When a link is taken down because of a node local event, such as
disabling of a bearer or an interface, we currently leave it to the
peer node to discover the broken communication. The default time for
such failure discovery is 1.5-2 seconds.
If we instead allow the terminating link endpoint to send out a RESET
message at the moment it is reset, we can achieve the impression that
both endpoints are going down instantly. Since this is a very common
scenario, we find it worthwhile to make this small modification.
Apart from letting the link produce the said message, we also have to
ensure that the interface is able to transmit it before TIPC is
detached. We do this by performing the disabling of a bearer in three
steps:
1) Disable reception of TIPC packets from the interface in question.
2) Take down the links, while allowing them so send out a RESET message.
3) Disable transmission of TIPC packets on the interface.
Apart from this, we now have to react on the NETDEV_GOING_DOWN event,
instead of as currently the NEDEV_DOWN event, to ensure that such
transmission is possible during the teardown phase.
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Acked-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Link establishing, just like link teardown, is a non-atomic action, in
the sense that discovering that conditions are right to establish a link,
and the actual adding of the link to one of the node's send slots is done
in two different lock contexts. The link FSM is designed to help bridging
the gap between the two contexts in a safe manner.
We have now discovered a weakness in the implementaton of this FSM.
Because we directly let the link go from state LINK_ESTABLISHING to
state LINK_ESTABLISHED already in the first lock context, we are unable
to distinguish between a fully established link, i.e., a link that has
been added to its slot, and a link that has not yet reached the second
lock context. It may hence happen that a manual intervention, e.g., when
disabling an interface, causes the function tipc_node_link_down() to try
removing the link from the node slots, decrementing its active link
counter etc, although the link was never added there in the first place.
We solve this by delaying the actual state change until we reach the
second lock context, inside the function tipc_node_link_up(). This
makes it possible for potentail callers of __tipc_node_link_down() to
know if they should proceed or not, and the problem is solved.
Unforunately, the situation described above also has a second problem.
Since there by necessity is a tipc_node_link_up() call pending once
the node lock has been released, we must defuse that call by setting
the link back from LINK_ESTABLISHING to LINK_RESET state. This forces
us to make a slight modification to the link FSM, which will now look
as follows.
+------------------------------------+
|RESET_EVT |
| |
| +--------------+
| +-----------------| SYNCHING |-----------------+
| |FAILURE_EVT +--------------+ PEER_RESET_EVT|
| | A | |
| | | | |
| | | | |
| | |SYNCH_ |SYNCH_ |
| | |BEGIN_EVT |END_EVT |
| | | | |
| V | V V
| +-------------+ +--------------+ +------------+
| | RESETTING |<---------| ESTABLISHED |--------->| PEER_RESET |
| +-------------+ FAILURE_ +--------------+ PEER_ +------------+
| | EVT | A RESET_EVT |
| | | | |
| | +----------------+ | |
| RESET_EVT| |RESET_EVT | |
| | | | |
| | | |ESTABLISH_EVT |
| | | +-------------+ | |
| | | | RESET_EVT | | |
| | | | | | |
| V V V | | |
| +-------------+ +--------------+ RESET_EVT|
+--->| RESET |--------->| ESTABLISHING |<----------------+
+-------------+ PEER_ +--------------+
| A RESET_EVT |
| | |
| | |
|FAILOVER_ |FAILOVER_ |FAILOVER_
|BEGIN_EVT |END_EVT |BEGIN_EVT
| | |
V | |
+-------------+ |
| FAILINGOVER |<----------------+
+-------------+
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Acked-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
After the previous commits, we are guaranteed that no packets
of type LINK_PROTOCOL or with illegal sequence numbers will be
attempted added to the link deferred queue. This makes it possible to
make some simplifications to the sorting algorithm in the function
tipc_skb_queue_sorted().
We also alter the function so that it will drop packets if one with
the same seqeunce number is already present in the queue. This is
necessary because we have identified weird packet sequences, involving
duplicate packets, where a legitimate in-sequence packet may advance to
the head of the queue without being detected and de-queued.
Finally, we make this function outline, since it will now be called only
in exceptional cases.
