Pull SCSI target updates from Nicholas Bellinger:
"The highlights this round include:
- Introduce configfs support for unlocked configfs_depend_item()
(krzysztof + andrezej)
- Conversion of usb-gadget target driver to new function registration
interface (andrzej + sebastian)
- Enable qla2xxx FC target mode support for Extended Logins (himansu +
giridhar)
- Enable qla2xxx FC target mode support for Exchange Offload (himansu +
giridhar)
- Add qla2xxx FC target mode irq affinity notification + selective
command queuing. (quinn + himanshu)
- Fix iscsi-target deadlock in se_node_acl configfs deletion (sagi +
nab)
- Convert se_node_acl configfs deletion + se_node_acl->queue_depth to
proper se_session->sess_kref + target_get_session() usage. (hch +
sagi + nab)
- Fix long-standing race between se_node_acl->acl_kref get and
get_initiator_node_acl() lookup. (hch + nab)
- Fix target/user block-size handling, and make sure netlink reaches
all network namespaces (sheng + andy)
Note there is an outstanding bug-fix series for remote I_T nexus port
TMR LUN_RESET has been posted and still being tested, and will likely
become post -rc1 material at this point"
* 'for-next' of git://git.kernel.org/pub/scm/linux/kernel/git/nab/target-pending: (56 commits)
scsi: qla2xxxx: avoid type mismatch in comparison
target/user: Make sure netlink would reach all network namespaces
target: Obtain se_node_acl->acl_kref during get_initiator_node_acl
target: Convert ACL change queue_depth se_session reference usage
iscsi-target: Fix potential dead-lock during node acl delete
ib_srpt: Convert acl lookup to modern get_initiator_node_acl usage
tcm_fc: Convert acl lookup to modern get_initiator_node_acl usage
tcm_fc: Wait for command completion before freeing a session
target: Fix a memory leak in target_dev_lba_map_store()
target: Support aborting tasks with a 64-bit tag
usb/gadget: Remove set-but-not-used variables
target: Remove an unused variable
target: Fix indentation in target_core_configfs.c
target/user: Allow user to set block size before enabling device
iser-target: Fix non negative ERR_PTR isert_device_get usage
target/fcoe: Add tag support to tcm_fc
qla2xxx: Check for online flag instead of active reset when transmitting responses
qla2xxx: Set all queues to 4k
qla2xxx: Disable ZIO at start time.
qla2xxx: Move atioq to a different lock to reduce lock contention
...
This patch addresses a long standing race where obtaining
se_node_acl->acl_kref in __transport_register_session()
happens a bit too late, and leaves open the potential
for core_tpg_del_initiator_node_acl() to hit a NULL
pointer dereference.
Instead, take ->acl_kref in core_tpg_get_initiator_node_acl()
while se_portal_group->acl_node_mutex is held, and move the
final target_put_nacl() from transport_deregister_session()
into transport_free_session() so that fabric driver login
failure handling using the modern method to still work
as expected.
Also, update core_tpg_get_initiator_node_acl() to take
an extra reference for dynamically generated acls for
demo-mode, before returning to fabric caller. Also
update iscsi-target sendtargets special case handling
to use target_tpg_has_node_acl() when checking if
demo_mode_discovery == true during discovery lookup.
Note the existing wait_for_completion(&acl->acl_free_comp)
in core_tpg_del_initiator_node_acl() does not change.
Cc: Sagi Grimberg <sagig@mellanox.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Hannes Reinecke <hare@suse.de>
Cc: Andy Grover <agrover@redhat.com>
Cc: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This patch converts core_tpg_set_initiator_node_queue_depth()
to use struct se_node_acl->acl_sess_list when performing
explicit se_tpg_tfo->shutdown_session() for active sessions,
in order for new se_node_acl->queue_depth to take effect.
This follows how core_tpg_del_initiator_node_acl() currently
works when invoking se_tpg_tfo->shutdown-session(), and ahead
of the next patch to take se_node_acl->acl_kref during lookup,
the extra get_initiator_node_acl() can go away. In order to
achieve this, go ahead and change target_get_session() to use
kref_get_unless_zero() and propigate up the return value
to know when a session is already being released.
This is because se_node_acl->acl_group is already protecting
se_node_acl->acl_group reference via configfs, and shutdown
within core_tpg_del_initiator_node_acl() won't occur until
sys_write() to core_tpg_set_initiator_node_queue_depth()
attribute returns back to user-space.
