Remove including <linux/version.h> that don't need it.
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Remove including <linux/version.h> that don't need it.
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
To set the duty cycle to zero (i.e. pwm_stop), the trigger value shall
be equal to the top value.
This is achieved by reading the value of the top bit field from the pwm
register and then writing back this value to the trigger and top bit
fields.
Addresses-Coverity: ("Logically dead code")
Reported-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Christer Beskow <chbe@kvaser.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Pull networking fixes from David Miller:
"Yeah I should have sent a pull request last week, so there is a lot
more here than usual:
1) Fix memory leak in ebtables compat code, from Wenwen Wang.
2) Several kTLS bug fixes from Jakub Kicinski (circular close on
disconnect etc.)
3) Force slave speed check on link state recovery in bonding 802.3ad
mode, from Thomas Falcon.
4) Clear RX descriptor bits before assigning buffers to them in
stmmac, from Jose Abreu.
5) Several missing of_node_put() calls, mostly wrt. for_each_*() OF
loops, from Nishka Dasgupta.
6) Double kfree_skb() in peak_usb can driver, from Stephane Grosjean.
7) Need to hold sock across skb->destructor invocation, from Cong
Wang.
8) IP header length needs to be validated in ipip tunnel xmit, from
Haishuang Yan.
9) Use after free in ip6 tunnel driver, also from Haishuang Yan.
10) Do not use MSI interrupts on r8169 chips before RTL8168d, from
Heiner Kallweit.
11) Upon bridge device init failure, we need to delete the local fdb.
From Nikolay Aleksandrov.
12) Handle erros from of_get_mac_address() properly in stmmac, from
Martin Blumenstingl.
13) Handle concurrent rename vs. dump in netfilter ipset, from Jozsef
Kadlecsik.
14) Setting NETIF_F_LLTX on mac80211 causes complete breakage with
some devices, so revert. From Johannes Berg.
15) Fix deadlock in rxrpc, from David Howells.
16) Fix Kconfig deps of enetc driver, we must have PHYLIB. From Yue
Haibing.
17) Fix mvpp2 crash on module removal, from Matteo Croce.
18) Fix race in genphy_update_link, from Heiner Kallweit.
19) bpf_xdp_adjust_head() stopped working with generic XDP when we
fixes generic XDP to support stacked devices properly, fix from
Jesper Dangaard Brouer.
20) Unbalanced RCU locking in rt6_update_exception_stamp_rt(), from
David Ahern.
21) Several memory leaks in new sja1105 driver, from Vladimir Oltean"
* git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (214 commits)
net: dsa: sja1105: Fix memory leak on meta state machine error path
net: dsa: sja1105: Fix memory leak on meta state machine normal path
net: dsa: sja1105: Really fix panic on unregistering PTP clock
net: dsa: sja1105: Use the LOCKEDS bit for SJA1105 E/T as well
net: dsa: sja1105: Fix broken learning with vlan_filtering disabled
net: dsa: qca8k: Add of_node_put() in qca8k_setup_mdio_bus()
net: sched: sample: allow accessing psample_group with rtnl
net: sched: police: allow accessing police->params with rtnl
net: hisilicon: Fix dma_map_single failed on arm64
net: hisilicon: fix hip04-xmit never return TX_BUSY
net: hisilicon: make hip04_tx_reclaim non-reentrant
tc-testing: updated vlan action tests with batch create/delete
net sched: update vlan action for batched events operations
net: stmmac: tc: Do not return a fragment entry
net: stmmac: Fix issues when number of Queues >= 4
net: stmmac: xgmac: Fix XGMAC selftests
be2net: disable bh with spin_lock in be_process_mcc
net: cxgb3_main: Fix a resource leak in a error path in 'init_one()'
net: ethernet: sun4i-emac: Support phy-handle property for finding PHYs
net: bridge: move default pvid init/deinit to NETDEV_REGISTER/UNREGISTER
...
Uninitialized Kernel memory can leak to USB devices.
Fix by using kzalloc() instead of kmalloc() on the affected buffers.
Signed-off-by: Tomas Bortoli <tomasbortoli@gmail.com>
Reported-by: syzbot+d6a5a1a3657b596ef132@syzkaller.appspotmail.com
Fixes: f14e22435a ("net: can: peak_usb: Do not do dma on the stack")
Cc: linux-stable <stable@vger.kernel.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Uninitialized Kernel memory can leak to USB devices.
Fix by using kzalloc() instead of kmalloc() on the affected buffers.
Signed-off-by: Tomas Bortoli <tomasbortoli@gmail.com>
Reported-by: syzbot+513e4d0985298538bf9b@syzkaller.appspotmail.com
Fixes: 0a25e1f4f1 ("can: peak_usb: add support for PEAK new CANFD USB adapters")
Cc: linux-stable <stable@vger.kernel.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
strncpy() does not ensure NULL-termination when the input string size
equals to the destination buffer size IFNAMSIZ. The output string is
passed to dev_info() which relies on the NULL-termination.
Use strlcpy() instead.
This issue is identified by a Coccinelle script.
Signed-off-by: Wang Xiayang <xywang.sjtu@sjtu.edu.cn>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
strncpy() does not ensure NULL-termination when the input string size
equals to the destination buffer size IFNAMSIZ. The output string
'name' is passed to dev_info which relies on NULL-termination.
Use strlcpy() instead.
This issue is identified by a Coccinelle script.
Signed-off-by: Wang Xiayang <xywang.sjtu@sjtu.edu.cn>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
We don't need dev_err() messages when platform_get_irq() fails now that
platform_get_irq() prints an error message itself when something goes
wrong. Let's remove these prints with a simple semantic patch.
// <smpl>
@@
expression ret;
struct platform_device *E;
@@
ret =
(
platform_get_irq(E, ...)
|
platform_get_irq_byname(E, ...)
);
if ( \( ret < 0 \| ret <= 0 \) )
{
(
-if (ret != -EPROBE_DEFER)
-{ ...
-dev_err(...);
-... }
|
...
-dev_err(...);
)
...
}
// </smpl>
While we're here, remove braces on if statements that only have one
statement (manually).
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Kalle Valo <kvalo@codeaurora.org>
Cc: Saeed Mahameed <saeedm@mellanox.com>
Cc: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Cc: Felix Fietkau <nbd@nbd.name>
Cc: Lorenzo Bianconi <lorenzo@kernel.org>
Cc: netdev@vger.kernel.org
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Stephen Boyd <swboyd@chromium.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
In preparation to enabling -Wimplicit-fallthrough, mark switch cases
where we are expecting to fall through.
