If the same virtual LUN is accessed over multiple cards, only accesses
made over the first card will be valid. Accesses made over the second
card will go to the wrong LUN causing data corruption.
This is because the global LUN's mode word was being used to determine
whether the LUN table for that card needs to be programmed. The mode
word would be setup by the first card, causing the LUN table for the
second card to not be programmed.
By unconditionally initializing the LUN table (not depending on the
mode word), the problem is avoided.
Signed-off-by: Matthew R. Ochs <mrochs@linux.vnet.ibm.com>
Signed-off-by: Manoj N. Kumar <manoj@linux.vnet.ibm.com>
Reviewed-by: Brian King <brking@linux.vnet.ibm.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
When a LUN is removed, the sdev that is associated with the LUN
remains intact until its reference count drops to 0. In order
to prevent an sdev from being removed while a context is still
associated with it, obtain an additional reference per-context
for each LUN attached to the context.
This resolves a potential Oops in the release handler when a
dealing with a LUN that has already been removed.
Signed-off-by: Matthew R. Ochs <mrochs@linux.vnet.ibm.com>
Signed-off-by: Manoj N. Kumar <manoj@linux.vnet.ibm.com>
Reviewed-by: Brian King <brking@linux.vnet.ibm.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
The timeout value for read capacity is too small. Certain devices
may take longer to respond and thus the command may prematurely
timeout. Additionally the literal used for the timeout is stale.
Update the timeout to 30 seconds (matches the value used in sd.c)
and rework the timeout literal to a more appropriate description.
Signed-off-by: Matthew R. Ochs <mrochs@linux.vnet.ibm.com>
Signed-off-by: Manoj N. Kumar <manoj@linux.vnet.ibm.com>
Reviewed-by: Brian King <brking@linux.vnet.ibm.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
Magic numbers are not meaningful and can create confusion. As a
remedy, replace them with descriptive literals.
Replace 512 with literal MAX_SECTOR_UNIT.
Replace 5 with literal CMD_RETRIES.
Signed-off-by: Matthew R. Ochs <mrochs@linux.vnet.ibm.com>
Signed-off-by: Manoj N. Kumar <manoj@linux.vnet.ibm.com>
Reviewed-by: Brian King <brking@linux.vnet.ibm.com>
Reviewed-by: Andrew Donnellan <andrew.donnellan@au1.ibm.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
If two concurrent MANAGE_LUN ioctls are issued with the same
WWID parameter, it would result in an incorrect value of port_sel.
This is because port_sel is modified without any locks being
held. If the first caller stalls after the return from
find_and_create_lun(), the value of port_sel will be set
incorrectly to indicate a single port, though in this case
it should have been set to both ports.
To fix, use the global mutex to serialize the lookup of the
WWID and the subsequent modification of port_sel.
Signed-off-by: Matthew R. Ochs <mrochs@linux.vnet.ibm.com>
Signed-off-by: Manoj N. Kumar <manoj@linux.vnet.ibm.com>
Reviewed-by: Brian King <brking@linux.vnet.ibm.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
The "compatible" matching algorithm used for looking up old-style
blacklist entries in a scsi_dev_info_list is buggy. The core of the
algorithm looks like this:
if (memcmp(devinfo->vendor, vendor,
min(max, strlen(devinfo->vendor))))
/* not a match */
where max is the length of the device's vendor string after leading
spaces have been removed but trailing spaces have not. Because of the
min() computation, either entry could be a proper substring of the
other and the code would still think that they match.
In the case originally reported, the device's vendor and product
strings were "Inateck " and " ". These matched against
the following entry in the global device list:
{"", "Scanner", "1.80", BLIST_NOLUN}
because "" is a substring of "Inateck " and "" (the result of removing
leading spaces from the device's product string) is a substring of
"Scanner". The mistaken match prevented the system from scanning and
finding the device's second Logical Unit.
This patch fixes the problem by making two changes. First, the code
for leading-space removal is hoisted out of the loop. (This means it
will sometimes run unnecessarily, but since a large percentage of all
lookups involve the "compatible" entries in global device list, this
should be an overall improvement.) Second and more importantly, the
patch removes trailing spaces and adds a check to verify that the two
resulting strings are exactly the same length. This prevents matches
where one entry is a proper substring of the other.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Reported-by: Giulio Bernardi <ugilio@gmail.com>
Tested-by: Giulio Bernardi <ugilio@gmail.com>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
In drivers/scsi/scsi_devinfo.c, the scsi_dev_info_list_del_keyed() and
scsi_get_device_flags_keyed() routines contain a large amount of
duplicate code for finding vendor/product matches in a
scsi_dev_info_list. This patch factors out the duplicate code and
puts it in a separate function, scsi_dev_info_list_find().
