QCA6390 memdump VSE sometimes come to bluetooth driver
with wrong sequence number as illustrated as follows:
frame # in dec: frame data in hex
1396: ff fd 01 08 74 05 00 37 8f 14
1397: ff fd 01 08 75 05 00 ff bf 38
1414: ff fd 01 08 86 05 00 fb 5e 4b
1399: ff fd 01 08 77 05 00 f3 44 0a
1400: ff fd 01 08 78 05 00 ca f7 41
it is mistook for controller missing packets, so results
in page fault after overwriting memdump buffer allocated.
Fixed by ignoring QCA6390 sequence number check and
checking buffer space before writing.
Signed-off-by: Zijun Hu <zijuhu@codeaurora.org>
Tested-by: Zijun Hu <zijuhu@codeaurora.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
serdev_device_write() is not appropriate at here because
serdev_device_write_wakeup() is not used to release completion hold
by the former at @write_wakeup member of struct serdev_device_ops.
Fix by using serdev_device_write_buf() instead of serdev_device_write().
Signed-off-by: Zijun Hu <zijuhu@codeaurora.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Controller ID info got by VSC EDL_PATCH_GETVER is very
important, so improve its log level from DEBUG to INFO.
Signed-off-by: Zijun Hu <zijuhu@codeaurora.org>
Reviewed-by: Matthias Kaehlcke <mka@chromium.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Warm reboot can not reset controller qca6390 due to
lack of controllable power supply, so causes firmware
download failure during enable.
Fixed by sending VSC EDL_SOC_RESET to reset qca6390
within added device shutdown implementation.
Signed-off-by: Zijun Hu <zijuhu@codeaurora.org>
Tested-by: Zijun Hu <zijuhu@codeaurora.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Calls of the functions clk_disable_unprepare() and hci_free_dev()
were missing for the exception handling.
Thus add the missed function calls together with corresponding
jump targets.
Fixes: 055825614c ("Bluetooth: btmtkuart: add an implementation for clock osc property")
Signed-off-by: Chuhong Yuan <hslester96@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
@dev parameter of qca_suspend()/qca_resume() represents
serdev_device, but it is mistook for hci_dev and causes
succedent unexpected memory access.
Fix by taking @dev as serdev_device.
Fixes: 41d5b25fed ("Bluetooth: hci_qca: add PM support")
Signed-off-by: Zijun Hu <zijuhu@codeaurora.org>
Reviewed-by: Matthias Kaehlcke <mka@chromium.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Added new Broadcom device BCM4350C5, changed BCM4354A2 to BCM4356A2.
Based on Broadcom Windows drivers 001.003.015 should be BCM4356A2. I
have user report that firmware name is misplaced
(https://github.com/winterheart/broadcom-bt-firmware/issues/3).
Signed-off-by: Azamat H. Hackimov <azamat.hackimov@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
hdev is always allocated and not only when power control is required.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Abhishek Pandit-Subedi <abhishekpandit@chromium.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
WCN3991 supports transparent WBS (host encoded mSBC). Add a flag to the
device match data to show WBS is supported.
This requires the matching firmware for WCN3991 in linux-firmware:
1a8b0dc00f77 (qca: Enable transparent WBS for WCN3991)
Signed-off-by: Abhishek Pandit-Subedi <abhishekpandit@chromium.org>
Reviewed-by: Matthias Kaehlcke <mka@chromium.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
serdev_device_ops is not modified and can be const. Also, remove the
unneeded declaration of it.
Output from the file command before and after:
Before:
text data bss dec hex filename
7192 2408 192 9792 2640 drivers/bluetooth/hci_serdev.o
After:
text data bss dec hex filename
7256 2344 192 9792 2640 drivers/bluetooth/hci_serdev.o
Signed-off-by: Rikard Falkeborn <rikard.falkeborn@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Implement the prevent_wake hook by checking device_may_wakeup on the usb
interface. This prevents the Bluetooth core from enabling scanning when
the device isn't expected to wake from suspend.
Signed-off-by: Abhishek Pandit-Subedi <abhishekpandit@chromium.org>
Reviewed-by: Alain Michaud <alainm@chromium.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
RTL8723BS is often used in ARM boards, so add ability to bind it
using device tree.
Signed-off-by: Vasily Khoruzhick <anarsoul@gmail.com>
Signed-off-by: Alistair Francis <alistair@alistair23.me>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Move the read of max-speed from device-tree out of the qca_is_wcn399x
if block so oper_speed can be set for QCA9377 devices as well.
