Prepare for not taking a host-wide lock in the dispatch path by pushing
the lock down into the places that actually need it. Note that this
patch is just a preparation step, as it will actually increase lock
roundtrips and thus decrease performance on its own.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Reviewed-by: Webb Scales <webbnh@hp.com>
Acked-by: Jens Axboe <axboe@kernel.dk>
Tested-by: Bart Van Assche <bvanassche@acm.org>
Tested-by: Robert Elliott <elliott@hp.com>
The blk-mq code path will set this to a different function, so make the
code simpler by setting it up in a legacy-request specific place.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Reviewed-by: Webb Scales <webbnh@hp.com>
Acked-by: Jens Axboe <axboe@kernel.dk>
Tested-by: Bart Van Assche <bvanassche@acm.org>
Tested-by: Robert Elliott <elliott@hp.com>
Make sure we only have the logic for requeing commands in one place.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Reviewed-by: Webb Scales <webbnh@hp.com>
Acked-by: Jens Axboe <axboe@kernel.dk>
Tested-by: Bart Van Assche <bvanassche@acm.org>
Tested-by: Robert Elliott <elliott@hp.com>
Factor out a helper to set the _blocked values, which we'll reuse for the
blk-mq code path.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Reviewed-by: Webb Scales <webbnh@hp.com>
Acked-by: Jens Axboe <axboe@kernel.dk>
Tested-by: Bart Van Assche <bvanassche@acm.org>
Tested-by: Robert Elliott <elliott@hp.com>
Factor out command setup code that will be shared with the blk-mq code path.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Reviewed-by: Webb Scales <webbnh@hp.com>
The data direction fiel in the SCSI command is derived only from the block
request structure. Move setting it up into common code instead of
duplicating it in the ULDs.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
We should call the device handler prep_fn for all TYPE_FS requests,
not just simple read/write calls that are handled by the disk driver.
Restructure the common I/O code to call the prep_fn handler and zero
out the CDB, and just leave the call to scsi_init_io to the ULDs.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
scsi_init_io should only be called for requests that transfer data,
so move the assert that a request has segments from the callers into
scsi_init_io.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
During IO with fabric faults, one generally sees several "Unhandled error
code" messages in the syslog as shown below:
sd 4:0:6:2: [sdbw] Unhandled error code
sd 4:0:6:2: [sdbw] Result: hostbyte=DID_NO_CONNECT driverbyte=DRIVER_OK
sd 4:0:6:2: [sdbw] CDB: Read(10): 28 00 00 00 00 00 00 00 08 00
end_request: I/O error, dev sdbw, sector 0
This comes from scsi_io_completion (in scsi_lib.c) while handling error
codes other than DID_RESET or not deferred sense keys i.e. this is
actually handled by the SCSI mid layer. But what gets displayed here is
"Unhandled error code" which is quite misleading as it indicates
something that is not addressed by the mid layer.
The description string is based on the sense key and sometimes on the
additional sense code;
since the ACTION_FAIL case always prints the sense key and the
additional sense code, this patch removes the description string
completely because it does not add useful information.
Signed-off-by: Maurizio Lombardi <mlombard@redhat.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Using dev_printk variants prefixes the logging message with
the originating device, which makes debugging easier.
Signed-off-by: Hannes Reinecke <hare@suse.de>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Flush commands don't transfer data and thus need to be special cased
in the I/O completion handler so that we can propagate errors to
the block layer and filesystem.
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Reported-by: Steven Haber <steven@qumulo.com>
Tested-by: Steven Haber <steven@qumulo.com>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Cc: stable@vger.kernel.org
Signed-off-by: Christoph Hellwig <hch@lst.de>
Pull block layer fixes from Jens Axboe:
"Final small batch of fixes to be included before -rc1. Some general
cleanups in here as well, but some of the blk-mq fixes we need for the
NVMe conversion and/or scsi-mq. The pull request contains:
- Support for not merging across a specified "chunk size", if set by
the driver. Some NVMe devices perform poorly for IO that crosses
such a chunk, so we need to support it generically as part of
request merging avoid having to do complicated split logic. From
me.
- Bump max tag depth to 10Ki tags. Some scsi devices have a huge
shared tag space. Before we failed with EINVAL if a too large tag
depth was specified, now we truncate it and pass back the actual
value. From me.
- Various blk-mq rq init fixes from me and others.
- A fix for enter on a dying queue for blk-mq from Keith. This is
needed to prevent oopsing on hot device removal.
- Fixup for blk-mq timer addition from Ming Lei.
- Small round of performance fixes for mtip32xx from Sam Bradshaw.
- Minor stack leak fix from Rickard Strandqvist.
- Two __init annotations from Fabian Frederick"
* 'for-linus' of git://git.kernel.dk/linux-block:
block: add __init to blkcg_policy_register
block: add __init to elv_register
block: ensure that bio_add_page() always accepts a page for an empty bio
blk-mq: add timer in blk_mq_start_request
blk-mq: always initialize request->start_time
block: blk-exec.c: Cleaning up local variable address returnd
mtip32xx: minor performance enhancements
blk-mq: ->timeout should be cleared in blk_mq_rq_ctx_init()
blk-mq: don't allow queue entering for a dying queue
blk-mq: bump max tag depth to 10K tags
block: add blk_rq_set_block_pc()
block: add notion of a chunk size for request merging
This patch consists of the usual driver updates (qla2xxx, qla4xxx, lpfc,
be2iscsi, fnic, ufs, NCR5380) The NCR5380 is the addition to maintained status
of a long neglected driver for older hardware. In addition there are a lot of
minor fixes and cleanups and some more updates to make scsi mq ready.
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)
iQEcBAABAgAGBQJTlcwiAAoJEDeqqVYsXL0M5qsIALzVPLd4yxA16zCiaPQUeIV5
mfYmwISFlN+qW3AcUeSH4D13YgegCjEBfqaDMWvIkgouxLy/7jpxtChutq3MCzUE
cDT1B9+ZrzoqBISRNHEh/gx5F1MOF2VPuqG2pe0J90wyRCNzJscB6PbtWMAo86CA
2eu7wq3K9FXxCC1qY0PzwBLXHqUcgk5GWiK9CM/k4W0NiTVeNmwPeh5i91IQnBHx
E2l7NAXgNLyCf5tyeswvZ4pW0T3hlaswNmBB4qC8oJm4U6UqMN+tk4ML63Pz7uPe
4mlHG0uI8Vbdi13iv1EDUZ9Vo8iqVrzP2UAhakgP9poKSGqE4d/MD0EKNGQB2Es=
=cBY8
-----END PGP SIGNATURE-----
Merge tag 'scsi-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI updates from James Bottomley:
"This patch consists of the usual driver updates (qla2xxx, qla4xxx,
lpfc, be2iscsi, fnic, ufs, NCR5380) The NCR5380 is the addition to
maintained status of a long neglected driver for older hardware. In
addition there are a lot of minor fixes and cleanups and some more
updates to make scsi mq ready"
* tag 'scsi-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi: (130 commits)
include/scsi/osd_protocol.h: remove unnecessary __constant
mvsas: Recognise device/subsystem 9485/9485 as 88SE9485
Revert "be2iscsi: Fix processing cqe for cxn whose endpoint is freed"
mptfusion: fix msgContext in mptctl_hp_hostinfo
acornscsi: remove linked command support
scsi/NCR5380: dprintk macro
fusion: Remove use of DEF_SCSI_QCMD
fusion: Add free msg frames to the head, not tail of list
mpt2sas: Add free smids to the head, not tail of list
mpt2sas: Remove use of DEF_SCSI_QCMD
mpt2sas: Remove uses of serial_number
mpt3sas: Remove use of DEF_SCSI_QCMD
mpt3sas: Remove uses of serial_number
qla2xxx: Use kmemdup instead of kmalloc + memcpy
qla4xxx: Use kmemdup instead of kmalloc + memcpy
qla2xxx: fix incorrect debug printk
be2iscsi: Bump the driver version
be2iscsi: Fix processing cqe for cxn whose endpoint is freed
be2iscsi: Fix destroy MCC-CQ before MCC-EQ is destroyed
be2iscsi: Fix memory corruption in MBX path
...
With the optimizations around not clearing the full request at alloc
time, we are leaving some of the needed init for REQ_TYPE_BLOCK_PC
up to the user allocating the request.
Add a blk_rq_set_block_pc() that sets the command type to
REQ_TYPE_BLOCK_PC, and properly initializes the members associated
with this type of request. Update callers to use this function instead
of manipulating rq->cmd_type directly.
Includes fixes from Christoph Hellwig <hch@lst.de> for my half-assed
attempt.
Signed-off-by: Jens Axboe <axboe@fb.com>
Pull block core updates from Jens Axboe:
"It's a big(ish) round this time, lots of development effort has gone
into blk-mq in the last 3 months. Generally we're heading to where
3.16 will be a feature complete and performant blk-mq. scsi-mq is
progressing nicely and will hopefully be in 3.17. A nvme port is in
progress, and the Micron pci-e flash driver, mtip32xx, is converted
and will be sent in with the driver pull request for 3.16.
This pull request contains:
- Lots of prep and support patches for scsi-mq have been integrated.
All from Christoph.
- API and code cleanups for blk-mq from Christoph.
- Lots of good corner case and error handling cleanup fixes for
blk-mq from Ming Lei.
- A flew of blk-mq updates from me:
* Provide strict mappings so that the driver can rely on the CPU
to queue mapping. This enables optimizations in the driver.
* Provided a bitmap tagging instead of percpu_ida, which never
really worked well for blk-mq. percpu_ida relies on the fact
that we have a lot more tags available than we really need, it
fails miserably for cases where we exhaust (or are close to
exhausting) the tag space.
* Provide sane support for shared tag maps, as utilized by scsi-mq
* Various fixes for IO timeouts.
* API cleanups, and lots of perf tweaks and optimizations.
- Remove 'buffer' from struct request. This is ancient code, from
when requests were always virtually mapped. Kill it, to reclaim
some space in struct request. From me.
- Remove 'magic' from blk_plug. Since we store these on the stack
and since we've never caught any actual bugs with this, lets just
get rid of it. From me.
- Only call part_in_flight() once for IO completion, as includes two
atomic reads. Hopefully we'll get a better implementation soon, as
the part IO stats are now one of the more expensive parts of doing
IO on blk-mq. From me.
- File migration of block code from {mm,fs}/ to block/. This
includes bio.c, bio-integrity.c, bounce.c, and ioprio.c. From me,
from a discussion on lkml.
That should describe the meat of the pull request. Also has various
little fixes and cleanups from Dave Jones, Shaohua Li, Duan Jiong,
Fengguang Wu, Fabian Frederick, Randy Dunlap, Robert Elliott, and Sam
Bradshaw"
* 'for-3.16/core' of git://git.kernel.dk/linux-block: (100 commits)
blk-mq: push IPI or local end_io decision to __blk_mq_complete_request()
blk-mq: remember to start timeout handler for direct queue
block: ensure that the timer is always added
blk-mq: blk_mq_unregister_hctx() can be static
blk-mq: make the sysfs mq/ layout reflect current mappings
blk-mq: blk_mq_tag_to_rq should handle flush request
block: remove dead code in scsi_ioctl:blk_verify_command
blk-mq: request initialization optimizations
block: add queue flag for disabling SG merging
block: remove 'magic' from struct blk_plug
blk-mq: remove alloc_hctx and free_hctx methods
blk-mq: add file comments and update copyright notices
blk-mq: remove blk_mq_alloc_request_pinned
blk-mq: do not use blk_mq_alloc_request_pinned in blk_mq_map_request
blk-mq: remove blk_mq_wait_for_tags
blk-mq: initialize request in __blk_mq_alloc_request
blk-mq: merge blk_mq_alloc_reserved_request into blk_mq_alloc_request
blk-mq: add helper to insert requests from irq context
blk-mq: remove stale comment for blk_mq_complete_request()
blk-mq: allow non-softirq completions
...