This patch fixes the following warnings:
drivers/net/can/peak_canfd/peak_pciefd_main.c:668:3: warning: this statement may fall through [-Wimplicit-fallthrough=]
drivers/net/can/spi/mcp251x.c:875:7: warning: this statement may fall through [-Wimplicit-fallthrough=]
drivers/net/can/usb/peak_usb/pcan_usb.c:422:6: warning: this statement may fall through [-Wimplicit-fallthrough=]
drivers/net/can/at91_can.c:895:6: warning: this statement may fall through [-Wimplicit-fallthrough=]
drivers/net/can/at91_can.c:953:15: warning: this statement may fall through [-Wimplicit-fallthrough=]
drivers/net/can/usb/peak_usb/pcan_usb.c: In function ‘pcan_usb_decode_error’:
drivers/net/can/usb/peak_usb/pcan_usb.c:422:6: warning: this statement may fall through [-Wimplicit-fallthrough=]
if (n & PCAN_USB_ERROR_BUS_LIGHT) {
^
drivers/net/can/usb/peak_usb/pcan_usb.c:428:2: note: here
case CAN_STATE_ERROR_WARNING:
^~~~
Warning level 3 was used: -Wimplicit-fallthrough=3
This patch is part of the ongoing efforts to enabling
-Wimplicit-fallthrough.
Notice that in some cases spelling mistakes were fixed.
In other cases, the /* fall through */ comment is placed
at the bottom of the case statement, which is what GCC
is expecting to find.
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
When closing the CAN device while tx skbs are inflight, echo skb could
be released twice. By calling close_candev() before unlinking all
pending tx urbs, then the internal echo_skb[] array is fully and
correctly cleared before the USB write callback and, therefore,
can_get_echo_skb() are called, for each aborted URB.
Fixes: bb4785551f ("can: usb: PEAK-System Technik USB adapters driver core")
Signed-off-by: Stephane Grosjean <s.grosjean@peak-system.com>
Cc: linux-stable <stable@vger.kernel.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
To enter stop mode, the CPU should manually assert a global Stop Mode
request and check the acknowledgment asserted by FlexCAN. The CPU must
only consider the FlexCAN in stop mode when both request and
acknowledgment conditions are satisfied.
Fixes: de3578c198 ("can: flexcan: add self wakeup support")
Reported-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Joakim Zhang <qiangqing.zhang@nxp.com>
Cc: linux-stable <stable@vger.kernel.org> # >= v5.0
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
The gpr_np variable is still being used in dev_dbg() after the
of_node_put() call, which may result in use-after-free.
Fixes: de3578c198 ("can: flexcan: add self wakeup support")
Signed-off-by: Wen Yang <wen.yang99@zte.com.cn>
Cc: linux-stable <stable@vger.kernel.org> # >= v5.0
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
add error check when workqueue alloc failed, and remove redundant code
to make it clear.
Fixes: e0000163e3 ("can: Driver for the Microchip MCP251x SPI CAN controllers")
Signed-off-by: Weitao Hou <houweitaoo@gmail.com>
Acked-by: Willem de Bruijn <willemb@google.com>
Tested-by: Sean Nyekjaer <sean@geanix.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
We have observed rcar_canfd driver entering IRQ storm under high load,
with following scenario:
- rcar_canfd_global_interrupt() in entered due to Rx available,
- napi_schedule_prep() is called, and sets NAPIF_STATE_SCHED in state
- Rx fifo interrupts are masked,
- rcar_canfd_global_interrupt() is entered again, this time due to
error interrupt (e.g. due to overflow),
- since scheduled napi poller has not yet executed, condition for calling
napi_schedule_prep() from rcar_canfd_global_interrupt() remains true,
thus napi_schedule_prep() gets called and sets NAPIF_STATE_MISSED flag
in state,
- later, napi poller function rcar_canfd_rx_poll() gets executed, and
calls napi_complete_done(),
- due to NAPIF_STATE_MISSED flag in state, this call does not clear
NAPIF_STATE_SCHED flag from state,
- on return from napi_complete_done(), rcar_canfd_rx_poll() unmasks Rx
interrutps,
- Rx interrupt happens, rcar_canfd_global_interrupt() gets called
and calls napi_schedule_prep(),
- since NAPIF_STATE_SCHED is set in state at this time, this call
returns false,
- due to that false return, rcar_canfd_global_interrupt() returns
without masking Rx interrupt
- and this results into IRQ storm: unmasked Rx interrupt happens again
and again is misprocessed in the same way.
This patch fixes that scenario by unmasking Rx interrupts only when
napi_complete_done() returns true, which means it has cleared
NAPIF_STATE_SCHED in state.
Fixes: dd3bd23eb4 ("can: rcar_canfd: Add Renesas R-Car CAN FD driver")
Signed-off-by: Nikita Yushchenko <nikita.yoush@cogentembedded.com>
Cc: linux-stable <stable@vger.kernel.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
CONFIG_CAN_LEDS is deprecated. When trying to use the generic netdev
trigger as suggested, there's a small inconsistency with the link
property: The LED is on initially, stays on when the device is brought
up, and then turns off (as expected) when the device is brought down.
Make sure the LED always reflects the state of the CAN device.
Signed-off-by: Rasmus Villemoes <rasmus.villemoes@prevas.dk>
Acked-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
As already mentioned in [1] and included in [2], there is an off by one
issue since the high bank is already enabled when the _next_ mailbox to
be read has index 12, so the mailbox being read was 13. The message can
therefore go into mailbox 31 and the driver will be repolled until the
mailbox 12 eventually receives a msg. Or the message might end up in the
12th mailbox, but then it would become disabled after reading it and only
be enabled again in the next "round" after mailbox 13 was read, which can
cause out of order messages, since the lower priority mailboxes can
accept messages in the meantime.
As mentioned in [3] there is a hardware race condition when changing the
CANME register while messages are being received. Even when including a
busy poll on reception, like in [2] there are still overflows and out of
order messages at times, but less then without the busy loop polling.
Unlike what the patch suggests, the polling time is not in the microsecond
range, but takes as long as a current CAN bus reception needs to finish,
so typically more in the fraction of millisecond range. Since the timeout
is in jiffies it won't timeout.
