Add power management for sleep as well as runtime pm.
Signed-off-by: Adriana Reus <adriana.reus@intel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Keep track of the als and px enabled/disabled status in
order to enable them selectively.
Signed-off-by: Adriana Reus <adriana.reus@intel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
This chip supports two power modes.
1. "one-shot" mode - the chip activates and executes one complete
conversion loop and then shuts itself down. This is the default mode
chosen for raw reads.
2. "continuous" mode - the chip takes continuous measurements.
Continuous mode is more expensive power-wise but may be more reliable.
Add a property so that if preferred, the default power mode for raw
reads can be set to continuous.
Separate one-shot enabling in a separate function that will be used
depending on the chosen power mode. Also create a function for
powering the chip on and off.
Signed-off-by: Adriana Reus <adriana.reus@intel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Add missing pm_runtime_mark_last_busy to apds9960_set_power_state
function.
Unless pm_runtime_mark_last_busy is called the
pm_runtime_put_autosuspend may put the device into suspend before the
delay time requested.
Signed-off-by: Matt Ranostay <mranostay@gmail.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
At probe, runtime pm should be setup before registering the sysfs interface so
that all the power attributes are accurate and functional when registering.
Also, when removing the device we should unregister first to make sure
that the interfaces that may result in wakeups are no longer available.
Fix this behaviour for the following drivers: bmc150, bmg160, kmx61,
kxcj-1013, mma9551, mma9553, rpr0521.
Signed-off-by: Adriana Reus <adriana.reus@intel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Make sure we poweroff the chip if for any reason iio_register
returns an error.
Signed-off-by: Adriana Reus <adriana.reus@intel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Print an error message to indicate that invalid configuration data was
provided in the platform_data, rather than just aborting initialization.
Signed-off-by: Bjorn Andersson <bjorn.andersson@sonymobile.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
This patch is a tidy up of warnings from the autobuilder.
>> drivers/iio/light/apds9960.c:495:32: sparse: cast to restricted __le16
drivers/iio/light/apds9960.c:635:24: sparse: cast to restricted __le16
>> drivers/iio/light/apds9960.c:672:21: sparse: incorrect type in assignment (different base types)
drivers/iio/light/apds9960.c:672:21: expected unsigned short [unsigned] [usertype] buf
drivers/iio/light/apds9960.c:672:21: got restricted __le16 [usertype] <noident>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Cc: mranostay@gmail.com
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Commit 845c877009 ("i2c / ACPI: Assign IRQ for devices that have
GpioInt automatically") automatically assigns the first ACPI GPIO
interrupt in client->irq, so we can remove the probing code from
drivers that use only one interrupt.
Signed-off-by: Octavian Purdila <octavian.purdila@intel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Since commit dab472eb93 ("i2c / ACPI: Use 0 to indicate that
device does not have interrupt assigned") 0 is not a valid i2c
client irq anymore, so change all driver's checks accordingly.
The same issue occurs when the device is instantiated via device tree
with no IRQ, or from the i2c sysfs interface, even before the patch
above.
Signed-off-by: Octavian Purdila <octavian.purdila@intel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
New device support
* APDS9960 ALS + proximity driver
* bmg160 SPI devices.
* HDC100x humidity sensors
* Holt HI-8435 threshold detector
* mma8453Q accelerometer added to the mma8452 driver
* mma86452FC and mma8653FC accelerometers added to the mma8452 driver
* mxc4005 accelerometer
* PulsedLight LIDAR
* SensorTech VZ89x volatile organic compound sensor
* UPISEMI uS5182d ALS and proximity sensors
New core functionality
* triggered events - use triggers to check for changes in threshold type
detectors on devices with out interrupt support. First user is the holt
comparator.
* chemical concentration and resistance channel types.
New driver functionality
* vf610
- buffer support.
- followup coccinelle warning fix.
Core rework
* buffers
- break out callback buffer to own module.
- move buffer implementations to a new subdirectory
* percolate the error code form iio_event_getfd out to userspace
rather than giving a missleading error later on.
Cleanups
* adddac drivers
- use BIT macro where appropriate.
* meter drivers
- use BIT macro where appropriate.
* ad7303
- add an OF match table to line up with the binding docs.
* adc128s052
- add an OF match table to line up with the binding docs.
* adf4350
- add an OF match table to line up with the binding docs
* as3935
- add an OF match table to line up with the binding docs.
* berlin2-adc
- use GENMASK and BIT for masks
- prevent attempting to sample multiple channels at once by moving a
mutex scop
- coding style cleanups
* bmg150_magn
- kconfig sort order was wrong - fix it.
* bmg160
- use i2c regmap and drop all uses of i2c_client
- separate i2c and core driver
* cc10001_adc
- kconfig sort order was wrong - fix it.
* evgen (dummy driver helper module)
- move interrupt generation to irq_work to reduce differences between
the dummy driver and real hardware drivers.
* hmc5843
- set the name dynamically rather than to a fixed value for one of the
suported parts.
- export module alias information to allow autoprobing of module.
* lpc32xx
- on failure to get resource or irq return -ENXIO as uppose to -EBUSY
* max1027
- set .of_match_table to actually allow OF style matching.
* max5821
- add MODULE_DEVICE_TABLE for OF table.
* mma8452
- refactor to separate out chip specific data.
- add freefall / motion interrupt source for devices that do their
interrupts slightly differently.
- update copywrite notice.
- leave naming of events directory in sysfs to the core
* mcp320x
- set .of_match_table so that it can be use for OF style matching.
* mlx90614
- Implement filter configuration (note the datasheet changed as a result
of the driver reviews to include the values we needed ;)
* opt3001
- drop .owner field as assigned by platform driver core.
* si7020
- replace a bitmask on the humidity values with a more correct range
check.
* stk310
- improved error handling.
- use BIT macro where appropriate and use the resulting defines
instead of magic numbers in the code.
- fix indentation
* st-sensors
- add debugfs register read hook
* tsl4531
- fix error handling in check_id
* twl6030
- fix module autoload for OF
* iio-trig-sysfs
- document add and remove attribute
* trigger in staging
- code alignment fixes.
- braces on both branches of if statement if needed for one.
* xilinx-xadc
- push interrupts into hardirq context as there isn't much in them
any more and it avoids breaking PREEMPT_RT builds due to the use
of a spinlock between the hardirq and the thread.
Tools
* event-monitor
- report unsupported events. We keep expanding what can come from drivers
so give a helpful error if one turns up in an out of date userspace
program.
* generic-buffer
- helpful message about needing to enable a channel to start the buffer.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=E+jf
-----END PGP SIGNATURE-----
Merge tag 'iio-for-4.4a' of git://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio into staging-next
Jonathan writes:
First round of new driver, new functionality and cleanups for IIO in the 4.4 cycle
New device support
* APDS9960 ALS + proximity driver
* bmg160 SPI devices.
* HDC100x humidity sensors
* Holt HI-8435 threshold detector
* mma8453Q accelerometer added to the mma8452 driver
* mma86452FC and mma8653FC accelerometers added to the mma8452 driver
* mxc4005 accelerometer
* PulsedLight LIDAR
* SensorTech VZ89x volatile organic compound sensor
* UPISEMI uS5182d ALS and proximity sensors
New core functionality
* triggered events - use triggers to check for changes in threshold type
detectors on devices with out interrupt support. First user is the holt
comparator.
* chemical concentration and resistance channel types.
New driver functionality
* vf610
- buffer support.
- followup coccinelle warning fix.
Core rework
* buffers
- break out callback buffer to own module.
- move buffer implementations to a new subdirectory
* percolate the error code form iio_event_getfd out to userspace
rather than giving a missleading error later on.
Cleanups
* adddac drivers
- use BIT macro where appropriate.
* meter drivers
- use BIT macro where appropriate.
* ad7303
- add an OF match table to line up with the binding docs.
* adc128s052
- add an OF match table to line up with the binding docs.
* adf4350
- add an OF match table to line up with the binding docs
* as3935
- add an OF match table to line up with the binding docs.
* berlin2-adc
- use GENMASK and BIT for masks
- prevent attempting to sample multiple channels at once by moving a
mutex scop
- coding style cleanups
* bmg150_magn
- kconfig sort order was wrong - fix it.
* bmg160
- use i2c regmap and drop all uses of i2c_client
- separate i2c and core driver
* cc10001_adc
- kconfig sort order was wrong - fix it.
* evgen (dummy driver helper module)
- move interrupt generation to irq_work to reduce differences between
the dummy driver and real hardware drivers.
* hmc5843
- set the name dynamically rather than to a fixed value for one of the
suported parts.
- export module alias information to allow autoprobing of module.
* lpc32xx
- on failure to get resource or irq return -ENXIO as uppose to -EBUSY
* max1027
- set .of_match_table to actually allow OF style matching.
* max5821
- add MODULE_DEVICE_TABLE for OF table.
* mma8452
- refactor to separate out chip specific data.
- add freefall / motion interrupt source for devices that do their
interrupts slightly differently.
- update copywrite notice.
- leave naming of events directory in sysfs to the core
* mcp320x
- set .of_match_table so that it can be use for OF style matching.
* mlx90614
- Implement filter configuration (note the datasheet changed as a result
of the driver reviews to include the values we needed ;)
* opt3001
- drop .owner field as assigned by platform driver core.
* si7020
- replace a bitmask on the humidity values with a more correct range
check.
* stk310
- improved error handling.
- use BIT macro where appropriate and use the resulting defines
instead of magic numbers in the code.
- fix indentation
* st-sensors
- add debugfs register read hook
* tsl4531
- fix error handling in check_id
* twl6030
- fix module autoload for OF
* iio-trig-sysfs
- document add and remove attribute
* trigger in staging
- code alignment fixes.
- braces on both branches of if statement if needed for one.
* xilinx-xadc
- push interrupts into hardirq context as there isn't much in them
any more and it avoids breaking PREEMPT_RT builds due to the use
of a spinlock between the hardirq and the thread.
Tools
* event-monitor
- report unsupported events. We keep expanding what can come from drivers
so give a helpful error if one turns up in an out of date userspace
program.
* generic-buffer
- helpful message about needing to enable a channel to start the buffer.
drivers/iio/light/apds9960.c:1125:3-8: No need to set .owner here. The core will do it.
Remove .owner field if calls are used which set it automatically
Generated by: scripts/coccinelle/api/platform_no_drv_owner.cocci
CC: Matt Ranostay <mranostay@gmail.com>
Signed-off-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
drivers/iio/light/apds9960.c:986:1-4: WARNING: end returns can be simpified
Simplify a trivial if-return sequence. Possibly combine with a
preceding function call.
Generated by: scripts/coccinelle/misc/simple_return.cocci
CC: Matt Ranostay <mranostay@gmail.com>
Signed-off-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Add support for UPISEMI us5182d als and proximity sensor.
Supports raw readings.
Data sheet for this device can be found here:
http://www.upi-semi.com/temp/uS5182D-DS-P0103-temp.pdf
Signed-off-by: Adriana Reus <adriana.reus@intel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Core changes:
- Root out the wrapper devm_gpiod_get() and gpiod_get() etc
versions of the descriptor calls that did not use the flags
argument on the end. This was around for too long and eventually
Uwe Kleine-König took the time to clean it out and the last
users are removed along with the macros in this tag. In several
cases the use of flags simplifies the code. For this reason we
have (ACKed) patches hitting in DRM, IIO, media, NFC, USB+PHY
up until we hammer in the nail with removing the macros.
- Add a fat document describing how much ready-made GPIO stuff
we have i the kernel to discourage people from reinventing
a square wheel in userspace, as so often happens.
- Create a separate lockdep class for each instance of a GPIO
IRQ chip instead of using one class for all chips, as the current
code will not work with systems with several GPIO chips doing
lockdep debugging.
- Protect against driver unloading also when a GPIO line is only
used as IRQ for the GPIOLIB_IRQCHIP helpers.
- If the GPIO chip has no designated owner, assign the parent
device driver owner as owner.
- Consolidation of chained IRQ handler install/remove replacing
all call sites where irq_set_handler_data() and
irq_set_chained_handler() were done in succession with a
combined call to irq_set_chained_handler_and_data(). This
series was created by Thomas Gleixner after the problem was
observed by Russell King.
- Tglx also made another series of patches switching
__irq_set_handler_locked() for irq_set_handler_locked() which
is way cleaner.
- Tglx and Jiang Liu wrote a good bunch of patches to make use of
irq_desc_get_xxx() accessors and avoid looking up irq_descs
from IRQ numbers. The goal is to get rid of the irq number
from the handlers in the IRQ flow which is nice.
- Rob Herring killed off the set_irq_flags() for all GPIO
drivers. This was an ARM specific function that is replaced
with the generic irq_modify_status() where special flags
are actually needed.
- When an OF node has a pin range for its GPIOs, return
-EPROBE_DEFER if the pin controller isn't available.
Pretty logical, yet needed to be fixed.
- If a driver using GPIOLIB_IRQCHIP has its own
irq_*_resources call back, then call these instead of the
defaults provided by the GPIOLIB.
- Fix an undocumented ABI hole: named GPIOs were not
properly documented.
Driver improvements:
- Add get_direction() support to the generic GPIO driver, it's
strange that we didn't have that before.
- Make it possible to have input-only GPIO chips using the
generic GPIO driver.
- Clean out platform data support from the Emma Mobile (EM)
driver
- Finegrained runtime PM support for the RCAR driver.
- Support r8a7795 (R-car H3) in the RCAR driver.
- Support interrupts on GPIOs 16 thru 31 in the DaVinci driver.
- Some consolidation and new support in the MPC8xxx driver,
we now support MPC5125.
- Preempt-RT-friendly patches: the OMAP, MPC8xxx, drivers uses raw
spinlocks making it work better with the realime patches.
- Interrupt support for the EXTRAXFS GPIO driver.
- Make the ETRAXFS GPIO driver support also ARTPEC-3.
- Interrupt and wakeup support for the BRCMSTB driver, also for
wakeup from S5 cold boot.