Instead of letting the ULD play games with the prep_fn move back to
the model of a central prep_fn with a callback to the ULD. This
already cleans up and shortens the code by itself, and will be required
to properly support blk-mq in the SCSI midlayer.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Nicholas Bellinger <nab@linux-iscsi.org>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Reviewed-by: Hannes Reinecke <hare@suse.de>
By folding scsi_end_request into its only caller we can significantly clean
up the completion logic. We can use simple goto labels now to only have
a single place to finish or requeue command there instead of the previous
convoluted logic.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Nicholas Bellinger <nab@linux-iscsi.org>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Instead of trying to guess when we have a BIDI buffer in scsi_release_buffers
add a function to explicitly free the BIDI ressoures in the one place that
handles them. This avoids needing a special __scsi_release_buffers for the
case where we already have freed the request as well.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
We're seeing a case where the contents of scmd->result isn't being reset after
a SCSI command encounters an error, is resubmitted, times out and then gets
handled. The error handler acts on the stale result of the previous error
instead of the timeout. Fix this by properly zeroing the scmd->status before
the command is resubmitted.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Patch
commit 0479633686
Author: Christoph Hellwig <hch@infradead.org>
Date: Thu Feb 20 14:20:55 2014 -0800
[SCSI] do not manipulate device reference counts in scsi_get/put_command
Introduced a use after free:I in the kill case of scsi_prep_return we have to
release our device reference, but we do this trying to reference the just
freed command. Use the local sdev pointer instead.
Fixes: 0479633686
Reported-by: Joe Lawrence <joe.lawrence@stratus.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Patch
commit 0479633686
Author: Christoph Hellwig <hch@infradead.org>
Date: Thu Feb 20 14:20:55 2014 -0800
[SCSI] do not manipulate device reference counts in scsi_get/put_command
Introduced a use after free: when scsi_init_io fails we have to release our
device reference, but we do this trying to reference the just freed command.
Add a local scsi_device pointer to fix this.
Fixes: 0479633686
Reported-by: Sander Eikelenboom <linux@eikelenboom.it>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
This was used in the olden days, back when onions were proper
yellow. Basically it mapped to the current buffer to be
transferred. With highmem being added more than a decade ago,
most drivers map pages out of a bio, and rq->buffer isn't
pointing at anything valid.
Convert old style drivers to just use bio_data().
For the discard payload use case, just reference the page
in the bio.
Signed-off-by: Jens Axboe <axboe@fb.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJTSv89AAoJEHm+PkMAQRiGd7AIAKL45dFRhX96W53uzGlpXtv7
Ecs9CMY5mtsB/rqtV/NSQaUELlNb4Ilb4lITh7NaLWAZxDJ12GwVsIbFoaBj7Ypx
tfBNNxffGGnTTn2C1PpPQmLytLBvqXIVHMaPpDvnHYJl6g9BihshLzyMrsrizqnA
DPJ0xMdgGp6BLC4qm0ZH1mS2q+TyXLN2ZCjJ1lp6NNYwBnwOe/ABjnUa0Ztu7aii
837N8h6nEuKHTr6DgrYHEgYVc3DPHPHaly/UJ8v4U30myzRv83YkD5DsBSUjSLj8
CzxJEnECa1XljLJK7SjRHy5pSP9tcUlmjx3Fk7IpQixmT+A15cov6fQ967jNlDw=
=Hxnc
-----END PGP SIGNATURE-----
Merge tag 'v3.15-rc1' into for-3.16/core
We don't like this, but things have diverged with the blk-mq fixes
in 3.15-rc1. So merge it in.
cmd_flags in struct request is now 64 bits wide but the scsi_execute
functions truncated arguments passed to int leading to errors. Make sure
the flags parameters are u64.
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Cc: Jens Axboe <axboe@fb.com>
CC: Jan Kara <jack@suse.cz>
Cc: Frederic Weisbecker <fweisbec@gmail.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
Avoid a spurious device get/put pair by cleaning up scsi_requeue_command
and folding scsi_unprep_request into it.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Eliminate a get_device() / put_device() pair from scsi_next_command().
Both are atomic operations hence removing these slightly improves
performance.
[hch: slight changes due to different context]
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
SCSI devices may only be removed by calling scsi_remove_device().
That function must invoke blk_cleanup_queue() before the final put
of sdev->sdev_gendev. Since blk_cleanup_queue() waits for the
block queue to drain and then tears it down, scsi_request_fn cannot
be active anymore after blk_cleanup_queue() has returned and hence
the get_device()/put_device() pair in scsi_request_fn is unnecessary.
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Reviewed-by: Tejun Heo <tj@kernel.org>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Many callers won't need this and we can optimize them away. In addition
the handling in the __-prefixed variants was inconsistant to start with.
Based on an earlier patch from Bart Van Assche.
[jejb: fix kerneldoc probelm picked up by Fengguang Wu]
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
If we don't have starved devices we don't need to take the host lock
to iterate over them. Also split the function up to be more clear.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Currently, scsi error handling in scsi_io_completion() tries to
unconditionally requeue scsi command when device keeps some error state.
For example, UNIT_ATTENTION causes infinite retry with
action == ACTION_RETRY.
This is because retryable errors are thought to be temporary and the scsi
device will soon recover from those errors. Normally, such retry policy is
appropriate because the device will soon recover from temporary error state.
But there is no guarantee that device is able to recover from error state
immediately. Some hardware error can prevent device from recovering.
This patch adds timeout in scsi_io_completion() to avoid infinite command
retry in scsi_io_completion(). Once scsi command retry time is longer than
this timeout, the command is treated as failure.
Signed-off-by: Eiichi Tsukata <eiichi.tsukata.xh@hitachi.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
We must use a 64-bit for this, otherwise overflowed bits get lost, and
that can result in a lower than intended value set.
Fixes: 8e0cb8a1f6 ("ARM: 7797/1: mmc: Use dma_max_pfn(dev) helper for bounce_limit calculations")
Fixes: 7d35496dd9 ("ARM: 7796/1: scsi: Use dma_max_pfn(dev) helper for bounce_limit calculations")
Tested-Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
DMA bounce limit is the maximum direct DMA'able memory beyond which
bounce buffers has to be used to perform dma operations. SCSI driver
relies on dma_mask but its calculation is based on max_*pfn which
don't have uniform meaning across architectures. So make use of
dma_max_pfn() which is expected to return the DMAable maximum pfn
value across architectures.
Cc: linux-scsi@vger.kernel.org
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Pull libata changes from Tejun Heo:
"Two interesting changes.
- libata acpi handling has been restructured so that the association
between ata devices and ACPI handles are less convoluted. This
change shouldn't change visible behavior.
- Queued TRIM support, which enables sending TRIM to the device
without draining in-flight RW commands, is added. Currently only
enabled for ahci (and likely to stay that way for the foreseeable
future).
Other changes are driver-specific updates / fixes"
* 'for-3.12' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/libata:
libata: bugfix: Remove __le32 in ata_tf_to_fis()
libata: acpi: Remove ata_dev_acpi_handle stub in libata.h
libata: Add support for queued DSM TRIM
libata: Add support for SEND/RECEIVE FPDMA QUEUED
libata: Add H2D FIS "auxiliary" port flag
libata: Populate host-to-device FIS "auxiliary" field
ata: acpi: rework the ata acpi bind support
sata, highbank: send extra clock cycles in SGPIO patterns
sata, highbank: set tx_atten override bits
devicetree: create a separate binding description for sata_highbank
drivers/ata/sata_rcar.c: simplify use of devm_ioremap_resource
sata highbank: enable 64-bit DMA mask when using LPAE
ata: pata_samsung_cf: add missing __iomem annotation
ata: pata_arasan: Staticize local symbols
sata_mv: Remove unneeded CONFIG_HAVE_CLK ifdefs
ata: use dev_get_platdata()
sata_mv: Remove unneeded forward declaration
libata: acpi: remove dead code for ata_acpi_(un)bind
libata: move 'struct ata_taskfile' and friends from ata.h to libata.h
Generate a uevent when the following Unit Attention ASC/ASCQ
codes are received:
2A/01 MODE PARAMETERS CHANGED
2A/09 CAPACITY DATA HAS CHANGED
38/07 THIN PROVISIONING SOFT THRESHOLD REACHED
3F/03 INQUIRY DATA HAS CHANGED
3F/0E REPORTED LUNS DATA HAS CHANGED
Log kernel messages when the following Unit Attention ASC/ASCQ
codes are received that are not as specific as those above:
2A/xx PARAMETERS CHANGED
3F/xx TARGET OPERATING CONDITIONS HAVE CHANGED
Added logic to set expecting_lun_change for other LUNs on the target
after REPORTED LUNS DATA HAS CHANGED is received, so that duplicate
uevents are not generated, and clear expecting_lun_change when a
REPORT LUNS command completes, in accordance with the SPC-3
specification regarding reporting of the 3F 0E ASC/ASCQ UA.
[jejb: remove SPC3 test in scsi_report_lun_change and some docbook fixes and
unused variable fix, both reported by Fengguang Wu]
Signed-off-by: Ewan D. Milne <emilne@redhat.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
When a medium error is detected the SCSI stack should return
ENODATA to the upper layers.
[jejb: fix whitespace error]
Signed-off-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
When the thin provisioning hard threshold is reached we
should return ENOSPC to inform upper layers about this fact.
Signed-off-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Document the various error codes returned on I/O failure.
Signed-off-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Binding ACPI handle to SCSI device has several drawbacks, namely:
1 During ATA device initialization time, ACPI handle will be needed
while SCSI devices are not created yet. So each time ACPI handle is
needed, instead of retrieving the handle by ACPI_HANDLE macro,
a namespace scan is performed to find the handle for the corresponding
ATA device. This is inefficient, and also expose a restriction on
calling path not holding any lock.
2 The binding to SCSI device tree makes code complex, while at the same
time doesn't bring us any benefit. All ACPI handlings are still done
in ATA module, not in SCSI.
Rework the ATA ACPI binding code to bind ACPI handle to ATA transport
devices(ATA port and ATA device). The binding needs to be done only once,
since the ATA transport devices do not go away with hotplug. And due to
this, the flush_work call in hotplug handler for ATA bay is no longer
needed.
Tested on an Intel test platform for binding and runtime power off for
ODD(ZPODD) and hard disk; on an ASUS S400C for binding and normal boot
and S3, where its SATA port node has _SDD and _GTF control methods when
configured as an AHCI controller and its PATA device node has _GTF
control method when configured as an IDE controller. SATA PMP binding
and ATA hotplug is not tested.
Signed-off-by: Aaron Lu <aaron.lu@intel.com>
Tested-by: Dirk Griesbach <spamthis@freenet.de>
Signed-off-by: Tejun Heo <tj@kernel.org>
If something goes wrong during LUN scanning, e.g. a transport layer
failure occurs, then __scsi_remove_device() can get invoked by the
LUN scanning code for a SCSI device in state SDEV_CREATED_BLOCK and
before the SCSI device has been added to sysfs (is_visible == 0).
Make sure that even in this case the transition into state SDEV_DEL
occurs. This avoids that __scsi_remove_device() can get invoked a
second time by scsi_forget_host() if this last function is invoked
from another thread than the thread that performs LUN scanning.
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
scsi_run_queue() examines all SCSI devices that are present on
the starved list. Since scsi_run_queue() unlocks the SCSI host
lock a SCSI device can get removed after it has been removed
from the starved list and before its queue is run. Protect
against that race condition by holding a reference on the
queue while running it.
Reported-by: Chanho Min <chanho.min@lge.com>
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
With the introduction of REQ_PM, modify sd's runtime suspend operation
functions to use that flag so that the operations to put the device into
runtime suspended state(i.e. sync cache and stop device) will not affect
its runtime PM status.
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Aaron Lu <aaron.lu@intel.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
USB uses the .find_bridge() callback from struct acpi_bus_type
incorrectly, because as a result of the way it is used by USB every
device in the system that doesn't have a bus type or parent is
passed to usb_acpi_find_device() for inspection.
What USB actually needs, though, is to call usb_acpi_find_device()
for USB ports that don't have a bus type defined, but have
usb_port_device_type as their device type, as well as for USB
devices.
To fix that replace the struct bus_type pointer in struct
acpi_bus_type used for matching devices to specific subsystems
with a .match() callback to be used for this purpose and update
the users of struct acpi_bus_type, including USB, accordingly.
Define the .match() callback routine for USB, usb_acpi_bus_match(),
in such a way that it will cover both USB devices and USB ports
and remove the now redundant .find_bridge() callback pointer from
usb_acpi_bus.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: Yinghai Lu <yinghai@kernel.org>
Acked-by: Jeff Garzik <jgarzik@pobox.com>
When the ODD is powered off, any action the user did to the ODD that
would generate a media event will trigger an ACPI interrupt, so the
poll for media event is no longer necessary. And the poll will also
cause a runtime status change, which will stop the ODD from staying in
powered off state, so the poll should better be stopped.
But since we don't have access to the gendisk structure in LLDs, here
comes the disk_events_disable_depth for scsi device. This field is a
hint set by LLDs to convey information to upper layer drivers. A value
of 0 means media poll is necessary for the device, while values above 0
means media poll is not needed and should better be skipped. So we can
increase its value when we are to power off the ODD in ATA layer and
decrease its value when the ODD is powered on, effectively silence the
media events poll.