Even with these additional fixes the driver is still not able to provide a
proper FIFO which doesn't drop packages. So change the driver to use
rx-offload and base order on timestamp instead of message box numbers. As
a side affect, this also fixes [4] and [5].
Before this change messages with a single byte counter were dropped /
received out of order at a bitrate of 250kbit/s on an am3517. With this
patch that no longer occurs up to and including 1Mbit/s.
[1] https://linux-can.vger.kernel.narkive.com/zgO9inVi/patch-can-ti-hecc-fix-rx-wrong-sequence-issue#post6
[2] http://arago-project.org/git/projects/?p=linux-omap3.git;a=commit;h=02346892777f07245de4d5af692513ebd852dcb2
[3] https://linux-can.vger.kernel.narkive.com/zgO9inVi/patch-can-ti-hecc-fix-rx-wrong-sequence-issue#post5
[4] https://patchwork.ozlabs.org/patch/895956/
[5] https://www.spinics.net/lists/netdev/msg494971.html
Cc: Anant Gole <anantgole@ti.com>
Cc: AnilKumar Ch <anilkumar@ti.com>
Signed-off-by: Jeroen Hofstee <jhofstee@victronenergy.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
The flexcan controller can be forced as a wakeup source by
stating that explicitly in the device's .dts file using the
"wakeup-source" boolean property.
Signed-off-by: Sean Nyekjaer <sean@geanix.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Add support to select the clock source for CAN Protocol Engine (PE).
It's SoC Implementation dependent. Refer to RM for detailed definition
of each SoC. We select clock source 1 (peripheral clock) by default in
driver now, this patch adds support to parse the clock source from the DT.
Signed-off-by: Dong Aisheng <aisheng.dong@nxp.com>
Signed-off-by: Joakim Zhang <qiangqing.zhang@nxp.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Flexcan will be disabled during suspend if no wakeup function required and
enabled after resume accordingly. During this period, we could explicitly
disable clocks.
Since PM is optional, the clock is enabled at probe to guarante the
clock is running when PM is not enabled in the kernel.
Implement Runtime PM which will:
1) Without CONFIG_PM, clock is running whether Flexcan up or down.
2) With CONFIG_PM, clock enabled while Flexcan up and disabled when
Flexcan down.
3) Disable clock when do system suspend and enable clock while system
resume.
4) Make Power Domain framework be able to shutdown the corresponding
power domain of this device.
Signed-off-by: Aisheng Dong <aisheng.dong@nxp.com>
Signed-off-by: Joakim Zhang <qiangqing.zhang@nxp.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
A statement is indented one level too deep, fix this.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Reviewed-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
CANFD IP supports both CAN and CAN FD frames,
Existing driver supports only CAN frames, This patch
adds support for CAN FD frames.
Signed-off-by: Naga Sureshkumar Relli <naga.sureshkumar.relli@xilinx.com>
Signed-off-by: Appana Durga Kedareswara rao <appana.durga.rao@xilinx.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
To differentiate between different CAN IP's this patch adds
cantype enum variable in the xcan_devtype_data structure
Signed-off-by: Appana Durga Kedareswara rao <appana.durga.rao@xilinx.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
AXI CAN IP and CANPS IP supports tx fifo empty feature, this patch updates
the flags field for the same.
Signed-off-by: Appana Durga Kedareswara rao <appana.durga.rao@xilinx.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
This patch fixes below kernel doc warnings
warning: Function parameter or member 'priv' not described in
'xcan_write_frame'
warning: Function parameter or member 'skb' not described in
'xcan_start_xmit_fifo'
warning: Function parameter or member 'ndev' not described in
'xcan_start_xmit_fifo'
warning: Function parameter or member 'skb' not described in
'xcan_start_xmit_mailbox'
warning: Function parameter or member 'ndev' not described in
'xcan_start_xmit_mailbox'
warning: Function parameter or member 'priv' not described in
'xcan_rx_fifo_get_next_frame'
Signed-off-by: Appana Durga Kedareswara rao <appana.durga.rao@xilinx.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
This patch fixes below checkpatch warnings and checks in the driver.
CHECK: Alignment should match open parenthesis
+ void (*write_reg)(const struct xcan_priv *priv, enum xcan_reg reg,
+ u32 val);
CHECK: Alignment should match open parenthesis
+static void xcan_write_reg_le(const struct xcan_priv *priv, enum xcan_reg reg,
+ u32 val)
CHECK: Alignment should match open parenthesis
+static void xcan_write_reg_be(const struct xcan_priv *priv, enum xcan_reg reg,
+ u32 val)
CHECK: Alignment should match open parenthesis
+ netdev_dbg(ndev, "BRPR=0x%08x, BTR=0x%08x\n",
+ priv->read_reg(priv, XCAN_BRPR_OFFSET),
CHECK: Alignment should match open parenthesis
+ netdev_warn(ndev,
+ "timed out for correct mode\n");
CHECK: Alignment should match open parenthesis
+ netdev_dbg(ndev, "status:#x%08x\n",
+ priv->read_reg(priv, XCAN_SR_OFFSET));
CHECK: spaces preferred around that '-' (ctx:VxV)
+ (CAN_EFF_ID_BITS-CAN_SFF_ID_BITS)) <<
^
CHECK: Alignment should match open parenthesis
+ netdev_dbg(ndev, "%s: error status register:0x%x\n",
+ __func__, priv->read_reg(priv, XCAN_ESR_OFFSET));
WARNING: line over 80 characters
+ offset = XCAN_RXMSG_2_FRAME_OFFSET(fsr & XCAN_FSR_RI_MASK);
WARNING: line over 80 characters
+ offset = XCAN_RXMSG_FRAME_OFFSET(fsr & XCAN_FSR_RI_MASK);
WARNING: line over 80 characters
+ while ((isr & XCAN_IXR_TXOK_MASK) && !WARN_ON(++retries == 100)) {
WARNING: line over 80 characters
+ priv->write_reg(priv, XCAN_ICR_OFFSET, XCAN_IXR_TXOK_MASK);
CHECK: Alignment should match open parenthesis
+ netdev_err(ndev, "%s: pm_runtime_get failed(%d)\n",
+ __func__, ret);
CHECK: Alignment should match open parenthesis
+ ret = request_irq(ndev->irq, xcan_interrupt, priv->irq_flags,
+ ndev->name, ndev);
CHECK: Alignment should match open parenthesis
+static int xcan_get_berr_counter(const struct net_device *ndev,
+ struct can_berr_counter *bec)
CHECK: Alignment should match open parenthesis
+ netdev_err(ndev, "%s: pm_runtime_get failed(%d)\n",
+ __func__, ret);
CHECK: Please don't use multiple blank lines
+
+
CHECK: Alignment should match open parenthesis
+ netdev_err(ndev, "%s: pm_runtime_get failed(%d)\n",
+ __func__, ret);`
Signed-off-by: Appana Durga Kedareswara rao <appana.durga.rao@xilinx.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Add the TCAN4x5x SPI CAN driver.
