Control IRQ is the first IRQ vector. This complicates handling of
completion irqs as we need to offset them by one.
in the next patch, there are scenarios where completion and control EQs
will share the same irq. for example: functions with single IRQ. To ease
such scenarios, we shift control IRQ to the end of the irq array.
Signed-off-by: Shay Drory <shayd@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Currently mlx5_core_dev contains array of capabilities. It contains 19
valid capabilities of the device, 2 reserved entries and 12 holes.
Due to this for 14 unused entries, mlx5_core_dev allocates 14 * 8K = 112K
bytes of memory which is never used. Due to this mlx5_core_dev structure
size is 270Kbytes odd. This allocation further aligns to next power of 2
to 512Kbytes.
By skipping non-existent entries,
(a) 112Kbyte is saved,
(b) mlx5_core_dev reduces to 8KB with alignment
(c) 350KB saved in alignment
In future individual capability allocation can be used to skip its
allocation when such capability is disabled at the device level. This
patch prepares mlx5_core_dev to hold capability using a pointer instead
of inline array.
Signed-off-by: Parav Pandit <parav@nvidia.com>
Reviewed-by: Leon Romanovsky <leonro@nvidia.com>
Reviewed-by: Shay Drory <shayd@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
In the current code, the current and maximal capabilities are
maintained in separate arrays which are both per type. In order to
allow the creation of such a basic structure as a dynamically
allocated array, we move curr and max fields to a unified
structure so that specific capabilities can be allocated as one unit.
Signed-off-by: Parav Pandit <parav@nvidia.com>
Reviewed-by: Leon Romanovsky <leonro@nvidia.com>
Reviewed-by: Shay Drory <shayd@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
New mlx5_core device structure is allocated through devlink_alloc
with\ kzalloc and that ensures that all fields are equal to zero
and it includes ->state too.
That means that checks of that field in the mlx5_init_one() is
completely redundant, because that function is called only once
in the begging of mlx5_core_dev lifetime.
PCI:
.probe()
-> probe_one()
-> mlx5_init_one()
The recovery flow can't run at that time or before it, because relevant
work initialized later in mlx5_init_once().
Such initialization flow ensures that dev->state can't be
MLX5_DEVICE_STATE_UNINITIALIZED at all, so remove such impossible
checks.
Signed-off-by: Leon Romanovsky <leonro@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
The CQ destroy is performed based on the IRQ number that is stored in
cq->irqn. That number wasn't set explicitly during CQ creation and as
expected some of the API users of mlx5_core_create_cq() forgot to update
it.
This caused to wrong synchronization call of the wrong IRQ with a number
0 instead of the real one.
As a fix, set the IRQ number directly in the mlx5_core_create_cq() and
update all users accordingly.
Fixes: 1a86b377aa ("vdpa/mlx5: Add VDPA driver for supported mlx5 devices")
Fixes: ef1659ade3 ("IB/mlx5: Add DEVX support for CQ events")
Signed-off-by: Shay Drory <shayd@nvidia.com>
Reviewed-by: Tariq Toukan <tariqt@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
As shared FDB requires changes in two subsystems first expose the needed
core functions so the RDMA side can be changed.
mlx5_lag_is_master(): return true if a given mlx5 device is the lag master.
mlx5_lag_is_shared_fdb(): Returns true if the lag mode is shared FDB.
mlx5_lag_get_peer_mdev(): Return the peer mdev in lag.
The mentioned functions will be used by downstream patches in order
to add support for shared FDB for the RDMA side.
Signed-off-by: Mark Bloch <mbloch@nvidia.com>
Reviewed-by: Mark Zhang <markzhang@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Trivial conflicts in net/can/isotp.c and
tools/testing/selftests/net/mptcp/mptcp_connect.sh
scaled_ppm_to_ppb() was moved from drivers/ptp/ptp_clock.c
to include/linux/ptp_clock_kernel.h in -next so re-apply
the fix there.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Running devlink reload command for port in switchdev mode cause
resources to corrupt: driver can't release allocated EQ and reclaim
memory pages, because "rdma" auxiliary device had add CQs which blocks
EQ from deletion.
Erroneous sequence happens during reload-down phase, and is following:
1. detach device - suspends auxiliary devices which support it, destroys
others. During this step "eth-rep" and "rdma-rep" are destroyed,
"eth" - suspended.
2. disable SRIOV - moves device to legacy mode; as part of disablement -
rescans drivers. This step adds "rdma" auxiliary device.
3. destroy EQ table - <failure>.
Driver shouldn't create any device during unload flows. To handle that
implement MLX5_PRIV_FLAGS_DETACH flag, set it on device detach and unset
on device attach. If flag is set do no-op on drivers rescan.
Fixes: a925b5e309 ("net/mlx5: Register mlx5 devices to auxiliary virtual bus")
Signed-off-by: Dmytro Linkin <dlinkin@nvidia.com>
Reviewed-by: Leon Romanovsky <leonro@nvidia.com>
Reviewed-by: Roi Dayan <roid@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Misc update for mlx5 driver,
1) Clean up patches for lag and SF
2) Reserve bit 31 in steering register C1 for IPSec offload usage
3) Move steering tables pool logic into the steering core and
increase the maximum table size to 2G entries when software steering
is enabled.
-----BEGIN PGP SIGNATURE-----
iQEzBAABCAAdFiEEGhZs6bAKwk/OTgTpSD+KveBX+j4FAmCv6vAACgkQSD+KveBX
+j6qnAgAz0eKWKCsFCqlXGIgF1cg3FrGR5W2Zi5euriHhHwNqnZof3AIMkzcXjLL
wBlPjWk3YLfBaBNPTziz6EJuGl1vZZxuSdc7bqsNnl0srujRtQFu3JyerdgXEXNL
W2NxjSTiVwu8lq2qlYauQvcE0v+JrB/LMe9tvq1UQ2v9FtBMMhs9hGUSCro2huwj
XYF0m0ve89+mYlm6/m0SIUpPVdMiIhm4+coO1wibk7+8jn6+ZT6EJbbZvjc9eQg7
ZKr8f/TpfmvHToG8LPOc6HqHzRiHlp3Yzsft+xm54r082n4F/noGhL+Hqvvj1aTj
C6Ip5N7VkzT+erMLMrjIbrmEP94cyQ==
=torZ
-----END PGP SIGNATURE-----
Merge tag 'mlx5-updates-2021-05-26' of git://git.kernel.org/pub/scm/linux/kernel/git/saeed/linux
Saeed Mahameed says:
====================
mlx5-updates-2021-05-26
Misc update for mlx5 driver,
1) Clean up patches for lag and SF
2) Reserve bit 31 in steering register C1 for IPSec offload usage
3) Move steering tables pool logic into the steering core and
increase the maximum table size to 2G entries when software steering
is enabled.
