* pci/host-tegra:
PCI: tegra: Program PADS_REFCLK_CFG* registers with per-SoC values
PCI: tegra: Program PADS_REFCLK_CFG* always, not just on legacy SoCs
PCI: tegra: Stop setting pcibios_min_mem
PCI: tegra: Use generic pci_remap_iospace() rather than ARM32-specific one
PCI: tegra: Use lower-case hex consistently for register definitions
Conflicts:
drivers/pci/host/pci-tegra.c
Drop stray pci_ioremap_io() per Thierry Reding <treding@nvidia.com>;
removal tested by Jon Hunter <jonathanh@nvidia.com>.
This code is not being built as a module by anyone:
drivers/pci/host/Kconfig:config PCI_TEGRA
drivers/pci/host/Kconfig: bool "NVIDIA Tegra PCIe controller"
Remove uses of MODULE_DESCRIPTION(), MODULE_AUTHOR(), MODULE_LICENSE(),
etc., so that when reading the driver there is no doubt it is builtin-only.
The information is preserved in comments at the top of the file.
Replace module_platform_driver() with builtin_platform_driver(), which uses
the same init level priority, so init ordering is unchanged.
Note that MODULE_DEVICE_TABLE is a no-op for non-modular code.
[bhelgaas: changelog]
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
CC: Thierry Reding <thierry.reding@gmail.com>
CC: Stephen Warren <swarren@wwwdotorg.org>
CC: Alexandre Courbot <gnurou@gmail.com>
CC: linux-tegra@vger.kernel.org
The value that should be programmed into the PADS_REFCLK register varies
per SoC. Fix the Tegra PCIe driver to program the correct values. Future
SoCs will require different values in cfg0/1, so the two values are stored
separately in the per-SoC data structures.
For reference, the values are all documented in NV bug 1771116 comment 20.
The ASIC team has validated all these values, except for the Tegra20 value
which is simply left unchanged in this patch.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Thierry Reding <treding@nvidia.com>
tegra_pcie_phy_power_on() calls tegra_pcie_phy_enable() only for legacy
SoCs. However, part of tegra_pcie_phy_enable() needs to happen in all
cases. Move that code up one level into tegra_pcie_phy_power_on().
[bhelgaas: changelog]
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
pcibios_min_mem only exists on 32-bit ARM, so using it in pci-tegra.c
prevents the driver from being used on other arches.
In __pci_assign_resource(), we clip the available area based on
PCIBIOS_MIN_MEM. On 32-bit ARM, this is pcibios_min_mem, with a default
value of 0x01000000. For Tegra, we discover the space available for PCI
resource allocation from the device tree, and the lowest address that will
ever be available is 0x12000000 (on Tegra124).
The Tegra windows are always higher than the default pcibios_min_mem, so
the __pci_assign_resource() has no effect, so there's no need to adjust
pcibios_min_mem here.
[bhelgaas: changelog]
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Use the pci_remap_iospace() function provided by the PCI core, rather
than the 32-bit ARM-specific pci_ioremap_io().
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Most of the register definitions use lowercase hexadecimal values, with a
few exceptions using uppercase. Convert the latter to be more in line with
the former.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Use devm_request_pci_bus_resources() to request host bridge window
resources instead of doing it by hand in the driver.
No functional change intended.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
41534e5378 ("PCI: tegra: Implement a proper resource hierarchy") did two
things:
1) It added a top-level resource that encloses all resources declared in
the DT description, including registers and bridge apertures, and
2) It requested the bridge apertures, which means the PCI core can track
the resources used by PCI devices below the bridge.
The latter is necessary, but the former is questionable because there's no
guarantee that the bridge registers and the apertures are contiguous. In
this example:
# cat /proc/iomem
00000000-3fffffff : /pcie-controller@00003000
00000000-00000fff : /pcie-controller@00003000/pci@1,0
00003000-000037ff : pads
00003800-000039ff : afi
10000000-1fffffff : cs
the resource tree claims that [mem 0x00003a00-0x0fffffff] is consumed by
/pcie-controller@00003000, but it's not mentioned in the DT, and it might
actually be used by other devices.
Remove the top-level resource so we don't claim more than the device
actually consumes.
