Thermal is TS-ADC Controller module supports
user-defined mode and automatic mode.
User-defined mode refers,TSADC all the control signals entirely by
software writing to register for direct control.
Automaic mode refers to the module automatically poll TSADC output,
and the results were checked.If you find that the temperature High
in a period of time,an interrupt is generated to the processor
down-measures taken;If the temperature over a period of time High,
the resulting TSHUT gave CRU module,let it reset the entire chip,
or via GPIO give PMIC.
Signed-off-by: zhaoyifeng <zyf@rock-chips.com>
Signed-off-by: Caesar Wang <caesar.wang@rock-chips.com>
Reviewed-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
This adds support for the Tegra SOCTHERM thermal sensing and management
system found in the Tegra124 system-on-chip. This initial driver supports
temperature polling for four thermal zones.
Signed-off-by: Mikko Perttunen <mperttunen@nvidia.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
This patch introduces a new thermal cooling device based on common clock
framework. The original motivation to write this cooling device is to be
able to cool down thermal zones using clocks that feed co-processors, such
as GPUs, DSPs, Image Processing Co-processors, etc. But it is written
in a way that it can be used on top of any clock.
The implementation is pretty straight forward. The code creates
a thermal cooling device based on a pair of a struct device and a clock name.
The struct device is assumed to be usable by the OPP layer. The OPP layer
is used as source of the list of possible frequencies. The (cpufreq) frequency
table is then used as a map from frequencies to cooling states. Cooling
states are indexes to the frequency table.
The logic sits on top of common clock framework, specifically on clock
pre notifications. Any PRE_RATE_CHANGE is hijacked, and the transition is
only allowed when the new rate is within the thermal limit (cooling state -> freq).
When a thermal cooling device state transition is requested, the clock
is also checked to verify if the current clock rate is within the new
thermal limit.
Cc: Zhang Rui <rui.zhang@intel.com>
Cc: Mike Turquette <mturquette@linaro.org>
Cc: Nishanth Menon <nm@ti.com>
Cc: Pavel Machek <pavel@ucw.cz>
Cc: "Rafael J. Wysocki" <rjw@sisk.pl>
Cc: Len Brown <len.brown@intel.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: linux-pm@vger.kernel.org
Cc: linux-arm-kernel@lists.infradead.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Eduardo Valentin <eduardo.valentin@ti.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
Pull thermal management updates from Zhang Rui:
"Sorry that I missed the merge window as there is a bug found in the
last minute, and I have to fix it and wait for the code to be tested
in linux-next tree for a few days. Now the buggy patch has been
dropped entirely from my next branch. Thus I hope those changes can
still be merged in 3.18-rc2 as most of them are platform thermal
driver changes.
Specifics:
- introduce ACPI INT340X thermal drivers.
Newer laptops and tablets may have thermal sensors and other
devices with thermal control capabilities that are exposed for the
OS to use via the ACPI INT340x device objects. Several drivers are
introduced to expose the temperature information and cooling
ability from these objects to user-space via the normal thermal
framework.
From: Lu Aaron, Lan Tianyu, Jacob Pan and Zhang Rui.
- introduce a new thermal governor, which just uses a hysteresis to
switch abruptly on/off a cooling device. This governor can be used
to control certain fan devices that can not be throttled but just
switched on or off. From: Peter Feuerer.
- introduce support for some new thermal interrupt functions on
i.MX6SX, in IMX thermal driver. From: Anson, Huang.
- introduce tracing support on thermal framework. From: Punit
Agrawal.
- small fixes in OF thermal and thermal step_wise governor"
* 'next' of git://git.kernel.org/pub/scm/linux/kernel/git/rzhang/linux: (25 commits)
Thermal: int340x thermal: select ACPI fan driver
Thermal: int3400_thermal: use acpi_thermal_rel parsing APIs
Thermal: int340x_thermal: expose acpi thermal relationship tables
Thermal: introduce int3403 thermal driver
Thermal: introduce INT3402 thermal driver
Thermal: move the KELVIN_TO_MILLICELSIUS macro to thermal.h
ACPI / Fan: support INT3404 thermal device
ACPI / Fan: add ACPI 4.0 style fan support
ACPI / fan: convert to platform driver
ACPI / fan: use acpi_device_xxx_power instead of acpi_bus equivelant
ACPI / fan: remove no need check for device pointer
ACPI / fan: remove unused macro
Thermal: int3400 thermal: register to thermal framework
Thermal: int3400 thermal: add capability to detect supporting UUIDs
Thermal: introduce int3400 thermal driver
ACPI: add ACPI_TYPE_LOCAL_REFERENCE support to acpi_extract_package()
ACPI: make acpi_create_platform_device() an external API
thermal: step_wise: fix: Prevent from binary overflow when trend is dropping
ACPI: introduce ACPI int340x thermal scan handler
thermal: Added Bang-bang thermal governor
...
we share the same driver for both ACPI predefined Fan device
and INT3404 Fan device, thus we should select the ACPI Fan
driver when int340x thermal drivers are enabeld.