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Suggested-by: Giulio Bernardi <ugilio@gmail.com>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
the kernel prints some warnings when compiled with CONFIG_DMA_API_DEBUG.
This is because the fnic driver doesn't check the return value of
pci_map_single().
[ 11.942770] scsi host12: fnic
[ 11.950811] ------------[ cut here ]------------
[ 11.950818] WARNING: at lib/dma-debug.c:937 check_unmap+0x47b/0x920()
[ 11.950821] fnic 0000:0c:00.0: DMA-API: device driver failed to check map error[device address=0x0000002020a30040] [size=44 bytes] [mapped as single]
Signed-off-by: Maurizio Lombardi <mlombard@redhat.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Reviewed By: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
We would like to get the following updates in:
Revert ownership to "Emulex" from "Avago Technologies"
Signed-off-by: Ketan Mukadam <ketan.mukadam@avagotech.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
Do not log error for netevents that need no action such as
NETDEV_REGISTER 0x0005, NETDEV_CHANGEADDR, and NETDEV_CHANGENAME.
It results in logging error messages such as these
[ 35.315872] bnx2fc: Unknown netevent 5
[ 35.315935] bnx2fc: Unknown netevent 8
[ 35.353866] bnx2fc: Unknown netevent 10
and generating bug reports.
Remove logging this message as an ERROR instead of turning them into
either DEBUG or INFO level messages.
Signed-off-by: Shirish Pargaonkar <spargaonkar@suse.com>
Acked-by: Eddie Wai <eddie.wai@broadcom.com>
Acked-by: Chad Dupuis <chad.dupuis@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
Signed-off-by: Dick Kennedy <dick.kennedy@avagotech.com>
Signed-off-by: James Smart <james.smart@avagotech.com>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
Initial link up defaults were not properly being tracked relative to
initial FLOGI or pt2pt PLOGI. Add code to initialize them.
Signed-off-by: Dick Kennedy <dick.kennedy@avagotech.com>
Signed-off-by: James Smart <james.smart@avagotech.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
Forgot to clear FCF Discovery in-progress flag upon FLOGI failures.
Thus we didn't restart FLOGI.
Signed-off-by: Dick Kennedy <dick.kennedy@avagotech.com>
Signed-off-by: James Smart <james.smart@avagotech.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
Fix for discovery failure in PT2PT when FLOGI's ELS ACC response gets aborted
Change login state machine to:
- Restart FLOGI if prior is ABTS'd
- Reject incoming FLOGIs if we have one pending
The above ensures that we always finish FLOGI processing, regardless
of who initated FLOGI, before processing PLOGI's.
Signed-off-by: Dick Kennedy <dick.kennedy@avagotech.com>
Signed-off-by: James Smart <james.smart@avagotech.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
Signed-off-by: Dick Kennedy <dick.kennedy@avagotech.com>
Signed-off-by: James Smart <james.smart@avagotech.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
lpfc_send_rscn_event() allocates data for sizeof(struct
lpfc_rscn_event_header) + payload_len, but claims that the data has size
of sizeof(struct lpfc_els_event_header) + payload_len. That leads to
buffer overruns.
Signed-off-by: Ales Novak <alnovak@suse.cz>
Signed-off-by: James Smart <james.smart@avagotech.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Reviewed-by: Sebastian Herbszt <herbszt@gmx.de>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
Remove set but not used variables.
Signed-off-by: Sebastian Herbszt <herbszt@gmx.de>
Signed-off-by: James Smart <james.smart@avagotech.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
This makes the function lpfc_sli4_mbox_completion's definition
static now in order to comply with its prototype being also
declared as static too.
Signed-off-by: Nicholas Krause <xerofoify@gmail.com>
Signed-off-by: James Smart <james.smart@avagotech.com>
Reviewed-by: Sebastian Herbszt <herbszt@gmx.de>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
Currently the module parameter lpfc_sg_seg_count does not have effect
for sli3 devices.
In lpfc_sli_driver_resource_setup(), which is used for sli3, the code
writes the configured sg_seg_cnt into lpfc_template.sg_tablesize.
But lpfc_template is the template used for sli4 only. Thus the value should
correctly be written to lpfc_template_s3->sg_tablesize.
This patch is for kernel 4.1-rc5, but is tested with lpfc 10.2.405.26 only.
Signed-off-by: Bodo Stroesser <bstroesser@ts.fujitsu.com>
Signed-off-by: James Smart <james.smart@avagotech.com>
Reviewed-by: Sebastian Herbszt <herbszt@gmx.de>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
kzalloc() returns a void pointer - no need to cast it in
drivers/scsi/lpfc/lpfc_init.c::lpfc_sli_driver_resource_setup()
Signed-off-by: Firo Yang <firogm@gmail.com>
Signed-off-by: James Smart <james.smart@avagotech.com>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
Remove trailing space from model description.
