If create_regulator() fails in set_supply(), the module refcount
needs be put to keep refcount balanced.
Fixes: e2c09ae7a7 ("regulator: core: Increase refcount for regulator supply's module")
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Link: https://lore.kernel.org/r/20221201122706.4055992-2-yangyingliang@huawei.com
Signed-off-by: Mark Brown <broonie@kernel.org>
I found a use_count leakage towards supply regulator of rdev with
boot-on option.
┌───────────────────┐ ┌───────────────────┐
│ regulator_dev A │ │ regulator_dev B │
│ (boot-on) │ │ (boot-on) │
│ use_count=0 │◀──supply──│ use_count=1 │
│ │ │ │
└───────────────────┘ └───────────────────┘
In case of rdev(A) configured with `regulator-boot-on', the use_count
of supplying regulator(B) will increment inside
regulator_enable(rdev->supply).
Thus, B will acts like always-on, and further balanced
regulator_enable/disable cannot actually disable it anymore.
However, B was also configured with `regulator-boot-on', we wish it
could be disabled afterwards.
Signed-off-by: Rui Zhang <zr.zhang@vivo.com>
Link: https://lore.kernel.org/r/20221201033806.2567812-1-zr.zhang@vivo.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Use kfree_const() to free supply_name conditionally in create_regulator()
as supply_name may be allocated from kmalloc() or directly from .rodata
section.
Fixes: 87fe29b61f ("regulator: push allocations in create_regulator() outside of lock")
Signed-off-by: Wang ShaoBo <bobo.shaobowang@huawei.com>
Link: https://lore.kernel.org/r/20221123034616.3609537-1-bobo.shaobowang@huawei.com
Signed-off-by: Mark Brown <broonie@kernel.org>
I got the the following report:
OF: ERROR: memory leak, expected refcount 1 instead of 2,
of_node_get()/of_node_put() unbalanced - destroy cset entry:
attach overlay node /i2c/pmic@62/regulators/exten
In of_get_regulator(), the node is returned from of_parse_phandle()
with refcount incremented, after using it, of_node_put() need be called.
Fixes: 69511a452e ("regulator: map consumer regulator based on device tree")
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Link: https://lore.kernel.org/r/20221115091508.900752-1-yangyingliang@huawei.com
Signed-off-by: Mark Brown <broonie@kernel.org>
We had an exclusive variant of the devm_regulator_get() API, but no
corresponding variant for the bulk API; let's add one now. We add a
generalized version of the existing regulator_bulk_get() function that
additionally takes a get_type parameter and redefine
regulator_bulk_get() in terms of it, then do similarly with
devm_regulator_bulk_get(), and finally add the new
devm_regulator_bulk_get_exclusive().
Signed-off-by: Zev Weiss <zev@bewilderbeest.net>
Link: https://lore.kernel.org/r/20221031233704.22575-2-zev@bewilderbeest.net
Signed-off-by: Mark Brown <broonie@kernel.org>
The core work this time around has mostly been around the code to manage
regulator modes, simplifying the interface for configuring modes to not
take account of the voltage and as a side effect resolving a
bootstrapping issue on systems where we can't read the voltage from the
regulator. Otherwise it's been quite a quiet release with some new
drivers and a devm helper:
- Make the load handling in the Qualcomm RPMH regulators much more
idiomatic and general cleanups to the handling of load configuration.
- devm helper for a combined get and enable operation.
- Support for MediaTek MT6331, Qualcomm PM660, 660L and PM6125, Texas
Instruments TPS65219.
-----BEGIN PGP SIGNATURE-----
iQEzBAABCgAdFiEEreZoqmdXGLWf4p/qJNaLcl1Uh9AFAmM61ZQACgkQJNaLcl1U
h9BGggf+MraXhaTOSrLCzKYjcsjIZ2OCzySoKPdh9PdvnKc2PX+vIi6SYjq6zeAe
OlwDvKzW+bR6VRTStSskK5wRXrLn/9eo25GhZyl4BpAR+vjGBtzlNagk3gGTBKMj
ua/kb16FV+15Zg5L1qO35ka9BuCzs2Bfz9OoZKy4vtuqVqazmrU3PS8nr/kAlW9R
fi7a50Ybc+W7xBYUNuaKqdFQWlblLh/UKqImV9dANokXZDD9deJ8BeWq/FttNY6T
lyTJGDuKYhcvb7wx8QdzcSCoLsdVPRi0cmIlbjiusWogyvJBQVhto338Y8+b7vIJ
29tlD54gmWXSxwf0e8CpHKh/BxwbAw==
=YFsi
-----END PGP SIGNATURE-----
Merge tag 'regulator-v6.1' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator
Pull regulator updates from Mark Brown:
"The core work this time around has mostly been around the code to
manage regulator modes, simplifying the interface for configuring
modes to not take account of the voltage and as a side effect
resolving a bootstrapping issue on systems where we can't read the
voltage from the regulator.