This reintroduces the problem that we can't match the resources, e.g.,
"pads", "afi", "cs", etc., to the DT device. I think this should be solved
by having the DT core request all resources of all devices in the DT (it
does not do that today). If a driver claims the device, it can request the
resources it uses. For example:
# cat /proc/iomem
00000000-00000fff : /pcie-controller@00003000
00000000-00000fff : /pcie-controller@00003000/pci@1,0
00003000-000037ff : /pcie-controller@00003000
00003000-000037ff : pads
00003800-000039ff : /pcie-controller@00003000
00003800-000039ff : afi
10000000-1fffffff : /pcie-controller@00003000
10000000-1fffffff : cs
...
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
The current XUSB pad controller bindings are insufficient to describe
PHY devices attached to USB controllers. New bindings have been created
to overcome these restrictions. As a side-effect each root port now is
assigned a set of PHY devices, one for each lane associated with the
root port. This has the benefit of allowing fine-grained control of the
power management for each lane.
Acked-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
BARs are disabled when the size register is 0, so it's misleading to write
a base address into the start register.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Track the offsets of the bus -> CPU mapping for I/O and memory. This is
cosmetic for current Tegra chips because the offset is always 0. But to
properly support legacy use-cases, like VGA, this would be needed so that
PCI bus addresses can be relocated.
While at it, also request the I/O resource both in physical memory and I/O
space to make /proc/iomem consistent, as well as add the I/O region to the
list of host bridge resources.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
The num_ports field of the tegra_pcie structure is never used so remove it.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
The configuration space mapping on Tegra is somewhat special, and in order
to avoid wasting virtual address space the configuration space for each bus
needs to be stitched together from several blocks which form a single
continuous virtual address range for accessors.
Currently the configuration space is mapped upon the first access to one of
its registers. However, the mapping operation may sleep under certain
circumstances, so doing it from the configuration space accessors (they are
protected by a spin lock) will trigger a warning.
To avoid the warning, use the ->add_bus() callback to perform the mapping
at enumeration time when the operation is allowed to sleep. Also add an
implementation of ->remove_bus() that undoes the mapping established by the
->add_bus() callback. While it isn't currently possible to unload the
module, there is work underway to remedy this, and this code will come in
handy when that happens.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
On -RT and if kernel is booting with "threadirqs" cmd line parameter,
PCIe/PCI (MSI) IRQ cascade handlers (like dra7xx_pcie_msi_irq_handler())
will be forced threaded and, as result, will generate warnings like this:
WARNING: CPU: 1 PID: 82 at kernel/irq/handle.c:150 handle_irq_event_percpu+0x14c/0x174()
irq 460 handler irq_default_primary_handler+0x0/0x14 enabled interrupts
Backtrace:
(warn_slowpath_common) from (warn_slowpath_fmt+0x38/0x40)
(warn_slowpath_fmt) from (handle_irq_event_percpu+0x14c/0x174)
(handle_irq_event_percpu) from (handle_irq_event+0x84/0xb8)
(handle_irq_event) from (handle_simple_irq+0x90/0x118)
(handle_simple_irq) from (generic_handle_irq+0x30/0x44)
(generic_handle_irq) from (dra7xx_pcie_msi_irq_handler+0x7c/0x8c)
(dra7xx_pcie_msi_irq_handler) from (irq_forced_thread_fn+0x28/0x5c)
(irq_forced_thread_fn) from (irq_thread+0x128/0x204)
This happens because all of them invoke generic_handle_irq() from the
requested handler. generic_handle_irq() grabs raw_locks and thus needs to
run in raw-IRQ context.
This issue was originally reproduced on TI dra7-evem, but, as was
identified during discussion [1], other hosts can also suffer from this
issue. Fix all them at once by marking PCIe/PCI (MSI) IRQ cascade handlers
IRQF_NO_THREAD explicitly.