* tag 'mlx5-updates-2021-05-26' of git://git.kernel.org/pub/scm/linux/kernel/git/saeed/linux:
net/mlx5: Fix lag port remapping logic
net/mlx5: Use boolean arithmetic to evaluate roce_lag
net/mlx5: Remove unnecessary spin lock protection
net/mlx5: Cap the maximum flow group size to 16M entries
net/mlx5: DR, Set max table size to 2G entries
net/mlx5: Move chains ft pool to be used by all firmware steering
net/mlx5: Move table size calculation to steering cmd layer
net/mlx5: Add case for FS_FT_NIC_TX FT in MLX5_CAP_FLOWTABLE_TYPE
net/mlx5: DR, Remove unused field of send_ring struct
net/mlx5e: RX, Remove unnecessary check in RX CQE compression handling
net/mlx5e: IPsec/rep_tc: Fix rep_tc_update_skb drops IPsec packet
net/mlx5e: TC: Reserved bit 31 of REG_C1 for IPsec offload
net/mlx5e: TC: Use bit counts for register mapping
net/mlx5: CT: Avoid reusing modify header context for natted entries
net/mlx5e: CT, Remove newline from ct_dbg call
====================
Link: https://lore.kernel.org/r/20210527185624.694304-1-saeed@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Firmware FT pool is per device, but the software tracking of this pool
only services fs_chains users, and if another layer takes a flow table,
the pool will not be updated, and fs_chains will fail creating a flow
table, with no recovery till the flow table is returned.
Move FT pool to be global per device, and stored at the cmd level,
so all layers can use it.
Signed-off-by: Paul Blakey <paulb@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
mlx5_core_dev holds pointer to static profile, hence when the
log_max_qp of the profile is override by some device, then it
effect all other mlx5 devices that share the same profile.
Fix it by having a profile instance for every mlx5 device.
Fixes: 883371c453 ("net/mlx5: Check FW limitations on log_max_qp before setting it")
Signed-off-by: Maor Gottlieb <maorg@nvidia.com>
Reviewed-by: Mark Bloch <mbloch@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
This is significantly bug fixes and general cleanups. The noteworthy new
features are fairly small:
- XRC support for HNS and improves RQ operations
- Bug fixes and updates for hns, mlx5, bnxt_re, hfi1, i40iw, rxe, siw and
qib
- Quite a few general cleanups on spelling, error handling, static checker
detections, etc
- Increase the number of device ports supported beyond 255. High port
count software switches now exist
- Several bug fixes for rtrs
- mlx5 Device Memory support for host controlled atomics
- Report SRQ tables through to rdma-tool
-----BEGIN PGP SIGNATURE-----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=vsXA
-----END PGP SIGNATURE-----
Merge tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rdma/rdma
Pull rdma updates from Jason Gunthorpe:
"This is significantly bug fixes and general cleanups. The noteworthy
new features are fairly small:
- XRC support for HNS and improves RQ operations
- Bug fixes and updates for hns, mlx5, bnxt_re, hfi1, i40iw, rxe, siw
and qib
- Quite a few general cleanups on spelling, error handling, static
checker detections, etc
- Increase the number of device ports supported beyond 255. High port
count software switches now exist
- Several bug fixes for rtrs
- mlx5 Device Memory support for host controlled atomics
- Report SRQ tables through to rdma-tool"
* tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rdma/rdma: (145 commits)
IB/qib: Remove redundant assignment to ret
RDMA/nldev: Add copy-on-fork attribute to get sys command
RDMA/bnxt_re: Fix a double free in bnxt_qplib_alloc_res
RDMA/siw: Fix a use after free in siw_alloc_mr
IB/hfi1: Remove redundant variable rcd
RDMA/nldev: Add QP numbers to SRQ information
RDMA/nldev: Return SRQ information
RDMA/restrack: Add support to get resource tracking for SRQ
RDMA/nldev: Return context information
RDMA/core: Add CM to restrack after successful attachment to a device
RDMA/cma: Skip device which doesn't support CM
RDMA/rxe: Fix a bug in rxe_fill_ip_info()
RDMA/mlx5: Expose private query port
RDMA/mlx4: Remove an unused variable
RDMA/mlx5: Fix type assignment for ICM DM
IB/mlx5: Set right RoCE l3 type and roce version while deleting GID
RDMA/i40iw: Fix error unwinding when i40iw_hmc_sd_one fails
RDMA/cxgb4: add missing qpid increment
IB/ipoib: Remove unnecessary struct declaration
RDMA/bnxt_re: Get rid of custom module reference counting
...
Add needed structure layouts and defines for pddr register
(Port Diagnostics Database Register) and the troublshooting page.
This will be used to get extended link state from the monitor opcode
bits.
Signed-off-by: Moshe Tal <moshet@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Saeed Mahameed says:
====================
This pr contains changes from mlx5-next branch,
already reviewed on netdev and rdma mailing lists, links below.
1) From Leon, Dynamically assign MSI-X vectors count
Already Acked by Bjorn Helgaas.
https://patchwork.kernel.org/project/netdevbpf/cover/20210314124256.70253-1-leon@kernel.org/
2) Cleanup series:
https://patchwork.kernel.org/project/netdevbpf/cover/20210311070915.321814-1-saeed@kernel.org/
From Mark, E-Switch cleanups and refactoring, and the addition
of single FDB mode needed HW bits.
