Add the handler for HTT_T2H_MSG_TYPE_SEC_IND event from firmware, which stores
PN for replay check implemented in the following patch.
Tested on QCA6174 SDIO with firmware WLAN.RMH.4.4.1-00007-QCARMSWP-1.
Signed-off-by: Wen Gong <wgong@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Add the struct for PN replay protection and fragment packet
handler.
Also fix the bitmask of HTT_RX_DESC_HL_INFO_MCAST_BCAST to match what's currently
used by SDIO firmware. The defines are not used yet so it's safe to modify
them. Remove the conflicting HTT_RX_DESC_HL_INFO_FRAGMENT as
it's not either used in ath10k.
Tested on QCA6174 SDIO with firmware WLAN.RMH.4.4.1-00007-QCARMSWP-1.
Signed-off-by: Wen Gong <wgong@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Although not likely, the bundle allocation might fail.
Add proper error check and warning print.
Signed-off-by: Erik Stromdahl <erik.stromdahl@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
HTC header carries junk values that may be interpreted by the firmware
differently. Enable credit update only if flow control is enabled for
the corresponding endpoint.
Signed-off-by: Alagu Sankar <alagusankar@silex-india.com>
Signed-off-by: Erik Stromdahl <erik.stromdahl@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
With SDIO there's a use after free after a data frame is transfered, call stack
below. This happens because ath10k_htt_tx_hl() directly transmits the skb
provided by mac80211 using ath10k_htc_send(), all other HTT functions use
separate skb created with ath10k_htc_alloc_skb() to transmit the HTC packet.
After the packet is transmitted mac80211 frees the skb in ieee80211_tx_status()
but HTT layer expects that it still owns the skb, and frees it in
ath10k_htt_htc_tx_complete().
To fix this take a reference of skb before sending it to HTC layer to make sure
we still own the skb.
Tested on QCA6174 SDIO with firmware WLAN.RMH.4.4.1-00007-QCARMSWP-1.
ath10k_htt_tx_hl() is only used by SDIO and USB so other busses (PCI, AHB and
SNOC) should be unaffected.
call stack of use-after-free:
dump_backtrace+0x0/0x2d8
show_stack+0x20/0x2c
__dump_stack+0x20/0x28
dump_stack+0xc8/0xec
print_address_description+0x74/0x240
kasan_report+0x258/0x274
__asan_report_load4_noabort+0x20/0x28
skb_pull+0xbc/0x114
ath10k_htc_notify_tx_completion+0x190/0x2a4 [ath10k_core]
ath10k_sdio_write_async_work+0x1e4/0x2c4 [ath10k_sdio]
process_one_work+0x3d8/0x8b0
worker_thread+0x518/0x7e0
kthread+0x260/0x278
ret_from_fork+0x10/0x18
Allocated by one task:
kasan_kmalloc+0xa0/0x13c
kasan_slab_alloc+0x14/0x1c
kmem_cache_alloc+0x144/0x208
__alloc_skb+0xec/0x394
alloc_skb_with_frags+0x8c/0x374
sock_alloc_send_pskb+0x520/0x5d4
sock_alloc_send_skb+0x40/0x50
__ip_append_data+0xf5c/0x1858
ip_make_skb+0x194/0x1d4
udp_sendmsg+0xf24/0x1ab8
inet_sendmsg+0x1b0/0x2e0
sock_sendmsg+0x88/0xa0
__sys_sendto+0x220/0x3a8
__arm64_sys_sendto+0x78/0x80
el0_svc_common+0x120/0x1e0
el0_svc_compat_handler+0x64/0x80
el0_svc_compat+0x8/0x18
Freed by another task:
__kasan_slab_free+0x120/0x1d4
kasan_slab_free+0x10/0x1c
kmem_cache_free+0x74/0x504
kfree_skbmem+0x88/0xc8
__kfree_skb+0x24/0x2c
consume_skb+0x114/0x18c
__ieee80211_tx_status+0xb7c/0xf60 [mac80211]
ieee80211_tx_status+0x224/0x270 [mac80211]
ath10k_txrx_tx_unref+0x564/0x950 [ath10k_core]
ath10k_htt_t2h_msg_handler+0x178c/0x2a38 [ath10k_core]
ath10k_htt_htc_t2h_msg_handler+0x20/0x30 [ath10k_core]
ath10k_sdio_irq_handler+0xcc0/0x1654 [ath10k_sdio]
process_sdio_pending_irqs+0xec/0x358
sdio_run_irqs+0x68/0xe4
sdio_irq_work+0x1c/0x28
process_one_work+0x3d8/0x8b0
worker_thread+0x518/0x7e0
kthread+0x260/0x278
ret_from_fork+0x10/0x18
Reported-by: Wen Gong <wgong@codeaurora.org>
Tested-by: Wen Gong <wgong@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Transmit completion for SDIO is similar to PCIe, modify the high
latency path to allow SDIO modules to use the msdu id.