Signed-off-by: Sebastian Herbszt <herbszt@gmx.de>
Signed-off-by: James Smart <james.smart@avagotech.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
3w controller don't dma map small single SGL entry commands but instead
bounce buffer them. Add a helper to identify these commands and don't
call scsi_dma_unmap for them.
Based on an earlier patch from James Bottomley.
Fixes: 118c85 ("3w-9xxx: fix command completion race")
Reported-by: Tóth Attila <atoth@atoth.sote.hu>
Tested-by: Tóth Attila <atoth@atoth.sote.hu>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Acked-by: Adam Radford <aradford@gmail.com>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
This fixes a bug in recent kernels which results in failure to boot
on systems that have multipath SCSI disks. I observed this failure
on a POWER8 server where all the disks are multipath SCSI disks.
The symptoms are several messages like this on the console:
[ 3.018700] device-mapper: table: 253:0: multipath: error attaching hardware handler
[ 3.018828] device-mapper: ioctl: error adding target to table
and the system does not find its disks, and therefore fails to boot.
Bisection revealed that the bug was introduced in commit 566079c849,
"dm-mpath, scsi_dh: request scsi_dh modules in scsi_dh, not dm-mpath".
The specific reason for the failure is that where we previously loaded
the "scsi_dh_alua" module, we are now trying to load the "alua" module,
which doesn't exist.
To fix this, we change the request_module call in scsi_dh_lookup()
to prepend "scsi_dh_" to the name, just like the old code in
drivers/md/dm-mpath.c:parse_hw_handler() used to do.
[jejb: also fixes issue spotted by Sasha Levin that formatting
characters could be passed in via sysfs and cause issues with
request_module()]
Fixes: 566079c849
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
Cc: Sasha Levin <sasha.levin@oracle.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
Connection last_ping is not being updated when iscsi_send_nopout fails.
Not updating the last_ping will cause firing a timer to a past time
(last_ping + ping_tmo < current_time) which triggers an infinite loop of
iscsi_check_transport_timeouts() and hogs the cpu.
Fix this issue by checking the return value of iscsi_send_nopout.
If it fails set the next_timeout to one second later.
Signed-off-by: Ariel Nahum <arieln@mellanox.com>
Signed-off-by: Sagi Grimberg <sagig@mellanox.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
Pull SCSI target updates from Nicholas Bellinger:
"Here are the outstanding target-pending updates for v4.3-rc1.
Mostly bug-fixes and minor changes this round. The fallout from the
big v4.2-rc1 RCU conversion have (thus far) been minimal.
The highlights this round include:
- Move sense handling routines into scsi_common code (Sagi)
- Return ABORTED_COMMAND sense key for PI errors (Sagi)
- Add tpg_enabled_sendtargets attribute for disabled iscsi-target
discovery (David)
- Shrink target struct se_cmd by rearranging fields (Roland)
- Drop iSCSI use of mutex around max_cmd_sn increment (Roland)
- Replace iSCSI __kernel_sockaddr_storage with sockaddr_storage (Andy +
Chris)
- Honor fabric max_data_sg_nents I/O transfer limit (Arun + Himanshu +
nab)
- Fix EXTENDED_COPY >= v4.1 regression OOPsen (Alex + nab)"
* 'for-next' of git://git.kernel.org/pub/scm/linux/kernel/git/nab/target-pending: (37 commits)
target: use stringify.h instead of own definition
target/user: Fix UFLAG_UNKNOWN_OP handling
target: Remove no-op conditional
target/user: Remove unused variable
target: Fix max_cmd_sn increment w/o cmdsn mutex regressions
target: Attach EXTENDED_COPY local I/O descriptors to xcopy_pt_sess
target/qla2xxx: Honor max_data_sg_nents I/O transfer limit
target/iscsi: Replace __kernel_sockaddr_storage with sockaddr_storage
target/iscsi: Replace conn->login_ip with login_sockaddr
target/iscsi: Keep local_ip as the actual sockaddr
target/iscsi: Fix np_ip bracket issue by removing np_ip
target: Drop iSCSI use of mutex around max_cmd_sn increment
qla2xxx: Update tcm_qla2xxx module description to 24xx+
iscsi-target: Add tpg_enabled_sendtargets for disabled discovery
drivers: target: Drop unlikely before IS_ERR(_OR_NULL)
target: check DPO/FUA usage for COMPARE AND WRITE
target: Shrink struct se_cmd by rearranging fields
target: Remove cmd->se_ordered_id (unused except debug log lines)
target: add support for START_STOP_UNIT SCSI opcode
target: improve unsupported opcode message
...