From Mikhael, Remove unused struct field
From Saeed, Cleanup W=1 prototype warning
From Zheng, Esw related cleanup
From Tariq, User order-0 page allocation for EQs
====================
* mlx5-next:
net/mlx5: Implement sriov_get_vf_total_msix/count() callbacks
net/mlx5: Dynamically assign MSI-X vectors count
net/mlx5: Add dynamic MSI-X capabilities bits
PCI/IOV: Add sysfs MSI-X vector assignment interface
net/mlx5: Use order-0 allocations for EQs
net/mlx5: Add IFC bits needed for single FDB mode
net/mlx5: E-Switch, Refactor send to vport to be more generic
RDMA/mlx5: Use representor E-Switch when getting netdev and metadata
net/mlx5: E-Switch, Add eswitch pointer to each representor
net/mlx5: E-Switch, Add match on vhca id to default send rules
net/mlx5: Remove unused mlx5_core_health member recover_work
net/mlx5: simplify the return expression of mlx5_esw_offloads_pair()
net/mlx5: Cleanup prototype warning
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
Saeed Mahameed says:
====================
mlx5-next 2021-04-09
This pr contains changes from mlx5-next branch,
already reviewed on netdev and rdma mailing lists, links below.
1) From Leon, Dynamically assign MSI-X vectors count
Already Acked by Bjorn Helgaas.
https://patchwork.kernel.org/project/netdevbpf/cover/20210314124256.70253-1-leon@kernel.org/
2) Cleanup series:
https://patchwork.kernel.org/project/netdevbpf/cover/20210311070915.321814-1-saeed@kernel.org/
From Mark, E-Switch cleanups and refactoring, and the addition
of single FDB mode needed HW bits.
From Mikhael, Remove unused struct field
From Saeed, Cleanup W=1 prototype warning
From Zheng, Esw related cleanup
From Tariq, User order-0 page allocation for EQs
* 'mlx5-next' of git://git.kernel.org/pub/scm/linux/kernel/git/mellanox/linux:
net/mlx5: Implement sriov_get_vf_total_msix/count() callbacks
net/mlx5: Dynamically assign MSI-X vectors count
net/mlx5: Add dynamic MSI-X capabilities bits
PCI/IOV: Add sysfs MSI-X vector assignment interface
net/mlx5: Use order-0 allocations for EQs
net/mlx5: Add IFC bits needed for single FDB mode
net/mlx5: E-Switch, Refactor send to vport to be more generic
RDMA/mlx5: Use representor E-Switch when getting netdev and metadata
net/mlx5: E-Switch, Add eswitch pointer to each representor
net/mlx5: E-Switch, Add match on vhca id to default send rules
net/mlx5: Remove unused mlx5_core_health member recover_work
net/mlx5: simplify the return expression of mlx5_esw_offloads_pair()
net/mlx5: Cleanup prototype warning
====================
Link: https://lore.kernel.org/r/20210409200704.10886-1-saeed@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
A device supports 128 rate limiters. A static table allocation consumes
8KB of memory even when rate is not configured.
Instead, allocate the table when at least one rate is configured.
Signed-off-by: Parav Pandit <parav@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
When switching modes between legacy and switchdev and back, do not
reload ethernet interfaces. just change the profile from nic profile
to uplink rep profile in switchdev mode.
Signed-off-by: Roi Dayan <roid@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
We re-use the native NIC port net device instance for the Uplink
representor, and the devlink port.
When changing profiles we reset the mlx5e priv but we should still
use the devlink port so move it to mlx5e resources.
Signed-off-by: Roi Dayan <roid@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
This is to separate between resources attributes and other
attributes we will want to use.
Signed-off-by: Roi Dayan <roid@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Currently we are allocating high-order page for EQs. In case of
fragmented system, VF hot remove/add in VMs for example, there isn't
enough contiguous memory for EQs allocation, which results in crashing
of the VM.
Therefore, use order-0 fragments for the EQ allocations instead.
Performance tests:
ConnectX-5 100Gbps, CPU: Intel(R) Xeon(R) CPU E5-2697 v3 @ 2.60GHz
Performance tests show no sensible degradation.
Signed-off-by: Tariq Toukan <tariqt@nvidia.com>
Signed-off-by: Shay Drory <shayd@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
The code related to health->recover_work was removed in
commit 63cbc552ee ("net/mlx5: Handle SW reset of FW in error flow")
Fix struct mlx5_core_health accordingly.
Signed-off-by: Mikhael Goikhman <migo@nvidia.com>
Reviewed-by: Tariq Toukan <tariqt@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
mlx5_is_roce_enabled returns the devlink RoCE init value, therefore it
should be used only when driver is loaded. Instead we just need to read
the roce_en field.
In addition, rename mlx5_is_roce_enabled to mlx5_is_roce_init_enabled.
Fixes: 7a58779edd ("IB/mlx5: Improve query port for representor port")
Link: https://lore.kernel.org/r/20210304124517.1100608-2-leon@kernel.org
Signed-off-by: Maor Gottlieb <maorg@nvidia.com>
Signed-off-by: Leon Romanovsky <leonro@nvidia.com>
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
- Driver updates and bug fixes: siw, hns, bnxt_re, mlx5, efa
- Significant rework in rxe to get it ready to have XRC support added
- Several rts bug fixes
- Big series to get to 'make W=1' cleanness, primarily updating kdocs
- Support for creating a RDMA MR from a DMABUF fd to allow PCI peer to
peer transfers to GPU VRAM
- Device disassociation now works properly with umad
- Work to support more than 255 ports on a RDMA device
- Further support for the new HNS HIP09 hardware
- Coding style cleanups: comma to semicolon, unneded semicolon/blank
lines, remove 'h' printk format, don't check for NULL before kfree,
use true/false for bool.
-----BEGIN PGP SIGNATURE-----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=Z4cZ
-----END PGP SIGNATURE-----
Merge tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rdma/rdma
Pull rdma updates from Jason Gunthorpe:
"This is quite a small cycle, if not for Lee's 70 patches cleaning the
kdocs it would be well below typical for patch count.
Most of the interesting work here was in the HNS and rxe drivers which
got fairly major internal changes.
