Alexey removed kernel side support for requests, and the
only thing we do for replies is log a message if something
doesn't look right.
As Alexey's comment indicates, this belongs in userspace (if
anywhere), and thus we can safely just get rid of this code.
Signed-off-by: David S. Miller <davem@davemloft.net>
All handler->err() routines expect that we've done a pskb_may_pull()
test to make sure that IP header length + 8 bytes can be safely
pulled.
Reported-by: Hiroaki SHIMODA <shimoda.hiroaki@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
No longer needed, as the protocol handlers now all properly
propagate the redirect back into the routing code.
Signed-off-by: David S. Miller <davem@davemloft.net>
Pass in the SKB rather than just the IP addresses, so that policy
and other aspects can reside in ip_rt_redirect() rather then
icmp_redirect().
Signed-off-by: David S. Miller <davem@davemloft.net>
The specific destination is the host we direct unicast replies to.
Usually this is the original packet source address, but if we are
responding to a multicast or broadcast packet we have to use something
different.
Specifically we must use the source address we would use if we were to
send a packet to the unicast source of the original packet.
The routing cache precomputes this value, but we want to remove that
precomputation because it creates a hard dependency on the expensive
rpfilter source address validation which we'd like to make cheaper.
There are only three places where this matters:
1) ICMP replies.
2) pktinfo CMSG
3) IP options
Now there will be no real users of rt->rt_spec_dst and we can simply
remove it altogether.
Signed-off-by: David S. Miller <davem@davemloft.net>
Don't pretend that inet_protos[] and inet6_protos[] are hashes, thay
are just a straight arrays. Remove all unnecessary hash masking.
Document MAX_INET_PROTOS.
Use RAW_HTABLE_SIZE when appropriate.
Reported-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is zero point to this function.
It's only real substance is to perform an extremely outdated BSD4.2
ICMP check, which we can safely remove. If you really have a MTU
limited link being routed by a BSD4.2 derived system, here's a nickel
go buy yourself a real router.
The other actions of ip_rt_frag_needed(), checking and conditionally
updating the peer, are done by the per-protocol handlers of the ICMP
event.
TCP, UDP, et al. have a handler which will receive this event and
transmit it back into the associated route via dst_ops->update_pmtu().
This simplification is important, because it eliminates the one place
where we do not have a proper route context in which to make an
inetpeer lookup.
Signed-off-by: David S. Miller <davem@davemloft.net>
There's a lot of places that open-code rt{,6}_get_peer() only because
they want to set 'create' to one. So add an rt{,6}_get_peer_create()
for their sake.
There were also a few spots open-coding plain rt{,6}_get_peer() and
those are transformed here as well.
Signed-off-by: David S. Miller <davem@davemloft.net>
Standardize the net core ratelimited logging functions.
Coalesce formats, align arguments.
Change a printk then vprintk sequence to use printf extension %pV.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove all #inclusions of asm/system.h preparatory to splitting and killing
it. Performed with the following command:
perl -p -i -e 's!^#\s*include\s*<asm/system[.]h>.*\n!!' `grep -Irl '^#\s*include\s*<asm/system[.]h>' *`
Signed-off-by: David Howells <dhowells@redhat.com>
Add #define pr_fmt(fmt) as appropriate.
Add "IPv4: ", "TCP: ", and "IPsec: " to appropriate files.
Standardize on "UDPLite: " for appropriate uses.
Some prefixes were previously "UDPLITE: " and "UDP-Lite: ".
Add KBUILD_MODNAME ": " to icmp and gre.
Remove embedded prefixes as appropriate.
Add missing "\n" to pr_info in gre.c.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use a more current kernel messaging style.
Convert a printk block to print_hex_dump.
Coalesce formats, align arguments.
Use %s, __func__ instead of embedding function names.
Some messages that were prefixed with <foo>_close are
now prefixed with <foo>_fini. Some ah4 and esp messages
are now not prefixed with "ip ".
The intent of this patch is to later add something like
#define pr_fmt(fmt) "IPv4: " fmt.
to standardize the output messages.
