. This
patch adds support for preconfiguring the default value and handles
the special SoCFPGA case by setting the default to 2 on all SoCFPGA
platforms, while retaining the original behavior and default value of
8 on all the other platforms.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Miquel Raynal <miquel.raynal@bootlin.com>
Cc: Richard Weinberger <richard@nod.at>
Cc: Vignesh Raghavendra <vigneshr@ti.com>
To: linux-mtd@lists.infradead.org
Reviewed-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Acked-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
denali->ecc_caps is a mandatory parameter. If it were left unset,
nand_ecc_choose_conf() would end up with NULL pointer access.
So, every compatible must be associated with proper denali_dt_data.
If of_device_get_match_data() returns NULL, let it fail immediately.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
NAND controllers >= 7.0 with FLASH_DMA support physical addresses up to
40-bit, set an appropriate DMA mask for that purpose.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Clang warns:
../drivers/mtd/nand/onenand/onenand_base.c:1269:3: warning: misleading
indentation; statement is not part of the previous 'if'
[-Wmisleading-indentation]
while (!ret) {
^
../drivers/mtd/nand/onenand/onenand_base.c:1266:2: note: previous
statement is here
if (column + thislen > writesize)
^
1 warning generated.
This warning occurs because there is a space before the tab of the while
loop. There are spaces at the beginning of a lot of the lines in this
block, remove them so that the indentation is consistent with the Linux
kernel coding style and clang no longer warns.
Fixes: a8de85d557 ("[MTD] OneNAND: Implement read-while-load")
Link: https://github.com/ClangBuiltLinux/linux/issues/794
Signed-off-by: Nathan Chancellor <natechancellor@gmail.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Fixes gcc '-Wunused-but-set-variable' warning:
drivers/mtd/nand/onenand/samsung_mtd.c: In function s3c_onenand_check_lock_status:
drivers/mtd/nand/onenand/samsung_mtd.c:731:6: warning: variable tmp set but not used [-Wunused-but-set-variable]
Signed-off-by: Chen Wandun <chenwandun@huawei.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Adjust indentation from spaces to tab (+optional two spaces) as in
coding style with command like:
$ sed -e 's/^ /\t/' -i */Kconfig
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
If "seen_pebs = init_seen(ubi);" fails then "seen_pebs" is an error pointer
and we try to kfree() it which results in an Oops.
This patch re-arranges the error handling so now it only frees things
which have been allocated successfully.
Fixes: daef3dd1f0 ("UBI: Fastmap: Add self check to detect absent PEBs")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Richard Weinberger <richard@nod.at>
This was tested in single, dual and quad mode on a custom board with the
NXP FlexSPI controller.
Signed-off-by: Michael Walle <michael@walle.cc>
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Add support for the Winbond W25Q32JW-xM flashes. These have a
programmable QE bit. There is also the W25Q32JW-xQ variant which shares
the ID with the W25Q32DW and W25Q32FW parts. The W25Q32JW-xQ has the QE
bit hard strapped to 1, thus don't support the /HOLD and /WP pins.
This was tested in single, dual and quad mode on a custom board with the
NXP FlexSPI controller. Also the BP bits as well as the TB bit were
tested.
Signed-off-by: Michael Walle <michael@walle.cc>
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
As we reset the GPMI block at resume, the timing parameters setup by a
previous exec_op is lost. Rewriting GPMI timing registers on first exec_op
after resume fixes the problem.
Fixes: ef347c0cfd ("mtd: rawnand: gpmi: Implement exec_op")
Cc: stable@vger.kernel.org
Signed-off-by: Esben Haabendal <esben@geanix.com>
Acked-by: Han Xu <han.xu@nxp.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
The commit 7b678c69c0 ("mtd: spi-nor: Merge spansion Quad Enable
methods") forgot to actually set the QE bit in some cases. Thus this
breaks quad mode accesses to flashes which support readback of the
status register-2. Fix it.
Fixes: 7b678c69c0 ("mtd: spi-nor: Merge spansion Quad Enable methods")
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
mtd->size is still unassigned when running spansion_post_sfdp_fixups()
hook, therefore use nor->params.size to determine the size of flash device.
This makes sure that 4-byte addressing opcodes are used on Spansion
flashes that are larger than 16MiB and don't have SFDP 4BAIT table
populated.
Fixes: 92094ebc38 ("mtd: spi-nor: Add spansion_post_sfdp_fixups()")
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Reviewed-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
The allocated normal volumes saved in ubi->volumes are not freed
in the error paths in ubi_attach_mtd_dev() and its callees (e.g.
ubi_attach() and ubi_read_volume_table()).
These normal volumes should be freed through kill_volumes() and
vol_release(), but ubi_attach_mtd_dev() may fail before
calling uif_init(), and there will be memory leaks.
So adding a new helper ubi_free_all_volumes() to free the normal
and the internal volumes. And in order to prevent double-free
of volume, reset ubi->volumes[i] to NULL after freeing.
Signed-off-by: Hou Tao <houtao1@huawei.com>
Signed-off-by: Richard Weinberger <richard@nod.at>
Else there may be oops when fastmap is enabled and init_volumes() fails.
Signed-off-by: Hou Tao <houtao1@huawei.com>
Signed-off-by: Richard Weinberger <richard@nod.at>
Fixes gcc '-Wunused-but-set-variable' warning:
drivers/mtd/ubi/wl.c: In function 'find_wl_entry':
drivers/mtd/ubi/wl.c:322:27: warning:
variable 'prev_e' set but not used [-Wunused-but-set-variable]
It's not used any more now, so remove it.
Fixes: f9c34bb529 ("ubi: Fix producing anchor PEBs")
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Richard Weinberger <richard@nod.at>
set_seen() sets the bit corresponding to the PEB number in the bitmap,
so when self_check_seen() wants to find PEBs that haven't been seen we
have to print the PEBs that have their bit cleared, not the ones which
have it set.
Fixes: 5d71afb008 ("ubi: Use bitmaps in Fastmap self-check code")
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Richard Weinberger <richard@nod.at>
The ops aren't used in any SPI NOR controller. Therefore, remove them
altogether.
Signed-off-by: Michael Walle <michael@walle.cc>
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Intel Comet Lake-V has the same SPI serial flash controller as Kaby
Lake. Add Comet Lake-V PCI ID to the driver list of supported devices.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
The driver is for the HiSilicon FMC (Flash Memory Controller), which
supports SPI NOR in addition other memory technologies, like SPI NAND.
Indeed, the naming in the driver is a little inappropriate, especially
considering that there is already another HiSilicon SPI NOR flash
controller (which I believe the FMC is derived from).
Since we now want to provide software support for this other HiSilicon
controller, update code comments to at least try to make it clear that
this driver is for the FMC.
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Adds support for sst26vf016b, a smaller variant of the sst26vf064b.
