If we use a combination of VMODE and I2C4 for retention modes,
eventually the off idle power consumption will creep up by about
23mW, even during off mode with I2C4 always staying enabled.
Turns out this is because of erratum i531 "Extra Power Consumed
When Repeated Start Operation Mode Is Enabled on I2C Interface
Dedicated for Smart Reflex (I2C4)" as pointed out by Nishanth
Menon <nm@ti.com>.
Let's fix the issue by adding i2c_cfg_clear_mask for the bits
to clear when initializing the I2C4 adapter so we can clear
SREN bit that drives the I2C4 lines low otherwise when there
is no traffic.
Fixes: 3b8c4ebb76 ("ARM: OMAP3: Fix idle mode signaling for
Cc: stable@vger.kernel.org # v3.16+
sys_clkreq and sys_off_mode")
Cc: Kevin Hilman <khilman@kernel.org>
Cc: Tero Kristo <t-kristo@ti.com>
Reviewed-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The commit 7be914f {ARM: OMAP3: PRM/CM: Cleanup unused header} removed
some of the macros used by the TI DSP/Bridge driver. This fixes the
following build errors when trying to build DSP/Bridge driver (disabled
at present), otherwise results in the following build errors:
drivers/staging/tidspbridge/core/tiomap3430.c:531:31: error: 'OMAP3430_AUTO_IVA2_DPLL_SHIFT' undeclared (first use in this function)
drivers/staging/tidspbridge/core/tiomap3430.c:531:31: note: each undeclared identifier is reported only once for each function it appears in
make[3]: *** [drivers/staging/tidspbridge/core/tiomap3430.o] Error 1
make[3]: *** Waiting for unfinished jobs....
drivers/staging/tidspbridge/core/tiomap_io.c: In function 'sm_interrupt_dsp':
drivers/staging/tidspbridge/core/tiomap_io.c:404:31: error: 'OMAP3430_AUTO_IVA2_DPLL_SHIFT' undeclared (first use in this function)
drivers/staging/tidspbridge/core/tiomap_io.c:404:31: note: each undeclared identifier is reported only once for each function it appears in
drivers/staging/tidspbridge/core/tiomap_io.c:414:12: error: 'OMAP3430_IVA2_DPLL_FREQSEL_SHIFT' undeclared (first use in this function)
drivers/staging/tidspbridge/core/tiomap_io.c:415:12: error: 'OMAP3430_EN_IVA2_DPLL_SHIFT' undeclared (first use in this function)
make[3]: *** [drivers/staging/tidspbridge/core/tiomap_io.o] Error 1
drivers/staging/tidspbridge/core/tiomap3430_pwr.c: In function 'dsp_clk_wakeup_event_ctrl':
drivers/staging/tidspbridge/core/tiomap3430_pwr.c:442:19: error: 'OMAP3430_GRPSEL_GPT5_MASK' undeclared (first use in this function)
drivers/staging/tidspbridge/core/tiomap3430_pwr.c:442:19: note: each undeclared identifier is reported only once for each function it appears in
drivers/staging/tidspbridge/core/tiomap3430_pwr.c:455:19: error: 'OMAP3430_GRPSEL_GPT6_MASK' undeclared (first use in this function)
drivers/staging/tidspbridge/core/tiomap3430_pwr.c:468:19: error: 'OMAP3430_GRPSEL_GPT7_MASK' undeclared (first use in this function)
drivers/staging/tidspbridge/core/tiomap3430_pwr.c:481:19: error: 'OMAP3430_GRPSEL_GPT8_MASK' undeclared (first use in this function)
drivers/staging/tidspbridge/core/tiomap3430_pwr.c:494:19: error: 'OMAP3430_GRPSEL_MCBSP1_MASK' undeclared (first use in this function)
drivers/staging/tidspbridge/core/tiomap3430_pwr.c:546:19: error: 'OMAP3430_GRPSEL_MCBSP5_MASK' undeclared (first use in this function)
make[3]: *** [drivers/staging/tidspbridge/core/tiomap3430_pwr.o] Error 1
make[2]: *** [drivers/staging/tidspbridge] Error 2
Fixes: 7be914f (ARM: OMAP3: PRM/CM: Cleanup unused header)
Cc: Rajendra Nayak <rnayak@ti.com>
Cc: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
While debugging legacy mode vs device tree booted PM regressions,
I noticed that omap3 is not toggling sys_clkreq and sys_off_mode
pins like it should.
The sys_clkreq and sys_off_mode pins are not toggling because of
the following issues:
1. The default polarity for the sys_off_mode pin is wrong.
OFFMODE_POL needs to be cleared for sys_off_mode to go down when
hitting off-idle, while CLKREQ_POL needs to be set so sys_clkreq
goes down when hitting retention.
2. The values for voltctrl register need to be updated dynamically.
We need to set either the retention idle bits, or off idle bits
in the voltctrl register depending the idle mode we're targeting
to hit.
Let's fix these two issues as otherwise the system will just
hang if any twl4030 PMIC idle scripts are loaded. The only case
where the system does not hang is if only retention idle over I2C4
is configured by the bootloader.
Note that even without the twl4030 PMIC scripts, these fixes will
do the proper signaling of sys_clkreq and sys_off_mode pins, so
the fixes are needed to fix monitoring of PM states with LEDs or
an oscilloscope.
Cc: Kevin Hilman <khilman@linaro.org>
Cc: Nishanth Menon <nm@ti.com>
Cc: Paul Walmsley <paul@pwsan.com>
Cc: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Cleanup unused parts of the PRM and CM regbit headers leaving only whats
used.
