The hardware I/O has to be open-coded due to registers of unequal sizes.
Other than that, the transition is straight forward.
Signed-off-by: Daniel Mack <zonque@gmail.com>
Acked-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
The ADAU1701 has 2 hardware pins to configure the PLL mode in accordance
to the MCLK-to-LRCLK ratio. These pins have to be stable before the chip
is released from reset, and a full reset cycle, including a new firmware
download is needed whenever they change.
This patch adds GPIO properties to the DT bindings of the Codec, and
implements makes the set_sysclk memorize the configured sysclk.
Because the run-time parameters are unknown at probe time, the first
firmware download is postponed to the first hw_params call, when the
driver can determine the mclk/lrclk divider. Subsequent downloads
are only issued when the divider configuration changes.
Signed-off-by: Daniel Mack <zonque@gmail.com>
Acked-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
The chip needs a new download after each reset, so the code to do that
needs to live in adau1701_reset().
Signed-off-by: Daniel Mack <zonque@gmail.com>
Acked-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
The TAS5086 has two alternative modes to start its PWM channels, Mid-Z
and Low-Z. Which one to use depends on how the PWM power stages are
connected to the TAS5086.
This patch adds 6 optional boolean properties to the DT bindings of the
driver which allow the user to configure each individual channel to the
Mid-Z scheme, and leaves all the others to the default (Low-Z).
Signed-off-by: Daniel Mack <zonque@gmail.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
The TAS5086 has two muxes, one for connecting I2S inputs to internal
channels, and another one for selecting which internal channel should
be routed to which PWM output pin.
This patch adds DAPM widgets and routes for this driver.
Signed-off-by: Daniel Mack <zonque@gmail.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Add register definitions for input and output mux registers, and rewrite
the tas5086_accessible_reg() function.
Signed-off-by: Daniel Mack <zonque@gmail.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
In order to support registers of unequal sizes, the I2C I/O has to be
open-coded.
Signed-off-by: Daniel Mack <zonque@gmail.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
To reduce pop noise during playback stream start and stop the codec needs
to have the digital_mute callback implemented.
The codec need to be muted before the CPU dai has been stopped (McPDM).
Stopping the McPDM will generate a pop on the codec since no signal on the
PDM bus means full negative amplitude.
By managing the mute/unmute state of the outputs we can decrease the amount
of pop noise when playback starts or stops.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
We need to free the irq at twl6040_remove() which is called when the machine
driver has been removed (the card has been removed).
If we fail to do that, next time when the machine driver is loaded the
codec's probe will fail since the irq has been already requested.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Replace the leftover CONFIG_SND_SOC_OMAP_HDMI_CODEC in
sound/soc/omap/Kconfig with CONFIG_SND_SOC_HDMI_CODEC, which was
forgotten in the commit bf7c6e6c.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This pull request moves DaVinci EDMA library to
arch/arm/common so it can be used by OMAP based AM335x.
This is a temporary step until all drivers are converted
to use the dmaengine driver in drivers/dma/edma.c.
Several drivers like SPI, MMC/SD have already been converted.
Some like audio are pending.
The other two patches in the pull request are cleanup in nature.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.10 (GNU/Linux)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=BH9M
-----END PGP SIGNATURE-----
Merge tag 'davinci-for-v3.11/soc-v2' of git://git.kernel.org/pub/scm/linux/kernel/git/nsekhar/linux-davinci into next/soc
From Sekhar Nori:
DaVinci SoC changes for v3.11
This pull request moves DaVinci EDMA library to
arch/arm/common so it can be used by OMAP based AM335x.
This is a temporary step until all drivers are converted
to use the dmaengine driver in drivers/dma/edma.c.
Several drivers like SPI, MMC/SD have already been converted.
Some like audio are pending.
The other two patches in the pull request are cleanup in nature.
* tag 'davinci-for-v3.11/soc-v2' of git://git.kernel.org/pub/scm/linux/kernel/git/nsekhar/linux-davinci:
ARM: edma: remove unused transfer controller handlers
ARM: davinci: move private EDMA API to arm/common
ARM: davinci: remove __init atrribute from function declaration
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Move mach-davinci/dma.c to common/edma.c so it can be used
by OMAP (specifically AM33xx) as well.