Suggested-by: Abhishek Pandit-Subedi <abhishekpandit@chromium.org>
Signed-off-by: Christian Hewitt <christianshewitt@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Add a compatible so QCA9377 devices can be defined in device-tree.
Signed-off-by: Christian Hewitt <christianshewitt@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This change adds support for LE scatternet connections to Intel's JfP
and ThP controllers.
Signed-off-by: Alain Michaud <alainm@chromium.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This change adds the relevant driver and quirk to allow drivers to
report the le_states as being trustworthy.
This has historically been disabled as controllers did not reliably
support this. In particular, this will be used to relax this condition
for controllers that have been well tested and reliable.
/* Most controller will fail if we try to create new connections
* while we have an existing one in slave role.
*/
if (hdev->conn_hash.le_num_slave > 0)
return NULL;
Signed-off-by: Alain Michaud <alainm@chromium.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Currently the bcm_uart_subver_ and bcm_usb_subver_table-s lack entries
for the BCM4324B5 and BCM20703A1 chipsets. This makes the code use just
"BCM" as prefix for the filename to pass to request-firmware, making it
harder for users to figure out which firmware they need. This especially
is problematic with the UART attached BCM4324B5 where this leads to the
filename being just "BCM.hcd".
Add the 2 missing devices to subver tables. This has been tested on:
1. A Dell XPS15 9550 where this makes btbcm.c try to load
"BCM20703A1-0a5c-6410.hcd" before it tries to load "BCM-0a5c-6410.hcd".
2. A Thinkpad 8 where this makes btbcm.c try to load
"BCM4324B5.hcd" before it tries to load "BCM.hcd"
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Currently the bcm_uart_subver_ and bcm_usb_subver_table-s lack entries
for various newer chipsets. This makes the code use just "BCM" as prefix
for the filename to pass to request-firmware, making it harder for users
to figure out which firmware they need. This especially a problem with
UART attached devices where this leads to the filename being "BCM.hcd".
If we add new entries to the subver-tables now, then this will change
what firmware file the kernel looks for, e.g. currently linux-firmware
contains a brcm/BCM-0bb4-0306.hcd file. If we add the info for the
BCM20703A1 to the subver table, then this will change to
brcm/BCM20703A1-0bb4-0306.hcd. This will cause the file to no longer
get loaded breaking Bluetooth for existing users, going against the
no regressions policy.
To avoid this regression make the btbcm code try multiple filenames,
first try the fullname, e.g. BCM20703A1-0bb4-0306.hcd and if that is
not found, then fallback to the name with just BCM as prefix.
This commit also adds an info message which filename was used,
this makes the output look like this for example:
[ 57.387867] Bluetooth: hci0: BCM20703A1
[ 57.387870] Bluetooth: hci0: BCM20703A1 (001.001.005) build 0000
[ 57.389438] Bluetooth: hci0: BCM20703A1 'brcm/BCM20703A1-0a5c-6410.hcd' Patch
[ 58.681769] Bluetooth: hci0: BCM20703A1 Generic USB 20Mhz fcbga_BU
[ 58.681772] Bluetooth: hci0: BCM20703A1 (001.001.005) build 0481
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
If we have already loaded the firmware/patchram and btbcm_initialize()
is called to re-init the HCI after this then there is no need to get
the USB device-ids and build a firmware-filename out of these.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
On UART attached devices we do:
1. btbcm_initialize()
2. Setup UART baudrate, etc.
3. btbcm_finalize()
After our previous changes we can now also use btbcm_finalize() from
the btbcm_setup_patchram() function used on USB devices without any
functional changes. This completes unifying the USB and UART paths
as much as possible.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Make btbcm_initialize() get and print the device's local-name on re-init
too, this will make us also print the local-name after loading the
Patch on UART attached devices making things more consistent.
This also removes some code duplication from btbcm_setup_patchram()
and allows more code duplication removal there in a follow-up patch.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Instead of having btbcm_initialize() fill a passed in fw_name buffer
and then have its callers use that to request the firmware + load
it into the HCI, make btbcm_initialize() do this itself the first
time it is called (its get called a second time to reset the HCI
after the firmware has been loaded).
This removes some code duplication and makes it easier for further
patches in this series to try more then 1 firmware filename.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
btbcm_finalize() is currently only used by UART attached BCM devices.
Move the setting of the USE_BDADDR_PROPERTY quirk, which we only want
for UART attached devices to hci_bcm in preparation for using
btbcm_finalize() for USB attached devices too.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
btbcm_initialize() must either return an error; or fill the passed in
fw_name, otherwise we end up passing uninitialized stack memory to
request_firmware().