- Mask MXC IRQs during suspend.
- Improve OMAP2 GPIO set_debounce() to work according to spec.
- The VF610 driver handles IRQs properly.
New drivers:
- ZTE ZX GPIO driver.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=iQ2P
-----END PGP SIGNATURE-----
Merge tag 'gpio-v4.3-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio
Pull GPIO updates from Linus Walleij:
"This is the bulk of GPIO changes for the v4.3 kernel cycle.
There is quite a lot going on in the GPIO subsystem this merge window,
so the main matter is decribed below.
The hits in other subsystems when making the GPIO flags optional are
all ACKed by their respective subsystem maintainers.
Core changes:
- Root out the wrapper devm_gpiod_get() and gpiod_get() etc versions
of the descriptor calls that did not use the flags argument on the
end. This was around for too long and eventually Uwe Kleine-König
took the time to clean it out and the last users are removed along
with the macros in this tag. In several cases the use of flags
simplifies the code. For this reason we have (ACKed) patches
hitting in DRM, IIO, media, NFC, USB+PHY up until we hammer in the
nail with removing the macros.
- Add a fat document describing how much ready-made GPIO stuff we
have i the kernel to discourage people from reinventing a square
wheel in userspace, as so often happens.
- Create a separate lockdep class for each instance of a GPIO IRQ
chip instead of using one class for all chips, as the current code
will not work with systems with several GPIO chips doing lockdep
debugging.
- Protect against driver unloading also when a GPIO line is only used
as IRQ for the GPIOLIB_IRQCHIP helpers.
- If the GPIO chip has no designated owner, assign the parent device
driver owner as owner.
- Consolidation of chained IRQ handler install/remove replacing all
call sites where irq_set_handler_data() and
irq_set_chained_handler() were done in succession with a combined
call to irq_set_chained_handler_and_data().
This series was created by Thomas Gleixner after the problem was
observed by Russell King.
- Tglx also made another series of patches switching
__irq_set_handler_locked() for irq_set_handler_locked() which is
way cleaner.
- Tglx and Jiang Liu wrote a good bunch of patches to make use of
irq_desc_get_xxx() accessors and avoid looking up irq_descs from
IRQ numbers. The goal is to get rid of the irq number from the
handlers in the IRQ flow which is nice.
- Rob Herring killed off the set_irq_flags() for all GPIO drivers.
This was an ARM specific function that is replaced with the generic
irq_modify_status() where special flags are actually needed.
- When an OF node has a pin range for its GPIOs, return -EPROBE_DEFER
if the pin controller isn't available. Pretty logical, yet needed
to be fixed.
- If a driver using GPIOLIB_IRQCHIP has its own irq_*_resources call
back, then call these instead of the defaults provided by the
GPIOLIB.
- Fix an undocumented ABI hole: named GPIOs were not properly
documented.
Driver improvements:
- Add get_direction() support to the generic GPIO driver, it's
strange that we didn't have that before.
- Make it possible to have input-only GPIO chips using the generic
GPIO driver.
- Clean out platform data support from the Emma Mobile (EM) driver
- Finegrained runtime PM support for the RCAR driver.
- Support r8a7795 (R-car H3) in the RCAR driver.
- Support interrupts on GPIOs 16 thru 31 in the DaVinci driver.
- Some consolidation and new support in the MPC8xxx driver, we now
support MPC5125.
- Preempt-RT-friendly patches: the OMAP, MPC8xxx, drivers uses raw
spinlocks making it work better with the realime patches.
- Interrupt support for the EXTRAXFS GPIO driver.
- Make the ETRAXFS GPIO driver support also ARTPEC-3.
- Interrupt and wakeup support for the BRCMSTB driver, also for
wakeup from S5 cold boot.
- Mask MXC IRQs during suspend.
- Improve OMAP2 GPIO set_debounce() to work according to spec.
- The VF610 driver handles IRQs properly.
New drivers:
- ZTE ZX GPIO driver"
* tag 'gpio-v4.3-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio: (87 commits)
Revert "gpio: extraxfs: fix returnvar.cocci warnings"
gpio: tc3589x: use static container helper
gpio: xlp: fix error return code
gpio: vf610: handle level IRQ's properly
gpio: max732x: Fix error handling in probe()
gpio: omap: fix clk_prepare/unprepare usage
gpio: omap: protect regs access in omap_gpio_irq_handler
gpio: omap: fix omap2_set_gpio_debounce
gpio: omap: switch to use platform_get_irq
gpio: omap: remove wrong irq_domain_remove usage in probe
gpiolib: add description for gpio irqchip fields in struct gpio_chip
gpio: extraxfs: fix returnvar.cocci warnings
gpiolib: irqchip: use different lockdep class for each gpio irqchip
gpio/grgpio: fix deadlock in grgpio_irq_unmap()
Documentation: gpio: consumer: describe active low property
gpio: mxc: fix section mismatch warning
gpio/mxc: mask gpio interrupts in suspend
gpio: omap: Fix missing raw locks conversion
gpio: brcmstb: support wakeup from S5 cold boot
gpio: brcmstb: Add interrupt and wakeup source support
...
The tsl4531_check_id() function returned 1 on "found" and 0 on "not
found" and negative error codes on failure. This was non-standard and
bug prone. The caller treated all non-zero values including error codes
as "found".
This patch fixes it by changing the tsl4531_check_id() to return zero on
success or a negative error code, and updates the caller.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Peter Meerwald <pmeerw@pmeerw.net>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
APDS9960 is a combination of ALS, proximity, and gesture sensors.
This patch adds support for these functions along with gain control,
integration time, and event thresholds.
Signed-off-by: Matt Ranostay <mranostay@gmail.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
drivers/iio/light/opt3001.c:796:3-8: No need to set .owner here. The core will do it.
Remove .owner field if calls are used which set it automatically
Generated by: scripts/coccinelle/api/platform_no_drv_owner.cocci
CC: Andreas Dannenberg <dannenberg@ti.com>
Signed-off-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Indicate the bit number of predefined states, make use of these names and
change the state type in _resume to u8 to avoid type casting.
Signed-off-by: Hartmut Knaack <knaack.h@gmx.de>
Reviewed-by: Tiberiu Breana <tiberiu.a.breana@intel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Check for the following error cases:
* lower boundary for val in _write_event
* return value of regmap_(field_)read
* possible values for chan->type
* return value of stk3310_gpio_probe
Also add an error path in _probe to put the sensor back into stand-by mode
in case of serious errors.
Signed-off-by: Hartmut Knaack <knaack.h@gmx.de>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Take 2 also includes a fix set that was too late for the 4.2 cycle.
As we had a lot of tools and docs work in this set, I have broken those
out into their own categories in this description.
Fixes from the pull request '4th set of IIO fixes for the 4.2 cycle'.
* Poll functions for both event chardev and the buffer one were returning
negative error codes (via a positive value).
* A recent change to lsiio adding some error handling that was wrong and
stopped the tool working.
* bmg160 was missing some dependencies in Kconfig
* berlin2-adc had a misshandled register (wrote a value rather than a bitmap)
New device support
* TI opt3001 light sensor
* TXC PA12 ALS and proximity sensor.
* mcp3301 ADC support (in mcp320x driver)
* ST lsm303agr accelerometer and magnetometer drivers (plus some st-sensors
common support to allow different WHOAMI register addresses, devices with
fixed scale and allow interrupt equiped magnetometers).
* ADIS16305, ADIS16367, ADIS16445IMUs (in the adis16400 driver)
* ADIS16266 gyro (in the adis16260 driver)
* ADIS16137 gyro (in the adis16136 driver)
New functionality
* mmc35240 DT bindings.
* Inverse unit conversion macros to aid handing of values written to sysfs
attributes.
Core cleanup
* Forward declaration of struct iio_trigger to avoid a compile warning.
Driver cleanup / fixes
* mxs-lradc
- Clarify which parts are supported.
- Fix spelling erorrs.
- Missing/extra includes
- reorder includes
- add datasheet name listings for all usable channels (to allow them
to be bound by name from consumer drivers)
* acpi-als - add some function prefixes as per general iio style.
* bmc150_magn - replace a magic value with the existing define.
* vf610 - determine possible sample frequencies taking into account the
electrical characteristics (defining a minimum sample time)
* dht11
- whitespace
- additional docs
- avoid mulitple assignments in one line
- Use the new funciton ktime_get_resolution_ns to cleanup a nasty trick
previously used for timing.
* Fix all drivers that consider 0 a valid IRQ for historical reasons.
* Export I2C module alias info where previously missing (to allow autoprobing)
* Export OF module alias info where previously missing.
* mmc35240 - switch some variables into arrays to improve readability.
* mlx90614 - define some magic numbers for readability.
* bmc150_magn
- expand area locked by a mutex to cover all the use of the
data->buffer.
- use descriptive naming for a mask instead of a magic value.
* berin2-adc
- pass up an error code rather that a generic error
- constify the iio_chan_spec
- some other little tidy ups.
* stk8312
- fix a dependency on triggered buffers in kconfig
- add a check for invalid attribute values
- improve error handling by returning error codes where possible and
return immediately where relevant
- rework macro defs to use GENMASK etc
- change some variable types to reduce unnecessary casting
- clean up code style
- drop a local buffer copy for bulk reads and use the one in data->buffer
instead.
* adis16400 - the adis16448 gyroscope scale was wrong.
* adis16480 - some more wrong scales for various parts.
* adis16300 - has an undocumented product id and serial number registers so
use them.
* iio_simple_dummy - fix some wrong code indentation.
* bmc150-accel - use the chip ID to detect the chip present rather than
verifying the expected part was there. This was in response to a wrong
ACPI entry on the WinBook TW100.
* mma8452
- fix _get_hp_filter_index
- drop a double include
- pass up an error code rather than rewriting it
- range check input values to attribute writes
- register defs tidy up using GENMASK and reordering them to be easier to
follow.
- various coding style cleanups
- put the Kconfig entry in the write place (alphabetically).
Tools related
* Tools cleanup - drop an explicity NULL comparison, some unnecessary braces,
use the ARRAY_SIZE macro, send error messages to stderr instead of dropping
them in the middle of normal output.
* Fix tools to allow that scale and offset attributes are optional.
* More tools fixes including allowing true 32bit data (previously an overflow
prevented more than 31bits)
* Drop a stray header guard that ended up in a c file.
* Make calc_digits static as it isn't exported or in the header.
* Set ci_array pointer to NULL after free as a protection against non safe
usage of the tools core code. Also convert a double pointer to a single
one as the extra level of indirection was unnecessary.
Docs
* DocBook introduction by Daniel Baluta. Glad we are beginning to
draw together some more introductory docs to suplement the various
tools / examples.
* Drop bytes_per_datum sysfs attribute docs as it no longer exists.
* A whole load of missing / fixing of kernel-doc for the core of IIO.
* Document the trigger name sysfs attribute in the ABI docs.
* Minor typos in the ABI docs related to power down modes.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=/b3G
-----END PGP SIGNATURE-----
Merge tag 'iio-for-4.3b-2' of git://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio into staging-next
Jonathan writes:
Second set of new device support, features and cleanup for the 4.3 cycle.
Take 2 also includes a fix set that was too late for the 4.2 cycle.
As we had a lot of tools and docs work in this set, I have broken those
out into their own categories in this description.
Fixes from the pull request '4th set of IIO fixes for the 4.2 cycle'.
* Poll functions for both event chardev and the buffer one were returning
negative error codes (via a positive value).
* A recent change to lsiio adding some error handling that was wrong and
stopped the tool working.
* bmg160 was missing some dependencies in Kconfig
* berlin2-adc had a misshandled register (wrote a value rather than a bitmap)
New device support
* TI opt3001 light sensor
* TXC PA12 ALS and proximity sensor.
* mcp3301 ADC support (in mcp320x driver)
* ST lsm303agr accelerometer and magnetometer drivers (plus some st-sensors
common support to allow different WHOAMI register addresses, devices with
fixed scale and allow interrupt equiped magnetometers).
* ADIS16305, ADIS16367, ADIS16445IMUs (in the adis16400 driver)
* ADIS16266 gyro (in the adis16260 driver)
* ADIS16137 gyro (in the adis16136 driver)
New functionality
* mmc35240 DT bindings.
* Inverse unit conversion macros to aid handing of values written to sysfs
attributes.
Core cleanup
* Forward declaration of struct iio_trigger to avoid a compile warning.
Driver cleanup / fixes
* mxs-lradc
- Clarify which parts are supported.
- Fix spelling erorrs.
- Missing/extra includes
- reorder includes
- add datasheet name listings for all usable channels (to allow them
to be bound by name from consumer drivers)
* acpi-als - add some function prefixes as per general iio style.
* bmc150_magn - replace a magic value with the existing define.
* vf610 - determine possible sample frequencies taking into account the
electrical characteristics (defining a minimum sample time)
* dht11
- whitespace
- additional docs
- avoid mulitple assignments in one line
- Use the new funciton ktime_get_resolution_ns to cleanup a nasty trick
previously used for timing.
* Fix all drivers that consider 0 a valid IRQ for historical reasons.
* Export I2C module alias info where previously missing (to allow autoprobing)
* Export OF module alias info where previously missing.
* mmc35240 - switch some variables into arrays to improve readability.
* mlx90614 - define some magic numbers for readability.
* bmc150_magn
- expand area locked by a mutex to cover all the use of the
data->buffer.
- use descriptive naming for a mask instead of a magic value.
* berin2-adc
- pass up an error code rather that a generic error
- constify the iio_chan_spec
- some other little tidy ups.
* stk8312
- fix a dependency on triggered buffers in kconfig
- add a check for invalid attribute values
- improve error handling by returning error codes where possible and
return immediately where relevant
- rework macro defs to use GENMASK etc
- change some variable types to reduce unnecessary casting
- clean up code style
- drop a local buffer copy for bulk reads and use the one in data->buffer
instead.
* adis16400 - the adis16448 gyroscope scale was wrong.
