The I2C-bus to the XPower AXP288 is shared between the Linux kernel and
the SoCs P-Unit. The P-Unit has a semaphore which the kernel must "lock"
before it may use the bus. If not explicitly taken by the I2C-driver,
then this semaphore is automatically taken by the I2C-bus-driver for
each I2C-transfer and this is a quite expensive operation.
Explicitly take the semaphore in probe() around the register-accesses
done during probe, so that this only needs to be done once, rather then
once per register-access.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
The I2C-bus to the XPower AXP288 is shared between the Linux kernel and
the SoCs P-Unit. The P-Unit has a semaphore which the kernel must "lock"
before it may use the bus. If not explicitly taken by the I2C-driver,
then this semaphore is automatically taken by the I2C-bus-driver for
each I2C-transfer.
Move the AXP20X_CC_CTRL check done in probe() together with the other
register-accesses done in probe, so that we can take the semaphore once
for the entire set of register-accesses.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
The I2C-bus to the XPower AXP288 is shared between the Linux kernel and
the SoCs P-Unit. The P-Unit has a semaphore which the kernel must "lock"
before it may use the bus and while the kernel holds the semaphore the CPU
and GPU power-states must not be changed otherwise the system will freeze.
This is a complex process, which is quite expensive. This is all done by
iosf_mbi_block_punit_i2c_access(). To ensure that no unguarded I2C-bus
accesses happen, iosf_mbi_block_punit_i2c_access() gets called by the
I2C-bus-driver for every I2C transfer. Because this is so expensive it
is allowed to call iosf_mbi_block_punit_i2c_access() in a nested
fashion, so that higher-level code which does multiple I2C-transfers can
call it once for a group of transfers, turning the calls done by the
I2C-bus-driver into no-ops.
Userspace power-supply API users typically will read all provided
properties in one go, refreshing the last read values when
power_supply_changed() is called by the driver and/or periodically
(e.g. every 2 minutes).
The reading of all properties in one go causes the P-Unit semaphore
to quickly be taken and released multiple times in a row. Certain
PMIC registers like AXP20X_FG_RES are even used in multiple properties
so they get read multiple times, leading to a P-Unit take + release
each time the register is read.
As already mentioned the taking of the P-Unit semaphore is a quite
expensive operation and it has also been reported that the
"hammering" of the P-Unit semaphore done by the axp288_fuel_gauge
driver can even cause stability issues with the system as a whole.
Switch over to a scheme where the axp288_fuel_gauge driver keeps
a local copy of all the registers which it uses for properties
and make it only refresh its copy of the registers if the values
are older then 1 minute; or when a fuel-gauge interrupt has
triggered since the last read.
This not only reduces the amount of reads, it also makes the code
do all the reads in one go, rather then reading specific registers
based on which property is being queried. This allows calling
iosf_mbi_block_punit_i2c_access() once before doing all the reads,
so that we now only take the P-Unit semaphore once per update.
Tested-by: Andrejus Basovas <cpp@gcc.lt>
Signed-off-by: Andrejus Basovas <cpp@gcc.lt>
Co-developed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Accessing registers on the AXP288 is quite expensive, so we should avoid
doing unnecessary accesses.
The FG_LOW_CAP_REG never changes underneath us, so we only need to read
it once. Devices with an AXP288 do not have user-replace (let alone
hot-swappable) batteries and the only bit we care about in the
PWR_OP_MODE register is the CHRG_STAT_BAT_PRESENT bit, so we can get
away with only reading the PWR_OP_MODE register once too.
Note that the FG_LOW_CAP_REG is not marked volatile in the regmap, so we
were effectively already reading it once. This change makes this explicit,
this is done as preparation of a further patch which moves all remaining
register accesses in fuel_gauge_get_property() out of that function.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Directly store the struct device pointer in axp288_fg_info, rather then
storing a pointer to the struct platform_device there and then using
"&info->pdev->dev" everywhere.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
The I2C-bus to the XPower AXP288 is shared between the Linux kernel and
the SoCs P-Unit. The P-Unit has a semaphore which the kernel must "lock"
before it may use the bus. This semaphore is automatically taken by the
I2C-bus-driver.
The retry on -EBUSY logic in fuel_gauge_reg_readb() likely was added to
deal with the I2C-bus-drive returning -EBUSY when it failed to take the
semaphore, but this really should never happen. The semaphore code even
has a WARN_ON(ret) to log a kernel backtrace if this does somehow happen,
when this happens something is seriously wrong and the system typically
freezes soon afterwards.
