IVB introduced the CUR_FBC_CTL register which allows reducing the cursor
height down to 8 lines from the otherwise square cursor dimensions.
Implement support for it. CUR_FBC_CTL can't be used when the cursor
is rotated.
Commandeer the otherwise unused cursor->cursor.size to track the
current value of CUR_FBC_CTL to optimize away redundant CUR_FBC_CTL
writes, and to notice when we need to arm the update via CURBASE if
just CUR_FBC_CTL changes.
v2: Reverse the gen check to make it sane
v3: Only enable CUR_FBC_CTL when cursor is enabled, adapt to
earlier code changes which means we now actually turn off
the cursor when we're supposed to unlike v2
v4: Add a comment about rotation vs. CUR_FBC_CTL,
rebase due to 'dirty' (Chris)
v5: Rebase to the atomic world
Handle 180 degree rotation
Add HAS_CUR_FBC()
v6: Rebase
v7: Rebase due to I915_WRITE_FW/uncore.lock
s/size/fbc_ctl/
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170327185546.2977-12-ville.syrjala@linux.intel.com
Reviewed-by: Imre Deak <imre.deak@intel.com>
Implement proper two stage watermark programming for g4x. As with
other pre-SKL platforms, the watermark registers aren't double
buffered on g4x. Hence we must sequence the watermark update
carefully around plane updates.
The code is quite heavily modelled on the VLV/CHV code, with some
fairly significant differences due to the different hardware
architecture:
* g4x doesn't use inverted watermark values
* CxSR actually affects the watermarks since it controls memory self
refresh in addition to the max FIFO mode
* A further HPLL SR mode is possible with higher memory wakeup
latency
* g4x has FBC2 and so it also has FBC watermarks
* max FIFO mode for primary plane only (cursor is allowed, sprite is not)
* g4x has no manual FIFO repartitioning
* some TLB miss related workarounds are needed for the watermarks
Actually the hardware is quite similar to ILK+ in many ways. The
most visible differences are in the actual watermakr register
layout. ILK revamped that part quite heavily whereas g4x is still
using the layout inherited from earlier platforms.
Note that we didn't previously enable the HPLL SR on g4x. So in order
to not introduce too many functional changes in this patch I've not
actually enabled it here either, even though the code is now fully
ready for it. We'll enable it separately later on.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170421181432.15216-13-ville.syrjala@linux.intel.com
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
In order to allow use of e.g. forcewake_domains in a other feature headers
included from the top of i915_drv.h, move all uncore related definitions
into their own header.
v2: move __mask_next_bit macro to utils header (Mika)
Signed-off-by: Michal Wajdeczko <michal.wajdeczko@intel.com>
Suggested-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Cc: Mika Kuoppala <mika.kuoppala@intel.com>
Reviewed-by: Mika Kuoppala <mika.kuoppala@intel.com>
Signed-off-by: Mika Kuoppala <mika.kuoppala@intel.com>
Shuffle the arguments to intel_lpe_audio_notify() around a bit. Pipe
and port being the most important things, so let's put the first, and
thre rest can come in as is. Also constify the eld argument.
Cc: Takashi Iwai <tiwai@suse.de>
Cc: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170427160231.13337-8-ville.syrjala@linux.intel.com
Reviewed-by: Takashi Iwai <tiwai@suse.de>
There's no need to distinguish between the DP link rate and HDMI TMDS
clock for the purposes of the LPE audio. Both are actually the same
thing more or less, which is the link symbol clock. So let's just
call the thing ls_clock and simplify the code.
Cc: Takashi Iwai <tiwai@suse.de>
Cc: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170427160231.13337-6-ville.syrjala@linux.intel.com
Reviewed-by: Takashi Iwai <tiwai@suse.de>
2 clflushes on two different objects are not ordered, and so do not
belong to the same timeline (context). Either we use a unique context
for each, or we reserve a special global context to mean unordered.
Ideally, we would reserve 0 to mean unordered (DMA_FENCE_NO_CONTEXT) to
have the same semantics everywhere.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Reviewed-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170503093924.5320-1-chris@chris-wilson.co.uk
Add intel_irq_fini() for placing the deinitialization code,
starting with freeing dev_priv->l3_parity.remap_info[].