Otherwise it's been quite a quiet release with some new drivers and a
devm helper:
- Make the load handling in the Qualcomm RPMH regulators much more
idiomatic and general cleanups to the handling of load
configuration
- devm helper for a combined get and enable operation
- Support for MediaTek MT6331, Qualcomm PM660, 660L and PM6125, Texas
Instruments TPS65219"
* tag 'regulator-v6.1' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator: (45 commits)
dt-bindings: gpio-regulator: add vin-supply property support
regulator: gpio: Add input_supply support in gpio_regulator_config
regulator: tps65219: Fix is_enabled checking in tps65219_set_bypass
regulator: qcom,rpmh: add pm660 and pm660l pmics
regulator: qcom-rpmh: add pm660 and pm660l pmics
regulator: of: Fix kernel-doc
regulator: of: Fix kernel-doc
regulator: Add driver for MT6332 PMIC regulators
regulator: Add bindings for MT6332 regulator
regulator: Add driver for MT6331 PMIC regulators
regulator: Add bindings for MT6331 regulator
regulator: tps65219: Fix .bypass_val_on setting
regulator: qcom_rpm: Fix circular deferral regression
regulator: core: Prevent integer underflow
regulator: dt-bindings: qcom,rpmh: Indicate regulator-allow-set-load dependencies
regulator: bd9576: switch to using devm_fwnode_gpiod_get()
regulator: bd71815: switch to using devm_fwnode_gpiod_get()
regulator: core: Fix regulator supply registration with sysfs
regulator: tps65219: change tps65219_regulator_irq_types to static
regulator: core: Don't err if allow-set-load but no allowed-modes
...
By using a ratio of delay to poll_enabled_time that is not integer
time_remaining underflows and does not exit the loop as expected.
As delay could be derived from DT and poll_enabled_time is defined
in the driver this can easily happen.
Use a signed iterator to make sure that the loop exits once
the remaining time is negative.
Signed-off-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Link: https://lore.kernel.org/r/20220909125954.577669-1-patrick.rudolph@9elements.com
Signed-off-by: Mark Brown <broonie@kernel.org>
One core fix here improving the error handling on enable failure, plus
smaller fixes for the pfuze100 drive and the SPMI DT bindings.
-----BEGIN PGP SIGNATURE-----
iQEzBAABCgAdFiEEreZoqmdXGLWf4p/qJNaLcl1Uh9AFAmMZ3IUACgkQJNaLcl1U
h9CwbQf6AzcfEH0QTrQrkJV5m0lWfpxSdmxWg2NSmKDsCUTEg4KKV86+iGbOax1y
StciVjWKBQ7nTwX7d2tWYL67ogziN4ePFdroKzIHMkj50+qWfy1KsopsWgm6joYj
YCfWro3f2LHD7CC70qsd1yoVV4mO+yzdwkc0qtxQe4l9rvsdfA8VH80MjGyWaxUO
dz8BjLAk3ivCsCTCGFkL3k51HLm7ORbX8ruCqFnW3a6neblliIP/z+MkNhLgZC7q
+P3GGbBYYs1d9Ay5IIM04FszhJEOfG7RSeqMosi6gCl2r8Vw3UNJ7rUyH/cGTwyV
eZFTgd89kiVg1I97FxbI4Wb1SjPg0A==
=97j3
-----END PGP SIGNATURE-----
Merge tag 'regulator-fix-v6.0-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator
Pull regulator fixes from Mark Brown:
"One core fix here improving the error handling on enable failure, plus
smaller fixes for the pfuze100 drive and the SPMI DT bindings"
* tag 'regulator-fix-v6.0-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator:
regulator: Fix qcom,spmi-regulator schema
regulator: pfuze100: Fix the global-out-of-bounds access in pfuze100_regulator_probe()
regulator: core: Clean up on enable failure
In "regulator: core: Resolve supply name earlier to prevent
double-init", we introduced a bug that prevented the regulator names
from registering properly with sysfs.
Reorder regulator_register such that supply names are properly resolved
and registered.
Fixes: 8a866d527a ("regulator: core: Resolve supply name earlier to prevent double-init")
Link: https://lore.kernel.org/all/58b92e75-f373-dae7-7031-8abd465bb874@samsung.com/
Signed-off-by: Christian Kohlschütter <christian@kohlschutter.com>
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Link: https://lore.kernel.org/r/20220829165543.24856-1-christian@kohlschutter.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Apparently the device trees of some boards have the property
"regulator-allow-set-load" for some of their regulators but then they
don't specify anything for "regulator-allowed-modes". That's not
really legit, but...
...before commit efb0cb50c4 ("regulator: qcom-rpmh: Implement
get_optimum_mode(), not set_load()") they used to get away with it, at
least on boards using RPMH regulators. That's because when a regulator
driver implements set_load() then the core doesn't look at
"regulator-allowed-modes" when trying to automatically adjust things
in response to the regulator's load. The core doesn't know what mode
we'll end up in, so how could it validate it?
Said another way: before commit efb0cb50c4 ("regulator: qcom-rpmh:
Implement get_optimum_mode(), not set_load()") some boards _were_
having the regulator mode adjusted despite listing no allowed
modes. After commit efb0cb50c4 ("regulator: qcom-rpmh: Implement
get_optimum_mode(), not set_load()") these same boards were now
getting an error returned when trying to use their regulators, since
simply enabling a regulator tries to update its load and that was
failing.
We don't really want to go back to the behavior from before commit
efb0cb50c4 ("regulator: qcom-rpmh: Implement get_optimum_mode(), not
set_load()"). Boards shouldn't have been changing modes if no allowed
modes were listed. However, the behavior after commit efb0cb50c4
("regulator: qcom-rpmh: Implement get_optimum_mode(), not set_load()")
isn't the best because now boards can't even turn their regulators on.
Let's choose to detect this case and return "no error" from
drms_uA_update(). The net-result will be _different_ behavior than we
had before commit efb0cb50c4 ("regulator: qcom-rpmh: Implement
get_optimum_mode(), not set_load()"), but this new behavior seems more
correct. If a board truly needed the mode switched then its device
tree should be updated to list the allowed modes.