Also, drop the left-over iscsi-target hack, and obtain
se_portal_group->session_lock in lio_tpg_shutdown_session()
internally. Remove iscsi-target wrapper and unused se_tpg +
force parameters and associated code.
Reported-by: Christoph Hellwig <hch@lst.de>
Cc: Sagi Grimberg <sagig@mellanox.com>
Cc: Hannes Reinecke <hare@suse.de>
Cc: Andy Grover <agrover@redhat.com>
Cc: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Avoid truncating the tag argument of target_submit_tmr() to a
32-bit number if the caller passes a 64-bit number.
Signed-off-by: Bart Van Assche <bart.vanassche@sandisk.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Andy Grover <agrover@redhat.com>
Cc: Sagi Grimberg <sagig@mellanox.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
The num_node_acls member in struct se_portal_group is modified
by several functions but is never read. Hence remove it.
Signed-off-by: Bart Van Assche <bart.vanassche@sandisk.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Andy Grover <agrover@redhat.com>
Cc: Sagi Grimberg <sagig@mellanox.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
queue work element to specific process lessen cache miss
Signed-off-by: Quinn Tran <quinn.tran@qlogic.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@qlogic.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This patch addresses a race + use after free where the first
stage of COMPARE_AND_WRITE in compare_and_write_callback()
is rescheduled after the backend sends the secondary WRITE,
resulting in second stage compare_and_write_post() callback
completing in target_complete_ok_work() before the first
can return.
Because current code depends on checking se_cmd->se_cmd_flags
after return from se_cmd->transport_complete_callback(),
this results in first stage having SCF_COMPARE_AND_WRITE_POST
set, which incorrectly falls through into second stage CAW
processing code, eventually triggering a NULL pointer
dereference due to use after free.
To address this bug, pass in a new *post_ret parameter into
se_cmd->transport_complete_callback(), and depend upon this
value instead of ->se_cmd_flags to determine when to return
or fall through into ->queue_status() code for CAW.
Cc: Sagi Grimberg <sagig@mellanox.com>
Cc: <stable@vger.kernel.org> # v3.12+
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This does nothing, and there are many other places where
transport_cmd_check_stop_to_fabric()'s retval is not checked>, If we
wanted to check it here, we should probably do it those other places too.
Signed-off-by: Andy Grover <agrover@redhat.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This patch adds an optional fabric driver provided SGL limit
that target-core will honor as it's own internal I/O maximum
transfer length limit, as exposed by EVPD=0xb0 block limits
parameters.
This is required for handling cases when host I/O transfer
length exceeds the requested EVPD block limits maximum
transfer length. The initial user of this logic is qla2xxx,
so that we can avoid having to reject I/Os from some legacy
FC hosts where EVPD=0xb0 parameters are not honored.
When se_cmd payload length exceeds the provided limit in
target_check_max_data_sg_nents() code, se_cmd->data_length +
se_cmd->prot_length are reset with se_cmd->residual_count
plus underflow bit for outgoing TFO response callbacks.
It also checks for existing CDB level underflow + overflow
and recalculates final residual_count as necessary.
Note this patch currently assumes 1:1 mapping of PAGE_SIZE
per struct scatterlist entry.
Reported-by: Craig Watson <craig.watson@vanguard-rugged.com>
Cc: Craig Watson <craig.watson@vanguard-rugged.com>
Tested-by: Himanshu Madhani <himanshu.madhani@qlogic.com>
Cc: Roland Dreier <roland@purestorage.com>
Cc: Arun Easi <arun.easi@qlogic.com>
Cc: Giridhar Malavali <giridhar.malavali@qlogic.com>
Cc: Andrew Vasquez <andrew.vasquez@qlogic.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Hannes Reinecke <hare@suse.de>
Cc: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
For every command, we set se_ordered_id by doing atomic_inc_return on
dev->dev_ordered_id for the corresponding device. However, the only
places this value gets used are in pr_debug() calls, which doesn't
seem worth an extra atomic op per IO.
Signed-off-by: Roland Dreier <roland@purestorage.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Make the warning about unsupported SCSI opcode more useful:
- Add in the initiator name so we know who's sending it.
- Print the warning even for opcodes that spc_parse_cdb() knows about
but that we don't handle.