Signed-off-by: Aaron Lu <aaron.lu@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Pull block layer core updates from Jens Axboe:
"Here are the core block IO bits for 3.8. The branch contains:
- The final version of the surprise device removal fixups from Bart.
- Don't hide EFI partitions under advanced partition types. It's
fairly wide spread these days. This is especially dangerous for
systems that have both msdos and efi partition tables, where you
want to keep them in sync.
- Cleanup of using -1 instead of the proper NUMA_NO_NODE
- Export control of bdi flusher thread CPU mask and default to using
the home node (if known) from Jeff.
- Export unplug tracepoint for MD.
- Core improvements from Shaohua. Reinstate the recursive merge, as
the original bug has been fixed. Add plugging for discard and also
fix a problem handling non pow-of-2 discard limits.
There's a trivial merge in block/blk-exec.c due to a fix that went
into 3.7-rc at a later point than -rc4 where this is based."
* 'for-3.8/core' of git://git.kernel.dk/linux-block:
block: export block_unplug tracepoint
block: add plug for blkdev_issue_discard
block: discard granularity might not be power of 2
deadline: Allow 0ms deadline latency, increase the read speed
partitions: enable EFI/GPT support by default
bsg: Remove unused function bsg_goose_queue()
block: Make blk_cleanup_queue() wait until request_fn finished
block: Avoid scheduling delayed work on a dead queue
block: Avoid that request_fn is invoked on a dead queue
block: Let blk_drain_queue() caller obtain the queue lock
block: Rename queue dead flag
bdi: add a user-tunable cpu_list for the bdi flusher threads
block: use NUMA_NO_NODE instead of -1
block: recursive merge requests
block CFQ: avoid moving request to different queue
QUEUE_FLAG_DEAD is used to indicate that queuing new requests must
stop. After this flag has been set queue draining starts. However,
during the queue draining phase it is still safe to invoke the
queue's request_fn, so QUEUE_FLAG_DYING is a better name for this
flag.
This patch has been generated by running the following command
over the kernel source tree:
git grep -lEw 'blk_queue_dead|QUEUE_FLAG_DEAD' |
xargs sed -i.tmp -e 's/blk_queue_dead/blk_queue_dying/g' \
-e 's/QUEUE_FLAG_DEAD/QUEUE_FLAG_DYING/g'; \
sed -i.tmp -e "s/QUEUE_FLAG_DYING$(printf \\t)*5/QUEUE_FLAG_DYING$(printf \\t)5/g" \
include/linux/blkdev.h; \
sed -i.tmp -e 's/ DEAD/ DYING/g' -e 's/dead queue/a dying queue/' \
-e 's/Dead queue/A dying queue/' block/blk-core.c
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Acked-by: Tejun Heo <tj@kernel.org>
Cc: James Bottomley <JBottomley@Parallels.com>
Cc: Mike Christie <michaelc@cs.wisc.edu>
Cc: Jens Axboe <axboe@kernel.dk>
Cc: Chanho Min <chanho.min@lge.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Implement support for WRITE SAME(10) and WRITE SAME(16) in the SCSI disk
driver.
- We set the default maximum to 0xFFFF because there are several
devices out there that only support two-byte block counts even with
WRITE SAME(16). We only enable transfers bigger than 0xFFFF if the
device explicitly reports MAXIMUM WRITE SAME LENGTH in the BLOCK
LIMITS VPD.
- max_write_same_blocks can be overriden per-device basis in sysfs.
- The UNMAP discovery heuristics remain unchanged but the discard
limits are tweaked to match the "real" WRITE SAME commands.
- In the error handling logic we now distinguish between WRITE SAME
with and without UNMAP set.
The discovery process heuristics are:
- If the device reports a SCSI level of SPC-3 or greater we'll issue
READ SUPPORTED OPERATION CODES to find out whether WRITE SAME(16) is
supported. If that's the case we will use it.
- If the device supports the block limits VPD and reports a MAXIMUM
WRITE SAME LENGTH bigger than 0xFFFF we will use WRITE SAME(16).
- Otherwise we will use WRITE SAME(10) unless the target LBA is beyond
0xFFFFFFFF or the block count exceeds 0xFFFF.
- no_write_same is set for ATA, FireWire and USB.
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Reviewed-by: Mike Snitzer <snitzer@redhat.com>
Reviewed-by: Jeff Garzik <jgarzik@redhat.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
FC and iSCSI class set SCSI devices to transport-offline state after
fast_io_fail/replacement_timeout has fired, but after relogin, function
scsi_internal_device_unblock() is not setting scsi device state to running.
Due to this the devices even after being relogged in remain offline.
Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Two bits were appended to the end of the bitfield
list in struct scsi_device. Resolve that conflict
by including both bits.
Conflicts:
include/scsi/scsi_device.h
Avoid that the code for requeueing SCSI requests triggers a
crash by making sure that that code isn't scheduled anymore
after a device has been removed.
Also, source code inspection of __scsi_remove_device() revealed
a race condition in this function: no new SCSI requests must be
accepted for a SCSI device after device removal started.
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Acked-by: Tejun Heo <tj@kernel.org>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
The return value of scsi_queue_insert() is ignored by all its
callers, hence change the return type of this function into
void.
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Reviewed-by: Tejun Heo <tj@kernel.org>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
When we call scsi_unprep_request() the command associated with the request
gets destroyed and therefore drops its reference on the device. If this was
the only reference, the device may get released and we end up with a NULL
pointer deref when we call blk_requeue_request.
Reported-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Reviewed-by: Tejun Heo <tj@kernel.org>
Cc: <stable@kernel.org>
[jejb: enhance commend and add commit log for stable]
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Use blk_queue_dead() to test whether the queue is dead instead
of !sdev. Since scsi_prep_fn() may be invoked concurrently with
__scsi_remove_device(), keep the queuedata (sdev) pointer in
__scsi_remove_device(). This patch fixes a kernel oops that
can be triggered by USB device removal. See also
http://www.spinics.net/lists/linux-scsi/msg56254.html.
Other changes included in this patch:
- Swap the blk_cleanup_queue() and kfree() calls in
scsi_host_dev_release() to make that code easier to grasp.
- Remove the queue dead check from scsi_run_queue() since the
queue state can change anyway at any point in that function
where the queue lock is not held.
- Remove the queue dead check from the start of scsi_request_fn()
since it is redundant with the scsi_device_online() check.
Reported-by: Jun'ichi Nomura <j-nomura@ce.jp.nec.com>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Reviewed-by: Tejun Heo <tj@kernel.org>
Cc: <stable@kernel.org>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
We do not hold the host lock when calling these functions,
so remove comment.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
This has scsi_internal_device_unblock/scsi_target_unblock take
the new state to set the devices as an argument instead of
always setting to running. The patch also converts users of these
functions.
This allows the FC and iSCSI class to transition devices from blocked
to transport-offline, so that when fast_io_fail/replacement_timeout
has fired we do not set the devices back to running. Instead, we
set them to SDEV_TRANSPORT_OFFLINE.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
This patch adds a new state SDEV_TRANSPORT_OFFLINE. It will
be used by transport classes to offline devices for cases like
when the fast_io_fail/recovery_tmo fires. In those cases we
want all IO to fail, and we have not yet escalated to dev_loss_tmo
behavior where we are removing the devices.
Currently to handle this state, transport classes are setting
the scsi_device's state to running, setting their internal
session/port structs state to something that indicates failed,
and then failing IO from some transport check in the queuecommand.
The reason for the new value is so that users can distinguish
between a device failure that is a result of a transport problem
vs the wide range of errors that devices get offlined for
when a scsi command times out and we offline the devices there.
It also fixes the confusion as to why the transport class is
failing IO, but has set the device state from blocked to running.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
For being able to bind ata devices against acpi devices, scsi_bus_type
needs to be set as bus in struct acpi_bus_type. So add wrapper to
scsi_lib to accomplish that.
Signed-off-by: Holger Macht <holger@homac.de>
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
block congestion control doesn't have any concept of fairness across
multiple queues. This means that if SCSI reports the host as busy in
the queue congestion control it can result in an unfair starvation
situation in dm-mp if there are multiple multipath devices on the same
host. For example:
http://www.redhat.com/archives/dm-devel/2012-May/msg00123.html
The fix for this is to report only the sdev busy state (and ignore the
host busy state) in the block congestion control call back.
The host is still congested, but the SCSI subsystem will sort out the
congestion in a fair way because it knows the relation between the
queues and the host.
[jejb: fixed up trailing whitespace]
Reported-by: Bernd Schubert <bernd.schubert@itwm.fraunhofer.de>
Tested-by: Bernd Schubert <bernd.schubert@itwm.fraunhofer.de>
Signed-off-by: Jun'ichi Nomura <j-nomura@ce.jp.nec.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
1/ Rework remote-node-context (RNC) handling for proper management of
the silicon state machine in error handling and hot-plug conditions.
Further details below, suffice to say if the RNC is mismanaged the
silicon state machines may lock up.
2/ Refactor the initialization code to be reused for suspend/resume support
3/ Miscellaneous bug fixes to address discovery issues and hardware
compatibility.
RNC rework details from Jeff Skirvin:
In the controller, devices as they appear on a SAS domain (or
direct-attached SATA devices) are represented by memory structures known
as "Remote Node Contexts" (RNCs). These structures are transferred from
main memory to the controller using a set of register commands; these
commands include setting up the context ("posting"), removing the
context ("invalidating"), and commands to control the scheduling of
commands and connections to that remote device ("suspensions" and
"resumptions"). There is a similar path to control RNC scheduling from
the protocol engine, which interprets the results of command and data
transmission and reception.
In general, the controller chooses among non-suspended RNCs to find one
that has work requiring scheduling the transmission of command and data
frames to a target. Likewise, when a target tries to return data back
to the initiator, the state of the RNC is used by the controller to
determine how to treat the incoming request. As an example, if the RNC
is in the state "TX/RX Suspended", incoming SSP connection requests from
the target will be rejected by the controller hardware. When an RNC is
"TX Suspended", it will not be selected by the controller hardware to
start outgoing command or data operations (with certain priority-based
exceptions).
As mentioned above, there are two sources for management of the RNC
states: commands from driver software, and the result of transmission
and reception conditions of commands and data signaled by the controller
hardware. As an example of the latter, if an outgoing SSP command ends
with a OPEN_REJECT(BAD_DESTINATION) status, the RNC state will
transition to the "TX Suspended" state, and this is signaled by the
controller hardware in the status to the completion of the pending
command as well as signaled in a controller hardware event. Examples of
the former are included in the patch changelogs.
Driver software is required to suspend the RNC in a "TX/RX Suspended"
condition before any outstanding commands can be terminated. Failure to
guarantee this can lead to a complete hardware hang condition. Earlier
versions of the driver software did not guarantee that an RNC was
correctly managed before I/O termination, and so operated in an unsafe
way.
Further, the driver performed unnecessary contortions to preserve the
remote device command state and so was more complicated than it needed
to be. A simplifying driver assumption is that once an I/O has entered
the error handler path without having completed in the target, the
requirement on the driver is that all use of the sas_task must end.
Beyond that, recovery of operation is dependent on libsas and other
components to reset, rediscover and reconfigure the device before normal
operation can restart. In the driver, this simplifying assumption meant
that the RNC management could be reduced to entry into the suspended
state, terminating the targeted I/O request, and resuming the RNC as
needed for device-specific management such as an SSP Abort Task or LUN
Reset Management request.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)
iQIcBAABAgAGBQJPtYFXAAoJEB7SkWpmfYgCJkcP/1VvsuuitNy/YM9P1tb/RvQ7
ytJzjGtWiAABHVWwjgB+Ng7hUTaP2r6l8KeNfwxpwXyNdBAUNysYEUBHAfPsKzKz
espTmw3wVCnREajgKXZwFp9aTj8DcYFB6vKcC/ddACt3uRNjjA9En36+6797r8Vg
YdebyjFX2FxwoUj0icTUiV/OXgb8w723imnCl8bfOhhFRi4eFZ4EJ23AdMkUya1i
uYePAPJPSQJuU/87gNIx4JcR0qHJ1ziGPEY+XC47CzEeXbBTSPgWOwanQ6KPoXRJ
XVxamfcKAjRdtwQ4m1vYBSE32RTdrjhujVbkGiPi6QaEbCLjhLSCIYyuS3XMckV+
TCZ16o5kd/I6ZtZOeP4zZRGnNBkOPzY44qiJeKffjWDhTrFacx4XWJB/ftWPgEA5
N2zFH3RM4sY0FUJ3I/Qe5CERNdCXMtcj+UAf3nHpAIVcv46Lp+qoSkdEx05uuuiN
+D/dSlubktuvuzmB5WisL3qrjNEkkLTAGQpZs1j0ojLEBm0XAgV5EzqmHiZ0GOPD
OQNFxeei9SlqgtKIIP0bymRispPrG2HVCOvExYMxzKR6fjxofZLAs/aWOsdhxgMq
TlAyZJ6OmGI+KX68HHzoMpT9iquvmP64WGkfHzCx296BfSKiruLh/Jzt5gGwv+Z1
5tlpnUr9dUTxx7qkQXvj
=HYvO
-----END PGP SIGNATURE-----
Merge tag 'isci-for-3.5' into misc
isci update for 3.5
1/ Rework remote-node-context (RNC) handling for proper management of
the silicon state machine in error handling and hot-plug conditions.