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
The patch is the output from a python script which converts
from the old OMAP clk format to COMMON clk format using a
JSON parser in between which was developed by Paul Walmsley.
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
[paul@pwsan.com: AM3517/05: dropped bogus hsotgusb "ick" and "fck"
clkdev aliases; added hsotgusb_fck alias; added emac_ick and emac_fck
aliases; replace omap2_init_clksel_parent() with
omap2_clksel_find_parent_index(); reflow macros and parent name
lists; add clkdm_name argument to DEFINE_STRUCT_CLK_HW_OMAP macros]
Signed-off-by: Mike Turquette <mturquette@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
The OMAP watchdog timer driver needs to determine what caused the SoC
to reset for its GETBOOTSTATUS ioctl. So, define a set of standard
reset sources across OMAP SoCs. For OMAP2xxx, 3xxx, and 4xxx SoCs,
define mappings from the SoC-specific reset source register bits to
the standardized reset source IDs. Create SoC-specific PRM functions
that read the appropriate per-SoC register and use the mapping to
return the standardized reset bits. Register the SoC-specific PRM
functions with the common PRM code via prm_register(). Create a
function in the common PRM code, prm_read_reset_sources(), that
calls the SoC-specific function, registered during boot.
This patch does not yet handle some SoCs, such as AM33xx. Those SoCs
were not handled by the code this will replace.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Move OMAP3xxx-specific PRM functions & macros into prm3xxx.[ch] and
OMAP2xxx-specific macros into prm2xxx.h. (prm2xxx.c will be created
by a subsequent patch when it's needed.) Move basic PRM register
access functions into static inline functions in prm2xxx_3xxx.h, leaving
only OMAP2/3 hardreset functions in prm2xxx_3xxx.c.
Also clarify the initcall function naming to reinforce that this code
is specifically for the PRM IP block.
This is in preparation for the upcoming powerdomain series and the
upcoming move of this code to drivers/.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Reviewed-by: Russ Dill <Russ.Dill@ti.com>
Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
In preparation for adding OMAP4-specific PRCM accessor/mutator
functions, split the existing OMAP2/3 PRCM code into OMAP2/3-specific
files. Most of what was in mach-omap2/{cm,prm}.{c,h} has now been
moved into mach-omap2/{cm,prm}2xxx_3xxx.{c,h}, since it was
OMAP2xxx/3xxx-specific.
This process also requires the #includes in each of these files to be
changed to reference the new file name. As part of doing so, add some
comments into plat-omap/sram.c and plat-omap/mcbsp.c, which use
"sideways includes", to indicate that these users of the PRM/CM includes
should not be doing so.
Thanks to Felipe Contreras <felipe.contreras@gmail.com> for comments on this
patch.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Jarkko Nikula <jhnikula@gmail.com>
Cc: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Cc: Liam Girdwood <lrg@slimlogic.co.uk>
Cc: Omar Ramirez Luna <omar.ramirez@ti.com>
Acked-by: Omar Ramirez Luna <omar.ramirez@ti.com>
Cc: Felipe Contreras <felipe.contreras@gmail.com>
Acked-by: Felipe Contreras <felipe.contreras@gmail.com>
Cc: Greg Kroah-Hartman <greg@kroah.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Reviewed-by: Kevin Hilman <khilman@deeprootsystems.com>
Tested-by: Kevin Hilman <khilman@deeprootsystems.com>
Tested-by: Rajendra Nayak <rnayak@ti.com>
Tested-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Add hwmod structures for I2C controllers on OMAP3430.
This patch was developed in collaboration with Paul Walmsley
<paul@pwsan.com>.
OMAP3 fixes for correct IDLEST bit monitoring from
G, Manjunath Kondaiah <manjugk@ti.com>
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: G, Manjunath Kondaiah <manjugk@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
To standarize among other uarts (1 to 3), we shall now:
- Enable uart4 autodile bit.
- Enable uart4 wakeup in PER.
- Allow uart4 to wakeup the MPU.
Signed-off-by: Sergio Aguirre <saaguirre@ti.com>
Signed-off-by: Govindraj.R <govindraj.raja@ti.com>
Acked-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Fix all of the remaining OMAP3 PRCM register shift/bitmask macros that
did not use the _SHIFT/_MASK suffixes to use them. This makes the use
of these macros consistent. It is intended to reduce error, as code
can be inspected visually by reviewers to ensure that bitshifts and
bitmasks are used in the appropriate places.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Kevin Hilman <khilman@deeprootsystems.com>
OMAP 3430 ES3.1 chips have a separate bit for IO daisy-chain
wake up enabling. It needs to be enabled when entering
retention or off state, otherwise waking up might not work
in all situations.
Signed-off-by: Kalle Jokiniemi <kalle.jokiniemi@digia.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
The OMAP3430ES2_SAVEANDRESTORE_SHIFT macro is used
by powerdomain code in
"1 << OMAP3430ES2_SAVEANDRESTORE_SHIFT" manner, but
the definition was also (1 << 4), meaning we actually
modified bit 16. So the definition needs to be 4.
This fixes also a cold reset HW bug in OMAP3430 ES3.x
where some of the efuse bits are not isolated during
wake-up from off mode. This can cause randomish
cold resets with off mode. Enabling the USBTLL hardware
SAVEANDRESTORE causes the core power up assert to be
delayed in a way that we will not get faulty values
when boot ROM is reading the unisolated registers.
Signed-off-by: Kalle Jokiniemi <kalle.jokiniemi@digia.com>
Acked-by: Kevin Hilman <khilman@deeprootsystems.com>
Acked-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Jouni Hogander <jouni.hogander@nokia.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This patch adds register access for 34xx power and clock management.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Tony Lindgren