Signed-off-by: Joern Engel <joern@purestorage.com>
Signed-off-by: Spencer Baugh <sbaugh@catern.com>
Reviewed-by: Sagi Grimberg <sagig@mellanox.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
It's not necessarily a fatal error if a command with a data-out phase
has a data length that differs from the transport data length (e.g.
PERSISTENT RESERVE OUT might have a parameter list length in the CDB
that's smaller than the FC_DL field), so allow these commands. The
Windows compliance test sends them.
Signed-off-by: Roland Dreier <roland@purestorage.com>
Signed-off-by: Spencer Baugh <sbaugh@catern.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
In case a LU spans 64bit sectors, fixed size sense data information
field is only 32 bits which means the sector information will be truncated.
Thus, if the LU spans 64bit sectors, use descriptor format sense data to
correctly report sector information.
Reported-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sagi Grimberg <sagig@mellanox.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Make sure that the input sense buffer has sufficient length
to fit the information descriptor (12 additional bytes).
Modify scsi_set_sense_information to receive the sense buffer
length and adjust its callers scsi target and libata.
(Fix patch fuzz in scsi_set_sense_information - nab)
Reported-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Sagi Grimberg <sagig@mellanox.com>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Cc: Tejun Heo <tj@kernel.org>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
PI errors were reported with ILLEGAL_REQUEST sense key but
there was actually no problem with the request. Target
detected PI errors should be reported with aborted command
sense key.
Signed-off-by: Sagi Grimberg <sagig@mellanox.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Instead of open coding the sense buffer construction, use
scsi scsi_build_sense_buffer() and scsi_set_sense_information()
helpers which moved to scsi_common.
Signed-off-by: Sagi Grimberg <sagig@mellanox.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Move the code for translating a sense_reason_t code into a SCSI status
ASC and ASCQ codes from transport_send_check_condition_and_sense() into
the new function translate_sense_reason(). Convert the switch statement
that performs the translation into table-driven code.
Signed-off-by: Bart Van Assche <bart.vanassche@sandisk.com>
Signed-off-by: Sagi Grimberg <sagig@mellanox.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Inline this function in its call site since it performs a trivial
task and since it is only called once.
Signed-off-by: Bart Van Assche <bart.vanassche@sandisk.com>
Signed-off-by: Sagi Grimberg <sagig@mellanox.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Pull SCSI target updates from Nicholas Bellinger:
"It's been a busy development cycle for target-core in a number of
different areas.
The fabric API usage for se_node_acl allocation is now within
target-core code, dropping the external API callers for all fabric
drivers tree-wide.
There is a new conversion to RCU hlists for se_node_acl and
se_portal_group LUN mappings, that turns fast-past LUN lookup into a
completely lockless code-path. It also removes the original
hard-coded limitation of 256 LUNs per fabric endpoint.
The configfs attributes for backends can now be shared between core
and driver code, allowing existing drivers to use common code while
still allowing flexibility for new backend provided attributes.
The highlights include:
- Merge sbc_verify_dif_* into common code (sagi)
- Remove iscsi-target support for obsolete IFMarker/OFMarker
(Christophe Vu-Brugier)
- Add bidi support in target/user backend (ilias + vangelis + agover)
- Move se_node_acl allocation into target-core code (hch)
- Add crc_t10dif_update common helper (akinobu + mkp)
- Handle target-core odd SGL mapping for data transfer memory
(akinobu)
- Move transport ID handling into target-core (hch)
- Move task tag into struct se_cmd + support 64-bit tags (bart)
- Convert se_node_acl->device_list[] to RCU hlist (nab + hch +
paulmck)
- Convert se_portal_group->tpg_lun_list[] to RCU hlist (nab + hch +
paulmck)
- Simplify target backend driver registration (hch)
- Consolidate + simplify target backend attribute implementations
(hch + nab)
- Subsume se_port + t10_alua_tg_pt_gp_member into se_lun (hch)
- Drop lun_sep_lock for se_lun->lun_se_dev RCU usage (hch + nab)
- Drop unnecessary core_tpg_register TFO parameter (nab)
- Use 64-bit LUNs tree-wide (hannes)
- Drop left-over TARGET_MAX_LUNS_PER_TRANSPORT limit (hannes)"
* 'for-next' of git://git.kernel.org/pub/scm/linux/kernel/git/nab/target-pending: (76 commits)
target: Bump core version to v5.0
target: remove target_core_configfs.h
target: remove unused TARGET_CORE_CONFIG_ROOT define
target: consolidate version defines
target: implement WRITE_SAME with UNMAP bit using ->execute_unmap
target: simplify UNMAP handling
target: replace se_cmd->execute_rw with a protocol_data field
target/user: Fix inconsistent kmap_atomic/kunmap_atomic
target: Send UA when changing LUN inventory
target: Send UA upon LUN RESET tmr completion
target: Send UA on ALUA target port group change
target: Convert se_lun->lun_deve_lock to normal spinlock
target: use 'se_dev_entry' when allocating UAs
target: Remove 'ua_nacl' pointer from se_ua structure
target_core_alua: Correct UA handling when switching states
xen-scsiback: Fix compile warning for 64-bit LUN
target: Remove TARGET_MAX_LUNS_PER_TRANSPORT
target: use 64-bit LUNs
target: Drop duplicate + unused se_dev_check_wce
target: Drop unnecessary core_tpg_register TFO parameter
...