Tested on a sama5d3 SOC using the atmel,at91rm9200-spi controller.
The dual read could not be tested.
SPI_NOR_QUAD_READ is not added because it requires that the IOC bit
from the Configuration Register to be set to 1, which is not the case:
its default value at power-up is zero and we don't set it to one in
spi-nor either.
Signed-off-by: Joseph Kust <joseph.kust@rockwellcollins.com>
Signed-off-by: Brandon Maier <brandon.maier@rockwellcollins.com>
[tudor.ambarus@microchip.com: Drop quad read flag, amend commit description]
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Micron flashes do not support 16 bit writes on the Status Register.
According to micron datasheets, when using the Write Status Register
(01h) command, the chip select should be driven LOW and held LOW until
the eighth bit of the last data byte has been latched in, after which
it must be driven HIGH. If CS is not driven HIGH, the command is not
executed, flag status register error bits are not set, and the write enable
latch remains set to 1. This fixes the lock operations on micron flashes.
Reported-by: John Garry <john.garry@huawei.com>
Fixes: 39d1e3340c ("mtd: spi-nor: Fix clearing of QE bit on lock()/unlock()")
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Tested-by: John Garry <john.garry@huawei.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
With gcc -O3, we get a new warning:
In file included from arch/arm64/include/asm/processor.h:28,
from drivers/mtd/sm_ftl.c:8:
In function 'memset',
inlined from 'sm_read_sector.constprop' at drivers/mtd/sm_ftl.c:250:3:
include/linux/string.h:411:9: error: argument 1 null where non-null expected [-Werror=nonnull]
return __builtin_memset(p, c, size);
>From all I can tell, this cannot happen (the function is called
either with a NULL buffer or with a -1 block number but not both),
but adding a check makes it more robust and avoids the warning.
Fixes: mmtom ("init/Kconfig: enable -O3 for all arches")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
The commit converting the driver to DMAengine was missing the flags for
the memcpy prepare call.
It went unnoticed since the omap-dma driver was ignoring them.
Fixes: 3ed6a4d1de (" mtd: onenand: omap2: Convert to use dmaengine for memcp")
Reported-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Tested-by: H. Nikolaus Schaller <hns@goldelico.com>
Tested-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Use dma_addr_t type to pass memory address and control data in
DMA descriptor fields memory_pointer and ctrl_data_ptr
To fix warning: cast to pointer from integer of different size
Signed-off-by: Vasyl Gomonovych <gomonovych@gmail.com>
Acked-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
We are currently using nand_soft_waitrdy to poll the status of the NAND
flash. FMC2 enables the wait feature bit (this feature is mandatory for
the sequencer mode). By enabling this feature, we can't poll the status
of the NAND flash, the read status command is stucked in FMC2 pipeline
until R/B# signal is high, and locks the CPU bus.
To avoid to lock the CPU bus, we poll FMC2 ISR register. This register
reports the status of the R/B# signal.
Fixes: 2cd457f328 ("mtd: rawnand: stm32_fmc2: add STM32 FMC2 NAND flash controller driver")
Signed-off-by: Christophe Kerello <christophe.kerello@st.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
ioremap has provided non-cached semantics by default since the Linux 2.6
days, so remove the additional ioremap_nocache interface.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Add MTD support for the Macronix MX25R3235F SPI NOR chip from Macronix.
The chip has 4MB of total capacity, divided into a total of 64 sectors,
each 64KB sized. The chip also supports 4KB large sectors.
Additionally, it supports dual and quad read modes.
Functionality was verified on an HPE/Aruba AP-303 board.
Signed-off-by: David Bauer <mail@david-bauer.net>
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Intel Jasper Lake has the same SPI serial flash controller as Ice Lake.
Add Jasper Lake PCI ID to the driver list of supported devices.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Add USE_FSR flag to all variants of n25q entries that support Flag Status
Register.
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Tested-by: John Garry <john.garry@huawei.com> #for n25q128a13
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Add entries for mt25q*256a and mt25q*512a flashes. These are similar to
existing n25q variants but support stateless 4 byte addressing opcodes
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
mt25q family is different from n25q family of devices, even though manf
ID and device IDs are same. mt25q flash has bit 6 set in 5th byte of
READ ID response which can be used to distinguish it from n25q variant.
mt25q flashes support stateless 4 Byte addressing opcodes where as n25q
flashes don't. Therefore, have two separate entries for mt25qu512a and
n25q512a.
Fixes: 9607af6f85 ("mtd: spi-nor: Rename "n25q512a" to "mt25qu512a (n25q512a)"")
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Tested on the Amlogic aml-libretech-pc platform which does not support
dual or quad modes
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
[tudor.ambarus@microchip.com: order entry alphabetically]
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
For GD25Q256, wrong SR bit for top/bottom selection is being used.
Fix it to use appropriate bit.
Signed-off-by: Jungseung Lee <js07.lee@samsung.com>
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
There are some flashes to use bit 6 of status register for Top/Bottom (TB).
Use top/bottom bit variable instead of fixed value and support this case.
Set the Top/Bottom (TB) mask based on SPI_NOR_TB_SR_BIT6 flash_info flag.
We can't use a bigger granularity, for example to set TB_BIT6 per
manufacturer using a SNOR_F flag. The manufacturers don't have a common
rule in regards to the TB bit:
Winbond : Use the 6th bit from 32MB capacity
W25Q20EW, W25Q50BW, W25Q128V - TB(5)
W25Q256JV, W25M512JV - TB(6)
GigaDevice : Use the 6th bit from 32MB capacity
GD25Q16C, GD25Q32C, GD25LQ32D, GD25Q64C, GD25Q128 - TB(5)
GD25Q256 - TB(6)
Micron/STM : Keep to use 5th bit
M25PX64, N25Q128A, N25Q512A, MT25QL512ABB, MT25QL02GCBB - TB(5)
Spansion : Use the 6th bit from 16MB capacity
S25FL116K, S25FL132K, S25FL165K - TB(5)
S25FL128L, S25FL256L - TB(6)
We can't make a correlation between TB and BP3 either, i.e. assume that if
BP3 is defined then TB will be at BIT(6). Micron breaks this rule.
Signed-off-by: Jungseung Lee <js07.lee@samsung.com>
[tudor.ambarus@microchip.com: describe the reason for setting a
new flash_info flag.]
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Each vendor uses different bits for SR_TB of flash.
To avoid ambiguity, rename SR_TB to indicate the bit used.
Signed-off-by: Jungseung Lee <js07.lee@samsung.com>
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
The w25q256 supports 4-byte opcodes so lets add the flag.
Tested on OpenWrt under 4.19.82 kernel on 8devices Habanero.