This device uses the Bosch MCAN IP core along with a SPI interface map.
Register to the MCAN common core code to manage the MCAN IP.
This device has a special method to indicate a write/read operation on
the data payload.
Acked-by: Wolfgang Grandegger <wg@grandegger.com>
Signed-off-by: Dan Murphy <dmurphy@ti.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Rename the common m_can_priv class structure to m_can_classdev as this
is more descriptive.
Acked-by: Wolfgang Grandegger <wg@grandegger.com>
Signed-off-by: Dan Murphy <dmurphy@ti.com>
Acked-by: Faiz Abbas <faiz_abbas@ti.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Create a m_can platform framework that peripheral
devices can register to and use common code and register sets.
The peripheral devices may provide read/write and configuration
support of the IP.
Acked-by: Wolfgang Grandegger <wg@grandegger.com>
Signed-off-by: Dan Murphy <dmurphy@ti.com>
Acked-by: Faiz Abbas <faiz_abbas@ti.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
In preparation to enabling -Wimplicit-fallthrough, mark switch cases
where we are expecting to fall through.
This patch fixes the following warnings:
drivers/net/can/peak_canfd/peak_pciefd_main.c:668:3: warning: this statement may fall through [-Wimplicit-fallthrough=]
drivers/net/can/spi/mcp251x.c:875:7: warning: this statement may fall through [-Wimplicit-fallthrough=]
drivers/net/can/usb/peak_usb/pcan_usb.c:422:6: warning: this statement may fall through [-Wimplicit-fallthrough=]
drivers/net/can/at91_can.c:895:6: warning: this statement may fall through [-Wimplicit-fallthrough=]
drivers/net/can/at91_can.c:953:15: warning: this statement may fall through [-Wimplicit-fallthrough=]
drivers/net/can/usb/peak_usb/pcan_usb.c: In function ‘pcan_usb_decode_error’:
drivers/net/can/usb/peak_usb/pcan_usb.c:422:6: warning: this statement may fall through [-Wimplicit-fallthrough=]
if (n & PCAN_USB_ERROR_BUS_LIGHT) {
^
drivers/net/can/usb/peak_usb/pcan_usb.c:428:2: note: here
case CAN_STATE_ERROR_WARNING:
^~~~
Warning level 3 was used: -Wimplicit-fallthrough=3
This patch is part of the ongoing efforts to enabling
-Wimplicit-fallthrough.
Notice that in some cases spelling mistakes were fixed.
In other cases, the /* fall through */ comment is placed
at the bottom of the case statement, which is what GCC
is expecting to find.
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com> # for the at91_can.c
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
This patch adds support for Kvaser PCIEcan devices. This includes
support for up to 4 CAN channels on a single card, depending on device.
Signed-off-by: Henning Colliander <henning.colliander@evidente.se>
Signed-off-by: Jimmy Assarsson <extja@kvaser.com>
Signed-off-by: Christer Beskow <chbe@kvaser.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
One of the more common cases of allocation size calculations is finding
the size of a structure that has a zero-sized array at the end, along
with memory for some number of elements for that array. For example:
struct foo {
int stuff;
void *entry[];
};
instance = alloc(sizeof(struct foo) + count * sizeof(void *));
Instead of leaving these open-coded and prone to type mistakes, we can
now use the new struct_size() helper:
instance = alloc(struct_size(instance, entry, count));
This code was detected with the help of Coccinelle.
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
This patch add support for Fintek PCIE to 2 CAN controller support
Signed-off-by: Ji-Ze Hong (Peter Hong) <hpeter+linux_kernel@gmail.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
This patch sorts the drivers in the Makefile alphabetically and arranges
the Kconfig file accordingly.
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Several drivers cast a struct device pointer to a struct
platform_device pointer only to then call platform_get_drvdata().
To improve readability, these constructs can be simplified
by using dev_get_drvdata() directly.
Signed-off-by: Fuqian Huang <huangfq.daxian@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Another round of SPDX updates for 5.2-rc6
Here is what I am guessing is going to be the last "big" SPDX update for
5.2. It contains all of the remaining GPLv2 and GPLv2+ updates that
were "easy" to determine by pattern matching. The ones after this are
going to be a bit more difficult and the people on the spdx list will be
discussing them on a case-by-case basis now.
Another 5000+ files are fixed up, so our overall totals are:
Files checked: 64545
Files with SPDX: 45529
Compared to the 5.1 kernel which was:
Files checked: 63848
Files with SPDX: 22576
This is a huge improvement.
Also, we deleted another 20000 lines of boilerplate license crud, always
nice to see in a diffstat.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCXQyQYA8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ymnGQCghETUBotn1p3hTjY56VEs6dGzpHMAnRT0m+lv
kbsjBGEJpLbMRB2krnaU
=RMcT
-----END PGP SIGNATURE-----
Merge tag 'spdx-5.2-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/spdx
Pull still more SPDX updates from Greg KH:
"Another round of SPDX updates for 5.2-rc6
Here is what I am guessing is going to be the last "big" SPDX update
for 5.2. It contains all of the remaining GPLv2 and GPLv2+ updates
that were "easy" to determine by pattern matching. The ones after this
are going to be a bit more difficult and the people on the spdx list
will be discussing them on a case-by-case basis now.
Another 5000+ files are fixed up, so our overall totals are:
Files checked: 64545
Files with SPDX: 45529
Compared to the 5.1 kernel which was:
Files checked: 63848
Files with SPDX: 22576
This is a huge improvement.
Also, we deleted another 20000 lines of boilerplate license crud,
always nice to see in a diffstat"
* tag 'spdx-5.2-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/spdx: (65 commits)
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 507
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 506
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 505
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 504
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 503
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 502
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 501
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 500
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 499
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 498
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 497
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 496
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 495
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 491
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 490
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 489
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 488
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 487
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 486
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 485
...