* adis16480 - some more wrong scales for various parts.
* adis16300 - has an undocumented product id and serial number registers so
use them.
* iio_simple_dummy - fix some wrong code indentation.
* bmc150-accel - use the chip ID to detect the chip present rather than
verifying the expected part was there. This was in response to a wrong
ACPI entry on the WinBook TW100.
* mma8452
- fix _get_hp_filter_index
- drop a double include
- pass up an error code rather than rewriting it
- range check input values to attribute writes
- register defs tidy up using GENMASK and reordering them to be easier to
follow.
- various coding style cleanups
- put the Kconfig entry in the write place (alphabetically).
Tools related
* Tools cleanup - drop an explicity NULL comparison, some unnecessary braces,
use the ARRAY_SIZE macro, send error messages to stderr instead of dropping
them in the middle of normal output.
* Fix tools to allow that scale and offset attributes are optional.
* More tools fixes including allowing true 32bit data (previously an overflow
prevented more than 31bits)
* Drop a stray header guard that ended up in a c file.
* Make calc_digits static as it isn't exported or in the header.
* Set ci_array pointer to NULL after free as a protection against non safe
usage of the tools core code. Also convert a double pointer to a single
one as the extra level of indirection was unnecessary.
Docs
* DocBook introduction by Daniel Baluta. Glad we are beginning to
draw together some more introductory docs to suplement the various
tools / examples.
* Drop bytes_per_datum sysfs attribute docs as it no longer exists.
* A whole load of missing / fixing of kernel-doc for the core of IIO.
* Document the trigger name sysfs attribute in the ABI docs.
* Minor typos in the ABI docs related to power down modes.
The I2C core always reports the MODALIAS uevent as "i2c:<client name"
regardless if the driver was matched using the I2C id_table or the
of_match_table. So technically there's no need for a driver to export
the OF table since currently it's not used.
In fact, the I2C device ID table is mandatory for I2C drivers since
a i2c_device_id is passed to the driver's probe function even if the
I2C core used the OF table to match the driver.
And since the I2C core uses different tables, OF-only drivers needs to
have duplicated data that has to be kept in sync and also the dev node
compatible manufacturer prefix is stripped when reporting the MODALIAS.
To avoid the above, the I2C core behavior may be changed in the future
to not require an I2C device table for OF-only drivers and report the
OF module alias. So, it's better to also export the OF table to prevent
breaking module autoloading if that happens.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
The I2C core always reports the MODALIAS uevent as "i2c:<client name"
regardless if the driver was matched using the I2C id_table or the
of_match_table. So the driver needs to export the I2C table and this
be built into the module or udev won't have the necessary information
to auto load the correct module when the device is added.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Add support for TXC PA12203001 als and proximity sensor.
Support for raw illuminance and proximity readings.
Signed-off-by: Adriana Reus <adriana.reus@intel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
TI's opt3001 light sensor is a simple and yet powerful
little device. The device provides 99% IR rejection,
automatic full-scale, very low power consumption and
measurements from 0.01 to 83k lux.
This patch adds support for that device using the IIO
framework.
See http://www.ti.com/product/opt3001 for more information.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Andreas Dannenberg <dannenberg@ti.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Data is stored in the device in be16 format. Make use of be16_to_cpu and
cpu_to_be16 to have correct endianness on any host architecture.
Signed-off-by: Hartmut Knaack <knaack.h@gmx.de>
Reviewed-by: Tiberiu Breana <tiberiu.a.breana@intel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
iio_device_register should be the last operation during probe. Therefor
move up interrupt setup code and while at it, change the check for invalid
values of client->irq to be smaller than zero.
Fixes: 3dd477acbd ("iio: light: Add threshold interrupt support for STK3310")
As the device_register makes the userspace interfaces of the device available
it is possible for requests to come in before the probe sequence has finished.
This can lead to unhandled interrupts and similar.
Signed-off-by: Hartmut Knaack <knaack.h@gmx.de>
Reviewed-by: Tiberiu Breana <tiberiu.a.breana@intel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
The use of regmap in commit 2f2c96338a requires REGMAP_I2C to be selected, in
order to meet all dependencies.
Fixes: 2f2c96338a ("iio: ltr501: Add regmap support.")
Signed-off-by: Hartmut Knaack <knaack.h@gmx.de>
Acked-by: Daniel Baluta <daniel.baluta@intel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
When filling data->als_contr, the register content read into status needs
to be used, instead of the return status value of regmap_read.
Fixes: 8592a7eefa ("iio: ltr501: Add support for ltr559 chip")
Signed-off-by: Hartmut Knaack <knaack.h@gmx.de>
Acked-by: Daniel Baluta <daniel.baluta@intel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
The stk3310 driver makes use of regmap_i2c, so this dependency needs to be
reflected in Kconfig.
Signed-off-by: Hartmut Knaack <knaack.h@gmx.de>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
In accordance with the recent proximity ABI changes,
STK3310's proximity readings should be un-inversed
in order to return low values for far-away objects
and high values for close ones.
As consequences of this change, iio event directions
have been switched and maximum proximity sensor
reference values have also been adjusted in accordance
with the real readings.
Signed-off-by: Tiberiu Breana <tiberiu.a.breana@intel.com>
Acked-by: Hartmut Knaack <knaack.h@gmx.de>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
the millisecond values in tcs3414_times should be checked against
val2, not val, which is always zero.
Signed-off-by: Peter Meerwald <pmeerw@pmeerw.net>
Reported-by: Stephan Kleisinger <stephan.kleisinger@gmail.com>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
When setting the bits for integration time, the appropriate bitmask needs
to be cleared first.
Signed-off-by: Hartmut Knaack <knaack.h@gmx.de>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Some macros and a function were missing the acpi_als_ prefix, so add it.
Signed-off-by: Hartmut Knaack <knaack.h@gmx.de>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
material in the recent merge window, hence their separation from set (a)
as the fixes-togreg branch predated the merge window. I am running rather
later with these than I would have liked hence the large set.
* stk3310 fixes from Hartmut's review that came in post merge
- fix direction of proximity inline with recent documentation
clarification.
- fix missing REGMAP_I2C dependency
- rework the error handling for raw readings to fix an failure to power
down in the event of a raw reading failing.
- fix a bug in the compensation code which was toggling an extra bit in the
register.
* mmc35240 - reported samplign frequencies were wrong.
* ltr501 fixes
- fix a case of returning the return value of a regmap_read instead of
the value read.
- fix missing regmap dependency
* sx9500 - fix missing default values for ret in a couple of places to handle
the case of no enabled channels.
* tmp006 - check that writes to info_mask elements are actually to writable
ones. Otherwise, writing to any of them will change the sampling frequency.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=1kNg
-----END PGP SIGNATURE-----
Merge tag 'iio-fixes-for-4.2b' of git://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio into staging-linus
Jonathan writes:
Second set of IIO fixes for the 4.2 cycle. Note these depend (mostly) on
material in the recent merge window, hence their separation from set (a)
as the fixes-togreg branch predated the merge window. I am running rather
later with these than I would have liked hence the large set.
* stk3310 fixes from Hartmut's review that came in post merge
- fix direction of proximity inline with recent documentation
clarification.
- fix missing REGMAP_I2C dependency
- rework the error handling for raw readings to fix an failure to power
down in the event of a raw reading failing.
- fix a bug in the compensation code which was toggling an extra bit in the
register.
* mmc35240 - reported samplign frequencies were wrong.
* ltr501 fixes
- fix a case of returning the return value of a regmap_read instead of
the value read.
- fix missing regmap dependency
* sx9500 - fix missing default values for ret in a couple of places to handle
the case of no enabled channels.
* tmp006 - check that writes to info_mask elements are actually to writable
ones. Otherwise, writing to any of them will change the sampling frequency.
* Fix a regression in hid sensors suspend time as a result of adding runtime
pm. The normal flow of waking up devices in order to go into suspend
(given the devices are normally suspended when not reading) to a regression
in suspend time on some laptops (reports of an additional 8 seconds).
Fix this by checking to see if a user action resulting in the wake up, and
make it a null operation if it didn't. Note that for hid sensors, there is
nothing useful to be done when moving into a full suspend from a runtime
suspend so they might as well be left alone.
* rochip_saradc: fix some missing MODULE_* data including the licence so that
the driver does not taint the kernel incorrectly and can build as a module.
* twl4030 - mark irq as oneshot as it always should have been.
* inv-mpu - write formats for attributes not specified, leading to miss
interpretation of the gyro scale channel when written.
* Proximity ABI clarification. This had snuck through as a mess. Some
drivers thought proximity went in one direction, some the other. We went
with the most common option, documented it and fixed up the drivers going
the other way. Fix for sx9500 included in this set.
* ad624r - fix a wrong shift in the output data.
* at91_adc - remove a false limit on the value of the STARTUP register
applied by too small a type for the device tree parameter.
* cm3323 - clear the bits when setting the integration time (otherwise
we can only ever set more bits in the relevant field).
* bmc150-accel - multiple triggers are registered, but on error were not being
unwound in the opposite order leading to removal of triggers that had not
yet successfully been registered (count down instead of up when unwinding).
* tcs3414 - ensure right part of val / val2 pair read so that the integration
time is not always 0.
* cc10001_adc - bug in kconfig dependency. Use of OR when AND was intended.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=mBqw
-----END PGP SIGNATURE-----
Merge tag 'iio-fixes-for-4.2a' of git://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio into staging-linus
Jonathan writes:
First set of IIO fixes for the 4.2 cycle.
* Fix a regression in hid sensors suspend time as a result of adding runtime
pm. The normal flow of waking up devices in order to go into suspend
(given the devices are normally suspended when not reading) to a regression
in suspend time on some laptops (reports of an additional 8 seconds).
Fix this by checking to see if a user action resulting in the wake up, and
make it a null operation if it didn't. Note that for hid sensors, there is
nothing useful to be done when moving into a full suspend from a runtime
suspend so they might as well be left alone.
* rochip_saradc: fix some missing MODULE_* data including the licence so that
the driver does not taint the kernel incorrectly and can build as a module.
* twl4030 - mark irq as oneshot as it always should have been.
* inv-mpu - write formats for attributes not specified, leading to miss
interpretation of the gyro scale channel when written.
* Proximity ABI clarification. This had snuck through as a mess. Some
drivers thought proximity went in one direction, some the other. We went
with the most common option, documented it and fixed up the drivers going
the other way. Fix for sx9500 included in this set.
* ad624r - fix a wrong shift in the output data.
* at91_adc - remove a false limit on the value of the STARTUP register
applied by too small a type for the device tree parameter.
* cm3323 - clear the bits when setting the integration time (otherwise
we can only ever set more bits in the relevant field).
* bmc150-accel - multiple triggers are registered, but on error were not being
unwound in the opposite order leading to removal of triggers that had not
yet successfully been registered (count down instead of up when unwinding).
* tcs3414 - ensure right part of val / val2 pair read so that the integration
time is not always 0.
* cc10001_adc - bug in kconfig dependency. Use of OR when AND was intended.
i2c_driver does not need to set an owner because i2c_register_driver()
will set it.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Since 39b2bbe3d7 (gpio: add flags argument to gpiod_get*() functions)
which appeared in v3.17-rc1, the gpiod_get* functions take an additional
parameter that allows to specify direction and initial value for output.
Simplify driver accordingly. Furthermore this is one caller less that
stops us making the flags argument to gpiod_get*() mandatory.
Acked-by: Jonathan Cameron <jic23@kernel.org>
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
The use of regmap in commit 2f2c96338a requires REGMAP_I2C to be selected, in
order to meet all dependencies.
Fixes: 2f2c96338a ("iio: ltr501: Add regmap support.")
Signed-off-by: Hartmut Knaack <knaack.h@gmx.de>
Acked-by: Daniel Baluta <daniel.baluta@intel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
When filling data->als_contr, the register content read into status needs
to be used, instead of the return status value of regmap_read.
Fixes: 8592a7eefa ("iio: ltr501: Add support for ltr559 chip")
Signed-off-by: Hartmut Knaack <knaack.h@gmx.de>
Acked-by: Daniel Baluta <daniel.baluta@intel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
The stk3310 driver makes use of regmap_i2c, so this dependency needs to be
reflected in Kconfig.
Signed-off-by: Hartmut Knaack <knaack.h@gmx.de>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
In accordance with the recent proximity ABI changes,
STK3310's proximity readings should be un-inversed
in order to return low values for far-away objects
and high values for close ones.
As consequences of this change, iio event directions
have been switched and maximum proximity sensor
reference values have also been adjusted in accordance
with the real readings.
Signed-off-by: Tiberiu Breana <tiberiu.a.breana@intel.com>
Acked-by: Hartmut Knaack <knaack.h@gmx.de>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
This patch adds support for ROHM RPR0521 ambient light and proximity
sensor. It offers raw readings for intensity and proximity.
Signed-off-by: Daniel Baluta <daniel.baluta@intel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
the millisecond values in tcs3414_times should be checked against
val2, not val, which is always zero.
Signed-off-by: Peter Meerwald <pmeerw@pmeerw.net>
Reported-by: Stephan Kleisinger <stephan.kleisinger@gmail.com>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Add some empty lines to visually separate logical structure blocks, as
after if-blocks or before regular returns.
Signed-off-by: Hartmut Knaack <knaack.h@gmx.de>
Reviewed-by: Daniel Baluta <daniel.baluta@intel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
In cm3323_read_raw() i is used as return variable for the integration time
index. The also existing return variable ret however is unused in this
case, although appropriate. Replace i with ret and drop it.
Signed-off-by: Hartmut Knaack <knaack.h@gmx.de>
Reviewed-by: Daniel Baluta <daniel.baluta@intel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
cm3323_get_it_bits() returns a valid error code, so pass it up in
cm3323_read_raw().
Signed-off-by: Hartmut Knaack <knaack.h@gmx.de>
Reviewed-by: Daniel Baluta <daniel.baluta@intel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Fix the typo in the module description for the CM3323.