Signed-off-by: Robert Marko <robimarko@gmail.com>
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Here is the "big" tty and serial driver patches for 5.5-rc1. It's a bit
later in the merge window than normal as I wanted to make sure some
last-minute patches applied to it were all sane. They seem to be :)
There's a lot of little stuff in here, for the tty core, and for lots of
serial drivers:
- reverts of uartlite serial driver patches that were wrong
- msm-serial driver fixes
- serial core updates and fixes
- tty core fixes
- serial driver dma mapping api changes
- lots of other tiny fixes and updates for serial drivers
All of these have been in linux-next for a while with no reported
issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCXebFIQ8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ylnmACgjfMcfQWa7uC9Q6m2DaQaRMaW6QoAnjg+TgBB
eW9EhvyXL2VbrsuUl+iH
=Am9O
-----END PGP SIGNATURE-----
Merge tag 'tty-5.5-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull tty/serial updates from Greg KH:
"Here is the "big" tty and serial driver patches for 5.5-rc1.
It's a bit later in the merge window than normal as I wanted to make
sure some last-minute patches applied to it were all sane. They seem
to be :)
There's a lot of little stuff in here, for the tty core, and for lots
of serial drivers:
- reverts of uartlite serial driver patches that were wrong
- msm-serial driver fixes
- serial core updates and fixes
- tty core fixes
- serial driver dma mapping api changes
- lots of other tiny fixes and updates for serial drivers
All of these have been in linux-next for a while with no reported
issues"
* tag 'tty-5.5-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty: (58 commits)
Revert "serial/8250: Add support for NI-Serial PXI/PXIe+485 devices"
vcs: prevent write access to vcsu devices
tty: vt: keyboard: reject invalid keycodes
tty: don't crash in tty_init_dev when missing tty_port
serial: stm32: fix clearing interrupt error flags
tty: Fix Kconfig indentation, continued
serial: serial_core: Perform NULL checks for break_ctl ops
tty: remove unused argument from tty_open_by_driver()
tty: Fix Kconfig indentation
{tty: serial, nand: onenand}: samsung: rename to fix build warning
serial: ifx6x60: add missed pm_runtime_disable
serial: pl011: Fix DMA ->flush_buffer()
Revert "serial-uartlite: Move the uart register"
Revert "serial-uartlite: Add get serial id if not provided"
Revert "serial-uartlite: Do not use static struct uart_driver out of probe()"
Revert "serial-uartlite: Add runtime support"
Revert "serial-uartlite: Change logic how console_port is setup"
Revert "serial-uartlite: Use allocated structure instead of static ones"
tty: serial: msm_serial: Use dma_request_chan() directly for channel request
tty: serial: tegra: Use dma_request_chan() directly for channel request
...
UBI:
- Fix a regression around producing a anchor PEB for fastmap.
Due to a change in our locking fastmap was unable to produce
fresh anchors an re-used the existing one a way to often.
UBIFS:
- Fixes for endianness. A few places blindly assumed little endian.
- Fix for a memory leak in the orphan code.
- Fix for a possible crash during a commit.
- Revert a wrong bugfix.
JFFS2:
- Revert a bad bugfix in (false positive from a code checking
tool).
-----BEGIN PGP SIGNATURE-----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=LbMI
-----END PGP SIGNATURE-----
Merge tag 'upstream-5.5-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rw/ubifs
Pull UBI/UBIFS/JFFS2 updates from Richard Weinberger:
"This pull request contains mostly fixes for UBI, UBIFS and JFFS2:
UBI:
- Fix a regression around producing a anchor PEB for fastmap.
Due to a change in our locking fastmap was unable to produce fresh
anchors an re-used the existing one a way to often.
UBIFS:
- Fixes for endianness. A few places blindly assumed little endian.
- Fix for a memory leak in the orphan code.
- Fix for a possible crash during a commit.
- Revert a wrong bugfix.
JFFS2:
- Revert a bad bugfix (false positive from a code checking tool)"
* tag 'upstream-5.5-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rw/ubifs:
Revert "jffs2: Fix possible null-pointer dereferences in jffs2_add_frag_to_fragtree()"
ubi: Fix producing anchor PEBs
ubifs: ubifs_tnc_start_commit: Fix OOB in layout_in_gaps
ubifs: do_kill_orphans: Fix a memory leak bug
Revert "ubifs: Fix memory leak bug in alloc_ubifs_info() error path"
ubifs: Fix type of sup->hash_algo
ubifs: Fixed missed le64_to_cpu() in journal
ubifs: Force prandom result to __le32
ubifs: Remove obsolete TODO from dfs_file_write()
ubi: Fix warning static is not at beginning of declaration
ubi: Print skip_check in ubi_dump_vol_info()
As part of the cleanup of some remaining y2038 issues, I came to
fs/compat_ioctl.c, which still has a couple of commands that need support
for time64_t.
In completely unrelated work, I spent time on cleaning up parts of this
file in the past, moving things out into drivers instead.
After Al Viro reviewed an earlier version of this series and did a lot
more of that cleanup, I decided to try to completely eliminate the rest
of it and move it all into drivers.
This series incorporates some of Al's work and many patches of my own,
but in the end stops short of actually removing the last part, which is
the scsi ioctl handlers. I have patches for those as well, but they need
more testing or possibly a rewrite.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=lgCl
-----END PGP SIGNATURE-----
Merge tag 'compat-ioctl-5.5' of git://git.kernel.org:/pub/scm/linux/kernel/git/arnd/playground
Pull removal of most of fs/compat_ioctl.c from Arnd Bergmann:
"As part of the cleanup of some remaining y2038 issues, I came to
fs/compat_ioctl.c, which still has a couple of commands that need
support for time64_t.
In completely unrelated work, I spent time on cleaning up parts of
this file in the past, moving things out into drivers instead.
After Al Viro reviewed an earlier version of this series and did a lot
more of that cleanup, I decided to try to completely eliminate the
rest of it and move it all into drivers.
This series incorporates some of Al's work and many patches of my own,
but in the end stops short of actually removing the last part, which
is the scsi ioctl handlers. I have patches for those as well, but they
need more testing or possibly a rewrite"
* tag 'compat-ioctl-5.5' of git://git.kernel.org:/pub/scm/linux/kernel/git/arnd/playground: (42 commits)
scsi: sd: enable compat ioctls for sed-opal
pktcdvd: add compat_ioctl handler
compat_ioctl: move SG_GET_REQUEST_TABLE handling
compat_ioctl: ppp: move simple commands into ppp_generic.c
compat_ioctl: handle PPPIOCGIDLE for 64-bit time_t
compat_ioctl: move PPPIOCSCOMPRESS to ppp_generic
compat_ioctl: unify copy-in of ppp filters
tty: handle compat PPP ioctls
compat_ioctl: move SIOCOUTQ out of compat_ioctl.c
compat_ioctl: handle SIOCOUTQNSD
af_unix: add compat_ioctl support
compat_ioctl: reimplement SG_IO handling
compat_ioctl: move WDIOC handling into wdt drivers
fs: compat_ioctl: move FITRIM emulation into file systems
gfs2: add compat_ioctl support
compat_ioctl: remove unused convert_in_user macro
compat_ioctl: remove last RAID handling code
compat_ioctl: remove /dev/raw ioctl translation
compat_ioctl: remove PCI ioctl translation
compat_ioctl: remove joystick ioctl translation
...