[1] http://lkml.kernel.org/r/1448027966-21610-1-git-send-email-grygorii.strashko@ti.com
[bhelgaas: add stable tag, fix typos]
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Lucas Stach <l.stach@pengutronix.de> (for imx6)
CC: stable@vger.kernel.org
CC: Kishon Vijay Abraham I <kishon@ti.com>
CC: Jingoo Han <jingoohan1@gmail.com>
CC: Kukjin Kim <kgene@kernel.org>
CC: Krzysztof Kozlowski <k.kozlowski@samsung.com>
CC: Richard Zhu <Richard.Zhu@freescale.com>
CC: Thierry Reding <thierry.reding@gmail.com>
CC: Stephen Warren <swarren@wwwdotorg.org>
CC: Alexandre Courbot <gnurou@gmail.com>
CC: Simon Horman <horms@verge.net.au>
CC: Pratyush Anand <pratyush.anand@gmail.com>
CC: Michal Simek <michal.simek@xilinx.com>
CC: "Sören Brinkmann" <soren.brinkmann@xilinx.com>
CC: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
set_irq_flags is ARM-specific with custom flags which have genirq
equivalents. Convert drivers to use the genirq interfaces directly, so we
can kill off set_irq_flags. The translation of flags is as follows:
IRQF_VALID -> !IRQ_NOREQUEST
IRQF_PROBE -> !IRQ_NOPROBE
IRQF_NOAUTOEN -> IRQ_NOAUTOEN
For IRQs managed by an irqdomain, the irqdomain core code handles clearing
and setting IRQ_NOREQUEST already, so there is no need to do this in .map()
functions, and we can simply remove the set_irq_flags calls. Some users
also modify IRQ_NOPROBE, and this has been maintained although it is not
clear that is really needed. There appears to be a great deal of blind
copy and paste of this code.
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Jingoo Han <jingoohan1@gmail.com>
CC: Kishon Vijay Abraham I <kishon@ti.com>
CC: Murali Karicheri <m-karicheri2@ti.com>
CC: Thierry Reding <thierry.reding@gmail.com>
CC: Stephen Warren <swarren@wwwdotorg.org>
CC: Alexandre Courbot <gnurou@gmail.com>
CC: Jingoo Han <jingoohan1@gmail.com>
CC: Pratyush Anand <pratyush.anand@gmail.com>
CC: Simon Horman <horms@verge.net.au>
CC: Michal Simek <michal.simek@xilinx.com>
CC: "Sören Brinkmann" <soren.brinkmann@xilinx.com>
After b97ea289cf ("PCI: Assign resources before drivers claim devices
(pci_scan_root_bus())"), pci_scan_root_bus() no longer adds the devices, so
it is equivalent to tegra_pcie_scan_bus().
Remove tegra_pcie_scan_bus() (the hw.scan method), so we use the generic
pci_scan_root_bus() path.
[bhelgaas: changelog]
Tested-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Yijing Wang <wangyijing@huawei.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Thierry Reding <treding@nvidia.com>
* pci/config:
PCI: xilinx: Convert to use generic config accessors
PCI: xgene: Convert to use generic config accessors
PCI: tegra: Convert to use generic config accessors
PCI: rcar: Convert to use generic config accessors
PCI: generic: Convert to use generic config accessors
powerpc/powermac: Convert PCI to use generic config accessors
powerpc/fsl_pci: Convert PCI to use generic config accessors
ARM: ks8695: Convert PCI to use generic config accessors
ARM: sa1100: Convert PCI to use generic config accessors
ARM: integrator: Convert PCI to use generic config accessors
ARM: cns3xxx: Convert PCI to use generic config accessors
PCI: Add generic config accessors
powerpc/PCI: Add struct pci_ops member names to initialization
mn10300/PCI: Add struct pci_ops member names to initialization
MIPS: PCI: Add struct pci_ops member names to initialization
frv/PCI: Add struct pci_ops member names to initialization
The bridge setup is already done by generic code while scanning the buses.
Do not duplicate (or potentially alter) this setup as a fixup.
Tested-by: Alexandre Courbot <acourbot@nvidia.com>
Reviewed-by: Thierry Reding <treding@nvidia.com>
Tested-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Here's the set of driver core patches for 3.19-rc1.
They are dominated by the removal of the .owner field in platform
drivers. They touch a lot of files, but they are "simple" changes, just
removing a line in a structure.
Other than that, a few minor driver core and debugfs changes. There are
some ath9k patches coming in through this tree that have been acked by
the wireless maintainers as they relied on the debugfs changes.
Everything has been in linux-next for a while.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iEYEABECAAYFAlSOD20ACgkQMUfUDdst+ylLPACg2QrW1oHhdTMT9WI8jihlHVRM
53kAoLeteByQ3iVwWurwwseRPiWa8+MI
=OVRS
-----END PGP SIGNATURE-----
Merge tag 'driver-core-3.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull driver core update from Greg KH:
"Here's the set of driver core patches for 3.19-rc1.
They are dominated by the removal of the .owner field in platform
drivers. They touch a lot of files, but they are "simple" changes,
just removing a line in a structure.
Other than that, a few minor driver core and debugfs changes. There
are some ath9k patches coming in through this tree that have been
acked by the wireless maintainers as they relied on the debugfs
changes.