Further details below, suffice to say if the RNC is mismanaged the
silicon state machines may lock up.
2/ Refactor the initialization code to be reused for suspend/resume support
3/ Miscellaneous bug fixes to address discovery issues and hardware
compatibility.
RNC rework details from Jeff Skirvin:
In the controller, devices as they appear on a SAS domain (or
direct-attached SATA devices) are represented by memory structures known
as "Remote Node Contexts" (RNCs). These structures are transferred from
main memory to the controller using a set of register commands; these
commands include setting up the context ("posting"), removing the
context ("invalidating"), and commands to control the scheduling of
commands and connections to that remote device ("suspensions" and
"resumptions"). There is a similar path to control RNC scheduling from
the protocol engine, which interprets the results of command and data
transmission and reception.
In general, the controller chooses among non-suspended RNCs to find one
that has work requiring scheduling the transmission of command and data
frames to a target. Likewise, when a target tries to return data back
to the initiator, the state of the RNC is used by the controller to
determine how to treat the incoming request. As an example, if the RNC
is in the state "TX/RX Suspended", incoming SSP connection requests from
the target will be rejected by the controller hardware. When an RNC is
"TX Suspended", it will not be selected by the controller hardware to
start outgoing command or data operations (with certain priority-based
exceptions).
As mentioned above, there are two sources for management of the RNC
states: commands from driver software, and the result of transmission
and reception conditions of commands and data signaled by the controller
hardware. As an example of the latter, if an outgoing SSP command ends
with a OPEN_REJECT(BAD_DESTINATION) status, the RNC state will
transition to the "TX Suspended" state, and this is signaled by the
controller hardware in the status to the completion of the pending
command as well as signaled in a controller hardware event. Examples of
the former are included in the patch changelogs.
Driver software is required to suspend the RNC in a "TX/RX Suspended"
condition before any outstanding commands can be terminated. Failure to
guarantee this can lead to a complete hardware hang condition. Earlier
versions of the driver software did not guarantee that an RNC was
correctly managed before I/O termination, and so operated in an unsafe
way.
Further, the driver performed unnecessary contortions to preserve the
remote device command state and so was more complicated than it needed
to be. A simplifying driver assumption is that once an I/O has entered
the error handler path without having completed in the target, the
requirement on the driver is that all use of the sas_task must end.
Beyond that, recovery of operation is dependent on libsas and other
components to reset, rediscover and reconfigure the device before normal
operation can restart. In the driver, this simplifying assumption meant
that the RNC management could be reduced to entry into the suspended
state, terminating the targeted I/O request, and resuming the RNC as
needed for device-specific management such as an SSP Abort Task or LUN
Reset Management request.
Currently, __scsi_alloc_queue uses SCSI host's parent device
as DMA device to set segment boundary. But the parent device may not
refer to the DMA device. For example, for ATA disk, SCSI host's parent
device now refers to ATA port.
Since commit d139b9b([SCSI] scsi_lib_dma: fix bug with dma maps on
nested scsi objects), a new field Scsi_Host->dma_dev was introduced
to refer to the real DMA device.
Use ->dma_dev in __scsi_alloc_queue to correctly set segment
boundary.
Bug report: http://marc.info/?l=linux-ide&m=133177818318187&w=2
Reported-and-tested-by: Jörg Sommer <joerg@alea.gnuu.de>
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.18 (GNU/Linux)
iQEcBAABAgAGBQJPZxSnAAoJEDeqqVYsXL0M0Y4IAMX0vrTVZbg6psA5/gMcWGRP
CkFXEQ8n0PL2SCaj6BoDqamJFe5Nc7dnqxM0fGawB4S9vr3rHhiOlwO+NbV9zFYC
2skBTpeL3sjgtN/jTBdfeeAa7xTYpu/XGyei0NS1A5c2AyMVXV0uYV2s4VNZxe44
tVIn1OEzM2giZ9EB1OZslDMrg5XXm3MBIUECP0LbWUhBm/35caSFKzMXRwhh7WiK
+AVmc2AZYtdEwuknDyiH7KlsaoB3vGL9pPrAUJzIgEhy2pOo2A7W72HfA4Fj+y6a
uF9HBS5zciMp1+sGWry62AjNbWgin9BRlozBEO/lJhIfMGDV1nXEIJsOkOgkdoE=
=1TxB
-----END PGP SIGNATURE-----
Merge tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi-misc-2.6
SCSI updates from James Bottomley:
"The update includes the usual assortment of driver updates (lpfc,
qla2xxx, qla4xxx, bfa, bnx2fc, bnx2i, isci, fcoe, hpsa) plus a huge
amount of infrastructure work in the SAS library and transport class
as well as an iSCSI update. There's also a new SCSI based virtio
driver."
* tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi-misc-2.6: (177 commits)
[SCSI] qla4xxx: Update driver version to 5.02.00-k15
[SCSI] qla4xxx: trivial cleanup
[SCSI] qla4xxx: Fix sparse warning
[SCSI] qla4xxx: Add support for multiple session per host.
[SCSI] qla4xxx: Export CHAP index as sysfs attribute
[SCSI] scsi_transport: Export CHAP index as sysfs attribute
[SCSI] qla4xxx: Add support to display CHAP list and delete CHAP entry
[SCSI] iscsi_transport: Add support to display CHAP list and delete CHAP entry
[SCSI] pm8001: fix endian issue with code optimization.
[SCSI] pm8001: Fix possible racing condition.
[SCSI] pm8001: Fix bogus interrupt state flag issue.
[SCSI] ipr: update PCI ID definitions for new adapters
[SCSI] qla2xxx: handle default case in qla2x00_request_firmware()
[SCSI] isci: improvements in driver unloading routine
[SCSI] isci: improve phy event warnings
[SCSI] isci: debug, provide state-enum-to-string conversions
[SCSI] scsi_transport_sas: 'enable' phys on reset
[SCSI] libsas: don't recover end devices attached to disabled phys
[SCSI] libsas: fixup target_port_protocols for expanders that don't report sata
[SCSI] libsas: set attached device type and target protocols for local phys
...
The error reported up the stack for a discard failure did not clearly
indicate that the command was processed and subsequently failed by the
target device.
Return -EREMOTEIO so multipathing does not classify this condition as a
path failure.
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Acked-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
This patch fixes the host byte settings DID_TARGET_FAILURE and
DID_NEXUS_FAILURE. The function __scsi_error_from_host_byte, tries to reset
the host byte to DID_OK. But that does not happen because of the OR operation.
Here is the flow.
scsi_softirq_done-> scsi_decide_disposition -> __scsi_error_from_host_byte
Let's take an example with DID_NEXUS_FAILURE. In scsi_decide_disposition,
result will be set as DID_NEXUS_FAILURE (=0x11). Then in
__scsi_error_from_host_byte, when we do OR with DID_OK. Purpose is to reset
it back to DID_OK. But that does not happen. This patch fixes this issue.
Signed-off-by: Babu Moger <babu.moger@netapp.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
The sdev is deleted from starved list and then try to dispatch from this
device. It's quite possible the sdev can't eventually dispatch a request,
then the sdev will be in starved list tail. This isn't fair.
There are two cases here:
1. unplug path. scsi_request_fn() calls to scsi_target_queue_ready(), then
the dev is removed from starved list, but quite possible host queue isn't
ready, the dev is moved to starved list without dispatching any request.
2. scsi_run_queue path. It deletes the dev from starved list first (both
global and local starved lists), then handles the dev. Then we could have
the same process like case 1.
This patch fixes the first case. Case 2 isn't fixed, because there is a
rare case scsi_run_queue finds host isn't busy but scsi_request_fn finds
host is busy (other CPU is faster to get host queue depth). Not deleting
the dev from starved list in scsi_run_queue will keep scsi_run_queue
looping (though this is very rare case, because host will become busy).
Fortunately fixing case 1 already gives big improvement for starvation in
my test. In a 12 disk JBOD setup, running file creation under EXT4, this
gives 12% more throughput.
Signed-off-by: Shaohua Li <shaohua.li@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
When we tear down a device we try to flush all outstanding
commands in scsi_free_queue(). However the check in
scsi_request_fn() is imperfect as it only signals that
we _might start_ aborting commands, not that we've actually
aborted some.
So move the printk inside the scsi_kill_request function,
this will also give us a hint about which commands are aborted.
Signed-off-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
* 'modsplit-Oct31_2011' of git://git.kernel.org/pub/scm/linux/kernel/git/paulg/linux: (230 commits)
Revert "tracing: Include module.h in define_trace.h"
irq: don't put module.h into irq.h for tracking irqgen modules.
bluetooth: macroize two small inlines to avoid module.h
ip_vs.h: fix implicit use of module_get/module_put from module.h
nf_conntrack.h: fix up fallout from implicit moduleparam.h presence
include: replace linux/module.h with "struct module" wherever possible
include: convert various register fcns to macros to avoid include chaining
crypto.h: remove unused crypto_tfm_alg_modname() inline
uwb.h: fix implicit use of asm/page.h for PAGE_SIZE
pm_runtime.h: explicitly requires notifier.h
linux/dmaengine.h: fix implicit use of bitmap.h and asm/page.h
miscdevice.h: fix up implicit use of lists and types
stop_machine.h: fix implicit use of smp.h for smp_processor_id
of: fix implicit use of errno.h in include/linux/of.h
of_platform.h: delete needless include <linux/module.h>
acpi: remove module.h include from platform/aclinux.h
miscdevice.h: delete unnecessary inclusion of module.h
device_cgroup.h: delete needless include <linux/module.h>
net: sch_generic remove redundant use of <linux/module.h>
net: inet_timewait_sock doesnt need <linux/module.h>
...
Fix up trivial conflicts (other header files, and removal of the ab3550 mfd driver) in
- drivers/media/dvb/frontends/dibx000_common.c
- drivers/media/video/{mt9m111.c,ov6650.c}
- drivers/mfd/ab3550-core.c
- include/linux/dmaengine.h
For the basic SCSI infrastructure files that are exporting symbols
but not modules themselves, add in the basic export.h header file
to allow the exports.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Make sure that SCSI device removal via scsi_remove_host() does finish
all pending SCSI commands. Currently that's not the case and hence
removal of a SCSI host during I/O can cause a deadlock. See also
"blkdev_issue_discard() hangs forever if underlying storage device is
removed" (http://bugzilla.kernel.org/show_bug.cgi?id=40472). See also
http://lkml.org/lkml/2011/8/27/6.
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Cc: <stable@kernel.org>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
During cable pull tests on our 16G FC adapter, we are seeing errors,
typically reads to close targets, which fail due to CRC or framing
errors caused by the cable being pull (return status DID_ERROR).
The adapter detects the error on one of the first frames received,
marks the FC exchange as dead (further frames go to bit bucket) and
signals the host of the error. This action is so quick, and coupled
with fast host CPUs, creates a scenario in which the midlayer sees
the failure and retries the io almost immediately. We've seen link
traces with the retry on the link while the original i/o is still
being processed by the target. We're also seeing the time window
for the "link to pull-apart" and the physical interface to report
disconnected to be in the few millisecond range. Which means, we're
encountering scenarios where the full retry count is exhausted
(all with error) by the midlayer before the link disconnect state
is detected.
We looked at 8G FC behavior and occasionally see the same behavior,
but as the link was slower, it rarely could exhaust all retries
before the link reported disconnect.
What is needed is a slight delay between io retries due to DID_ERROR
to cover this error. It is inappropriate to put this delay in the
driver, as the error is indistinguishable from other link-related errors,
nor does the driver track whether the io is a retry or not. This is also
easier than tracking between-io-error bursts that are seen in this
scenario.