Summary:
- Driver updates and bug fixes: siw, hns, bnxt_re, mlx5, efa
- Significant rework in rxe to get it ready to have XRC support added
- Several rts bug fixes
- Big series to get to 'make W=1' cleanness, primarily updating kdocs
- Support for creating a RDMA MR from a DMABUF fd to allow PCI peer
to peer transfers to GPU VRAM
- Device disassociation now works properly with umad
- Work to support more than 255 ports on a RDMA device
- Further support for the new HNS HIP09 hardware
- Coding style cleanups: comma to semicolon, unneded semicolon/blank
lines, remove 'h' printk format, don't check for NULL before kfree,
use true/false for bool"
* tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rdma/rdma: (205 commits)
RDMA/rtrs-srv: Do not pass a valid pointer to PTR_ERR()
RDMA/srp: Fix support for unpopulated and unbalanced NUMA nodes
RDMA/mlx5: Fail QP creation if the device can not support the CQE TS
RDMA/mlx5: Allow CQ creation without attached EQs
RDMA/rtrs-srv-sysfs: fix missing put_device
RDMA/rtrs-srv: fix memory leak by missing kobject free
RDMA/rtrs: Only allow addition of path to an already established session
RDMA/rtrs-srv: Fix stack-out-of-bounds
RDMA/rxe: Remove unused pkt->offset
RDMA/ucma: Fix use-after-free bug in ucma_create_uevent
RDMA/core: Fix kernel doc warnings for ib_port_immutable_read()
RDMA/qedr: Use true and false for bool variable
RDMA/hns: Adjust definition of FRMR fields
RDMA/hns: Refactor process of posting CMDQ
RDMA/hns: Adjust fields and variables about CMDQ tail/head
RDMA/hns: Remove redundant operations on CMDQ
RDMA/hns: Fixes missing error code of CMDQ
RDMA/hns: Remove unused member and variable of CMDQ
RDMA/ipoib: Remove racy Subnet Manager sendonly join checks
RDMA/mlx5: Support 400Gbps IB rate in mlx5 driver
...
-----BEGIN PGP SIGNATURE-----
iQFSBAABCAA8FiEEq68RxlopcLEwq+PEeb4+QwBBGIYFAmAppPgeHHRvcnZhbGRz
QGxpbnV4LWZvdW5kYXRpb24ub3JnAAoJEHm+PkMAQRiGeXYH/imZPBd4A1jIMehN
5HV2A53Z+MXmmaMuGj9X1KV6vsf55/xB+IhOoFdtRAIsO8c2yYSCO8i4+4R0XfYA
+/YFJeq672rojQnmh6XbpR8dugaAV7CUHy6n7KDsyvtT6EOCpwFSwkOb4X3tBRX6
TlYgm2d/xgV/wRHSgLVugK0MdFCLMAnyb7mkPfar9QrMgG1BiDKLq07xmwnS23On
TkqpJ9yZ/rJpUrrUqQYPShSO/FmA+fSfWs0CDv7EIrJ40LUScD6PZxSHWTIHtjLk
E4jFda6wuqLRVWsBwaBzUIdD0zk7X5quHRzEpbC5ga16SK6yrWvE5YJJXCguIEuZ
f3FMRYs=
=CAjn
-----END PGP SIGNATURE-----
Merge tag 'v5.11' into rdma.git for-next
Linux 5.11
Merged to resolve conflicts with RDMA rc commits
- drivers/infiniband/sw/rxe/rxe_net.c
The final logic is to call rxe_get_dev_from_net() again with the master
netdev if the packet was rx'd on a vlan. To keep the elimination of the
local variables requires a trivial edit to the code in -rc
Link: https://lore.kernel.org/r/20210210131542.215ea67c@canb.auug.org.au
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
Saeed Mahameed says:
====================
pull-request: mlx5-next 2021-02-16
The patches in this pr are already submitted and reviewed through the
netdev and rdma mailing lists.
The series includes mlx5 HW bits and definitions for mlx5 real time clock
translation and handling in the mlx5 driver clock module to enable and
support such mode [1]
[1] https://patchwork.kernel.org/project/netdevbpf/patch/20210212223042.449816-7-saeed@kernel.org/
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Internal timer mode (SW clock) requires some PTP clock related metadata
structs. Real time mode (HW clock) will not need these metadata structs.
This separation emphasize the different interfaces for HW clock and SW
clock.
Signed-off-by: Eran Ben Elisha <eranbe@mellanox.com>
Signed-off-by: Aya Levin <ayal@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Add needed structure layouts and defines for MTUTC (Management UTC)
register. MTUTC will be used for cyc2time HW translation.
In addition, add cyc2time modify capability bit and init segment HCA
real time address.
Finally, add capability bits indicating which time-stamping format is
supported per SQ and RQ. Add ts_format in the queue's context layout to
allow configuration.
Signed-off-by: Eran Ben Elisha <eranbe@mellanox.com>
Signed-off-by: Aya Levin <ayal@nvidia.com>
Reviewed-by: Moshe Shemesh <moshe@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Device list is not stored in mlx5_priv anymore, so delete it as it's not
used.
Signed-off-by: Leon Romanovsky <leonro@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Cleanup the synchronize_srcu() from the ODP flow as it was found to be a
very heavy time consumer as part of dereg_mr.
For example de-registration of 10000 ODP MRs each with size of 2M hugepage
took 19.6 sec comparing de-registration of same number of non ODP MRs that
took 172 ms.
The new locking scheme uses the wait_event() mechanism which follows the
use count of the MR instead of using synchronize_srcu().
By that change, the time required for the above test took 95 ms which is
even better than the non ODP flow.
Once fully dropped the srcu usage, had to come with a lock to protect the
XA access.
As part of using the above mechanism we could also clean the
num_deferred_work stuff and follow the use count instead.
Link: https://lore.kernel.org/r/20210202071309.2057998-1-leon@kernel.org
Signed-off-by: Yishai Hadas <yishaih@nvidia.com>
Signed-off-by: Leon Romanovsky <leonro@nvidia.com>
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
mlx5_port_caps are RDMA specific capabilities. These are not used by the
mlx5_core_device at all. Move them to mlx5_ib_dev where it is used and
reduce the scope of it to multiple drivers.