Any arm config which has 'CONFIG_MTD_ONENAND_SAMSUNG=m' and
'CONFIG_SERIAL_SAMSUNG=m' gives a build warning:
warning: same module names found:
drivers/tty/serial/samsung.ko
drivers/mtd/nand/onenand/samsung.ko
Rename both drivers/tty/serial/samsung.c to
drivers/tty/serial/samsung_tty.c and drivers/mtd/nand/onenand/samsung.c
drivers/mtd/nand/onenand/samsung_mtd.c to fix the warning.
Signed-off-by: Sudip Mukherjee <sudipm.mukherjee@gmail.com>
Acked-by: Richard Weinberger <richard@nod.at>
Link: https://lore.kernel.org/r/20191117202435.28127-1-sudipm.mukherjee@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When a new fastmap is about to be written UBI must make sure it has a
free block for a fastmap anchor available. For this ubi_update_fastmap()
calls ubi_ensure_anchor_pebs(). This stopped working with 2e8f08deab
("ubi: Fix races around ubi_refill_pools()"), with this commit the wear
leveling code is blocked and can no longer produce free PEBs. UBI then
more often than not falls back to write the new fastmap anchor to the
same block it was already on which means the same erase block gets
erased during each fastmap write and wears out quite fast.
As the locking prevents us from producing the anchor PEB when we
actually need it, this patch changes the strategy for creating the
anchor PEB. We no longer create it on demand right before we want to
write a fastmap, but instead we create an anchor PEB right after we have
written a fastmap. This gives us enough time to produce a new anchor PEB
before it is needed. To make sure we have an anchor PEB for the very
first fastmap write we call ubi_ensure_anchor_pebs() during
initialisation as well.
Fixes: 2e8f08deab ("ubi: Fix races around ubi_refill_pools()")
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Richard Weinberger <richard@nod.at>
Compiler generates following warning when kernel is built with W=1:
drivers/mtd/ubi/ubi.h:971:1: warning: ‘static’ is not at beginning
of declaration [-Wold-style-declaration]
This commit fixes this by correctly ordering keywords.
Signed-off-by: Rishi Gupta <gupt21@gmail.com>
Signed-off-by: Richard Weinberger <richard@nod.at>
It might be interesting, if "skip_check" is set or not, so lets print
this flag in ubi_dump_vol_info() as well.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Richard Weinberger <richard@nod.at>
Cc: Boris Brezillon <boris.brezillon@collabora.com>
Cc: Heiko Schocher <hs@denx.de>
Signed-off-by: Richard Weinberger <richard@nod.at>
* Useless extra checks dropped.
* Updated the detection of the bad block markers position
Raw NAND controller drivers:
* Cadence : New driver
* Brcmnand: Support for flash-dma v0 + fixes
* Denali : Support for the legacy controller/chip DT representation
dropped
* Superfluous dev_err() calls removed
-----BEGIN PGP SIGNATURE-----
iQEzBAABCgAdFiEE9HuaYnbmDhq/XIDIJWrqGEe9VoQFAl3KwQYACgkQJWrqGEe9
VoTj1wf/Zvnk1u2vNVUaWDaHnUTAcMvjYNr1N1ppXquRXQTknZHxcgqavcwOA3yV
inHRdjQpvTPft3Pb0tddC2VBOMQTYWDGJs6JOLiPF5c4QdW/w4yHRrdnEIumbVP/
itXySbPj2QsXcRuIoEm165NTI8mdSzZFixZvCNS58r2mvMXvQbcUHsP9vjlUs9/S
XPqBlSBPKa6hC2ToIiXhgkGDQzVJ/OkCOSgG+37ATUrEqWUi9oN2KUPkbk4HSZe9
dntUIFSjeAqGjKGRGwAlt4axhnFWABfWa9xBwX9k5s4mt/FJ9QF24geemz/F1Ljp
7xd6MJu3JYoW8qBcXRRDgHuv5RNnHA==
=rpUJ
-----END PGP SIGNATURE-----
Merge tag 'nand/for-5.5' into mtd/next
Raw NAND core
* Useless extra checks dropped.
* Updated the detection of the bad block markers position
Raw NAND controller drivers:
* Cadence : New driver
* Brcmnand: Support for flash-dma v0 + fixes
* Denali : Support for the legacy controller/chip DT representation
dropped
* Superfluous dev_err() calls removed
- introduce 'struct spi_nor_controller_ops',
- clean the Register Operations methods,
- use dev_dbg insted of dev_err for low level info,
- fix retlen handling in sst_write(),
- fix silent truncations in spi_nor_read and spi_nor_read_raw(),
- fix the clearing of QE bit on lock()/unlock(),
- rework the disabling of the block write protection,
- rework the Quad Enable methods,
- make sure nor->spimem and nor->controller_ops are mutually exclusive,
- set default Quad Enable method for ISSI flashes,
- add support for few flashes.
SPI NOR controller drivers changes:
- intel-spi:
- support chips without software sequencer,
- add support for Intel Cannon Lake and Intel Comet Lake-H flashes.
-----BEGIN PGP SIGNATURE-----
iQEzBAABCAAdFiEEHUIqys8OyG1eHf7fS1VPR6WNFOkFAl3Kep8ACgkQS1VPR6WN
FOn9kgf/aKPgU6LR84YpwUKRZ4S+6K1H8SdDUt8v0FYSQ6oaTjF13fApg43WDja5
Zk0l5tlX7WIvlcRC6XKPhryZTXOKWojW1X8sguPYIZGzo7q82Eyda23jkw1QptWr
VO9L/tdK4yVUbdtp6VS/FUF31PC0DtDoCzsfBSUgrZP2srFF1BtOJNUgyuDceoxo
y3hEmINDnkaOvDDl/kbJjdEHG4PV8Vi4k0KE8deLpqlp8GDG1nkTeA1Sim7WjBPA
ZZOdg9fmGI8H8+umQEnn06H4O95T2+fX+kDMCYo4RbgWyWlGv5TidgRREmC/cSbl
YEPu6LCQoUZPVEvgolr/8Akf968ZiQ==
=i15M
-----END PGP SIGNATURE-----
Merge tag 'spi-nor/for-5.5' into mtd/next
SPI NOR core changes:
- introduce 'struct spi_nor_controller_ops',
- clean the Register Operations methods,
- use dev_dbg insted of dev_err for low level info,
- fix retlen handling in sst_write(),
- fix silent truncations in spi_nor_read and spi_nor_read_raw(),
- fix the clearing of QE bit on lock()/unlock(),
- rework the disabling of the block write protection,
- rework the Quad Enable methods,
- make sure nor->spimem and nor->controller_ops are mutually exclusive,
- set default Quad Enable method for ISSI flashes,
- add support for few flashes.
