Not all targets have IRQ1 line routed from the SD controller to
the processor. So we cannot rely on IRQ1 for PIO interrupts.
This patch moves all PIO interrupts to IRQ0 and enables the PIO
mode.
Signed-off-by: Murali Palnati <palnatim@codeaurora.org>
Signed-off-by: Sahitya Tummala <stummala@codeaurora.org>
Signed-off-by: David Brown <davidb@codeaurora.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
On some targets, MCI_IRQ_MASK1 is not routed to the MSM in which
case only "cmd_irq" must be used even for PIO. With this change,
all the targets will use only "cmd_irq" for both CMD and PIO.
Signed-off-by: Sahitya Tummala <stummala@codeaurora.org>
Signed-off-by: David Brown <davidb@codeaurora.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
The current code checks for both DATA_END and DATA_BLK_END bits in
MCI_STATUS register and ends a request only if both are set at a time.
The hardware doesn't always set DATA_BLK_END when DATA_END is set.
But DATA_END status itself is sufficient condition from hardware that
data transfer is done and hence, check for only DATA_END interrupt in
software to end a request.
Signed-off-by: Sahitya Tummala <stummala@codeaurora.org>
Signed-off-by: David Brown <davidb@codeaurora.org>
Enable prog done interrupt for stop command(CMD12) that is sent
after a multi-block write(CMD25). The PROG_DONE bit is set when
the card has finished its programming and is ready for next data.
After every write request the card will be polled for ready status
using CMD13. For a multi-block write(CMD25) before sending CMD13,
stop command (CMD12) will be sent. If we enable prog done interrupt
for CMD12, then CMD13 polling can be avoided. The prog done interrupt
means that the card is done with its programming and is ready for
next request.
Signed-off-by: Sahitya Tummala <stummala@codeaurora.org>
Signed-off-by: David Brown <davidb@codeaurora.org>
In the context of request processing thread, data mover lock is
acquired after the host lock. In another context, in the completion
handler of data mover the locks are acquired in the reverse order,
resulting in possible circular lock dependency warning. Hence,
schedule a tasklet to process the dma completion so as to avoid
nested locks.
Signed-off-by: Sahitya Tummala <stummala@codeaurora.org>
Signed-off-by: David Brown <davidb@codeaurora.org>
CONFIG_MMC_MSM7X00A_RESUME_IN_WQ and CONFIG_MMC_EMBEDDED_SDIO don't exist
in Kconfig and is never defined anywhere else, therefore removing all
references for it from the source code.
Signed-off-by: Christian Dietrich <qy03fugy@stud.informatik.uni-erlangen.de>
Acked-by: David Brown <davidb@codeaurora.org>
Cc: Daniel Walker <dwalker@codeaurora.org>
Cc: <linux-mmc@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Rename mmc_platform_data to msm_mmc_platform_data as it is used
only by MSM platform.
Signed-off-by: Sahitya Tummala <stummala@codeaurora.org>
Signed-off-by: Daniel Walker <dwalker@codeaurora.org>
Based on an original patch by Brent DeGraaf:
"Previous versions of the SD driver were beset with excessive command
timeouts. These timeouts were silent by default, but happened
frequently, especially during heavy system activity and concurrent
access of two or more SD devices. Worst case, these timeouts would
occasionally hit at the end of a successful write, resulting in false
failures that could adversely affect journaling file systems if timing
was unfortunate. This update tightens the association and timing between
dma transfers and the commands that trigger them by utilizing a new api
implemented in the datamover. In addition, it also fixes a dma cache
coherency issue that was exposed during testing of this fix that
occasionally resulted in card corruption. Processing of results in the
interrupt status routine was modified to process command results prior to
data because overwritten command results were observed during testing
since the data section can result in command issuances of its own.
This change also eliminates the software command timeout, relying entirely
on the hardware version, since the software timeout was found to cause
problems of its own after extensive testing (having hardware timer and
software timers addressing the same issue was found to cause a race
condition under heavy system load)."
This change originally added PROG_DONE handling, which has been split out
into a separate patch. Also on our platform, the data mover driver maintains
coherency to ensure API reliability, so the above mentioned cache corruption
issue was not an issue for us.
Signed-off-by: San Mehat <san@google.com>
Cc: Brian Swetland <swetland@google.com>
Change-Id: Ifbf17cfafb858106d73bf49af52b5161a265a484
Signed-off-by: San Mehat <san@google.com>
Signed-off-by: Daniel Walker <dwalker@codeaurora.org>
- Clocks are now disabled after 1 second of inactivity
- Fixed issue which was causing us to loop through our ISR twice
- Bump core clock enable delay to 30us
Signed-off-by: San Mehat <san@google.com>
Signed-off-by: Daniel Walker <dwalker@codeaurora.org>
MMC Driver for HTC Dream. I picked the code up from Google git trees,
removed stuff not strictly necessary, and did a few cleanups. It still
works :-).
Signed-off-by: Pavel Machek <pavel@ucw.cz>
Cc: Brian Swetland <swetland@google.com>
Cc: Pierre Ossman <drzeus-list@drzeus.cx>
Cc: Joe Perches <joe@perches.com>
Cc: Matt Fleming <matt@console-pimps.org>
Cc: Ian Molton <ian@mnementh.co.uk>
Cc: "Roberto A. Foglietta" <roberto.foglietta@gmail.com>
Cc: Philip Langdale <philipl@overt.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Sahitya Tummala