The WoL feature should be disabled when config_init is called and the
feature should turned on or off when set_wol is called.
In addition updated the calls to modify the registers to use the set_bit
and clear_bit function calls.
Fixes: 6d749428788b ("net: phy: DP83TC811: Introduce support for the
DP83TC811 phy")
Signed-off-by: Dan Murphy <dmurphy@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The WoL feature should be disabled when config_init is called and the
feature should turned on or off when set_wol is called.
In addition updated the calls to modify the registers to use the set_bit
and clear_bit function calls.
Fixes: 3b427751a9d0 ("net: phy: DP83822 initial driver submission")
Signed-off-by: Dan Murphy <dmurphy@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In this code, it appears that phyter_clocks is a list head, based on
the previous list_for_each, and that clock->list is intended to be a
list element, given that it has just been initialized in
dp83640_clock_init. Accordingly, switch the arguments to
list_add_tail, which takes the list head as the second argument.
Fixes: cb646e2b02 ("ptp: Added a clock driver for the National Semiconductor PHYTER.")
Signed-off-by: Julia Lawall <Julia.Lawall@inria.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
Read the temperature sensor register from the correct location for the
88E2110 PHY. There is no enable/disable bit on 2110, so make
mv3310_hwmon_config() run on 88X3310 only.
Fixes: 62d0153547 ("net: phy: marvell10g: add support for the 88x2110 PHY")
Cc: Maxime Chevallier <maxime.chevallier@bootlin.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Reviewed-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Clear the link partner advertisement, speed, duplex and pause when
the link goes down, as other phylib drivers do. This avoids the
stale link partner, speed and duplex settings being reported via
ethtool.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
The MV_V2_PORT_CTRL_SWRST bit in MV_V2_PORT_CTRL is reserved on 88E2110.
Setting SWRST on 88E2110 breaks packets transfer after interface down/up
cycle.
Fixes: 8f48c2ac85 ("net: marvell10g: soft-reset the PHY when coming out of low power")
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Signed-off-by: David S. Miller <davem@davemloft.net>
lan87xx_phy_init() initializes the lan87xx phy hardware
including its TC10 Wake-up and Sleep features.
Fixes: 3e50d2da58 ("Add driver for Microchip LAN87XX T1 PHYs")
Signed-off-by: Yuiko Oshino <yuiko.oshino@microchip.com>
v0->v1:
- Add more details in the commit message and source comments.
- Update to the latest initialization sequences.
- Add access_ereg_modify_changed().
- Fix access_ereg() to access SMI bank correctly.
Signed-off-by: David S. Miller <davem@davemloft.net>
Soft-reset the PHY when coming out of low power mode, which seems to
be necessary with firmware versions 0.3.3.0 and 0.3.10.0.
This depends on ("net: marvell10g: report firmware version")
Fixes: c9cc1c815d ("net: phy: marvell10g: place in powersave mode at probe")
Reported-by: Matteo Croce <mcroce@redhat.com>
Tested-by: Matteo Croce <mcroce@redhat.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Report the firmware version when probing the PHY to allow issues
attributable to firmware to be diagnosed.
Tested-by: Matteo Croce <mcroce@redhat.com>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
KSZ9131 will not work with some switches due to workaround for KSZ9031
introduced in commit d2fd719bcb
("net/phy: micrel: Add workaround for bad autoneg").
Use genphy_read_status instead of dedicated ksz9031_read_status.
Fixes: bff5b4b373 ("net: phy: micrel: add Microchip KSZ9131 initial driver")
Signed-off-by: Atsushi Nemoto <atsushi.nemoto@sord.co.jp>
Signed-off-by: David S. Miller <davem@davemloft.net>
The negotiation of flow control / pause frame modes was broken since
commit fcf1f59afc ("net: phy: marvell: rearrange to use
genphy_read_lpa()") moved the setting of phydev->duplex below the
phy_resolve_aneg_pause call. Due to a check of DUPLEX_FULL in that
function, phydev->pause was no longer set.
Fix it by moving the parsing of the status variable before the blocks
dealing with the pause frames.
As the Marvell 88E1510 datasheet does not specify the timing between the
link status and the "Speed and Duplex Resolved" bit, we have to force
the link down as long as the resolved bit is not set, to avoid reporting
link up before we even have valid Speed/Duplex.