Everything has been in linux-next for a while"
* tag 'driver-core-3.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core: (324 commits)
Revert "ath: ath9k: use debugfs_create_devm_seqfile() helper for seq_file entries"
fs: debugfs: add forward declaration for struct device type
firmware class: Deletion of an unnecessary check before the function call "vunmap"
firmware loader: fix hung task warning dump
devcoredump: provide a one-way disable function
device: Add dev_<level>_once variants
ath: ath9k: use debugfs_create_devm_seqfile() helper for seq_file entries
ath: use seq_file api for ath9k debugfs files
debugfs: add helper function to create device related seq_file
drivers/base: cacheinfo: remove noisy error boot message
Revert "core: platform: add warning if driver has no owner"
drivers: base: support cpu cache information interface to userspace via sysfs
drivers: base: add cpu_device_create to support per-cpu devices
topology: replace custom attribute macros with standard DEVICE_ATTR*
cpumask: factor out show_cpumap into separate helper function
driver core: Fix unbalanced device reference in drivers_probe
driver core: fix race with userland in device_add()
sysfs/kernfs: make read requests on pre-alloc files use the buffer.
sysfs/kernfs: allow attributes to request write buffer be pre-allocated.
fs: sysfs: return EGBIG on write if offset is larger than file size
...
Pull irq domain updates from Thomas Gleixner:
"The real interesting irq updates:
- Support for hierarchical irq domains:
For complex interrupt routing scenarios where more than one
interrupt related chip is involved we had no proper representation
in the generic interrupt infrastructure so far. That made people
implement rather ugly constructs in their nested irq chip
implementations. The main offenders are x86 and arm/gic.
To distangle that mess we have now hierarchical irqdomains which
seperate the various interrupt chips and connect them via the
hierarchical domains. That keeps the domain specific details
internal to the particular hierarchy level and removes the
criss/cross referencing of chip internals. The resulting hierarchy
for a complex x86 system will look like this:
vector mapped: 74
msi-0 mapped: 2
dmar-ir-1 mapped: 69
ioapic-1 mapped: 4
ioapic-0 mapped: 20
pci-msi-2 mapped: 45
dmar-ir-0 mapped: 3
ioapic-2 mapped: 1
pci-msi-1 mapped: 2
htirq mapped: 0
Neither ioapic nor pci-msi know about the dmar interrupt remapping
between themself and the vector domain. If interrupt remapping is
disabled ioapic and pci-msi become direct childs of the vector
domain.
In hindsight we should have done that years ago, but in hindsight
we always know better :)
- Support for generic MSI interrupt domain handling
We have more and more non PCI related MSI interrupts, so providing
a generic infrastructure for this is better than having all
affected architectures implementing their own private hacks.
- Support for PCI-MSI interrupt domain handling, based on the generic
MSI support.
This part carries the pci/msi branch from Bjorn Helgaas pci tree to
avoid a massive conflict. The PCI/MSI parts are acked by Bjorn.
I have two more branches on top of this. The full conversion of x86
to hierarchical domains and a partial conversion of arm/gic"
* 'irq-irqdomain-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (41 commits)
genirq: Move irq_chip_write_msi_msg() helper to core
PCI/MSI: Allow an msi_controller to be associated to an irq domain
PCI/MSI: Provide mechanism to alloc/free MSI/MSIX interrupt from irqdomain
PCI/MSI: Enhance core to support hierarchy irqdomain
PCI/MSI: Move cached entry functions to irq core
genirq: Provide default callbacks for msi_domain_ops
genirq: Introduce msi_domain_alloc/free_irqs()
asm-generic: Add msi.h
genirq: Add generic msi irq domain support
genirq: Introduce callback irq_chip.irq_write_msi_msg
genirq: Work around __irq_set_handler vs stacked domains ordering issues
irqdomain: Introduce helper function irq_domain_add_hierarchy()
irqdomain: Implement a method to automatically call parent domains alloc/free
genirq: Introduce helper irq_domain_set_info() to reduce duplicated code
genirq: Split out flow handler typedefs into seperate header file
genirq: Add IRQ_SET_MASK_OK_DONE to support stacked irqchip
genirq: Introduce irq_chip.irq_compose_msi_msg() to support stacked irqchip
genirq: Add more helper functions to support stacked irq_chip
genirq: Introduce helper functions to support stacked irq_chip
irqdomain: Do irq_find_mapping and set_type for hierarchy irqdomain in case OF
...