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Acked-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The sequence number of an incoming packet is currently only checked
for less than, equality to, or bigger than the next expected number,
meaning that the receive window in practice becomes one half sequence
number cycle, or U16_MAX/2. This does not make sense, and may not even
be safe if there are extreme delays in the network. Any packet sent by
the peer during the ongoing cycle must belong inside his current send
window, or should otherwise be dropped if possible.
Since a link endpoint cannot know its peer's current send window, it
has to base this sanity check on a worst-case assumption, i.e., that
the peer is using a maximum sized window of 8191 packets. Using this
assumption, we now add a check that the sequence number is not bigger
than next_expected + TIPC_MAX_LINK_WIN. We also re-order the checks
done, so that the receive window test is performed before the gap test.
This way, we are guaranteed that no packet with illegal sequence numbers
are ever added to the deferred queue.
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Acked-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, all packets received in tipc_link_rcv() are unconditionally
added to the packet deferred queue, whereafter that queue is walked and
all its buffers evaluated for delivery. This is both non-optimal and
and makes the queue sorting function unnecessary complex.
This commit changes the loop so that an arrived packet is evaluated
first, and added to the deferred queue only when a sequence number gap
is discovered. A non-empty deferred queue is walked until it is empty
or until its head's sequence number doesn't fit.
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Acked-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
During packet reception, the function tipc_link_rcv() adds its accepted
packets to a temporary buffer queue, before finally splicing this queue
into the lock protected input queue that will be delivered up to the
socket layer. The purpose is to reduce potential contention on the input
queue lock. However, since the vast majority of packets arrive in
sequence, they will anyway be added one by one to the input queue, and
the use of the temporary queue becomes a sub-optimization.
The only case where this queue makes sense is when unpacking buffers
from a bundle packet; here we want to avoid dozens of small buffers
to be added individually to the lock-protected input queue in a tight
loop.
In this commit, we remove the general usage of the temporary queue,
and keep it only for the packet unbundling case.
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Acked-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
netdev_for_each_lower_dev has to be called with rtnl mutex held. So
better enforce it in switchdev functions.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since spinlock is held here, defer the switchdev operation. Also, ensure
that defered switchdev ops are processed before port master device
is unlinked.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Similar to the attr usecase, the caller knows if he is holding RTNL and is
in atomic section. So let the called to decide the correct call variant.
This allows drivers to sleep inside their ops and wait for hw to get the
operation status. Then the status is propagated into switchdev core.
This avoids silent errors in drivers.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When object is used in deferred work, we cannot use pointers in
switchdev object structures because the memory they point at may be already
used by someone else. So rather do local copy of the value.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Acked-by: Scott Feldman <sfeldma@gmail.com>
Reviewed-by: John Fastabend <john.r.fastabend@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Caller should know if he can call attr_set directly (when holding RTNL)
or if he has to defer the att_set processing for later.
This also allows drivers to sleep inside attr_set and report operation
status back to switchdev core. Switchdev core then warns if status is
not ok, instead of silent errors happening in drivers.
Benefit from newly introduced switchdev deferred ops infrastructure.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Introduce infrastructure which will be used internally to defer ops.
Note that the deferred ops are queued up and either are processed by
scheduled work or explicitly by user calling deferred_process function.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
At listen() time, there is a small window where listener is visible with
a zero backlog, triggering a spurious "Possible SYN flooding on port"
message.
Nothing prevents us from setting the correct backlog.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As we no longer hold listener lock in fast path, it is possible that a
child is created right after listener freed its bound port, if a close()
is done while incoming packets are processed.
__inet_inherit_port() must detect this and return an error,
so that caller can free the child earlier.
