Implement much easier and more lightweight locking for
the periodic work. This also removes the last big busywait
loop and replaces it by a sleeping loop.
This patch for b43legacy is patterned aftar the same patch
for b43 by Michael Buesch <mb@bu3sch.de>.
Signed-off-by: Larry Finger <larry.finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This removes the direct call to rfkill on an rfkill event
and replaces it with an input device. This way userspace is also
notified about the event.
This patch is the port to b43legacy of a patch for b43 by Michael Buesch
<mb@bu3sch.de>.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This adds full support for the RFKILL button and the RFKILL LED trigger.
This is a port to b43legacy of a patch by Michael Buesch <mb@bu3sch.de>
for b43.
Signed-off-by: Larry Finger<Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Drive the LEDs through the generic LED triggers.
The patch to b43 by Michael Buesch <mb@bu3sch.de> has been ported to b43legacy.
Signed-off-by: Larry Finger <larry.finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
These drivers pass full mactime information to the stack, make them
indicate this via the new RX_FLAG_TSFT to get mac80211 to show this
information in monitor mode.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix some left-over URLs and ifdefs in b43 and b43legacy drivers.
Signed-off-by: Stefano Brivio <stefano.brivio@polimi.it>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Fix an IRQ race condition in b43legacy. If we call
b43legacy_wireless_core_stop(), it will set the status of the device to
INITIALIZED and the IRQ handler won't care any longer about IRQs, thus the
kernel will disable the IRQ if it's shared (unless we boot it with the
'irqpoll' option). So we must disable IRQs before changing the device
status.
Signed-off-by: Stefano Brivio <stefano.brivio@polimi.it>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Fix possible buffer overrun.
The patch to b43 by Michael Buesch <mb@bu3sch.de> has been ported to
b43legacy.
Signed-off-by: Stefano Brivio <stefano.brivio@polimi.it>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When rounding a relative timeout we need to use round_jiffies_relative().
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Using the Coverity checker, Adrian Bunk found that routine b43legacy_start
could return an unitialized variable. This patch fixes the problem.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Drivers are currently supposed to keep track of monitor
interfaces if they allow so-called "hard" monitor, and
they are also supposed to keep track of multicast etc.
This patch changes that, replaces the set_multicast_list()
callback with a new configure_filter() callback that takes
filter flags (FIF_*) instead of interface flags (IFF_*).
For a driver, this means it should open the filter as much
as necessary to get all frames requested by the filter flags.
Accordingly, the filter flags are named "positively", e.g.
FIF_ALLMULTI.
Multicast filtering is a bit special in that drivers that
have no multicast address filters need to allow multicast
frames through when either the FIF_ALLMULTI flag is set or
when the mc_count value is positive.
At the same time, drivers are no longer notified about
monitor interfaces at all, this means they now need to
implement the start() and stop() callbacks and the new
change_filter_flags() callback. Also, the start()/stop()
ordering changed, start() is now called *before* any
add_interface() as it really should be, and stop() after
any remove_interface().
The patch also changes the behaviour of setting the bssid
to multicast for scanning when IEEE80211_HW_NO_PROBE_FILTERING
is set; the IEEE80211_HW_NO_PROBE_FILTERING flag is removed
and the filter flag FIF_BCN_PRBRESP_PROMISC introduced.
This is a lot more efficient for hardware like b43 that
supports it and other hardware can still set the BSSID
to all-ones.
Driver modifications by Johannes Berg (b43 & iwlwifi), Michael Wu
(rtl8187, adm8211, and p54), Larry Finger (b43legacy), and
Ivo van Doorn (rt2x00).
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Michael Wu <flamingice@sourmilk.net>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This change cleans up the radio-related messages in several ways.
(1) The state of the rfkill switch is assumed to be on, rather than
tested. Now, any user without such a switch will not see any
messages. For devices with such a switch, a message will be
logged only if the initial state is off, or if the switch is toggled.
(2) The routine for testing the switch state is no longer inline.
(3) The LED handling routine is simplified.
(4) The "Radio turned off" message that has confused some users has been
changed to "Radio initialized".
This patch is patterned after a similar change to b43 by Michael Buesch.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This adds support for turning the radio off in software.
That's useful in environments, where you don't want the RF
to radiate any signals, but don't want to bring the interface down.
This patch is based on a similar patch of b43 by Michael Buesch.
Signed-off-by: Larry Finger <larry.finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Larry Finger