Commit 0b0b0893d4 ("of/pci: Fix the conversion of IO ranges into IO
resources") changed how I/O resources are parsed from DT. Rather than
containing the physical address of the I/O region, the addresses will now
be in I/O address space.
On Tegra the union of all ranges is used to expose a top-level memory-
mapped resource for the PCI host bridge. This helps to make /proc/iomem
more readable.
Combining both of the above, the union would now include the I/O space
region. This causes a regression on Tegra20, where the physical base
address of the PCIe controller (and therefore of the union) is located at
physical address 0x80000000. Since I/O space starts at 0, the union will
now include all of system RAM which starts at 0x00000000.
This commit fixes this by keeping two copies of the I/O range: one that
represents the range in the CPU's physical address space, the other for the
range in the I/O address space. This allows the translation setup within
the driver to reuse the physical addresses. The code registering the I/O
region with the PCI core uses both ranges to establish the mapping.
Fixes: 0b0b0893d4 ("of/pci: Fix the conversion of IO ranges into IO resources")
Reported-by: Marc Zyngier <marc.zyngier@arm.com>
Tested-by: Marc Zyngier <marc.zyngier@arm.com>
Suggested-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
The PCI/MSI irq chip callbacks mask/unmask_msi_irq have been renamed
to pci_msi_mask/unmask_irq to mark them PCI specific. Rename all usage
sites. The conversion helper functions are kept around to avoid
conflicts in next and will be removed after merging into mainline.
Coccinelle assisted conversion. No functional change.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Chris Metcalf <cmetcalf@tilera.com>
Cc: x86@kernel.org
Cc: Jiang Liu <jiang.liu@linux.intel.com>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Murali Karicheri <m-karicheri2@ti.com>
Cc: Thierry Reding <thierry.reding@gmail.com>
Cc: Mohit Kumar <mohit.kumar@st.com>
Cc: Simon Horman <horms@verge.net.au>
Cc: Michal Simek <michal.simek@xilinx.com>
Cc: Yijing Wang <wangyijing@huawei.com>
Rename write_msi_msg() to pci_write_msi_msg() to mark it as PCI
specific.
Signed-off-by: Jiang Liu <jiang.liu@linux.intel.com>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Grant Likely <grant.likely@linaro.org>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: Yingjoe Chen <yingjoe.chen@mediatek.com>
Cc: Yijing Wang <wangyijing@huawei.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Save MSI controller in pci_sys_data instead of assigning MSI controller
pointer to every PCI bus in .add_bus().
[bhelgaas: use struct tegra_msi.chip, not ctrl]
Signed-off-by: Yijing Wang <wangyijing@huawei.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
"msi_chip" isn't very descriptive, so rename it to "msi_controller". That
tells a little more about what it does and is already used in device tree
bindings.
No functional change.
[bhelgaas: changelog, change *only* the struct name so it's reviewable]
Suggested-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Yijing Wang <wangyijing@huawei.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
* pci/host-generic:
arm64: Add architectural support for PCI
PCI: Add pci_remap_iospace() to map bus I/O resources
of/pci: Add support for parsing PCI host bridge resources from DT
of/pci: Add pci_get_new_domain_nr() and of_get_pci_domain_nr()
PCI: Add generic domain handling
of/pci: Fix the conversion of IO ranges into IO resources
of/pci: Move of_pci_range_to_resource() to of/address.c
ARM: Define PCI_IOBASE as the base of virtual PCI IO space
of/pci: Add pci_register_io_range() and pci_pio_to_address()
asm-generic/io.h: Fix ioport_map() for !CONFIG_GENERIC_IOMAP
Conflicts:
drivers/pci/host/pci-tegra.c
The ranges property for a host bridge controller in DT describes the
mapping between the PCI bus address and the CPU physical address. The
resources framework however expects that the IO resources start at a pseudo
"port" address 0 (zero) and have a maximum size of IO_SPACE_LIMIT. The
conversion from PCI ranges to resources failed to take that into account,
returning a CPU physical address instead of a port number.
Also fix all the drivers that depend on the old behaviour by fetching the
CPU physical address based on the port number where it is being needed.
Signed-off-by: Liviu Dudau <Liviu.Dudau@arm.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
CC: Grant Likely <grant.likely@linaro.org>
CC: Rob Herring <robh+dt@kernel.org>
CC: Arnd Bergmann <arnd@arndb.de>
CC: Thierry Reding <thierry.reding@gmail.com>
CC: Simon Horman <horms@verge.net.au>
CC: Catalin Marinas <catalin.marinas@arm.com>
The PCIe controller on Tegra124 has two root ports that can be used in a
x4/x1 or x2/x1 configuration and can run at PCIe 2.0 link speeds (up to
5 GT/s). The PHY programming has been moved into a separate controller, so
the driver now needs to request an external PHY referenced using the device
tree.