Text size is trivially reduced. (x86-32 allyesconfig)
$ size net/ipv4/built-in.o*
text data bss dec hex filename
887888 31558 249696 1169142 11d6f6 net/ipv4/built-in.o.new
887934 31558 249800 1169292 11d78c net/ipv4/built-in.o.old
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
skb truesize currently accounts for sk_buff struct and part of skb head.
kmalloc() roundings are also ignored.
Considering that skb_shared_info is larger than sk_buff, its time to
take it into account for better memory accounting.
This patch introduces SKB_TRUESIZE(X) macro to centralize various
assumptions into a single place.
At skb alloc phase, we put skb_shared_info struct at the exact end of
skb head, to allow a better use of memory (lowering number of
reallocations), since kmalloc() gives us power-of-two memory blocks.
Unless SLUB/SLUB debug is active, both skb->head and skb_shared_info are
aligned to cache lines, as before.
Note: This patch might trigger performance regressions because of
misconfigured protocol stacks, hitting per socket or global memory
limits that were previously not reached. But its a necessary step for a
more accurate memory accounting.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
CC: Andi Kleen <ak@linux.intel.com>
CC: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
icmp_route_lookup() uses the wrong flow parameters if the reverse
session route lookup isn't used.
So do not commit to the re-decoded flow until we actually make a
final decision to use a real route saved in 'rt2'.
Reported-by: Florian Westphal <fw@strlen.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds IPPROTO_ICMP socket kind. It makes it possible to send
ICMP_ECHO messages and receive the corresponding ICMP_ECHOREPLY messages
without any special privileges. In other words, the patch makes it
possible to implement setuid-less and CAP_NET_RAW-less /bin/ping. In
order not to increase the kernel's attack surface, the new functionality
is disabled by default, but is enabled at bootup by supporting Linux
distributions, optionally with restriction to a group or a group range
(see below).
Similar functionality is implemented in Mac OS X:
http://www.manpagez.com/man/4/icmp/
A new ping socket is created with
socket(PF_INET, SOCK_DGRAM, PROT_ICMP)
Message identifiers (octets 4-5 of ICMP header) are interpreted as local
ports. Addresses are stored in struct sockaddr_in. No port numbers are
reserved for privileged processes, port 0 is reserved for API ("let the
kernel pick a free number"). There is no notion of remote ports, remote
port numbers provided by the user (e.g. in connect()) are ignored.
Data sent and received include ICMP headers. This is deliberate to:
1) Avoid the need to transport headers values like sequence numbers by
other means.
2) Make it easier to port existing programs using raw sockets.
ICMP headers given to send() are checked and sanitized. The type must be
ICMP_ECHO and the code must be zero (future extensions might relax this,
see below). The id is set to the number (local port) of the socket, the
checksum is always recomputed.
ICMP reply packets received from the network are demultiplexed according
to their id's, and are returned by recv() without any modifications.
IP header information and ICMP errors of those packets may be obtained
via ancillary data (IP_RECVTTL, IP_RETOPTS, and IP_RECVERR). ICMP source
quenches and redirects are reported as fake errors via the error queue
(IP_RECVERR); the next hop address for redirects is saved to ee_info (in
network order).
socket(2) is restricted to the group range specified in
"/proc/sys/net/ipv4/ping_group_range". It is "1 0" by default, meaning
that nobody (not even root) may create ping sockets. Setting it to "100
100" would grant permissions to the single group (to either make
/sbin/ping g+s and owned by this group or to grant permissions to the
"netadmins" group), "0 4294967295" would enable it for the world, "100
4294967295" would enable it for the users, but not daemons.
The existing code might be (in the unlikely case anyone needs it)
extended rather easily to handle other similar pairs of ICMP messages
(Timestamp/Reply, Information Request/Reply, Address Mask Request/Reply
etc.).
Userspace ping util & patch for it:
http://openwall.info/wiki/people/segoon/ping
For Openwall GNU/*/Linux it was the last step on the road to the
setuid-less distro. A revision of this patch (for RHEL5/OpenVZ kernels)
is in use in Owl-current, such as in the 2011/03/12 LiveCD ISOs:
http://mirrors.kernel.org/openwall/Owl/current/iso/
Initially this functionality was written by Pavel Kankovsky for
Linux 2.4.32, but unfortunately it was never made public.
All ping options (-b, -p, -Q, -R, -s, -t, -T, -M, -I), are tested with
the patch.
PATCH v3:
- switched to flowi4.