Signed-off-by: Matt Porter <mporter@ti.com>
Acked-by: Chris Ball <cjb@laptop.org> # davinci_mmc.c
Acked-by: Mark Brown <broonie@linaro.org>
Acked-by: Olof Johansson <olof@lixom.net>
[nsekhar@ti.com: dropped davinci sffsdr changes]
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Commit 75096579c3 ("lib: devres: Introduce devm_ioremap_resource()")
introduced devm_ioremap_resource() and deprecated the use of
devm_request_and_ioremap().
devm_request_mem_region is called in devm_ioremap_resource(). Hence that
part can also be removed.
Since devm_ioremap_resource prints error message on failure, there is
no need to print an explicit warning message.
Signed-off-by: Tushar Behera <tushar.behera@linaro.org>
CC: alsa-devel@alsa-project.org
CC: Liam Girdwood <lgirdwood@gmail.com>
CC: Mark Brown <broonie@kernel.org>
Signed-off-by: Mark Brown <broonie@linaro.org>
sffsdr machine support does not build since at least v2.6.36
(~3 years). There is little hope of it being fixed, so remove
the support.
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
support for the DMA40. Now with MUSB and some platform
data removal.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.10 (GNU/Linux)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=rn7t
-----END PGP SIGNATURE-----
Merge tag 'ux500-dma40-for-arm-soc-2' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-stericsson into next/drivers
From Linus Walleij:
Second set of DMA40 changes: refactorings and device tree
support for the DMA40. Now with MUSB and some platform
data removal.
* tag 'ux500-dma40-for-arm-soc-2' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-stericsson:
dmaengine: ste_dma40: Fetch disabled channels from DT
dmaengine: ste_dma40: Fetch the number of physical channels from DT
ARM: ux500: Stop passing DMA platform data though AUXDATA
dmaengine: ste_dma40: Allow memcpy channels to be configured from DT
dmaengine: ste_dma40_ll: Replace meaningless register set with comment
dmaengine: ste_dma40: Convert data_width from register bit format to value
dmaengine: ste_dma40_ll: Use the BIT macro to replace ugly '(1 << x)'s
ARM: ux500: Remove recently unused stedma40_xfer_dir enums
dmaengine: ste_dma40: Replace ST-E's home-brew DMA direction defs with generic ones
ARM: ux500: Replace ST-E's home-brew DMA direction definition with the generic one
dmaengine: ste_dma40: Use the BIT macro to replace ugly '(1 << x)'s
ARM: ux500: Remove empty function u8500_of_init_devices()
ARM: ux500: Remove ux500-musb platform registation when booting with DT
usb: musb: ux500: add device tree probing support
usb: musb: ux500: attempt to find channels by name before using pdata
usb: musb: ux500: harden checks for platform data
usb: musb: ux500: take the dma_mask from coherent_dma_mask
usb: musb: ux500: move the MUSB HDRC configuration into the driver
usb: musb: ux500: move channel number knowledge into the driver
Reported-by: Dennis May <dennis.may@wolfsonmicro.com>
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
This part of bias settings are essential for WM8962 to power up. Without it
"wm8962 0-001a: DC servo timed out" might be prompted due to power-up failure
that happens to FLL if being used.
The driver's also bringing the bias down in the suspend path so it needs to be
powered up in the resume path for symmetry.
According to dapm_pre_sequence_async(), DAPM would call pm_runtime_get_sync()
to let driver finish the bias settings in pm_runtime_resume() before the bias
level being set to STANDBY. So no need to worry about disordered settings for
VMID of WM8962.
Signed-off-by: Nicolin Chen <b42378@freescale.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
The power up/down sequence order for DAPM switch widgets is not explicitly
initialized, causing them to be run always as the first widget type for both
power up and down. Move it to the same position in the sequence as other mixer
widget types.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
Since commit 85762e71 ("ASoC: dapm: Implement mixer control sharing") the
long_name field of the snd_soc_dapm_path struct is unused. All of the name
handling now happens entirely in dapm_create_or_share_mixmux_kcontrol(). So we
can remove the long_name field from the snd_soc_dapm_path struct.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
We have the same code for freeing a DAPM path in three different locations.
Introduce a new helper function to take care of this.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
The condition 'i == item' is only true when, well, 'i' equals 'item'.