TL;DR: the regmap_read() should never fail with -EBUSY so the retries
are unnecessary.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
When fuel_gauge_reg_readb()/_writeb() fails, report which register we
were trying to read / write when the error happened.
Also reword the message a bit:
- Drop the axp288 prefix, dev_err() already prints this
- Switch from telegram / abbreviated style to a normal sentence, aligning
the message with those from fuel_gauge_read_*bit_word()
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Drop the IRQ mapping messages, because they are really not
interesting at all.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
The debugfs code is simply just dumping a bunch of registers, the same
information can also easily be gotten through the regmap debugfs
interface or through the i2cdump utility.
I've not used the debugfs interface once in all these years that I've
been working on the axp288_fuel_gauge driver, so lets just remove it.
Note this also removes the temperature-channels from the list of
IIO ADC channels used by the driver, since these were only used in the
debugfs interface.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
The values of various defines used in the driver are not aligned
properly when tabsize is set to 8 (I guess they were created with
a different tabsize).
Properly align the defines to make the code easier to read.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
In the function sc27xx_fgu_probe(), when get irq failed,
platform_get_irq() logs an error message, so remove
redundant message here.
Signed-off-by: Tang Bin <tangbin@cmss.chinamobile.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Deal with deferred probe using dev_err_probe so the error is handled
and avoid logging lots probe defer information like the following:
[ 9.125121] cw2015 4-0062: Failed to register power supply
[ 9.211131] cw2015 4-0062: Failed to register power supply
Fixes: b4c7715c10 ("power: supply: add CellWise cw2015 fuel gauge driver")
Signed-off-by: Peter Robinson <pbrobinson@gmail.com>
Reviewed-by: Javier Martinez Canillas <javierm@redhat.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
This patch adds a driver for PCHG (Peripheral CHarGer). PCHG is a
framework managing power supplies for peripheral devices.
This driver creates a sysfs node for each peripheral charge port:
/sys/class/power_supply/peripheral<n>
where <n> is the index of a charge port.
For example, when a stylus is connected to a NFC/WLC port, the node
returns:
/sys/class/power_supply/peripheral0/
capacity=50
charge_type=Standard
scope=Device
status=Charging
type=Battery
Signed-off-by: Daisuke Nojiri <dnojiri@chromium.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
This file isn't using any AB8500 symbols so drop these includes.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
If we rename the "abx500_chargalg" supply to "ab8500_chargalg"
as it should be named, the existing supplies are supplying that
supply but that was obviously not working since it had the
wrong name.
Now that the dependency kicks in we get a bunch
of NULL references from ab8500_chargalg_external_power_changed()
so check that the workqueue is allocated before we try to
queue work on it.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Drop the entire idea with abx500 being abstract and different from ab8500
in the AB8500 charging drivers. This rids the two identical definitions
of a slew of structs in ab8500-bm.h and makes things less confusion and
easier to understand.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
The "abx500" name on the charging algorithm stems from the ambition
to produce a series of these analog basebands, re-using the same
charging algorithm driver. No ASICs beside AB8500 and AB8505 were
ever produced so this terminology is confusing. Rename the
algorithm file and symbols to reflect the more narrow scope.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
The kernel already has a static inline for linear interpolation
so use that instead of rolling our own.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
kernel.h is being used as a dump for all kinds of stuff for a long time.
Here is the attempt to start cleaning it up by splitting out panic and
oops helpers.
There are several purposes of doing this:
- dropping dependency in bug.h
- dropping a loop by moving out panic_notifier.h
- unload kernel.h from something which has its own domain
At the same time convert users tree-wide to use new headers, although for
the time being include new header back to kernel.h to avoid twisted
indirected includes for existing users.
[akpm@linux-foundation.org: thread_info.h needs limits.h]
[andriy.shevchenko@linux.intel.com: ia64 fix]
Link: https://lkml.kernel.org/r/20210520130557.55277-1-andriy.shevchenko@linux.intel.com
Link: https://lkml.kernel.org/r/20210511074137.33666-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Co-developed-by: Andrew Morton <akpm@linux-foundation.org>
Acked-by: Mike Rapoport <rppt@linux.ibm.com>
Acked-by: Corey Minyard <cminyard@mvista.com>
Acked-by: Christian Brauner <christian.brauner@ubuntu.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Kees Cook <keescook@chromium.org>
Acked-by: Wei Liu <wei.liu@kernel.org>
Acked-by: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Acked-by: Sebastian Reichel <sre@kernel.org>
Acked-by: Luis Chamberlain <mcgrof@kernel.org>
Acked-by: Stephen Boyd <sboyd@kernel.org>
Acked-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Acked-by: Helge Deller <deller@gmx.de> # parisc
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Trying to get the AB8500 charging driver working I ran into a bit
of bitrot: we haven't used the driver for a while so errors in
refactorings won't be noticed.