Tested with a Marvell 88E1510 (RGMII to Copper/1000Base-T)
Fixes: fcf1f59afc ("net: phy: marvell: rearrange to use genphy_read_lpa()")
Signed-off-by: Clemens Gruber <clemens.gruber@pqgruber.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Fix wrong parameter description and related warnings at 'make htmldocs'.
Signed-off-by: Lothar Rubusch <l.rubusch@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Acked-by: Randy Dunlap <rdunlap@infradead.org>
Tested-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
After the power-down bit is cleared, the chip internally triggers a
global reset. According to the KSZ9031 documentation, we have to wait at
least 1ms for the reset to finish.
If the chip is accessed during reset, read will return 0xffff, while
write will be ignored. Depending on the system performance and MDIO bus
speed, we may or may not run in to this issue.
This bug was discovered on an iMX6QP system with KSZ9031 PHY and
attached PHY interrupt line. If IRQ was used, the link status update was
lost. In polling mode, the link status update was always correct.
The investigation showed, that during a read-modify-write access, the
read returned 0xffff (while the chip was still in reset) and
corresponding write hit the chip _after_ reset and triggered (due to the
0xffff) another reset in an undocumented bit (register 0x1f, bit 1),
resulting in the next write being lost due to the new reset cycle.
This patch fixes the issue by adding a 1...2 ms sleep after the
genphy_resume().
Fixes: 836384d250 ("net: phy: micrel: Add specific suspend")
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The masks in priv->clk_25m_reg and priv->clk_25m_mask are one-bits-set
for the values that comprise the fields, not zero-bits-set.
This patch fixes the clock frequency configuration for ATH8030 and
ATH8035 Atheros PHYs by removing the erroneous "~".
To reproduce this bug, configure the PHY with the device tree binding
"qca,clk-out-frequency" and remove the machine specific PHY fixups.
Fixes: 2f664823a4 ("net: phy: at803x: add device tree binding")
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reported-by: Russell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: Russell King <rmk+kernel@armlinux.org.uk>
Tested-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a separate set of PCS operations, which MAC drivers can use to
couple phylink with their associated MAC PCS layer. The PCS
operations include:
- pcs_get_state() - reads the link up/down, resolved speed, duplex
and pause from the PCS.
- pcs_config() - configures the PCS for the specified mode, PHY
interface type, and setting the advertisement.
- pcs_an_restart() - restarts 802.3 in-band negotiation with the
link partner
- pcs_link_up() - informs the PCS that link has come up, and the
parameters of the link. Link parameters are used to program the
PCS for fixed speed and non-inband modes.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Rename the bland 'ops' member of struct phylink to be a more
descriptive 'mac_ops' - this is necessary as we're about to introduce
another set of operations.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Change phylink_mii_c22_pcs_set_advertisement() to take only the PHY
interface and advertisement mask, rather than the full phylink state.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
The PTP Hardware Clock (PHC) subsystem offers an API for configuring
programmable pins. User space sets or gets the settings using ioctls,
and drivers verify dialed settings via a callback. Drivers may also
query pin settings by calling the ptp_find_pin() method.
Although the core subsystem protects concurrent access to the pin
settings, the implementation places illogical restrictions on how
drivers may call ptp_find_pin(). When enabling an auxiliary function
via the .enable(on=1) callback, drivers may invoke the pin finding
method, but when disabling with .enable(on=0) drivers are not
permitted to do so. With the exception of the mv88e6xxx, all of the
PHC drivers do respect this restriction, but still the locking pattern
is both confusing and unnecessary.
This patch changes the locking implementation to allow PHC drivers to
freely call ptp_find_pin() from their .enable() and .verify()
callbacks.
V2 ChangeLog:
- fixed spelling in the kernel doc
- add Vladimir's tested by tag
Signed-off-by: Richard Cochran <richardcochran@gmail.com>
Reported-by: Yangbo Lu <yangbo.lu@nxp.com>
Tested-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The KSZ9131 provides DLL controlled delays on RXC and TXC lines. This
patch makes use of those delays. The information which delays should
be enabled or disabled comes from the interface names, documented in
ethernet-controller.yaml:
rgmii: Disable RXC and TXC delays
rgmii-id: Enable RXC and TXC delays
rgmii-txid: Enable only TXC delay, disable RXC delay
rgmii-rxid: Enable onlx RXC delay, disable TXC delay
Signed-off-by: Philippe Schenker <philippe.schenker@toradex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The BCM7XX PHY family requires special configuration to pass jumbo
frames. Do that during initial PHY setup.