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
ACPI 4.0 introduced two thermal relationship tables via _ART
(active cooling) and _TRT (passive cooling) objects. These
tables contain many to many relationships among thermal sensors
and cooling devices.
This patch parses _ART and _TRT and makes the result available to
the userspace via an misc device interface. At the same time,
kernel drivers can also request parsing results from internal
kernel APIs.
The results include source and target devices, influence, and
sampling rate in case of _TRT. For _ART, the result shows source
device, target device, and weight percentage.
Signed-off-by: Jacob Pan <jacob.jun.pan@linux.intel.com>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
ACPI INT3403 device object can be used to retrieve temperature date
from temperature sensors present in the system, and to expose
device' performance control.
The previous INT3403 thermal driver supports temperature reporting only,
thus remove it and introduce this new & enhanced one.
Signed-off-by: Lan Tianyu <tianyu.lan@intel.com>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Introduce int3400 thermal driver. And make INT3400 driver
enumerate the other int340x thermal components shown in _ART/_TRT.
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Newer laptops and tablets that use ACPI may have thermal sensors and
other devices with thermal control capabilities outside the core CPU/SOC,
for thermal safety reasons.
They are exposed for the OS to use via
1) INT3400 ACPI device object as the master.
2) INT3401 ~ INT340B ACPI device objects as the slaves.
This patch introduces a scan handler to enumerate the INT3400
ACPI device object to platform bus, and prevent its slaves
from being enumerated before the controller driver being probed.
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
mach-kirkwood has been removed, now that kirkwood lives in mach-mvebu.
Depend on MACH_KIRKWOOD, which will be set when kirkwood is built as
part of ARCH_MVEBU.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Cc: Zhang Rui <rui.zhang@intel.com>
Cc: linux-pm@vger.kernel.org
Acked-by: Eduardo Valentin <edubezval@gmail.com>
Link: https://lkml.kernel.org/r/1409417172-6846-4-git-send-email-andrew@lunn.ch
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
The bang-bang thermal governor uses a hysteresis to switch abruptly on
or off a cooling device. It is intended to control fans, which can
not be throttled but just switched on or off.
Bang-bang cannot be set as default governor as it is intended for
special devices only. For those special devices the driver needs to
explicitely request it.
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Zhang Rui <rui.zhang@intel.com>
Cc: Andreas Mohr <andi@lisas.de>
Cc: Borislav Petkov <bp@suse.de>
Cc: Javi Merino <javi.merino@arm.com>
Cc: linux-pm@vger.kernel.org
Signed-off-by: Peter Feuerer <peter@piie.net>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
DT-enabled Dove has moved from ARCH_DOVE in mach-dove to MACH_DOVE
in mach-mvebu. As non-DT ARCH_DOVE will stay to rot for a while, add a new
DT-only MACH_DOVE to thermal Kconfig.
This was originally supposed to go in via "ARM: dove: prepare new Dove DT Kconfig"
patch from Sebastian Hesselbarth for 3.15, but slipped through the cracks.
I've tested on CuBox that without this patch you can't compile
dove_thermal into a mach-mvebu based kernel, and with this patch I can
build the driver and it works as expected run-time.
v2: non-ascii char creeped in somehow
Signed-off-by: Riku Voipio <riku.voipio@linaro.org>
Cc: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Cc: Zhang Rui <rui.zhang@intel.com>
Cc: Eduardo Valentin <edubezval@gmail.com>
Cc: linux-pm@vger.kernel.org
Cc: linux-arm-kernel@lists.infradead.org
Acked-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
This core is shared by both ST's 'memory mapped' and
'system configuration register' based Thermal controllers.
Signed-off-by: Ajit Pal Singh <ajitpal.singh@st.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
In the Intel SoCs like Bay Trail, there are 2 additional digital temperature
sensors(DTS), in addition to the standard DTSs in the core. Also they support
4 programmable thresholds, out of which two can be used by OSPM. These
thresholds can be used by OSPM thermal control. Out of these two thresholds,
one is used by driver and one user mode can change via thermal sysfs to get
notifications on threshold violations.