Signed-off-by: Hartmut Knaack <knaack.h@gmx.de>
Reviewed-by: Daniel Baluta <daniel.baluta@intel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
When setting the bits for integration time, the appropriate bitmask needs
to be cleared first.
Signed-off-by: Hartmut Knaack <knaack.h@gmx.de>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
There is no need to do the assignment to indio_dev->num_channels in two
lines code.
Put it in one line.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Given Linus announced a 4.8rc coming up, hopefully time for one more
lot of IIO patches this cycle. Some of these are actually
improvements / fixes for patches earlier in the cycle.
New device support
* st_accel driver - support devices with 8 bit channels.
Cleanup
* A general cleanup of the iio tools under /tools/ from Hartmut.
I'm more than a little embarassed by how bad some of these were! Are well,
much more refined and less bug prone now.
These cover lots of stuff like unhandled error returns, memory leaks as
well as general refactoring to tidy the code up.
* iio_simple_dummy - fix memory leaks in the init functions, drop some
pointless error returns from functions that never generate errors and
make the module parameter explicitly unsigned.
* More buffer handling reworks from Lars-Peter, this time targetting hardware
buffers (a little used corner that looks likely to get more use in the near
future). Specifically:
- Always compute the masklength as inkernel buffer users may need it.
- Add a means of labeling which buffer modes a given buffer implementation
supports.
- In the case of hardware buffers, require strict scan matching rather than
matching to a superset. Currently the demux is bypassed by these drivers
(this may well not change for efficiency reasons) so allowing a superset
of channels to be selected would otherwise lead to more data than requested
confusing userspace.
Driver funcationality improvments
* mmc35240 - adds a compensation to the raw values as borrowed form Memsic's
own input driver.
* mma8452
- event support
- event debouncing
- high pass filter configuration
- triggers
* vf610 - allow conversion mode to be adjusted
Fixlets
* mmc35240
- Off by one error that by coincidence had no real effect.
- i2c_device_name should be lowercase.
- Lack of null terminator at end of attributes array.
- Avoid computing the fractional part of the magnetic field by moving
the scaling into userspace where floating point is available to simplify
the maths.
- Use a smaller sleep before assuming the measurement is done. This is
safe and improves the possible polling rate.
- Fix sensitivity on z-axis - datasheet disagrees with Memsic's releasedd
code and the value used in the code seems to be correct.
* stk3310 - make a local variable signed to ensure error handling works.
* twl4030
- fix calculation of the temperature sense current - bug unlikely
to have ever been noticed as the difference is small.
- Fix errors in descriptions.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=sNVc
-----END PGP SIGNATURE-----
Merge tag 'iio-for-v4.2c' of git://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio into staging-next
Jonathan writes:
Third round of new IIO drivers, cleanups and functionality for the 4.2 cycle.
Given Linus announced a 4.8rc coming up, hopefully time for one more
lot of IIO patches this cycle. Some of these are actually
improvements / fixes for patches earlier in the cycle.
New device support
* st_accel driver - support devices with 8 bit channels.
Cleanup
* A general cleanup of the iio tools under /tools/ from Hartmut.
I'm more than a little embarassed by how bad some of these were! Are well,
much more refined and less bug prone now.
These cover lots of stuff like unhandled error returns, memory leaks as
well as general refactoring to tidy the code up.
* iio_simple_dummy - fix memory leaks in the init functions, drop some
pointless error returns from functions that never generate errors and
make the module parameter explicitly unsigned.
* More buffer handling reworks from Lars-Peter, this time targetting hardware
buffers (a little used corner that looks likely to get more use in the near
future). Specifically:
- Always compute the masklength as inkernel buffer users may need it.
- Add a means of labeling which buffer modes a given buffer implementation
supports.
- In the case of hardware buffers, require strict scan matching rather than
matching to a superset. Currently the demux is bypassed by these drivers
(this may well not change for efficiency reasons) so allowing a superset
of channels to be selected would otherwise lead to more data than requested
confusing userspace.
Driver funcationality improvments
* mmc35240 - adds a compensation to the raw values as borrowed form Memsic's
own input driver.
* mma8452
- event support
- event debouncing
- high pass filter configuration
- triggers
* vf610 - allow conversion mode to be adjusted
Fixlets
* mmc35240
- Off by one error that by coincidence had no real effect.
- i2c_device_name should be lowercase.
- Lack of null terminator at end of attributes array.
- Avoid computing the fractional part of the magnetic field by moving
the scaling into userspace where floating point is available to simplify
the maths.
- Use a smaller sleep before assuming the measurement is done. This is
safe and improves the possible polling rate.
- Fix sensitivity on z-axis - datasheet disagrees with Memsic's releasedd
code and the value used in the code seems to be correct.
* stk3310 - make a local variable signed to ensure error handling works.
* twl4030
- fix calculation of the temperature sense current - bug unlikely
to have ever been noticed as the difference is small.
- Fix errors in descriptions.
"index" needs to be signed for the error handling to work.
Fixes: be9e6229d6 ('iio: light: Add support for Sensortek STK3310')
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Core functionality
* i and q modifiers from quadrature channels.
* IIO_CHAN_INFO_OVERSAMPLING_RATIO added.
* High pass filter attributes added to mirror the existing low pass filter
ones.
Core cleanups
* Make IIO tools building more cross compiler friendly.
* Substantial rework of the function __iio_update_buffers to greatly simplify
a hideously evolved function.
New drivers and support
* ACPI0008 ambient light sensor driver. This one has been around a long time to
will be good to finally get it into mainline.
* Berlin SOC ADC support.
* BMC150 magnetometer. The accelerometer in the same package has been supported
for quite some time, so good to have this half as well.
* m62332 DAC driver
* MEMSIC MMC35420 magnetometer.
* ROHM BH1710 and similar ambient light sensors.
* Sensortek STK3310 light sensor.
* Sensortek STK8312 accelerometer.
* Sensortek STK8BA50 accelerometer.
* ti-adc128s052 gains support form the adc122s021 2 channel ADC.
Driver cleanups and functionality.
* Allow various drivers to compile with !GPIOLIB if COMPILE_TEST enabled.
* bmc150 - decouple trigger from buffer to allow other triggers to be used.
* bmg160 - decouple trigger from buffer to allow other triggers to be used.
Fix a trivial unused field.
* Constify a load of platform_device_id structures.
* inv_mpu6050 - device tree bindings.
* hid-sensors - fix a memory leak during probe if certain errors occur.
* ltr501 - illuminance channel derived (in an non obvious fashion) from the
intensity channels.
* ltr501 - fix a boundary check on the proximity threshold.
* mlx90614 - drop a pointless return.
* mma8452 - Debugfs register access and fix a bug that had no effect (by
coincidence)
* ti_am335x_adc - add device tree bindings for sample-delay, open-delay and
averaging. The ideal settings for these tend to be board design specific.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iQIcBAABCAAGBQJVYfYpAAoJEFSFNJnE9BaI1ScQAIJ2jsFZdf8fcVnWeq0bYx9I
VUPfz/bJ/kLQRGm/LDgpMPc5o1mOE+rupwFpp/iQf15vVUN86+CRLt0qd5I/cAEg
I3qbaieS1H9Qyd2dLTgAcZAh6tH7ZvFJm/hB6T5xQAYFGY2IMq/n3qA4//W37tUb
2bKTRb67LWbGivOvwbxdSpEkBLtVcUw3UNn9nfqjB8BEAHIesh88gJkVKAAuRYqk
Tm8AzQ7EGsosz2R7mIvukSBwXBcvRyxyOxCdLBPIWSESeLwMiiat0zCfv3MxrYiD
FVpdlywoReIjDG6z9ALOm4VMtRF2m2VrjPHclQ3kYgYSgyf0fRmoiyGowv7hkeya
Z+p9ltOZ8qdis+yH1ci9Ch695HURa1m0seirX4exqiv0Crx8UF+iNIvs9Ai84Rv8
NNVlscoeEyijUaqoBb1YvG/Fryh2IEiGXTkF4Eld+EhW8AKkFFNIqR+Gwvs1YegT
02A8kHxD0GyMYJo1uEwd+TnKwCBglwsie8omkxOXqsY860DRtBr7jOxyb/RzkSVi
jGtq1Y4nxVv7q3nkn+vQDRNgAQTbH1EJfrDilpIxIWK+9onNmKMnhKnSTVNAdld/
Hhn9g/MHptQtmA+DwMcJ3Aqn0xMUdgoE9GIkMGoKSZku9H0DhWHLdxTa2lxdJFUo
OiWVvP0eJuvu0E0h4eA2
=uX2k
-----END PGP SIGNATURE-----
Merge tag 'iio-for-v4.2b' of git://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio into staging-next
Jonathan writes:
Second set of new driver, functionality and cleanups for IIO in the 4.2 cycle.
Core functionality
* i and q modifiers from quadrature channels.
* IIO_CHAN_INFO_OVERSAMPLING_RATIO added.
* High pass filter attributes added to mirror the existing low pass filter
ones.
Core cleanups
* Make IIO tools building more cross compiler friendly.
* Substantial rework of the function __iio_update_buffers to greatly simplify
a hideously evolved function.
New drivers and support
* ACPI0008 ambient light sensor driver. This one has been around a long time to
will be good to finally get it into mainline.
* Berlin SOC ADC support.
* BMC150 magnetometer. The accelerometer in the same package has been supported
for quite some time, so good to have this half as well.
* m62332 DAC driver
* MEMSIC MMC35420 magnetometer.
* ROHM BH1710 and similar ambient light sensors.
* Sensortek STK3310 light sensor.
* Sensortek STK8312 accelerometer.
* Sensortek STK8BA50 accelerometer.
* ti-adc128s052 gains support form the adc122s021 2 channel ADC.
Driver cleanups and functionality.
* Allow various drivers to compile with !GPIOLIB if COMPILE_TEST enabled.
* bmc150 - decouple trigger from buffer to allow other triggers to be used.
* bmg160 - decouple trigger from buffer to allow other triggers to be used.
Fix a trivial unused field.
* Constify a load of platform_device_id structures.
* inv_mpu6050 - device tree bindings.
* hid-sensors - fix a memory leak during probe if certain errors occur.
* ltr501 - illuminance channel derived (in an non obvious fashion) from the
intensity channels.
* ltr501 - fix a boundary check on the proximity threshold.
* mlx90614 - drop a pointless return.
* mma8452 - Debugfs register access and fix a bug that had no effect (by
coincidence)
* ti_am335x_adc - add device tree bindings for sample-delay, open-delay and
averaging. The ideal settings for these tend to be board design specific.
Added support to calculate lux value from visible
and IR spectrum adc count values. Also added IIO_LIGHT
channel to enable user read the lux value directly
from device using illuminance input ABI.
Signed-off-by: Kuppuswamy Sathyanarayanan <sathyanarayanan.kuppuswamy@linux.intel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
'channels' is allocated via kmemdup and it is never freed in the
subsequent error paths.
Use 'indio_dev->channels' directly instead, so that we avoid such
memory leak problem.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Reviewed-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Currently, proximity sensor boundary check is done
inside the switch block but outside the case
statement.Since this code will never get executed,
moved the check outside the switch case statement.
867 case IIO_PROXIMITY:
868 switch (dir) {
// Following line has been moved outside the switch block.
869 if (val > LTR501_PS_THRESH_MASK)
870 return -EINVAL;
871 case IIO_EV_DIR_RISING:
Signed-off-by: Kuppuswamy Sathyanarayanan <sathyanarayanan.kuppuswamy@linux.intel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Second version of this pull request as a small fix to a fix turned
up before Greg pulled it for a cc10001 patch near the top of the tree.
One core fix
* Set updated for a iio kfifo was incorrectly set to false during a failed
update, resulting in atttempts to repeat the failed operation appearing
to succeed.
This time I've decided to list the driver fixes in alphabetical order rather
than 'randomly'.
* axp288_adc - a recent change added a check for valid info masks when
reading channels from consumer drivers.
* bmp280 - temperature compensation was failing to read the tfine value, hence
causing a temperature of 0 to always be returned and incorrect presure
measurements.
* cc10001 - Fix channel number mapping when some channels are reserved for
remote CPUs. Fix an issue with the use of the power-up/power-down register
(basically wrong polarity). Fix an issue due to the missinterpretting the
return value from regulator_get_voltage. Add a delay before the start bit
as recommended for the hardware to avoid data corruption.
* hid pressure - fix channel spec of modfiied, but no modifier (which makes no
sense!)
* hid proximity - fix channel spec of modified, but no modifier (which makes
no sense!). Fix a memory leak in the probe function.
* mcp320x - occasional incorrect readings on dma using spi busses due to
cacheline corruption. Fixed by forcing ___cacheline_aligned for the buffers.
* mma9551 - buffer overrun fix (miss specified maximum length of buffers)
* mma9553 - endian fix on status message. Add an enable element for activity
channel. Input checking for activity period to avoid rather unpredictable
results.
* spmi-vadc - fix an overflow in the output value normalization seen on some
boards.
* st-snesors - oops due to use of a mutex that is not yet initialized during
probe.
* xilinx adc - Some wrong register addresses, a wrong address for vccaux
channel, incorrect scale on VREFP and incorrect sign on VREFN.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=PiG+
-----END PGP SIGNATURE-----
Merge tag 'iio-fixes-for-4.1a-take2' of git://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio into staging-linus
Jonathan writes:
The usual mixed bag of fixes for IIO in the 4.1 cycle.
Second version of this pull request as a small fix to a fix turned
up before Greg pulled it for a cc10001 patch near the top of the tree.
One core fix
* Set updated for a iio kfifo was incorrectly set to false during a failed
update, resulting in atttempts to repeat the failed operation appearing
to succeed.
This time I've decided to list the driver fixes in alphabetical order rather
than 'randomly'.
* axp288_adc - a recent change added a check for valid info masks when
reading channels from consumer drivers.