Tested-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Depending on the prior state of the controller, the PLL reset may not be
pulsed. Clear the register bit and set it after a small delay to ensure
that the PLL is really reset.
Tested-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Eric Yuen <eyuen@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
The 16 chunks of 64 KiB that need to be stitched together to make up the
configuration space for one bus (1 MiB) are located 24 bits (== 16 MiB)
apart in physical address space. This is determined by the start of the
extended register field (bits 24-27) in the physical mapping.
Tested-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Peter Daifuku <pdaifuku@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
When a root port is disabled, disable the CLKREQ# signal if available.
Tested-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Currently the resource hierarchy generated from the PCIe host bridge is
completely flat:
$ cat /proc/iomem
00000000-00000fff : /pcie-controller@00003000/pci@1,0
00003000-000037ff : pads
00003800-000039ff : afi
10000000-1fffffff : cs
28000000-28003fff : r8169
28004000-28004fff : r8169
...
The host bridge driver doesn't request all the resources that are used.
Windows allocated to each of the root ports aren't tracked, so there is no
way for resources allocated to individual devices to be matched up with the
correct parent resource by the PCI core.
This patch addresses this in two steps. It first takes the union of all
regions associated with the PCIe host bridge (control registers, root port
registers, configuration space, I/O and prefetchable as well as non-
prefetchable memory regions) and uses it as the new root of the resource
hierarchy.
Subsequently, regions are allocated from within this new root resource so
that the resource tree looks much more like what's expected:
# cat /proc/iomem
00000000-3fffffff : /pcie-controller@00003000
00000000-00000fff : /pcie-controller@00003000/pci@1,0
00003000-000037ff : pads
00003800-000039ff : afi
10000000-1fffffff : cs
20000000-27ffffff : non-prefetchable
28000000-3fffffff : prefetchable
28000000-280fffff : PCI Bus 0000:01
28000000-28003fff : 0000:01:00.0
28000000-28003fff : r8169
28004000-28004fff : 0000:01:00.0
28004000-28004fff : r8169
...
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
We should call tegra_msi_free() to free the MSI bit if irq_create_mapping()
fails. And we need to dispose the IRQ mapping during IRQ teardown.
[bhelgaas: made irqd_to_hwirq() change suggested by Thierry]
Signed-off-by: Jisheng Zhang <jszhang@marvell.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Thierry Reding <treding@nvidia.com>
Acked-by: Thierry Reding <treding@nvidia.com>
A handful of driver-related changes. We've had a bunch of them going in through
other branches as well, so it's only a part of what we really have this release.
Larger pieces are:
* Removal of a now unused PWM driver for atmel
- This includes AVR32 changes that have been appropriately acked.
* Performance counter support for the arm CCN interconnect
* OMAP mailbox driver cleanups and consolidation
* PCI and SATA PHY drivers for SPEAr 13xx platforms
* Redefinition (with backwards compatibility!) of PCI DT bindings for Tegra to
better model regulators/power.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.14 (GNU/Linux)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=fsP6
-----END PGP SIGNATURE-----
Merge tag 'drivers-for-3.17' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC driver changes from Olof Johansson:
"A handful of driver-related changes. We've had a bunch of them going
in through other branches as well, so it's only a part of what we
really have this release.
Larger pieces are:
- Removal of a now unused PWM driver for atmel
[ This includes AVR32 changes that have been appropriately acked ]
- Performance counter support for the arm CCN interconnect
- OMAP mailbox driver cleanups and consolidation
- PCI and SATA PHY drivers for SPEAr 13xx platforms
- Redefinition (with backwards compatibility!) of PCI DT bindings for
Tegra to better model regulators/power"
Note: this merge also fixes up the semantic conflict with the new
calling convention for devm_phy_create(), see commit f0ed817638 ("phy:
core: Let node ptr of PHY point to PHY and not of PHY provider") that
came in through Greg's USB tree.
Semantic merge patch by Stephen Rothwell <sfr@canb.auug.org.au> through
the next tree.