The driver defines one critical trip points, which is set to TJ MAX - offset.
The offset can be changed via module parameter (default 5C). Also it uses
one of the thresholds to get notification for this temperature violation.
This is very important for orderly shutdown as the many of these devices don't
have ACPI thermal zone, and expects that there is some other thermal control
mechanism present in OSPM. When a Linux distro is used without additional
specialized thermal control program, BIOS can do force shutdown when thermals
are not under control. When temperature reaches critical, the Linux thermal
core will initiate an orderly shutdown.
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Menu for Samsung thermal support is visible on all Samsung
platforms while thermal drivers are currently available only
for EXYNOS SoCs. Fix it by replacing PLAT_SAMSUNG dependency
with ARCH_EXYNOS one.
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Acked-by: Amit Daniel Kachhap <amit.daniel@samsung.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
These changes are mostly for ARM specific device drivers that either
don't have an upstream maintainer, or that had the maintainer ask
us to pick up the changes to avoid conflicts. A large chunk of this
are clock drivers (bcm281xx, exynos, versatile, shmobile), aside from
that, reset controllers for STi as well as a large rework of the
Marvell Orion/EBU watchdog driver are notable.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=u/FI
-----END PGP SIGNATURE-----
Merge tag 'drivers-3.15' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC driver changes from Arnd Bergmann:
"These changes are mostly for ARM specific device drivers that either
don't have an upstream maintainer, or that had the maintainer ask us
to pick up the changes to avoid conflicts.
A large chunk of this are clock drivers (bcm281xx, exynos, versatile,
shmobile), aside from that, reset controllers for STi as well as a
large rework of the Marvell Orion/EBU watchdog driver are notable"
* tag 'drivers-3.15' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (99 commits)
Revert "dts: socfpga: Add DTS entry for adding the stmmac glue layer for stmmac."
Revert "net: stmmac: Add SOCFPGA glue driver"
ARM: shmobile: r8a7791: Fix SCIFA3-5 clocks
ARM: STi: Add reset controller support to mach-sti Kconfig
drivers: reset: stih416: add softreset controller
drivers: reset: stih415: add softreset controller
drivers: reset: Reset controller driver for STiH416
drivers: reset: Reset controller driver for STiH415
drivers: reset: STi SoC system configuration reset controller support
dts: socfpga: Add sysmgr node so the gmac can use to reference
dts: socfpga: Add support for SD/MMC on the SOCFPGA platform
reset: Add optional resets and stubs
ARM: shmobile: r7s72100: fix bus clock calculation
Power: Reset: Generalize qnap-poweroff to work on Synology devices.
dts: socfpga: Update clock entry to support multiple parents
ARM: socfpga: Update socfpga_defconfig
dts: socfpga: Add DTS entry for adding the stmmac glue layer for stmmac.
net: stmmac: Add SOCFPGA glue driver
watchdog: orion_wdt: Use %pa to print 'phys_addr_t'
drivers: cci: Export CCI PMU revision
...
Commit beeb5a1e (thermal: rcar-thermal: Enable driver compilation with COMPILE_TEST)
broke build on archs wihout io memory.
On archs like S390 or um this driver cannot build nor work.
Make it depend on HAS_IOMEM to bypass build failures.
drivers/thermal/rcar_thermal.c:404: undefined reference to `devm_ioremap_resource'
drivers/thermal/rcar_thermal.c:426: undefined reference to `devm_ioremap_resource'
Signed-off-by: Richard Weinberger <richard@nod.at>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
With the move of kirkwood into mach-mvebu, drivers Kconfig need
tweeking to allow the kirkwood specific drivers to be built.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Mark Brown <broonie@linaro.org>
Acked-by: Kishon Vijay Abraham I <kishon@ti.com>
Acked-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Tested-by: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
Cc: Viresh Kumar <viresh.kumar@linaro.org>
Cc: Rafael J. Wysocki <rjw@rjwysocki.net>
Cc: Richard Purdie <rpurdie@rpsys.net>
Cc: Bryan Wu <cooloney@gmail.com>
Cc: Zhang Rui <rui.zhang@intel.com>
Cc: Eduardo Valentin <eduardo.valentin@ti.com>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
The ACPI INT3403 device objects present on some systems can be used to retrieve
temperature data from thermal sensors. Add a driver registering each INT3403
device object as a thermal zone device and exposing its _TMP, PATx and GTSH
method via the standard thermal control interface under /sys/class/thermal/.
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
This patch introduces an API to register cpufreq cooling device
based on device tree node.