Signed-off-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Cc: Mika Kuoppala <mika.kuoppala@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: http://patchwork.freedesktop.org/patch/msgid/1493366319-18515-1-git-send-email-joonas.lahtinen@linux.intel.com
HAS_HW_CONTEXTS is misleading condition for GPU reset and CCID,
replace it with Gen specific (to be updated in next patches).
HAS_HW_CONTEXTS in i915_l3_write is bogus because each HAS_L3_DPF
match also has .has_hw_contexts = 1 set.
This leads to us being able to get rid of the property completely.
v2:
- Keep the checks at Gen6 for no functional change (Ville)
Signed-off-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Cc: Mika Kuoppala <mika.kuoppala@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Pre-calculate engine context size based on engine class and device
generation and store it in the engine instance.
v2:
- Squash and get rid of hw_context_size (Chris)
v3:
- Move after MMIO init for probing on Gen7 and 8 (Chris)
- Retained rounding (Tvrtko)
v4:
- Rebase for deferred legacy context allocation
Signed-off-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Cc: Paulo Zanoni <paulo.r.zanoni@intel.com>
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Daniele Ceraolo Spurio <daniele.ceraolospurio@intel.com>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Cc: Oscar Mateo <oscar.mateo@intel.com>
Cc: Zhenyu Wang <zhenyuw@linux.intel.com>
Cc: intel-gvt-dev@lists.freedesktop.org
Acked-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Introduce a new execobject.flag (EXEC_OBJECT_CAPTURE) that userspace may
use to indicate that it wants the contents of this buffer preserved in
the error state (/sys/class/drm/cardN/error) following a GPU hang
involving this batch.
Use this at your discretion, the contents of the error state. although
compressed, are allocated with GFP_ATOMIC (i.e. limited) and kept for all
eternity (until the error state is destroyed).
Based on an earlier patch by Ben Widawsky <ben@bwidawsk.net>
Testcase: igt/gem_exec_capture
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Ben Widawsky <ben@bwidawsk.net>
Cc: Matt Turner <mattst88@gmail.com>
Acked-by: Ben Widawsky <ben@bwidawsk.net>
Acked-by: Matt Turner <mattst88@gmail.com>
Reviewed-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170415093902.22581-1-chris@chris-wilson.co.uk
When discussing a new WC mmap, we based the interface upon the
assumption that GTT was fully coherent. How naive! Commits 3b5724d702
("drm/i915: Wait for writes through the GTT to land before reading
back") and ed4596ea99 ("drm/i915/guc: WA to address the Ringbuffer
coherency issue") demonstrate that writes through the GTT are indeed
delayed and may be overtaken by direct WC access. To be safe, if
userspace is mixing WC mmaps with other potential GTT access (pwrite,
GTT mmaps) it should use set_domain(WC).
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=96563
Testcase: igt/gem_pwrite/small-gtt*
Testcase: igt/drv_selftest/coherency
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170412110111.26626-2-chris@chris-wilson.co.uk
These params are passed by value, const qualifiers are ignored any way.
While around, unify timeout_ms type from long to int.
Signed-off-by: Michal Wajdeczko <michal.wajdeczko@intel.com>
Suggested-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Link: http://patchwork.freedesktop.org/patch/msgid/20170410093817.151280-1-michal.wajdeczko@intel.com
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
In some cases we may want to spend more time in atomic wait than
hardcoded 2us. Let's add additional fast timeout parameter to allow
flexible configuration of atomic timeout before switching into heavy wait.
Add also possibility to return registry value to avoid extra read.
v2: use explicit fast timeout (Tvrtko/Chris)
allow returning register value (Chris)
Signed-off-by: Michal Wajdeczko <michal.wajdeczko@intel.com>
Suggested-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Link: http://patchwork.freedesktop.org/patch/msgid/20170407160145.181328-1-michal.wajdeczko@intel.com
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
There is no need to specify timeout as unsigned long since this parameter
will be consumed by usecs_to_jiffies() which expects unsigned int only.
Signed-off-by: Michal Wajdeczko <michal.wajdeczko@intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170407133212.174608-1-michal.wajdeczko@intel.com
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
By using the same structure for both interruptible and
uninterruptible locking in shrinker code, combined with the
information that mm.interruptible is only being written to, the
code can be greatly simplified.