SPI NOR controller drivers changes:
- intel-spi:
- support chips without software sequencer,
- add support for Intel Cannon Lake and Intel Comet Lake-H flashes.
* Code cleanups related useless initializers and coding style issues
* Fix for a possible double free problem in cfi_cmdset_0002
* Improved error reporting and handling in cfi_cmdset_0002 core for HyperFlash
-----BEGIN PGP SIGNATURE-----
iQFEBAABCgAuFiEEyRC2zAhGcGjrhiNExEYeRXyRFuMFAl3GhtAQHHZpZ25lc2hy
QHRpLmNvbQAKCRDERh5FfJEW4/0NB/9LJZ7CQKjQOBpxypJ9LzFcXF7KHF+xaU4G
NRDJTeAng7c034tFj2tHfsICs1epidMC7OOdKZq+AJuN3M6Iq2JtqKb19r3pfQyo
S2HGQaHwrH3K8iF8ba5MBtax0xncipQgQgIAPgWZ80MdJWZKLh1F5hqhDyrO/LBR
vYG4TLmOJk5Chro5PtRytOQV/i+1VfSS7R7zleTDtCGH3pMbFOU9ySac1pDQfNmR
b36RRt119Vs6V80Sb+3L8AFfYCIcNwFySmzWJGPgmrdruTRUIeQ3II6M2HSMEYbO
oUTzxFDOTuBGrBLa3Rsq0Z9OhZk1WQqOC1f6mmfjRz/FdqiJBTXs
=K6bc
-----END PGP SIGNATURE-----
Merge CFI/Hyperbus tag 'for-v5.5-rc1' into mtd/next
CFI core changes:
* Code cleanups related useless initializers and coding style issues
* Fix for a possible double free problem in cfi_cmdset_0002
* Improved error reporting and handling in cfi_cmdset_0002 core for HyperFlash
Due to the use of sizeof(), command size set for the spi transfer
was wrong. Driver was sending and receiving always 1 byte less
and especially on write, it was hanging.
echo -n -e "\\x1\\x2\\x3\\x4" > /dev/mtd1
And read part too now works as expected.
hexdump -C -n16 /dev/mtd1
00000000 01 02 03 04 ab f3 ad c2 ab e3 f4 36 dd 38 04 15
00000010
Fixes: 4379075a87 ("mtd: mchp23k256: Add support for mchp23lcv1024")
Signed-off-by: Angelo Dureghello <angelo.dureghello@timesys.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
When calling debugfs functions, there is no need to ever check the
return value. The function can work or not, but the code logic should
never do something different based on this.
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Brian Norris <computersforpeace@gmail.com>
Cc: Marek Vasut <marek.vasut@gmail.com>
Cc: Miquel Raynal <miquel.raynal@bootlin.com>
Cc: Richard Weinberger <richard@nod.at>
Cc: Vignesh Raghavendra <vigneshr@ti.com>
Cc: Artem Bityutskiy <dedekind1@gmail.com>
Cc: linux-mtd@lists.infradead.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Set the default Quad Enable method for ISSI flashes. Used for
ISSI flashes (IS25WP256D-JMLE) that do not support SFDP tables
and can not determine the Quad Enable method by parsing BFPT.
Based on code originally written by Wesley Terpstra <wesley@sifive.com>
and/or Palmer Dabbelt <palmer@sifive.com>
c94e267766
Signed-off-by: Sagar Shrikant Kadam <sagar.kadam@sifive.com>
[tudor.ambarus@microchip.com:
- rebase, split and adapt for latest spi-nor/next,
- use PMC CFI ID for ISSI. According to JEP106BA, "Programmable Micro Corp"
changed its name to Integrated Silicon Solution (ISSI)]
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Reviewed-by: Vignesh Raghavendra <vigneshr@ti.com>
Update the spi_nor_id table for is25wp256 (32MB) device from ISSI,
present on HiFive Unleashed dev board (Rev: A00).
Use the post bfpt fixup hook for the is25wp256 device, as done for
the is25lp256 device to overwrite the wrong address width advertised
by BFPT.
Signed-off-by: Sagar Shrikant Kadam <sagar.kadam@sifive.com>
[tudor.ambarus@microchip.com: rebase, split and adapt for latest spi-nor/next]
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Reviewed-by: Vignesh Raghavendra <vigneshr@ti.com>
Add MTD support for w25q256jw SPI NOR chip from Winbond. This chip
supports dual/quad I/O mode with 512 blocks of memory organized in
64KB sectors. In addition to this, there is also small 4KB sectors
available for flexibility. The device has been validated using Thor96
board.
Cc: Marek Vasut <marek.vasut@gmail.com>
Cc: Tudor Ambarus <tudor.ambarus@microchip.com>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Brian Norris <computersforpeace@gmail.com>
Cc: Miquel Raynal <miquel.raynal@bootlin.com>
Cc: Richard Weinberger <richard@nod.at>
Cc: Vignesh Raghavendra <vigneshr@ti.com>
Cc: linux-mtd@lists.infradead.org
Signed-off-by: Darshak Patel <darshak.patel@einfochips.com>
[Mani: cleaned up for upstream]
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
When the controller is not under the SPI-MEM interface it may implement
the optional controller_ops->erase() method.
nor->spimem and nor->controller_ops are mutually exclusive. Move the
nor->controller_ops->erase != NULL check as an 'else if' case to
nor->spimem, in order to avoid the nor->controller_ops != NULL
check.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Reviewed-by: Boris Brezillon <boris.brezillon@collabora.com>
Expand the spi_nor_check() to make sure that nor->spimem and
nor->controller_ops are mutually exclusive.
Fixes: b35b9a1036 ("mtd: spi-nor: Move m25p80 code in spi-nor.c")
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Reviewed-by: Boris Brezillon <boris.brezillon@collabora.com>
Rename macronix_quad_enable() to a generic name:
spi_nor_sr1_bit6_quad_enable().
Prepend "spi_nor_" to "sr2_bit7_quad_enable". All SPI NOR generic
methods should be prepended by "spi_nor_".
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Reviewed-by: Vignesh Raghavendra <vigneshr@ti.com>
Merge
spansion_no_read_cr_quad_enable()
spansion_read_cr_quad_enable()
into
spi_nor_sr2_bit1_quad_enable().
Reduce code duplication by introducing spi_nor_write_16bit_cr_and_check().
The Configuration Register contains bits that can be updated in future:
FREEZE, CMP. Provide a generic method that allows updating all bits
of the Configuration Register.
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Reviewed-by: Vignesh Raghavendra <vigneshr@ti.com>
JEDEC Basic Flash Parameter Table, 15th DWORD, bits 22:20,
refers to this bit as "bit 1 of the status register 2".