Based on 2 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license version 2 as
published by the free software foundation
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license version 2 as
published by the free software foundation #
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference in 4122 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Enrico Weigelt <info@metux.net>
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Allison Randal <allison@lohutok.net>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190604081206.933168790@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Based on 1 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the version 2 of the gnu general public
license as published by the free software foundation this program is
distributed in the hope that it will be useful but without any
warranty without even the implied warranty of merchantability or
fitness for a particular purpose see the gnu general public license
for more details
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference in 10 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Allison Randal <allison@lohutok.net>
Reviewed-by: Enrico Weigelt <info@metux.net>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190604081206.259525894@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Pull networking fixes from David Miller:
"Lots of bug fixes here:
1) Out of bounds access in __bpf_skc_lookup, from Lorenz Bauer.
2) Fix rate reporting in cfg80211_calculate_bitrate_he(), from John
Crispin.
3) Use after free in psock backlog workqueue, from John Fastabend.
4) Fix source port matching in fdb peer flow rule of mlx5, from Raed
Salem.
5) Use atomic_inc_not_zero() in fl6_sock_lookup(), from Eric Dumazet.
6) Network header needs to be set for packet redirect in nfp, from
John Hurley.
7) Fix udp zerocopy refcnt, from Willem de Bruijn.
8) Don't assume linear buffers in vxlan and geneve error handlers,
from Stefano Brivio.
9) Fix TOS matching in mlxsw, from Jiri Pirko.
10) More SCTP cookie memory leak fixes, from Neil Horman.
11) Fix VLAN filtering in rtl8366, from Linus Walluij.
12) Various TCP SACK payload size and fragmentation memory limit fixes
from Eric Dumazet.
13) Use after free in pneigh_get_next(), also from Eric Dumazet.
14) LAPB control block leak fix from Jeremy Sowden"
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (145 commits)
lapb: fixed leak of control-blocks.
tipc: purge deferredq list for each grp member in tipc_group_delete
ax25: fix inconsistent lock state in ax25_destroy_timer
neigh: fix use-after-free read in pneigh_get_next
tcp: fix compile error if !CONFIG_SYSCTL
hv_sock: Suppress bogus "may be used uninitialized" warnings
be2net: Fix number of Rx queues used for flow hashing
net: handle 802.1P vlan 0 packets properly
tcp: enforce tcp_min_snd_mss in tcp_mtu_probing()
tcp: add tcp_min_snd_mss sysctl
tcp: tcp_fragment() should apply sane memory limits
tcp: limit payload size of sacked skbs
Revert "net: phylink: set the autoneg state in phylink_phy_change"
bpf: fix nested bpf tracepoints with per-cpu data
bpf: Fix out of bounds memory access in bpf_sk_storage
vsock/virtio: set SOCK_DONE on peer shutdown
net: dsa: rtl8366: Fix up VLAN filtering
net: phylink: set the autoneg state in phylink_phy_change
net: add high_order_alloc_disable sysctl/static key
tcp: add tcp_tx_skb_cache sysctl
...
Currently the following message is observed when the flexcan
driver is probed:
flexcan 2090000.flexcan: device registered (reg_base=(ptrval), irq=23)
The reason for printing 'ptrval' is explained at
Documentation/core-api/printk-formats.rst:
"Pointers printed without a specifier extension (i.e unadorned %p) are
hashed to prevent leaking information about the kernel memory layout. This
has the added benefit of providing a unique identifier. On 64-bit machines
the first 32 bits are zeroed. The kernel will print ``(ptrval)`` until it
gathers enough entropy."
Instead of passing %pK, which can print the correct address, simply
remove the entire message as it is not really that useful.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
During frame reception while the MCAN is in Error Passive state and the
Receive Error Counter has thevalue MCAN_ECR.REC = 127, it may happen
that MCAN_IR.MRAF is set although there was no Message RAM access
failure. If MCAN_IR.MRAF is enabled, an interrupt to the Host CPU is
generated.
Work around:
The Message RAM Access Failure interrupt routine needs to check whether
MCAN_ECR.RP = '1' and MCAN_ECR.REC = '127'.
In this case, reset MCAN_IR.MRAF. No further action is required.
This affects versions older than 3.2.0
Errata explained on Sama5d2 SoC which includes this hardware block:
http://ww1.microchip.com/downloads/en/DeviceDoc/SAMA5D2-Family-Silicon-Errata-and-Data-Sheet-Clarification-DS80000803B.pdf
chapter 6.2
Reproducibility: If 2 devices with m_can are connected back to back,
configuring different bitrate on them will lead to interrupt storm on
the receiving side, with error "Message RAM access failure occurred".
Another way is to have a bad hardware connection. Bad wire connection
can lead to this issue as well.
This patch fixes the issue according to provided workaround.
Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
Reviewed-by: Ludovic Desroches <ludovic.desroches@microchip.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Fully compatible with mcp2515, the mcp25625 have integrated transceiver.
This patch adds support for the mcp25625 to the existing mcp251x driver.
Signed-off-by: Sean Nyekjaer <sean@geanix.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Commit 9e5f1b273e ("can: xilinx_can: add support for Xilinx CAN FD
core") added a new can_bittiming_const structure for CAN FD cores that
support larger values for tseg1, tseg2, and sjw than previous Xilinx CAN
cores, but the commit did not actually take that into use.
Fix that.
Tested with CAN FD core on a ZynqMP board.
Fixes: 9e5f1b273e ("can: xilinx_can: add support for Xilinx CAN FD core")
Reported-by: Shubhrajyoti Datta <shubhrajyoti.datta@gmail.com>
Signed-off-by: Anssi Hannula <anssi.hannula@bitwise.fi>
Cc: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Shubhrajyoti Datta <shubhrajyoti.datta@gmail.com>
Cc: linux-stable <stable@vger.kernel.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Current we can meet timeout issue when setting a small bitrate like
10000 as follows on i.MX6UL EVK board (ipg clock = 66MHZ, per clock =
30MHZ):
| root@imx6ul7d:~# ip link set can0 up type can bitrate 10000
A link change request failed with some changes committed already.
Interface can0 may have been left with an inconsistent configuration,
please check.
| RTNETLINK answers: Connection timed out
It is caused by calling of flexcan_chip_unfreeze() timeout.
Originally the code is using usleep_range(10, 20) for unfreeze
operation, but the patch (8badd65 can: flexcan: avoid calling
usleep_range from interrupt context) changed it into udelay(10) which is
only a half delay of before, there're also some other delay changes.