Link: https://lore.kernel.org/r/20210203130133.4057329-2-leon@kernel.org
Signed-off-by: Parav Pandit <parav@nvidia.com>
Signed-off-by: Leon Romanovsky <leonro@nvidia.com>
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
drivers/net/can/dev.c
b552766c87 ("can: dev: prevent potential information leak in can_fill_info()")
3e77f70e73 ("can: dev: move driver related infrastructure into separate subdir")
0a042c6ec9 ("can: dev: move netlink related code into seperate file")
Code move.
drivers/net/ethernet/mellanox/mlx5/core/en_ethtool.c
57ac4a31c4 ("net/mlx5e: Correctly handle changing the number of queues when the interface is down")
214baf2287 ("net/mlx5e: Support HTB offload")
Adjacent code changes
net/switchdev/switchdev.c
20776b465c ("net: switchdev: don't set port_obj_info->handled true when -EOPNOTSUPP")
ffb68fc58e ("net: switchdev: remove the transaction structure from port object notifiers")
bae33f2b5a ("net: switchdev: remove the transaction structure from port attributes")
Transaction parameter gets dropped otherwise keep the fix.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Parav Pandit Says:
=================
This patchset introduces support for mlx5 subfunction (SF).
A subfunction is a lightweight function that has a parent PCI function on
which it is deployed. mlx5 subfunction has its own function capabilities
and its own resources. This means a subfunction has its own dedicated
queues(txq, rxq, cq, eq). These queues are neither shared nor stolen from
the parent PCI function.
When subfunction is RDMA capable, it has its own QP1, GID table and rdma
resources neither shared nor stolen from the parent PCI function.
A subfunction has dedicated window in PCI BAR space that is not shared
with the other subfunctions or parent PCI function. This ensures that all
class devices of the subfunction accesses only assigned PCI BAR space.
A Subfunction supports eswitch representation through which it supports tc
offloads. User must configure eswitch to send/receive packets from/to
subfunction port.
Subfunctions share PCI level resources such as PCI MSI-X IRQs with
their other subfunctions and/or with its parent PCI function.
Patch summary:
--------------
Patch 1 to 4 prepares devlink
patch 5 to 7 mlx5 adds SF device support
Patch 8 to 11 mlx5 adds SF devlink port support
Patch 12 and 14 adds documentation
Patch-1 prepares code to handle multiple port function attributes
Patch-2 introduces devlink pcisf port flavour similar to pcipf and pcivf
Patch-3 adds port add and delete driver callbacks
Patch-4 adds port function state get and set callbacks
Patch-5 mlx5 vhca event notifier support to distribute subfunction
state change notification
Patch-6 adds SF auxiliary device
Patch-7 adds SF auxiliary driver
Patch-8 prepares eswitch to handler SF vport
Patch-9 adds eswitch helpers to add/remove SF vport
Patch-10 implements devlink port add/del callbacks
Patch-11 implements devlink port function get/set callbacks
Patch-12 to 14 adds documentation
Patch-12 added mlx5 port function documentation
Patch-13 adds subfunction documentation
Patch-14 adds mlx5 subfunction documentation
Subfunction support is discussed in detail in RFC [1] and [2].
RFC [1] and extension [2] describes requirements, design and proposed
plumbing using devlink, auxiliary bus and sysfs for systemd/udev
support. Functionality of this patchset is best explained using real
examples further below.
overview:
--------
A subfunction can be created and deleted by a user using devlink port
add/delete interface.
A subfunction can be configured using devlink port function attribute
before its activated.
When a subfunction is activated, it results in an auxiliary device on
the host PCI device where it is deployed. A driver binds to the
auxiliary device that further creates supported class devices.
example subfunction usage sequence:
-----------------------------------
Change device to switchdev mode:
$ devlink dev eswitch set pci/0000:06:00.0 mode switchdev
Add a devlink port of subfunction flavour:
$ devlink port add pci/0000:06:00.0 flavour pcisf pfnum 0 sfnum 88
Configure mac address of the port function:
$ devlink port function set ens2f0npf0sf88 hw_addr 00:00:00:00:88:88
Now activate the function:
$ devlink port function set ens2f0npf0sf88 state active
Now use the auxiliary device and class devices:
$ devlink dev show
pci/0000:06:00.0
auxiliary/mlx5_core.sf.4
$ ip link show
127: ens2f0np0: <BROADCAST,MULTICAST> mtu 1500 qdisc noop state DOWN mode DEFAULT group default qlen 1000
link/ether 24:8a:07:b3:d1:12 brd ff:ff:ff:ff:ff:ff
altname enp6s0f0np0
129: p0sf88: <BROADCAST,MULTICAST> mtu 1500 qdisc noop state DOWN mode DEFAULT group default qlen 1000
link/ether 00:00:00:00:88:88 brd ff:ff:ff:ff:ff:ff
$ rdma dev show
43: rdmap6s0f0: node_type ca fw 16.29.0550 node_guid 248a:0703:00b3:d112 sys_image_guid 248a:0703:00b3:d112
44: mlx5_0: node_type ca fw 16.29.0550 node_guid 0000:00ff:fe00:8888 sys_image_guid 248a:0703:00b3:d112
After use inactivate the function:
$ devlink port function set ens2f0npf0sf88 state inactive
Now delete the subfunction port:
$ devlink port del ens2f0npf0sf88
[1] https://lore.kernel.org/netdev/20200519092258.GF4655@nanopsycho/
[2] https://marc.info/?l=linux-netdev&m=158555928517777&w=2
=================
-----BEGIN PGP SIGNATURE-----
iQEzBAABCAAdFiEEGhZs6bAKwk/OTgTpSD+KveBX+j4FAmALKDwACgkQSD+KveBX
+j7qjQf6A1moPhhIlXROCzaJUjlAj2U291LWBveU+I6na6fjYjAAWHYwfv0YKQpo
Qb0NRt+9abgEpGidc4hOwIJKhK+vlWrQuehRt83aAfAwaN3OEeGuNllniWo821Hj
sNiJfSC/DslOlQSxKLsAs3Fduy/sV3GN9Zv7hEwOFgEr5QvB2c6H1XiypVP2Ecsd
ZXC3SuEWxIoRtfXEkTkJne9LNoiDChlvT1FR/z75h8HUBdAOjzBTQzBbM+8M4Msw
8aKUPya3FMRAPWsOgPhkpU0xTtH2Mi7MC9TlwiWmrK4Q3uvesIav8pVf7r3GNAZA
sipIZ4gP0M5SiCaZa8rIBpTXBHxmvg==
=jEG4
-----END PGP SIGNATURE-----
Merge tag 'mlx5-updates-2021-01-13' of git://git.kernel.org/pub/scm/linux/kernel/git/saeed/linux
Saeed Mahameed says:
====================
mlx5 subfunction support
Parav Pandit says:
This patchset introduces support for mlx5 subfunction (SF).