So just use 'item' directly as the index into the array.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
The private data containing the widget list that is a assigned to a DAPM
kcontrol is never freed. Setup the private_free for DAPM kcontrols to take care
of this.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
The individual component drivers are only useful with a machine driver and
should be selected by the machine drivers so shouldn't have help text of
their own in order to hide them in interactive configuration.
Signed-off-by: Mark Brown <broonie@linaro.org>
In struct snd_soc_card zylonite .owner is assigned THIS_MODULE
twice, remove one of them.
Signed-off-by: Emil Goode <emilgoode@gmail.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Also fix return values for headphone switch updates.
Signed-off-by: Nicolin Chen <b42378@freescale.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Cc: stable@vger.kernel.org
This fixes:
975:9: sparse: Using plain integer as NULL pointer
1917:24: sparse: symbol 'rt5640_aif_dai_ops' was not declared. Should it be static?
1924:27: sparse: symbol 'rt5640_dai' was not declared. Should it be static?
2079:19: sparse: symbol 'rt5640_i2c_driver' was not declared. Should it be static?
Reported-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
The patch that resulted in
bfcc74e (ASoC: SPEAr spdif_{in,out}: use devm for clk and a few
more cleanups)
was broken and applied on a newer tree than it was created for. So
bfcc74e introduced unbalanced clk handling, two warnings about unused
variables and passed 3 arguments to a function only taking 2. This
commit fixes that.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
Initially, this binding and driver only describe/support playback to
headphones and speakers.
This driver will support Beaver and Dalmore.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Modify the RT5640 driver to parse platform data from device tree. Write
a DT binding document to describe those properties.
Slight re-ordering of rt5640_i2c_probe() to better fit the DT parsing.
Since ldo1_en is optional, guard usage of it with gpio_is_valid(), rather
than open-coding an if (gpio) check.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Certain use cases may require specific DRE settings so expose control
of these.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
This patch adds the ALC5640 codec driver.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Bard Liao <bardliao@realtek.com>
Tested-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Implement a DMA slave config prepare routine, as until now the MSP
driver depended on the DMA controller completing the channel
configuration on its own, but this is not the case anymore since the
recent DMA driver updates.
Signed-off-by: Fabio Baltieri <fabio.baltieri@linaro.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Mark Brown <broonie@linaro.org>
Add a field with the tx/rx register address to the DMA parameters
structure, and set it to the correct address during device
initialization.
This address used to be hardcoded in the DMA controller driver, it now
needs to be explicitly figured out by the device driver.
Signed-off-by: Fabio Baltieri <fabio.baltieri@linaro.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Mark Brown <broonie@linaro.org>
Move struct ux500_msp_dma_params declaration from ux500_msp_i2s_drvdata
to ux500_msp, this saves some confusing pointer passing and allows to
access all DMA configuration fields from ux500_msp_i2s.
Signed-off-by: Fabio Baltieri <fabio.baltieri@linaro.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Mark Brown <broonie@linaro.org>
This patch adds Kconfig and Makefile to support SPEAr Audio driver.
Signed-off-by: Rajeev Kumar <rajeev-dlh.kumar@st.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
This driver is useless if both SPI and I2C are not configured.
Thus don't build this driver if both SPI and I2C are not configured.
This patch silences below build warning if both SPI and I2C are not configured.
CC sound/soc/codecs/adav80x.o
sound/soc/codecs/adav80x.c:842:12: warning: 'adav80x_bus_probe' defined but not used [-Wunused-function]
sound/soc/codecs/adav80x.c:863:12: warning: 'adav80x_bus_remove' defined but not used [-Wunused-function]
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Acked-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
Some runtime-determined constraints might need to be satisfied prior to
firmware loading, so the actual download and releasing the device from
reset has to be postponed. Factor it out first, so we have everything at
one place.
This also changes the behaviour in a way that adau1701_i2c_probe() will
assert the reset line, and wait for the codec probe to release it.
Signed-off-by: Daniel Mack <zonque@gmail.com>
Acked-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
Otherwise, ssm2518_set_tdm_slot() always returns error if slots != 0.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Acked-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
This is the initial imx-wm8962 device-tree-only machine driver working with
fsl_ssi driver. More features can be added on top of it later.