After double to FLEXCAN_TIMEOUT_US to 100 can fix the issue.
Meanwhile, Rasmus Villemoes reported that even with a timeout of 100,
flexcan_probe() fails on the MPC8309, which requires a value of at least
140 to work reliably. 250 works for everyone.
Signed-off-by: Joakim Zhang <qiangqing.zhang@nxp.com>
Reviewed-by: Dong Aisheng <aisheng.dong@nxp.com>
Cc: linux-stable <stable@vger.kernel.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
This seems to have slipped in by accident when sorting the entries.
Fixes: ffbdd9172e
Signed-off-by: Alexander Dahl <ada@thorsis.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Based on 1 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license as published by
the free software foundation version 2 of the license this program
is distributed in the hope that it will be useful but without any
warranty without even the implied warranty of merchantability or
fitness for a particular purpose see the gnu general public license
for more details you should have received a copy of the gnu general
public license along with this program
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference in 2 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Allison Randal <allison@lohutok.net>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190531190112.858563475@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Based on 1 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the version 2 of the gnu general public
license as published by the free software foundation this program is
distributed in the hope that it will be useful but without any
warranty without even the implied warranty of merchantability or
fitness for a particular purpose see the gnu general public license
for more details you should have received a copy of the gnu general
public license along with this program if not see http www gnu org
licenses
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference in 15 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Allison Randal <allison@lohutok.net>
Reviewed-by: Alexios Zavras <alexios.zavras@intel.com>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190530000437.427740574@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Based on 1 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license as published by
the free software foundation version 2 of the license this program
is distributed in the hope that it will be useful but without any
warranty without even the implied warranty of merchantability or
fitness for a particular purpose see the gnu general public license
for more details you should have received a copy of the gnu general
public license along with this program if not see http www gnu org
licenses
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference in 15 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Alexios Zavras <alexios.zavras@intel.com>
Reviewed-by: Richard Fontana <rfontana@redhat.com>
Reviewed-by: Allison Randal <allison@lohutok.net>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190530000437.052642892@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Based on 1 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license as published by
the free software foundation version 2 of the license this program
is distributed in the hope that it will be useful but without any
warranty without even the implied warranty of merchantability or
fitness for a particular purpose see the gnu general public license
for more details
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference in 100 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Alexios Zavras <alexios.zavras@intel.com>
Reviewed-by: Allison Randal <allison@lohutok.net>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190529141900.918357685@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Based on 1 normalized pattern(s):
this software may be distributed under the terms of the gnu general
public license gpl version 2 as distributed in the copying file from
the main directory of the linux kernel source
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference in 1 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Alexios Zavras <alexios.zavras@intel.com>
Reviewed-by: Steve Winslow <swinslow@gmail.com>
Reviewed-by: Allison Randal <allison@lohutok.net>
Reviewed-by: Richard Fontana <rfontana@redhat.com>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190528170027.816396794@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Based on 1 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license as published by
the free software foundation version 2 of the license this program
is distributed in the hope that it will be useful but without any
warranty without even the implied warranty of merchantability or
fitness for a particular purpose see the gnu general public license
for more details you should have received a copy of the gnu general
public license along with this program if not write to the free
software foundation inc 51 franklin street fifth floor boston ma
02110 1301 usa
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference in 12 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Richard Fontana <rfontana@redhat.com>
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Allison Randal <allison@lohutok.net>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190527070033.745497013@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Based on 3 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license as published by
the free software foundation either version 2 of the license or at
your option any later version this program is distributed in the
hope that it will be useful but without any warranty without even
the implied warranty of merchantability or fitness for a particular
purpose see the gnu general public license for more details
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license as published by
the free software foundation either version 2 of the license or at
your option any later version [author] [kishon] [vijay] [abraham]
[i] [kishon]@[ti] [com] this program is distributed in the hope that
it will be useful but without any warranty without even the implied
warranty of merchantability or fitness for a particular purpose see
the gnu general public license for more details
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license as published by
the free software foundation either version 2 of the license or at
your option any later version [author] [graeme] [gregory]
[gg]@[slimlogic] [co] [uk] [author] [kishon] [vijay] [abraham] [i]
[kishon]@[ti] [com] [based] [on] [twl6030]_[usb] [c] [author] [hema]
[hk] [hemahk]@[ti] [com] this program is distributed in the hope
that it will be useful but without any warranty without even the
implied warranty of merchantability or fitness for a particular
purpose see the gnu general public license for more details
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-or-later
has been chosen to replace the boilerplate/reference in 1105 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Allison Randal <allison@lohutok.net>
Reviewed-by: Richard Fontana <rfontana@redhat.com>
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190527070033.202006027@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Based on 1 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license as published by
the free software foundation either version 2 of the license or at
your option any later version
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-or-later
has been chosen to replace the boilerplate/reference in 3029 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Allison Randal <allison@lohutok.net>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190527070032.746973796@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Based on 2 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license as published by
the free software foundation either version 2 of the license or at
your option any later version this program is distributed in the
hope that it will be useful but without any warranty without even
the implied warranty of merchantability or fitness for a particular
purpose see the gnu general public license for more details you
should have received a copy of the gnu general public license along
with this program if not see http www gnu org licenses
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license as published by
the free software foundation either version 2 of the license or at
your option any later version this program is distributed in the
hope that it will be useful but without any warranty without even
the implied warranty of merchantability or fitness for a particular
purpose see the gnu general public license for more details [based]
[from] [clk] [highbank] [c] you should have received a copy of the
gnu general public license along with this program if not see http
www gnu org licenses
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-or-later
has been chosen to replace the boilerplate/reference in 355 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Jilayne Lovejoy <opensource@jilayne.com>
Reviewed-by: Steve Winslow <swinslow@gmail.com>
Reviewed-by: Allison Randal <allison@lohutok.net>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190519154041.837383322@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add SPDX license identifiers to all Make/Kconfig files which:
- Have no license information of any form
These files fall under the project license, GPL v2 only. The resulting SPDX
license identifier is:
GPL-2.0-only
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Clang points out undefined behavior when building the pcan_usb_pro driver:
drivers/net/can/usb/peak_usb/pcan_usb_pro.c:136:15: error: passing an object that undergoes default argument promotion to 'va_start' has undefined behavior [-Werror,-Wvarargs]
Changing the function prototype to avoid argument promotion in the
varargs call avoids the warning, and should make this well-defined.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Nathan Chancellor <natechancellor@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit cbffaf7aa0 ("can: flexcan: Always use last mailbox for TX")
introduced a loop letting i run up to (including) ARRAY_SIZE(regs->mb)
and in the body accessed regs->mb[i] which is an out-of-bounds array
access that then resulted in an access to an reserved register area.