Use kvfree() instead of open-coding it.
Signed-off-by: Pekka Enberg <penberg@kernel.org>
Cc: "Nicholas A. Bellinger" <nab@linux-iscsi.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Pull networking updates from David Miller:
1) Add TX fast path in mac80211, from Johannes Berg.
2) Add TSO/GRO support to ibmveth, from Thomas Falcon
3) Move away from cached routes in ipv6, just like ipv4, from Martin
KaFai Lau.
4) Lots of new rhashtable tests, from Thomas Graf.
5) Run ingress qdisc lockless, from Alexei Starovoitov.
6) Allow servers to fetch TCP packet headers for SYN packets of new
connections, for fingerprinting. From Eric Dumazet.
7) Add mode parameter to pktgen, for testing receive. From Alexei
Starovoitov.
8) Cache access optimizations via simplifications of build_skb(), from
Alexander Duyck.
9) Move page frag allocator under mm/, also from Alexander.
10) Add xmit_more support to hv_netvsc, from KY Srinivasan.
11) Add a counter guard in case we try to perform endless reclassify
loops in the packet scheduler.
12) Extern flow dissector to be programmable and use it in new "Flower"
classifier. From Jiri Pirko.
13) AF_PACKET fanout rollover fixes, performance improvements, and new
statistics. From Willem de Bruijn.
14) Add netdev driver for GENEVE tunnels, from John W Linville.
15) Add ingress netfilter hooks and filtering, from Pablo Neira Ayuso.
16) Fix handling of epoll edge triggers in TCP, from Eric Dumazet.
17) Add an ECN retry fallback for the initial TCP handshake, from Daniel
Borkmann.
18) Add tail call support to BPF, from Alexei Starovoitov.
19) Add several pktgen helper scripts, from Jesper Dangaard Brouer.
20) Add zerocopy support to AF_UNIX, from Hannes Frederic Sowa.
21) Favor even port numbers for allocation to connect() requests, and
odd port numbers for bind(0), in an effort to help avoid
ip_local_port_range exhaustion. From Eric Dumazet.
22) Add Cavium ThunderX driver, from Sunil Goutham.
23) Allow bpf programs to access skb_iif and dev->ifindex SKB metadata,
from Alexei Starovoitov.
24) Add support for T6 chips in cxgb4vf driver, from Hariprasad Shenai.
25) Double TCP Small Queues default to 256K to accomodate situations
like the XEN driver and wireless aggregation. From Wei Liu.
26) Add more entropy inputs to flow dissector, from Tom Herbert.
27) Add CDG congestion control algorithm to TCP, from Kenneth Klette
Jonassen.
28) Convert ipset over to RCU locking, from Jozsef Kadlecsik.
29) Track and act upon link status of ipv4 route nexthops, from Andy
Gospodarek.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (1670 commits)
bridge: vlan: flush the dynamically learned entries on port vlan delete
bridge: multicast: add a comment to br_port_state_selection about blocking state
net: inet_diag: export IPV6_V6ONLY sockopt
stmmac: troubleshoot unexpected bits in des0 & des1
net: ipv4 sysctl option to ignore routes when nexthop link is down
net: track link-status of ipv4 nexthops
net: switchdev: ignore unsupported bridge flags
net: Cavium: Fix MAC address setting in shutdown state
drivers: net: xgene: fix for ACPI support without ACPI
ip: report the original address of ICMP messages
net/mlx5e: Prefetch skb data on RX
net/mlx5e: Pop cq outside mlx5e_get_cqe
net/mlx5e: Remove mlx5e_cq.sqrq back-pointer
net/mlx5e: Remove extra spaces
net/mlx5e: Avoid TX CQE generation if more xmit packets expected
net/mlx5e: Avoid redundant dev_kfree_skb() upon NOP completion
net/mlx5e: Remove re-assignment of wq type in mlx5e_enable_rq()
net/mlx5e: Use skb_shinfo(skb)->gso_segs rather than counting them
net/mlx5e: Static mapping of netdev priv resources to/from netdev TX queues
net/mlx4_en: Use HW counters for rx/tx bytes/packets in PF device
...