A subfunction is a lightweight function that has a parent PCI function on
which it is deployed. mlx5 subfunction has its own function capabilities
and its own resources. This means a subfunction has its own dedicated
queues(txq, rxq, cq, eq). These queues are neither shared nor stolen from
the parent PCI function.
When subfunction is RDMA capable, it has its own QP1, GID table and rdma
resources neither shared nor stolen from the parent PCI function.
A subfunction has dedicated window in PCI BAR space that is not shared
with the other subfunctions or parent PCI function. This ensures that all
class devices of the subfunction accesses only assigned PCI BAR space.
A Subfunction supports eswitch representation through which it supports tc
offloads. User must configure eswitch to send/receive packets from/to
subfunction port.
Subfunctions share PCI level resources such as PCI MSI-X IRQs with
their other subfunctions and/or with its parent PCI function.
Subfunction support is discussed in detail in RFC [1] and [2].
RFC [1] and extension [2] describes requirements, design and proposed
plumbing using devlink, auxiliary bus and sysfs for systemd/udev
support. Functionality of this patchset is best explained using real
examples further below.
overview:
--------
A subfunction can be created and deleted by a user using devlink port
add/delete interface.
A subfunction can be configured using devlink port function attribute
before its activated.
When a subfunction is activated, it results in an auxiliary device on
the host PCI device where it is deployed. A driver binds to the
auxiliary device that further creates supported class devices.
example subfunction usage sequence:
-----------------------------------
Change device to switchdev mode:
$ devlink dev eswitch set pci/0000:06:00.0 mode switchdev
Add a devlink port of subfunction flavour:
$ devlink port add pci/0000:06:00.0 flavour pcisf pfnum 0 sfnum 88
Configure mac address of the port function:
$ devlink port function set ens2f0npf0sf88 hw_addr 00:00:00:00:88:88
Now activate the function:
$ devlink port function set ens2f0npf0sf88 state active
Now use the auxiliary device and class devices:
$ devlink dev show
pci/0000:06:00.0
auxiliary/mlx5_core.sf.4
$ ip link show
127: ens2f0np0: <BROADCAST,MULTICAST> mtu 1500 qdisc noop state DOWN mode DEFAULT group default qlen 1000
link/ether 24:8a:07:b3:d1:12 brd ff:ff:ff:ff:ff:ff
altname enp6s0f0np0
129: p0sf88: <BROADCAST,MULTICAST> mtu 1500 qdisc noop state DOWN mode DEFAULT group default qlen 1000
link/ether 00:00:00:00:88:88 brd ff:ff:ff:ff:ff:ff
$ rdma dev show
43: rdmap6s0f0: node_type ca fw 16.29.0550 node_guid 248a:0703:00b3:d112 sys_image_guid 248a:0703:00b3:d112
44: mlx5_0: node_type ca fw 16.29.0550 node_guid 0000:00ff:fe00:8888 sys_image_guid 248a:0703:00b3:d112
After use inactivate the function:
$ devlink port function set ens2f0npf0sf88 state inactive
Now delete the subfunction port:
$ devlink port del ens2f0npf0sf88
[1] https://lore.kernel.org/netdev/20200519092258.GF4655@nanopsycho/
[2] https://marc.info/?l=linux-netdev&m=158555928517777&w=2
=================
* tag 'mlx5-updates-2021-01-13' of git://git.kernel.org/pub/scm/linux/kernel/git/saeed/linux:
net/mlx5: Add devlink subfunction port documentation
devlink: Extend devlink port documentation for subfunctions
devlink: Add devlink port documentation
net/mlx5: SF, Port function state change support
net/mlx5: SF, Add port add delete functionality
net/mlx5: E-switch, Add eswitch helpers for SF vport
net/mlx5: E-switch, Prepare eswitch to handle SF vport
net/mlx5: SF, Add auxiliary device driver
net/mlx5: SF, Add auxiliary device support
net/mlx5: Introduce vhca state event notifier
devlink: Support get and set state of port function
devlink: Support add and delete devlink port
devlink: Introduce PCI SF port flavour and port attribute
devlink: Prepare code to fill multiple port function attributes
====================
Link: https://lore.kernel.org/r/20210122193658.282884-1-saeed@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
In order to allow mlx5 core driver to trigger synchronous operations to
its consumers, add a blocking events handler. Add wrappers to
blocking_notifier_[call_chain/chain_register/chain_unregister]. Add trap
callback for action set and notify about this change. Following patches
in the set add a listener for this event.
Signed-off-by: Aya Levin <ayal@nvidia.com>
Reviewed-by: Tariq Toukan <tariqt@nvidia.com>
Signed-off-by: Tariq Toukan <tariqt@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
To handle SF port management outside of the eswitch as independent
software layer, introduce eswitch notifier APIs so that mlx5 upper
layer who wish to support sf port management in switchdev mode can
perform its task whenever eswitch mode is set to switchdev or before
eswitch is disabled.
Initialize sf port table on such eswitch event.
Add SF port add and delete functionality in switchdev mode.
Destroy all SF ports when eswitch is disabled.
Expose SF port add and delete to user via devlink commands.