Later this was changed by commit 0517961ccd ("can: flexcan: Add
provision for variable payload size") to iterate a bit differently but
still runs one iteration too much resulting to call
flexcan_get_mb(priv, priv->mb_count)
which results in a WARN_ON and then a NULL pointer exception. This
only affects devices compatible with "fsl,p1010-flexcan",
"fsl,imx53-flexcan", "fsl,imx35-flexcan", "fsl,imx25-flexcan",
"fsl,imx28-flexcan", so newer i.MX SoCs are not affected.
Fixes: cbffaf7aa0 ("can: flexcan: Always use last mailbox for TX")
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Cc: linux-stable <stable@vger.kernel.org> # >= 4.20
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
This patch revert commit 7da11ba5c5
("can: dev: __can_get_echo_skb(): print error message, if trying to echo non existing skb")
After introduction of this change we encountered following new error
message on various i.MX plattforms (flexcan):
| flexcan 53fc8000.can can0: __can_get_echo_skb: BUG! Trying to echo non
| existing skb: can_priv::echo_skb[0]
The introduction of the message was a mistake because
priv->echo_skb[idx] = NULL is a perfectly valid in following case: If
CAN_RAW_LOOPBACK is disabled (setsockopt) in applications, the pkt_type
of the tx skb's given to can_put_echo_skb is set to PACKET_LOOPBACK. In
this case can_put_echo_skb will not set priv->echo_skb[idx]. It is
therefore kept NULL.
As additional argument for revert: The order of check and usage of idx
was changed. idx is used to access an array element before checking it's
boundaries.
Signed-off-by: Manfred Schlaegl <manfred.schlaegl@ginzinger.com>
Fixes: 7da11ba5c5 ("can: dev: __can_get_echo_skb(): print error message, if trying to echo non existing skb")
Cc: linux-stable <stable@vger.kernel.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
The message buffer RAM area is not a contiguous 1KB area but 2 partitions
of 512 bytes each. Till now, we used Message buffers with payload size 8
bytes, which translates to 32 MBs per partition and no spare space is left
in any partition.
However, in upcoming SOC LX2160A the message buffers can have payload size
64 bytes. This results in less than 32 MBs per partition and some empty
area is left at the end of each partition.This empty area should not be
accessed.
Therefore, split the Message Buffer RAM area into two partitions.
Signed-off-by: Pankaj Bansal <pankaj.bansal@nxp.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Till now the flexcan module supported 8 byte payload size as per CAN 2.0
specifications. But now upcoming flexcan module in NXP LX2160A SOC
supports CAN FD protocol too. The Message buffers need to be configured
to have payload size 64 bytes.
Therefore, added provision in the driver for payload size to be 64 bytes.
Signed-off-by: Pankaj Bansal <pankaj.bansal@nxp.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
rx offload depends on number of message buffers, which in turn depends
on messgae buffer size. with the upcoming LX2160A SOC the message buffer
size can be configured to 72 bytes if it were to be used in CAN FD mode.
The current mode in which the flexcan is being operated is known at the
time of flexcan_open() but not at the time of flexcan_probe().
Therefore, move the rx_offload_add() from flexcan_probe() to
flexcan_open(). correspondingly, move rx_offload_delete() from
flexcan_remove() to flexcan_close().
Signed-off-by: Pankaj Bansal <pankaj.bansal@nxp.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Self reception disable bit needs to be cleared for loopback mode to work
in flexcan.
Signed-off-by: Pankaj Bansal <pankaj.bansal@nxp.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
If wakeup is enabled, enter stop mode, else enter disabled mode. Self wake
can only work on stop mode.
Starting from IMX6, the flexcan stop mode control bits is SoC specific,
move it out of IP driver and parse it from devicetree.
Signed-off-by: Aisheng Dong <aisheng.dong@nxp.com>
Signed-off-by: Joakim Zhang <qiangqing.zhang@nxp.com>
Reviewed-by: Dong Aisheng <aisheng.dong@nxp.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
With the conversion of the flexcan driver to support both timestamp and
FIFO mode the setup of the MCR register ("enable fifo") has been moved.
This patch moves the comment too, in order to match the code again.
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
This patch fixes the following checkpatch warning:
| Macro argument 'x' may be better as '(x)' to avoid precedence issues
Fixes: cbffaf7aa0 ("can: flexcan: Always use last mailbox for TX")
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
The patch fixes the indention by replacing space by tabs, as noted by
checkpatch:
| ERROR: code indent should use tabs where possible
| #980: FILE: drivers/net/can/flexcan.c:980:
Fixes: da49a8075c ("can: flexcan: implement error passive state quirk")
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
This patch fixes the indentio nin flexcan_start_xmit() by alligning the
code to the opening parenthesis.
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
flexcan is an IP module independent of the SOC architecture.
Therefore, enable it for all architectures.
Signed-off-by: Pankaj Bansal <pankaj.bansal@nxp.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
This patch adds SPDX-License-Identifier to Kconfig and Makefile.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Acked-by: Ramesh Shanmugasundaram <ramesh.shanmugasundaram@bp.renesas.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Adopt the SPDX license identifier headers to ease license compliance
management.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
This patch adds support for ASEM opto-isolated dual channels
CAN raw device (http://www.asem.it)
Signed-off-by: Flavio Suligoi <f.suligoi@asem.it>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
The method ndo_start_xmit() is defined as returning an 'netdev_tx_t',
which is a typedef for an enum type, so make sure the implementation in
this driver has returns 'netdev_tx_t' value, and change the function
return type to netdev_tx_t.
Found by coccinelle.
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Trivial fix to spelling mistake in netdev_dbg error message
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Currently, in case of bus error, driver will generate error message and put
in the tail of the message queue. To avoid confusions, this change should
place the bus related messages in proper order.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Cc: linux-stable <stable@vger.kernel.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
This function has nothing todo with error.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Cc: linux-stable <stable@vger.kernel.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Current flexcan driver will put TX-ECHO in regular unsorted way, in
this case TX-ECHO can come after the response to the same TXed message.
