Recent versions of the PCI Express specification have deprecated support
for I/O transactions and actually some PCIe host bridges, such as Power
Systems Host Bridge 4 (PHB4), do not implement them. Conversely a DEFEA
adapter can have its MMIO decoding disabled with ECU (EISA Configuration
Utility) and therefore not available for us with the resource allocation
infrastructure we implement.
However either I/O address space will always be available for use with
the DEFEA (EISA) and DEFPA (PCI) adapters and both have double address
decoding implemented in hardware for Control and Status Register access.
The two kinds of adapters can be present both at once in a single mixed
PCI/EISA system. For the DEFTA (TURBOchannel) variant there is no issue
as there has been no port I/O address space defined for that bus.
To make people's life easier and the driver more robust remove the
DEFXX_MMIO configuration option so as to rather than making the choice
for the I/O address space to use at build time for all the adapters
installed in the system let the driver choose the most suitable address
space dynamically on a case-by-case basis at run time. Make MMIO the
default and resort to port I/O should the default fail for some reason.
This way multiple adapters installed in one system can use different I/O
address spaces each, in particular in the presence of DEFEA adapters in
a pure-EISA or a mixed EISA/PCI system (it is expected that DEFPA boards
will use MMIO in normal circumstances).
The choice of the I/O address space to use continues being reported by
the driver on startup, e.g.:
eisa 00:05: EISA: slot 5: DEC3002 detected
defxx: v1.12 2021/03/10 Lawrence V. Stefani and others
00:05: DEFEA at I/O addr = 0x5000, IRQ = 10, Hardware addr = 00-00-f8-c8-b3-b6
00:05: registered as fddi0
and:
defxx: v1.12 2021/03/10 Lawrence V. Stefani and others
0031:02:04.0: DEFPA at MMIO addr = 0x620c080020000, IRQ = 57, Hardware addr = 00-60-6d-93-91-98
0031:02:04.0: registered as fddi0
and:
defxx: v1.12 2021/03/10 Lawrence V. Stefani and others
tc2: DEFTA at MMIO addr = 0x1f100000, IRQ = 21, Hardware addr = 08-00-2b-b0-8b-1e
tc2: registered as fddi0
so there is no need to add further information.
The change is supposed to cause a negligible performance hit as I/O
accessors will now have code executed conditionally at run time.
Signed-off-by: Maciej W. Rozycki <macro@orcam.me.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Following the recent update to MAINTAINERS update my e-mail address.
Signed-off-by: Maciej W. Rozycki <macro@orcam.me.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Reserve DEFEA resources according to actual use. There are three
regions, for the ESIC ASIC's CSRs, for the discrete Burst Holdoff
register, and for the PDQ ASIC's CSRs. The latter is mapped in the
memory or port I/O address space depending on configuration. The two
formers are hardwired and always mapped in the port I/O address space.
Signed-off-by: Maciej W. Rozycki <macro@linux-mips.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use ESIC's memory area 1 (MEMCS1) and its Memory Address High Compare
and Memory Address Low Compare registers to set up the MMIO range for
decoding accesses to PDQ ASIC registers. Previously the PDQ ASIC was
thought to be addressable with the memory area 0 (MEMCS0) and its Memory
Address Compare and Memory Address Mask registers.
The MMIO range allocated for the option card is preset via ECU (EISA
Configuration Utility) and can be disabled, so handle such a case
gracefully too.
Signed-off-by: Maciej W. Rozycki <macro@linux-mips.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the slot-specific I/O range for decoding accesses to PDQ ASIC
registers (IOCS0) and the discrete Burst Holdoff register (IOCS1) as per
the "HD64981F EISA Slave Interface Controller (ESIC)" datasheet. Use
disjoint decode ranges now that the assignment of chip selects is known.
Update the span of the port I/O resource requested accordingly.
Signed-off-by: Maciej W. Rozycki <macro@linux-mips.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This fixes issues with debug printk calls across the driver, normally
disabled; first compilation errors:
drivers/net/fddi/defxx.c:676:1: error: pasting "(" and ""In dfx_bus_init...\n"" does not give a valid preprocessing token
drivers/net/fddi/defxx.c:820:1: error: pasting "(" and ""In dfx_bus_uninit...\n"" does not give a valid preprocessing token
and so on, and then warnings:
drivers/net/fddi/defxx.c: In function 'dfx_driver_init':
drivers/net/fddi/defxx.c:1132: warning: format '%0X' expects type 'unsigned int', but argument 4 has type 'dma_addr_t'
drivers/net/fddi/defxx.c:1132: warning: format '%0X' expects type 'unsigned int', but argument 4 has type 'dma_addr_t'
etc. Additionally casts are removed from virtual addresses and %p used.
Signed-off-by: Maciej W. Rozycki <macro@linux-mips.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move the FDDI drivers into drivers/net/fddi/ and make the
necessary Kconfig and Makefile changes.
CC: "Maciej W. Rozycki" <macro@linux-mips.org>
CC: Christoph Goos <cgoos@syskonnect.de>
CC: <linux@syskonnect.de>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Maciej W. Rozycki