kvalo: the original patch from Alagu enabled this only for SDIO but I'm not
sure should we also enable this with USB. I'll use bus params to enable this
for so that it's easy to enable also for USB later.
Tested with QCA6174 SDIO with firmware WLAN.RMH.4.4.1-00007-QCARMSWP-1.
Co-developed-by: Wen Gong <wgong@codeaurora.org>
Signed-off-by: Alagu Sankar <alagusankar@silex-india.com>
Signed-off-by: Wen Gong <wgong@codeaurora.org>.
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This way we don't need to set every variable and give them to default, which is
zero. This is also safer in case we forgot to initalise a new field in some of
the bus modules.
Compile tested only.
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
HTT High Latency (ATH10K_DEV_TYPE_HL) does not use txdone_fifo at all, we don't
even initialise it by skipping ath10k_htt_tx_alloc_buf() in
ath10k_htt_tx_start(). Because of this using QCA6174 SDIO
ath10k_htt_rx_tx_compl_ind() will crash when it accesses unitialised
txdone_fifo. So skip txdone_fifo when using High Latency mode.
Tested with QCA6174 SDIO with firmware WLAN.RMH.4.4.1-00007-QCARMSWP-1.
Co-developed-by: Wen Gong <wgong@codeaurora.org>
Signed-off-by: Alagu Sankar <alagusankar@silex-india.com>
Signed-off-by: Wen Gong <wgong@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Disabling interrupts this early meant WMI communication was not working anymore
when the SDIO device was removed. But we call ath10k_core_unregister() that
will eventually call ath10k_sdio_hif_stop(), which disables the interrupts. So
there's actually no need to disable interrupts here.
Also remove cancel_work_sync() as it's also called in ath10k_sdio_hif_stop().
Tested with QCA6174 SDIO with firmware WLAN.RMH.4.4.1-00007-QCARMSWP-1.
Signed-off-by: Wen Gong <wgong@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
On QCA6174 SDIO devices the SDIO interrupt will fail if UART is
disabled from ath10k. SDIO firmware enables UART printouts by
default. If ath10k will try to enable UART again the firmware
will configure it's GPIO line incorrectly and SDIO interrupts
won't work anymore. The workaround is to set UART pin again (19
for QCA6174 SDIO) if uart_print is 0.
Tested with QCA6174 SDIO with firmware WLAN.RMH.4.4.1-00007-QCARMSWP-1.
Signed-off-by: Wen Gong <wgong@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
David Bauer says:
====================
net: add reset-controller driven PHY reset
This patchset adds support for a PHY reset driven by a reset-controller.
Currently, only GPIO driven resets are supported by the PHY subsystem.
It also renames the reset-gpio from 'reset' to 'reset_gpio' to
better differentiate between resets wired to a GPIO and resets wired to
a reset-controller driven pin.
Some systems have the PHY reset-line wired to a pin controlled by a
reset-controller (eg. some Atheros AR9132 based boards). In case the
bootloader asserts reset before loading the kernel, we currently do not
have a clean way of deasserting reset to probe the PHY.
v3:
- add missing newline in mdio_bus.c
v2:
- fixed missed rename of "reset" in at803x.c
- move initial reset to mdio_device_reset
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
This renames the GPIO reset of mdio devices from 'reset' to
'reset_gpio' to better differentiate between GPIO and
reset-controller driven reset line.