* bmp280 - temperature compensation was failing to read the tfine value, hence
causing a temperature of 0 to always be returned and incorrect presure
measurements.
* cc10001 - Fix channel number mapping when some channels are reserved for
remote CPUs. Fix an issue with the use of the power-up/power-down register
(basically wrong polarity). Fix an issue due to the missinterpretting the
return value from regulator_get_voltage. Add a delay before the start bit
as recommended for the hardware to avoid data corruption.
* hid pressure - fix channel spec of modfiied, but no modifier (which makes no
sense!)
* hid proximity - fix channel spec of modified, but no modifier (which makes
no sense!). Fix a memory leak in the probe function.
* mcp320x - occasional incorrect readings on dma using spi busses due to
cacheline corruption. Fixed by forcing ___cacheline_aligned for the buffers.
* mma9551 - buffer overrun fix (miss specified maximum length of buffers)
* mma9553 - endian fix on status message. Add an enable element for activity
channel. Input checking for activity period to avoid rather unpredictable
results.
* spmi-vadc - fix an overflow in the output value normalization seen on some
boards.
* st-snesors - oops due to use of a mutex that is not yet initialized during
probe.
* xilinx adc - Some wrong register addresses, a wrong address for vccaux
channel, incorrect scale on VREFP and incorrect sign on VREFN.
'channels' is allocated via kmemdup and it is never freed.
Use 'indio_dev->channels' directly instead, so that we avoid such
memory leak problem.
Reported-by: Alexey Khoroshilov <khoroshilov@ispras.ru>
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Reviewed-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
This driver adds the initial support for the ACPI Ambient Light Sensor
as defined in Section 9.2 of the ACPI specification (Revision 5.0) [1].
Sensors complying with the standard are exposed as ACPI devices with
ACPI0008 as hardware ID and provide standard methods by which the OS
can query properties of the ambient light environment the system is
currently operating in.
This driver currently allows only to get the current ambient light
illuminance reading through the _ALI method, but is ready to be
extended extended to handle _ALC, _ALT and _ALP as well.
[1] http://www.acpi.info/DOWNLOADS/ACPIspec50.pdf
Signed-off-by: Martin Liska <marxin.liska@gmail.com>
Signed-off-by: Marek Vasut <marex@denx.de>
Signed-off-by: Gabriele Mazzotta <gabriele.mzt@gmail.com>
Cc: Zhang Rui <rui.zhang@intel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
The platform_device_id is not modified by the driver and core uses it as
const.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski.k@gmail.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
The platform_device_id is not modified by the driver and core uses it as
const.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski.k@gmail.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Add support for ROHM BH1710/BH1715/BH1721/BH1750/BH1751 ambient light
sensors.
Signed-off-by: Tomasz Duszynski <tduszyns@gmail.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Added interrupt support for proximity threshold events
to the stk3310 driver.
Signed-off-by: Tiberiu Breana <tiberiu.a.breana@intel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Minimal implementation of an IIO driver for the Sensortek
STK3310 ambient light and proximity sensor. The STK3311
model is also supported.
Includes:
- ACPI support;
- read_raw and write_raw;
- reading and setting configuration parameters for gain/scale
and integration time for both ALS and PS.
- power management
Signed-off-by: Tiberiu Breana <tiberiu.a.breana@intel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
New drivers / device support
* st sensors driver, lsm303dlh magnetometer support.
* ltr501 - support ltr301 and ltr559 chips.
New functionality
* IIO_CHAN_INFO_CALIBEMISSIVITY for thermopile sensors.
* kxcjk1013 - make driver operational with external trigger.
* Add iio targets to the tools Makefile.
Cleanups
* st sensors - more helpful error message if device id wrong or irq request
fails, explicitly make the Block Data Update optional rather
than relying on writes to address 0 not doing anything, make interrupt
support optional (Not always wired, and not all devices actually have
an interrupt line.)
* kxcjk-1013 white space additions for readability, add the KXCJ9000 ACPI
id as seen in the wild.
* sx9500 - GPIO reset support, refactor the GPIO interrupt code, add power
management, optimize power usage by powering down when possible, rename
the gpio interrupt pin to be more useful, trivial return path simplification,
trivial formatting fixes.
* isl29018 - move towards ABI compliance with a view to moving this driver
out of staging, add some brackets to ensure code works as expected. Note
there is no actual bug as the condition being tested is always true
(with current devices).
* ltr501 - add regmap support to get caching etc for later patches,
fix a parameter sanity check that always fails (bug introduced
earlier in this series), ACPI enumeration support,
interrupt rate control support, interrupt support in general and
integration time control support, code alignment cleanups.
* mma9553 - a number of little cleanups following a review from Hartmut
after I'd already applied the original driver patch.
* tmp006 - prefix some defines with TMP006 for consistency.
* tsl4531 - cleanup some wrong prefixes, presumably from copy and paste.
* mlx90614 - check for errors in read values, add power management,
add emissivity setting, add device tree binding documentation,
fix a duplicate const warning.
* ti_am335x_adc - refactor the DT parsing into a separate function.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=wyz7
-----END PGP SIGNATURE-----
Merge tag 'iio-for-v4.2a' of git://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio into staging-next
Jonathan writes:
First round of new drivers, functionality and cleanups for the 4.2 cycle
New drivers / device support
* st sensors driver, lsm303dlh magnetometer support.
* ltr501 - support ltr301 and ltr559 chips.
New functionality
* IIO_CHAN_INFO_CALIBEMISSIVITY for thermopile sensors.
* kxcjk1013 - make driver operational with external trigger.
* Add iio targets to the tools Makefile.
Cleanups
* st sensors - more helpful error message if device id wrong or irq request
fails, explicitly make the Block Data Update optional rather
than relying on writes to address 0 not doing anything, make interrupt
support optional (Not always wired, and not all devices actually have
an interrupt line.)
* kxcjk-1013 white space additions for readability, add the KXCJ9000 ACPI
id as seen in the wild.
* sx9500 - GPIO reset support, refactor the GPIO interrupt code, add power
management, optimize power usage by powering down when possible, rename
the gpio interrupt pin to be more useful, trivial return path simplification,
trivial formatting fixes.
* isl29018 - move towards ABI compliance with a view to moving this driver
out of staging, add some brackets to ensure code works as expected. Note
there is no actual bug as the condition being tested is always true
(with current devices).
* ltr501 - add regmap support to get caching etc for later patches,
fix a parameter sanity check that always fails (bug introduced
earlier in this series), ACPI enumeration support,
interrupt rate control support, interrupt support in general and
integration time control support, code alignment cleanups.
* mma9553 - a number of little cleanups following a review from Hartmut
after I'd already applied the original driver patch.
* tmp006 - prefix some defines with TMP006 for consistency.
* tsl4531 - cleanup some wrong prefixes, presumably from copy and paste.
* mlx90614 - check for errors in read values, add power management,
add emissivity setting, add device tree binding documentation,
fix a duplicate const warning.
* ti_am335x_adc - refactor the DT parsing into a separate function.
Clearly the intent was to error if the value was not 0 or 1.
As implemented we have (A != 0 || A != 1) which is always true
as A is never both 0 and 1 at the same time.
As the autobuilder suggested, && makes more sense for this error
check.
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Acked-by: Kuppuswamy Sathyanarayanan <sathyanarayanan.kuppuswamy@linux.intel.com>
Cc: Daniel Baluta <daniel.baluta@intel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Added support for Liteon 301 Ambient light sensor. Since
LTR-301 and LTR-501 are register compatible(and even have same
part id), LTR-501 driver has been extended to support both
devices. LTR-501 is similar to LTR-301 in ALS sensing, But the
only difference is, LTR-501 also supports proximity sensing.
LTR-501 - ALS + Proximity combo
LTR-301 - ALS sensor.
Signed-off-by: Kuppuswamy Sathyanarayanan <sathyanarayanan.kuppuswamy@linux.intel.com>
Signed-off-by: Daniel Baluta <daniel.baluta@intel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
This device is register compatible with LTR501, with a minor difference for
ALS control register as showed below:
ALS Control register for LTR501:
7 6 5 4 3 2 1 0
+------+------+------+------+------+------+------+------+
| | | | |
| Reserved | Gain | SW | ALS Mode |
| | | Reset| |
+------+------+------+------+------+------+------+------+
ALS Control register for LTR559:
7 6 5 4 3 2 1 0
+------+------+------+------+------+------+------+------+
| | | | |
| Reserved | Gain | SW | ALS |
| | | Reset| Mode |
+------+------+------+------+------+------+------+------+
We handle this difference by introducing ltr501_chip_info.
Datasheet for LTR559 is at:
http://optoelectronics.liteon.com/upload/download/DS86-2013-0003/S_110_LTR-559ALS-01_DS_V1.pdf
Signed-off-by: Daniel Baluta <daniel.baluta@intel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Added ACPI enumeration support for LTR501 chip.
Signed-off-by: Kuppuswamy Sathyanarayanan <sathyanarayanan.kuppuswamy@linux.intel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Added rate control support for ALS and proximity
threshold interrupts.Also, Added support to modify
and read ALS & proximity sensor sampling frequency.
LTR-501 supports interrupt rate control using persistence
register settings. Writing <n> to persistence register
would generate interrupt only if there are <n> consecutive
data values outside the threshold range.
Since we don't have any existing ABI's to directly
control the persistence register count, we have implemented
the rate control using IIO_EV_INFO_PERIOD. _period event
attribute represents the amount of time in seconds an
event should be true for the device to generate the
interrupt. So using _period value and device frequency,
persistence count is calculated in driver using following
logic.
count = period / measurement_rate
If the given period is not a multiple of measurement rate then
we round up the value to next multiple.
This patch also handles change to persistence count whenever
there is change in frequency.
Signed-off-by: Kuppuswamy Sathyanarayanan <sathyanarayanan.kuppuswamy@linux.intel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
This patch adds interrupt support for Liteon 501 chip.
Interrupt will be generated whenever ALS or proximity
data exceeds values given in upper and lower threshold
register settings.
Signed-off-by: Kuppuswamy Sathyanarayanan <sathyanarayanan.kuppuswamy@linux.intel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Added support to modify and read ALS integration time.
Signed-off-by: Kuppuswamy Sathyanarayanan <sathyanarayanan.kuppuswamy@linux.intel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Added regmap support. It will be useful to handle
bitwise updates to als & ps control registers.
Signed-off-by: Kuppuswamy Sathyanarayanan <sathyanarayanan.kuppuswamy@linux.intel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Currently in_proximity_(null)_raw is getting presented as raw sysfs
attribute. Same with the scan_elements.
The modifier doesn't apply to this channel.
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Pull HID updates from Jiri Kosina:
- quite a few firmware fixes for RMI driver by Andrew Duggan
- huion and uclogic drivers have been substantially overlaping in
functionality laterly. This redundancy is fixed by hid-huion driver
being merged into hid-uclogic; work done by Benjamin Tissoires and
Nikolai Kondrashov
- i2c-hid now supports ACPI GPIO interrupts; patch from Mika Westerberg
- Some of the quirks, that got separated into individual drivers, have
historically had EXPERT dependency. As HID subsystem matured (as
well as the individual drivers), this made less and less sense. This
dependency is now being removed by patch from Jean Delvare
- Logitech lg4ff driver received a couple of improvements for mode
switching, by Michal Malý
- multitouch driver now supports clickpads, patches by Benjamin
Tissoires and Seth Forshee
- hid-sensor framework received a substantial update; namely support
for Custom and Generic pages is being added; work done by Srinivas
Pandruvada
- wacom driver received substantial update; it now supports
i2c-conntected devices (Mika Westerberg), Bamboo PADs are now
properly supported (Benjamin Tissoires), much improved battery
reporting (Jason Gerecke) and pen proximity cleanups (Ping Cheng)
- small assorted fixes and device ID additions
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/hid: (68 commits)
HID: sensor: Update document for custom sensor
HID: sensor: Custom and Generic sensor support
HID: debug: fix error handling in hid_debug_events_read()
Input - mt: Fix input_mt_get_slot_by_key
HID: logitech-hidpp: fix error return code
HID: wacom: Add support for Cintiq 13HD Touch
HID: logitech-hidpp: add a module parameter to keep firmware gestures
HID: usbhid: yet another mouse with ALWAYS_POLL
HID: usbhid: more mice with ALWAYS_POLL
HID: wacom: set stylus_in_proximity before checking touch_down
HID: wacom: use wacom_wac_finger_count_touches to set touch_down
HID: wacom: remove hardcoded WACOM_QUIRK_MULTI_INPUT
HID: pidff: effect can't be NULL
HID: add quirk for PIXART OEM mouse used by HP
HID: add HP OEM mouse to quirk ALWAYS_POLL
HID: wacom: ask for a in-prox report when it was missed
HID: hid-sensor-hub: Fix sparse warning
HID: hid-sensor-hub: fix attribute read for logical usage id
HID: plantronics: fix Kconfig default
HID: pidff: support more than one concurrent effect
...
This makes ltr501 code consistent with the coding style adopted
for the new drivers added to IIO.
We prepare the path for adding support for LTR559 chip.
Reported by checkpatch.pl
Signed-off-by: Daniel Baluta <daniel.baluta@intel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Power down device when an error occurs in order to avoid wasting
power. Move powerdown function up to be seen by the new call and
align parameters for the ltr501_write_contr() call.
Signed-off-by: Cristina Opriceana <cristina.opriceana@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
New drivers
* CM3323 color sensor.
* MS5611 pressure and temperature sensor.
New functionality
* mup6050 - create mux clients for devices described via ACPI. The reasoning
and approach taken in this patch are complex. Basically there is no
otherway of finding out what is there than by some esoteric look ups in
the ACPI data.
* cm3232 - PM support
* itg3200 - suspend/resume support
* mcp320x - add more ADCs to the kconfig to reflect what the driver supports
(this patch and the bindings got left behind when the support was added
a while back).
Docs / utils
* ti-adc128s052 - DT bindings.
* mcp3422 - DT bindings.