The patch below updates the retry path so that it inserts a delay as
if the target was busy. The busy delay is on the order of 6ms. This
delay is sufficient to ensure the link down condition is reported
before the retry count is exhausted (at most 1 retry is seen).
Signed-off-by: Alex Iannicelli <alex.iannicelli@emulex.com>
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
USB surprise removal of sr is triggering an oops in
scsi_dispatch_command(). What seems to be happening is that USB is
hanging on to a queue reference until the last close of the upper
device, so the crash is caused by surprise remove of a mounted CD
followed by attempted unmount.
The problem is that USB doesn't issue its final commands as part of
the SCSI teardown path, but on last close when the block queue is long
gone. The long term fix is probably to make sr do the teardown in the
same way as sd (so remove all the lower bits on ejection, but keep the
upper disk alive until last close of user space). However, the
current oops can be simply fixed by not allowing any commands to be
sent to a dead queue.
Cc: stable@kernel.org
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
* 'for-linus' of git://git.kernel.dk/linux-2.6-block:
block: don't delay blk_run_queue_async
scsi: remove performance regression due to async queue run
blk-throttle: Use task_subsys_state() to determine a task's blkio_cgroup
block: rescan partitions on invalidated devices on -ENOMEDIA too
cdrom: always check_disk_change() on open
block: unexport DISK_EVENT_MEDIA_CHANGE for legacy/fringe drivers
Commit c21e6beb removed our queue request_fn re-enter
protection, and defaulted to always running the queues from
kblockd to be safe. This was a known potential slow down,
but should be safe.
Unfortunately this is causing big performance regressions for
some, so we need to improve this logic. Looking into the details
of the re-enter, the real issue is on requeue of requests.
Requeue of requests upon seeing a BUSY condition from the device
ends up re-running the queue, causing traces like this:
scsi_request_fn()
scsi_dispatch_cmd()
scsi_queue_insert()
__scsi_queue_insert()
scsi_run_queue()
scsi_request_fn()
...
potentially causing the issue we want to avoid. So special
case the requeue re-run of the queue, but improve it to offload
the entire run of local queue and starved queue from a single
workqueue callback. This is a lot better than potentially
kicking off a workqueue run for each device seen.
This also fixes the issue of the local device going into recursion,
since the above mentioned commit never moved that queue run out
of line.
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
The recent commit closing the race window in device teardown:
commit 86cbfb5607
Author: James Bottomley <James.Bottomley@suse.de>
Date: Fri Apr 22 10:39:59 2011 -0500
[SCSI] put stricter guards on queue dead checks
is causing a potential NULL deref in scsi_run_queue() because the
q->queuedata may already be NULL by the time this function is called.
Since we shouldn't be running a queue that is being torn down, simply
add a NULL check in scsi_run_queue() to forestall this.
Tested-by: Jim Schutt <jaschut@sandia.gov>
Cc: stable@kernel.org
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
We are currently using this flag to check whether it's safe
to call into ->request_fn(). If it is set, we punt to kblockd.
But we get a lot of false positives and excessive punts to
kblockd, which hurts performance.
The only real abuser of this infrastructure is SCSI. So export
the async queue run and convert SCSI over to use that. There's
room for improvement in that SCSI need not always use the async
call, but this fixes our performance issue and they can fix that
up in due time.
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
Instead of overloading __blk_run_queue to force an offload to kblockd
add a new blk_run_queue_async helper to do it explicitly. I've kept
the blk_queue_stopped check for now, but I suspect it's not needed
as the check we do when the workqueue items runs should be enough.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
* 'for-2.6.39/core' of git://git.kernel.dk/linux-2.6-block: (65 commits)
Documentation/iostats.txt: bit-size reference etc.
cfq-iosched: removing unnecessary think time checking
cfq-iosched: Don't clear queue stats when preempt.
blk-throttle: Reset group slice when limits are changed
blk-cgroup: Only give unaccounted_time under debug
cfq-iosched: Don't set active queue in preempt
block: fix non-atomic access to genhd inflight structures
block: attempt to merge with existing requests on plug flush
block: NULL dereference on error path in __blkdev_get()
cfq-iosched: Don't update group weights when on service tree
fs: assign sb->s_bdi to default_backing_dev_info if the bdi is going away
block: Require subsystems to explicitly allocate bio_set integrity mempool
jbd2: finish conversion from WRITE_SYNC_PLUG to WRITE_SYNC and explicit plugging
jbd: finish conversion from WRITE_SYNC_PLUG to WRITE_SYNC and explicit plugging
fs: make fsync_buffers_list() plug
mm: make generic_writepages() use plugging
blk-cgroup: Add unaccounted time to timeslice_used.
block: fixup plugging stubs for !CONFIG_BLOCK
block: remove obsolete comments for blkdev_issue_zeroout.
blktrace: Use rq->cmd_flags directly in blk_add_trace_rq.
...
Fix up conflicts in fs/{aio.c,super.c}
* git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi-misc-2.6: (170 commits)
[SCSI] scsi_dh_rdac: Add MD36xxf into device list
[SCSI] scsi_debug: add consecutive medium errors
[SCSI] libsas: fix ata list corruption issue
[SCSI] hpsa: export resettable host attribute
[SCSI] hpsa: move device attributes to avoid forward declarations
[SCSI] scsi_debug: Logical Block Provisioning (SBC3r26)
[SCSI] sd: Logical Block Provisioning update
[SCSI] Include protection operation in SCSI command trace
[SCSI] hpsa: fix incorrect PCI IDs and add two new ones (2nd try)
[SCSI] target: Fix volume size misreporting for volumes > 2TB
[SCSI] bnx2fc: Broadcom FCoE offload driver
[SCSI] fcoe: fix broken fcoe interface reset
[SCSI] fcoe: precedence bug in fcoe_filter_frames()
[SCSI] libfcoe: Remove stale fcoe-netdev entries
[SCSI] libfcoe: Move FCOE_MTU definition from fcoe.h to libfcoe.h
[SCSI] libfc: introduce __fc_fill_fc_hdr that accepts fc_hdr as an argument
[SCSI] fcoe, libfc: initialize EM anchors list and then update npiv EMs
[SCSI] Revert "[SCSI] libfc: fix exchange being deleted when the abort itself is timed out"
[SCSI] libfc: Fixing a memory leak when destroying an interface
[SCSI] megaraid_sas: Version and Changelog update
...
Fix up trivial conflicts due to whitespace differences in
drivers/scsi/libsas/{sas_ata.c,sas_scsi_host.c}
SBC3r26 contains many changes to the Logical Block Provisioning
interfaces (formerly known as Thin Provisioning ditto). This patch
implements support for both the old and new schemes using the same
heuristic as before (whether the LBP VPD page is present).
The new code also allows the provisioning mode (i.e. choice of command)
to be overridden on a per-device basis via sysfs. Two additional modes
are supported in this version:
- WRITE SAME(10) with the UNMAP bit set
- WRITE SAME(10) without the UNMAP bit set. This allows us to support
devices that predate the TP/LBP enhancements in SBC3 and which work
by way zero-detection
Switching between modes has been consolidated in a helper function that
also updates the block layer topology according to the limitations of
the chosen command.
I experimented with trying WRITE SAME(16) if UNMAP fails, WRITE SAME(10)
if WRITE SAME(16) fails, etc. but found several devices that got
cranky. So for now we'll disable discard if one of the commands
fail. The user still has the option of selecting a different mode in
sysfs.
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
When debugging DIF/DIX it is very helpful to be able to see which DIX
operation is associated with the scsi_cmnd. Include the protection op in
the SCSI command trace.
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
It was always abuse to reuse the plugging infrastructure for this,
convert it to the (new) real API for delaying queueing a bit. A
default delay of 3 msec is defined, to match the previous
behaviour.
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
__blk_run_queue() automatically either calls q->request_fn() directly
or schedules kblockd depending on whether the function is recursed.
blk-flush implementation needs to be able to explicitly choose
kblockd. Add @force_kblockd.
All the current users are converted to specify %false for the
parameter and this patch doesn't introduce any behavior change.
stable: This is prerequisite for fixing ide oops caused by the new
blk-flush implementation.
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Jan Beulich <JBeulich@novell.com>
Cc: James Bottomley <James.Bottomley@HansenPartnership.com>
Cc: stable@kernel.org
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
Instead of just passing 'EIO' for any I/O error we should be
notifying the upper layers with more details about the cause
of this error.
Update the possible I/O errors to:
- ENOLINK: Link failure between host and target
- EIO: Retryable I/O error
- EREMOTEIO: Non-retryable I/O error
- EBADE: I/O error restricted to the I_T_L nexus
'Retryable' in this context means that an I/O error _might_ be
restricted to the I_T_L nexus (vulgo: path), so retrying on another
nexus / path might succeed.
'Non-retryable' in general refers to a target failure, so this
error will always be generated regardless of the I_T_L nexus
it was send on.
I/O errors restricted to the I_T_L nexus might be retried
on another nexus / path, but they should _not_ be queued
if no paths are available.
Signed-off-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
* 'for-2.6.38/core' of git://git.kernel.dk/linux-2.6-block: (43 commits)
block: ensure that completion error gets properly traced
blktrace: add missing probe argument to block_bio_complete
block cfq: don't use atomic_t for cfq_group
block cfq: don't use atomic_t for cfq_queue
block: trace event block fix unassigned field
block: add internal hd part table references
block: fix accounting bug on cross partition merges
kref: add kref_test_and_get
bio-integrity: mark kintegrityd_wq highpri and CPU intensive
block: make kblockd_workqueue smarter
Revert "sd: implement sd_check_events()"
block: Clean up exit_io_context() source code.
Fix compile warnings due to missing removal of a 'ret' variable
fs/block: type signature of major_to_index(int) to major_to_index(unsigned)
block: convert !IS_ERR(p) && p to !IS_ERR_NOR_NULL(p)
cfq-iosched: don't check cfqg in choose_service_tree()
fs/splice: Pull buf->ops->confirm() from splice_from_pipe actors
cdrom: export cdrom_check_events()
sd: implement sd_check_events()
sr: implement sr_check_events()
...
* git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi-misc-2.6: (147 commits)
[SCSI] arcmsr: fix write to device check
[SCSI] lpfc: lower stack use in lpfc_fc_frame_check
[SCSI] eliminate an unnecessary local variable from scsi_remove_target()
[SCSI] libiscsi: use bh locking instead of irq with session lock
[SCSI] libiscsi: do not take host lock in queuecommand
[SCSI] be2iscsi: fix null ptr when accessing task hdr
[SCSI] be2iscsi: fix gfp use in alloc_pdu
[SCSI] libiscsi: add more informative failure message during iscsi scsi eh
[SCSI] gdth: Add missing call to gdth_ioctl_free
[SCSI] bfa: remove unused defintions and misc cleanups
[SCSI] bfa: remove inactive functions
[SCSI] bfa: replace bfa_assert with WARN_ON
[SCSI] qla2xxx: Use sg_next to fetch next sg element while walking sg list.
[SCSI] qla2xxx: Fix to avoid recursive lock failure during BSG timeout.
[SCSI] qla2xxx: Remove code to not reset ISP82xx on failure.
[SCSI] qla2xxx: Display mailbox register 4 during 8012 AEN for ISP82XX parts.
[SCSI] qla2xxx: Don't perform a BIG_HAMMER if Get-ID (0x20) mailbox command fails on CNAs.
[SCSI] qla2xxx: Remove redundant module parameter permission bits
[SCSI] qla2xxx: Add sysfs node for displaying board temperature.
[SCSI] qla2xxx: Code cleanup to remove unwanted comments and code.
...
It seems that zero should be returned if scsi_target_is_busy(starget) is
true, no matter if sdev is on the starved list.
Signed-off-by: Hillf Danton <dhillf@gmail.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
* 'for-linus' of git://git.kernel.dk/linux-2.6-block:
cciss: fix cciss_revalidate panic
block: max hardware sectors limit wrapper
block: Deprecate QUEUE_FLAG_CLUSTER and use queue_limits instead
blk-throttle: Correct the placement of smp_rmb()
blk-throttle: Trim/adjust slice_end once a bio has been dispatched
block: check for proper length of iov entries earlier in blk_rq_map_user_iov()
drbd: fix for spin_lock_irqsave in endio callback
drbd: don't recvmsg with zero length
When stacking devices, a request_queue is not always available. This
forced us to have a no_cluster flag in the queue_limits that could be
used as a carrier until the request_queue had been set up for a
metadevice.