The major pieces of this patch are a set patches facilitating better
integration between scsi and scsi_dh (the device handling layer used by
multi-path; all the dm parts are acked by Mike Snitzer). It also includes
driver updates for mp3sas, scsi_debug and an assortment of bug fixes.
Signed-off-by: James Bottomley <JBottomley@Odin.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iQEcBAABAgAGBQJV8yt5AAoJEDeqqVYsXL0MBsQH+wXvlx3o0BGuz5ZXfIs/RxzI
MwGnu1J0LSA9FPakkMUVOBtsxIG+pCV+4eKorQMkfGCKAZ8daaYsyYvSEM2mcqIX
1Y/srEnbzfE94JHbsI2pbiMPkB7QdtW27WjTSjQGgD9igAyVmmITiQJrXbpAlSLF
F6n++9avng+GhjXQ5TF8/y13OYgabIoAPM1j4B/ut/Ok8ReruBvMBnOla5w5RMKR
rBZKTZfUwvX5S0cuREwj8tFsRVUgdBNSrcGswFJrZo5x9WAsSHLC6+SOLZuUy1vC
ua0tNtEiyXiuR0/jSP9qv7hJ/j0BW+EGdnW6GZEzKpeMK5PxfVspOsbNunUDRsY=
=Y9G1
-----END PGP SIGNATURE-----
Merge tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull second round of SCSI updates from James Bottomley:
"There's one late arriving patch here (added today), fixing a build
issue which the scsi_dh patch set in here uncovered. Other than that,
everything has been incubated in -next and the checkers for a week.
The major pieces of this patch are a set patches facilitating better
integration between scsi and scsi_dh (the device handling layer used
by multi-path; all the dm parts are acked by Mike Snitzer).
This also includes driver updates for mp3sas, scsi_debug and an
assortment of bug fixes"
* tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi: (50 commits)
scsi_dh: fix randconfig build error
scsi: fix scsi_error_handler vs. scsi_host_dev_release race
fcoe: Convert use of __constant_htons to htons
mpt2sas: setpci reset kernel oops fix
pm80xx: Don't override ts->stat on IO_OPEN_CNX_ERROR_HW_RESOURCE_BUSY
lpfc: Fix possible use-after-free and double free in lpfc_mbx_cmpl_rdp_page_a2()
bfa: Fix incorrect de-reference of pointer
bfa: Fix indentation
scsi_transport_sas: Remove check for SAS expander when querying bay/enclosure IDs.
scsi_debug: resp_request: remove unused variable
scsi_debug: fix REPORT LUNS Well Known LU
scsi_debug: schedule_resp fix input variable check
scsi_debug: make dump_sector static
scsi_debug: vfree is null safe so drop the check
scsi_debug: use SCSI_W_LUN_REPORT_LUNS instead of SAM2_WLUN_REPORT_LUNS;
scsi_debug: define pr_fmt() for consistent logging
mpt2sas: Refcount fw_events and fix unsafe list usage
mpt2sas: Refcount sas_device objects and fix unsafe list usage
scsi_dh: return SCSI_DH_NOTCONN in scsi_dh_activate()
scsi_dh: don't allow to detach device handlers at runtime
...
This patch adds an optional fabric driver provided SGL limit
that target-core will honor as it's own internal I/O maximum
transfer length limit, as exposed by EVPD=0xb0 block limits
parameters.
This is required for handling cases when host I/O transfer
length exceeds the requested EVPD block limits maximum
transfer length. The initial user of this logic is qla2xxx,
so that we can avoid having to reject I/Os from some legacy
FC hosts where EVPD=0xb0 parameters are not honored.
When se_cmd payload length exceeds the provided limit in
target_check_max_data_sg_nents() code, se_cmd->data_length +
se_cmd->prot_length are reset with se_cmd->residual_count
plus underflow bit for outgoing TFO response callbacks.
It also checks for existing CDB level underflow + overflow
and recalculates final residual_count as necessary.
Note this patch currently assumes 1:1 mapping of PAGE_SIZE
per struct scatterlist entry.