* mcp320x - DT bindings
* ABI docs for event threshold scale attributes, in_magn_offset, proximity
scan_element and thresh falling/rising values for accelerometers. All
elements long in use that have slipped by being explicitly documented.
* Tidy up the tools previously in drivers/staging/iio/Documentation and move
them out to /tools/iio. Yet another move that should have happened long ago.
This time Roberta Dobrescu did the leg work. Thanks!
Core Cleanups
* Export userspace IIO headers. We should have done the appropriate header
splitting a long time ago. Thanks to Daniel for sorting this out.
* Refactor the registring of attributes for buffers to move all non-custom
ones to a vector allowing easier additions to the current set in the future.
Driver Cleanups
* gpiod related cleanups. Make use of the additional parameter to specify
initial direciton to avoid extra code.
* bmc150 - Various refactorings to reduce code repitition and prepare for
hardware buffer support. Some of these cleanups are good even
without the new functionality.
* kmx61 - direct use of index to an array avoiding a structure element which
was always the index to an element in an array of that structure.
* vf610 - avoid incorrect type for return from wait_for_completion_timeout.
* gp2ap020a00f - use put_unaligned_le32 for slight code simplification.
* ade7754 - improve error handling including suppressing some build warnings.
* ade7759 - improve error handling including suppressing some build warnings.
* hmc5843 - Long line and indentation fixes. Also some constifying of various
constant data.
* ade7854 - 80+ character line splitting.
* ad2s1210 - fix wrong printf format string.
* mxs-lradc - fix wrong printf format string.
* ade7954-i2c - code alignment fixes and other trivial but worthwhile bits.
* periodic rtc trigger - make the frequency type an unsigned int as it
is always treated as such.
* jsa1212 - constify struct regmap_config as it is constant.
* ad7793 - typo in the MODULE_DESCRIPTION
* mma9551 - check gpiod_to_irq errors. Note that this doesn't actually cause
any trouble but is worth tidying up as obviously incorrect.
* mlx90614 - refactor the register symbols to make it clear which reads are to
RAM not PROM.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iQIcBAABCAAGBQJVBe4zAAoJEFSFNJnE9BaISXAP+wcVdU9PyiLdpjh7D73qbbV0
KnKJHdO+aKe4hCv6Xl0fWIbJcsxTn8ALPHkkxHnu06hd2Q9zANgdJ5dER5XB34fX
vw+EjsIdiyCDmoOVGzP5SsmbSoO3gNoR5GdWmjKFKjr0eSxinh3AmAesTVSC2T9Y
vHkjgDj3KaqN735brd2GneeG/s3jY8ZZaiTZ0jFotCtSmBAiPi8uYwIwMLmVpsVu
M3tcUPWKithRoyKBmO4tiDg2Qwnj0IhN8zyIYiUBftxCIIY7tSlQkYgRzDmrxGG2
HCITf33Ss87UH0IF1BOm5PXjQ3ClI3idtCwqCeXscAo6IXmoe/+BsXR/m2JqUTdp
EOrORyzsHc0WkJK8dnp1h1XfiBR4UQpiwce5xGFbni2ycfNBw1/J0l7QTi45D6Z7
SdGXTgt1AWd8MoWxcxMhWMPQlHsxK/XMPh10O5wD5icxo5EHvnPP0ObZ15Ax6T/V
kcO+NEJCEHH2Q/kna2M6h4FdUVBxvzjjwhdZVs8PGGfJNDij2cVwspT81lKMauwf
07S0KHEjhqbRSM0TvsMyf2li1Xwv5eu+G2FTkopESJ4a2zyaLobt/QgTu9dzg4Gh
QDJFx4xdmNv4OQ+psZuoDznjM/EV+eQR+swH7P6UDyef0jghLwVkqHxM/HYChiyP
OvZCCnHDB4EiC8jx+c43
=BmiY
-----END PGP SIGNATURE-----
Merge tag 'iio-for-4.1a' of git://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio into staging-next
Jonathan writes:
First set of new drivers, cleanups and functionality for IIO in the 4.1 cycle.
New drivers
* CM3323 color sensor.
* MS5611 pressure and temperature sensor.
New functionality
* mup6050 - create mux clients for devices described via ACPI. The reasoning
and approach taken in this patch are complex. Basically there is no
otherway of finding out what is there than by some esoteric look ups in
the ACPI data.
* cm3232 - PM support
* itg3200 - suspend/resume support
* mcp320x - add more ADCs to the kconfig to reflect what the driver supports
(this patch and the bindings got left behind when the support was added
a while back).
Docs / utils
* ti-adc128s052 - DT bindings.
* mcp3422 - DT bindings.
* mcp320x - DT bindings
* ABI docs for event threshold scale attributes, in_magn_offset, proximity
scan_element and thresh falling/rising values for accelerometers. All
elements long in use that have slipped by being explicitly documented.
* Tidy up the tools previously in drivers/staging/iio/Documentation and move
them out to /tools/iio. Yet another move that should have happened long ago.
This time Roberta Dobrescu did the leg work. Thanks!
Core Cleanups
* Export userspace IIO headers. We should have done the appropriate header
splitting a long time ago. Thanks to Daniel for sorting this out.
* Refactor the registring of attributes for buffers to move all non-custom
ones to a vector allowing easier additions to the current set in the future.
Driver Cleanups
* gpiod related cleanups. Make use of the additional parameter to specify
initial direciton to avoid extra code.
* bmc150 - Various refactorings to reduce code repitition and prepare for
hardware buffer support. Some of these cleanups are good even
without the new functionality.
* kmx61 - direct use of index to an array avoiding a structure element which
was always the index to an element in an array of that structure.
* vf610 - avoid incorrect type for return from wait_for_completion_timeout.
* gp2ap020a00f - use put_unaligned_le32 for slight code simplification.
* ade7754 - improve error handling including suppressing some build warnings.
* ade7759 - improve error handling including suppressing some build warnings.
* hmc5843 - Long line and indentation fixes. Also some constifying of various
constant data.
* ade7854 - 80+ character line splitting.
* ad2s1210 - fix wrong printf format string.
* mxs-lradc - fix wrong printf format string.
* ade7954-i2c - code alignment fixes and other trivial but worthwhile bits.
* periodic rtc trigger - make the frequency type an unsigned int as it
is always treated as such.
* jsa1212 - constify struct regmap_config as it is constant.
* ad7793 - typo in the MODULE_DESCRIPTION
* mma9551 - check gpiod_to_irq errors. Note that this doesn't actually cause
any trouble but is worth tidying up as obviously incorrect.
* mlx90614 - refactor the register symbols to make it clear which reads are to
RAM not PROM.
Minimal implementation providing raw light intensity
and integration time attribute.
Userspace applications can use GREEN channel for raw
illuminance readings following this table:
Integration Time | G Sensitivity
================================
40 ms | 0.18
80 ms | 0.09
160 ms | 0.045
320 ms | 0.0225
640 ms | 0.01125
1280 ms | 0.005625
Signed-off-by: Daniel Baluta <daniel.baluta@intel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
These are fixes for patches in the recent merge window and are in a separate
branch to avoid rebasing the main fixes-togreg branch.
* jsa1212 - select missing REGMAP_I2C
* ssp_common - build warning fix for PM functions when PM not in use.
* ak8975 - the addition of a utility library for this driver (as part of
adding new device support) led to a dependency not being inforced
for the original driver (I2C and GPIOLIB).
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=KRES
-----END PGP SIGNATURE-----
Merge tag 'iio-fixes-for-4.0b' of git://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio into staging-linus
Jonathan writes:
Second round of IIO fixes for the 4.0 cycle (or round one part two really!)
These are fixes for patches in the recent merge window and are in a separate
branch to avoid rebasing the main fixes-togreg branch.
* jsa1212 - select missing REGMAP_I2C
* ssp_common - build warning fix for PM functions when PM not in use.
* ak8975 - the addition of a utility library for this driver (as part of
adding new device support) led to a dependency not being inforced
for the original driver (I2C and GPIOLIB).
set dependent on patches in the recent merge windows will follow shortly.
* dht11 - fix a read off the end of an array, add some locking to prevent
the read function being interrupted and make sure gpio/irq lines
are not enabled for irqs during output.
* iadc - timeout should be in jiffies not msecs
* mpu6050 - avoid a null id from ACPI emumeration being dereferenced.
* mxs-lradc - fix up some interaction issues between the touchscreen driver
and iio driver. Mostly about making sure that the adc driver
only affects channels that are not being used for the
touchscreen.
* ad2s1200 - sign extension fix for a result of c type promotion.
* adis16400 - sign extension fix for a result of c type promotion.
* mcp3422 - scale table was transposed.
* ad5686 - use _optional regulator get to avoid a dummy reg being allocate
which would cause the driver to fail to initialize.
* gp2ap020a00f - select REGMAP_I2C
* si7020 - revert an incorrect cleanup up and then fix the issue that made
that cleanup seem like a good idea.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=iNyv
-----END PGP SIGNATURE-----
Merge tag 'iio-fixes-for-4.0a' of git://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio into staging-linus
Jonathan writes:
First round of fixes for IIO in the 4.0 cycle. Note a followup
set dependent on patches in the recent merge windows will follow shortly.
* dht11 - fix a read off the end of an array, add some locking to prevent
the read function being interrupted and make sure gpio/irq lines
are not enabled for irqs during output.
* iadc - timeout should be in jiffies not msecs
* mpu6050 - avoid a null id from ACPI emumeration being dereferenced.
* mxs-lradc - fix up some interaction issues between the touchscreen driver
and iio driver. Mostly about making sure that the adc driver
only affects channels that are not being used for the
touchscreen.
* ad2s1200 - sign extension fix for a result of c type promotion.
* adis16400 - sign extension fix for a result of c type promotion.
* mcp3422 - scale table was transposed.
* ad5686 - use _optional regulator get to avoid a dummy reg being allocate
which would cause the driver to fail to initialize.
* gp2ap020a00f - select REGMAP_I2C
* si7020 - revert an incorrect cleanup up and then fix the issue that made
that cleanup seem like a good idea.
The regmap_config struct may be const because it is not modified by the
driver and regmap_init() accepts pointer to const.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Add additional flag to read in async mode. In this mode the caller will get
reply via registered callback for capture_sample. Callbacks can be registered
using sensor_hub_register_callback function. The usage id parameter of the
capture_sample can be matched with the usage id of the requested attribute.
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Acked-by: Jonathan Cameron <jic23@kernel.org>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
This patch introduces the use of function put_unaligned_le32.
This is done using Coccinelle and semantic patch used is as follows:
@@ identifier tmp; expression ptr; expression y,e; type T; @@
- tmp = cpu_to_le32(y);
<+... when != tmp
- memcpy(ptr, (T)&tmp, ...);
+ put_unaligned_le32(y,ptr);
...+>
? tmp = e
@@ type T; identifier tmp; @@
- T tmp;
...when != tmp
Signed-off-by: Vaishali Thakkar <vthakkar1994@gmail.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
This patch adds missing 'select' statement for gp2ap020a00f driver.
Without regmap_i2c, we get the following error when loading the module:
Unknown symbol devm_regmap_init_i2c.
Signed-off-by: Roberta Dobrescu <roberta.dobrescu@gmail.com>
Reviewed-by: Daniel Baluta <daniel.baluta@intel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
This patch adds missing 'select' statement for jsa1212 driver.
Without regmap_i2c, we get the following error when loading the module:
Unknown symbol devm_regmap_init_i2c.
Signed-off-by: Roberta Dobrescu <roberta.dobrescu@gmail.com>
Reviewed-by: Daniel Baluta <daniel.baluta@intel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
CM3232 is an advanced ambient light sensor with I2C protocol interface.
The I2C slave address is internally hardwired as 0x10 (7-bit). Writing
to configure register is byte mode, but reading ALS register requests to
use word mode for 16-bit resolution.
Signed-off-by: Kevin Tsai <ktsai@capellamicro.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Use common hid sensor iio pm functions. Also the poll time read and
wait is part of power up function of hid sensor iio pm function, so
remove from the client drivers.
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Use common hid sensor iio pm functions. Also the poll time read and
wait is part of power up function of hid sensor iio pm function, so
remove from the client drivers.
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Signed-off-by: Roberta Dobrescu <roberta.dobrescu@gmail.com>
Reviewed-by: Daniel Baluta <daniel.baluta@intel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Signed-off-by: Roberta Dobrescu <roberta.dobrescu@gmail.com>
Reviewed-by: Daniel Baluta <daniel.baluta@intel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Updated pull request with Daniel's fix on top for the power management
Kconfig changes that had snuck in since last update of the IIO tree
worked it's way through from mainline.
Original pull message
New device support
* jsa1212 proxmity / ambient light sensor
* SM08500 supported added to the kxcjk-1013 accelerometer driver
* KMX61 Accelerometer/Magnetometer. This took a somewhat rocky path
being first merged, then reverted for a rewrite after a discussion of
how to support additional functionality and finally being merged prior
to some last reviews coming in, with resultant follow up patches.
* Freescale mma9551l driver (minor follow up warning supression patch).
* Semtech SX9500 proximity device driver.
* ak8975 gains support for ak09911 and ak09912 and drop the standalone driver
for the ak09911.
New functionality
* Dummy driver gains some virtual registers making it more flexible.
* IIO_ACTIVITY channel types, with modifiers running, walking etc. This is
to support on chip motion clasifiers. As such it is in the form of a
confidence percentage. The only devices so far only do binary decisions
but this gives us room when other devices give more nuanced clasification.
* IIO_EV_DIR_NONE type for events where there is no obvious direction.
First case is step detection.
* IIO_STEPS channel type for pedometers.
* ENABLE mask element used to control turning on counting types such as
the pedometer that need a 'start point'.
* INSTANCE event type to support things that happen once.
* info element for height calibration (used in various motion estimation
algorithms). Note heigh tof use
* dummy driver demonstration of the use of all the new bits above.
* event monitor support for the new events.