This is the usual grab bag of driver updates (lpfc, hpsa,
megaraid_sas, cxgbi, be2iscsi) plus an assortment of minor updates.
There are also one new driver: the Cisco snic; the advansys driver has
been rewritten to get rid of the warning about converting it to the
DMA API, the tape statistics patch got in and finally, there's a
resuffle of SCSI header files to separate more cleanly initiator from
target mode (and better share the common definitions).
Signed-off-by: James Bottomley <JBottomley@Odin.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iQEcBAABAgAGBQJViKWdAAoJEDeqqVYsXL0MAr8IAMmlA6HBVjMJJFCEOY9corHj
e70MNQa7LUgf+JCdOtzGcvHXTiFFd4IHZAwXUJAnsC4IU2QWEfi1bjUTErlqBIGk
LoZlXXpEHnFpmWot3OluOzzcGcxede8rVgPiKWVVdojIngBC2+LL/i2vPCJ84ri9
WCVlk6KBvWZXuU6JuOKAb2FO9HOX7Q61wuKAMast2Qc6RNc2ksgc7VbstsITqzZ9
FVEsjmQ5lqUj+xdxBpiUOdUpc22IJ4VcpBgQ2HrThvg6vf4aq937RJ/g4vi/g0SU
Utk0a3bUw1H/WnYAfJVFx83nVEsS/954Z7/ERDg1sjlfLYwQtQnpov0XIbPIbZU=
=k9IT
-----END PGP SIGNATURE-----
Merge tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI updates from James Bottomley:
"This is the usual grab bag of driver updates (lpfc, hpsa,
megaraid_sas, cxgbi, be2iscsi) plus an assortment of minor updates.
There is also one new driver: the Cisco snic. The advansys driver has
been rewritten to get rid of the warning about converting it to the
DMA API, the tape statistics patch got in and finally, there's a
resuffle of SCSI header files to separate more cleanly initiator from
target mode (and better share the common definitions)"
* tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi: (156 commits)
snic: driver for Cisco SCSI HBA
qla2xxx: Fix indentation
qla2xxx: Comment out unreachable code
fusion: remove dead MTRR code
advansys: fix compilation errors and warnings when CONFIG_PCI is not set
mptsas: fix depth param in scsi_track_queue_full
megaraid: fix irq setup process regression
lpfc: Update version to 10.7.0.0 for upstream patch set.
lpfc: Fix to drop PLOGIs from fabric node till LOGO processing completes
lpfc: Fix scsi task management error message.
lpfc: Fix cq_id masking problem.
lpfc: Fix scsi prep dma buf error.
lpfc: Add support for using block multi-queue
lpfc: Devices are not discovered during takeaway/giveback testing
lpfc: Fix vport deletion failure.
lpfc: Check for active portpeerbeacon.
lpfc: Update driver version for upstream patch set 10.6.0.1.
lpfc: Change buffer pool empty message to miscellaneous category
lpfc: Fix incorrect log message reported for empty FCF record.
lpfc: Fix rport leak.
...
SAM mandates that an BUS DEVICE RESET FUNCTION OCCURRED
UA needs to be send after a LUN RESET tmr has completed.
(Update to use target_ua_allocate_lun - hch)
Signed-off-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
We need to use 'se_dev_entry' as argument when allocating
UAs, otherwise we'll never see any UAs for an implicit
ALUA state transition triggered from userspace.
(Add target_ua_allocate_lun() common caller - nab)
Signed-off-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
As we're now using a list to hold the LUNs the target core
can now converted to use 64-bit LUNs internally.