- minor changes to be consistent with raw sockets code.
PATCH v2:
- changed ping_debug() to pr_debug().
- removed CONFIG_IP_PING.
- removed ping_seq_fops.owner field (unused for procfs).
- switched to proc_net_fops_create().
- switched to %pK in seq_printf().
PATCH v1:
- fixed checksumming bug.
- CAP_NET_RAW may not create icmp sockets anymore.
RFC v2:
- minor cleanups.
- introduced sysctl'able group range to restrict socket(2).
Signed-off-by: Vasiliy Kulikov <segoon@openwall.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
On input packets, rt->rt_src always equals ip_hdr(skb)->saddr
Anything that mangles or otherwise changes the IP header must
relookup the route found at skb_rtable(). Therefore this
invariant must always hold true.
Signed-off-by: David S. Miller <davem@davemloft.net>
This way ip_output.c no longer needs rt->rt_{src,dst}.
We already have these keys sitting, ready and waiting, on the stack or
in a socket structure.
Signed-off-by: David S. Miller <davem@davemloft.net>
We lack proper synchronization to manipulate inet->opt ip_options
Problem is ip_make_skb() calls ip_setup_cork() and
ip_setup_cork() possibly makes a copy of ipc->opt (struct ip_options),
without any protection against another thread manipulating inet->opt.
Another thread can change inet->opt pointer and free old one under us.
Use RCU to protect inet->opt (changed to inet->inet_opt).
Instead of handling atomic refcounts, just copy ip_options when
necessary, to avoid cache line dirtying.
We cant insert an rcu_head in struct ip_options since its included in
skb->cb[], so this patch is large because I had to introduce a new
ip_options_rcu structure.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Cc: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add const qualifiers to structs iphdr, ipv6hdr and in6_addr pointers
where possible, to make code intention more obvious.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Create two sets of port member accessors, one set prefixed by fl4_*
and the other prefixed by fl6_*
This will let us to create AF optimal flow instances.
It will work because every context in which we access the ports,
we have to be fully aware of which AF the flowi is anyways.
Signed-off-by: David S. Miller <davem@davemloft.net>
I intend to turn struct flowi into a union of AF specific flowi
structs. There will be a common structure that each variant includes
first, much like struct sock_common.
This is the first step to move in that direction.
Signed-off-by: David S. Miller <davem@davemloft.net>
The only necessary parts are the src/dst addresses, the
interface indexes, the TOS, and the mark.
The rest is unnecessary bloat, which amounts to nearly
50 bytes on 64-bit.
Signed-off-by: David S. Miller <davem@davemloft.net>
The route lookup code in icmp_send() is slightly tricky as a result of
having to handle all of the requirements of RFC 4301 host relookups.
Pull the route resolution into a seperate function, so that the error
handling and route reference counting is hopefully easier to see and
contained wholly within this new routine.
Signed-off-by: David S. Miller <davem@davemloft.net>
Like metrics, the ICMP rate limiting bits are cached state about
a destination. So move it into the inet_peer entries.
If an inet_peer cannot be bound (the reason is memory allocation
failure or similar), the policy is to allow.
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the macros defined for the members of flowi to clean the code up.
Signed-off-by: Changli Gao <xiaosuo@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
otherwise xfrm_lookup will fail to find correct policy
Signed-off-by: Ulrich Weber <uweber@astaro.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When we test rt->fl.iif against zero, we're seeing if it's
an output or an input route.
Make that explicit with some helper functions.
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch removes the abstraction introduced by the union skb_shared_tx in
the shared skb data.
The access of the different union elements at several places led to some
confusion about accessing the shared tx_flags e.g. in skb_orphan_try().
http://marc.info/?l=linux-netdev&m=128084897415886&w=2
Signed-off-by: Oliver Hartkopp <socketcan@hartkopp.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
CodingStyle cleanups
EXPORT_SYMBOL should immediately follow the symbol declaration.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
remove useless union keyword in rtable, rt6_info and dn_route.
Since there is only one member in a union, the union keyword isn't useful.
Signed-off-by: Changli Gao <xiaosuo@gmail.com>
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
- rcu_read_lock() already held by caller
- use __in_dev_get_rcu() instead of in_dev_get() / in_dev_put()
- remove goto out;
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use low order bit of skb->_skb_dst to tell dst is not refcounted.