Also removing the i915_gem_ prefix from the locking functions so
that nobody in their wildest dreams considers exporting them.
Signed-off-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: http://patchwork.freedesktop.org/patch/msgid/1491562175-27680-1-git-send-email-joonas.lahtinen@linux.intel.com
We can't sometimes use these macros in other headers due to
include and definition order. As i915_utils.h already contains
other helper macros move these macros there.
v2: checkpatch cleanup for WARN() macro.
Signed-off-by: Michal Wajdeczko <michal.wajdeczko@intel.com>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Link: http://patchwork.freedesktop.org/patch/msgid/20170328084513.174200-1-michal.wajdeczko@intel.com
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Old devices have quite severe restrictions for using fences, and unlike
more recent device (anything from Pineview onwards) we need to enforce
those restrictions even for unfenced tiled access from the render
pipeline.
Fixes: 944397f04f ("drm/i915: Store required fence size/alignment for GGTT vma")
Reported-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Cc: <drm-intel-fixes@lists.freedesktop.org> # v4.11-rc1+
Link: http://patchwork.freedesktop.org/patch/msgid/20170325113243.16438-1-chris@chris-wilson.co.uk
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Reviewed-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Tested-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
We can relax the requirement upon ourselves that the forcewake is
released immediately and just allow it to occur naturally following our
mmio request.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170323101944.21627-5-chris@chris-wilson.co.uk
Use find-first-set bitop to quickly scan through the fw_domains mask and
skip iterating over unused domains.
v2: Move the WARN into the caller, to prevent compiler warnings in
normal builds.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Mika Kuoppala <mika.kuoppala@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170323101944.21627-4-chris@chris-wilson.co.uk
Pass along the drm_i915_private pointer from the caller, rather than
looking it up from each fw_domain during fw_domains_get/_put. This
allows us to then eliminate the backpointer, in exchange for a more
complicated unwrapping procedure in the rare
intel_uncore_fw_release_timer().
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170323101944.21627-1-chris@chris-wilson.co.uk
When we wedge the device, we override engine->submit_request with a nop
to ensure that all in-flight requests are marked in error. However, igt
would like to unwedge the device to test -EIO handling. This requires us
to flush those in-flight requests and restore the original
engine->submit_request.
v2: Use a vfunc to unify enabling request submission to engines
v3: Split new vfunc to a separate patch.
v4: Make the wait interruptible -- the third party fences we wait upon
may be indefinitely broken, so allow the reset to be aborted.
Fixes: 821ed7df6e ("drm/i915: Update reset path to fix incomplete requests")
Testcase: igt/gem_eio
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Cc: Mika Kuoppala <mika.kuoppala@intel.com>
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com> #v3
Link: http://patchwork.freedesktop.org/patch/msgid/20170316171305.12972-3-chris@chris-wilson.co.uk
I915_RESET_IN_PROGRESS is being used for both signaling the requirement
to i915_mutex_lock_interruptible() to avoid taking the struct_mutex and
to instruct a waiter (already holding the struct_mutex) to perform the
reset. To allow for a little more coordination, split these two meaning
into a couple of distinct flags. I915_RESET_BACKOFF tells
i915_mutex_lock_interruptible() not to acquire the mutex and
I915_RESET_HANDOFF tells the waiter to call i915_reset().
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Acked-by: Michel Thierry <michel.thierry@intel.com>
Reviewed-by: Mika Kuoppala <mika.kuoppala@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170316171305.12972-1-chris@chris-wilson.co.uk
We have used cz timestamp register to gain a reference time wrt
to residency calculations. The residency counts are in cz clk ticks
(333Mhz clock) but for some reason the cz timestamp register gives
100us units. Perhaps for some other usage, the base-ten based values
are easier, but in residency calculations raw units would have been
the easiest.