Reported-by: Andrew Halaney <ahalaney@redhat.com>
Fixes: efb0cb50c4 ("regulator: qcom-rpmh: Implement get_optimum_mode(), not set_load()")
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Tested-by: Andrew Halaney <ahalaney@redhat.com>
Link: https://lore.kernel.org/r/20220824142229.RFT.v2.2.I6f77860e5cd98bf5c67208fa9edda4a08847c304@changeid
Signed-off-by: Mark Brown <broonie@kernel.org>
The get_optimum_mode() for regulator drivers is passed the input
voltage and output voltage as well as the current. This is because, in
theory, the optimum mode can depend on all three things.
It turns out that for all regulator drivers in mainline only the
current is looked at when implementing get_optimum_mode(). None of the
drivers take the input or output voltage into account. Despite the
fact that none of the drivers take the input or output voltage into
account, though, the regulator framework will error out before calling
into get_optimum_mode() if it doesn't know the input or output
voltage.
The above behavior turned out to be a probelm for some boards when we
landed commit efb0cb50c4 ("regulator: qcom-rpmh: Implement
get_optimum_mode(), not set_load()"). Before that change we'd have no
problems running drms_uA_update() for RPMH regulators even if a
regulator's input or output voltage was unknown. After that change
drms_uA_update() started to fail. This is because typically boards
using RPMH regulators don't model the input supplies of RPMH
regulators. Input supplies for RPMH regulators nearly always come from
the output of other RPMH regulators (or always-on regulators) and RPMH
firmware is initialized with this knowledge and handles enabling (and
adjusting the voltage of) input supplies. While we could model the
parent/child relationship of the regulators in Linux, many boards
don't bother since it adds extra overhead.
Let's change the regulator core to make things work again. Now if we
fail to get the input or output voltage we'll still call into
get_optimum_mode() and we'll just pass error codes in for input_uV
and/or output_uV parameters.
Since no existing regulator drivers even look at input_uV and
output_uV we don't need to add this error handling anywhere right
now. We'll add some comments in the core so that it's obvious that (if
regulator drivers care) it's up to them to add the checks.
Reported-by: Andrew Halaney <ahalaney@redhat.com>
Fixes: efb0cb50c4 ("regulator: qcom-rpmh: Implement get_optimum_mode(), not set_load()")
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Tested-by: Andrew Halaney <ahalaney@redhat.com>
Link: https://lore.kernel.org/r/20220824142229.RFT.v2.1.I137e6bef4f6d517be7b081be926059321102fd3d@changeid
Signed-off-by: Mark Brown <broonie@kernel.org>
If regulator_enable() fails, enable_count is incremented still.
A consumer, assuming no matching regulator_disable() is necessary on
failure, will then get this error message upon regulator_put()
since enable_count is non-zero:
[ 1.277418] WARNING: CPU: 3 PID: 1 at drivers/regulator/core.c:2304 _regulator_put.part.0+0x168/0x170
The consumer could try to fix this in their driver by cleaning up on
error from regulator_enable() (i.e. call regulator_disable()), but that
results in the following since regulator_enable() failed and didn't
increment user_count:
[ 1.258112] unbalanced disables for vreg_l17c
[ 1.262606] WARNING: CPU: 4 PID: 1 at drivers/regulator/core.c:2899 _regulator_disable+0xd4/0x190
Fix this by decrementing enable_count upon failure to enable.
With this in place, just the reason for failure to enable is printed
as expected and developers can focus on the root cause of their issue
instead of thinking their usage of the regulator consumer api is
incorrect. For example, in my case:
[ 1.240426] vreg_l17c: invalid input voltage found
Fixes: 5451781dad ("regulator: core: Only count load for enabled consumers")
Signed-off-by: Andrew Halaney <ahalaney@redhat.com>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Brian Masney <bmasney@redhat.com>
Link: https://lore.kernel.org/r/20220819194336.382740-1-ahalaney@redhat.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Previously, an unresolved regulator supply reference upon calling
regulator_register on an always-on or boot-on regulator caused
set_machine_constraints to be called twice.
This in turn may initialize the regulator twice, leading to voltage
glitches that are timing-dependent. A simple, unrelated configuration
change may be enough to hide this problem, only to be surfaced by
chance.
One such example is the SD-Card voltage regulator in a NanoPI R4S that
would not initialize reliably unless the registration flow was just
complex enough to allow the regulator to properly reset between calls.
Fix this by re-arranging regulator_register, trying resolve the
regulator's supply early enough that set_machine_constraints does not
need to be called twice.
Signed-off-by: Christian Kohlschütter <christian@kohlschutter.com>
Link: https://lore.kernel.org/r/20220818124646.6005-1-christian@kohlschutter.com
Signed-off-by: Mark Brown <broonie@kernel.org>
In commit 6eabfc018e ("regulator: core: Allow specifying an initial
load w/ the bulk API") I changed the error handling but had a subtle
that caused us to always return no error even if there was an
error. Fix it.
Fixes: 6eabfc018e ("regulator: core: Allow specifying an initial load w/ the bulk API")
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Link: https://lore.kernel.org/r/20220809142738.1.I91625242f137c707bb345c51c80c5ecee02eeff3@changeid
Signed-off-by: Mark Brown <broonie@kernel.org>
Merge series from Douglas Anderson <dianders@chromium.org>:
The main goal of this series is to make a small dent in cleaning up
the way we deal with regulator loads. The idea is to add some extra
functionality to the regulator "bulk" API so that consumers can
specify the load using that.
There are a number of drivers that follow a pattern that looks like
this:
1. Use the regulator bulk API to get a bunch of regulators.
2. Set the load on each of the regulators to use whenever the
regulators are enabled.