Rename the macro accordingly.
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Reviewed-by: Vignesh Raghavendra <vigneshr@ti.com>
Test that all the bits from Status Register 1 and Status Register 2
were written correctly.
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Reviewed-by: Vignesh Raghavendra <vigneshr@ti.com>
spi_nor_unlock() unlocks blocks of memory or the entire flash memory
array, if requested. clear_sr_bp() unlocks the entire flash memory
array at boot time. This calls for some unification, clear_sr_bp() is
just an optimization for the case when the unlock request covers the
entire flash size.
Get rid of clear_sr_bp() and introduce spi_nor_unlock_all(), which is
just a call to spi_nor_unlock() for the entire flash memory array.
This fixes a bug that was present in spi_nor_spansion_clear_sr_bp().
When the QE bit was zero, we used the Write Status (01h) command with
one data byte, which might cleared the Status Register 2. We now always
use the Write Status (01h) command with two data bytes when
SNOR_F_HAS_16BIT_SR is set, to avoid clearing the Status Register 2.
The SNOR_F_NO_READ_CR case is treated as well. When the flash doesn't
support the CR Read command, we make an assumption about the value of
the QE bit. In spi_nor_init(), call spi_nor_quad_enable() first, then
spi_nor_unlock_all(), so that at the spi_nor_unlock_all() time we can
be sure the QE bit has value one, because of the previous call to
spi_nor_quad_enable().
Get rid of the MFR handling and implement specific manufacturer
default_init() fixup hooks.
Note that this changes a bit the logic for the SNOR_MFR_ATMEL,
SNOR_MFR_INTEL and SNOR_MFR_SST cases. Before this patch, the Atmel,
Intel and SST chips did not set the locking ops, but unlocked the entire
flash at boot time, while now they are setting the locking ops to
stm_locking_ops. This should work, since the disable of the block
protection at the boot time used the same Status Register bits to unlock
the flash, as in the stm_locking_ops case.
Suggested-by: Boris Brezillon <boris.brezillon@collabora.com>
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Reviewed-by: Vignesh Raghavendra <vigneshr@ti.com>
Make sure that when doing a lock() or an unlock() operation we don't clear
the QE bit from Status Register 2.
JESD216 revB or later offers information about the *default* Status
Register commands to use (see BFPT DWORDS[15], bits 22:20). In this
standard, Status Register 1 refers to the first data byte transferred on a
Read Status (05h) or Write Status (01h) command. Status register 2 refers
to the byte read using instruction 35h. Status register 2 is the second
byte transferred in a Write Status (01h) command.
Industry naming and definitions of these Status Registers may differ.
The definitions are described in JESD216B, BFPT DWORDS[15], bits 22:20.
There are cases in which writing only one byte to the Status Register 1
has the side-effect of clearing Status Register 2 and implicitly the Quad
Enable bit. This side-effect is hit just by the
BFPT_DWORD15_QER_SR2_BIT1_BUGGY and BFPT_DWORD15_QER_SR2_BIT1 cases.
Suggested-by: Boris Brezillon <boris.brezillon@collabora.com>
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Reviewed-by: Vignesh Raghavendra <vigneshr@ti.com>
The commit 4844ef8030 ("mtd: cfi_cmdset_0002: Add support for polling
status register") added checking for the status register error bits into
chip_good() to only return 1 if these bits are 0s. Unfortunately, this
means that polling using chip_good() always reaches a timeout condition
when erase or program failure bits are set. Let's fully delegate the task
of determining the error conditions to cfi_check_err_status() and make
chip_good() only look for the Device Ready/Busy condition.
Fixes: 4844ef8030 ("mtd: cfi_cmdset_0002: Add support for polling status register")
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Cypress S26K{L|S}P{128|256|512}S datasheet says that the error bits in
the status register are only valid when the "device ready" bit 7 is set.
Add the check for the device ready bit in cfi_check_err_status() as that
function isn't always called with this bit set.
Fixes: 4844ef8030 ("mtd: cfi_cmdset_0002: Add support for polling status register")
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Else there may be a double-free problem, because cfi->cfiq will
be freed by mtd_do_chip_probe() if both the two invocations of
check_cmd_set() return failure.
Signed-off-by: Hou Tao <houtao1@huawei.com>
Reviewed-by: Richard Weinberger <richard@nod.at>
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
The 'ret' local variables are typically initialized to 0 but this value is
often unused, thus we can kill those initializers.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Use DIV_ROUND_UP() in cfi_udelay() instead of open-coding it...
Doing this also helpfully gets rid of two complaints from
'scripts/checkpatch.pl --strict':
CHECK: spaces preferred around that '+' (ctx:VxV)
#29: FILE: drivers/mtd/chips/cfi_util.c:29:
+ msleep((us+999)/1000);
^
CHECK: spaces preferred around that '/' (ctx:VxV)
#29: FILE: drivers/mtd/chips/cfi_util.c:29:
+ msleep((us+999)/1000);
^
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Check that all the bits written in the write_sr_and_check() method
match the status_new received value. Failing to write the other bits
is dangerous too, extend the check.
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Reviewed-by: Vignesh Raghavendra <vigneshr@ti.com>
When the Read-Modify-Write-Read-Back Quad Enable methods failed on
the Read-Back, they returned -EINVAL. Since this is an I/O error,
return -EIO.
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Reviewed-by: Vignesh Raghavendra <vigneshr@ti.com>
Drop the default spansion_quad_enable() method and replace it with
spansion_read_cr_quad_enable().
The function was buggy, it didn't care about the previous values
of the Status and Configuration Registers. spansion_read_cr_quad_enable()
is a Read-Modify-Write-Check function that keeps track of what were
the previous values of the Status and Configuration Registers.
In terms of instruction types sent to the flash, the only difference
between the spansion_quad_enable() and spansion_read_cr_quad_enable()
is that the later calls spi_nor_read_sr(). We can safely assume that all
flashes support spi_nor_read_sr(), because all flashes call it in
spi_nor_sr_ready(). The transition from spansion_quad_enable() to
spansion_read_cr_quad_enable() will not affect anybody, drop the buggy
code.
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Reviewed-by: Vignesh Raghavendra <vigneshr@ti.com>
Merge
static int spi_nor_write_sr(struct spi_nor *nor, u8 val)
static int spi_nor_write_sr_cr(struct spi_nor *nor, const u8 *sr_cr)
into
static int spi_nor_write_sr(struct spi_nor *nor, const u8 *sr, size_t len)
The Status Register can be written with one or two bytes. Merge
the two functions to avoid code duplication.
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Reviewed-by: Boris Brezillon <boris.brezillon@collabora.com>
Avoid duplicating code by moving the calls to spi_nor_write_enable() and
spi_nor_wait_till_ready() inside the Write Status Register methods.