Change _skb_dst to _skb_refdst to make sure all uses are catched.
skb_dst() returns the dst, regardless of noref bit set or not, but
with a lockdep check to make sure a noref dst is not given if current
user is not rcu protected.
New skb_dst_set_noref() helper to set an notrefcounted dst on a skb.
(with lockdep check)
skb_dst_drop() drops a reference only if skb dst was refcounted.
skb_dst_force() helper is used to force a refcount on dst, when skb
is queued and not anymore RCU protected.
Use skb_dst_force() in __sk_add_backlog(), __dev_xmit_skb() if
!IFF_XMIT_DST_RELEASE or skb enqueued on qdisc queue, in
sock_queue_rcv_skb(), in __nf_queue().
Use skb_dst_force() in dev_requeue_skb().
Note: dst_use_noref() still dirties dst, we might transform it
later to do one dirtying per jiffies.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When ip_append() fails because of socket limit or memory shortage,
increment ICMP_MIB_OUTERRORS counter, so that "netstat -s" can report
these errors.
LANG=C netstat -s | grep "ICMP messages failed"
0 ICMP messages failed
For IPV6, implement ICMP6_MIB_OUTERRORS counter as well.
# grep Icmp6OutErrors /proc/net/dev_snmp6/*
/proc/net/dev_snmp6/eth0:Icmp6OutErrors 0
/proc/net/dev_snmp6/lo:Icmp6OutErrors 0
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
percpu.h is included by sched.h and module.h and thus ends up being
included when building most .c files. percpu.h includes slab.h which
in turn includes gfp.h making everything defined by the two files
universally available and complicating inclusion dependencies.
percpu.h -> slab.h dependency is about to be removed. Prepare for
this change by updating users of gfp and slab facilities include those
headers directly instead of assuming availability. As this conversion
needs to touch large number of source files, the following script is
used as the basis of conversion.
http://userweb.kernel.org/~tj/misc/slabh-sweep.py
The script does the followings.
* Scan files for gfp and slab usages and update includes such that
only the necessary includes are there. ie. if only gfp is used,
gfp.h, if slab is used, slab.h.
* When the script inserts a new include, it looks at the include
blocks and try to put the new include such that its order conforms
to its surrounding. It's put in the include block which contains
core kernel includes, in the same order that the rest are ordered -
alphabetical, Christmas tree, rev-Xmas-tree or at the end if there
doesn't seem to be any matching order.
* If the script can't find a place to put a new include (mostly
because the file doesn't have fitting include block), it prints out
an error message indicating which .h file needs to be added to the
file.
The conversion was done in the following steps.
1. The initial automatic conversion of all .c files updated slightly
over 4000 files, deleting around 700 includes and adding ~480 gfp.h
and ~3000 slab.h inclusions. The script emitted errors for ~400
files.
2. Each error was manually checked. Some didn't need the inclusion,
some needed manual addition while adding it to implementation .h or
embedding .c file was more appropriate for others. This step added
inclusions to around 150 files.
3. The script was run again and the output was compared to the edits
from #2 to make sure no file was left behind.
4. Several build tests were done and a couple of problems were fixed.
e.g. lib/decompress_*.c used malloc/free() wrappers around slab
APIs requiring slab.h to be added manually.
5. The script was run on all .h files but without automatically
editing them as sprinkling gfp.h and slab.h inclusions around .h
files could easily lead to inclusion dependency hell. Most gfp.h
inclusion directives were ignored as stuff from gfp.h was usually
wildly available and often used in preprocessor macros. Each
slab.h inclusion directive was examined and added manually as
necessary.
6. percpu.h was updated not to include slab.h.
7. Build test were done on the following configurations and failures
were fixed. CONFIG_GCOV_KERNEL was turned off for all tests (as my
distributed build env didn't work with gcov compiles) and a few
more options had to be turned off depending on archs to make things
build (like ipr on powerpc/64 which failed due to missing writeq).
* x86 and x86_64 UP and SMP allmodconfig and a custom test config.