Signed-off-by: David Bauer <mail@david-bauer.net>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
This commit adds support for PHY reset pins handled by a reset controller.
Signed-off-by: David Bauer <mail@david-bauer.net>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add the documentation for PHY reset lines controlled by a reset controller.
Signed-off-by: David Bauer <mail@david-bauer.net>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jakub Kicinski says:
====================
net: some build fixes and other improvements
A few unrelated improvements here, mostly trying to make random
configs build and W=1 produce a little less warnings under net/
and drivers net/.
First two patches fix set but not used warnings with W=1.
Next patch fixes 64bit division in sch_taprio.c.
Last two patches are getting rid of some (almost) unused asserts
in skbuff.h.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
We are discouraging the use of BUG() these days, remove the
unused ASSERT macros from skbuff.h.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Dirk van der Merwe <dirk.vandermerwe@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The driver does not advertize NETIF_F_FRAGLIST, the stack can't
pass skbs with frags lists to the xmit function.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Dirk van der Merwe <dirk.vandermerwe@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Recent changes to taprio did not use the correct div64 helpers,
leading to:
net/sched/sch_taprio.o: In function `taprio_dequeue':
sch_taprio.c:(.text+0x34a): undefined reference to `__divdi3'
net/sched/sch_taprio.o: In function `advance_sched':
sch_taprio.c:(.text+0xa0b): undefined reference to `__divdi3'
net/sched/sch_taprio.o: In function `taprio_init':
sch_taprio.c:(.text+0x1450): undefined reference to `__divdi3'
/home/jkicinski/devel/linux/Makefile:1032: recipe for target 'vmlinux' failed
Use math64 helpers.
Fixes: 7b9eba7ba0 ("net/sched: taprio: fix picos_per_byte miscalculation")
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Dirk van der Merwe <dirk.vandermerwe@netronome.com>
Acked-by: Vinicius Costa Gomes <vinicius.gomes@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
GCC 8 complains:
drivers/net/sb1000.c: In function ‘card_send_command’:
drivers/net/sb1000.c:319:14: warning: variable ‘x’ set but not used [-Wunused-but-set-variable]
int status, x;
^
drivers/net/sb1000.c: In function ‘sb1000_check_CRC’:
drivers/net/sb1000.c:493:6: warning: variable ‘crc’ set but not used [-Wunused-but-set-variable]
int crc, status;
^~~
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Dirk van der Merwe <dirk.vandermerwe@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
GCC complains:
net/l2tp/l2tp_ppp.c: In function ‘pppol2tp_ioctl’:
net/l2tp/l2tp_ppp.c:1073:6: warning: variable ‘val’ set but not used [-Wunused-but-set-variable]
int val;
^~~
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Dirk van der Merwe <dirk.vandermerwe@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
To make ICMPv6 closer to ICMPv4, add ratemask parameter. Since the ICMP
message types use larger numeric values, a simple bitmask doesn't fit.
I use large bitmap. The input and output are the in form of list of
ranges. Set the default to rate limit all error messages but Packet Too
Big. For Packet Too Big, use ratemask instead of hard-coded.
There are functions where icmpv6_xrlim_allow() and icmpv6_global_allow()
aren't called. This patch only adds them to icmpv6_echo_reply().
Rate limiting error messages is mandated by RFC 4443 but RFC 4890 says
that it is also acceptable to rate limit informational messages. Thus,
I removed the current hard-coded behavior of icmpv6_mask_allow() that
doesn't rate limit informational messages.
v2: Add dummy function proc_do_large_bitmap() if CONFIG_PROC_SYSCTL
isn't defined, expand the description in ip-sysctl.txt and remove
unnecessary conditional before kfree().
v3: Inline the bitmap instead of dynamically allocated. Still is a
pointer to it is needed because of the way proc_do_large_bitmap work.
Signed-off-by: Stephen Suryaputra <ssuryaextr@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
phy_sanitize_settings() is called from phy_start_aneg() only, and only
if phydev->autoneg isn't set. Therefore the removed code does nothing.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In phy_device_create() we set phydev->autoneg = 1. This isn't changed
even if the PHY doesn't support autoneg. This seems to affect very
few PHY's, and they disable phydev->autoneg in their config_init
callback. So it's more of an improvement, therefore net-next.
The patch also wouldn't apply to older kernel versions because the
link mode bitmaps have been introduced recently.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jeff Kirsher says:
====================
100GbE Intel Wired LAN Driver Updates 2019-04-18
This series contains updates to the ice driver only.
Anirudh fixes up code comments which had typos. Added support for DCB
into the ice driver, which required a bit of refactoring of the existing
code. Also fixed a potential race condition between closing and opening
the VSI for a MIB change event, so resolved this by grabbing the
rtnl_lock prior to closing. Added support to process LLDP MIB change
notifications. Added support for reporting DCB stats via ethtool.
Brett updates the calculation to increment ITR to use a direct
calculation instead of using estimations. This provides a more accurate
value.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Nothing really special standing out this time, iwlwifi being the most
active driver.
Major changes:
iwlwifi
* send NO_DATA events so they can be captured in radiotap
* support for multiple BSSID
* support for some new FW API versions
* support new hardware
* debugfs cleanups by Greg-KH
qtnfmac
* allow each MAC to specify its own regulatory rules
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJcuHgsAAoJEG4XJFUm622bfo8H/3uRRxsQBHGg6e3NpELaxpNV
IfrPDtvxyfILzIepBBhnZYUY0OrlTHKfMmzFBD9FFMojsxBYddnLZ/0iKUNKfwLm
KzToW/64YJ784dc+tw85gjh8I3MB+RRoD0l01M1HuOkzQ4hDNEGK3IsMHsBs/oTZ
huiqTYsTxStOj53vOpQiBFZ1pYBtvGLMxBdSepDcR27bgT1gwriynCSkSNglDH8z
/t3m6hDGtZa6uVkoIVH+BAMu6+vt+vIkU/TOdmiW/zqBL2JYq6cDE0uIb3bLAzN6
uvS1Rj42P3OwHUwFavlUBdr5Rdcj6P24S5ZhtVaGGWCBjMZI5/nO7IjzwyQnQuQ=
=/6q9
-----END PGP SIGNATURE-----
Merge tag 'wireless-drivers-next-for-davem-2019-04-18' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers-next
Kalle Valo says:
====================
wireless-drivers-next patches for 5.2
Nothing really special standing out this time, iwlwifi being the most
active driver.
Major changes:
iwlwifi
* send NO_DATA events so they can be captured in radiotap
* support for multiple BSSID
* support for some new FW API versions
* support new hardware
* debugfs cleanups by Greg-KH
qtnfmac
* allow each MAC to specify its own regulatory rules
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently when calculating how much to increment ITR by inside of
ice_update_itr() we do some estimations and intermediate
calculations. Instead of doing estimations, just do the
calculation directly. This allows for a more accurate value and it
makes it easier for the next person to understand and update.
Also, remove the dividing the ITR value by 2 when latency
driven because the ITR values are already so low for 100Gbps
speed. This should help get to the desired ITR value faster.
Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Update driver version to 0.7.4
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch adds code to start or stop LLDP and DCBX in firmware through
use of ethtool private flags.
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch introduces a new function ice_dcb_rebuild which reinitializes
DCB after a reset.
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch adds a new function ice_update_dcb_stats to get DCB stats
from the hardware and ethtool support for displaying these stats.
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch introduces a new function ice_tx_prepare_vlan_flags_dcb to
insert 802.1p priority information into the VLAN header
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch adds a new function ice_vsi_cfg_dcb_rings which updates a
VSI's rings based on DCB traffic class information.
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch adds support to process LLDP MIB change notifications sent
by the firmware.
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
When the firmware doesn't support LLDP or DCBX, the driver should switch
to "software LLDP mode". This patch adds support for the same.
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch adds a new function ice_pf_dcb_cfg (and related helpers)
which applies the DCB configuration obtained from the firmware. As
part of this, VSIs/netdevs are updated with traffic class information.
This patch requires a bit of a refactor of existing code.
1. For a MIB change event, the associated VSI is closed and brought up
again. The gap between closing and opening the VSI can cause a race
condition. Fix this by grabbing the rtnl_lock prior to closing the
VSI and then only free it after re-opening the VSI during a MIB
change event.
2. ice_sched_query_elem is used in ice_sched.c and with this patch, in
ice_dcb.c as well. However, ice_dcb.c is not built when CONFIG_DCB is
unset. This results in namespace warnings (ice_sched.o: Externally
defined symbols with no external references) when CONFIG_DCB is unset.
To avoid this move ice_sched_query_elem from ice_sched.c to
ice_common.c.
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch introduces a new top level function ice_init_dcb (and
related lower level helper functions) which continues the DCB init
flow.
This function uses ice_get_dcb_cfg to get, parse and store the DCB
configuration. Once this is done, it sets itself up to be notified
by the firmware on LLDP MIB change events.
Reviewed-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch introduces a skeleton for ice_init_pf_dcb, the top level
function for DCB initialization. Subsequent patches will add to this
DCB init flow.
In this patch, ice_init_pf_dcb checks if DCB is a supported capability.
If so, an admin queue call to start the LLDP and DCBx in firmware is
issued. If not, an error is reported. Note that we don't fail the driver
init if DCB init fails.
Reviewed-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Bump driver version to 0.7.3
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Capitalize abbreviations and spell out some that aren't obvious.
Reviewed-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch fixes typos in code comments.
Reviewed-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Somehow file drivers/net/wireless/realtek/rtlwifi/rtl8188ee/trx.c.rej was
incorporated into the sources. Obviously, it can be removed.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Reported-by: Andrew Morton <akpm@linux-foundation.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Disabling IPv6 on an interface removes existing entries but nothing prevents
new entries from being manually added. To that end, add a new neigh_table
operation, allow_add, that is called on RTM_NEWNEIGH to see if neighbor
entries are allowed on a given device. If IPv6 is disabled on the device,
allow_add returns false and passes a message back to the user via extack.
$ echo 1 > /proc/sys/net/ipv6/conf/eth1/disable_ipv6
$ ip -6 neigh add fe80::4c88:bff:fe21:2704 dev eth1 lladdr de:ad:be:ef:01:01
Error: IPv6 is disabled on this device.
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David Ahern says:
====================
ipv6: Use fib6_result for fib_lookups
Add fib6_result as a single data structure to hold results from a fib
lookup. IPv6 currently has everything in 1 data structure - a fib6_info,
but with nexthop objects the fib6_nh can be in a nexthop or a nexthop
can be a blackhole which affects the fib6_type and flags (REJECT).
v2
- fixed 2 bugs in patch12:
i. checking return from fib6_table_lookup in fib6_lookup
ii. call to fib6_rule_saddr in fib6_rule_action_alt should use res->nh
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Add the fib6_flags and fib6_type to fib6_result. Update the lookup helpers
to set them and update post fib lookup users to use the version from the
result.
This allows nexthop objects to have blackhole nexthop.
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Change fib6_lookup and fib6_table_lookup to take a fib6_result and set
f6i and nh rather than returning a fib6_info. For now both always
return 0.
A later patch set can make these more like the IPv4 counterparts and
return EINVAL, EACCESS, etc based on fib6_type.
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Change fib6_table_lookup tracepoint to take the fib6_result and use
the fib6_info and fib6_nh from it.
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pass fib6_result to rt6_select. Instead of returning the fib entry, it
will set f6i and nh based on the lookup.
find_rr_leaf is changed to remove the match option in favor of taking
fib6_result and having __find_rr_leaf set f6i in the result.
In the process, update fib6_info references in __find_rr_leaf to f6i names.
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pass fib6_result to rt6_device_match with f6i set. rt6_device_match
updates f6i in the result if it finds a better match and sets nh.
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Change ip6_mtu_from_fib6 and fib6_mtu to take a fib6_result over a
fib6_info. Update both to use the fib6_nh from fib6_result.
Since the signature of ip6_mtu_from_fib6 is already changing, add const
to daddr and saddr.
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Wen Gong