Reported-by: Craig Watson <craig.watson@vanguard-rugged.com>
Cc: Craig Watson <craig.watson@vanguard-rugged.com>
Tested-by: Himanshu Madhani <himanshu.madhani@qlogic.com>
Cc: Roland Dreier <roland@purestorage.com>
Cc: Arun Easi <arun.easi@qlogic.com>
Cc: Giridhar Malavali <giridhar.malavali@qlogic.com>
Cc: Andrew Vasquez <andrew.vasquez@qlogic.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Hannes Reinecke <hare@suse.de>
Cc: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
- Use the correct GFN/BFN terms more consistently.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJV8VRMAAoJEFxbo/MsZsTRiGQH/i/jrAJUJfrFC2PINaA2gDwe
O0dlrkCiSgAYChGmxxxXZQSPM5Po5+EbT/dLjZ/uvSooeorM9RYY/mFo7ut/qLep
4pyQUuwGtebWGBZTrj9sygUVXVhgJnyoZxskNUbhj9zvP7hb9++IiI78mzne6cpj
lCh/7Z2dgpfRcKlNRu+qpzP79Uc7OqIfDK+IZLrQKlXa7IQDJTQYoRjbKpfCtmMV
BEG3kN9ESx5tLzYiAfxvaxVXl9WQFEoktqe9V8IgOQlVRLgJ2DQWS6vmraGrokWM
3HDOCHtRCXlPhu1Vnrp0R9OgqWbz8FJnmVAndXT8r3Nsjjmd0aLwhJx7YAReO/4=
=JDia
-----END PGP SIGNATURE-----
Merge tag 'for-linus-4.3-rc0b-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip
Pull xen terminology fixes from David Vrabel:
"Use the correct GFN/BFN terms more consistently"
* tag 'for-linus-4.3-rc0b-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip:
xen/xenbus: Rename the variable xen_store_mfn to xen_store_gfn
xen/privcmd: Further s/MFN/GFN/ clean-up
hvc/xen: Further s/MFN/GFN clean-up
video/xen-fbfront: Further s/MFN/GFN clean-up
xen/tmem: Use xen_page_to_gfn rather than pfn_to_gfn
xen: Use correctly the Xen memory terminologies
arm/xen: implement correctly pfn_to_mfn
xen: Make clear that swiotlb and biomerge are dealing with DMA address
1/ Introduce ZONE_DEVICE and devm_memremap_pages() as a generic
mechanism for adding device-driver-discovered memory regions to the
kernel's direct map. This facility is used by the pmem driver to
enable pfn_to_page() operations on the page frames returned by DAX
('direct_access' in 'struct block_device_operations'). For now, the
'memmap' allocation for these "device" pages comes from "System
RAM". Support for allocating the memmap from device memory will
arrive in a later kernel.
2/ Introduce memremap() to replace usages of ioremap_cache() and
ioremap_wt(). memremap() drops the __iomem annotation for these
mappings to memory that do not have i/o side effects. The
replacement of ioremap_cache() with memremap() is limited to the
pmem driver to ease merging the api change in v4.3. Completion of
the conversion is targeted for v4.4.
3/ Similar to the usage of memcpy_to_pmem() + wmb_pmem() in the pmem
driver, update the VFS DAX implementation and PMEM api to provide
persistence guarantees for kernel operations on a DAX mapping.
4/ Convert the ACPI NFIT 'BLK' driver to map the block apertures as
cacheable to improve performance.
5/ Miscellaneous updates and fixes to libnvdimm including support
for issuing "address range scrub" commands, clarifying the optimal
'sector size' of pmem devices, a clarification of the usage of the
ACPI '_STA' (status) property for DIMM devices, and other minor
fixes.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=o57/
-----END PGP SIGNATURE-----
Merge tag 'libnvdimm-for-4.3' of git://git.kernel.org/pub/scm/linux/kernel/git/nvdimm/nvdimm
Pull libnvdimm updates from Dan Williams:
"This update has successfully completed a 0day-kbuild run and has
appeared in a linux-next release. The changes outside of the typical
drivers/nvdimm/ and drivers/acpi/nfit.[ch] paths are related to the
removal of IORESOURCE_CACHEABLE, the introduction of memremap(), and
the introduction of ZONE_DEVICE + devm_memremap_pages().
Summary:
- Introduce ZONE_DEVICE and devm_memremap_pages() as a generic
mechanism for adding device-driver-discovered memory regions to the
kernel's direct map.
This facility is used by the pmem driver to enable pfn_to_page()
operations on the page frames returned by DAX ('direct_access' in
'struct block_device_operations').
For now, the 'memmap' allocation for these "device" pages comes
from "System RAM". Support for allocating the memmap from device
memory will arrive in a later kernel.
- Introduce memremap() to replace usages of ioremap_cache() and
ioremap_wt(). memremap() drops the __iomem annotation for these
mappings to memory that do not have i/o side effects. The
replacement of ioremap_cache() with memremap() is limited to the
pmem driver to ease merging the api change in v4.3.
Completion of the conversion is targeted for v4.4.
- Similar to the usage of memcpy_to_pmem() + wmb_pmem() in the pmem
driver, update the VFS DAX implementation and PMEM api to provide
persistence guarantees for kernel operations on a DAX mapping.