Signed-off-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Only include SCSI initiator header files in target code that needs
these header files, namely the SCSI pass-through code and the tcm_loop
driver. Change SCSI_SENSE_BUFFERSIZE into TRANSPORT_SENSE_BUFFER in
target code because the former is intended for initiator code and the
latter for target code. With this patch the only initiator include
directives in target code that remain are as follows:
$ git grep -nHE 'include .scsi/(scsi.h|scsi_host.h|scsi_device.h|scsi_cmnd.h)' drivers/target drivers/infiniband/ulp/{isert,srpt} drivers/usb/gadget/legacy/tcm_*.[ch] drivers/{vhost,xen} include/{target,trace/events/target.h}
drivers/target/loopback/tcm_loop.c:29:#include <scsi/scsi.h>
drivers/target/loopback/tcm_loop.c:31:#include <scsi/scsi_host.h>
drivers/target/loopback/tcm_loop.c:32:#include <scsi/scsi_device.h>
drivers/target/loopback/tcm_loop.c:33:#include <scsi/scsi_cmnd.h>
drivers/target/target_core_pscsi.c:39:#include <scsi/scsi_device.h>
drivers/target/target_core_pscsi.c:40:#include <scsi/scsi_host.h>
drivers/xen/xen-scsiback.c:52:#include <scsi/scsi_host.h> /* SG_ALL */
Signed-off-by: Bart Van Assche <bart.vanassche@sandisk.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
Conflicts:
drivers/net/phy/amd-xgbe-phy.c
drivers/net/wireless/iwlwifi/Kconfig
include/net/mac80211.h
iwlwifi/Kconfig and mac80211.h were both trivial overlapping
changes.
The drivers/net/phy/amd-xgbe-phy.c file got removed in 'net-next' and
the bug fix that happened on the 'net' side is already integrated
into the rest of the amd-xgbe driver.
Signed-off-by: David S. Miller <davem@davemloft.net>
With se_port and t10_alua_tg_pt_gp_member being absored into se_lun,
there is no need for an extra lock to protect se_lun->lun_se_dev
assignment.
This patch also converts backend drivers to use call_rcu() release
to allow any se_device readers to complete. The call_rcu() instead
of kfree_rcu() is required here because se_device is embedded into
the backend driver specific structure.
Also, convert se_lun->lun_stats to use atomic_long_t within the
target_complete_ok_work() completion callback, and add FIXME for
transport_lookup_tmr_lun() with se_lun->lun_ref.
Finally, update sbp_update_unit_directory() special case usage with
proper rcu_dereference_raw() and configfs symlink comment.
Reported-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Cc: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Cc: Chris Boot <bootc@bootc.net>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This patch eliminates all se_port + t10_alua_tg_pt_gp_member usage,
and converts current users to direct se_lun pointer dereference.
This includes the removal of core_export_port(), core_release_port()
core_dev_export() and core_dev_unexport(). Along with conversion
of special case se_lun pointer dereference within PR ALL_TG_PT=1
and ALUA access state transition UNIT_ATTENTION handling.
Also, update core_enable_device_list_for_node() to reference the
new per se_lun->lun_deve_list when creating a new entry, or
replacing an existing one via RCU.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Instead of starting a thread from transport_clear_lun_ref() that
waits for LUN shutdown, wait in that function for LUN shutdown
to finish. Additionally, change the return type of
transport_clear_lun_ref() from int to void.
Signed-off-by: Bart Van Assche <bart.vanassche@sandisk.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This patch converts se_tpg->acl_node_lock to struct mutex, so that
->acl_node_acl walkers in core_clear_lun_from_tpg() can block when
calling core_disable_device_list_for_node().
It also updates core_dev_add_lun() to hold ->acl_node_mutex when
calling core_tpg_add_node_to_devs() to build ->lun_entry_hlist
for dynamically generated se_node_acl.
Reviewed-by: Hannes Reinecke <hare@suse.de>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Sagi Grimberg <sagig@mellanox.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
The only instance of ->put_session is in qla2xxx, and was added by commit
aaf68b ("tcm_qla2xxx: Convert to TFO->put_session() usage") with the following
description:
This patch converts tcm_qla2xxx code to use an internal kref_put() for
se_session->sess_kref in order to ensure that qla_hw_data->hardware_lock
can be held while calling qlt_unreg_sess() for the final put.
But these day we're already holding the hardware lock over qlt_unreg_sess in
the ->close_session callback, so we're fine without this method.