This one is pretty self evident: use argument to the macro or we
end up with a random pointer to something else.
Cc: stable@vger.kernel.org
Cc: Krzysztof Kozlowski <krzk@kernel.org>
Cc: Marcus Cooper <codekipper@gmail.com>
Fixes: 297d716f62 ("power_supply: Change ownership from driver to core")
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
The continue statement at the end of a for-loop has no effect,
invert the if expression and remove the continue.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
It turns out that the "T3 MRD" DMI_BOARD_NAME value is used in a lot of
different Cherry Trail x5-z8300 / x5-z8350 based Mini-PC / HDMI-stick
models from Ace PC / Meegopad / MinisForum / Wintel (and likely also
other vendors).
Most of the other DMI strings on these boxes unfortunately contain various
generic values like "Default string" or "$(DEFAULT_STRING)", so we cannot
match on them. These devices do have their chassis-type correctly set to a
value of "3" (desktop) which is a pleasant surprise, so also match on that.
This should avoid the quirk accidentally also getting applied to laptops /
tablets (which do actually have a battery). Although in my quite large
database of Bay and Cherry Trail based devices DMIdecode dumps I don't
have any laptops / tables with a board-name of "T3 MRD", so this should
not be an issue.
BugLink: https://askubuntu.com/questions/1206714/how-can-a-mini-pc-be-stopped-from-being-detected-as-a-laptop-with-a-battery/
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
As documented in the updated "Naming" chapter of
Documentation/process/coding-style.rst, usage of the work blacklist
should be avoided where possible.
Rename the list of devices which have no battery to the
axp288_no_battery_list, which also more accurately describes the
contents of the list.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
The driver can match only via the DT table so the table should be always
used and the of_match_ptr() does not have any sense (this also allows ACPI
matching via PRP0001, even though it might be not relevant here). This
fixes compile warning (!CONFIG_OF):
drivers/power/supply/bq24190_charger.c:1972:34: warning: ‘bq24190_of_match’ defined but not used [-Wunused-const-variable=]
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
This patch adds missing MODULE_DEVICE_TABLE definition which generates
correct modalias for automatic loading of this driver when it is built
as an external module.
Signed-off-by: Yu Jiahua <yujiahua1@huawei.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
This patch adds missing MODULE_DEVICE_TABLE definition which generates
correct modalias for automatic loading of this driver when it is built
as an external module.
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Zou Wei <zou_wei@huawei.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
This patch adds missing MODULE_DEVICE_TABLE definition which generates
correct modalias for automatic loading of this driver when it is built
as an external module.
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Zou Wei <zou_wei@huawei.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
This patch adds missing MODULE_DEVICE_TABLE definition which generates
correct modalias for automatic loading of this driver when it is built
as an external module.
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Zou Wei <zou_wei@huawei.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
This avoids reimplementing the detection logic twice and removes the
possibility of activating charging with 500mA even if a battery is not
detected.
Signed-off-by: Carl Philipp Klemm <philipp@uvos.xyz>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
This invalidates empty->counter_uah and charge_full when charge_now
indicates that they are grossly wrong and adds some tolerance to
POWER_SUPPLY_PROP_CHARGE_FULL to allow for inaccuracies in the charge
counter and manufacturing tolerances in the battery.
Signed-off-by: Carl Philipp Klemm <philipp@uvos.xyz>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Allow disabling and re-enabling battery charging of an axp209 PMIC
through a writable status property. With the current driver code
charging is always on.
This works on the axp209 of Banana {Pi M1+,Pro} and should work on all
AXP chips.