- Convert the ACPI NFIT 'BLK' driver to map the block apertures as
cacheable to improve performance.
- Miscellaneous updates and fixes to libnvdimm including support for
issuing "address range scrub" commands, clarifying the optimal
'sector size' of pmem devices, a clarification of the usage of the
ACPI '_STA' (status) property for DIMM devices, and other minor
fixes"
* tag 'libnvdimm-for-4.3' of git://git.kernel.org/pub/scm/linux/kernel/git/nvdimm/nvdimm: (34 commits)
libnvdimm, pmem: direct map legacy pmem by default
libnvdimm, pmem: 'struct page' for pmem
libnvdimm, pfn: 'struct page' provider infrastructure
x86, pmem: clarify that ARCH_HAS_PMEM_API implies PMEM mapped WB
add devm_memremap_pages
mm: ZONE_DEVICE for "device memory"
mm: move __phys_to_pfn and __pfn_to_phys to asm/generic/memory_model.h
dax: drop size parameter to ->direct_access()
nd_blk: change aperture mapping from WC to WB
nvdimm: change to use generic kvfree()
pmem, dax: have direct_access use __pmem annotation
dax: update I/O path to do proper PMEM flushing
pmem: add copy_from_iter_pmem() and clear_pmem()
pmem, x86: clean up conditional pmem includes
pmem: remove layer when calling arch_has_wmb_pmem()
pmem, x86: move x86 PMEM API to new pmem.h header
libnvdimm, e820: make CONFIG_X86_PMEM_LEGACY a tristate option
pmem: switch to devm_ allocations
devres: add devm_memremap
libnvdimm, btt: write and validate parent_uuid
...
Based on include/xen/mm.h [1], Linux is mistakenly using MFN when GFN
is meant, I suspect this is because the first support for Xen was for
PV. This resulted in some misimplementation of helpers on ARM and
confused developers about the expected behavior.
For instance, with pfn_to_mfn, we expect to get an MFN based on the name.
Although, if we look at the implementation on x86, it's returning a GFN.
For clarity and avoid new confusion, replace any reference to mfn with
gfn in any helpers used by PV drivers. The x86 code will still keep some
reference of pfn_to_mfn which may be used by all kind of guests
No changes as been made in the hypercall field, even
though they may be invalid, in order to keep the same as the defintion
in xen repo.
Note that page_to_mfn has been renamed to xen_page_to_gfn to avoid a
name to close to the KVM function gfn_to_page.
Take also the opportunity to simplify simple construction such
as pfn_to_mfn(page_to_pfn(page)) into xen_page_to_gfn. More complex clean up
will come in follow-up patches.
[1] http://xenbits.xen.org/gitweb/?p=xen.git;a=commitdiff;h=e758ed14f390342513405dd766e874934573e6cb
Signed-off-by: Julien Grall <julien.grall@citrix.com>
Reviewed-by: Stefano Stabellini <stefano.stabellini@eu.citrix.com>
Acked-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Acked-by: Wei Liu <wei.liu2@citrix.com>
Signed-off-by: David Vrabel <david.vrabel@citrix.com>
b9d5c6b7ef ("[SCSI] cleanup setting task state in
scsi_error_handler()") has introduced a race between scsi_error_handler
and scsi_host_dev_release resulting in the hang when the device goes
away because scsi_error_handler might miss a wake up:
CPU0 CPU1
scsi_error_handler scsi_host_dev_release
kthread_stop()
kthread_should_stop()
test_bit(KTHREAD_SHOULD_STOP)
set_bit(KTHREAD_SHOULD_STOP)
wake_up_process()
wait_for_completion()
set_current_state(TASK_INTERRUPTIBLE)
schedule()
The most straightforward solution seems to be to invert the ordering of
the set_current_state and kthread_should_stop.
The issue has been noticed during reboot test on a 3.0 based kernel but
the current code seems to be affected in the same way.
[jejb: additional comment added]
Cc: <stable@vger.kernel.org> # 3.6+
Reported-and-debugged-by: Mike Mayer <Mike.Meyer@teradata.com>
Signed-off-by: Michal Hocko <mhocko@suse.com>
Reviewed-by: Dan Williams <dan.j.williams@intel.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
In little endian cases, the macro htons unfolds to __swab16 which
provides special case for constants. In big endian cases,
__constant_htons and htons expand directly to the same expression.
So, replace __constant_htons with htons with the goal of getting
rid of the definition of __constant_htons completely.