Move spi_nor_write_sr() to avoid forward declaration of
spi_nor_wait_till_ready().
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Reviewed-by: Boris Brezillon <boris.brezillon@collabora.com>
spi_nor_clear_sr() and spi_nor_clear_fsr() are called just in case
of errors. The callers didn't check their return value, make them
of type void.
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Reviewed-by: Boris Brezillon <boris.brezillon@collabora.com>
Rename 'sst_write_err' label to 'out' as it is no longer generic for
all the errors in the sst_write() method, and may introduce confusion.
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Reviewed-by: Boris Brezillon <boris.brezillon@collabora.com>
Check for the return vales of each Register Operation.
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Reviewed-by: Vignesh Raghavendra <vigneshr@ti.com>
What most users care about is "my dev is not working properly".
All low level information should be discovered when activating
the debug traces.
Keep error messages just for the following cases:
- when the SR/FSR report program or erase fails, or attempts of
modifying a protected sector,
- when the JEDEC ID is not recognized,
- when the resume() call fails,
- when the spi_nor_check() fails.
Suggested-by: Boris Brezillon <boris.brezillon@collabora.com>
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Reviewed-by: Vignesh Raghavendra <vigneshr@ti.com>
spi_nor_read_raw() assigns the result of 'ssize_t spi_nor_read_data()'
to the 'int ret' variable, while 'ssize_t' is a 64-bit type and *int*
is a 32-bit type on the 64-bit machines. This silent truncation isn't
really valid, so fix up the variable's type.
Fixes: f384b352cb ("mtd: spi-nor: parse Serial Flash Discoverable Parameters (SFDP) tables")
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
spi_nor_read() assigns the result of 'ssize_t spi_nor_read_data()'
to the 'int ret' variable, while 'ssize_t' is a 64-bit type and *int*
is a 32-bit type on the 64-bit machines. This silent truncation isn't
really valid, so fix up the variable's type.
Fixes: 59451e1233 ("mtd: spi-nor: change return value of read/write")
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Intel Comet Lake-H PCH has the same SPI serial flash controller as Comet
Lake-LP. Add Comet Lake-H PCI ID to the driver list of supported devices.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Print identifying information about struct device.
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Reviewed-by: Boris Brezillon <boris.brezillon@collabora.com>
Constify the data to write to the Status Register.
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Reviewed-by: Boris Brezillon <boris.brezillon@collabora.com>
In case the write of the first byte failed, retlen was incorrectly
incremented to *retlen += actual; on the exit path. retlen should be
incremented when actual data was written to the flash.
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Reviewed-by: Boris Brezillon <boris.brezillon@collabora.com>
Drop the error messages from the callers, since the callees
already print an error message in case of failure.
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Reviewed-by: Boris Brezillon <boris.brezillon@collabora.com>
Let the callers pass the pointer to the DMA-able buffer where
the value of the Configuration Register will be written. This way we
avoid the casts between int and u8, which can be confusing.
Callers stop compare the return value of spi_nor_read_cr() with negative,
spi_nor_read_cr() returns 0 on success and -errno otherwise.
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Reviewed-by: Boris Brezillon <boris.brezillon@collabora.com>
Let the callers pass the pointer to the DMA-able buffer where
the value of the Flag Status Register will be written. This way we
avoid the casts between int and u8, which can be confusing.
Caller stops compare the return value of spi_nor_read_fsr() with negative,
spi_nor_read_fsr() returns 0 on success and -errno otherwise.
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Reviewed-by: Boris Brezillon <boris.brezillon@collabora.com>
Let the callers pass the pointer to the DMA-able buffer where
the value of the Status Register will be written. This way we
avoid the casts between int and u8, which can be confusing.
Callers stop compare the return value of spi_nor_read_sr() with negative,
spi_nor_read_sr() returns 0 on success and -errno otherwise.
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Reviewed-by: Boris Brezillon <boris.brezillon@collabora.com>
Do not overwrite the error numbers received the Register Operations
methods.
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Reviewed-by: Boris Brezillon <boris.brezillon@collabora.com>
spi_mem_exec_op()
nor->controller_ops->write_reg()
nor->controller_ops->read_reg()
spi_nor_wait_till_ready()
Return 0 on success, -errno otherwise.
Stop compare with negative and compare with zero in all the register
operations methods.
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Reviewed-by: Boris Brezillon <boris.brezillon@collabora.com>
Group all register methods up in the file, to avoid forward
declarations.
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Reviewed-by: Boris Brezillon <boris.brezillon@collabora.com>
Two new lines, one after another, drop one.
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Reviewed-by: Boris Brezillon <boris.brezillon@collabora.com>
All the core functions should begin with "spi_nor_".
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Reviewed-by: Boris Brezillon <boris.brezillon@collabora.com>
Remove unecessary checking if dmac is NULL.
If Cadence nand controller driver uses DMA engine then cdns_ctrl->dmac
cannot be NULL. It is verified during driver initialization.
If Cadence nand controller driver does not use DMA engine then
CPU IO read/write are executed instead of slave DMA transfer.
In that case cdns_ctrl->dmac is not used at all.
Reported-by: kbuild test robot <lkp@intel.com>
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Piotr Sroka <piotrs@cadence.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
platform_get_irq() will call dev_err() itself on failure,
so there is no need for the driver to also do this.
This is detected by coccinelle.
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
platform_get_irq() will call dev_err() itself on failure,
so there is no need for the driver to also do this.
This is detected by coccinelle.
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Sparse complained about the following:
drivers/mtd/nand/raw/brcmnand/brcmnand.c:921:40: warning: Using plain integer as NULL pointer
fix this issue by assigning the pointer to NULL.
Fixes: c1ac2dc34b ("mtd: rawnand: brcmnand: When oops in progress use pio and interrupt polling")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Commit d8e8fd0ebf ("mtd: rawnand: denali: decouple controller and
NAND chips") supported the new binding for the separate controller/chip
representation, keeping the backward compatibility.
All the device trees in upstream migrated to the new binding.
Remove the support for the old binding.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Any write with either dd or flashcp to a device driven by the
spear_smi.c driver will pass through the spear_smi_cpy_toio()
function. This function will get called for chunks of up to 256 bytes.
If the amount of data is smaller, we may have a problem if the data
length is not 4-byte aligned. In this situation, the kernel panics
during the memcpy:
# dd if=/dev/urandom bs=1001 count=1 of=/dev/mtd6
spear_smi_cpy_toio [620] dest c9070000, src c7be8800, len 256
spear_smi_cpy_toio [620] dest c9070100, src c7be8900, len 256
spear_smi_cpy_toio [620] dest c9070200, src c7be8a00, len 256
spear_smi_cpy_toio [620] dest c9070300, src c7be8b00, len 233
Unhandled fault: external abort on non-linefetch (0x808) at 0xc90703e8
[...]