There were several problems with that approach. First of all it was up
to the stacking device to remember to set queue flag after stacking had
completed. Also, the queue flag and the queue limits had to be kept in
sync at all times. We got that wrong, which could lead to us issuing
commands that went beyond the max scatterlist limit set by the driver.
The proper fix is to avoid having two flags for tracking the same thing.
We deprecate QUEUE_FLAG_CLUSTER and use the queue limit directly in the
block layer merging functions. The queue_limit 'no_cluster' is turned
into 'cluster' to avoid double negatives and to ease stacking.
Clustering defaults to being enabled as before. The queue flag logic is
removed from the stacking function, and explicitly setting the cluster
flag is no longer necessary in DM and MD.
Reported-by: Ed Lin <ed.lin@promise.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Acked-by: Mike Snitzer <snitzer@redhat.com>
Cc: stable@kernel.org
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
The usage of TUR has been confusing involving several different
commits updating different parts over time. Currently, the only
differences between scsi_test_unit_ready() and sr_test_unit_ready()
are,
* scsi_test_unit_ready() also sets sdev->changed on NOT_READY.
* scsi_test_unit_ready() returns 0 if TUR ended with UNIT_ATTENTION or
NOT_READY.
Due to the above two differences, sr is using its own
sr_test_unit_ready(), but sd - the sole user of the above extra
handling - doesn't even need them.
Where scsi_test_unit_ready() is used in sd_media_changed(), the code
is looking for device ready w/ media present state which is true iff
TUR succeeds w/o sense data or UA, and when the device is not ready
for whatever reason sd_media_changed() explicitly marks media as
missing so there's no reason to set sdev->changed automatically from
scsi_test_unit_ready() on NOT_READY.
Drop both special handlings from scsi_test_unit_ready(), which makes
it equivalant to sr_test_unit_ready(), and replace
sr_test_unit_ready() with scsi_test_unit_ready(). Also, drop the
unnecessary explicit NOT_READY check from sd_media_changed().
Checking return value is enough for testing device readiness.
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
The error handler is using the test cmd->serial_number == 0 in the
abort routines to signal that the command to be aborted has already
completed normally. This design was to close a race window in the
original error handler where a command could go through the normal
completion routines after it timed out but before error handling was
started.
Mike Anderson pointed out that when we converted our timeout and
softirq completions, we picked up atomicity here because the block
layer now mediates this with the REQ_ATOM_COMPLETE flag and guarantees
that *either* the command times out or our done routine is called, but
ensures we can't get both occurring. That makes the serial number
zero check redundant and it can be removed.
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Deleting a SCSI device on a blocked fc_remote_port (before
fast_io_fail_tmo fires) results in a hanging thread:
STACK:
0 schedule+1108 [0x5cac48]
1 schedule_timeout+528 [0x5cb7fc]
2 wait_for_common+266 [0x5ca6be]
3 blk_execute_rq+160 [0x354054]
4 scsi_execute+324 [0x3b7ef4]
5 scsi_execute_req+162 [0x3b80ca]
6 sd_sync_cache+138 [0x3cf662]
7 sd_shutdown+138 [0x3cf91a]
8 sd_remove+112 [0x3cfe4c]
9 __device_release_driver+124 [0x3a08b8]
10 device_release_driver+60 [0x3a0a5c]
11 bus_remove_device+266 [0x39fa76]
12 device_del+340 [0x39d818]
13 __scsi_remove_device+204 [0x3bcc48]
14 scsi_remove_device+66 [0x3bcc8e]
15 sysfs_schedule_callback_work+50 [0x260d66]
16 worker_thread+622 [0x162326]
17 kthread+160 [0x1680b0]
18 kernel_thread_starter+6 [0x10aaea]
During the delete, the SCSI device is in moved to SDEV_CANCEL. When
the FC transport class later calls scsi_target_unblock, this has no
effect, since scsi_internal_device_unblock ignores SCSI devics in this
state.
It looks like all these are regressions caused by:
5c10e63c94
[SCSI] limit state transitions in scsi_internal_device_unblock
Fix by rejecting offline and cancel in the state transition.
Signed-off-by: Christof Schmitt <christof.schmitt@de.ibm.com>
[jejb: Original patch by Christof Schmitt, modified by Mike Christie]
Cc: Stable Tree <stable@kernel.org>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
* 'for-2.6.37/core' of git://git.kernel.dk/linux-2.6-block: (39 commits)
cfq-iosched: Fix a gcc 4.5 warning and put some comments
block: Turn bvec_k{un,}map_irq() into static inline functions
block: fix accounting bug on cross partition merges
block: Make the integrity mapped property a bio flag
block: Fix double free in blk_integrity_unregister
block: Ensure physical block size is unsigned int
blkio-throttle: Fix possible multiplication overflow in iops calculations
blkio-throttle: limit max iops value to UINT_MAX
blkio-throttle: There is no need to convert jiffies to milli seconds
blkio-throttle: Fix link failure failure on i386
blkio: Recalculate the throttled bio dispatch time upon throttle limit change
blkio: Add root group to td->tg_list
blkio: deletion of a cgroup was causes oops
blkio: Do not export throttle files if CONFIG_BLK_DEV_THROTTLING=n
block: set the bounce_pfn to the actual DMA limit rather than to max memory
block: revert bad fix for memory hotplug causing bounces
Fix compile error in blk-exec.c for !CONFIG_DETECT_HUNG_TASK
block: set the bounce_pfn to the actual DMA limit rather than to max memory
block: Prevent hang_check firing during long I/O
cfq: improve fsync performance for small files
...
Fix up trivial conflicts due to __rcu sparse annotation in include/linux/genhd.h
Some controllers have a hardware limit on the number of protection
information scatter-gather list segments they can handle.
Introduce a max_integrity_segments limit in the block layer and provide
a new scsi_host_template setting that allows HBA drivers to provide a
value suitable for the hardware.
Add support for honoring the integrity segment limit when merging both
bios and requests.
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Jens Axboe <axboe@carl.home.kernel.dk>
we're using a pointer through a freed command to reset the request,
which has shown up as an oops with slab poisoning:
Reported-by: Tejun Heo <tj@kernel.org>
Reported-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Dan's list included:
drivers/scsi/scsi_lib.c +1365 scsi_kill_request(9) warning: variable derefenced in initializer 'cmd'
drivers/scsi/scsi_lib.c +1365 scsi_kill_request(9) warning: variable derefenced before check 'cmd'
We dereference cmd (and possible OOPS if cmd == NULL) before starting the
request so just remove the superfluous debugging code altogether.
[ bart: the potential NULL pointer dereference was finally fixed in
(much later than mine) commit 03b1470 but my patch is still valid ]
Reported-by: Dan Carpenter <error27@gmail.com>
Cc: Jonathan Corbet <corbet@lwn.net>
Cc: Eugene Teo <eteo@redhat.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Cc: James Bottomley <James.Bottomley@HansenPartnership.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
We leak a page allocated for discard on some error conditions
(e.g. scsi_prep_state_check returns BLKPREP_DEFER in
scsi_setup_blk_pc_cmnd).
We unprep on requests that weren't prepped in the error path of
scsi_init_io. It makes the error path to clean up scsi commands messy.
Let's strictly apply the rule that we can't unprep on a request that
wasn't prepped.
Calling just scsi_put_command() in the error path of scsi_init_io() is
enough. We don't set REQ_DONTPREP yet.
scsi_setup_discard_cmnd can safely free a page on the error case with
the above rule.
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
Remove all the trivial wrappers for the cmd_type and cmd_flags fields in
struct requests. This allows much easier grepping for different request
types instead of unwinding through macros.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
* 'for-2.6.34' of git://git.kernel.dk/linux-2.6-block: (38 commits)
block: don't access jiffies when initialising io_context
cfq: remove 8 bytes of padding from cfq_rb_root on 64 bit builds
block: fix for "Consolidate phys_segment and hw_segment limits"
cfq-iosched: quantum check tweak
blktrace: perform cleanup after setup error
blkdev: fix merge_bvec_fn return value checks
cfq-iosched: requests "in flight" vs "in driver" clarification
cciss: Fix problem with scatter gather elements in the scsi half of the driver
cciss: eliminate unnecessary pointer use in cciss scsi code
cciss: do not use void pointer for scsi hba data
cciss: factor out scatter gather chain block mapping code
cciss: fix scatter gather chain block dma direction kludge
cciss: simplify scatter gather code
cciss: factor out scatter gather chain block allocation and freeing
cciss: detect bad alignment of scsi commands at build time
cciss: clarify command list padding calculation
cfq-iosched: rethink seeky detection for SSDs
cfq-iosched: rework seeky detection
block: remove padding from io_context on 64bit builds
block: Consolidate phys_segment and hw_segment limits
...
Except for SCSI no device drivers distinguish between physical and
hardware segment limits. Consolidate the two into a single segment
limit.
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
The block layer calling convention is blk_queue_<limit name>.
blk_queue_max_sectors predates this practice, leading to some confusion.
Rename the function to appropriately reflect that its intended use is to
set max_hw_sectors.
Also introduce a temporary wrapper for backwards compability. This can
be removed after the merge window is closed.
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
Further to the lsml thread titled:
"does scsi_io_completion need to dump sense data for ata pass through (ck_cond =
1) ?"
This is a patch to skip logging when the sense data is
associated with a SENSE_KEY of "RECOVERED_ERROR" and the
additional sense code is "ATA PASS-THROUGH INFORMATION
AVAILABLE". This only occurs with the SAT ATA PASS-THROUGH
commands when CK_COND=1 (in the cdb). It indicates that
the sense data contains ATA registers.
Smartmontools uses such commands on ATA disks connected via
SAT. Periodic checks such as those done by smartd cause
nuisance entries into logs that are:
- neither errors nor warnings
- pointless unless the cdb that caused them are also logged
Signed-off-by: Douglas Gilbert <dgilbert@interlog.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Because of the terrible structuring of scsi-bidi-commands
it breaks some of the life time rules of a scsi-command.
It is now not allowed to free up the block-request before
cleanup and partial deallocation of the scsi-command. (Which
is not so for none bidi commands)
The right fix to this problem would be to make bidi command
a first citizen by allocating a scsi_sdb pointer at scsi command
just like cmd->prot_sdb. The bidi sdb should be allocated/deallocated
as part of the get/put_command (Again like the prot_sdb) and the
current decoupling of scsi_cmnd and blk-request should be kept.
For now make sure scsi_release_buffers() is called before the
call to blk_end_request_all() which might cause the suicide of
the block requests. At best the leak of bidi buffers, at worse
a crash, as there is a race between the existence of the bidi_request
and the free of the associated bidi_sdb.
The reason this was never hit before is because only OSD has the potential
of doing asynchronous bidi commands. (So does bsg but it is never used)
And OSD clients just happen to do all their bidi commands synchronously, up
until recently.
CC: Stable Tree <stable@kernel.org>
Signed-off-by: Boaz Harrosh <bharrosh@panasas.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
A thin provisioned device may temporarily be out of sufficient
allocation units to fulfill a write request. In that case it will
return a space allocation in progress error. Wait a bit and retry the
write.
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Stanse found a potential NULL dereference in scsi_kill_request.
Instead of triggering BUG() in 'if (unlikely(cmd == NULL))' branch,
the kernel will Oops earlier on cmd dereference.
Move the dereferences after the if.
Signed-off-by: Jiri Slaby <jirislaby@gmail.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
When the Integrity check is done in scsi_io_completion it will
set error to -EILSEQ. However, at this point error is no longer
used, and blk_end_request_err has -EIO hardcoded.
It looks like there was just porting mistake with this patch
http://git.kernel.org/?p=linux/kernel/git/torvalds/linux-2.6.git;a=commitdiff;h=3e695f89c5debb735e4ff051e9e58d8fb4e95110
and we meant to send error upwards, so this patch changes the hard
coded EIO to the error variable.
I have only boot tested this patch.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Acked-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
* 'for-2.6.32' of git://git.kernel.dk/linux-2.6-block: (29 commits)
block: use blkdev_issue_discard in blk_ioctl_discard
Make DISCARD_BARRIER and DISCARD_NOBARRIER writes instead of reads
block: don't assume device has a request list backing in nr_requests store
block: Optimal I/O limit wrapper
cfq: choose a new next_req when a request is dispatched
Seperate read and write statistics of in_flight requests
aoe: end barrier bios with EOPNOTSUPP
block: trace bio queueing trial only when it occurs
block: enable rq CPU completion affinity by default
cfq: fix the log message after dispatched a request
block: use printk_once
cciss: memory leak in cciss_init_one()
splice: update mtime and atime on files
block: make blk_iopoll_prep_sched() follow normal 0/1 return convention
cfq-iosched: get rid of must_alloc flag
block: use interrupts disabled version of raise_softirq_irqoff()
block: fix comment in blk-iopoll.c
block: adjust default budget for blk-iopoll
block: fix long lines in block/blk-iopoll.c
block: add blk-iopoll, a NAPI like approach for block devices
...