The semantic patch that performs this transformation is as follows:
@@expression x;@@
- __constant_htons(x)
+ htons(x)
Signed-off-by: Vaishali Thakkar <vthakkar1994@gmail.com>
Acked-by: Vasu Dev <vasu.dev@intel.com>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
mpt2sas: setpci reset on nytro warpdrive card along with sysfs access and
cli ioctl access resulted in kernel oops
1. pci_access_mutex lock added to provide synchronization between IOCTL,
sysfs, PCI resource handling path
2. gioc_lock spinlock to protect list operations over multiple
controllers
>From c53a1cff4c07528b8b9ec7f6716e94950283e8f9 Mon Sep 17 00:00:00 2001
From: Nagarajkumar Narayanan <nagarajkumar.narayanan@seagate.com>
Date: Tue, 18 Aug 2015 11:58:13 +0530
Subject: [PATCH] mpt2sas setpci reset oops fix
In mpt2sas driver due to lack of synchronization between ioctl,
BRM status access through sysfs, pci resource removal kernel oops
happen as ioctl path and BRM status sysfs access path still tries
to access the removed resources
Two locks added to provide syncrhonization
1. pci_access_mutex: Mutex to synchronize ioctl,sysfs show path and
pci resource handling. PCI resource freeing will lead to free
vital hardware/memory resource, which might be in use by cli/sysfs
path functions resulting in Null pointer reference followed by kernel
crash. To avoid the above race condition we use mutex syncrhonization
which ensures the syncrhonization between cli/sysfs_show path
Note: pci_access_mutex is used only if nytro warpdrive cards
(ioc->is_warpdrive based on device id) are used
as we could not test this case with other SAS2 HBA cards
We can remove this check if this behaviour confirmed from other
cards.
2. spinlock on list operations over IOCs
Case: when multiple warpdrive cards(IOCs) are in use
Each IOC will added to the ioc list stucture on initialization.
Watchdog threads run at regular intervals to check IOC for any
fault conditions which will trigger the dead_ioc thread to
deallocate pci resource, resulting deleting the IOC netry from list,
this deletion need to protected by spinlock to enusre that
ioc removal is syncrhonized, if not synchronized it might lead to
list_del corruption as the ioc list is traversed in cli path
Signed-off-by: Nagarajkumar Narayanan <nagarajkumar.narayanan@seagate.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Acked-by: Sreekanth Reddy <sreekanth.reddy@avagotech.com>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
In case psataPayload->status has a status of IO_OPEN_CNX_ERROR_HW_RESOURCE_BUSY
ts->stat gets set to SAS_OPEN_REJECT but a missing 'break' statement causes a
fallthrough to the default handler of the switch statement overriding ts->stat
to SAS_DEV_NO_RESPONSE.
Signed-off-by: Johannes Thumshirn <jthumshirn@suse.de>
Acked-by: Jack Wang <jinpu.wang@profitbricks.com>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
If the bf_get() call in lpfc_mbx_cmpl_rdp_page_a2() does succeeds, execution
continues normally and mp gets kfree()d.
If the subsequent call to lpfc_sli_issue_mbox() fails execution jumps to the
error label where lpfc_mbuf_free() is called with mp->virt and mp->phys as
function arguments. This is the use after free. Following the use after free mp
gets kfree()d again which is a double free.
Signed-off-by: Johannes Thumshirn <jthumshirn@suse.de>
Acked-by: James Smart <james.smart@avagotech.com>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
Dell Server backplanes can report bay/enclosure IDs without an
expander present. This patch allows the bay/enclosure IDs to be
propagaged to sysfs.we
Signed-off-by: Jordan Hargrave <jordan_hargrave@dell.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
Fixes the following warning
In function ‘resp_requests’:
drivers/scsi//scsi_debug.c:1432:15: warning: variable ‘want_dsense’ set
but not used [-Wunused-but-set-variable]
bool dsense, want_dsense;
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
The use case to report 'REPORT LUNS WLUN' described
in scsi_debug documentation didn't work because:
scsi_scan_host_selected() checks for:
lun < shost->max_lun
To fix this we set:
max_lun = SCSI_W_LUN_REPORT_LUNS + 1;
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Acked-by: Douglas Gilbert <dgilbert@interlog.com>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
The function should never be called with cmnd NULL so
put a fat WARN there.
Fix also smatch wraning:
schedule_resp() warn: variable dereferenced before check 'cmnd'
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Acked-by: Douglas Gilbert <dgilbert@interlog.com>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
fixes warning:
warning: no previous prototype for ‘dump_sector’
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Acked-by: Douglas Gilbert <dgilbert@interlog.com>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Acked-by: Douglas Gilbert <dgilbert@interlog.com>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
use SCSI_W_LUN_REPORT_LUNS from scsi.h instead of localy defined
SAM2_WLUN_REPORT_LUNS
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Acked-by: Douglas Gilbert <dgilbert@interlog.com>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
Use pr_fmt with both module name and __func__
Also drop few bare printk leftovers
The log format should stay pretty much intact
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Acked-by: Douglas Gilbert <dgilbert@interlog.com>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
The fw_event_work struct is concurrently referenced at shutdown, so
add a refcount to protect it, and refactor the code to use it.