Signed-off-by: Nicolin Chen <b42378@freescale.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Commit 9e13f345 (ASoC: sgtl5000: Let the codec acquire its clock) removed the
clk_put calls.
Let's use devm_clk_get() instead, so that we do not need to call them anymore.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
We should use i2c_get_clientdata() to get the codec private structure.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
After the device has been reset we need to repeat the same
initialisation we do on probe to make sure that the device is in
a known state.
Tested-by: Nicolin Chen <b42378@freescale.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
On a mx6qsabrelite board the following error happens on probe:
sgtl5000: probe of 0-000a failed with error -5
imx-sgtl5000 sound.13: ASoC: CODEC (null) not registered
imx-sgtl5000 sound.13: snd_soc_register_card failed (-517)
platform sound.13: Driver imx-sgtl5000 requests probe defer
Prior to reading the codec ID we need to turn the SYS_MCLK clock, so let's
enable the codec clock inside sgtl5000_i2c_probe().
Also remove the codec clock enable/disable functions from the machine driver.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
When calling snd_soc_dapm_sync(), it eventually tries to lock the same mutex
already locked in snd_soc_dapm_put_volsw_aic3x() and a deadlock occurs. By
moving the mutex unlock to just before snd_soc_dapm_sync(), this deadlock is
prevented. This problem was introduced in Linux 3.5
Signed-off-by: Andreas Irestål <Andreas.Irestal@axis.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Even though they are virtual widgets DAI widgets still get counted for the
DAPM context power management so we can't just use the active state to
check if they should be powered as they may not be part of a complete path.
Instead split them into input and output widgets and do the same power
checks as we perform on AIFs.
Reported-by: Stephen Warren <swarren@nvidia.com>
Tested-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Document the device tree binding for the WM8962 codec, and modify the
driver to extract platform data from the device tree, if present.
Based on work of WM8903 by Stephen Warren <swarren@nvidia.com>
Signed-off-by: Nicolin Chen <b42378@freescale.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Embed a copy of struct wm8962_pdata in stuct wm8962_priv
so that there's no need to check validity of pdata any more.
Signed-off-by: Nicolin Chen <b42378@freescale.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Otherwise the functions will be defined but unreferenced when runtime PM
is disabled, generating warnings.
Signed-off-by: Mark Brown <broonie@linaro.org>
When the regulators have been disabled mark the device as cache only so
that we don't try to interact with the hardware.
Signed-off-by: Mark Brown <broonie@linaro.org>
to support HDMI on CSR SiRFprimaII and atlasVI, we need one more HDMI pseudo
codec, rather than add a new driver, we can make omap HDMI codec common for
other SoCs as well. then the omap-hdmi codec becomes a generic HDMI pseudo-
codec as HDMI audio features depend on HDMI specification not on SoCs.
Signed-off-by: Barry Song <Baohua.Song@csr.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
All sources and sinks should enable SYSCLK.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Tegra HW needs clocks etc. active when touching registers. Make sure they
are active during resume, by calling pm_runtime_get_sync() before touching
HW.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
The VAG_POWER must be enabled after all other bits in CHIP_ANA_POWER
and disabled before any other bit in CHIP_ANA_POWER. See the SGTL5000
datasheet (Table 31, BIT 7, page 42-43). Failing to follow this order
will result in ugly loud "POP" noise at the end of playback.
To achieve such order, use the _PRE and _POST DAPM widgets to trigger
the power_vag_event, where the event type check has to be fixed
accordingly as well.
Signed-off-by: Marek Vasut <marex@denx.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
When a DMA client requests and configures a DMA channel, it requests
data_width in Bytes. The DMA40 driver then swiftly converts it over to
the necessary register bit value. Unfortunately, for any subsequent
calculations we have to shift '1' by the bit pattern (1 << data_width)
times to make any sense of it.
This patch flips the semantics on its head and only converts the value
to its respective register bit pattern when writing to registers. This
way we can use the true data_width (in Bytes) value.