In some cases, for example for J1939 stack, things will break.
This patch is using new rx-offload API to put the messages just in the
right place.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Cc: linux-stable <stable@vger.kernel.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Current CAN framework can't guarantee proper/chronological order
of RX and TX-ECHO messages. To make this possible, drivers should use
this functions instead of can_get_echo_skb().
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Cc: linux-stable <stable@vger.kernel.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Prior to echoing a successfully transmitted CAN frame (by calling
can_get_echo_skb()), CAN drivers have to put the CAN frame (by calling
can_put_echo_skb() in the transmit function). These put and get function
take an index as parameter, which is used to identify the CAN frame.
A driver calling can_get_echo_skb() with a index not pointing to a skb
is a BUG, so add an appropriate error message.
Cc: linux-stable <stable@vger.kernel.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
If the "struct can_priv::echo_skb" is accessed out of bounds would lead
to a kernel crash. Better print a sensible warning message instead and
try to recover.
Cc: linux-stable <stable@vger.kernel.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
This patch replaces the use of "struct can_frame::can_dlc" by "struct
canfd_frame::len" to access the frame's length. As it is ensured that
both structures have a compatible memory layout for this member this is
no functional change. Futher, this compatibility is documented in a
comment.
Cc: linux-stable <stable@vger.kernel.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
This patch factors out all non sending parts of can_get_echo_skb() into
a seperate function __can_get_echo_skb(), so that it can be re-used in
an upcoming patch.
Cc: linux-stable <stable@vger.kernel.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
The previous patch changes the TX path to always use the last mailbox
regardless of the used offload scheme (rx-fifo or timestamp based). This
means members "tx_mb" and "tx_mb_idx" of the struct flexcan_priv don't
depend on the offload scheme, so replace them by compile time constants.
Cc: linux-stable <stable@vger.kernel.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Essentially this patch moves the TX mailbox to position 63, regardless
of timestamp based offloading or RX FIFO. So mainly the iflag register
usage regarding TX has changed. The rest is consolidating RX FIFO and
timestamp offloading as they now use both the same TX mailbox.
The reason is a very annoying behavior regarding sending RTR frames when
_not_ using RX FIFO:
If a TX mailbox sent a RTR frame it becomes a RX mailbox. For that
reason flexcan_irq disables the TX mailbox again. But if during the time
the RTR was sent and the TX mailbox is disabled a new CAN frames is
received, it is lost without notice. The reason is that so-called
"Move-in" process starts from the lowest mailbox which happen to be a TX
mailbox set to EMPTY.
Steps to reproduce (I used an imx7d):
1. generate regular bursts of messages
2. send a RTR from flexcan with higher priority than burst messages every
1ms, e.g. cangen -I 0x100 -L 0 -g 1 -R can0
3. notice a lost message without notification after some seconds
When running an iperf in parallel this problem is occurring even more
frequently. Using filters is not possible as at least one single CAN-ID
is allowed. Handling the TX MB during RX is also not possible as there
is no race-free disable of RX MB.
There is still a slight window when the described problem can occur. But
for that all RX MB must be in use which is essentially next to an
overrun. Still there will be no indication if it ever occurs.
Signed-off-by: Alexander Stein <alexander.stein@systec-electronic.com>
Cc: linux-stable <stable@vger.kernel.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Unlock the MB irrespective of reception method being FIFO or timestamp
based. It is optional but recommended to unlock Mailbox as soon as
possible and make it available for reception.
Reported-by: Alexander Stein <alexander.stein@systec-electronic.com>
Signed-off-by: Pankaj Bansal <pankaj.bansal@nxp.com>
Cc: linux-stable <stable@vger.kernel.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
If the hi3110 shares the SPI bus with another traffic-intensive device
and packets are received in high volume (by a separate machine sending
with "cangen -g 0 -i -x"), reception stops after a few minutes and the
counter in /proc/interrupts stops incrementing. Bus state is "active".
Bringing the interface down and back up reconvenes the reception. The
issue is not observed when the hi3110 is the sole device on the SPI bus.
Using a level-triggered interrupt makes the issue go away and lets the
hi3110 successfully receive 2 GByte over the course of 5 days while a
ks8851 Ethernet chip on the same SPI bus handles 6 GByte of traffic.
Unfortunately the hi3110 datasheet is mum on the trigger type. The pin
description on page 3 only specifies the polarity (active high):
http://www.holtic.com/documents/371-hi-3110_v-rev-kpdf.do
Cc: Mathias Duckeck <m.duckeck@kunbus.de>
Cc: Akshay Bhat <akshay.bhat@timesys.com>
Cc: Casey Fitzpatrick <casey.fitzpatrick@timesys.com>
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Cc: linux-stable <stable@vger.kernel.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Assigning 2 to "renesas,can-clock-select" tricks the driver into
registering the CAN interface, even though we don't want that.
This patch improves one of the checks to prevent that from happening.
Fixes: 862e2b6af9 ("can: rcar_can: support all input clocks")
Signed-off-by: Fabrizio Castro <fabrizio.castro@bp.renesas.com>
Signed-off-by: Chris Paterson <Chris.Paterson2@renesas.com>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Fixes gcc '-Wunused-but-set-variable' warning:
drivers/net/can/usb/ucan.c: In function 'ucan_disconnect':
drivers/net/can/usb/ucan.c:1578:21: warning:
variable 'udev' set but not used [-Wunused-but-set-variable]
struct usb_device *udev;
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Reviewed-by: Martin Elshuber <martin.elshuber@theobroma-systems.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
The call to can_put_echo_skb() may result in the skb being freed. The skb
is later used in the call to dev->ops->dev_frame_to_cmd().
This is avoided by moving the call to can_put_echo_skb() after
dev->ops->dev_frame_to_cmd().
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Jimmy Assarsson <jimmyassarsson@gmail.com>
Cc: linux-stable <stable@vger.kernel.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
If alloc_can_err_skb() fails, cf is never initialized.
Move assignment of cf inside check.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Jimmy Assarsson <jimmyassarsson@gmail.com>
Cc: linux-stable <stable@vger.kernel.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Add extack arg to rtnl_create_link and add messages for invalid
number of Tx or Rx queues.
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Eliminate code which assumes that SKBs and skb_queue_head objects
can be cast to eachother during list processing.
Signed-off-by: David S. Miller <davem@davemloft.net>
Marc Kleine-Budde