Fixes: e994b2f0fb ("tcp: do not lock listener to process SYN packets")
Fixes: 079096f103 ("tcp/dccp: install syn_recv requests into ehash table")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
-----BEGIN PGP SIGNATURE-----
iQEcBAABCgAGBQJWHSq8AAoJEP5prqPJtc/HCyMH/R4PeAJoSwlQQVTKxDsdC/x1
Jxue9dMpEQhINoU1EpSQxaYIwg8zzFpQqcKVzoX9bgw5YdfAVgv/wrSW98Hwg/h5
OX+QYBAvhK/1Gk0+b7fwPF323osdD/8hn4lbQorB3gEYmE4+3kKh6ivlxGNa1LfW
VDfX23MhRF+iXFM64pnl7LR6BnflPQlGEKlWQgevR+cZDfEk+lDTRHjdAu/Hjokc
Nwo1agptCOsS5mgE/hyLhqBc6UXSN8ytoi5acP+KtnfnLtmgw/YEt7/2QQgOOTkf
T2zwCxFRQcePwoip7OXFwzkPsZkj3gn4XZCbTSErbqnQ28sFDbTQUTC1mB87f70=
=0GcF
-----END PGP SIGNATURE-----
Merge tag 'linux-can-next-for-4.4-20151013' of git://git.kernel.org/pub/scm/linux/kernel/git/mkl/linux-can-next
Marc Kleine-Budde says:
====================
pull-request: can-next 2015-09-17
this is a pull request of 4 patches for net-next/master.
Two patches are by Gerhard Bertelsmann, fixing some problems in the
sun4i driver. The patch by Arnd Bergmann stops using timeval for the
CAN broadcast manager. The last patch by Alexandre Belloni removes the
otherwise unused struct at91_can_data from the driver.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Revert the commit e2ca690b65 ("ipv4/icmp: redirect messages
can use the ingress daddr as source"), which tried to introduce a more
suitable behaviour for ICMP redirect messages generated by VRRP routers.
However RFC 5798 section 8.1.1 states:
The IPv4 source address of an ICMP redirect should be the address
that the end-host used when making its next-hop routing decision.
while said commit used the generating packet destination
address, which do not match the above and in most cases leads to
no redirect packets to be generated.
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When a TCP/DCCP listener is closed, its pending SYN_RECV request sockets
become stale, meaning 3WHS can not complete.
But current behavior is wrong :
incoming packets finding such stale sockets are dropped.
We need instead to cleanup the request socket and perform another
lookup :
- Incoming ACK will give a RST answer,
- SYN rtx might find another listener if available.
- We expedite cleanup of request sockets and old listener socket.
Fixes: 079096f103 ("tcp/dccp: install syn_recv requests into ehash table")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The can subsystem communicates with user space using a bcm_msg_head
header, which contains two timestamps. This is problematic for
multiple reasons:
a) The structure layout is currently incompatible between 64-bit
user space and 32-bit user space, and cannot work in compat
mode (other than x32).
b) The timeval structure layout will change in 32-bit user
space when we fix the y2038 overflow problem by redefining
time_t to 64-bit, making new 32-bit user space incompatible
with the current kernel interface.
Cars last a long time and often use old kernels, so the actual
users of this code are the most likely ones to migrate to y2038
safe user space.
This tries to work around part of the problem by changing the
publicly visible user interface in the header, but not the binary
interface. Fortunately, the values passed around in the structure
are relative times and do not actually suffer from the y2038
overflow, so 32-bit is enough here.
We replace the use of 'struct timeval' with a newly defined
'struct bcm_timeval' that uses the exact same binary layout
as before and that still suffers from problem a) but not problem
b).
The downside of this approach is that any user space program
that currently assigns a timeval structure to these members
rather than writing the tv_sec/tv_usec portions individually
will suffer a compile-time error when built with an updated
kernel header. Fixing this error makes it work fine with old
and new headers though.
We could address problem a) by using '__u32' or 'int' members
rather than 'long', but that would have a more significant
downside in also breaking support for all existing 64-bit user
binaries that might be using this interface, which is likely
not acceptable.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Oliver Hartkopp <socketcan@hartkopp.net>
Cc: linux-can@vger.kernel.org
Cc: linux-api@vger.kernel.org
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Ido Schimmel reported a problem with switchdev devices because of the
order change of del_nbp operations, more specifically the move of
nbp_vlan_flush() which deletes all vlans and frees vlgrp after the
rx_handler has been unregistered. So in order to fix this move
vlan_flush back where it was and make it destroy the rhtable after
NULLing vlgrp and waiting a grace period to make sure noone can see it.