* tag 'drivers-for-3.17' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (38 commits)
bus: arm-ccn: Fix error handling at event allocation
mailbox/omap: add a parent structure for every IP instance
mailbox/omap: remove the private mailbox structure
mailbox/omap: consolidate OMAP mailbox driver
mailbox/omap: simplify the fifo assignment by using macros
mailbox/omap: remove omap_mbox_type_t from mailbox ops
mailbox/omap: remove OMAP1 mailbox driver
mailbox/omap: use devm_* interfaces
bus: ARM CCN: add PERF_EVENTS dependency
bus: ARM CCN PMU driver
PCI: spear: Remove spear13xx_pcie_remove()
PCI: spear: Fix Section mismatch compilation warning for probe()
ARM: tegra: Remove legacy PCIe power supply properties
PCI: tegra: Remove deprecated power supply properties
PCI: tegra: Implement accurate power supply scheme
ARM: SPEAr13xx: Update defconfigs
ARM: SPEAr13xx: Add pcie and miphy DT nodes
ARM: SPEAr13xx: Add bindings and dt node for misc block
ARM: SPEAr13xx: Fix static mapping table
phy: Add drivers for PCIe and SATA phy on SPEAr13xx
...
This merge window brings a good size of cleanups on various
platforms. Among the bigger ones:
* Removal of Samsung s5pc100 and s5p64xx platforms. Both of these have
lacked active support for quite a while, and after asking around nobody
showed interest in keeping them around. If needed, they could be
resurrected in the future but it's more likely that we would prefer
reintroduction of them as DT and multiplatform-enabled platforms
instead.
* OMAP4 controller code register define diet. They defined a lot of registers
that were never actually used, etc.
* Move of some of the Tegra platform code (PMC, APBIO, fuse, powergate)
to drivers/soc so it can be shared with 64-bit code. This also converts them
over to traditional driver models where possible.
* Removal of legacy gpio-samsung driver, since the last users have been
removed (moved to pinctrl)
Plus a bunch of smaller changes for various platforms that sort of
dissapear in the diffstat for the above. clps711x cleanups, shmobile
header file refactoring/moves for multiplatform friendliness, some misc
cleanups, etc.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.14 (GNU/Linux)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=gbcE
-----END PGP SIGNATURE-----
Merge tag 'cleanup-for-3.17' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC cleanups from Olof Johansson:
"This merge window brings a good size of cleanups on various platforms.
Among the bigger ones:
- Removal of Samsung s5pc100 and s5p64xx platforms. Both of these
have lacked active support for quite a while, and after asking
around nobody showed interest in keeping them around. If needed,
they could be resurrected in the future but it's more likely that
we would prefer reintroduction of them as DT and
multiplatform-enabled platforms instead.
- OMAP4 controller code register define diet. They defined a lot of
registers that were never actually used, etc.
- Move of some of the Tegra platform code (PMC, APBIO, fuse,
powergate) to drivers/soc so it can be shared with 64-bit code.
This also converts them over to traditional driver models where
possible.
- Removal of legacy gpio-samsung driver, since the last users have
been removed (moved to pinctrl)
Plus a bunch of smaller changes for various platforms that sort of
dissapear in the diffstat for the above. clps711x cleanups, shmobile
header file refactoring/moves for multiplatform friendliness, some
misc cleanups, etc"
* tag 'cleanup-for-3.17' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (117 commits)
drivers: CCI: Correct use of ! and &
video: clcd-versatile: Depend on ARM
video: fix up versatile CLCD helper move
MAINTAINERS: Add sdhci-st file to ARCH/STI architecture
ARM: EXYNOS: Fix build breakge with PM_SLEEP=n
MAINTAINERS: Remove Kirkwood
ARM: tegra: Convert PMC to a driver
soc/tegra: fuse: Set up in early initcall
ARM: tegra: Always lock the CPU reset vector
ARM: tegra: Setup CPU hotplug in a pure initcall
soc/tegra: Implement runtime check for Tegra SoCs
soc/tegra: fuse: fix dummy functions
soc/tegra: fuse: move APB DMA into Tegra20 fuse driver
soc/tegra: Add efuse and apbmisc bindings
soc/tegra: Add efuse driver for Tegra
ARM: tegra: move fuse exports to soc/tegra/fuse.h
ARM: tegra: export apb dma readl/writel
ARM: tegra: Use a function to get the chip ID
ARM: tegra: Sort includes alphabetically
ARM: tegra: Move includes to include/soc/tegra
...
Provide a debugfs file ("pcie/ports") that shows the current link status
for each root port.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Stephen Warren <swarren@nvidia.com>
The current description of power supplies doesn't match the hardware.