The registration via device tree node differs from normal
registration due to the fact that it is needed to fill
the device_node structure in order to be able to match
the cooling devices with trip points.
Cc: Zhang Rui <rui.zhang@intel.com>
Cc: linux-pm@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Eduardo Valentin <eduardo.valentin@ti.com>
This patch introduces a device tree bindings for
describing the hardware thermal behavior and limits.
Also a parser to read and interpret the data and feed
it in the thermal framework is presented.
This patch introduces a thermal data parser for device
tree. The parsed data is used to build thermal zones
and thermal binding parameters. The output data
can then be used to deploy thermal policies.
This patch adds also documentation regarding this
API and how to define tree nodes to use
this infrastructure.
Note that, in order to be able to have control
on the sensor registration on the DT thermal zone,
it was required to allow changing the thermal zone
.get_temp callback. For this reason, this patch
also removes the 'const' modifier from the .ops
field of thermal zone devices.
Cc: Zhang Rui <rui.zhang@intel.com>
Cc: linux-pm@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Acked-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Eduardo Valentin <eduardo.valentin@ti.com>
Pull thermal management updates from Zhang Rui:
"This time we only have a few changes as there are no soc thermal
changes from Eduardo. The only big change is the introduction of
TMON, a tool to help visualize, tune, and test the thermal subsystem.
The rest is mostly cleanups and fixes all over.
Specifics:
- introduce TMON, a tool base on thermal sysfs I/F. It can be used
to visualize, tune and test the thermal subsystem.
- fix a zone/cooling device binding problem, when both thermal zone
bind parameters and .bind() callback are available"
* 'next' of git://git.kernel.org/pub/scm/linux/kernel/git/rzhang/linux:
tools/thermal: Introduce tmon, a tool for thermal subsystem
thermal: Fix binding problem when there is thermal zone params
thermal: cpu_cooling: fix return value check in cpufreq_cooling_register()
Thermal: Check for validity before doing kfree
thermal/intel_powerclamp: Add newer CPU models
Thermal: Tidy up error handling in powerclamp_init
thermal: Kconfig: cosmetic fixes
ACPI/thermal : Remove zone disabled warning
typo in drivers/thermal/Kconfig: lpatform instead of platform
CONFIG_CPU_FREQ_TABLE will be always enabled when cpufreq framework is used, as
cpufreq core depends on it. So, we don't need this CONFIG option anymore as it
is not configurable. Remove CONFIG_CPU_FREQ_TABLE and update its users.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
In order to improve code organization, this patch
moves the hwmon sysfs support to a file named
thermal_hwmon. This helps to add extra support
for hwmon without scrambling the code.
In order to do this move, the hwmon list head is now
using its own locking. Before, the list used
the global thermal locking. Also, some minor changes
in the code were required, as recommended by checkpatch.pl.
Cc: Zhang Rui <rui.zhang@intel.com>
Cc: linux-pm@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Acked-by: Durgadoss R <durgadoss.r@intel.com>
Signed-off-by: Eduardo Valentin <eduardo.valentin@ti.com>
This movement of files is done for easy maintenance and adding more
new sensor's support for exynos platform easily . This will also help in
bifurcating exynos common, sensor driver and sensor data related parts.
Acked-by: Kukjin Kim <kgene.kim@samsung.com>
Acked-by: Jonghwa Lee <jonghwa3.lee@samsung.com>
Acked-by: Eduardo Valentin <eduardo.valentin@ti.com>
Signed-off-by: Amit Daniel Kachhap <amit.daniel@samsung.com>
Signed-off-by: Eduardo Valentin <eduardo.valentin@ti.com>
This is based on the initial imx thermal work done by
Rob Lee <rob.lee@linaro.org> (Not sure if the email address is still
valid). Since he is no longer interested in the work and I have
rewritten a significant amount of the code, I just took the authorship
over from him.
It adds the imx thermal support using Temperature Monitor (TEMPMON)
block found on some Freescale i.MX SoCs. The driver uses syscon regmap
interface to access TEMPMON control registers and calibration data, and
supports cpufreq as the cooling device.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Eduardo Valentin <eduardo.valentin@ti.com>
Fix build error in x86_pkg_temp_thermal.c. It requires that
X86_MCE & X86_THERMAL_VECTOR be enabled, so depend on the latter symbol,
since it depends on X86_MCE (indirectly).
Also, X86_PKG_TEMP_THERMAL is already inside an "if THERMAL" block,
so remove that duplicated dependency.