Let's make this easier by just allowing the drivers to pass the load
in.
As part of this change we need to move the error printing in
regulator_bulk_get() around; let's switch to the new dev_err_probe()
to simplify it.
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Link: https://lore.kernel.org/r/20220726103631.v2.4.Ie85f68215ada39f502a96dcb8a1f3ad977e3f68a@changeid
Signed-off-by: Mark Brown <broonie@kernel.org>
Regulators marked with "regulator-always-on" or "regulator-boot-on"
as well as an "off-on-delay-us", may run into cycling issues that are
hard to detect.
This is caused by the "last_off" state not being initialized in this
case.
Fix the "last_off" initialization by setting it to the current kernel
time upon initialization, regardless of always_on/boot_on state.
Signed-off-by: Christian Kohlschütter <christian@kohlschutter.com>
Link: https://lore.kernel.org/r/FAFD5B39-E9C4-47C7-ACF1-2A04CD59758D@kohlschutter.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Since the introduction of regulator->enable_count, a driver that did
an exclusive get on an already-enabled regulator would end up with
enable_count initialized to 0 but rdev->use_count initialized to 1.
With that starting point the regulator is effectively stuck enabled,
because if the driver attempted to disable it it would fail the
enable_count underflow check in _regulator_handle_consumer_disable().
The EXCLUSIVE_GET path in _regulator_get() now initializes
enable_count along with rdev->use_count so that the regulator can be
disabled without underflowing the former.
Signed-off-by: Zev Weiss <zev@bewilderbeest.net>
Fixes: 5451781dad ("regulator: core: Only count load for enabled consumers")
Link: https://lore.kernel.org/r/20220505043152.12933-1-zev@bewilderbeest.net
Signed-off-by: Mark Brown <broonie@kernel.org>
If a regulator provides a get_error_flags() operation, its sysfs
attributes will now include an entry for each defined
REGULATOR_ERROR_* flag.
Signed-off-by: Zev Weiss <zev@bewilderbeest.net>
Link: https://lore.kernel.org/r/20220504065252.6955-3-zev@bewilderbeest.net
Signed-off-by: Mark Brown <broonie@kernel.org>
These delays can be relatively large (e.g., hundreds of microseconds to
several milliseconds on RK3399 Gru systems). Per
Documentation/timers/timers-howto.rst, that should usually use a
sleeping delay. Let's use the existing regulator delay helper to handle
both large and small delays appropriately. This avoids burning a bunch
of CPU time and hurting scheduling latencies when hitting regulators a
lot (e.g., during cpufreq).
The sleep vs. delay issue choice has been made differently over time --
early versions of RK3399 Gru PWM-regulator support used usleep_range()
in pwm-regulator.c. More of this got moved into the regulator core,
in commits like:
73e705bf81 regulator: core: Add set_voltage_time op
At the same time, the sleep turned into a delay.
It's OK to sleep in _regulator_do_set_voltage(), as we aren't in an
atomic context. (All our callers grab various mutexes already.)
I avoid using fsleep() because it uses a usleep_range() of [N to N*2],
and usleep_range() very commonly biases to the high end of the range. We
don't want to double the expected delay, especially for long delays.
Signed-off-by: Brian Norris <briannorris@chromium.org>
Reviewed-by: Matthias Kaehlcke <mka@chromium.org>
Link: https://lore.kernel.org/r/20220420141511.v2.2.If0fc61a894f537b052ca41572aff098cf8e7e673@changeid
Signed-off-by: Mark Brown <broonie@kernel.org>
While we currently assume that regulators with no control available are
just uncontionally enabled this isn't always as clearly displayed to
users as is desirable, for example the code for disabling unused
regulators will log that it is about to disable them. Clean this up a
bit by setting always_on during constraint evaluation if we have no
available mechanism for controlling the regualtor so things that check
the constraint will do the right thing.
Signed-off-by: Mark Brown <broonie@kernel.org>
Link: https://lore.kernel.org/r/20220325144637.1543496-1-broonie@kernel.org
Signed-off-by: Mark Brown <broonie@kernel.org>
The check done by regulator_late_cleanup() to detect whether a regulator
is on was inconsistent with the check done by _regulator_is_enabled().
While _regulator_is_enabled() takes the enable GPIO into account,
regulator_late_cleanup() was not doing that.
This resulted in a false positive, e.g. when a GPIO-controlled fixed
regulator was used, which was not enabled at boot time, e.g.
reg_disp_1v2: reg_disp_1v2 {
compatible = "regulator-fixed";
regulator-name = "display_1v2";
regulator-min-microvolt = <1200000>;
regulator-max-microvolt = <1200000>;
gpio = <&tlmm 148 0>;
enable-active-high;
};
Such regulator doesn't have an is_enabled() operation. Nevertheless
it's state can be determined based on the enable GPIO. The check in
regulator_late_cleanup() wrongly assumed that the regulator is on and
tried to disable it.
Signed-off-by: Oliver Barta <oliver.barta@aptiv.com>
Link: https://lore.kernel.org/r/20220208084645.8686-1-oliver.barta@aptiv.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Thanks to the removal of the unused TPS80021 driver the regulator
updates for this cycle actually have a negative diffstat. Otherwise
it's been quite a quiet release, lots of fixes and small improvements
with the biggest individual changes being several conversions of DT
bindings to YAML format.