(Re-add missing tcm_qla2xxx_release_session + drop put_session usage - nab)
Signed-off-by: Christoph Hellwig <hch@lst.de>
Acked-by: Himanshu Madhani <himanshu.madhani@qlogic.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Simplify target core and target drivers by storing the task tag
a.k.a. command identifier inside struct se_cmd.
For several transports (e.g. SRP) tags are 64 bits wide.
Hence add support for 64-bit tags.
(Fix core_tmr_abort_task conversion spec warnings - nab)
(Fix up usb-gadget to use 16-bit tags - HCH + bart)
Signed-off-by: Bart Van Assche <bart.vanassche@sandisk.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Andy Grover <agrover@redhat.com>
Cc: Sagi Grimberg <sagig@mellanox.com>
Cc: <qla2xxx-upstream@qlogic.com>
Cc: Felipe Balbi <balbi@ti.com>
Cc: Michael S. Tsirkin <mst@redhat.com>
Cc: Juergen Gross <jgross@suse.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Even if the device backend is initialized with protection info is
enabled, some requests don't have the protection info attached for
WRITE SAME command issued by block device helpers, WRITE command with
WRPROTECT=0 by SG_IO ioctl, etc.
So when TCM loopback fabric module is used, se_cmd->t_prot_sg is NULL
for these requests and performing WRITE_INSERT of PI using software
emulation by sbc_dif_generate() causes kernel crash.
To fix this, introduce SCF_PASSTHROUGH_PROT_SG_TO_MEM_NOALLOC for
se_cmd_flags, which is used to determine that se_cmd->t_prot_sg needs
to be allocated or use pre-allocated protection information by scsi
mid-layer.
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Cc: Nicholas Bellinger <nab@linux-iscsi.org>
Cc: Sagi Grimberg <sagig@mellanox.com>
Cc: "Martin K. Petersen" <martin.petersen@oracle.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: "James E.J. Bottomley" <James.Bottomley@HansenPartnership.com>
Cc: target-devel@vger.kernel.org
Cc: linux-scsi@vger.kernel.org
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
The first argument of these two functions is always identical
to se_cmd->se_sess. Hence remove the first argument.
Signed-off-by: Bart Van Assche <bart.vanassche@sandisk.com>
Reviewed-by: Sagi Grimberg <sagig@mellanox.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Cc: Andy Grover <agrover@redhat.com>
Cc: <qla2xxx-upstream@qlogic.com>
Cc: Felipe Balbi <balbi@ti.com>
Cc: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Fields t_bidi_data_sg and t_bidi_data_nents are set only in the presence
of BIDI commands. This means that the underlying code (for example TCMU)
cannot inspect them when the SCSI command is not a BIDI one.
Ensure the code always initializes these fields with the given values,
even when the SCSI command is not a BIDI one. Set t_bidi_data_sg to
sgl_bidi (which should be NULL for non-BIDI commands) and
t_bidi_data_nents to sgl_bidi_count (which should be 0 for non-BIDI
commands). This allows the underlying code to use these fields
unconditionally.
Signed-off-by: Ilias Tsitsimpis <iliastsi@arrikto.com>
Signed-off-by: Vangelis Koukis <vkoukis@arrikto.com>
Reviewed-by: Andy Grover <agrover@redhat.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Drivers may override the WCE flag, in which case the DPOFUA flag in
MODE SENSE might differ from the check used to reject invalid FUA
bits in sbc_check_dpofua. Also now that we reject invalid FUA
bits early there is no need to duplicate the same buggy check
down in the fileio code.
As the DPOFUA flag controls th support for FUA bits on read and
write commands as well as DPO key off all the checks off a single
helper, and deprecate the emulate_dpo and emulate_fua_read attributs.
This fixes various failures in the libiscsi testsuite.
Personally I'd prefer to also remove the emulate_fua_write attribute
as there is no good reason to disable it, but I'll leave that for
a separate discussion.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Instead of providing DIF verify routines for read/write
that are almost identical and conditionally copy protection
information, just let the caller do the right thing.
Have a single sbc_dif_verify that handles an sgl (that
does NOT copy any data) and a protection information copy
routine used by rd_mcp and fileio backend.
In the WRITE case, call sbc_dif_verify with cmd->t_prot_sg
and then do the copy from it to local sgl (assuming the verify
succeeded of course). In the READ case, call sbc_dif_verify
with the local sgl and if it succeeds, copy it to t_prot_sg (or
not if we are stripping it).