Signed-off-by: Murali Krishna Policharla <murali.policharla@broadcom.com>
Reviewed-by: Scott Branden <scott.branden@broadcom.com>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
So far we set phydev->suspended to true in phy_suspend() even if the
PHY driver doesn't implement the suspend callback. This applies
accordingly for the resume path. The current behavior doesn't cause
any issue I'd be aware of, but it's not logical and misleading,
especially considering the description of the flag:
"suspended: Set to true if this phy has been suspended successfully"
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
An MDIO controller present on development boards for Marvell switches
from the Link Street (88E6xxx) family.
Using this module, you can use the following setup as a development
platform for switchdev and DSA related work.
.-------. .-----------------.
| USB----USB |
| SoC | | 88E6390X-DB ETH1-10
| ETH----ETH0 |
'-------' '-----------------'
Signed-off-by: Tobias Waldekranz <tobias@waldekranz.com>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If we have scenarios like
mdiobus_register()
-> loads PHY driver module(s)
-> registers PHY driver(s)
-> may schedule async probe
phydev = mdiobus_get_phy()
<phydev action involving PHY driver>
or
phydev = phy_device_create()
-> loads PHY driver module
-> registers PHY driver
-> may schedule async probe
<phydev action involving PHY driver>
then we expect the PHY driver to be bound to the phydev when triggering
the action. This may not be the case in case of asynchronous probing.
Therefore ensure that PHY drivers are probed synchronously.
Default still is sync probing, except async probing is explicitly
requested. I saw some comments that the intention is to promote
async probing for more parallelism in boot process and want to be
prepared for the case that the default is changed to async probing.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Overlapping header include additions in macsec.c
A bug fix in 'net' overlapping with the removal of 'version'
string in ena_netdev.c
Overlapping test additions in selftests Makefile
Overlapping PCI ID table adjustments in iwlwifi driver.
Signed-off-by: David S. Miller <davem@davemloft.net>
The DT binding for this PHY describes an *optional* clock property.
Due to a bug in the error handling logic, we are actually ignoring this
clock *all* of the time so far.
Fix this by using devm_clk_get_optional() to handle this clock properly.
Fixes: b78ac6ecd1 ("net: phy: mdio-bcm-unimac: Allow configuring MDIO clock divider")
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It looks like the VSC8584 PHY driver is rolling its own RGMII delay
configuration code, despite the fact that the logic is mostly the same.
In fact only the register layout and position for the RGMII controls has
changed. So we need to adapt and parameterize the PHY-dependent bit
fields when calling the new generic function.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Tested-by: Antoine Tenart <antoine.tenart@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
use readl_poll_timeout() to replace the poll codes for simplify
iproc_mdio_wait_for_idle() function
Signed-off-by: Dejin Zheng <zhengdejin5@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
use phy_read_poll_timeout() to replace the poll codes for
simplify tja11xx_check() function.
Suggested-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Dejin Zheng <zhengdejin5@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
use phy_read_poll_timeout() to replace the poll codes for
simplify lan87xx_read_status() function.
Suggested-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Dejin Zheng <zhengdejin5@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
use phy_read_poll_timeout() to replace the poll codes for
simplify the code in phy_poll_reset() function.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Dejin Zheng <zhengdejin5@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
use phy_read_mmd_poll_timeout() to replace the poll codes for
simplify mv3310_reset() function.
Suggested-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Dejin Zheng <zhengdejin5@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
use phy_read_mmd_poll_timeout() to replace the poll codes for
simplify aqr107_wait_reset_complete() function.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Dejin Zheng <zhengdejin5@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
use phy_read_mmd_poll_timeout() to replace the poll codes for
simplify bcm84881_wait_init() function.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Dejin Zheng <zhengdejin5@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that phylib notifies the user of a downshift we can remove
this functionality from the driver.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that phylib notifies the user of a downshift we can remove
this functionality from the driver.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
So far PHY drivers have to check whether a downshift occurred to be
able to notify the user. To make life of drivers authors a little bit
easier move the downshift notification to phylib. phy_check_downshift()
compares the highest mutually advertised speed with the actual value
of phydev->speed (typically read by the PHY driver from a
vendor-specific register) to detect a downshift.
v2:
- Add downshift hint to phy_print_status
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Restart AutoNeg if we didn't get a valid result from previous run.