$ devlink dev eswitch set pci/0000:06:00.0 mode switchdev
$ devlink port show
pci/0000:06:00.0/65535: type eth netdev ens2f0np0 flavour physical port 0 splittable false
$ devlink port add pci/0000:06:00.0 flavour pcisf pfnum 0 sfnum 88
pci/0000:06:00.0/32768: type eth netdev eth6 flavour pcisf controller 0 pfnum 0 sfnum 88 external false splittable false
function:
hw_addr 00:00:00:00:00:00 state inactive opstate detached
$ devlink port show ens2f0npf0sf88
pci/0000:06:00.0/32768: type eth netdev ens2f0npf0sf88 flavour pcisf controller 0 pfnum 0 sfnum 88 external false splittable false
function:
hw_addr 00:00:00:00:00:00 state inactive opstate detached
or by its unique port index:
$ devlink port show pci/0000:06:00.0/32768
pci/0000:06:00.0/32768: type eth netdev ens2f0npf0sf88 flavour pcisf controller 0 pfnum 0 sfnum 88 external false splittable false
function:
hw_addr 00:00:00:00:00:00 state inactive opstate detached
$ devlink port show ens2f0npf0sf88 -jp
{
"port": {
"pci/0000:06:00.0/32768": {
"type": "eth",
"netdev": "ens2f0npf0sf88",
"flavour": "pcisf",
"controller": 0,
"pfnum": 0,
"sfnum": 88,
"external": false,
"splittable": false,
"function": {
"hw_addr": "00:00:00:00:00:00",
"state": "inactive",
"opstate": "detached"
}
}
}
}
Signed-off-by: Parav Pandit <parav@nvidia.com>
Reviewed-by: Vu Pham <vuhuong@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Add auxiliary device driver for mlx5 subfunction auxiliary device.
A mlx5 subfunction is similar to PCI PF and VF. For a subfunction
an auxiliary device is created.
As a result, when mlx5 SF auxiliary device binds to the driver,
its netdev and rdma device are created, they appear as
$ ls -l /sys/bus/auxiliary/devices/
mlx5_core.sf.4 -> ../../../devices/pci0000:00/0000:00:03.0/0000:06:00.0/mlx5_core.sf.4
$ ls -l /sys/class/net/eth1/device
/sys/class/net/eth1/device -> ../../../mlx5_core.sf.4
$ cat /sys/bus/auxiliary/devices/mlx5_core.sf.4/sfnum
88
$ devlink dev show
pci/0000:06:00.0
auxiliary/mlx5_core.sf.4
$ devlink port show auxiliary/mlx5_core.sf.4/1
auxiliary/mlx5_core.sf.4/1: type eth netdev p0sf88 flavour virtual port 0 splittable false
$ rdma link show mlx5_0/1
link mlx5_0/1 state ACTIVE physical_state LINK_UP netdev p0sf88
$ rdma dev show
8: rocep6s0f1: node_type ca fw 16.29.0550 node_guid 248a:0703:00b3:d113 sys_image_guid 248a:0703:00b3:d112
13: mlx5_0: node_type ca fw 16.29.0550 node_guid 0000:00ff:fe00:8888 sys_image_guid 248a:0703:00b3:d112
In future, devlink device instance name will adapt to have sfnum
annotation using either an alias or as devlink instance name described
in RFC [1].
[1] https://lore.kernel.org/netdev/20200519092258.GF4655@nanopsycho/
Signed-off-by: Parav Pandit <parav@nvidia.com>
Reviewed-by: Vu Pham <vuhuong@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Introduce API to add and delete an auxiliary device for an SF.
Each SF has its own dedicated window in the PCI BAR 2.
SF device is similar to PCI PF and VF that supports multiple class of
devices such as net, rdma and vdpa.
SF device will be added or removed in subsequent patch during SF
devlink port function state change command.
A subfunction device exposes user supplied subfunction number which will
be further used by systemd/udev to have deterministic name for its
netdevice and rdma device.
An mlx5 subfunction auxiliary device example:
$ devlink dev eswitch set pci/0000:06:00.0 mode switchdev
$ devlink port show
pci/0000:06:00.0/65535: type eth netdev ens2f0np0 flavour physical port 0 splittable false
$ devlink port add pci/0000:06:00.0 flavour pcisf pfnum 0 sfnum 88
pci/0000:08:00.0/32768: type eth netdev eth6 flavour pcisf controller 0 pfnum 0 sfnum 88 external false splittable false
function:
hw_addr 00:00:00:00:00:00 state inactive opstate detached
$ devlink port show ens2f0npf0sf88
pci/0000:06:00.0/32768: type eth netdev ens2f0npf0sf88 flavour pcisf controller 0 pfnum 0 sfnum 88 external false splittable false
function:
hw_addr 00:00:00:00:88:88 state inactive opstate detached
$ devlink port function set ens2f0npf0sf88 hw_addr 00:00:00:00:88:88 state active
On activation,
$ ls -l /sys/bus/auxiliary/devices/
mlx5_core.sf.4 -> ../../../devices/pci0000:00/0000:00:03.0/0000:06:00.0/mlx5_core.sf.4
$ cat /sys/bus/auxiliary/devices/mlx5_core.sf.4/sfnum
88
Signed-off-by: Parav Pandit <parav@nvidia.com>
Reviewed-by: Vu Pham <vuhuong@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
vhca state events indicates change in the state of the vhca that may
occur due to a SF allocation, deallocation or enabling/disabling the
SF HCA.
Introduce vhca state event handler which will be used by SF devlink
port manager and SF hardware id allocator in subsequent patches
to act on the event.
This enables single entity to subscribe, query and rearm the event
for a function.
Signed-off-by: Parav Pandit <parav@nvidia.com>
Reviewed-by: Vu Pham <vuhuong@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
This reverts commit fbdd0049d9.
Due to commit in fixes tag, netdevice events were received only in one net
namespace of mlx5_core_dev. Due to this when netdevice events arrive in
net namespace other than net namespace of mlx5_core_dev, they are missed.
This results in empty GID table due to RDMA device being detached from its
net device.
Hence, revert back to receive netdevice events in all net namespaces to
restore back RDMA functionality in non init_net net namespace. The
deadlock will have to be addressed in another patch.
Fixes: fbdd0049d9 ("RDMA/mlx5: Fix devlink deadlock on net namespace deletion")
Link: https://lore.kernel.org/r/20210117092633.10690-1-leon@kernel.org
Signed-off-by: Parav Pandit <parav@nvidia.com>
Signed-off-by: Leon Romanovsky <leonro@nvidia.com>
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
Saeed Mahameed says:
====================
mlx5-next auxbus support
This pull request is targeting net-next and rdma-next branches.