Reported-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As Ido Schimmel pointed out the vlan_vid_del() code in nbp_vlan_flush is
unnecessary (and is actually a remnant of the old vlan code) so we can
remove it.
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
br_fill_ifinfo is called by br_ifinfo_notify which can be called from
many contexts with different locks held, sometimes it relies upon
bridge's spinlock only which is a problem for the vlan code, so use
explicitly rcu for that to avoid problems.
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The bridge and port's vlgrp member is already used in RCU way, currently
we rely on the fact that it cannot disappear while the port exists but
that is error-prone and we might miss places with improper locking
(either RCU or RTNL must be held to walk the vlan_list). So make it
official and use RCU for vlgrp to catch offenders. Introduce proper vlgrp
accessors and use them consistently throughout the code.
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As with IPv4 support for VRFs added to IPv6 stack by replacing hardcoded
table ids with possibly device specific ones and manipulating the oif in
the flowi6. The flow flags are used to skip oif compare in nexthop lookups
if the device is enslaved to a VRF via the L3 master device.
Signed-off-by: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We shouldn't allow BRIDGE_VLAN_INFO_PVID flag in VLAN ranges.
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Acked-by: Elad Raz <eladr@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A DSA driver may not provide the port_join_bridge and port_leave_bridge
functions, so don't warn in such case.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Consider the following "duelling syn" sequence between two peers A and B:
A B
SYN1 -->
<-- SYN2
SYN2ACK -->
Note that the SYN/ACK has already been sent out by TCP before
rds_tcp_accept_one() gets invoked as part of callbacks.
If the inet_addr(A) is numerically less than inet_addr(B),
the arbitration scheme in rds_tcp_accept_one() will prefer the
TCP connection triggered by SYN1, and will send a CLOSE for the
SYN2 (just after the SYN2ACK was sent).
Since B also follows the same arbitration scheme, it will send the SYN-ACK
for SYN1 that will set up a healthy ESTABLISHED connection on both sides.
B will also get a CLOSE for SYN2, which should result in the cleanup
of the TCP state machine for SYN2, but it should not trigger any
stale RDS-TCP callbacks (such as ->writespace, ->state_change etc),
that would disrupt the progress of the SYN2 based RDS-TCP connection.
Thus the arbitration scheme in rds_tcp_accept_one() should restore
rds_tcp callbacks for the winner before setting them up for the
new accept socket, and also make sure that conn->c_outgoing
is set to 0 so that we do not trigger any reconnect attempts on the
passive side of the tcp socket in the future, in conformance with
commit c82ac7e69e ("net/rds: RDS-TCP: only initiate reconnect attempt
on outgoing TCP socket.")
Signed-off-by: Sowmini Varadhan <sowmini.varadhan@oracle.com>
Acked-by: Santosh Shilimkar <santosh.shilimkar@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The IP address passed to rds_bind() should be vetted by the
transport's ->laddr_check() for a previously bound transport.
This needs to be done to avoid cases where, for example,
the application has asked for an IB transport,
but the IP address passed to bind is only usable on
ethernet interfaces.
Signed-off-by: Sowmini Varadhan <sowmini.varadhan@oracle.com>
Acked-by: Santosh Shilimkar <santosh.shilimkar@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently it's possible for someone to send a vlan range to the kernel
with the pvid flag set which will result in the pvid bouncing from a
vlan to vlan and isn't correct, it also introduces problems for hardware
where it doesn't make sense having more than 1 pvid. iproute2 already
enforces this, so let's enforce it on kernel-side as well.
Reported-by: Elad Raz <eladr@mellanox.com>
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch makes ip6_route_info_create return err pointer instead of
returning the rt pointer by reference as suggested by Dave
Signed-off-by: Roopa Prabhu <roopa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The function nf_ct_frag6_gather is called on both the input and the
output paths of the networking stack. In particular ipv6_defrag which
calls nf_ct_frag6_gather is called from both the the PRE_ROUTING chain
on input and the LOCAL_OUT chain on output.