* inv_mpu6050 gains an i2c mux to allow bypassing the device to access
additional devices connected on the other side of it. Note that in
Windows these are handled by firmware on the device and not exposed
directly.
* inv_mpu6050 gains ACPI enumeration.
* inkern interface gains iio_write_channel_raw to allow in kernel users
of DAC functionality via a simple wrapper.
* Document input current readings in the ABI docs.
* Add an error message when we get an out of range error in device tree
processing for the in kernel interfaces. Basically a device tree debugging
aid.
* Add a sanity check that a scan index for a channel is unique during
registration. There to help catch bugs as this should never happen
in a bug free driver.
Cleanups and fixlets
A rework of buffer registration from Lars - a precursor to some other
upcoming new stuff (a few patches from others rolled in here as well).
* Ensure all drivers register the same channels for the device and buffer.
* Move buffer registration into the core rather than using the old
two step approach. Now we have simple ways of using a unified set channels
for both without requiring channels be exposed by both interface, this
removes a fair bit of boilerplate.
* Stop sca3000 and ad5933 (both in staging) enabling buffer channels by
default. It has long be convention in IIO to startup with no channels
enabled and leave it up to userspace to say what goes in the buffer.
Getting rid of these allows us to drop export of iio_scan_mask_set.
* Drop get_bytes_per_datum from iio_buffer_access_funcs as not been used
for a while.
* Allocate standard buffer attributes in the core rather than in every
driver with a buffer.
* Make the length attribute read only when a driver is not able to set
the length.
* Drop the get_length callback for buffers as it is already available in
struct iio_buffer.
* Drop an unused arguement form iio_kfifo_allocate and add devm allocator
for it.
* some kconfig entries gain anotation with the resulting module name.
* Fix a resulting compile issue in dummy driver due to a stub taking
wrong parameters as a result of the above rework.
* Fix an off by 2 error in copying the core assigned buffer attributes.
Other cleanups,
* Trivial space before comma fixups.
* ak8975 fixlets - none critical. Rework to allow more device support.
* Drop unnecessary sizeof(u8) calls.
* bmp280 - refactor the compensation code to reduce copy operations and
code length. A second patch futher optimized this and performed some
other minor cleanups.
* kxcjk-1013 - various power control cleanups to avoid unnecessary enable
/ disable of device. Make sure it is only controlled at all if CONFIG_PM
is enabled. Also som cleanups of error paths.
* Small cleanups in adf4530 driver - pointless message and unnecessary braces.
* Clarifiy the proximity ABI docs to make it clear it should get bigger
as we move futher away.
* Drop a misleading comment form industrialio-core.c
* Trivial white space cleanups.
* sca3000 looses an unused debug function.
* Fix char unsigned ordering in ad8366
* Increase the sleep time in ad9523 to make it predictable (value didn't
really matter so make it more than 20 msecs)
* mxs-lradc touchscreen property cleanups in device tree are fixed to ensure
the meet all the 'interesting' documentation.
* A couple of cleanups for the staging ad5933 driver to avoid unnecessary
conversion to a processed temperature vlaue in kernel and remove
platform data form the state structure as not needed after probe.
* Fix a wrong scale factor in the docs.
Misc
* Add IIO include files to the maintainers entry.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=LlJD
-----END PGP SIGNATURE-----
Merge tag 'iio-for-3.20a_take2' of git://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio into staging-testing
Jonathan writes:
First round of IIO new drivers, cleanups and functionality for the 3.20 cycle take 2
Updated pull request with Daniel's fix on top for the power management
Kconfig changes that had snuck in since last update of the IIO tree
worked it's way through from mainline.
Original pull message
New device support
* jsa1212 proxmity / ambient light sensor
* SM08500 supported added to the kxcjk-1013 accelerometer driver
* KMX61 Accelerometer/Magnetometer. This took a somewhat rocky path
being first merged, then reverted for a rewrite after a discussion of
how to support additional functionality and finally being merged prior
to some last reviews coming in, with resultant follow up patches.
* Freescale mma9551l driver (minor follow up warning supression patch).
* Semtech SX9500 proximity device driver.
* ak8975 gains support for ak09911 and ak09912 and drop the standalone driver
for the ak09911.
New functionality
* Dummy driver gains some virtual registers making it more flexible.
* IIO_ACTIVITY channel types, with modifiers running, walking etc. This is
to support on chip motion clasifiers. As such it is in the form of a
confidence percentage. The only devices so far only do binary decisions
but this gives us room when other devices give more nuanced clasification.
* IIO_EV_DIR_NONE type for events where there is no obvious direction.
First case is step detection.
* IIO_STEPS channel type for pedometers.
* ENABLE mask element used to control turning on counting types such as
the pedometer that need a 'start point'.
* INSTANCE event type to support things that happen once.
* info element for height calibration (used in various motion estimation
algorithms). Note heigh tof use
* dummy driver demonstration of the use of all the new bits above.
* event monitor support for the new events.
* inv_mpu6050 gains an i2c mux to allow bypassing the device to access
additional devices connected on the other side of it. Note that in
Windows these are handled by firmware on the device and not exposed
directly.
* inv_mpu6050 gains ACPI enumeration.
* inkern interface gains iio_write_channel_raw to allow in kernel users
of DAC functionality via a simple wrapper.
* Document input current readings in the ABI docs.
* Add an error message when we get an out of range error in device tree
processing for the in kernel interfaces. Basically a device tree debugging
aid.
* Add a sanity check that a scan index for a channel is unique during
registration. There to help catch bugs as this should never happen
in a bug free driver.
Cleanups and fixlets
A rework of buffer registration from Lars - a precursor to some other
upcoming new stuff (a few patches from others rolled in here as well).
* Ensure all drivers register the same channels for the device and buffer.
* Move buffer registration into the core rather than using the old
two step approach. Now we have simple ways of using a unified set channels
for both without requiring channels be exposed by both interface, this
removes a fair bit of boilerplate.
* Stop sca3000 and ad5933 (both in staging) enabling buffer channels by
default. It has long be convention in IIO to startup with no channels
enabled and leave it up to userspace to say what goes in the buffer.
Getting rid of these allows us to drop export of iio_scan_mask_set.
* Drop get_bytes_per_datum from iio_buffer_access_funcs as not been used
for a while.
* Allocate standard buffer attributes in the core rather than in every
driver with a buffer.
* Make the length attribute read only when a driver is not able to set
the length.
* Drop the get_length callback for buffers as it is already available in
struct iio_buffer.
* Drop an unused arguement form iio_kfifo_allocate and add devm allocator
for it.
* some kconfig entries gain anotation with the resulting module name.
* Fix a resulting compile issue in dummy driver due to a stub taking
wrong parameters as a result of the above rework.
* Fix an off by 2 error in copying the core assigned buffer attributes.
Other cleanups,
* Trivial space before comma fixups.
* ak8975 fixlets - none critical. Rework to allow more device support.
* Drop unnecessary sizeof(u8) calls.
* bmp280 - refactor the compensation code to reduce copy operations and
code length. A second patch futher optimized this and performed some
other minor cleanups.
* kxcjk-1013 - various power control cleanups to avoid unnecessary enable
/ disable of device. Make sure it is only controlled at all if CONFIG_PM
is enabled. Also som cleanups of error paths.
* Small cleanups in adf4530 driver - pointless message and unnecessary braces.
* Clarifiy the proximity ABI docs to make it clear it should get bigger
as we move futher away.
* Drop a misleading comment form industrialio-core.c
* Trivial white space cleanups.
* sca3000 looses an unused debug function.
* Fix char unsigned ordering in ad8366
* Increase the sleep time in ad9523 to make it predictable (value didn't
really matter so make it more than 20 msecs)
* mxs-lradc touchscreen property cleanups in device tree are fixed to ensure
the meet all the 'interesting' documentation.
* A couple of cleanups for the staging ad5933 driver to avoid unnecessary
conversion to a processed temperature vlaue in kernel and remove
platform data form the state structure as not needed after probe.
* Fix a wrong scale factor in the docs.
Misc
* Add IIO include files to the maintainers entry.
This patch fixes the following checkpatch.pl error:
ERROR: space prohibited before that ',' (ctx:WxE)
Signed-off-by: Roberta Dobrescu <roberta.dobrescu@gmail.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
This patch fixes the following checkpatch.pl warning:
WARNING: please write a paragraph that describes the config symbol fully
Signed-off-by: Roberta Dobrescu <roberta.dobrescu@gmail.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
This patch adds a new driver for solteam opto JSA1212 proximity and
ambient light sensor.
Basic details of the chip can be found here.
http://www.solteamopto.com.tw/detail.php?ms=3&po_unit=2&pt_unit=29&p_unit=120
Signed-off-by: Kuppuswamy Sathyanarayanan <sathyanarayanan.kuppuswamy@linux.intel.com>
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Fix the compiler error when the CONFIG_PM_OPS flag is not set.
drivers/iio/light/tsl4531.c:235:8: error: ‘tsl4531_suspend’ undeclared here (not in a function)
drivers/iio/light/tsl4531.c:235:8: error: ‘tsl4531_resume’ undeclared here (not in a function)
Signed-off-by: Dan Murphy <dmurphy@ti.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Minimal implementation. This driver provides raw illuminance readings.
This is based on drivers/hwmon/al3320.c (*) driver from msm tree written
by Tsechih Lin <Tsechih_Lin@asus.com>
* https://android.googlesource.com/kernel/msm.git
Signed-off-by: Daniel Baluta <daniel.baluta@intel.com>
Reviewed-by: Hartmut Knaack <knaack.h@gmx.de>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
This patch removes the .owner field for drivers which use the
platform_driver_register api because this is overriden in
_platform_driver_register.
Signed-off-by: Sanjeev Sharma <Sanjeev_Sharma@mentor.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
IIO_CHAN_INFO_SAMP_FREQ and IIO_CHAN_INFO_HYSTERESIS cases ignored
the actual return values (which could be -EINVAL) and instead
returned IIO_VAL_INT_PLUS_MICRO always. Return the actual value
obtained from the functions. Both functions return IIO_VAL_INT_PLUS_MICRO
upon success.
Signed-off-by: Sachin Kamat <sachin.kamat@samsung.com>
Cc: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
IIO_CHAN_INFO_SAMP_FREQ and IIO_CHAN_INFO_HYSTERESIS cases ignored
the actual return values (which could be -EINVAL) and instead
returned IIO_VAL_INT_PLUS_MICRO always. Return the actual value
obtained from the functions. Both functions return IIO_VAL_INT_PLUS_MICRO
upon success.
Signed-off-by: Sachin Kamat <sachin.kamat@samsung.com>
Cc: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
This patch changes API from iio_device_register() to devm_* API.
Using API make code simpler.
Signed-off-by: Beomho Seo <beomho.seo@samsung.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
argument has been ignored; adjust drivers accordingly
Signed-off-by: Peter Meerwald <pmeerw@pmeerw.net>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Added support for raw reading of channel. If the sensor is powered
off, it will turn on for reading value.
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Added support for raw reading of channel. If the sensor is powered
off, it will turn on for reading value.
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Added an API to allow client drivers to turn ON and OFF sensors for
quick read. Added data_read as counting varaible instead of boolean,
so that sensor is powered off only when last user released it.
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Using units and unit exponent to calculate scale which is compliant
to IIO ABI.
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
* Fix the platform data support for the at91 adc driver.
* A couple of related follow up patches get the support working again
for at91sam9260 and at91sam9g45 as the earlier patch results in a device
name change.
* A default timer value in the at91 adc driver was bonkers. Make it sane.
* Fix incorrect reporting of the integration time for the cm32181 light sensor
* Fix a missing break in the ad2s1200 driver which would have give a false
error return.
* Make sure buffer scan mask queries from userspace return 0/1 rather than
a fairly random value depending on their implementation of test_bit
* Fix leak of the i2c client and a null pointer dereference in the cm36651
driver.
* Fix a build warning on avr32 for the mxs-lradc (not exactly a critical
combination - but the issue was real).
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)
iQIcBAABAgAGBQJTSX1HAAoJEFSFNJnE9BaIGkoQAIotGana51TXPo9KYnQJaCYH
+xBfaaXEaR69lARoXT8SDGzyXPCQNOEbVfsXRwrVQ4Wl8x2hP8n9YdUrAHzZ/8O/
Wf8Z0jb81Q+KNJ+SMMgcy4kK5OU71EMMk5fbocPzD+WfQ+WlDr+My1F3yZ5UIvOM
nOUF6QCcYA0MN7dopEVIqyP8HZhrxR1YUvgzqOmp1fteYL4gFCU006WPSI30GxEv
fMM8MiWbbn9xjOsR7SBzaLEo0Hv3YC92zwSAuJxGClH/+9cKogWAaE/PiNUO3y6A
+2D0KQnGRopKy4j/QCjdPZsTmYDBxQ9vMlUOtRlOf1XAVjL6pZu2EJ2/ereShLW6
B4rev23tqgk9nyNk/Li4n+5krzvPqqOcbWNW1la769DkEt7LU+YU+hiShkDm1+0M
6hwxPd6gQxg0QUjuusi1+B5JqweAv+mEcCsQ+ga6ZK61X9bNJ6c/4YF451rkNhc6
mlC3ZqBvDALmNSVdCas0GOGHLaeWxfoT7E9G6p62h9uBVerqZ6epvlAUC6JOHotc
/qz/D1VL1+ptPAawXiFSNOb8RMJogdBfjPB9bOlYQSSHV3eF0RVNK6FQiqvc4mFX
or1pPG6lDLGm6g3NcDEjxEEVThevQpEwKmpM0TCEUMiIuxSHYN/M//P2PSeDvYwk
9k8x3fJae7dWNsGIT92y
=HMr3
-----END PGP SIGNATURE-----
Merge tag 'iio-fixes-for-3.15a' of git://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio into staging-linus
Jonathan writes:
First found of IIO fixes for the 3.15 cycle.
* Fix the platform data support for the at91 adc driver.