As there is not much advantage of using base-ten clock through
a more costly punit access, take our reference times directly from
kernel clock.
v2: use ktime (Chris, Ville)
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Mika Kuoppala <mika.kuoppala@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Change the granularity from milliseconds to microseconds
when returning rc6 residencies. This is in preparation
for increased resolution on some platforms.
v2: use 64bit div macro (Chris)
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Mika Kuoppala <mika.kuoppala@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Plan is to make generic residency calculation utility
function for usage outside of sysfs. As a first step
move residency calculation into intel_pm.c
Signed-off-by: Mika Kuoppala <mika.kuoppala@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Used to obtain "dev_priv" from huc struct pointer.
We already have similar thing for guc.
Cc: Michal Wajdeczko <michal.wajdeczko@intel.com>
Signed-off-by: Arkadiusz Hiler <arkadiusz.hiler@intel.com>
Reviewed-by: Michal Wajdeczko <michal.wajdeczko@intel.com>
Signed-off-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Use I915_{READ,WRITE}_FW() for updating the DSPARB registers on
VLV/CHV. This is less expesive as we can grab the uncore.lock across
the entire sequence of reads and writes instead of each register
access grabbing it.
This also allows us to eliminate the dsparb lock entirely as the
uncore.lock now effectively protects the contents of the DSPARB
registers.
v2: Add a note that interrupts are already disabled (Chris)
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170309154434.29303-6-ville.syrjala@linux.intel.com
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
If the object is coherent, we can simply update the cache domain on the
whole object rather than calculate the before/after clflushes. The
advantage is that we then get correct tracking of ellided flushes when
changing coherency later.
Testcase: igt/gem_pwrite_snooped
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170310000942.11661-1-chris@chris-wilson.co.uk
Reviewed-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
We don't use the error return for anything other than reporting and
logging that there is no VBT. We can pull the logging in the function,
and remove the error status return. Moreover, if we needed the
information for something later on, we'd probably be better off storing
the bit in dev_priv, and using it where it's needed, instead of using
the error return.
While at it, improve the comments.
Cc: Manasi Navare <manasi.d.navare@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/438ebbb0d5f0d321c625065b9cc78532a1dab24f.1489152288.git.jani.nikula@intel.com
Baytrail PMIC vs. PMU race fixes from Hans de Goede
This time the right version (v4), with the compile fix.
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
"pm_intr_keep" is not conveying the intent that it is bitmask
of interrupts that must be zero(mbz) in GEN6_PMINTRMSK.
Name it "pm_intrmsk_mbz".
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Radoslaw Szwichtenberg <radoslaw.szwichtenberg@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Sagar Arun Kamble <sagar.a.kamble@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1489199821-6707-2-git-send-email-sagar.a.kamble@intel.com
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
On Baytrail, we manually calculate busyness over the evaluation interval
to avoid issues with miscaluations with RC6 enabled. However, it turns
out that the DOWN_EI interrupt generator is completely bust - it
operates in two modes, continuous or never. Neither of which are
conducive to good behaviour. Stop unmask the DOWN_EI interrupt and just
compute everything from the UP_EI which does seem to correspond to the
desired interval.
v2: Fixup gen6_rps_pm_mask() as well
v3: Inline vlv_c0_above() to combine the now identical elapsed
calculation for up/down and simplify the threshold testing
Fixes: 43cf3bf084 ("drm/i915: Improved w/a for rps on Baytrail")
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Cc: <stable@vger.kernel.org> # v4.1+
Link: http://patchwork.freedesktop.org/patch/msgid/20170309211232.28878-1-chris@chris-wilson.co.uk
Reviewed-by: Mika Kuoppala <mika.kuoppala@linux.intel.com>
This gets rid of the last users of for_each_intel_connector(), remove
that too.
At first I wasn't sure whether the 2 loops in the modeset state
checker should instead only loop over the connectors in the atomic
commit. But we never add connectors to an atomic update if they don't
(or won't have) a CRTC assigned, which means there'd be a gap in check
coverage. Hence loop over everything on those too.
v2: Rebase onto the iter_get/put->iter_begin/end rename.
Cc: Thierry Reding <thierry.reding@gmail.com>
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170301095226.30584-5-daniel.vetter@ffwll.ch
While at it also try to reduce the locking a bit to what's really just
needed instead of everything that we could possibly lock.
Added a new for_each_intel_connector_iter which includes the cast to
intel_connector.
Otherwise just plain transformation with nothing special going on.
v2: Review from Maarten:
- Stick with modeset_lock_all in sink_crc, it looks at crtc->state.