ERROR: "platform_thermal_package_rate_control" [drivers/thermal/x86_pkg_temp_thermal.ko] undefined!
ERROR: "platform_thermal_package_notify" [drivers/thermal/x86_pkg_temp_thermal.ko] undefined!
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Acked-by: Borislav Petkov <bp@suse.de>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
This driver register CPU digital temperature sensor as a thermal
zone at package level.
Each package will show up as one zone with at max two trip points.
These trip points can be both read and updated. Once a non zero
value is set in the trip point, if the package package temperature
goes above or below this setting, a thermal notification is
generated.
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
There is no support for hotplug or any other means of reducing
temperature. So, this patch removes these references from Kconfig.
Signed-off-by: Eduardo Valentin <eduardo.valentin@ti.com>
Acked-by: Amit Daniel Kachhap <amit.daniel@samsung.com>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Because this feature is for debuging purposes, it is highly
recommended to do not enable this on production systems.
This patch adds warnings for system integrators, so that
people are aware of this potential security issue.
Signed-off-by: Eduardo Valentin <eduardo.valentin@ti.com>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
This removes the driver specific sysfs support of the temperature
emulation and uses the newly added core thermal framework for thermal
emulation. An exynos platform specific handler is added to support this.
In this patch, the exynos senor(tmu) related code and exynos framework
related (thermal zone, cooling devices) code are intentionally kept separate.
So an emulated function pointer is passed from sensor to framework. This is
beneficial in adding more sensor support using the same framework code
which is an ongoing work. The goal is to finally split them totally. Even
the existing read_temperature also follows the same execution method.
Acked-by: Kukjin Kim <kgene.kim@samsung.com>
Signed-off-by: Amit Daniel Kachhap <amit.daniel@samsung.com>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
This driver supports both Armada 370 and Armada XP SoC
thermal management controllers.
Armada 370 has a register to check a valid temperature, whereas
Armada XP does not. Each has a different initialization (i.e. calibration)
function. The temperature conversion formula is the same for both.
The controller present in each SoC have a very similar feature set,
so it corresponds to have one driver to support both of them.
Although this driver may present similarities to Dove and Kirkwood
thermal driver, the exact differences and coincidences are not fully
known. For this reason, support is given through a separate driver.
Signed-off-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Currently, we have three Kconfig options for thermal governors, aka,
CONFIG_FAIR_SHARE, CONFIG_USER_SPACE and CONFIG_STEP_WISE.
But these names are too generic that may bring confusion to users.
Rename them to CONFIG_THERMAL_GOV_FAIR_SHARE,
CONFIG_THERMAL_GOV_USER_SPACE, CONFIG_THERMAL_GOV_STEP_WISE
to avoid the generic naming.
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
The Marvell Dove SoC has a thermal sensor. Add a driver using the
thermal framework.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
This patch adds support for Kirkwood 88F6282 and 88F6283 thermal sensor.
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
This patch adds support to set the emulated temperature method in
thermal zone (sensor). After setting this feature thermal zone may
report this temperature and not the actual temperature. The emulation
implementation may be based on sensor capability through platform
specific handler or pure software emulation if no platform handler defined.
This is useful in debugging different temperature threshold and its
associated cooling action. Critical threshold's cannot be emulated.
Writing 0 on this node should disable emulation.
Signed-off-by: Amit Daniel Kachhap <amit.daniel@samsung.com>
Acked-by: Kukjin Kim <kgene.kim@samsung.com>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Intel PowerClamp driver performs synchronized idle injection across
all online CPUs. The goal is to maintain a given package level C-state
ratio.
Compared to other throttling methods already exist in the kernel,
such as ACPI PAD (taking CPUs offline) and clock modulation, this is often
more efficient in terms of performance per watt.
Please refer to Documentation/thermal/intel_powerclamp.txt for more details.
Signed-off-by: Arjan van de Ven <arjan@linux.intel.com>
Signed-off-by: Jacob Pan <jacob.jun.pan@linux.intel.com>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
This patch supports exynos's emulation mode with newly created sysfs node.
Exynos 4x12 (4212, 4412) and 5 series provide emulation mode for thermal
management unit. Thermal emulation mode supports software debug for TMU's
operation. User can set temperature manually with software code and TMU
will read current temperature from user value not from sensor's value.
This patch includes also documentary placed under Documentation/thermal/.
Signed-off-by: Jonghwa Lee <jonghwa3.lee@samsung.com>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Pull trivial branch from Jiri Kosina:
"Usual stuff -- comment/printk typo fixes, documentation updates, dead
code elimination."