-----BEGIN PGP SIGNATURE-----
iQEzBAABCgAdFiEEreZoqmdXGLWf4p/qJNaLcl1Uh9AFAmF//M0ACgkQJNaLcl1U
h9ByVQf/QapSey1s8ifh7Or3oiG7Ak6BdPYxiPIzhZIqjz4gXV8ySn8EedbH7moW
NcKpqokZ4qPD32fcET2WFQLb9tA8BNEQS1VwRKG+uhzPi3xBnIVj0gt8lNOAW57g
cUWeJhIbafaym33zB0xdDAukLHqjnx24C33Fz8QWaaQv/xRhaCrbzhala4WfXXyP
ucyOqSNnHZ+KX0tQsIG05b9jqca+VrNAyefY5jum2l2r2LFfGjQDv6g0HJEKfcF3
PSu+1RBFsYA3sPvzqzdtcuEs7hqalXVNGBfogCzNQ1HhK9z48R4J9lHtswDDk4EA
9aLYiid02UYRpRpT34z2TexpufW9kQ==
=5lYk
-----END PGP SIGNATURE-----
Merge tag 'regulator-v5.16' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator
Pull regulator updates from Mark Brown:
"Thanks to the removal of the unused TPS80021 driver the regulator
updates for this cycle actually have a negative diffstat.
Otherwise it's been quite a quiet release, lots of fixes and small
improvements with the biggest individual changes being several
conversions of DT bindings to YAML format"
* tag 'regulator-v5.16' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator: (34 commits)
regulator: Don't error out fixed regulator in regulator_sync_voltage()
regulator: tps80031: Remove driver
regulator: Fix SY7636A breakage
regulator: uniphier: Add binding for NX1 SoC
regulator: uniphier: Add USB-VBUS compatible string for NX1 SoC
regulator: qcom,rpmh: Add compatible for PM6350
regulator: qcom-rpmh: Add PM6350 regulators
regulator: sy7636a: Remove requirement on sy7636a mfd
regulator: tps62360: replacing legacy gpio interface for gpiod
regulator: lp872x: Remove lp872x_dvs_state
regulator: lp872x: replacing legacy gpio interface for gpiod
regulator: dt-bindings: samsung,s5m8767: convert to dtschema
regulator: dt-bindings: samsung,s2mpa01: convert to dtschema
regulator: dt-bindings: samsung,s2m: convert to dtschema
dt-bindings: clock: samsung,s2mps11: convert to dtschema
regulator: dt-bindings: samsung,s5m8767: correct s5m8767,pmic-buck-default-dvs-idx property
regulator: s5m8767: do not use reset value as DVS voltage if GPIO DVS is disabled
regulator: dt-bindings: maxim,max8973: convert to dtschema
regulator: dt-bindings: maxim,max8997: convert to dtschema
regulator: dt-bindings: maxim,max8952: convert to dtschema
...
Fixed regulator can't change voltage and regulator_sync_voltage()
returns -EINVAL in this case. Make regulator_sync_voltage() to succeed
for regulators that are incapable to change voltage.
On NVIDIA Tegra power management driver needs to sync voltage and we have
one device (Trimslice) that uses fixed regulator which is getting synced.
The syncing error isn't treated as fatal, but produces a noisy error
message. This patch silences that error.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Link: https://lore.kernel.org/r/20211021183308.27786-1-digetx@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
We lowered all the other constraint related log messages to debug level so
lower the logging of what supplies we're configuring to debug level too.
Signed-off-by: Mark Brown <broonie@kernel.org>
Link: https://lore.kernel.org/r/20210929140717.3769-1-broonie@kernel.org
Signed-off-by: Mark Brown <broonie@kernel.org>
i915 will soon gain an eviction path that trylock a whole lot of locks
for eviction, getting dmesg failures like below:
BUG: MAX_LOCK_DEPTH too low!
turning off the locking correctness validator.
depth: 48 max: 48!
48 locks held by i915_selftest/5776:
#0: ffff888101a79240 (&dev->mutex){....}-{3:3}, at: __driver_attach+0x88/0x160
#1: ffffc900009778c0 (reservation_ww_class_acquire){+.+.}-{0:0}, at: i915_vma_pin.constprop.63+0x39/0x1b0 [i915]
#2: ffff88800cf74de8 (reservation_ww_class_mutex){+.+.}-{3:3}, at: i915_vma_pin.constprop.63+0x5f/0x1b0 [i915]
#3: ffff88810c7f9e38 (&vm->mutex/1){+.+.}-{3:3}, at: i915_vma_pin_ww+0x1c4/0x9d0 [i915]
#4: ffff88810bad5768 (reservation_ww_class_mutex){+.+.}-{3:3}, at: i915_gem_evict_something+0x110/0x860 [i915]
#5: ffff88810bad60e8 (reservation_ww_class_mutex){+.+.}-{3:3}, at: i915_gem_evict_something+0x110/0x860 [i915]
...
#46: ffff88811964d768 (reservation_ww_class_mutex){+.+.}-{3:3}, at: i915_gem_evict_something+0x110/0x860 [i915]
#47: ffff88811964e0e8 (reservation_ww_class_mutex){+.+.}-{3:3}, at: i915_gem_evict_something+0x110/0x860 [i915]
INFO: lockdep is turned off.
Fixing eviction to nest into ww_class_acquire is a high priority, but
it requires a rework of the entire driver, which can only be done one
step at a time.
As an intermediate solution, add an acquire context to
ww_mutex_trylock, which allows us to do proper nesting annotations on
the trylocks, making the above lockdep splat disappear.
This is also useful in regulator_lock_nested, which may avoid dropping
regulator_nesting_mutex in the uncontended path, so use it there.
TTM may be another user for this, where we could lock a buffer in a
fastpath with list locks held, without dropping all locks we hold.