* powerpc and powerpc64 SMP allmodconfig
* sparc and sparc64 SMP allmodconfig
* ia64 SMP allmodconfig
* s390 SMP allmodconfig
* alpha SMP allmodconfig
* um on x86_64 SMP allmodconfig
8. percpu.h modifications were reverted so that it could be applied as
a separate patch and serve as bisection point.
Given the fact that I had only a couple of failures from tests on step
6, I'm fairly confident about the coverage of this conversion patch.
If there is a breakage, it's likely to be something in one of the arch
headers which should be easily discoverable easily on most builds of
the specific arch.
Signed-off-by: Tejun Heo <tj@kernel.org>
Guess-its-ok-by: Christoph Lameter <cl@linux-foundation.org>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Lee Schermerhorn <Lee.Schermerhorn@hp.com>
We can avoid touching device refcount in icmp_send(),
using dev_get_by_index_rcu()
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We can make icmp messages tx completion callback a litle bit faster.
Setting SOCK_USE_WRITE_QUEUE sk flag tells sock_wfree() to
not call sk_write_space() on a socket we know no thread is posssibly
waiting for write space. (on per cpu kernel internal icmp sockets only)
This avoids the sock_def_write_space() call and
read_lock(&sk->sk_callback_lock)/read_unlock(&sk->sk_callback_lock) calls
as well.
We avoid three atomic ops.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove long removed "inet_protocol_base" declaration.
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Define three accessors to get/set dst attached to a skb
struct dst_entry *skb_dst(const struct sk_buff *skb)
void skb_dst_set(struct sk_buff *skb, struct dst_entry *dst)
void skb_dst_drop(struct sk_buff *skb)
This one should replace occurrences of :
dst_release(skb->dst)
skb->dst = NULL;
Delete skb->dst field
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Define skb_rtable(const struct sk_buff *skb) accessor to get rtable from skb
Delete skb->rtable field
Setting rtable is not allowed, just set dst instead as rtable is an alias.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Recently I had a kernel panic in icmp_send during a network namespace
cleanup. There were packets in the arp queue that failed to be sent
and we attempted to generate an ICMP host unreachable message, but
failed because icmp_sk_exit had already been called.
The network devices are removed from a network namespace and their
arp queues are flushed before we do attempt to shutdown subsystems
so this error should have been impossible.
It turns out icmp_init is using register_pernet_device instead
of register_pernet_subsys. Which resulted in icmp being shut down
while we still had the possibility of packets in flight, making
a nasty NULL pointer deference in interrupt context possible.
Changing this to register_pernet_subsys fixes the problem in
my testing.
Signed-off-by: Eric W. Biederman <ebiederm@aristanetworks.com>
Acked-by: Denis V. Lunev <den@openvz.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Instructions for time stamping outgoing packets are take from the
socket layer and later copied into the new skb.
Signed-off-by: Patrick Ohly <patrick.ohly@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pass netns to xfrm_lookup()/__xfrm_lookup(). For that pass netns
to flow_cache_lookup() and resolver callback.
Take it from socket or netdevice. Stub DECnet to init_net.
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We can reduce pressure on dst entry refcount that slowdown UDP transmit
path on SMP machines. This pressure is visible on RTP servers when
delivering content to mediagateways, especially big ones, handling
thousand of streams. Several cpus send UDP frames to the same
destination, hence use the same dst entry.
This patch makes ip_append_data() eventually steal the refcount its
callers had to take on the dst entry.
This doesnt avoid all refcounting, but still gives speedups on SMP,
on UDP/RAW transmit path
Signed-off-by: Eric Dumazet <dada1@cosmosbay.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Using NIPQUAD() with NIPQUAD_FMT, %d.%d.%d.%d or %u.%u.%u.%u
can be replaced with %pI4
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Clean up the various different email addresses of mine listed in the code
to a single current and valid address. As Dave says his network merges
for 2.6.28 are now done this seems a good point to send them in where
they won't risk disrupting real changes.
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some places, that deal with ICMP statistics already have where
to get a struct net from, but use it directly, without declaring
a separate variable on the stack.
Since I will need this net soon, I declare a struct net on the
stack and use it in the existing places in a separate patch not
to spoil the future ones.
Signed-off-by: Pavel Emelyanov <xemul@openvz.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This routine deals with ICMP statistics, but doesn't have a
struct net at hands, so add one.