- Fix up early loop exit in i915_displayport_test_active_write.
v3: Rebase onto the iter_get/put->iter_begin/end rename.
Cc: Thierry Reding <thierry.reding@gmail.com>
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com> (v2)
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170301095226.30584-1-daniel.vetter@ffwll.ch
Backmerge drm-next to get at all the good stuff in drm-misc. We need
that because:
- drm_connector_list_iter conversion for i915 needs the core patches.
- Maarten's patches to use the new atomic state iterators also need
the core patches.
- We need the new link status property to complete the DP retraining
work, merging through 2 branches wasn't a good idea and we had to
partially backtrack.
- Chris needs reservation_object_trylock and we want to roll out
kref_read everywhere.
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
4 weeks worth of stuff since I was traveling&lazy:
- lspcon improvements (Imre)
- proper atomic state for cdclk handling (Ville)
- gpu reset improvements (Chris)
- lots and lots of polish around fences, requests, waiting and
everything related all over (both gem and modeset code), from Chris
- atomic by default on gen5+ minus byt/bsw (Maarten did the patch to
flip the default, really this is a massive joint team effort)
- moar power domains, now 64bit (Ander)
- big pile of in-kernel unit tests for various gem subsystems (Chris),
including simple mock objects for i915 device and and the ggtt
manager.
- i915_gpu_info in debugfs, for taking a snapshot of the current gpu
state. Same thing as i915_error_state, but useful if the kernel didn't
notice something is stick. From Chris.
- bxt dsi fixes (Umar Shankar)
- bxt w/a updates (Jani)
- no more struct_mutex for gem object unreference (Chris)
- some execlist refactoring (Tvrtko)
- color manager support for glk (Ander)
- improve the power-well sync code to better take over from the
firmware (Imre)
- gem tracepoint polish (Tvrtko)
- lots of glk fixes all around (Ander)
- ctx switch improvements (Chris)
- glk dsi support&fixes (Deepak M)
- dsi fixes for vlv and clanups, lots of them (Hans de Goede)
- switch to i915.ko types in lots of our internal modeset code (Ander)
- byt/bsw atomic wm update code, yay (Ville)
* tag 'drm-intel-next-2017-03-06' of git://anongit.freedesktop.org/git/drm-intel: (432 commits)
drm/i915: Update DRIVER_DATE to 20170306
drm/i915: Don't use enums for hardware engine id
drm/i915: Split breadcrumbs spinlock into two
drm/i915: Refactor wakeup of the next breadcrumb waiter
drm/i915: Take reference for signaling the request from hardirq
drm/i915: Add FIFO underrun tracepoints
drm/i915: Add cxsr toggle tracepoint
drm/i915: Add VLV/CHV watermark/FIFO programming tracepoints
drm/i915: Add plane update/disable tracepoints
drm/i915: Kill level 0 wm hack for VLV/CHV
drm/i915: Workaround VLV/CHV sprite1->sprite0 enable underrun
drm/i915: Sanitize VLV/CHV watermarks properly
drm/i915: Only use update_wm_{pre,post} for pre-ilk platforms
drm/i915: Nuke crtc->wm.cxsr_allowed
drm/i915: Compute proper intermediate wms for vlv/cvh
drm/i915: Skip useless watermark/FIFO related work on VLV/CHV when not needed
drm/i915: Compute vlv/chv wms the atomic way
drm/i915: Compute VLV/CHV FIFO sizes based on the PM2 watermarks
drm/i915: Plop vlv/chv fifo sizes into crtc state
drm/i915: Plop vlv wm state into crtc_state
...
It is always called from thread context.
Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
First slice of drm-misc-next for 4.12:
Core/subsystem-wide:
- link status core patch from Manasi, for signalling link train fail
to userspace. I also had the i915 patch in here, but that had a
small buglet in our CI, so reverted.
- more debugfs_remove removal from Noralf, almost there now (Noralf
said he'll try to follow up with the stragglers).
- drm todo moved into kerneldoc, for better visibility (see
Documentation/gpu/todo.rst), lots of starter tasks in there.