Update scsi_io_completion() such that it only fails requests till the
next error boundary and retry the leftover. This enables block layer
to merge requests with different failfast settings and still behave
correctly on errors. Allow merge of requests of different failfast
settings.
As SCSI is currently the only subsystem which follows failfast status,
there's no need to worry about other block drivers for now.
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Niel Lambrechts <niel.lambrechts@gmail.com>
Cc: James Bottomley <James.Bottomley@HansenPartnership.com>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
When a request fails we print the sense data but not the actual command
that failed. Add a printout of the operation + CDB for failed commands.
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
If a SCSI ULD driver sets blk_queue_prep_rq(), it should clean it
up itself on remove(), and not from the bus callbacks. This
removes the need to hook into bus->remove(), which should not
be used at the same time as driver->remove().
[jejb: fix sdkp initialisation problem due to mismerge]
Signed-off-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Kay Sievers <kay.sievers@vrfy.org>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Conflicts:
drivers/message/fusion/mptsas.c
fixed up conflict between req->data_len accessors and mptsas driver updates.
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
scsi timeout on two or more devices may cause extremely long execution
time for user applications because SDEV_OFFLINE state is changed to
SDEV_RUNNING state during scsi error recovery procedures triggered by
a bus reset or a host reset of scsi LLD, and scsi timeout can happens
on the same devices many times.
This happens because scsi_internal_device_unblock() changes device's
state to SDEV_RUNNING even if a device in other states than SDEV_BLOCK,
while the following two transitions are required in this function.
SDEV_BLOCK -> SDEV_RUNNING
SDEV_CREATED_BLOCK -> SDEV_CREATED
Otherwise, it returns -EINVAL.
Signed-off-by: Takahiro Yasui <tyasui@redhat.com>
[matthew@wil.cx: supplied rewritten base for patch]
Signed-off-by: Matthew Wilcox <matthew@wil.cx>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
The last request completion cleanup in scsi_lib left an unused
this_count variable in scsi_io_completion().
(It was used before in a code segment that now uses blk_end_request_all())
Signed-off-by: Boaz Harrosh <bharrosh@panasas.com>
Acked-by: Tejun Heo <tj@kernel.org>
Acked-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
Commit c3a4d78c58 introduced
rq->data_len and converted residual count users to it. While
converting, it mistakenly converted scsi_end_request() to finish
requests with residual count when it wants to do is fully complete the
request. Fix it by using blk_end_request_all() instead.
This bug was spotted by Boaz Harrosh.
Signed-off-by: Tejun Heo <tj@kernel.org>
Spotted-by: Boaz Harrosh <bharrosh@panasas.com>
Cc: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Cc: James Bottomley <James.Bottomley@HansenPartnership.com>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
Till now block layer allowed two separate modes of request execution.
A request is always acquired from the request queue via
elv_next_request(). After that, drivers are free to either dequeue it
or process it without dequeueing. Dequeue allows elv_next_request()
to return the next request so that multiple requests can be in flight.
Executing requests without dequeueing has its merits mostly in
allowing drivers for simpler devices which can't do sg to deal with
segments only without considering request boundary. However, the
benefit this brings is dubious and declining while the cost of the API
ambiguity is increasing. Segment based drivers are usually for very
old or limited devices and as converting to dequeueing model isn't
difficult, it doesn't justify the API overhead it puts on block layer
and its more modern users.
Previous patches converted all block low level drivers to dequeueing
model. This patch completes the API transition by...
* renaming elv_next_request() to blk_peek_request()
* renaming blkdev_dequeue_request() to blk_start_request()
* adding blk_fetch_request() which is combination of peek and start
* disallowing completion of queued (not started) requests
* applying new API to all LLDs
Renamings are for consistency and to break out of tree code so that
it's apparent that out of tree drivers need updating.
[ Impact: block request issue API cleanup, no functional change ]
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Rusty Russell <rusty@rustcorp.com.au>
Cc: James Bottomley <James.Bottomley@HansenPartnership.com>
Cc: Mike Miller <mike.miller@hp.com>
Cc: unsik Kim <donari75@gmail.com>
Cc: Paul Clements <paul.clements@steeleye.com>
Cc: Tim Waugh <tim@cyberelk.net>
Cc: Geert Uytterhoeven <Geert.Uytterhoeven@sonycom.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: Laurent Vivier <Laurent@lvivier.info>
Cc: Jeff Garzik <jgarzik@pobox.com>
Cc: Jeremy Fitzhardinge <jeremy@xensource.com>
Cc: Grant Likely <grant.likely@secretlab.ca>
Cc: Adrian McMenamin <adrian@mcmen.demon.co.uk>
Cc: Stephen Rothwell <sfr@canb.auug.org.au>
Cc: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Cc: Borislav Petkov <petkovbb@googlemail.com>
Cc: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Cc: Alex Dubov <oakad@yahoo.com>
Cc: Pierre Ossman <drzeus@drzeus.cx>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Markus Lidel <Markus.Lidel@shadowconnect.com>
Cc: Stefan Weinhuber <wein@de.ibm.com>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Pete Zaitcev <zaitcev@redhat.com>
Cc: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
With the previous changes, the followings are now guaranteed for all
requests in any valid state.
* blk_rq_sectors() == blk_rq_bytes() >> 9
* blk_rq_cur_sectors() == blk_rq_cur_bytes() >> 9
Clean up accessor usages. Notable changes are
* nbd,i2o_block: end_all used instead of explicit byte count
* scsi_lib: unnecessary conditional on request type removed
[ Impact: cleanup ]
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Paul Clements <paul.clements@steeleye.com>
Cc: Pete Zaitcev <zaitcev@redhat.com>
Cc: Alex Dubov <oakad@yahoo.com>
Cc: Markus Lidel <Markus.Lidel@shadowconnect.com>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: James Bottomley <James.Bottomley@HansenPartnership.com>
Cc: Boaz Harrosh <bharrosh@panasas.com>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
With recent unification of fields, it's now guaranteed that
rq->data_len always equals blk_rq_bytes(). Convert all non-IDE direct
users to accessors. IDE will be converted in a separate patch.
Boaz: spotted incorrect data_len/resid_len conversion in osd.
[ Impact: convert direct rq->data_len usages to blk_rq_bytes() ]
Signed-off-by: Tejun Heo <tj@kernel.org>
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Cc: Pete Zaitcev <zaitcev@redhat.com>
Cc: Eric Moore <Eric.Moore@lsi.com>
Cc: Markus Lidel <Markus.Lidel@shadowconnect.com>
Cc: Darrick J. Wong <djwong@us.ibm.com>
Cc: James Bottomley <James.Bottomley@HansenPartnership.com>
Cc: Eric Moore <Eric.Moore@lsi.com>
Cc: Boaz Harrosh <bharrosh@panasas.com>
Cc: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
With recent cleanups, there is no place where low level driver
directly manipulates request fields. This means that the 'hard'
request fields always equal the !hard fields. Convert all
rq->sectors, nr_sectors and current_nr_sectors references to
accessors.
While at it, drop superflous blk_rq_pos() < 0 test in swim.c.
[ Impact: use pos and nr_sectors accessors ]
Signed-off-by: Tejun Heo <tj@kernel.org>
Acked-by: Geert Uytterhoeven <Geert.Uytterhoeven@sonycom.com>
Tested-by: Grant Likely <grant.likely@secretlab.ca>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Tested-by: Adrian McMenamin <adrian@mcmen.demon.co.uk>
Acked-by: Adrian McMenamin <adrian@mcmen.demon.co.uk>
Acked-by: Mike Miller <mike.miller@hp.com>
Cc: James Bottomley <James.Bottomley@HansenPartnership.com>
Cc: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Cc: Borislav Petkov <petkovbb@googlemail.com>
Cc: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Cc: Eric Moore <Eric.Moore@lsi.com>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Cc: Pete Zaitcev <zaitcev@redhat.com>
Cc: Stephen Rothwell <sfr@canb.auug.org.au>
Cc: Paul Clements <paul.clements@steeleye.com>
Cc: Tim Waugh <tim@cyberelk.net>
Cc: Jeff Garzik <jgarzik@pobox.com>
Cc: Jeremy Fitzhardinge <jeremy@xensource.com>
Cc: Alex Dubov <oakad@yahoo.com>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Dario Ballabio <ballabio_dario@emc.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: Rusty Russell <rusty@rustcorp.com.au>
Cc: unsik Kim <donari75@gmail.com>
Cc: Laurent Vivier <Laurent@lvivier.info>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
Implement accessors - blk_rq_pos(), blk_rq_sectors() and
blk_rq_cur_sectors() which return rq->hard_sector, rq->hard_nr_sectors
and rq->hard_cur_sectors respectively and convert direct references of
the said fields to the accessors.
This is in preparation of request data length handling cleanup.
Geert : suggested adding const to struct request * parameter to accessors
Sergei : spotted error in patch description
[ Impact: cleanup ]
Signed-off-by: Tejun Heo <tj@kernel.org>
Acked-by: Geert Uytterhoeven <Geert.Uytterhoeven@sonycom.com>
Acked-by: Stephen Rothwell <sfr@canb.auug.org.au>
Tested-by: Grant Likely <grant.likely@secretlab.ca>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Ackec-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Cc: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Cc: Borislav Petkov <petkovbb@googlemail.com>
Cc: James Bottomley <James.Bottomley@HansenPartnership.com>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
rq->data_len served two purposes - the length of data buffer on issue
and the residual count on completion. This duality creates some
headaches.
First of all, block layer and low level drivers can't really determine
what rq->data_len contains while a request is executing. It could be
the total request length or it coulde be anything else one of the
lower layers is using to keep track of residual count. This
complicates things because blk_rq_bytes() and thus
[__]blk_end_request_all() relies on rq->data_len for PC commands.
Drivers which want to report residual count should first cache the
total request length, update rq->data_len and then complete the
request with the cached data length.
Secondly, it makes requests default to reporting full residual count,
ie. reporting that no data transfer occurred. The residual count is
an exception not the norm; however, the driver should clear
rq->data_len to zero to signify the normal cases while leaving it
alone means no data transfer occurred at all. This reverse default
behavior complicates code unnecessarily and renders block PC on some
drivers (ide-tape/floppy) unuseable.
This patch adds rq->resid_len which is used only for residual count.
While at it, remove now unnecessasry blk_rq_bytes() caching in
ide_pc_intr() as rq->data_len is not changed anymore.
Boaz : spotted missing conversion in osd
Sergei : spotted too early conversion to blk_rq_bytes() in ide-tape
[ Impact: cleanup residual count handling, report 0 resid by default ]
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: James Bottomley <James.Bottomley@HansenPartnership.com>
Cc: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Cc: Borislav Petkov <petkovbb@googlemail.com>
Cc: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Cc: Mike Miller <mike.miller@hp.com>
Cc: Eric Moore <Eric.Moore@lsi.com>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Cc: Doug Gilbert <dgilbert@interlog.com>
Cc: Mike Miller <mike.miller@hp.com>
Cc: Eric Moore <Eric.Moore@lsi.com>
Cc: Darrick J. Wong <djwong@us.ibm.com>
Cc: Pete Zaitcev <zaitcev@redhat.com>
Cc: Boaz Harrosh <bharrosh@panasas.com>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
Now that all block request data transfer is done via bio, rq->data
isn't used. Kill it.
While at it, make the roles of rq->special and buffer clear.
[ Impact: drop now unncessary field from struct request ]
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Boaz Harrosh <bharrosh@panasas.com>
There are many [__]blk_end_request() call sites which call it with
full request length and expect full completion. Many of them ensure
that the request actually completes by doing BUG_ON() the return
value, which is awkward and error-prone.
This patch adds [__]blk_end_request_all() which takes @rq and @error
and fully completes the request. BUG_ON() is added to to ensure that
this actually happens.
Most conversions are simple but there are a few noteworthy ones.
* cdrom/viocd: viocd_end_request() replaced with direct calls to
__blk_end_request_all().
* s390/block/dasd: dasd_end_request() replaced with direct calls to
__blk_end_request_all().
* s390/char/tape_block: tapeblock_end_request() replaced with direct
calls to blk_end_request_all().