Signed-off-by: Hermann.Lauer@uni-heidelberg.de
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
There are no platforms using the driver with platform data (no board
files with the driver), so the dead code can be dropped.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
The driver was reporting POWER_SUPPLY_PROP_ONLINE via platform data
functions or '1' if no platform data was provided. Since there are no
platforms using the driver with platform data (no board files with the
driver), the online property can be simplified to always return '1'.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
The driver was reporting POWER_SUPPLY_PROP_STATUS via platform data
functions. Without platform data, the max17040_get_status() functions
returns early with POWER_SUPPLY_STATUS_UNKNOWN. Since there are no
platforms using the driver with platform data (no board files with the
driver), the status property was always unknown.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
When devm_ioremap_resource() fails, a clear enough error message will be
printed by its subfunction __devm_ioremap_resource(). The error
information contains the device name, failure cause, and possibly resource
information.
Therefore, remove the error printing here to simplify code and reduce the
binary size.
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Zhen Lei <thunder.leizhen@huawei.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
This patch adds missing MODULE_DEVICE_TABLE definition which generates
correct modalias for automatic loading of this driver when it is built
as an external module.
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Bixuan Cui <cuibixuan@huawei.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
The fuel gauge in the RT5033 PMIC has its own I2C bus and interrupt
line. Therefore, it is not actually part of the RT5033 MFD and needs
its own of_match_table to probe properly.
Also, given that it's independent of the MFD, there is actually
no need to make the Kconfig depend on MFD_RT5033. Although the driver
uses the shared <linux/mfd/rt5033.h> header, there is no compile
or runtime dependency on the RT5033 MFD driver.
Cc: Beomho Seo <beomho.seo@samsung.com>
Cc: Chanwoo Choi <cw00.choi@samsung.com>
Fixes: b847dd96e6 ("power: rt5033_battery: Add RT5033 Fuel gauge device driver")
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
The only known BD70528 use-cases are such that the PMIC is controlled
from separate MCU which is not running Linux. I am not aware of
any Linux driver users. Furthermore, it seems there is no demand for
this IC. Let's ease the maintenance burden and drop the driver. We can
always add it back if there is sudden need for it.
Signed-off-by: Matti Vaittinen <matti.vaittinen@fi.rohmeurope.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Interrupt line can be configured on different hardware in different way,
even inverted. Therefore driver should not enforce specific trigger
type - edge falling - but instead rely on Devicetree to configure it.
The Maxim 14577/77836 datasheets describe the interrupt line as active
low with a requirement of acknowledge from the CPU therefore the edge
falling is not correct.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Acked-by: Iskren Chernev <iskren.chernev@gmail.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Interrupt line can be configured on different hardware in different way,
even inverted. Therefore driver should not enforce specific trigger
type - edge falling - but instead rely on Devicetree to configure it.
The Maxim 17047/77693 datasheets describe the interrupt line as active
low with a requirement of acknowledge from the CPU therefore the edge
falling is not correct.
The interrupt line is shared between PMIC and RTC driver, so using level
sensitive interrupt is here especially important to avoid races. With
an edge configuration in case if first PMIC signals interrupt followed
shortly after by the RTC, the interrupt might not be yet cleared/acked
thus the second one would not be noticed.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
The ac->state field is __le32, not u32. So change the variable we're
temporarily storing it in to __le32 as well.
Reported-by: kernel test robot <lkp@intel.com>
Fixes: e61ffb3445 ("power: supply: Add AC driver for Surface Aggregator Module")
Signed-off-by: Maximilian Luz <luzmaximilian@gmail.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Currently sbs-battery supports three string properties -
manufacturer, model_name, and chemistry. Buffers for those
properties are currently defined as global variables.
This patch moves those global variables into struct sbs_info
and cache/reuse them as they are all constant values.
Signed-off-by: Ikjoon Jang <ikjn@chromium.org>
Tested-by: Hsin-Yi Wang <hsinyi@chromium.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Adds properties for setting the maximum current to USB, ADP and Battery
supplies. USB and ADP limits are reset to OTP values upon replugging.
Signed-off-by: Andreas Kemnade <andreas@kemnade.info>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
The RC5T619 can detect SDP, CDP and DCP chargers, so let's add support
for it.
Signed-off-by: Andreas Kemnade <andreas@kemnade.info>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
This driver is including the legacy GPIO header <linux/gpio.h>
but not using any symbols from it. Delete the include.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Dmitry Osipenko <digetx@gmail.com>
Acked-by: David Heidelberg <david@ixit.cz>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
The PM2301 was only used in tandem with AB9540, part of U9540,
a platform that was cancelled and never deployed in products.
Delete it.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
The result of container_of() operations is never NULL unless the element
is the first element of the embedded structure, which is not the case here.