[peterz: rework actual ww_mutex_trylock() implementations]
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Link: https://lkml.kernel.org/r/YUBGPdDDjKlxAuXJ@hirez.programming.kicks-ass.net
Voltage-controlled regulators depend on their supply regulator for
retrieving their voltage, and so they might return -EPROBE_DEFER at this
stage. Our caller already attempts to resolve supplies and retry, so we
shouldn't be printing this error to logs.
Quiets log messages like this, on Rockchip RK3399 Gru/Kevin boards:
[ 1.033057] ppvar_bigcpu: failed to get the current voltage: -EPROBE_DEFER
...
[ 1.036735] ppvar_litcpu: failed to get the current voltage: -EPROBE_DEFER
...
[ 1.040366] ppvar_gpu: failed to get the current voltage: -EPROBE_DEFER
...
[ 1.044086] ppvar_centerlogic: failed to get the current voltage: -EPROBE_DEFER
Cc: Chen-Yu Tsai <wenst@chromium.org>
Signed-off-by: Brian Norris <briannorris@chromium.org>
Link: https://lore.kernel.org/r/20210826124015.1.Iab79c6dd374ec48beac44be2fcddd165dd26476b@changeid
Signed-off-by: Mark Brown <broonie@kernel.org>
Extend regulator notification support
This series extends the regulator notification and error flag support.
Initial discussion on the topic can be found here:
https://lore.kernel.org/lkml/6046836e22b8252983f08d5621c35ececb97820d.camel@fi.rohmeurope.com/
In a nutshell - the series adds:
1. WARNING level events/error flags. (Patch 3)
Current regulator 'ERROR' event notifications for over/under
voltage, over current and over temperature are used to indicate
condition where monitored entity is so badly "off" that it actually
indicates a hardware error which can not be recovered. The most
typical hanling for that is believed to be a (graceful)
system-shutdown. Here we add set of 'WARNING' level flags to allow
sending notifications to consumers before things are 'that badly off'
so that consumer drivers can implement recovery-actions.
2. Device-tree properties for specifying limit values. (Patches 1, 5)
Add limits for above mentioned 'ERROR' and 'WARNING' levels (which
send notifications to consumers) and also for a 'PROTECTION' level
(which will be used to immediately shut-down the regulator(s) W/O
informing consumer drivers. Typically implemented by hardware).
Property parsing is implemented in regulator core which then calls
callback operations for limit setting from the IC drivers. A
warning is emitted if protection is requested by device tree but the
underlying IC does not support configuring requested protection.
3. Helpers which can be registered by IC. (Patch 4)
Target is to avoid implementing IRQ handling and IRQ storm protection
in each IC driver. (Many of the ICs implementin these IRQs do not allow
masking or acking the IRQ but keep the IRQ asserted for the whole
duration of problem keeping the processor in IRQ handling loop).
4. Emergency poweroff function (refactored out of the thermal_core to
kernel/reboot.c) which is called if IC fires error IRQs but IC reading
fails and given retry-count is exceeded. (Patches 2, 4)
Please note that the mutex in the emergency shutdown was replaced by a
simple atomic in order to allow call from any context.
The helper was attempted to be done so it could be used to implement
roughly same logic as is used in qcom-labibb regulator. This means
amongst other things a safety shut-down if IC registers are not readable.
Using these shut-down retry counters are optional. The idea is that the
helper could be also used by simpler ICs which do not provide status
register(s) which can be used to check if error is still active.
ICs which do not have such status register can simply omit the 'renable'
callback (and retry-counts etc) - and helper assumes the situation is Ok
and re-enables IRQ after given time period. If problem persists the
handler is ran again and another notification is sent - but at least the
delay allows processor to avoid IRQ loop.
Patch 7 takes this notification support in use at BD9576MUF.
Patch 8 is related to MFD change which is not really related to the RFC
here. It was added to this series in order to avoid potential conflicts.
Patch 9 adds a maintainers entry.
Changelog v10-RESEND:
- rebased on v5.13-rc4
Changelog v10:
- rebased on v5.13-rc2
- Move rdev_*() print macros to the internal.h and use rdev_dbg()
from irq_helpers.c
- Export rdev_get_name() and move it from coupler.h to driver.h for
others to use. (It was already in coupler.h but not exported -
usage was limited and coupler.h does not sound like optimal place
as rdev_name is not only used by coupled regulators)
- Send all regulator notifications from irq_helpers.c at one OR'd
event for the sake of simplicity. For BD9576 this does not matter
as it has own IRQ for each event case. Header defining events says
they may be OR'd.
- Change WARN() at protection shutdown to pr_emerg as suggested by
Petr.
Changelog v9:
- rebases on v5.13-rc1
- Update thermal documentation
- Fix regulator notification event number
Changelog v8:
- split shutdown API adding and thermal core taking it in use to
own patches.
- replace the spinlock with atomic when ensuring the emergency
shutdown is only called once.
Changelog v7:
general:
- rebased on v5.12-rc7
- new patch for refactoring the hw-failure reboot logic out of
thermal_core.c for others to use.
notification helpers:
- fix regulator error_flags query
- grammar/typos
- do not BUG() but attempt to shut-down the system
- use BITS_PER_TYPE()
Changelog v6:
Add MAINTAINERS entry
Changes to IRQ notifiers
- move devm functions to drivers/regulator/devres.c
- drop irq validity check
- use devm_add_action_or_reset()
- fix styling issues
- fix kerneldocs
Changelog v5:
- Fix the badly formatted pr_emerg() call.
Changelog v4:
- rebased on v5.12-rc6
- dropped RFC
- fix external FET DT-binding.