* A couple of related follow up patches get the support working again
for at91sam9260 and at91sam9g45 as the earlier patch results in a device
name change.
* A default timer value in the at91 adc driver was bonkers. Make it sane.
* Fix incorrect reporting of the integration time for the cm32181 light sensor
* Fix a missing break in the ad2s1200 driver which would have give a false
error return.
* Make sure buffer scan mask queries from userspace return 0/1 rather than
a fairly random value depending on their implementation of test_bit
* Fix leak of the i2c client and a null pointer dereference in the cm36651
driver.
* Fix a build warning on avr32 for the mxs-lradc (not exactly a critical
combination - but the issue was real).
During probe the driver allocates dummy I2C devices (i2c_new_dummy())
but they aren't unregistered during driver remove or probe failure.
Additionally driver does not check the return value of i2c_new_dummy().
In case of error (i2c_new_device(): memory allocation failure or I2C
address cannot be used) this function returns NULL which is later
dereferenced by i2c_smbus_{read,write}_data() functions.
Fix issues by properly checking for i2c_new_dummy() return value and
unregistering I2C devices on driver remove or probe failure.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Acked-by: Beomho Seo <beomho.seo@samsung.com>
Cc: stable@vger.kernel.org
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
In read integration time function, assign 0 to val.
Because, prevent return inaccurate value when call read integration time.
Cc: Stable@vger.kernel.org
Cc: Kevin Tsai <ktsai@capellamicro.com>
Signed-off-by: Beomho Seo <beomho.seo@samsung.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Added usage id processing for Proximity (Human Presence).
This uses IIO interfaces for triggered buffer to present data
to user mode. This uses HID sensor framework for registering
callback events from the sensor hub.
Signed-off-by: Archana Patni <archana.patni@intel.com>
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Integration time of cm32181 is guessed about milliseconds.
But cm32181_read_als_it function return IIO_VAL_INT.
So fixed to return IIO_VAL_INT_PLUS_MICRO.
Next, add .write_raw_get_fmt callback function for call iio_str_to_fixpoint.
v2: cm32181_write_als_id function fixed as it was.
Cc: Kevin Tsai <ktsai@capellamicro.com>
Signed-off-by: Beomho Seo <beomho.seo@samsung.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
This patch is fixed [read/write] integration time function.
cm36651 have integration time from 1 to 640 milliseconds.
But, print more then the thousand second. when call *_integration_time attribute.
Because read_integration_time function return IIO_VAL_INT.
read integration time function is changed return IIO_VAL_INT_PLUS_MICRO;
And then .write_raw_get_fmt callback function for parse a fixed-point number from a string.
Some description is revised milliseconds unit.
v2: cm36651_write_int_time function fixed as it was.
Signed-off-by: Beomho Seo <beomho.seo@samsung.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
New drivers:
* si7005 relative humidity and temperature sensor
* Lite-on ltr501 ambient light and proximity sensor
Cleanups
* Clean up some dead comments in max1363
* Drop some obsolete variables in adjd_s311 and tcs3472 left over from
the introduction of iio_push_to_buffers_with_timestamp.
* Drop some unneeded linux/init.h includes
* Squish a sparse warning in mpl3115 by correctly specifying a be32 variable.
* A number of cleanups and fixes for sca3000
* Drop an unneed checks in mxs-lradc, ad7303 and adis16400.
* Drop a platform_set_drvdata in viperboard after the only use of it was
removed during a devm conversion.
* Add a missing device name for ak8975 to comply with the ABI.
* Put mpu6050 into the IMU menu as it slipped out into the main menu.
* Fix a typo and some comment formatting in mpu6050.
* Document at91 ADC clock properties.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)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=nSiE
-----END PGP SIGNATURE-----
Merge tag 'iio-for-3.15a' of git://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio into staging-next
Jonathan writes:
First set of new drivers and cleanups for IIO in the 3.15 cycle.
New drivers:
* si7005 relative humidity and temperature sensor
* Lite-on ltr501 ambient light and proximity sensor
Cleanups
* Clean up some dead comments in max1363
* Drop some obsolete variables in adjd_s311 and tcs3472 left over from
the introduction of iio_push_to_buffers_with_timestamp.
* Drop some unneeded linux/init.h includes
* Squish a sparse warning in mpl3115 by correctly specifying a be32 variable.
* A number of cleanups and fixes for sca3000
* Drop an unneed checks in mxs-lradc, ad7303 and adis16400.
* Drop a platform_set_drvdata in viperboard after the only use of it was
removed during a devm conversion.
* Add a missing device name for ak8975 to comply with the ABI.
* Put mpu6050 into the IMU menu as it slipped out into the main menu.
* Fix a typo and some comment formatting in mpu6050.
* Document at91 ADC clock properties.
Included is the patch previously set as the fourth round for 3.13 which was
to late to be appropriate.
* Another endian fix (ad799x adc) due to missuse of the IIO_ST macro (which
is going away very shortly)
* A reversed error check in ad5933 which will make the probe fail.
* A buffer overflow in the example code in the documentation.
* ad799x was freeing an irq that might or might not have been requested.
* tsl2563 was checking the wrong element of chan_spec for modifiers. Thus some
sysfs reads would give the wrong values.
* A missing dependency on HAS_IOMEM in spear_adc and lpc32xx was causing some
test build failures (on s390 and perhaps elsewhere).
I also have a few fixes queued up for things that went in during the 3.14
merge window which will follow as a separate pull request (to avoid rebasing
my tree).
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)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=otUr
-----END PGP SIGNATURE-----
Merge tag 'iio-fixes-for-3.14a' of git://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio into staging-linus
Jonathan writes:
First set of IIO fixes for the 3.14 cycle.
Included is the patch previously set as the fourth round for 3.13 which was
to late to be appropriate.
* Another endian fix (ad799x adc) due to missuse of the IIO_ST macro (which
is going away very shortly)
* A reversed error check in ad5933 which will make the probe fail.
* A buffer overflow in the example code in the documentation.
* ad799x was freeing an irq that might or might not have been requested.
* tsl2563 was checking the wrong element of chan_spec for modifiers. Thus some
sysfs reads would give the wrong values.
* A missing dependency on HAS_IOMEM in spear_adc and lpc32xx was causing some
test build failures (on s390 and perhaps elsewhere).
I also have a few fixes queued up for things that went in during the 3.14
merge window which will follow as a separate pull request (to avoid rebasing
my tree).
Use the correct channel2 member instead of channel when dealing with sysfs
reads/writes
Signed-off-by: Ivaylo Dimitrov <ivo.g.dimitrov.75@gmail.com>
Acked-by: Peter Meerwald <pmeerw@pmeerw.net>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
combined ambient light (two channels) and proximity sensor with I2C
interface; the ALS channels are visible+IR and IR
datasheet is here
http://optoelectronics.liteon.com/upload/download/DS86-2012-0006/P_100_LTR-501ALS-01_PrelimDS_ver1.1.pdf
v3:
* fix use of sizeof in _read_als()
v2: (thanks to Lars-Peter Clausen)
* cannot use devm_iio_device_register() due to cleanup order in _remove()
* mutex around data wait/read
* turn info message in _probe() into check for part number
* change copyright year to 2014
Signed-off-by: Peter Meerwald <pmeerw@pmeerw.net>
Reviewed-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
None of these files are actually using any __init type directives
and hence don't need to include <linux/init.h>. Most are just a
left over from __devinit and __cpuinit removal, or simply due to
code getting copied from one driver to the next.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
len variable became obsolete with
iio_push_to_buffers_with_timestamp()
Signed-off-by: Peter Meerwald <pmeerw@pmeerw.net>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
len variable become obsolete with
iio_push_to_buffers_with_timestamp()
Signed-off-by: Peter Meerwald <pmeerw@pmeerw.net>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Add Capella Microsystem CM32181 Ambient Light Sensor IIO driver.
This driver will convert raw data to lux value under open-air
condition. Change the calibscale based on the cover material.
Signed-off-by: Kevin Tsai <ktsai@capellamicro.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
New drivers
* HID inclinometer driver.
* DHT11 humidity driver. Note that previous humidity drivers have been in
hwmon, but no one was ever entirely happy with that, and they should find
a more comfortable home in IIO (their original placement in hwmon was my
fault - oops). As this is our first humidity driver, core support is also
added.
New features
* Two of mxs-lradc channels are internally wired to a temperature sensor,
make this explicit in the driver by providing the relevant temperature
channel.
* Add support for blocking IO on buffers.
* Add a data_available call back to the interface between buffer implementations
and the core. This is much cleaner than the old, 'stufftoread' flag.
Implemented in the kfifo buffer.
Cleanups
* Last user of the old event configuration interface is converted and the
old interface dropped. Nice to be rid of this thanks to Lars-Peter's hard
work!
* Replace all remaining instances of the IIO_ST macro with explicit filling
of the scan_type structure within struct iio_chan_spec. This macro was a
bad idea, that rapidly ceased to cover all elements of the structure.
Miss reading of the macro arguements has led to a number of bugs so lets
just get rid of it. The final removal patch is awaiting for some fixes
to make their way into mainline.
In a couple of drivers, no elements of scan_type were even being used so
in those case, it has been dropped entirely.
* Drop a couple of of_match_ptr helper uses in drivers where devicetree is
not optional and hence the structures being protected by this always exist.
* Fix up some cases where data was read from a device in a particular
byte order, but he code placed it into a s16 or similar. These were
highlighted by Sparse.
* Use the new ATTRIBUTE_GROUPS macro to drop some boiler plate in the triggers
core code.
* ad7746 and ad7280a - stop storing buffers on the stack, giving cleaner code
and possibly avoiding issues with i2c bus drivers that assume they can dma
directly into the buffer. Note that this cannot currently happen as the the
i2c_smbus_read_i2c_block_data function has a memcpy from the buffer actually
passed to the bus driver. I missed this element of the commit message
and don't think it is major enough to rebase the iio tree.
* ad5791 and ad5504 stop storing buffers on the stack for an SPI driver.
Unlike the i2c drivers, this is a real issue for SPI drivers which can dma
directly into the buffer supplied.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)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=Whfv
-----END PGP SIGNATURE-----
Merge tag 'iio-for-3.14b' of git://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio into staging-next
Jonathan writes:
2nd round of new IIO drivers, features and cleanups for the 3.14 cycle.
New drivers
* HID inclinometer driver.
* DHT11 humidity driver. Note that previous humidity drivers have been in
hwmon, but no one was ever entirely happy with that, and they should find
a more comfortable home in IIO (their original placement in hwmon was my
fault - oops). As this is our first humidity driver, core support is also
added.
New features
* Two of mxs-lradc channels are internally wired to a temperature sensor,
make this explicit in the driver by providing the relevant temperature
channel.
* Add support for blocking IO on buffers.
* Add a data_available call back to the interface between buffer implementations
and the core. This is much cleaner than the old, 'stufftoread' flag.
Implemented in the kfifo buffer.
Cleanups
* Last user of the old event configuration interface is converted and the
old interface dropped. Nice to be rid of this thanks to Lars-Peter's hard
work!
* Replace all remaining instances of the IIO_ST macro with explicit filling
of the scan_type structure within struct iio_chan_spec. This macro was a
bad idea, that rapidly ceased to cover all elements of the structure.
Miss reading of the macro arguements has led to a number of bugs so lets
just get rid of it. The final removal patch is awaiting for some fixes
to make their way into mainline.
In a couple of drivers, no elements of scan_type were even being used so
in those case, it has been dropped entirely.
* Drop a couple of of_match_ptr helper uses in drivers where devicetree is
not optional and hence the structures being protected by this always exist.
* Fix up some cases where data was read from a device in a particular
byte order, but he code placed it into a s16 or similar. These were
highlighted by Sparse.
* Use the new ATTRIBUTE_GROUPS macro to drop some boiler plate in the triggers
core code.
* ad7746 and ad7280a - stop storing buffers on the stack, giving cleaner code
and possibly avoiding issues with i2c bus drivers that assume they can dma
directly into the buffer. Note that this cannot currently happen as the the
i2c_smbus_read_i2c_block_data function has a memcpy from the buffer actually
passed to the bus driver. I missed this element of the commit message
and don't think it is major enough to rebase the iio tree.
* ad5791 and ad5504 stop storing buffers on the stack for an SPI driver.
Unlike the i2c drivers, this is a real issue for SPI drivers which can dma
directly into the buffer supplied.
'cm36651_of_match' is always compiled in. Hence the
helper macro is not needed.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
A return value of callback have been changed to IIO_VAL_INT.
If not IIO_VAL_INT, driver will print wrong value(*_read_int_time).
A follow up patch will deal with a related bug in the new event handling
code.
Signed-off-by: Beomho Seo <beomho.seo@samsung.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Now that all drivers have been converted to the new event config interface we
can remove for the legacy event config interface. Also drop the '_new' suffix
for the event config interface callbacks, since those are the only callbacks
now.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Switch the cm36651 driver to the new IIO event config interface as the old one
is going to be removed.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Cc: Beomho Seo <beomho.seo@samsung.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Fixes the following warnings from sparse:
drivers/iio/light/vcnl4000.c:88:16: warning: cast to restricted __be16
drivers/iio/light/vcnl4000.c:88:16: warning: cast to restricted __be16
drivers/iio/light/vcnl4000.c:88:16: warning: cast to restricted __be16
drivers/iio/light/vcnl4000.c:88:16: warning: cast to restricted __be16
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Cc: Peter Meerwald <pmeerw@pmeerw.net>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
drivers/built-in.o: In function `gp2ap020a00f_thresh_event_handler':
powercap_sys.c:(.text+0x15f90c): undefined reference to `irq_work_queue'
make[1]: *** [vmlinux] Error 1
make[1]: Target `uImage' not remade because of errors.
make: *** [sub-make] Error 2
make: Target `uImage' not remade because of errors.
You need the IRQ work support, but GP2AP020A00F is not selecting this
symbol.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Greg Kroah-Hartman