PC is at memcpy+0xcc/0x330
The above error occurs because the implementation of memcpy_toio()
tries to optimize the number of I/O by writing 4 bytes at a time as
much as possible, until there are less than 4 bytes left and then
switches to word or byte writes.
Unfortunately, the specification states about the Write Burst mode:
"the next AHB Write request should point to the next
incremented address and should have the same size (byte,
half-word or word)"
This means ARM architecture implementation of memcpy_toio() cannot
reliably be used blindly here. Workaround this situation by update the
write path to stick to byte access when the burst length is not
multiple of 4.
Fixes: f18dbbb1bf ("mtd: ST SPEAr: Add SMI driver for serial NOR flash")
Cc: Russell King <linux@armlinux.org.uk>
Cc: Boris Brezillon <boris.brezillon@collabora.com>
Cc: stable@vger.kernel.org
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Russell King <rmk+kernel@armlinux.org.uk>
In order to support device tree probing of IXP4xx NOR flash
chips, a certain big-endian or mixed-endian memory access
pattern need to be used.
I have opted to use the pattern set by previous plug-ins
to physmap for Gemini and Versatile, just override some
functions and reuse most of the physmap core code as it
is to minimize maintenance.
Parts of drivers/mtd/ixp4xx.c are copied into this file.
After we have IXP4xx converted fully to device tree, the
drivers/mtd/ixp4xx.c file will be deleted and this will
be the only access pattern to the IXP4xx flash.
I did not keep the quirk in the flash write function
after probe, where the old code for a while checks for
access to odd addresses, fails and assigns a "faster"
write function once it has convinced probe to only use
2-byte accesses. As we mandate that this device should
be using bank-width = <2> this should not be a problem
unless misconfigured.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Avoid printing the address of l440gx_map.virt every time l440gx init.
Signed-off-by: Fuqian Huang <huangfq.daxian@gmail.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Each of these drivers has a copy of the same trivial helper function to
convert the pointer argument and then call the native ioctl handler.
We now have a generic implementation of that, so use it.
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Acked-by: David S. Miller <davem@davemloft.net>
Acked-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Reviewed-by: Jason Gunthorpe <jgg@mellanox.com>
Reviewed-by: Jiri Kosina <jkosina@suse.cz>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Reviewed-by: Cornelia Huck <cohuck@redhat.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
n_tx was never used, drop it. Replace 'const u8 *txbuf' with 'u8 opcode',
to comply with the SPI NOR int (*read_reg)() method. The 'const'
qualifier has no meaning for parameters passed by value, drop it.
Going furher, the opcode was passed to cqspi_calc_rdreg() and never used,
drop it.
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Reviewed-by: Boris Brezillon <boris.brezillon@collabora.com>
Move all SPI NOR controller driver specific ops in a dedicated
structure. 'struct spi_nor' becomes lighter.
Use size_t for lengths in 'int (*write_reg)()' and 'int (*read_reg)()'.
Rename wite/read_buf to buf, the name of the functions are
suggestive enough. Constify buf in int (*write_reg). Comply with these
changes in the SPI NOR controller drivers.
Suggested-by: Boris Brezillon <boris.brezillon@collabora.com>
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Reviewed-by: Boris Brezillon <boris.brezillon@collabora.com>
The pointer to 'struct spi_nor' is kzalloc'ed above in the code.
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Reviewed-by: Boris Brezillon <boris.brezillon@collabora.com>
Some flash controllers don't have a software sequencer. Avoid
configuring the register addresses for it, and double check
everywhere that its not accidentally trying to be used.
Every use of `sregs` is now guarded by a check of `sregs` or
`swseq_reg`. The check might be done in the calling function.
Signed-off-by: Jethro Beekman <jethro@fortanix.com>
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
The 'region' field in struct stfsm is unused and can be removed.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Most of the time the ooboffs parameter of the mtd_oob_ops structure
was initialized only when needed. Since the introduction of the
SPI-NAND subsystem, this parameter is transferred into
nand_page_io_req structure automatically and may be used by any
SPI-NAND user.
Before this happens, initialize all the structure parameters when they
are created in mtdchar.c.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Fixes gcc '-Wunused-but-set-variable' warning:
drivers/mtd/devices/spear_smi.c: In function spear_smi_probe_config_dt:
drivers/mtd/devices/spear_smi.c:780:32: warning: variable flash_info set but not used [-Wunused-but-set-variable]
It is not used since commit 6551ab5d30 ("mtd:
add device-tree support to spear_smi")
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: zhengbin <zhengbin13@huawei.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
We don't need dev_err() messages when platform_get_irq() fails now that
platform_get_irq() prints an error message itself when something goes
wrong. Let's remove these prints with a simple semantic patch.
// <smpl>
@@
expression ret;
struct platform_device *E;
@@
ret =
(
platform_get_irq(E, ...)
|
platform_get_irq_byname(E, ...)
);
if ( \( ret < 0 \| ret <= 0 \) )
{
(
-if (ret != -EPROBE_DEFER)
-{ ...
-dev_err(...);
-... }
|
...
-dev_err(...);
)
...
}
// </smpl>
While we're here, remove braces on if statements that only have one
statement (manually).
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Brian Norris <computersforpeace@gmail.com>
Cc: Marek Vasut <marek.vasut@gmail.com>
Cc: Miquel Raynal <miquel.raynal@bootlin.com>
Cc: Richard Weinberger <richard@nod.at>
Cc: Vignesh Raghavendra <vigneshr@ti.com>
Cc: linux-mtd@lists.infradead.org
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Stephen Boyd <swboyd@chromium.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Commit 7e534323c4 ("mtd: rawnand: Pass a nand_chip object to
chip->read_xxx() hooks") modified the prototype of the struct nand_chip
read_buf function pointer. In the au1550nd driver we have 2
implementations of read_buf. The previously mentioned commit modified
the au_read_buf() implementation to match the function pointer, but not
au_read_buf16(). This results in a compiler warning for MIPS
db1xxx_defconfig builds:
drivers/mtd/nand/raw/au1550nd.c:443:57:
warning: pointer type mismatch in conditional expression
Fix this by updating the prototype of au_read_buf16() to take a struct
nand_chip pointer as its first argument, as is expected after commit
7e534323c4 ("mtd: rawnand: Pass a nand_chip object to chip->read_xxx()
hooks").
Note that this shouldn't have caused any functional issues at runtime,
since the offset of the struct mtd_info within struct nand_chip is 0
making mtd_to_nand() effectively a type-cast.
Signed-off-by: Paul Burton <paul.burton@mips.com>
Fixes: 7e534323c4 ("mtd: rawnand: Pass a nand_chip object to chip->read_xxx() hooks")
Cc: stable@vger.kernel.org # v4.20+
Reviewed-by: Boris Brezillon <boris.brezillon@collabora.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Yoshio Furuyama