- improve prints for cases when expecting HW failure.
- styling and typos
Changelog v3:
Regulator core:
- Fix dangling pointer access at regulator_irq_helper()
stpmic1_regulator:
- fix function prototype (compile error)
bd9576-regulator:
- Update over current limits to what was given in new data-sheet
(REV00K)
- Allow over-current monitoring without external FET. Set limits to
values given in data-sheet (REV00K).
Changelog v2:
Generic:
- rebase on v5.12-rc2 + BD9576 series
- Split devm variant of delayed wq to own series
Regulator framework:
- Provide non devm variant of IRQ notification helpers
- shorten dt-property names as suggested by Rob
- unconditionally call map_event in IRQ handling and require it to be
populated
BD9576 regulators:
- change the FET resistance property to micro-ohms
- fix voltage computation in OC limit setting
Provide helper function for IC's implementing regulator notifications
when an IRQ fires. The helper also works for IRQs which can not be acked.
Helper can be set to disable the IRQ at handler and then re-enabling it
on delayed work later. The helper also adds regulator_get_error_flags()
errors in cache for the duration of IRQ disabling.
Signed-off-by: Matti Vaittinen <matti.vaittinen@fi.rohmeurope.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Link: https://lore.kernel.org/r/ebdf86d8c22b924667ec2385330e30fcbfac0119.1622628334.git.matti.vaittinen@fi.rohmeurope.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The rdev print helpers are a nice way to print messages related to a
specific regulator device. Move them from core.c to internal.h
As the rdev print helpers use rdev_get_name() export it from core.c. Also
move the declaration from coupler.h to driver.h because the rdev name is
not just a coupled regulator property. I guess the main audience for
rdev_get_name() will be the regulator core and drivers.
Signed-off-by: Matti Vaittinen <matti.vaittinen@fi.rohmeurope.com>
Link: https://lore.kernel.org/r/dc7fd70dc31de4d0e820b7646bb78eeb04f80735.1622628333.git.matti.vaittinen@fi.rohmeurope.com
Signed-off-by: Mark Brown <broonie@kernel.org>
This adds regulator_sync_voltage_rdev(), which is used as a dependency
for new Tegra power domain code.
-----BEGIN PGP SIGNATURE-----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=/dXp
-----END PGP SIGNATURE-----
gpgsig -----BEGIN PGP SIGNATURE-----
iQEzBAABCgAdFiEEreZoqmdXGLWf4p/qJNaLcl1Uh9AFAmDHMi0ACgkQJNaLcl1U
h9Dbvgf/dAcS9d9lgjijzGYcvsh3hBpWqimMrO/dfXlalqXfdU0VN82++0WIcpC7
uoQ2I6RwU4NNTvMUjbmyQsYONMBNthxYEgGDdtwOE03TLVJHc9KyKCzRLFp0E0sX
wHvoAbSZbzd1OIC+96iWJzeC9rq24LX5IaP8301hWKFhbZpo3/uP9yTgQuxSp0cf
tuQDu8vzW7TuC7pxy06FgCmVhsEd2OXEO+wu9OWzMoIAh2Z82KlEb8j0cpV0G0d1
jPdDanaFwJ3LZevbMXZQnJyCGRhFU74vboSC3Vb8e2H7eCwb68s3Z5mo1Dxq6M3o
qE9JGQRgVVOHr67vYXfirOzmhz2D5g==
=5rP3
-----END PGP SIGNATURE-----
Merge tag 'for-5.14-regulator' of git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux into regulator-5.14
regulator: Changes for v5.14-rc1
This adds regulator_sync_voltage_rdev(), which is used as a dependency
for new Tegra power domain code.
Use DEVICE_ATTR_RO() helper instead of plain DEVICE_ATTR(),
which makes the code a bit shorter and easier to read.
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Link: https://lore.kernel.org/r/20210529115226.25376-1-yuehaibing@huawei.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Some NVIDIA Tegra devices use a CPU soft-reset method for the reboot and
in this case we need to restore the coupled voltages to the state that is
suitable for hardware during boot. Add new regulator_sync_voltage_rdev()
helper which is needed by regulator drivers in order to sync voltage of
a coupled regulators.
Acked-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
For the boot-on/always-on regulators the set_machine_constrainst() is
called before resolving rdev->supply. Thus the code would try to enable
rdev before enabling supplying regulator. Enforce resolving supply
regulator before enabling rdev.
Fixes: aea6cb9970 ("regulator: resolve supply after creating regulator")
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20210519221224.2868496-1-dmitry.baryshkov@linaro.org
Signed-off-by: Mark Brown <broonie@kernel.org>
The jiffies-based off_on_delay implementation has a couple of problems
that cause it to sometimes not actually delay for the required time:
(1) If, for example, the off_on_delay time is equivalent to one jiffy,
and the ->last_off_jiffy is set just before a new jiffy starts,
then _regulator_do_enable() does not wait at all since it checks
using time_before().
(2) When jiffies overflows, the value of "remaining" becomes higher
than "max_delay" and the code simply proceeds without waiting.
Fix these problems by changing it to use ktime_t instead.
[Note that since jiffies doesn't start at zero but at INITIAL_JIFFIES
("-5 minutes"), (2) above also led to the code not delaying if
the first regulator_enable() is called when the ->last_off_jiffy is not
initialised, such as for regulators with ->constraints->boot_on set.
It's not clear to me if this was intended or not, but I've preserved
this behaviour explicitly with the check for a non-zero ->last_off.]