Since we have a fallback hw_name of "BCM" not having a known version
in the subver field does not matter, drop the check so that we always
fill the passed in fw_name.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The new btusb_find_altsetting() dereferences it without checking
the check is added in this patch
Signed-off-by: Sathish Narasimman <sathish.narasimman@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
In case the controller is already in operation mode, the Intel specific
events will not be enabled. Fix this by jumping to a common finish
section that will allow setting final details for the controller.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
For mSBC encoded audio stream over usb transport, btusb driver
to be set to alternate settings 6 as per BT core spec 5.0. The
type of air mode is used to differenting which alt setting to be
used.
The changes are made considering some discussion over the similar
patch submitted earlier from Kuba Pawlak (link below)
https://www.spinics.net/lists/linux-bluetooth/msg64577.html
Reported-by: kbuild test robot <lkp@intel.com>
Signed-off-by: Sathish Narasimman <sathish.narasimman@intel.com>
Signed-off-by: Chethan T N <chethan.tumkur.narayan@intel.com>
Signed-off-by: Hsin-Yu Chao <hychao@chromium.org>
Signed-off-by: Amit K Bag <amit.k.bag@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
When BT module can't be initialized, but it has an IRQ, unloading
the driver WARNs when trying to free not-yet-requested IRQ. Fix it by
noting whether the IRQ was requested.
WARNING: CPU: 2 PID: 214 at kernel/irq/devres.c:144 devm_free_irq+0x49/0x4ca
[...]
WARNING: CPU: 2 PID: 214 at kernel/irq/manage.c:1746 __free_irq+0x8b/0x27c
Trying to free already-free IRQ 264
Modules linked in: hci_uart(-) btbcm bluetooth ecdh_generic ecc libaes
CPU: 2 PID: 214 Comm: rmmod Tainted: G W 5.6.1mq-00044-ga5f9ea098318-dirty #928
[...]
[<b016aefb>] (devm_free_irq) from [<af8ba1ff>] (bcm_close+0x97/0x118 [hci_uart])
[<af8ba1ff>] (bcm_close [hci_uart]) from [<af8b736f>] (hci_uart_unregister_device+0x33/0x3c [hci_uart])
[<af8b736f>] (hci_uart_unregister_device [hci_uart]) from [<b035930b>] (serdev_drv_remove+0x13/0x20)
[<b035930b>] (serdev_drv_remove) from [<b037093b>] (device_release_driver_internal+0x97/0x118)
[<b037093b>] (device_release_driver_internal) from [<b0370a0b>] (driver_detach+0x2f/0x58)
[<b0370a0b>] (driver_detach) from [<b036f855>] (bus_remove_driver+0x41/0x94)
[<b036f855>] (bus_remove_driver) from [<af8ba8db>] (bcm_deinit+0x1b/0x740 [hci_uart])
[<af8ba8db>] (bcm_deinit [hci_uart]) from [<af8ba86f>] (hci_uart_exit+0x13/0x30 [hci_uart])
[<af8ba86f>] (hci_uart_exit [hci_uart]) from [<b01900bd>] (sys_delete_module+0x109/0x1d0)
[<b01900bd>] (sys_delete_module) from [<b0101001>] (ret_fast_syscall+0x1/0x5a)
[...]
Cc: stable@vger.kernel.org
Fixes: 6cc4396c88 ("Bluetooth: hci_bcm: Add wake-up capability")
Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The IRQ polarity is be configured in bcm_setup_sleep(). Make the
configured value match what is in the DeviceTree.
Cc: stable@vger.kernel.org
Fixes: f25a96c8eb ("Bluetooth: hci_bcm: enable IRQ capability from devicetree")
Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch adds support for QCA6390, including the devicetree and acpi
compatible hwid matching, and patch/nvm downloading.
Signed-off-by: Rocky Liao <rjliao@codeaurora.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
To determine the build version of Bluetooth firmware to ensure reported
issue related to a particular release. This is very helpful for every fw
downloaded to BT controller and issue reported from field test.
Signed-off-by: Amit K Bag <amit.k.bag@intel.com>
Signed-off-by: Sukumar Ghorai <sukumar.ghorai@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
All HCI device specific error messages shall use bt_dev_err to indicate
the device name in the message.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
All HCI device specific error messages shall use bt_dev_err to indicate
the device name in the message.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
This change introduces a wide band speech setting which allows higher
level clients to query the local controller support for wide band speech
as well as set the setting state when the radio is powered off.