The NULL check is therefore unnecessary and misleading. Remove it.
This change was made automatically with the following Coccinelle script.
@@
type t;
identifier v;
statement s;
@@
<+...
(
t v = container_of(...);
|
v = container_of(...);
)
...
when != v
- if (\( !v \| v == NULL \) ) s
...+>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
This setting is read directly from the device tree in
the ab8500_charger.c code.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
The vendor code tree supplies platform data to enable he
USB charging for AB8500 and AB8500 and disable the AC
charging on the AB8505. This was missed when the driver
was submitted to the mainline kernel.
Fix this by doing what the vendor kernel does: always
register the USB charger, do not register the AC charger
on the AB8505.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Sometimes the code will crash because we haven't enabled
AC or USB charging and thus not created the corresponding
psy device. Fix it by checking that it is there before
notifying.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
The code was calling ab8500_bm_of_probe() in four different
spots effectively overwriting the same configuration three
times. This was done because probe order was uncertain.
Since we now used componentized probe, call it only once
while probing the main charging component.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
The driver has problems with the different components of
the charging code racing with each other to probe().
This results in all four subdrivers populating battery
information to ascertain that it is populated for their
own needs for example.
Fix this by using component probing and thus expressing
to the kernel that these are dependent components.
The probes can happen in any order and will only acquire
resources such as state container, regulators and
interrupts and initialize the data structures, but no
execution happens until the .bind() callback is called.
The charging driver is the main component and binds
first, then bind in order the three subcomponents:
ab8500-fg, ab8500-btemp and ab8500-chargalg.
Do some housekeeping while we are moving the code around.
Like use devm_* for IRQs so as to cut down on some
boilerplate.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
The battery subsystem of the Surface Aggregator Module EC requires us to
register the battery notifier with instance ID 0. However, battery
events are actually sent with the instance ID corresponding to the
device, which is nonzero. Thus, the strict-matching approach doesn't
work here and will discard events that the driver is expected to handle.
To fix this we have to fall back on notifier matching by target-category
only and have to manually check the instance ID in the notifier
callback.
Fixes: 167f77f7d0 ("power: supply: Add battery driver for Surface Aggregator Module")
Signed-off-by: Maximilian Luz <luzmaximilian@gmail.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
This patch adds missing MODULE_DEVICE_TABLE definition which generates
correct modalias for automatic loading of this driver when it is built
as an external module.
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Zou Wei <zou_wei@huawei.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
This patch adds missing MODULE_DEVICE_TABLE definition which generates
correct modalias for automatic loading of this driver when it is built
as an external module.
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Zou Wei <zou_wei@huawei.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
battery/charger driver changes:
* core: provide function stubs if CONFIG_POWER_SUPPLY=n
* core: reduce loglevel for probe defer info
* surface-battery: new battery driver for Surface
* surface-charger: new charger driver for Surface
* bq27xxx: add bq78z100 support
* bq27xxx: fix current_now/power_avg for newer chips
* cw2015: add CHARGE_NOW support
* ab8500: drop pdata support
* convert most DT bindings to YAML
* lot's of minor fixes and cleanups
reset drivers:
* ltc2952-poweroff: make trigger delay configurable from DT
* minor fixes and cleanups
-----BEGIN PGP SIGNATURE-----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=9IUN
-----END PGP SIGNATURE-----
Merge tag 'for-v5.13' of git://git.kernel.org/pub/scm/linux/kernel/git/sre/linux-power-supply
Pull power supply and reset updates from Sebastian Reichel:
"battery/charger driver changes:
- core:
- provide function stubs if CONFIG_POWER_SUPPLY=n
- reduce loglevel for probe defer info
- surface:
- new battery and charger drivers for Surface
- bq27xxx:
- add bq78z100 support
- fix current_now/power_avg for newer chips
- cw2015:
- add CHARGE_NOW support
- ab8500:
- drop pdata support
- convert most DT bindings to YAML
- lots of minor fixes and cleanups
reset drivers:
- ltc2952-poweroff:
- make trigger delay configurable from DT
- minor fixes and cleanups"
* tag 'for-v5.13' of git://git.kernel.org/pub/scm/linux/kernel/git/sre/linux-power-supply: (97 commits)
power: supply: cpcap-battery: fix invalid usage of list cursor
power: supply: bq256xx: add kerneldoc for structure members
power: supply: act8945a: correct kerneldoc
power: supply: max17040: remove unneeded double cast
power: supply: max17040: handle device_property_read_u8_array() failure
power: supply: max14577: remove unneeded variable initialization
power: supply: surface-charger: Make symbol 'surface_ac_pm_ops' static
power: supply: surface-battery: Make some symbols static
power: reset: restart-poweroff: Add missing MODULE_DEVICE_TABLE
power: reset: hisi-reboot: add missing MODULE_DEVICE_TABLE
power: supply: s3c_adc_battery: fix possible use-after-free in s3c_adc_bat_remove()
power: supply: generic-adc-battery: fix possible use-after-free in gab_remove()
power: supply: Add AC driver for Surface Aggregator Module
power: supply: Add battery driver for Surface Aggregator Module
power: supply: bq25980: Move props from battery node
power: supply: core: Use true and false for bool variable
power: supply: goldfish: Remove the GOLDFISH dependency
power: reset: ltc2952: make trigger delay configurable
power: supply: cpcap-charger: Simplify bool conversion
power: supply: cpcap-charger: Add usleep to cpcap charger to avoid usb plug bounce
...