Additionally, refactor _scsih_fw_event_cleanup_queue() such that it
no longer iterates over the list without holding the lock, since
_firmware_event_work() concurrently deletes items from the list.
Signed-off-by: Calvin Owens <calvinowens@fb.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Nicholas Bellinger <nab@linux-iscsi.org>
Tested-by: Chaitra Basappa <chaitra.basappa@avagotech.com>
Acked-by: Sreekanth Reddy <sreekanth.reddy@avagotech.com>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
These objects can be referenced concurrently throughout the driver, we
need a way to make sure threads can't delete them out from under each
other. This patch adds the refcount, and refactors the code to use it.
Additionally, we cannot iterate over the sas_device_list without
holding the lock, or we risk corrupting random memory if items are
added or deleted as we iterate. This patch refactors _scsih_probe_sas()
to use the sas_device_list in a safe way.
Signed-off-by: Calvin Owens <calvinowens@fb.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Nicholas Bellinger <nab@linux-iscsi.org>
Tested-by: Chaitra Basappa <chaitra.basappa@avagotech.com>
Acked-by: Sreekanth Reddy <sreekanth.reddy@avagotech.com>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
Pull networking updates from David Miller:
"Another merge window, another set of networking changes. I've heard
rumblings that the lightweight tunnels infrastructure has been voted
networking change of the year. But what do I know?
1) Add conntrack support to openvswitch, from Joe Stringer.
2) Initial support for VRF (Virtual Routing and Forwarding), which
allows the segmentation of routing paths without using multiple
devices. There are some semantic kinks to work out still, but
this is a reasonably strong foundation. From David Ahern.
3) Remove spinlock fro act_bpf fast path, from Alexei Starovoitov.
4) Ignore route nexthops with a link down state in ipv6, just like
ipv4. From Andy Gospodarek.
5) Remove spinlock from fast path of act_gact and act_mirred, from
Eric Dumazet.
6) Document the DSA layer, from Florian Fainelli.
7) Add netconsole support to bcmgenet, systemport, and DSA. Also
from Florian Fainelli.
8) Add Mellanox Switch Driver and core infrastructure, from Jiri
Pirko.
9) Add support for "light weight tunnels", which allow for
encapsulation and decapsulation without bearing the overhead of a
full blown netdevice. From Thomas Graf, Jiri Benc, and a cast of
others.
10) Add Identifier Locator Addressing support for ipv6, from Tom
Herbert.
11) Support fragmented SKBs in iwlwifi, from Johannes Berg.
12) Allow perf PMUs to be accessed from eBPF programs, from Kaixu Xia.
13) Add BQL support to 3c59x driver, from Loganaden Velvindron.
14) Stop using a zero TX queue length to mean that a device shouldn't
have a qdisc attached, use an explicit flag instead. From Phil
Sutter.
15) Use generic geneve netdevice infrastructure in openvswitch, from
Pravin B Shelar.
16) Add infrastructure to avoid re-forwarding a packet in software
that was already forwarded by a hardware switch. From Scott
Feldman.
17) Allow AF_PACKET fanout function to be implemented in a bpf
program, from Willem de Bruijn"
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (1458 commits)
netfilter: nf_conntrack: make nf_ct_zone_dflt built-in
netfilter: nf_dup{4, 6}: fix build error when nf_conntrack disabled
net: fec: clear receive interrupts before processing a packet
ipv6: fix exthdrs offload registration in out_rt path
xen-netback: add support for multicast control
bgmac: Update fixed_phy_register()
sock, diag: fix panic in sock_diag_put_filterinfo
flow_dissector: Use 'const' where possible.
flow_dissector: Fix function argument ordering dependency
ixgbe: Resolve "initialized field overwritten" warnings
ixgbe: Remove bimodal SR-IOV disabling
ixgbe: Add support for reporting 2.5G link speed
ixgbe: fix bounds checking in ixgbe_setup_tc for 82598
ixgbe: support for ethtool set_rxfh
ixgbe: Avoid needless PHY access on copper phys
ixgbe: cleanup to use cached mask value
ixgbe: Remove second instance of lan_id variable
ixgbe: use kzalloc for allocating one thing
flow: Move __get_hash_from_flowi{4,6} into flow_dissector.c
ixgbe: Remove unused PCI bus types
...
Matthew R. Ochs