The addition of a net parameter makes it explicit which network
namespace the packets are being reassembled in, and removes the need
for nf_ct_frag6_gather to guess.
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Acked-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The function ip_defrag is called on both the input and the output
paths of the networking stack. In particular conntrack when it is
tracking outbound packets from the local machine calls ip_defrag.
So add a struct net parameter and stop making ip_defrag guess which
network namespace it needs to defragment packets in.
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Acked-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
ip_call_ra_chain is called early in the forwarding chain from
ip_forward and ip_mr_input, which makes skb->dev the correct
expression to get the input network device and dev_net(skb->dev) a
correct expression for the network namespace the packet is being
processed in.
Compute the network namespace and store it in a variable to make the
code clearer.
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Recent TCP listener patches exposed a prior af_packet bug :
match_fanout_group() blindly assumes it is always safe
to cast sk to a packet socket to compare fanout with af_packet_priv
But SYNACK packets can be sent while attached to request_sock, which
are smaller than a "struct sock".
We can read non existent memory and crash.
Fixes: c0de08d042 ("af_packet: don't emit packet on orig fanout group")
Fixes: ca6fb06518 ("tcp: attach SYNACK messages to request sockets instead of listener")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Willem de Bruijn <willemb@google.com>
Cc: Eric Leblond <eric@regit.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch allows configuring how the source address of ICMP
redirect messages is selected; by default the old behaviour is
retained, while setting icmp_redirects_use_orig_daddr force the
usage of the destination address of the packet that caused the
redirect.
The new behaviour fits closely the RFC 5798 section 8.1.1, and fix the
following scenario:
Two machines are set up with VRRP to act as routers out of a subnet,
they have IPs x.x.x.1/24 and x.x.x.2/24, with VRRP holding on to
x.x.x.254/24.
If a host in said subnet needs to get an ICMP redirect from the VRRP
router, i.e. to reach a destination behind a different gateway, the
source IP in the ICMP redirect is chosen as the primary IP on the
interface that the packet arrived at, i.e. x.x.x.1 or x.x.x.2.
The host will then ignore said redirect, due to RFC 1122 section 3.2.2.2,
and will continue to use the wrong next-op.
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some drivers need to implement both switchdev vlan ops and
vid_add/kill ndos. For that to work in bridge code, we need to try
switchdev op first when adding/deleting vlan id.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Acked-by: Scott Feldman <sfeldma@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
One 32bit hole is following skc_refcnt, use it.
skc_incoming_cpu can also be an union for request_sock rcv_wnd.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
SO_INCOMING_CPU as added in commit 2c8c56e15d was a getsockopt() command
to fetch incoming cpu handling a particular TCP flow after accept()
This commits adds setsockopt() support and extends SO_REUSEPORT selection
logic : If a TCP listener or UDP socket has this option set, a packet is
delivered to this socket only if CPU handling the packet matches the specified
one.
This allows to build very efficient TCP servers, using one listener per
RX queue, as the associated TCP listener should only accept flows handled
in softirq by the same cpu.
This provides optimal NUMA behavior and keep cpu caches hot.
Note that __inet_lookup_listener() still has to iterate over the list of
all listeners. Following patch puts sk_refcnt in a different cache line
to let this iteration hit only shared and read mostly cache lines.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Edward Hyunkoo Jee <edjee@google.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It's useful to allow users to set fwmark for an individual packet,
without changing the socket state. The function this patch adds in
sock layer can be used by the protocols that need such a feature.
Signed-off-by: Edward Hyunkoo Jee <edjee@google.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In order to let unprivileged users load and execute eBPF programs
teach verifier to prevent pointer leaks.
Verifier will prevent
- any arithmetic on pointers
(except R10+Imm which is used to compute stack addresses)
- comparison of pointers
(except if (map_value_ptr == 0) ... )
- passing pointers to helper functions
- indirectly passing pointers in stack to helper functions
- returning pointer from bpf program
- storing pointers into ctx or maps
Spill/fill of pointers into stack is allowed, but mangling
of pointers stored in the stack or reading them byte by byte is not.