Signed-off-by: Pavel Emelyanov <xemul@openvz.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch removes CVS keywords that weren't updated for a long time
from comments.
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add struct net_device parameter to ip_rt_frag_needed() and update MTU to
cache entries where ifindex is specified. This is similar to what is
already done in ip_rt_redirect().
Signed-off-by: Timo Teras <timo.teras@iki.fi>
Signed-off-by: David S. Miller <davem@davemloft.net>
What do_gettimeofday() does is to call getnstimeofday() and
to convert the result from timespec{} to timeval{}.
After that, these callers convert the result again to msec.
Use getnstimeofday() and convert the units at once.
Signed-off-by: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch makes the needlessly global icmp_sk_init() static.
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Replace sock_create_kern with inet_ctl_sock_create.
Signed-off-by: Denis V. Lunev <den@openvz.org>
Acked-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ICMP relookup path is only meant to modify behaviour when
appropriate IPsec policies are in place and marked as requiring
relookups. It is certainly not meant to modify behaviour when
IPsec policies don't exist at all.
However, due to an oversight on the error paths existing behaviour
may in fact change should one of the relookup steps fail.
This patch corrects this by redirecting all errors on relookup
failures to the previous code path. That is, if the initial
xfrm_lookup let the packet pass, we will stand by that decision
should the relookup fail due to an error.
This should be safe from a security point-of-view because compliant
systems must install a default deny policy so the packet would'nt
have passed in that case.
Many thanks to Julian Anastasov for pointing out this error.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 8b7817f3a9 ([IPSEC]: Add ICMP host
relookup support) introduced some dst leaks on error paths: the rt
pointer can be forgotten to be put. Fix it bu going to a proper label.
Found after net namespace's lo refused to unregister :) Many thanks to
Den for valuable help during debugging.
Herbert pointed out, that xfrm_lookup() will put the rtable in case
of error itself, so the first goto fix is redundant.
Signed-off-by: Pavel Emelyanov <xemul@openvz.org>
Signed-off-by: Denis V. Lunev <den@openvz.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This mostly re-uses the net, used in icmp netnsization patches from Denis.
After this ICMP sysctls are completely virtualized.
Signed-off-by: Pavel Emelyanov <xemul@openvz.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Initialization is moved to icmp_sk_init, all the places, that
refer to them use init_net for now.
Signed-off-by: Pavel Emelyanov <xemul@openvz.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Introduce per-net_device inlines: dev_net(), dev_net_set().
Without CONFIG_NET_NS, no namespace other than &init_net exists.
Let's explicitly define them to help compiler optimizations.
Signed-off-by: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
(Anonymous) unions can help us to avoid ugly casts.
A common cast it the (struct rtable *)skb->dst one.
Defining an union like :
union {
struct dst_entry *dst;
struct rtable *rtable;
};
permits to use skb->rtable in place.
Signed-off-by: Eric Dumazet <dada1@cosmosbay.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Functions from __exit section should not be called from ones in __init
section. Fix this conflict.
Signed-off-by: Denis V. Lunev <den@openvz.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
All preparations are done. Now just add a hook to perform an
initialization on namespace startup and replace icmp_sk macro with
proper inline call.
Signed-off-by: Denis V. Lunev <den@openvz.org>
Acked-by: Daniel Lezcano <dlezcano@fr.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
So, change icmp(v6)_sk creation/disposal to the scheme used in the
netlink for rtnl, i.e. create a socket in the context of the init_net
and assign the namespace without getting a referrence later.
Also use sk_release_kernel instead of sock_release to properly destroy
such sockets.
Signed-off-by: Denis V. Lunev <den@openvz.org>
Acked-by: Daniel Lezcano <dlezcano@fr.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Own __icmp(v6)_sk should be present in each namespace. So, it should be
allocated dynamically. Though, alloc_percpu does not fit the case as it
implies additional dereferrence for no bonus.
Allocate data for pointers just like __percpu_alloc_mask does and place
pointers to struct sock into this array.
Signed-off-by: Denis V. Lunev <den@openvz.org>
Acked-by: Daniel Lezcano <dlezcano@fr.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We have to get socket lock inside icmp(v6)_xmit_lock/unlock. The socket
is get from global variable now. When this code became namespaces, one
should pass a namespace and get socket from it.