Instead it's designed to support the needs of current designs, which
will break as soon as a new design appears that cannot be described
using the current assumptions.
In order to fully support all possible future designs, all power supply
inputs to the PCIe block need to be accurately described and separately
configurable.
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
This commit converts the PMC support code to a platform driver. Because
the boot process needs to call into this driver very early, also set up
a minimal environment via an early initcall.
Signed-off-by: Thierry Reding <treding@nvidia.com>
In order to not clutter the include/linux directory with SoC specific
headers, move the Tegra-specific headers out into a separate directory.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Per license_is_gpl_compatible(), the MODULE_LICENSE() string for GPL v2 is
"GPL v2", not "GPLv2". Use "GPL v2" so this module doesn't taint the
kernel.
[bhelgaas: changelog]
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Jingoo Han <jg1.han@samsung.com>
Use new OF interrupt mapping (of_irq_parse_and_map_pci()) when possible.
This is the recommended method of doing the IRQ mapping. For old
devicetrees we fall back to the previous practice.
This allows interrupts to be remapped across bridges.
Tested-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
This is the branch where we usually queue up cleanup efforts, moving
drivers out of the architecture directory, header file restructuring,
etc. Sometimes they tangle with new development so it's hard to keep it
strictly to cleanups.
Some of the things included in this branch are:
* Atmel SAMA5 conversion to common clock
* Reset framework conversion for tegra platforms
- Some of this depends on tegra clock driver reworks that are shared with Mike
Turquette's clk tree.
* Tegra DMA refactoring, which are shared branches with the DMA tree.
* Removal of some header files on exynos to prepare for multiplatform
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=3CcT
-----END PGP SIGNATURE-----
Merge tag 'cleanup-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC cleanups from Olof Johansson:
"This is the branch where we usually queue up cleanup efforts, moving
drivers out of the architecture directory, header file restructuring,
etc. Sometimes they tangle with new development so it's hard to keep
it strictly to cleanups.
Some of the things included in this branch are:
* Atmel SAMA5 conversion to common clock
* Reset framework conversion for tegra platforms
- Some of this depends on tegra clock driver reworks that are shared
with Mike Turquette's clk tree.
* Tegra DMA refactoring, which are shared branches with the DMA tree.
* Removal of some header files on exynos to prepare for
multiplatform"
* tag 'cleanup-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (169 commits)
ARM: mvebu: move Armada 370/XP specific definitions to armada-370-xp.h
ARM: mvebu: remove prototypes of non-existing functions from common.h
ARM: mvebu: move ARMADA_XP_MAX_CPUS to armada-370-xp.h
serial: sh-sci: Rework baud rate calculation
serial: sh-sci: Compute overrun_bit without using baud rate algo
serial: sh-sci: Remove unused GPIO request code
serial: sh-sci: Move overrun_bit and error_mask fields out of pdata
serial: sh-sci: Support resources passed through platform resources
serial: sh-sci: Don't check IRQ in verify port operation
serial: sh-sci: Set the UPF_FIXED_PORT flag
serial: sh-sci: Remove duplicate interrupt check in verify port op
serial: sh-sci: Simplify baud rate calculation algorithms
serial: sh-sci: Remove baud rate calculation algorithm 5
serial: sh-sci: Sort headers alphabetically
ARM: EXYNOS: Kill exynos_pm_late_initcall()
ARM: EXYNOS: Consolidate selection of PM_GENERIC_DOMAINS for Exynos4
ARM: at91: switch Calao QIL-A9260 board to DT
clk: at91: fix pmc_clk_ids data type attriubte
PM / devfreq: use inclusion <mach/map.h> instead of <plat/map-s5p.h>
ARM: EXYNOS: remove <mach/regs-clock.h> for exynos
...
Tegra's clock driver now provides an implementation of the common
reset API (include/linux/reset.h). Use this instead of the old Tegra-
specific API; that will soon be removed.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-By: Terje Bergstrom <tbergstrom@nvidia.com>
Reviewed-by: Thierry Reding <treding@nvidia.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Tegra's clock driver now provides an implementation of the common
reset API (include/linux/reset.h). Use this instead of the old Tegra-
specific API; that will soon be removed.
The old Tegra-specific API used a struct clock to represent the module
to reset. Some of the clocks retrieved during probe() were only used for
reset purposes, and indeed aren't even true clocks. So, there's no need
to get() them any more.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Thierry Reding <treding@nvidia.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Bjorn Helgaas