Within bpf programs the pointers do exist, since programs need to
be able to access maps, pass skb pointer to LD_ABS insns, etc
but programs cannot pass such pointer values to the outside
or obfuscate them.
Only allow BPF_PROG_TYPE_SOCKET_FILTER unprivileged programs,
so that socket filters (tcpdump), af_packet (quic acceleration)
and future kcm can use it.
tracing and tc cls/act program types still require root permissions,
since tracing actually needs to be able to see all kernel pointers
and tc is for root only.
For example, the following unprivileged socket filter program is allowed:
int bpf_prog1(struct __sk_buff *skb)
{
u32 index = load_byte(skb, ETH_HLEN + offsetof(struct iphdr, protocol));
u64 *value = bpf_map_lookup_elem(&my_map, &index);
if (value)
*value += skb->len;
return 0;
}
but the following program is not:
int bpf_prog1(struct __sk_buff *skb)
{
u32 index = load_byte(skb, ETH_HLEN + offsetof(struct iphdr, protocol));
u64 *value = bpf_map_lookup_elem(&my_map, &index);
if (value)
*value += (u64) skb;
return 0;
}
since it would leak the kernel address into the map.
Unprivileged socket filter bpf programs have access to the
following helper functions:
- map lookup/update/delete (but they cannot store kernel pointers into them)
- get_random (it's already exposed to unprivileged user space)
- get_smp_processor_id
- tail_call into another socket filter program
- ktime_get_ns
The feature is controlled by sysctl kernel.unprivileged_bpf_disabled.
This toggle defaults to off (0), but can be set true (1). Once true,
bpf programs and maps cannot be accessed from unprivileged process,
and the toggle cannot be set back to false.
Signed-off-by: Alexei Starovoitov <ast@plumgrid.com>
Reviewed-by: Kees Cook <keescook@chromium.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use SWITCHDEV_F_SKIP_EOPNOTSUPP to skip over ports in bridge that don't
support setting ageing_time (or setting bridge attrs in general).
If push fails, don't update ageing_time in bridge and return err to user.
If push succeeds, update ageing_time in bridge and run gc_timer now to
recalabrate when to run gc_timer next, based on new ageing_time.
Signed-off-by: Scott Feldman <sfeldma@gmail.com>
Signed-off-by: Jiri Pirko <jiri@resnulli.us>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This allows us to recurse over all the ports, skipping over unsupporting
ports. Without the change, the recursion would stop at first unsupported
port.
Signed-off-by: Scott Feldman <sfeldma@gmail.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The alive parameter of tcp_orphan_retries, indicates
whether the connection is assumed alive or not.
In the function and all places calling it is used as a boolean value.
Therefore this changes the type of alive to bool in the function
definition and all calling locations.
Since tcp_orphan_tries is a tcp_timer.c local function no change in
any other file or header is necessary.
Signed-off-by: Richard Sailer <richard@weltraumpflege.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch enables adding of fdb entries pointing to the bridge device.
This can be used to propagate mac address of vlan interfaces
configured on top of the vlan filtering bridge.
Before:
$bridge fdb add 44:38:39:00:27:9f dev bridge
RTNETLINK answers: Invalid argument
After:
$bridge fdb add 44:38:39:00:27:9f dev bridge
Signed-off-by: Roopa Prabhu <roopa@cumulusnetworks.com>
Reviewed-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Before recent TCP listener patches, we were updating listener
sk->sk_rxhash before the cloning of master socket.
children sk_rxhash was therefore correct after the normal 3WHS.
But with lockless listener, we no longer dirty/change listener sk_rxhash
as it would be racy.
We need to correctly update the child sk_rxhash, otherwise first data
packet wont hit correct cpu if RFS is used.
Fixes: 079096f103 ("tcp/dccp: install syn_recv requests into ehash table")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: Willem de Bruijn <willemb@google.com>
Cc: Tom Herbert <tom@herbertland.com>
Acked-by: Tom Herbert <tom@herbertland.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For consistency with the FDB add operation, propagate the
switchdev_obj_port_fdb structure in the DSA drivers.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that the prepare phase is pushed down to the DSA drivers, propagate
it to the port_fdb_add function.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jon Paul Maloy