Though, above is useless. Socket is available in the caller, just pass
it inside. This saves a bit of code now and saves more later.
add/remove: 0/0 grow/shrink: 1/3 up/down: 1/-169 (-168)
function old new delta
icmp_rcv 718 719 +1
icmpv6_rcv 2343 2303 -40
icmp_send 1566 1518 -48
icmp_reply 549 468 -81
Signed-off-by: Denis V. Lunev <den@openvz.org>
Acked-by: Daniel Lezcano <dlezcano@fr.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Basically, there is no difference, what to store: socket or sock. Though,
sock looks better as there will be 1 less dereferrence on the fast path.
Signed-off-by: Denis V. Lunev <den@openvz.org>
Acked-by: Daniel Lezcano <dlezcano@fr.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use this macro only once in a function to save a bit of space.
add/remove: 0/0 grow/shrink: 0/3 up/down: 0/-98 (-98)
function old new delta
icmp_reply 562 561 -1
icmp_push_reply 305 258 -47
icmp_init 273 223 -50
Signed-off-by: Denis V. Lunev <den@openvz.org>
Acked-by: Daniel Lezcano <dlezcano@fr.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
icmp_init could fail and this is normal for namespace other than initial.
So, the panic should be triggered only on init_net initialization path.
Additionally create rollback path for icmp_init as a separate function.
It will also be used later during namespace destruction.
Signed-off-by: Denis V. Lunev <den@openvz.org>
Acked-by: Daniel Lezcano <dlezcano@fr.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
struct net_proto_family* is not used in icmp[v6]_init, ndisc_init,
igmp_init and tcp_v4_init. Remove it.
Signed-off-by: Denis V. Lunev <den@openvz.org>
Acked-by: Daniel Lezcano <dlezcano@fr.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Somewhere along the development of my ICMP relookup patch the header
length check went AWOL on the non-IPsec path. This patch restores the
check.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
All needed API is done, the namespace is available when required from
the device on the DST entry from the incoming packet. So, just replace
init_net with proper namespace.
Other protocols will follow.
Signed-off-by: Denis V. Lunev <den@openvz.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Basically, this piece looks relatively easy. Namespace is already
available on the dst entry via device and the device is safe to
dereferrence. Compare it with one of a searcher and skip entry if
appropriate.
The only exception is ip_rt_frag_needed. So, add namespace parameter to it.
Signed-off-by: Denis V. Lunev <den@openvz.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Needed to propagate it down to the ip_route_output_flow.
Signed-off-by: Denis V. Lunev <den@openvz.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is only required to propagate it down to the
ip_route_output_slow.
Signed-off-by: Denis V. Lunev <den@openvz.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
On x86_64, sizeof(struct rtable) is 0x148, which is rounded up to
0x180 bytes by SLAB allocator.
We can reduce this to exactly 0x140 bytes, without alignment overhead,
and store 12 struct rtable per PAGE instead of 10.
rate_tokens is currently defined as an "unsigned long", while its
content should not exceed 6*HZ. It can safely be converted to an
unsigned int.
Moving tclassid right after rate_tokens to fill the 4 bytes hole
permits to save 8 bytes on 'struct dst_entry', which finally permits
to save 8 bytes on 'struct rtable'
Signed-off-by: Eric Dumazet <dada1@cosmosbay.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The patch extends the inet_addr_type and inet_dev_addr_type with the
network namespace pointer. That allows to access the different tables
relatively to the network namespace.
The modification of the signature function is reported in all the
callers of the inet_addr_type using the pointer to the well known
init_net.
Acked-by: Benjamin Thery <benjamin.thery@bull.net>
Acked-by: Daniel Lezcano <dlezcano@fr.ibm.com>
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
CHECK net/ipv4/icmp.c
net/ipv4/icmp.c:249:13: warning: context imbalance in 'icmp_xmit_unlock' -
unexpected unlock
net/ipv4/icmp.c:376:13: warning: context imbalance in 'icmp_reply' - different
lock contexts for basic block
net/ipv4/icmp.c:430:6: warning: context imbalance in 'icmp_send' - different
lock contexts for basic block
Solution is to declare both icmp_xmit_lock() and icmp_xmit_unlock() as inline
Signed-off-by: Eric Dumazet <dada1@cosmosbay.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller