Sync kernel codes to the same with 590eaf1fec ("Init Repo base on
linux 5.4.32 long term, and add base tlinux kernel interfaces."), which
is from tk4, and it is the base of tk4.
Signed-off-by: Jianping Liu <frankjpliu@tencent.com>
So far we didn't support mode USXGMII, and in order to not break few
boards mode XGMII was accepted for the AQR107 family even though it
doesn't support XGMII. Add USXGMII support to the Aquantia PHY driver
and warn if XGMII mode is set.
v2:
- add warning if XGMII mode is set
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
XGMII interface mode no longer works on AQR107 after the recent changes,
adding back support.
Fixes: 570c8a7d53 ("net: phy: aquantia: check for supported interface modes in config_init")
Signed-off-by: Madalin Bucur <madalin.bucur@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
genphy_c45_aneg_done() is used by phylib as fallback for c45 PHY's if
callback aneg_done isn't defined. So we don't have to set this
explicitly. Same for genphy_c45_pma_read_abilities().
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The AQR107 family has SGMII statistics counters. Let's expose them to
ethtool. To interpret the counters correctly one has to be aware that
rx on SGMII side is tx on ethernet side. The counters are populated
by the chip in 100Mbps/1Gbps mode only.
v2:
- add constant AQR107_SGMII_STAT_SZ
- add struct aqr107_priv to be prepared for more private data fields
- let aqr107_get_stat() return U64_MAX in case of an error
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add suspend / resume callbacks for AQR107 family. Suspend powers down
the complete chip except MDIO and internal CPU.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The AQCS109 supports a proprietary 2-pair 1Gbps mode. The standard
registers don't allow to tell between 1000BaseT and 1000BaseT2.
Add reporting this proprietary mode based on a vendor register.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add reporting firmware details. These details are available only once
the firmware has finished initializing the chip. This can take some
time and we need to poll for init completion.
v2:
- Propagate timeout in aqr107_wait_reset_complete(). Don't bail out
completely on timeout because chip may be functional even w/o
firmware image.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If both link partners are Aquantia PHY's then additional information is
exchanged as part of the auto-negotiation. Report remote capabilities
if link partner is Aquantia PHY.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Aquantia PHY's of the AQR107 family support the downshift feature.
Add support for it as standard PHY tunable so that it can be controlled
via ethtool.
The AQCS109 supports a proprietary 2-pair 1Gbps mode. If two such PHY's
are connected to each other with a 2-pair cable, they may not be able
to establish a link if both advertise modes > 1Gbps.
v2:
- add downshift event detection
- warn if downshift occurred
- read downshifted rate from vendor register
- enable downshift per default on all AQR107 family members
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Depending on the auto-negotiated speed the PHY may change the interface
mode. Check for new mode and set phydev->interface accordingly.
Signed-off-by: Nikita Yushchenko <nikita.yoush@cogentembedded.com>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
[hkallweit1@gmail.com: picked from bigger patch and reworked]
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Let config_init check for unsupported interface modes on AQR107/AQCS109.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
[hkallweit1@gmail.com: adjusted for AQR107/AQCS109 specifics]
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This adds HWMON support for the temperature sensor and the related
alarms on the 107/108/109 chips. This patch is based on work from
Nikita and Andrew. I added:
- support for changing alarm thresholds via sysfs
- move HWMON code to a separate source file to improve maintainability
- smaller changes like using IS_REACHABLE instead of ifdef
(avoids problems if PHY driver is built in and HWMON is a module)
v2:
- remove struct aqr_priv
- rename header file to aquantia.h
v3:
- add conditional compiling of aquantia_hwmon.c
- improve converting sensor register values to/from long
- add helper aqr_hwmon_test_bit
Signed-off-by: Nikita Yushchenko <nikita.yoush@cogentembedded.com>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Rename aquantia.c to aquantia_main.c to be prepared for adding new
functionality to separate source code files.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jianping Liu