Signed-off-by: Jose Abreu <Jose.Abreu@synopsys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Set XPCS Link as down when AutoNeg is enabled but it didn't finish with
success.
Signed-off-by: Jose Abreu <Jose.Abreu@synopsys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Reset the XPCS upon probe stage so that we start it from well known
state.
Signed-off-by: Jose Abreu <Jose.Abreu@synopsys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For 10GKR rate, when link errors are found we need to return fault
status so that XPCS is correctly resumed.
Signed-off-by: Jose Abreu <Jose.Abreu@synopsys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is a dual copper PHY with support for MII/GMII/RGMII on MAC side,
as well as a bunch of other features such as SyncE and Ring Resiliency.
I haven't tested interrupts and WoL, but I am confident that they work
since support is already present in the driver and the register map is
no different for this PHY.
PHY statistics work, PHY tunables appear to work, suspend/resume works.
Signed-off-by: Wes Li <wes.li@nxp.com>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The driver appears to be secretly enabling the RX clock skew
irrespective of PHY interface type, which is generally considered a big
no-no.
Make them configurable instead, and add TX internal delays when
necessary too.
While at it, configure a more canonical clock skew of 2.0 nanoseconds
than the current default of 1.1 ns.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The helper for configuring the pinout of the MII side of the PHY should
do so irrespective of whether RGMII delays are used or not. So accept
the ID, TXID and RXID variants as well, not just the no-delay RGMII
variant.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is nothing RX-specific about these clock skew values. So remove
"RX" from the name in preparation for the next patch where TX delays are
also going to be configured.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When the DP83867 PHY is strapped to enable Fast Link Drop (FLD) feature
STRAP_STS2.STRAP_ FLD (reg 0x006F bit 10), the Energy Lost Threshold for
FLD Energy Lost Mode FLD_THR_CFG.ENERGY_LOST_FLD_THR (reg 0x002e bits 2:0)
will be defaulted to 0x2. This may cause the phy link to be unstable. The
new DP83867 DM recommends to always restore ENERGY_LOST_FLD_THR to 0x1.
Hence, restore default value of FLD_THR_CFG.ENERGY_LOST_FLD_THR to 0x1 when
FLD is enabled by bootstrapping as recommended by DM.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds support for configuring the RGMII skew delays in Rx and
Tx. The Rx and Tx skews are set based on the interface mode. By default
their configuration is set to the default value in hardware (0.2ns);
this means the driver do not rely anymore on the bootloader
configuration.
Then based on the interface mode being used, a 2ns delay is added:
- RGMII_ID adds it for both Rx and Tx.
- RGMII_RXID adds it for Rx.
- RGMII_TXID adds it for Tx.
Signed-off-by: Antoine Tenart <antoine.tenart@bootlin.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds support for connecting VSC8584 PHYs to the MAC using
RGMII.
Signed-off-by: Antoine Tenart <antoine.tenart@bootlin.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit a5afc16780 ("net: phy: mscc: add support for VSC8584 PHY")
introduced a call to 'phy_write' storing its return value to a variable
called 'ret'. But 'ret' never was checked for a possible error being
returned, and hence was not used at all. Fix this by checking the return
value and exiting the function if an error was returned.
As this does not fix a known bug, this commit is mostly cosmetic and not
sent as a fix.
Signed-off-by: Antoine Tenart <antoine.tenart@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
At least some integrated PHY's in RTL8168/RTL8125 chip versions support
downshift, and the actual link speed can be read from a vendor-specific
register. Info about this register was provided by Realtek.
More details about downshift configuration (e.g. number of attempts)
aren't available, therefore the downshift tunable is not implemented.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The indentation for the returned values are weird, causing those
warnings:
./drivers/net/phy/sfp-bus.c:579: WARNING: Unexpected indentation.
./drivers/net/phy/sfp-bus.c:619: WARNING: Unexpected indentation.
Use a list and change the identation for it to be properly
parsed by the documentation toolchain.
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Dan Murphy