Fix invalid usage of a list_for_each_entry in cpcap_battery_irq_thread().
Empty list or fully traversed list points to list head, which is not
NULL (and before the first element containing real data).
Signed-off-by: Guangqing Zhu <zhuguangqing83@gmail.com>
Reviewed-by: Tony Lindgren <tony@atomide.com>
Reviewed-by: Carl Philipp Klemm <philipp@uvos.xyz>
Tested-by: Carl Philipp Klemm <philipp@uvos.xyz>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Document members of structure to fix W=1 warnings like:
drivers/power/supply/bq256xx_charger.c:240: warning:
Function parameter or member 'charger' not described in 'bq256xx_device'
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Remove incorrect kerneldoc marker to fix W=1 warning:
drivers/power/supply/act8945a_charger.c:22: warning:
This comment starts with '/**', but isn't a kernel-doc comment. Refer Documentation/doc-guide/kernel-doc.rst
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
There is no need for double explicit cast from of_device_get_match_data()
(uintptr_t and then to target enum) because implicit conversion from
uintptr_t to enum is straightforward (uintptr_t is a integer type).
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
The device_property_read_u8_array() call should not fail because it is
preceded with device_property_count_u8() and check for number of
readable u8 values. However the code is more obvious and easier to read
if the return value of device_property_read_u8_array() is checked.
Otherwise reader needs to investigate whether really there is no risk of
using random stack values of 'rcomp' variable.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
The local 'current_bits' variable does not have to be initialized
because all cases in following switch() either return or initialize it.
Addresses-Coverity: Unused value
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
The sparse tool complains as follows:
drivers/power/supply/surface_charger.c:229:1: warning:
symbol 'surface_ac_pm_ops' was not declared. Should it be static?
This symbol is not used outside of surface_charger.c, so this
commit marks it static.
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Qiheng Lin <linqiheng@huawei.com>
Acked-by: Maximilian Luz <luzmaximilian@gmail.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
The sparse tool complains as follows:
drivers/power/supply/surface_battery.c:700:1: warning:
symbol 'dev_attr_alarm' was not declared. Should it be static?
drivers/power/supply/surface_battery.c:805:1: warning:
symbol 'surface_battery_pm_ops' was not declared. Should it be static?
This symbol is not used outside of surface_battery.c, so this
commit marks it static.
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Qiheng Lin <linqiheng@huawei.com>
Acked-by: Maximilian Luz <luzmaximilian@gmail.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
This patch adds missing MODULE_DEVICE_TABLE definition which generates
correct modalias for automatic loading of this driver when it is built
as an external module.
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Bixuan Cui <cuibixuan@huawei.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
This patch adds missing MODULE_DEVICE_TABLE definition which generates
correct modalias for automatic loading of this driver when it is built
as an external module.
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Chen Lifu <chenlifu@huawei.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
This driver's remove path calls cancel_delayed_work(). However, that
function does not wait until the work function finishes. This means
that the callback function may still be running after the driver's
remove function has finished, which would result in a use-after-free.
Fix by calling cancel_delayed_work_sync(), which ensures that
the work is properly cancelled, no longer running, and unable
to re-schedule itself.
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
This driver's remove path calls cancel_delayed_work(). However, that
function does not wait until the work function finishes. This means
that the callback function may still be running after the driver's
remove function has finished, which would result in a use-after-free.