- devm_ of helpers + use it in sti (from Ben Gaignard, acked by Rob
Herring)
- extended framebuffer fbdev support (for fbdev flipping), and vblank
wait ioctl fbdev support (Maxime Ripard)
- misc small things all over, as usual
- add vblank callbacks to drm_crtc_funcs, plus make lots of good use
of this to simplify drivers (Shawn Guo)
- new atomic iterator macros to unconfuse old vs. new state
Small drivers:
- vc4 improvements from Eric
- vc4 kerneldocs (Eric)!
- tons of improvements for dw-mipi-dsi in rockchip from John Keeping
and Chris Zhong.
- MAINTAINERS entries for drivers managed in drm-misc. It's not yet
official, still an experiment, but definitely not complete fail and
better to avoid confusion. We kinda screwed that up with drm-misc a
bit when we started committers last year.
- qxl atomic conversion (Gabriel Krisman)
- bunch of virtual driver polish (qxl, virgl, ...)
- misc tiny patches all over
This is the first time we've done the same merge-window blackout for
drm-misc as we've done for drm-intel for ages, hence why we have a
_lot_ of stuff queued already. But it's still only half of drm-intel
(room to grow!), and the drivers in drm-misc experiment seems to work
at least insofar as that you also get lots of driver updates here
alredy.
* tag 'drm-misc-next-2017-03-06' of git://anongit.freedesktop.org/git/drm-misc: (141 commits)
drm/vc4: Fix OOPSes from trying to cache a partially constructed BO.
drm/vc4: Fulfill user BO creation requests from the kernel BO cache.
Revert "drm/i915: Implement Link Rate fallback on Link training failure"
drm/fb-helper: implement ioctl FBIO_WAITFORVSYNC
drm: Update drm_fbdev_cma_init documentation
drm/rockchip/dsi: add dw-mipi power domain support
drm/rockchip/dsi: fix insufficient bandwidth of some panel
dt-bindings: add power domain node for dw-mipi-rockchip
drm/rockchip/dsi: remove mode_valid function
drm/rockchip/dsi: dw-mipi: correct the coding style
drm/rockchip/dsi: dw-mipi: support RK3399 mipi dsi
dt-bindings: add rk3399 support for dw-mipi-rockchip
drm/rockchip: dw-mipi-dsi: add reset control
drm/rockchip: dw-mipi-dsi: support non-burst modes
drm/rockchip: dw-mipi-dsi: defer probe if panel is not loaded
drm/rockchip: vop: test for P{H,V}SYNC
drm/rockchip: dw-mipi-dsi: use positive check for N{H, V}SYNC
drm/rockchip: dw-mipi-dsi: use specific poll helper
drm/rockchip: dw-mipi-dsi: improve PLL configuration
drm/rockchip: dw-mipi-dsi: properly configure PHY timing
...
As we now take the breadcrumbs spinlock within the interrupt handler, we
wish to minimise its hold time. During the interrupt we do not care
about the state of the full rbtree, only that of the first element, so
we can guard that with a separate lock.
v2: Rename first_wait to irq_wait to make it clearer that it is guarded
by irq_lock.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Mika Kuoppala <mika.kuoppala@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170303190824.1330-1-chris@chris-wilson.co.uk
Start computing the vlv/chv watermarks the atomic way, from the
.compute_pipe_wm() hook. We'll recompute the actual watermarks
for only planes that are part of the state, the other planes will
keep their watermark from the last time it was computed.
And the actual watermark programming will happen from the
.initial_watermarks() hook. For now we'll just compute the
optimal watermarks, and we'll hook up the intermediate
watermarks properly later.
The DSPARB registers responsible for the FIFO paritioning are
double buffered, so they will be programming from
intel_begin_crtc_commit().
v2: s/noninverted/raw/ for consistency with other platforms
s/vlv_plane_wm_set/vlv_raw_plane_wm_set/ for clarity
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170302171508.1666-8-ville.syrjala@linux.intel.com
It is preferred to pass pipe_config to functions instead of accessing
crtc->config directly. Follow suit and pass pipe_config to the fdi link
train functions.
v2: Add const; s/pipe_config/crtc_state/ (Ville)
Signed-off-by: Ander Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170302125857.14665-5-ander.conselvan.de.oliveira@intel.com
Ville Syrjälä