(Fix apply breakage from commit c836777 - nab)
Tested-by: Akinobu Mita <akinobu.mita@gmail.com>
Signed-off-by: Sagi Grimberg <sagig@mellanox.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
It seems like we only care if a transport is passthrough or not. Convert
transport_type to a flags field and replace TRANSPORT_PLUGIN_* with a
flag, TRANSPORT_FLAG_PASSTHROUGH.
Signed-off-by: Andy Grover <agrover@redhat.com>
Reviewed-by: Ilias Tsitsimpis <iliastsi@arrikto.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
All of these files were only building on non-x86 because of
the indirect of inclusion of vmalloc.h by, of all things,
"net/inet_hashtables.h"
None of this got caught during build testing, because on x86
there is an implicit vmalloc.h include via on of the arch asm/
headers.
This fixes all of these
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
Code like " &= ~CMD_T_BUSY | ..." only clears CMD_T_BUSY but not
the other flag. Modify these statements such that both flags are
cleared.
(Fix fuzz for target_write_prot_action code in mainline - nab)
Signed-off-by: Bart Van Assche <bart.vanassche@sandisk.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
The function transport_complete_qf() must call either
queue_data_in() or queue_status() but not both.
Signed-off-by: Bart Van Assche <bart.vanassche@sandisk.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Pull SCSI target updates from Nicholas Bellinger:
"Lots of activity in target land the last months.
The highlights include:
- Convert fabric drivers tree-wide to target_register_template() (hch
+ bart)
- iser-target hardening fixes + v1.0 improvements (sagi)
- Convert iscsi_thread_set usage to kthread.h + kill
iscsi_target_tq.c (sagi + nab)
- Add support for T10-PI WRITE_STRIP + READ_INSERT operation (mkp +
sagi + nab)
- DIF fixes for CONFIG_DEBUG_SG=y + UNMAP file emulation (akinobu +
sagi + mkp)
- Extended TCMU ABI v2 for future BIDI + DIF support (andy + ilias)
- Fix COMPARE_AND_WRITE handling for NO_ALLLOC drivers (hch + nab)
Thanks to everyone who contributed this round with new features,
bug-reports, fixes, cleanups and improvements.
Looking forward, it's currently shaping up to be a busy v4.2 as well"
* 'for-next' of git://git.kernel.org/pub/scm/linux/kernel/git/nab/target-pending: (69 commits)
target: Put TCMU under a new config option
target: Version 2 of TCMU ABI
target: fix tcm_mod_builder.py
target/file: Fix UNMAP with DIF protection support
target/file: Fix SG table for prot_buf initialization
target/file: Fix BUG() when CONFIG_DEBUG_SG=y and DIF protection enabled
target: Make core_tmr_abort_task() skip TMFs
target/sbc: Update sbc_dif_generate pr_debug output
target/sbc: Make internal DIF emulation honor ->prot_checks
target/sbc: Return INVALID_CDB_FIELD if DIF + sess_prot_type disabled
target: Ensure sess_prot_type is saved across session restart
target/rd: Don't pass incomplete scatterlist entries to sbc_dif_verify_*
target: Remove the unused flag SCF_ACK_KREF
target: Fix two sparse warnings
target: Fix COMPARE_AND_WRITE with SG_TO_MEM_NOALLOC handling
target: simplify the target template registration API
target: simplify target_xcopy_init_pt_lun
target: remove the unused SCF_CMD_XCOPY_PASSTHROUGH flag
target/rd: reduce code duplication in rd_execute_rw()
tcm_loop: fixup tpgt string to integer conversion
...
The following incremental patch saves the current sess_prot_type into
se_node_acl, and will always reset sess_prot_type if a previous saved
value exists. So the PI setting for the fabric's session with backend
devices not supporting PI is persistent across session restart.
(Fix se_node_acl dereference for discovery sessions - DanCarpenter)
Reviewed-by: Martin Petersen <martin.petersen@oracle.com>
Reviewed-by: Sagi Grimberg <sagig@mellanox.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
The flag SCF_ACK_KREF is only set but never tested. Hence remove
this flag.
Signed-off-by: Bart Van Assche <bart.vanassche@sandisk.com>
Cc: Christoph Hellwig <hch@lst.de>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Avoid that sparse complains about context imbalances.
Signed-off-by: Bart Van Assche <bart.vanassche@sandisk.com>
Cc: Christoph Hellwig <hch@lst.de>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Linus Torvalds