Fix by calling cancel_delayed_work_sync(), which ensures that
the work is properly cancelled, no longer running, and unable
to re-schedule itself.
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
On newer Microsoft Surface models (specifically 7th-generation, i.e.
Surface Pro 7, Surface Book 3, Surface Laptop 3, and Surface Laptop Go),
battery and AC status/information is no longer handled via standard ACPI
devices, but instead directly via the Surface System Aggregator Module
(SSAM), i.e. the embedded controller on those devices.
While on previous generation models, AC status is also handled via SSAM,
an ACPI shim was present to translate the standard ACPI AC interface to
SSAM requests. The SSAM interface itself, which is modeled closely after
the ACPI interface, has not changed.
This commit introduces a new SSAM client device driver to support AC
status/information via the aforementioned interface on said Surface
models.
Signed-off-by: Maximilian Luz <luzmaximilian@gmail.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
On newer Microsoft Surface models (specifically 7th-generation, i.e.
Surface Pro 7, Surface Book 3, Surface Laptop 3, and Surface Laptop Go),
battery and AC status/information is no longer handled via standard ACPI
devices, but instead directly via the Surface System Aggregator Module
(SSAM), i.e. the embedded controller on those devices.
While on previous generation models, battery status is also handled via
SSAM, an ACPI shim was present to translate the standard ACPI battery
interface to SSAM requests. The SSAM interface itself, which is modeled
closely after the ACPI interface, has not changed.
This commit introduces a new SSAM client device driver to support
battery status/information via the aforementioned interface on said
Surface models. It is in parts based on the standard ACPI battery
driver.
Signed-off-by: Maximilian Luz <luzmaximilian@gmail.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Currently POWER_SUPPLY_PROP_CONSTANT_CHARGE_CURRENT and
POWER_SUPPLY_PROP_CONSTANT_CHARGE_VOLTAGE are exposed on
the battery node and this is incorrect.
This patch exposes both of them on the charger node rather
than the battery node.
Fixes: 5069185fc1 ("power: supply: bq25980: Add support for the BQ259xx family")
Signed-off-by: Ricardo Rivera-Matos <r-rivera-matos@ti.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
-----BEGIN PGP SIGNATURE-----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=+5eM
-----END PGP SIGNATURE-----
Merge tag 'ib-mfd-power-v5.13' into psy-next
Immutable branch between MFD and Power due for the v5.13 merge window.
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
This will allow to use the BATTERY_GOLDFISH driver
without enabling GOLDFISH.
Signed-off-by: Roman Kiryanov <rkir@google.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Make trigger delay configurable through device tree with
trigger-delay-ms property.
Trigger delay is the time to wait before starting shutdown
sequence after trigger line assertion.
Trigger delay must take into account the OFFT time configured
with the capacitor connected to OFFT pin of the LTC2952 chip.
Basically, the higher the capacitance connected to OFFT pin,
the larger trigger delay must be.
Signed-off-by: Marek Czerski <ma.czerski@gmail.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Fix the following coccicheck warning:
./drivers/power/supply/cpcap-charger.c:416:31-36: WARNING: conversion to
bool not needed here
Reported-by: Abaci Robot <abaci@linux.alibaba.com>
Signed-off-by: Yang Li <yang.lee@linux.alibaba.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Adds 80000 us sleep when the usb cable is plugged in to hopefully avoid
bouncing contacts.
Upon pluging in the usb cable vbus will bounce for some time, causing cpcap to
dissconnect charging due to detecting an undervoltage condition. This is a
scope of vbus on xt894 while quickly inserting the usb cable with firm force,
probed at the far side of the usb socket and vbus loaded with approx 1k:
http://uvos.xyz/maserati/usbplug.jpg.
As can clearly be seen, vbus is all over the place for the first 15 ms or so
with a small blip at ~40 ms this causes the cpcap to trip up and disable
charging again.
The delay helps cpcap_usb_detect avoid the worst of this. It is, however, still
not ideal as strong vibrations can cause the issue to reapear any time during
charging. I have however not been able to cause the device to stop charging due
to this in practice as it is hard to vibrate the device such that the vbus pins
start bouncing again but cpcap_usb_detect is not called again due to a detected
disconnect/reconnect event.
Signed-off-by: Carl Philipp Klemm <philipp@uvos.xyz>
Tested-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Signed-off-by: Carl Philipp Klemm <philipp@uvos.xyz>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Avoid logging probe defer information for default loglevel
configurations. This is only required for debugging probe
defer issues, which requires enabling debug messages for
other subsystems.