[ Impact: cleanup ]
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Russell King <rmk@arm.linux.org.uk>
Cc: Stephen Rothwell <sfr@canb.auug.org.au>
Cc: Mike Miller <mike.miller@hp.com>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Jeff Garzik <jgarzik@pobox.com>
Cc: Rusty Russell <rusty@rustcorp.com.au>
Cc: Jeremy Fitzhardinge <jeremy@xensource.com>
Cc: Alex Dubov <oakad@yahoo.com>
Cc: James Bottomley <James.Bottomley@HansenPartnership.com>
We cannot call blk_plug_device from scsi_target_queue_ready
because the q lock is not held. And we do not need to call
it from there because when we return 0, the scsi_request_fn
not_ready handling will plug the queue for us if needed.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
We have a problem with recovered error handling in that any command
which goes down as BLOCK_PC but which returns a sense code of RECOVERED
ERROR gets completed with -EIO. For actual SG_IO commands, this doesn't
matter at all, since the error return code gets dropped in favour of
req->errors which contain the SCSI completion code.
However, if this command is part of the block system, then it will pay
attention to the returned error code. In particularly if a SYNCHRONIZE
CACHE from a barrier command completes with RECOVERED ERROR, the
resulting -EIO on the barrier causes block to error the request and
return it to the filesystem. Fix this by converting the -EIO for
recovered error to zero, plus remove the printing of this from sd and sr
so the message isn't double printed.
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
No one uses scsi_execute_async with data transfer now. We can remove
scsi_req_map_sg.
Only scsi_eh_lock_door uses scsi_execute_async. scsi_eh_lock_door
doesn't handle sense and the callback. So we can remove
scsi_io_context too.
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Instead of terminating after five retries, commands terminated by
ABORTED_COMMAND sense are retrying forever. The problem was
introduced by:
commit b60af5b0ad
Author: Alan Stern <stern@rowland.harvard.edu>
Date: Mon Nov 3 15:56:47 2008 -0500
[SCSI] simplify scsi_io_completion()
Which introduced an error whereby ABORTED_COMMAND now gets erroneously
retried in scsi_io_completion. Fix this by returning the behaviour
back to the default no retry.
Reported-by: Sitsofe Wheeler <sitsofe@yahoo.com>
Tested-by: Sitsofe Wheeler <sitsofe@yahoo.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Andrew Vaszquez said:
> There's a problem that is causing commands returned by the LLD with
> a DID_RESET status to be reissued with cleared cmd->sdb data which
> in our tests are manifesting in firmware detected overruns. Here's
> a snippet of a READ_10 scsi_cmnd upon completion by the storage
The problem is caused by:
commit b60af5b0ad
Author: Alan Stern <stern@rowland.harvard.edu>
Date: Mon Nov 3 15:56:47 2008 -0500
[SCSI] simplify scsi_io_completion()
Because scsi_release_buffers() is called before commands that go
through the ACTION_RETRY and ACTION_DELAYED_RETRY legs are requeued.
However, they're not re-prepared, so nothing ever reallocates the
buffer resources to them. Fix this by releasing the buffers only if
we're not going to go down these legs (but scsi_release_buffers() on
all legs including two in scsi_end_request(); this latter needs a
special version __scsi_release_buffers() because the final one can be
called after the request has been freed, so the bidi test in
scsi_release_buffers(), which touches the request has to be skipped).
Reported-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
patch
commit b60af5b0ad
Author: Alan Stern <stern@rowland.harvard.edu>
Date: Mon Nov 3 15:56:47 2008 -0500
[SCSI] simplify scsi_io_completion()
broke DIX error handling. Also, we are now using EILSEQ to indicate
integrity errors to the upper layers (as opposed to regular EIO
failures). This allows filesystems to inspect buffers and decide
whether to retry the I/O. Update scsi_io_completion() accordingly.
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
A bug was introduced by
commit b60af5b0ad
Author: Alan Stern <stern@rowland.harvard.edu>
Date: Mon Nov 3 15:56:47 2008 -0500
[SCSI] simplify scsi_io_completion()
because the simplification uses scsi_queue_insert(). The problem with
this function is that it expects to be called from the completion path
while the command is still outstanding, so it decrements the device
and host busy counts to do the requeue. The problem is that
scsi_io_completion() is a path executed well after these counts have
*already* been decremented, leading to a double decrement if the
command goes down any error path leading to ACTION_DELAYED_RETRY.
The fix is to allow a private function __scsi_queue_insert() with a
flag to say whether the busy counters should be decremented. This is
made static to scsi_lib.c to discourage other use.
Reported-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
This patch (as1191) adds a missing "default" case in
scsi_io_completion(), thereby fixing an "uninitialized variable"
error. It also adds a missing newline to a log entry.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
scsi_execute() and scsi_execute_req() discard the residual length
information. Some callers need it. This adds residual argument
(optional) to scsi_execute and scsi_execute_req.
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
This patch (as1142b) consolidates a lot of repetitious code in
scsi_io_completion(). It also fixes a few comments. Most
importantly, however, it clearly distinguishes among the three sorts
of retries that can be done when a command fails to complete:
Unprepare the request and resubmit it, so that a new
command will be created for it.
Requeue the request directly so that it will be retried
immediately using the same command.
Requeue the request so that it will be retried following
a short delay.
Complete the remainder of the request with an I/O error.
[jejb: Updates
1. For several error conditions, we would now print the sense twice
in slightly different ways, so unify the location of sense
printing.
2. I added more descriptions to actual failure conditions for
better debugging
3. according to spec, ABORTED_COMMAND is supposed to be retried
(except on DIF failure). Our old behaviour of erroring it looks
to be a bug.
4. I'd prefer not to default initialise the action variable because
that ensures that every leg of the error handler has an
associated action and the compiler will warn if someone later
accidentally misses one or removes one.
]
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
It's called under that lock everywhere else and it does alter the
request state, so it should be.
This one occurance in scsi_requeue_command() could open a window where
req->special is set to NULL while the requests is going through either
timeout or completion processing leading to NULL pointer derefs of the
sort complained of in bugzillas 12020 and 12195.
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Close possible infinite loop with interrupts off when devices are
added back to the starved list.
Fixes: http://bugzilla.kernel.org/show_bug.cgi?id=11898
Reported-by: <alex.shi@intel.com>
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
This patch implements q->lld_busy_fn() for scsi mid layer to export
its busy state for request stacking drivers.
For efficiency, no lock is taken to check the busy state of
shost/starget/sdev, since the returned value is not guaranteed and
may be changed after request stacking drivers call the function,
regardless of taking lock or not.
When scsi can't dispatch I/Os anymore and needs to kill I/Os
(e.g. !sdev), scsi needs to return 'not busy'.
Otherwise, request stacking drivers may hold requests forever.
Signed-off-by: Kiyoshi Ueda <k-ueda@ct.jp.nec.com>
Signed-off-by: Jun'ichi Nomura <j-nomura@ce.jp.nec.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
This patch refactors the busy checking codes of scsi_device,
Scsi_Host and scsi_target. There should be no functional change.
This is a preparation for another patch which exports scsi's busy
state to the block layer for request stacking drivers.
Signed-off-by: Kiyoshi Ueda <k-ueda@ct.jp.nec.com>
Signed-off-by: Jun'ichi Nomura <j-nomura@ce.jp.nec.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
On Tue, 12 Aug 2008 15:08:14 +0200
Giuliano Pochini <pochini@shiny.it> wrote:
> Fujitsu magneto-optical drive, Adaptec 29160 and
> Linux Jay 2.6.26 #7 SMP Sun Aug 10 18:34:22 CEST 2008 ppc 7455, altivec supported PowerMac3,6 GNU/Linux
>
> When I insert a disk and I mount it, scsi_test_unit_ready() is called and
> the do-while loop gets sshdr->sense_key == UNIT_ATTENTION in the first
> cycle and 0 in the second one. So the if below misses the UNIT_ATTENTION
> and sdev->changed = 1 is not executed. At this point bad things can
> happen... I'm not sure how to fix this. Any clue ?
The problem is essentially caused by us eating UNIT_ATTENTION
conditions in scsi_test_unit_ready(). Fix by updating the ->changed
flag when this happens if the media is removable.
[pochini@shiny.it: updates to tidy up patch]
Signed-off-by: Giuliano Pochini <pochini@shiny.it>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
This checks the errors the scsi-ml determined were retryable
and returns if we should fast fail it based on the request
fail fast flags.
Without the patch, drivers like lpfc, qla2xxx and fcoe would return
DID_ERROR for what it determines is a temporary communication problem.
There is no loss of connectivity at that time and the driver thinks
that it would be fast to retry at the driver level. SCSI-ml will however
sees fast fail on the request and DID_ERROR and will fast fail the io.
This will then cause dm-multipath to fail the path and possibley switch
target controllers when we should be retrying at the scsi layer.
We also were fast failing device errors to dm multiapth when
unless the scsi_dh modules think otherwis we want to retry at
the scsi layer because multipath can only retry the IO like scsi
should have done. multipath is a little dumber though because it
does not what the error was for and assumes that it should fail
the paths.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
SCSI-ml manages the queueing limits for the device and host, but
does not do so at the target level. However something something similar
can come in userful when a driver is transitioning a transport object to
the the blocked state, becuase at that time we do not want to queue
io and we do not want the queuecommand to be called again.
The patch adds code similar to the exisiting SCSI_ML_*BUSY handlers.
You can now return SCSI_MLQUEUE_TARGET_BUSY when we hit
a transport level queueing issue like the hw cannot allocate some
resource at the iscsi session/connection level, or the target has temporarily
closed or shrunk the queueing window, or if we are transitioning
to the blocked state.
bnx2i, when they rework their firmware according to netdev
developers requests, will also need to be able to limit queueing at this
level. bnx2i will hook into libiscsi, but will allocate a scsi host per
netdevice/hba, so unlike pure software iscsi/iser which is allocating
a host per session, it cannot set the scsi_host->can_queue and return
SCSI_MLQUEUE_HOST_BUSY to reflect queueing limits on the transport.
The iscsi class/driver can also set a scsi_target->can_queue value which
reflects the max commands the driver/class can support. For iscsi this
reflects the number of commands we can support for each session due to
session/connection hw limits, driver limits, and to also reflect the
session/targets's queueing window.
Changes:
v1 - initial patch.
v2 - Fix scsi_run_queue handling of multiple blocked targets.
Previously we would break from the main loop if a device was added back on
the starved list. We now run over the list and check if any target is
blocked.
v3 - Rediff for scsi-misc.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
* git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi-misc-2.6: (37 commits)
[SCSI] zfcp: fix double dbf id usage
[SCSI] zfcp: wait on SCSI work to be finished before proceeding with init dev
[SCSI] zfcp: fix erp list usage without using locks
[SCSI] zfcp: prevent fc_remote_port_delete calls for unregistered rport
[SCSI] zfcp: fix deadlock caused by shared work queue tasks
[SCSI] zfcp: put threshold data in hba trace
[SCSI] zfcp: Simplify zfcp data structures
[SCSI] zfcp: Simplify get_adapter_by_busid
[SCSI] zfcp: remove all typedefs and replace them with standards
[SCSI] zfcp: attach and release SAN nameserver port on demand
[SCSI] zfcp: remove unused references, declarations and flags
[SCSI] zfcp: Update message with input from review
[SCSI] zfcp: add queue_full sysfs attribute
[SCSI] scsi_dh: suppress comparison warning
[SCSI] scsi_dh: add Dell product information into rdac device handler
[SCSI] qla2xxx: remove the unused SCSI_QLOGIC_FC_FIRMWARE option
[SCSI] qla2xxx: fix printk format warnings
[SCSI] qla2xxx: Update version number to 8.02.01-k8.
[SCSI] qla2xxx: Ignore payload reserved-bits during RSCN processing.
[SCSI] qla2xxx: Additional residual-count corrections during UNDERRUN handling.
...
Right now SCSI and others do their own command timeout handling.
Move those bits to the block layer.
Instead of having a timer per command, we try to be a bit more clever
and simply have one per-queue. This avoids the overhead of having to
tear down and setup a timer for each command, so it will result in a lot
less timer fiddling.
Signed-off-by: Mike Anderson <andmike@linux.vnet.ibm.com>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
Brian King <brking@linux.vnet.ibm.com> reported that fibre channel
devices can oops during scanning if their ports block (because the
device goes from CREATED -> BLOCK -> RUNNING rather than CREATED ->
BLOCK -> CREATED).
Fix this by adding a new state: CREATED_BLOCK which can only transition
back to CREATED and disallow the CREATED -> BLOCK transition. Now both
the created and blocked states that the mid-layer recognises can include
CREATED_BLOCK.
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Christoph Hellwig