This series provides mlx5 support for auxiliary bus devices.
It starts with a merge commit of tag 'auxbus-5.11-rc1' from
gregkh/driver-core into mlx5-next, then the mlx5 patches that will convert
mlx5 ulp devices (netdev, rdma, vdpa) to use the proper auxbus
infrastructure instead of the internal mlx5 device and interface management
implementation, which Leon is deleting at the end of this patchset.
Link: https://lore.kernel.org/alsa-devel/20201026111849.1035786-1-leon@kernel.org/
Thanks to everyone for the joint effort !
* 'mlx5-next' of git://git.kernel.org/pub/scm/linux/kernel/git/mellanox/linux:
RDMA/mlx5: Remove IB representors dead code
net/mlx5: Simplify eswitch mode check
net/mlx5: Delete custom device management logic
RDMA/mlx5: Convert mlx5_ib to use auxiliary bus
net/mlx5e: Connect ethernet part to auxiliary bus
vdpa/mlx5: Connect mlx5_vdpa to auxiliary bus
net/mlx5: Register mlx5 devices to auxiliary virtual bus
vdpa/mlx5: Make hardware definitions visible to all mlx5 devices
net/mlx5_core: Clean driver version and name
net/mlx5: Properly convey driver version to firmware
driver core: auxiliary bus: minor coding style tweaks
driver core: auxiliary bus: make remove function return void
driver core: auxiliary bus: move slab.h from include file
Add auxiliary bus support
====================
Link: https://lore.kernel.org/r/20201207053349.402772-1-saeed@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
After conversion to use auxiliary bus, all custom device management is
not needed anymore, delete it.
Signed-off-by: Leon Romanovsky <leonro@nvidia.com>
Remove exposed driver version as it was done in other drivers,
so module version will work correctly by displaying the kernel
version for which it is compiled.
And move mlx5_core module name to general include, so auxiliary drivers
will be able to use it as a basis for a name in their device ID tables.
Reviewed-by: Parav Pandit <parav@nvidia.com>
Reviewed-by: Roi Dayan <roid@nvidia.com>
Signed-off-by: Leon Romanovsky <leonro@nvidia.com>
Low level mlx5 updates required by both netdev and rdma trees:
net/mlx5: Treat host PF vport as other (non eswitch manager) vport
net/mlx5: Enable host PF HCA after eswitch is initialized
net/mlx5: Rename peer_pf to host_pf
net/mlx5: Make API mlx5_core_is_ecpf accept const pointer
net/mlx5: Export steering related functions
net/mlx5: Expose other function ifc bits
net/mlx5: Expose IP-in-IP TX and RX capability bits
net/mlx5: Update the hardware interface definition for vhca state
net/mlx5: Update the list of the PCI supported devices
net/mlx5: Avoid exposing driver internal command helpers
net/mlx5: Add ts_cqe_to_dest_cqn related bits
net/mlx5: Add misc4 to mlx5_ifc_fte_match_param_bits
net/mlx5: Check dr mask size against mlx5_match_param size
net/mlx5: Add sampler destination type
net/mlx5: Add sample offload hardware bits and structures
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
-----BEGIN PGP SIGNATURE-----
iQEzBAABCAAdFiEEGhZs6bAKwk/OTgTpSD+KveBX+j4FAl/IOZcACgkQSD+KveBX
+j4J8wgAuxwflrYrbCWXV7LE08J7T7ZHRDE+jEbaZ0Zp9mOsYDDpcifpKwy2EVRf
RKcpMYh/GzAljmEpeWIAlMxmlpXhKWXTDruWCx73r1jvdXf/RU24/zQHa6BjeiDo
rMB8bgiW4a66+z4LcN/U6ahbVM5gScBNEt2sS1OIi9ZInngGVo9FgfhYMpERPNcH
3+mcHulCnGBNbbLwoTllOcgbxexn+xoByukg5Z0ddBJp007DMjzBIWDpDS0y2HaT
jGo1LYONgRc3zoGVmdeu9F+tSsWBIgsaiyGxKj1T/8sZUaNz2TKj9VOiYIj9BLff
cp6GRc88k7HWA4tImSHQiLbK6cx+yA==
=mjvI
-----END PGP SIGNATURE-----
Merge tag 'mlx5-next-2020-12-02' of git://git.kernel.org/pub/scm/linux/kernel/git/mellanox/linux
Saeed Mahameed says:
====================
mlx5-next-2020-12-02
Low level mlx5 updates required by both netdev and rdma trees.
* tag 'mlx5-next-2020-12-02' of git://git.kernel.org/pub/scm/linux/kernel/git/mellanox/linux:
net/mlx5: Treat host PF vport as other (non eswitch manager) vport
net/mlx5: Enable host PF HCA after eswitch is initialized
net/mlx5: Rename peer_pf to host_pf
net/mlx5: Make API mlx5_core_is_ecpf accept const pointer
net/mlx5: Export steering related functions
net/mlx5: Expose other function ifc bits
net/mlx5: Expose IP-in-IP TX and RX capability bits
net/mlx5: Update the hardware interface definition for vhca state
net/mlx5: Update the list of the PCI supported devices
net/mlx5: Avoid exposing driver internal command helpers
net/mlx5: Add ts_cqe_to_dest_cqn related bits
net/mlx5: Add misc4 to mlx5_ifc_fte_match_param_bits
net/mlx5: Check dr mask size against mlx5_match_param size
net/mlx5: Add sampler destination type
net/mlx5: Add sample offload hardware bits and structures
====================
Link: https://lore.kernel.org/r/20201203011010.213440-1-saeedm@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
To match the hardware spec, rename peer_pf to host_pf.
Signed-off-by: Parav Pandit <parav@nvidia.com>
Reviewed-by: Bodong Wang <bodong@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Subsequent patch implements helper API which has mlx5_core_dev
as const pointer, make its caller API too const *.
Signed-off-by: Parav Pandit <parav@nvidia.com>
Reviewed-by: Bodong Wang <bodong@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
mlx5 command init and cleanup routines are internal to mlx5_core driver.
Hence, avoid exporting them and move their definition to mlx5_core
driver's internal file mlx5_core.h
Signed-off-by: Parav Pandit <parav@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Shay Drory