Cc: Dan Williams <djbw@fb.com>
Cc: Per Forlin <per.forlin@stericsson.com>
Cc: Rabin Vincent <rabin@rab.in>
Acked-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Add tegra30_i2s_{suspend,resume}. These use regcache functions to
restore all HW registers after power loss during a suspend/resume cycle.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Add tegra30_ahub_{suspend,resume}. These use regcache functions to
restore all HW registers after power loss during a suspend/resume cycle.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
'mcasp_dt_ids' is always compiled in. Hence of_match_ptr is not
necessary.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Mark Brown <broonie@linaro.org>
Both clear the IRQ as being a wake source when we are finished with it
and include a missing header file that is required.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
When declaring playback and capture capabilities check for both CODEC
side and CPU side support rather than only checking for CODEC side
support. While it is unusual some CPUs do have unidirectional DAIs.
Reported-by: Fabio Estevam <fabio.estevam@freescale.com>
Tested-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Liam Girdwood <liam.r.girdwood@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
For systems which do not have a jack detection feature allow some debounce
to be specified before we perform accessory identification, improving
robustness without impacting button detection responsiveness.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
There is loopback control within the audio interfaces, provide control of
this as there are some obscure scenarios where this could be used in
production.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Now that the bf5xx-i2s driver supports TDM mode and all users of the bf5xx-tdm
driver have been switch over to using the bf5xx-i2s driver there is no need to
keep the b5fxx-tdm driver around.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The bf5xx-i2s driver now has support for TDM mode and the bf5xx-tdm driver is
going to be removed soon, so switch the driver over to bf5xx-i2s.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The bf5xx-i2s driver now has support for TDM mode and the bf5xx-tdm driver is
going to be removed soon, so switch the driver over to bf5xx-i2s.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The bf5xx-i2s{,-pcm} and bf5xx-tdm{-pcm} drivers are nearly identical. Both are
for the same hardware each supporting a slight different subset of the hardware.
The bf5xx-i2s driver supports 2 channel I2S mode while the bf5xx-tdm driver
supports TDM mode and channel remapping. This patch adds support for TDM mode
and channel remapping to the bf5xx-i2s driver so that we'll eventually be able
to retire the bf5xx-tdm driver. Unfortunately the hardware is fixed to using 8
channels in TDM mode. The bf5xx-tdm driver jumps through a few hoops to make it
work well with other channel counts as well:
* Don't support mmap
* Translate between internal frame size (which is always 8 * sample_size)
and ALSA frame size (which depends on the channel count)
* Have special copy and silence callbacks which are aware of the mismatch
between internal and ALSA frame size
* Reduce the maximum buffer size to ensure that there is enough headroom for
dummy data.
The bf5xx-i2s driver is going to use the same mechanisms when being used int
TDM mode.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Use snd_pcm_lib_preallocate_pages_for_all() for pre-allocating the DMA buffers
instead of re-implementing the same functionality. Note that there is no need
to call snd_pcm_lib_free_pages_for_all() since the ALSA core takes care of this
for us.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
There is no need to always allocate the maximum buffer size. While we are at it
also pass errors returned by snd_pcm_lib_malloc_pages() on to the upper layers.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Since the hardware supports it there is no need to artificially limit this to
just being able to set the same mask for both tx and rx.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Using dev_{err,dbg} instead of pr_{error,debug} makes it easier to recognize
which device created the message.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The structs defined in these files are completely unused, so remove both the
structs and the files.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Support for omap2evm was removed in v3.0. But only one of its two
lines in this Makefile was removed. Remove the second line too.
Signed-off-by: Paul Bolle <pebolle@tiscali.nl>
Acked-by: Jarkko Nikula <jarkko.nikula@bitmer.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The DSPs IRQ should be a wake source as several of the possible
algorithms may run whilst the AP is asleepi and require to wake the AP
to push or pull more data, such as compressed playback.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Provide a bit of debounce to handle pathological cases with slow input
better by allowing the microphone detection to run for a bit longer.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Nicolas Schichan <nschichan@freebox.fr>
Acked-by: Brian Austin <brian.austin@cirrus.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Nicolas Schichan <nschichan@freebox.fr>
Acked-by: Brian Austin <brian.austin@cirrus.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The default register value for MASTERA_VOL is 0x00, the same as
MASTERB_VOL.
Signed-off-by: Nicolas Schichan <nschichan@freebox.fr>
Acked-by: Brian Austin <brian.austin@cirrus.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: stable@vger.kernel.org
Daniel Mack