Internally, this setting controls if erroneous data reporting is enabled
on the controller.
Signed-off-by: Alain Michaud <alainm@chromium.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch replaces devm_gpiod_get() with devm_gpiod_get_optional() to get
bt_en and replaces devm_clk_get() with devm_clk_get_optional() to get
susclk. It also uses NULL check to determine whether the resource is
available or not.
Fixes: 8a208b24d7 ("Bluetooth: hci_qca: Make bt_en and susclk not mandatory for QCA Rome")
Signed-off-by: Rocky Liao <rjliao@codeaurora.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
On some platforms the bt_en pin and susclk are default on and there
is no exposed resource to control them. This patch makes the bt_en
and susclk not mandatory to have BT work. It also will not set the
HCI_QUIRK_NON_PERSISTENT_SETUP and shutdown() callback if bt_en is
not available.
Signed-off-by: Rocky Liao <rjliao@codeaurora.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The baudrate set byte of wcn3991 in the NVM tag is byte 1, not byte 2.
This patch will set correct byte for wcn3991.
Signed-off-by: Rocky Liao <rjliao@codeaurora.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
QCA Rome doesn't support the pre-shutdown vendor hci command, this patch
will check the soc type in qca_power_off() and only send this command
for wcn399x.
Fixes: ae563183b6 ("Bluetooth: hci_qca: Enable power off/on support during hci down/up for QCA Rome")
Signed-off-by: Rocky Liao <rjliao@codeaurora.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch provides a mechanism for MGMT interface client to query the
capability of the controller to support WBS.
Signed-off-by: Alain Michaud <alainm@chromium.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This change adds a new flag to define a controller's wideband speech
capability. This is required since no reliable over HCI mechanism
exists to query the controller and driver's compatibility with
wideband speech.
Signed-off-by: Alain Michaud <alainm@chromium.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
'hu->priv' is set twice to NULL in this function.
Axe one of these assignments.
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The current codebase makes use of the zero-length array language
extension to the C90 standard, but the preferred mechanism to declare
variable-length types such as these ones is a flexible array member[1][2],
introduced in C99:
struct foo {
int stuff;
struct boo array[];
};
By making use of the mechanism above, we will get a compiler warning
in case the flexible array does not occur last in the structure, which
will help us prevent some kind of undefined behavior bugs from being
inadvertently introduced[3] to the codebase from now on.
Also, notice that, dynamic memory allocations won't be affected by
this change:
"Flexible array members have incomplete type, and so the sizeof operator
may not be applied. As a quirk of the original implementation of
zero-length arrays, sizeof evaluates to zero."[1]
This issue was found with the help of Coccinelle.
[1] https://gcc.gnu.org/onlinedocs/gcc/Zero-Length.html
[2] https://github.com/KSPP/linux/issues/21
[3] commit 7649773293 ("cxgb3/l2t: Fix undefined behaviour")
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The variable was declared in an unnecessarily broad scope.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
This patch will fix the below issues
1. Discarding memory dump events if memdump state is moved to
MEMDUMP_TIMEOUT.
2. Fixed race conditions between qca_hw_error() and qca_controller_memdump
while free memory dump buffers using mutex lock
3. Moved timeout timer to delayed work queue
4. Injecting HW error event in a case when dumps failed to receive and HW
error event is not yet received.
5. Clearing hw error and command timeout function callbacks before
sending pre shutdown command.
Collecting memory dump will follow any of the below sequence.
Sequence 1:
Receiving Memory dump events from the controller
Received entire dump in stipulated time
Received HW error event from the controller
Controller Reset from HOST
Sequence 2:
Receiving Memory dump events from the controller
Failed to Receive entire dump in stipulated time
A Timeout schedules and if no HW error event received a fake HW
error event will be injected.
Controller Reset from HOST.
Sequence 3:
Received HW error event
HOST trigger SSR by sending crash packet to controller.
Received entire dump in stipulated time
Controller Reset from HOST
Fixes: d841502c79 ("Bluetooth: hci_qca: Collect controller memory dump during SSR")
Reported-by: Abhishek Pandit-Subedi <abhishekpandit@chromium.org>
Signed-off-by: Venkata Lakshmi Narayana Gubba <gubbaven@codeaurora.org>
Reviewed-by: Abhishek Pandit-Subedi <abhishekpandit@chromium.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Add new compatible and FW loading support for RTL8822C.
Signed-off-by: Max Chou <max.chou@realtek.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Zijun Hu