Signed-off-by: Vincent Whitchurch <vincent.whitchurch@axis.com>
Link: https://lore.kernel.org/r/20210423114524.26414-1-vincent.whitchurch@axis.com
Signed-off-by: Mark Brown <broonie@kernel.org>
We currently do not respect off_on_delay the first time we turn on a
regulator. This is problematic since the regulator could have been
turned off by the bootloader, or it could it have been turned off during
the probe of the regulator driver (such as when regulator-fixed requests
the enable GPIO), either of which could potentially have happened less
than off_on_delay microseconds ago before the first time a client
requests for the regulator to be turned on.
We can't know exactly when the regulator was turned off, but initialise
off_on_delay to the current time when registering the regulator, so that
we guarantee that we respect the off_on_delay in all cases.
Signed-off-by: Vincent Whitchurch <vincent.whitchurch@axis.com>
Link: https://lore.kernel.org/r/20210422083044.11479-1-vincent.whitchurch@axis.com
Signed-off-by: Mark Brown <broonie@kernel.org>
s/regulator may on/regulator may already be enabled/
s/or left on/or was left on/
The aim of this patch is to make the comment more readable and to make
it clear, that this is about a regulator, that is already enabled instead
of a regulator that may be switched on.
Signed-off-by: Sebastian Fricke <sebastian.fricke@posteo.net>
Link: https://lore.kernel.org/r/20210421055236.13148-1-sebastian.fricke@posteo.net
Signed-off-by: Mark Brown <broonie@kernel.org>
Sometimes regulator_get() gets called twice for the same supply on the
same device. This may happen e.g. when a framework / library is used
which uses the regulator; and the driver itself also needs to enable
the regulator in some cases where the framework will not enable it.
Commit ff268b56ce ("regulator: core: Don't spew backtraces on
duplicate sysfs") already takes care of the backtrace which would
trigger when creating a duplicate consumer symlink under
/sys/class/regulator/regulator.%d in this scenario.
Commit c33d442328 ("debugfs: make error message a bit more verbose")
causes a new error to get logged in this scenario:
[ 26.938425] debugfs: Directory 'wm5102-codec-MICVDD' with parent 'spi-WM510204:00-MICVDD' already present!
There is no _nowarn variant of debugfs_create_dir(), but we can detect
and avoid this problem by checking the return value of the earlier
sysfs_create_link_nowarn() call.
Add a check for the earlier sysfs_create_link_nowarn() failing with
-EEXIST and skip the debugfs_create_dir() call in that case, avoiding
this error getting logged.
Fixes: c33d442328 ("debugfs: make error message a bit more verbose")
Cc: Charles Keepax <ckeepax@opensource.cirrus.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20210122183250.370571-1-hdegoede@redhat.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Make regulator_sync_voltage() to re-balance voltage state of a coupled
regulators instead of changing the voltage directly.
Tested-by: Peter Geis <pgwipeout@gmail.com> # Ouya T30
Tested-by: Dmitry Osipenko <digetx@gmail.com> # A500 T20 and Nexus7 T30
Tested-by: Nicolas Chauvet <kwizart@gmail.com> # PAZ00 T20
Tested-by: Matt Merhar <mattmerhar@protonmail.com> # Ouya T30
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Link: https://lore.kernel.org/r/20210122174311.28230-1-digetx@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
With commit eaa7995c52 (regulator: core: avoid
regulator_resolve_supply() race condition) we started holding the rdev
lock while resolving supplies, an operation that requires holding the
regulator_list_mutex. This results in lockdep warnings since in other
places we take the list mutex then the mutex on an individual rdev.
Since the goal is to make sure that we don't call set_supply() twice
rather than a concern about the cost of resolution pull the rdev lock
and check for duplicate resolution down to immediately before we do the
set_supply() and drop it again once the allocation is done.
Fixes: eaa7995c52 (regulator: core: avoid regulator_resolve_supply() race condition)
Reported-by: Marek Szyprowski <m.szyprowski@samsung.com>
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Link: https://lore.kernel.org/r/20210122132042.10306-1-broonie@kernel.org
Signed-off-by: Mark Brown <broonie@kernel.org>
The final step in regulator_register() is to call
regulator_resolve_supply() for each registered regulator
(including the one in the process of being registered). The
regulator_resolve_supply() function first checks if rdev->supply
is NULL, then it performs various steps to try to find the supply.
If successful, rdev->supply is set inside of set_supply().
This procedure can encounter a race condition if two concurrent
tasks call regulator_register() near to each other on separate CPUs
and one of the regulators has rdev->supply_name specified. There
is currently nothing guaranteeing atomicity between the rdev->supply
check and set steps. Thus, both tasks can observe rdev->supply==NULL
in their regulator_resolve_supply() calls. This then results in
both creating a struct regulator for the supply. One ends up
actually stored in rdev->supply and the other is lost (though still
present in the supply's consumer_list).
Here is a kernel log snippet showing the issue:
[ 12.421768] gpu_cc_gx_gdsc: supplied by pm8350_s5_level
[ 12.425854] gpu_cc_gx_gdsc: supplied by pm8350_s5_level
[ 12.429064] debugfs: Directory 'regulator.4-SUPPLY' with parent
'17a00000.rsc:rpmh-regulator-gfxlvl-pm8350_s5_level'
already present!
Avoid this race condition by holding the rdev->mutex lock inside
of regulator_resolve_supply() while checking and setting
rdev->supply.
Signed-off-by: David Collins <collinsd@codeaurora.org>
Link: https://lore.kernel.org/r/1610068562-4410-1-git-send-email-collinsd@codeaurora.org
Signed-off-by: Mark Brown <broonie@kernel.org>
Yang Yingliang