This dev_info() message predates having deferred devices
information available in /sys/kernel/debug/devices_deferred,
which is generally more useful.
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
sbs-manager implements a GPIO chip, so include the proper
gpio driver include instead of the legacy gpio.h.
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Introduce usage of dev_err_probe in probe routine, which
makes the code slightly more readable and removes some
lines of code. It also removes PROBE_DEFER errors being
logged by default.
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Introduce usage of dev_err_probe in probe routine, which
makes the code slightly more readable and removes some
lines of code. It also removes PROBE_DEFER errors being
logged by default.
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Introduce usage of dev_err_probe in probe routine, which
makes the code slightly more readable and removes some
lines of code. It also removes PROBE_DEFER errors being
logged by default, which are common when the battery is
waiting for the charger driver to be registered.
This also cleans up a useless goto and instead returns
directly.
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Change 'long long int' to 'long long' because the int is unnecessary,
as suggested by checkpatch.pl.
Signed-off-by: Milan Djurovic <mdjurovic@zohomail.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Get regulator from parent device's node and extcon by name.
Signed-off-by: Timon Baetz <timon.baetz@protonmail.com>
Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
s/Hisilicon/HiSilicon/g.
It should use capital S, according to
https://www.hisilicon.com/en/terms-of-use.
Signed-off-by: Hao Fang <fanghao11@huawei.com>
Acked-by: Haojian Zhuang <haojian.zhuang@linaro.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Use devm_of_iomap() to map resources. This will avoid the necessity to
track the mapped resources and free them on failure path or on remove.
Reported-by: kernel test robot <lkp@intel.com>
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Suggested-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
The commit 6d0c5de2fd
("power: supply: Clean-up few drivers by using managed work init")
Re-introduced wrong order of initializing work-queue and requesting
the IRQs which was originally fixed by the commit b5e8642ed9
("power: supply: axp20x_usb_power: Init work before enabling IRQs")
In addition this caused the work queue to be initialized twice.
Fix it again.
Fixes: 6d0c5de2fd ("power: supply: Clean-up few drivers by using managed work init")
Signed-off-by: Matti Vaittinen <matti.vaittinen@fi.rohmeurope.com>
Reported-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Link: https://lore.kernel.org/r/a774ca25010b7c932c07f22ce8a548466705c023.1616574973.git.matti.vaittinen@fi.rohmeurope.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Normal parentheses should be used when referring to config variables
in Makefile. Replace the accidentally introduced curly brackets by
regular parentheses.
Fixes: a7f79f9954 ("power: reset: add driver for LinkStation power off")
Acked-by: Daniel González Cabanelas <dgcbueu@gmail.com>
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Few drivers implement remove call-back only for ensuring a delayed
work gets cancelled prior driver removal. Clean-up these by switching
to use devm_delayed_work_autocancel() instead.
This change is compile-tested only. All testing is appreciated.
Acked-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Signed-off-by: Matti Vaittinen <matti.vaittinen@fi.rohmeurope.com>
Link: https://lore.kernel.org/r/e5b1b0380cdd1aa066c9ac6d7a8b1a86ba1ddbbe.1616506559.git.matti.vaittinen@fi.rohmeurope.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There is a slew of defines, structs and enums and even a
function call only relevant for the charging code that
still lives in <linux/mfd/abx500.h>. Push it down to the
"ab8500-bm.h" header in the power supply subsystem where
it is actually used.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The charging algorithm header is only used locally in the
power supply subsystem so push this down into
drivers/power/supply and rename from the confusing
"ux500_chargalg.h" to "ab8500-chargalg.h" for clarity:
it is only used with the AB8500.
This is another remnant of non-DT code needing to pass
data from boardfiles, which we don't do anymore.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The global definition of platform data for the battery
management code has no utility after the OF conversion,
move the <linux/mfd/abx500/ab8500-bm.h> to be a local
file in drivers/power/supply and stop defining the
platform data in drivers/power/supply/ab8500_bmdata.c
and broadcast to the kernel only to have it assigned
as platform data to the MFD cells and then picked back
into the same subsystem that defined it in the first
place. This kills off a layer of indirection.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The core AB8500 driver and the whole platform is completely
dependent on being probed from device tree so remove the
non-DT probe paths.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Hans de Goede