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial: (39 commits)
HOWTO: fix double words typo
x86 mtrr: fix comment typo in mtrr_bp_init
propagate name change to comments in kernel source
doc: Update the name of profiling based on sysfs
treewide: Fix typos in various drivers
treewide: Fix typos in various Kconfig
wireless: mwifiex: Fix typo in wireless/mwifiex driver
messages: i2o: Fix typo in messages/i2o
scripts/kernel-doc: check that non-void fcts describe their return value
Kernel-doc: Convention: Use a "Return" section to describe return values
radeon: Fix typo and copy/paste error in comments
doc: Remove unnecessary declarations from Documentation/accounting/getdelays.c
various: Fix spelling of "asynchronous" in comments.
Fix misspellings of "whether" in comments.
eisa: Fix spelling of "asynchronous".
various: Fix spelling of "registered" in comments.
doc: fix quite a few typos within Documentation
target: iscsi: fix comment typos in target/iscsi drivers
treewide: fix typo of "suport" in various comments and Kconfig
treewide: fix typo of "suppport" in various comments
...
As thermal drivers can be built as modules and also
the thermal framework itself, building cpu cooling
only as built-in can cause linking errors. For instance:
* Generic Thermal sysfs driver
*
Generic Thermal sysfs driver (THERMAL) [M/n/y/?] m
generic cpu cooling support (CPU_THERMAL) [N/y/?] (NEW) y
with the following drive:
CONFIG_OMAP_BANDGAP=m
generates:
ERROR: "cpufreq_cooling_unregister" [drivers/staging/omap-thermal/omap-thermal.ko] undefined!
ERROR: "cpufreq_cooling_register" [drivers/staging/omap-thermal/omap-thermal.ko] undefined!
This patch changes cpu cooling driver to allow it
to be built as module.
Reported-by: Enric Balletbo i Serra <eballetbo@gmail.com>
Signed-off-by: Eduardo Valentin <eduardo.valentin@ti.com>
Reviewed-by: Durgadoss R <durgadoss.r@intel.com>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
This driver is based on the thermal management framework in thermal_sys.c. A
thermal zone device is created with the trip points to which cooling devices
can be bound, the current cooling device is cpufreq, e.g. CPU frequency is
clipped down to cool the CPU, and other cooling devices can be added and bound
to the trip points dynamically. The platform specific PRCMU interrupts are
used to active thermal update when trip points are reached.
Signed-off-by: hongbo.zhang <hongbo.zhang@linaro.com>
Reviewed-by: Viresh Kumar <viresh.kumar@linaro.org>
Reviewed-by: Francesco Lavra <francescolavra.fl@gmail.com>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
This patch provides option to choose the default thermal
governor. If no option is provided, the step_wise
governor is selected by default.
Signed-off-by: Durgadoss R <durgadoss.r@intel.com>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
This patch registers a governor which will let the
user land manage the platform thermals. Whenever a
trip happens, this governor just notifies the user
space using kobj_uevent().
Signed-off-by: Durgadoss R <durgadoss.r@intel.com>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
This patch adds a simple step_wise governor to the
generic thermal layer. This algorithm throttles the
cooling devices in a linear fashion. If the 'trend'
is heating, it throttles by one step. And if the
thermal trend is cooling it de-throttles by one step.
This actually moves the throttling logic from thermal_sys.c
and puts inside step_wise.c, without any change.
Signed-off-by: Durgadoss R <durgadoss.r@intel.com>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
This patch introduces a simple 'weight' based
governor named fair_share governor. Whenever the
thermal framework gets notified of the trip point
violation, this governor (if configured), throttles
the cooling devices associated with a thermal zone.
This mapping between a thermal zone and a cooling device
and the effectiveness of cooling are provided in the
platform layer.
Signed-off-by: Durgadoss R <durgadoss.r@intel.com>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Commit 0236141837 ("thermal: add generic cpufreq cooling
implementation") requires cpufreq_frequency_get_table(), but that
function is only defined for CONFIG_CPU_FREQ_TABLE resulting in the
following build error:
drivers/built-in.o: In function `cpufreq_get_max_state':
drivers/thermal/cpu_cooling.c:259: undefined reference to `cpufreq_frequency_get_table'
drivers/built-in.o: In function `get_cpu_frequency':
drivers/thermal/cpu_cooling.c:129: undefined reference to `cpufreq_frequency_get_table'
Fix it by selecting CONFIG_CPU_FREQ_TABLE for such a configuration.
It turns out CONFIG_EXYNOS_THERMAL also needs CONFIG_CPU_FREQ_TABLE, so
select it there as well.
Signed-off-by: David Rientjes <rientjes@google.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Insert exynos5 TMU sensor changes into the thermal driver. Some exynos4
changes are made generic for exynos series.
[akpm@linux-foundation.org: fix comment layout]
Signed-off-by: SangWook Ju <sw.ju@samsung.com>
Signed-off-by: Amit Daniel Kachhap <amit.kachhap@linaro.org>
Acked-by: Guenter Roeck <guenter.roeck@ericsson.com>
Cc: Durgadoss <durgadoss.r@intel.com>
Cc: Len Brown <lenb@kernel.org>
Cc: Jean Delvare <khali@linux-fr.org>
Cc: Kyungmin Park <kmpark@infradead.org>
Cc: Kukjin Kim <kgene.kim@samsung.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Amit Daniel Kachhap <amit.daniel@samsung.com>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
This movement is needed because the hwmon entries and corresponding sysfs
interface is a duplicate of utilities already provided by
driver/thermal/thermal_sys.c. The goal is to place it in thermal folder
and add necessary functions to use the in-kernel thermal interfaces.
Signed-off-by: Amit Daniel Kachhap <amit.kachhap@linaro.org>
Acked-by: Guenter Roeck <guenter.roeck@ericsson.com>
Cc: SangWook Ju <sw.ju@samsung.com>
Cc: Durgadoss <durgadoss.r@intel.com>
Cc: Len Brown <lenb@kernel.org>
Cc: Jean Delvare <khali@linux-fr.org>
Cc: Kyungmin Park <kmpark@infradead.org>
Cc: Kukjin Kim <kgene.kim@samsung.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Amit Daniel Kachhap <amit.daniel@samsung.com>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
This patchset introduces a new generic cooling device based on cpufreq
that can be used on non-ACPI platforms. As a proof of concept, we have
drivers for the following platforms using this mechanism now:
* Samsung Exynos (Exynos4 and Exynos5) in the current patchset.
* Freescale i.MX (git://git.linaro.org/people/amitdanielk/linux.git imx6q_thermal)
There is a small change in cpufreq cooling registration APIs, so a minor
change is needed for Freescale platforms.
Brief Description:
1) The generic cooling devices code is placed inside driver/thermal/*
as placing inside acpi folder will need un-necessary enabling of acpi
code. This code is architecture independent.
2) This patchset adds generic cpu cooling low level implementation
through frequency clipping. In future, other cpu related cooling
devices may be added here. An ACPI version of this already exists
(drivers/acpi/processor_thermal.c) .But this will be useful for
platforms like ARM using the generic thermal interface along with the
generic cpu cooling devices. The cooling device registration API's
return cooling device pointers which can be easily binded with the
thermal zone trip points. The important APIs exposed are,
a) struct thermal_cooling_device *cpufreq_cooling_register(
struct cpumask *clip_cpus)
b) void cpufreq_cooling_unregister(struct thermal_cooling_device *cdev)
3) Samsung exynos platform thermal implementation is done using the
generic cpu cooling APIs and the new trip type. The temperature sensor
driver present in the hwmon folder(registered as hwmon driver) is moved
to thermal folder and registered as a thermal driver.
A simple data/control flow diagrams is shown below,
Core Linux thermal <-----> Exynos thermal interface <----- Temperature Sensor
| |
\|/ |
Cpufreq cooling device <---------------
TODO:
*Will send the DT enablement patches later after the driver is merged.
This patch:
Add support for generic cpu thermal cooling low level implementations
using frequency scaling up/down based on the registration parameters.
Different cpu related cooling devices can be registered by the user and
the binding of these cooling devices to the corresponding trip points can
be easily done as the registration APIs return the cooling device pointer.
The user of these APIs are responsible for passing clipping frequency .
The drivers can also register to recieve notification about any cooling
action called.
[akpm@linux-foundation.org: fix comment layout]
Signed-off-by: Amit Daniel Kachhap <amit.kachhap@linaro.org>
Cc: Guenter Roeck <guenter.roeck@ericsson.com>
Cc: SangWook Ju <sw.ju@samsung.com>
Cc: Durgadoss <durgadoss.r@intel.com>
Cc: Len Brown <lenb@kernel.org>
Cc: Jean Delvare <khali@linux-fr.org>
Cc: Kyungmin Park <kmpark@infradead.org>
Cc: Kukjin Kim <kgene.kim@samsung.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Amit Daniel Kachhap <amit.daniel@samsung.com>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
This patch add basic Renesas R-Car thermal sensor support.
It was tested on R-Car H1 Marzen board.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Cc: Len Brown <len.brown@intel.com>
Cc: Joe Perches <joe@perches.com>
Cc: Jean Delvare <khali@linux-fr.org>
Cc: Guenter Roeck <guenter.roeck@ericsson.com>
Cc: Magnus Damm <magnus.damm@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
SPEAr platforms now support DT and so must convert all drivers to support
DT. This patch adds DT probing support for SPEAr thermal sensor driver
and updates its documentation too.
Also, as SPEAr is the only user of this driver and is only available with
DT, make this an only DT driver. So, platform_data is completely removed
and passed via DT now.
Signed-off-by: Viresh Kumar <viresh.kumar@st.com>
Cc: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Vincenzo Frascino <vincenzo.frascino@st.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Len Brown <len.brown@intel.com>
ST's SPEAr13xx machines are based on CortexA9 ARM processors. These
machines contain a thermal sensor for junction temperature monitoring.
This patch adds support for this thermal sensor in existing thermal
framework.
[akpm@linux-foundation.org: little code cleanup]
[akpm@linux-foundation.org: print the pointer correctly]
[viresh.kumar@st.com: thermal/spear_thermal: add compilation dependency on PLAT_SPEAR]
Signed-off-by: Vincenzo Frascino <vincenzo.frascino@st.com>
Signed-off-by: Viresh Kumar <viresh.kumar@st.com>
Signed-off-by: Viresh Kumar <viresh.kumar@st.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Len Brown <len.brown@intel.com>
It's about time to revert 16d7523973 ("thermal: Create
CONFIG_THERMAL_HWMON=n"). Anybody running a kernel >= 2.6.40 would also
be running a recent enough version of lm-sensors.
Actually having CONFIG_THERMAL_HWMON is pretty convenient so instead of
dropping it, we keep it but hide it.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Rene Herman <rene.herman@gmail.com>
Acked-by: Guenter Roeck <guenter.roeck@ericsson.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Len Brown <len.brown@intel.com>
Several ACPI drivers fail to build if CONFIG_NET is unset, because
they refer to things depending on CONFIG_THERMAL that in turn depends
on CONFIG_NET. However, CONFIG_THERMAL doesn't really need to depend
on CONFIG_NET, because the only part of it requiring CONFIG_NET is
the netlink interface in thermal_sys.c.
Put the netlink interface in thermal_sys.c under #ifdef CONFIG_NET
and remove the dependency of CONFIG_THERMAL on CONFIG_NET from
drivers/thermal/Kconfig.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: Randy Dunlap <randy.dunlap@oracle.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Len Brown <lenb@kernel.org>
Cc: Stephen Rothwell <sfr@canb.auug.org.au>
Cc: Luming Yu <luming.yu@intel.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch adds event notification support to the generic
thermal sysfs framework in the kernel. The notification is in the
form of a netlink event.
Signed-off-by: R.Durgadoss <durgadoss.r@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Otherwise THERMAL_HWMON can be selected when HWMON=n and THERMAL=n, which
fails to build.
Signed-off-by: Jan Beulich <jbeulich@novell.com>
Cc: Zhang Rui <rui.zhang@intel.com>
Cc: Matthew Garrett <mjg@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Len Brown <len.brown@intel.com>
A bug in libsensors <= 2.10.6 is exposed
when this new hwmon I/F is enabled.
Create CONFIG_THERMAL_HWMON=n
until some time after libsensors 2.10.7 ships
so those users can run the latest kernel.
libsensors 3.x is already fixed -- those users
can use CONFIG_THERMAL_HWMON=y now.
Signed-off-by: Rene Herman <rene.herman@gmail.com>
Acked-by: Mark M. Hoffman <mhoffman@lightlink.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Build the generic thermal driver as module "thermal_sys".
Make ACPI thermal, video, processor and fan SELECT the generic
thermal driver, as these drivers rely on it to build the sysfs I/F.
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Acked-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Len Brown <len.brown@intel.com>
The generic thermal I/F gets selected by ACPI_THERMAL --
its only current customer.
it doesn't need to clutter other configs by default.
Signed-off-by: Len Brown <len.brown@intel.com>
This reverts commit 3152fb9f11.
This broke libsensors.
Acked-by: Zhang Rui <rui.zhang@intel.com>
Acked-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Len Brown <len.brown@intel.com>
The Generic Thermal sysfs driver for thermal management.
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Signed-off-by: Thomas Sujith <sujith.thomas@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Caesar Wang