Apparently, the check for a 6-byte ID string introduced by commit
426c457a32 ("mtd: nand: extend NAND flash
detection to new MLC chips") is NOT sufficient to determine whether or
not a Samsung chip uses their new MLC detection scheme or the old,
standard scheme. This adds a condition to check cell type.
Signed-off-by: Tilman Sauerbeck <tilman@code-monkey.de>
Signed-off-by: Brian Norris <norris@broadcom.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Cc: stable@kernel.org
Commit c7b28e25cb ("mtd: nand: refactor BB
marker detection") caused a regression in detection of factory-set bad
block markers, especially for certain small-page NAND. This fix removes
some unneeded constraints on using NAND_SMALL_BADBLOCK_POS, making the
detection code more correct.
This regression can be seen, for example, in Hynix HY27US081G1M and
similar.
Signed-off-by: Brian Norris <norris@broadcom.com>
Tested-by: Michael Guntsche <mike@it-loops.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Test on a PXA310 platform with Samsung K9F2G08X0B NAND flash,
with tCH=5 and clk is 156MHz, ns2cycle(5, 156000000) returns -1.
ns2cycle returns negtive value will break NDTR0_tXX macros.
After checking the commit log, I found the problem is introduced by
commit 5b0d4d7c8a
"[MTD] [NAND] pxa3xx: convert from ns to clock ticks more accurately"
To get num of clock cycles, we use below equation:
num of clock cycles = time (ns) / one clock cycle (ns) + 1
We need to add 1 cycle here because integer division will truncate the result.
It is possible the developers set the Min values in SPEC for timing settings.
Thus the truncate may cause problem, and it is safe to add an extra cycle here.
The various fields in NDTR{01} are in units of clock ticks minus one,
thus we should subtract 1 cycle then.
Thus the correct equation should be:
num of clock cycles = time (ns) / one clock cycle (ns) + 1 - 1
= time (ns) / one clock cycle (ns)
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Lei Wen <leiwen@marvell.com>
Acked-by: Eric Miao <eric.y.miao@gmail.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Cc: stable@kernel.org
The drivers for Xilinx' SystemACE and physically mapped MTDs were missing
prototypes for of_address_to_resource(). This patch adds the necessary
headers.
Signed-off-by: Graeme Smecher <graeme.smecher@mail.mcgill.ca>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
* git://git.infradead.org/mtd-2.6:
mtd/nand_ids: Fix buswidth
mtd/m25p80: fix test for end of loop
mtd/m25p80: retlen is never NULL
MIPS: Fix gen_nand probe structures contents
gen_nand: Test if nr_chips field is valid
BFIN: Fix gen_nand probe structures contents
nand/denali: move all hardware initialization work to denali_hw_init
nand/denali: Add a page check in denali_read_page & denali_read_page_raw
nand/denali: use cpu_relax() while waiting for hardware interrupt
nand/denali: change read_status function method
nand/denali: Fixed check patch warnings
ARM: Fix gen_nand probe structures contents
mtd/nand_base: fix kernel-doc warnings & typos
nand/denali: use dev_xx debug function to replace nand_dbg_print and some printk
nand/denali: Fixed handle ECC error bugs
nand/denali: use iowrite32() to replace denali_write32()
nand/denali: Fixed probe function bugs
The buswidth for chips of ID 0xD7 is x8, not x16.
This was my previous typo.
Signed-off-by: Brian Norris <norris@broadcom.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
"plat_id" is always non-NULL here. There is a zero element on the end
of the m25p_ids[] array and if we hit the end of the loop then plat_id
points to that.
This would lead to a NULL pointer dereference later on in the function.
Signed-off-by: Dan Carpenter <error27@gmail.com>
Acked-by: Anton Vorontsov <cbouatmailru@gmail.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
This is just a cleanup, it doesn't fix any bugs.
These functions all check retlen inconsistently and it generates a
warning in Smatch (http://smatch.sf.net). If retlen were ever NULL it
would cause an oops and the code has been this way since 2006 so someone
would have complained. Also I looked at other places that implemented
the mtd read and write functions and they dereference retlen without
checking.
I removed the checks.
Signed-off-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
All hardware initialization will be done in denali_hw_init before
irq handler registered
Change mtd name from "DENALI NAND" to be "denali-nand" since whitespace in
name can cause problems if we use cmdlinepart
Signed-off-by: Chuanxiao Dong <chuanxiao.dong@intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
In mtd->write, Denali controller will use MODE_11 mode to read
NAND flash status, then return back to MODE_1O mode to do page
write.
Here comes a bug for this kind of using, sometimes controller will
not write data to NAND and just return a good interrupt to tell
driver writing work is done. The data in this page is all 0xff and
this page can not be written again. The reason is unknow.
So read Denali controller register WRITE_PROTECT to get NAND status
instead.
Signed-off-by: Chuanxiao Dong <chuanxiao.dong@intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
waring: no space for starting a line
Signed-off-by: Chuanxiao Dong <chuanxiao.dong@intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Fix mtd/nand_base.c kernel-doc warnings and typos.
Warning(drivers/mtd/nand/nand_base.c:893): No description found for parameter 'mtd'
Warning(drivers/mtd/nand/nand_base.c:893): No description found for parameter 'ofs'
Warning(drivers/mtd/nand/nand_base.c:893): No description found for parameter 'len'
Warning(drivers/mtd/nand/nand_base.c:893): No description found for parameter 'invert'
Warning(drivers/mtd/nand/nand_base.c:930): No description found for parameter 'mtd'
Warning(drivers/mtd/nand/nand_base.c:930): No description found for parameter 'ofs'
Warning(drivers/mtd/nand/nand_base.c:930): No description found for parameter 'len'
Warning(drivers/mtd/nand/nand_base.c:987): No description found for parameter 'mtd'
Warning(drivers/mtd/nand/nand_base.c:987): No description found for parameter 'ofs'
Warning(drivers/mtd/nand/nand_base.c:987): No description found for parameter 'len'
Warning(drivers/mtd/nand/nand_base.c:2087): No description found for parameter 'len'
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Cc: David Woodhouse <dwmw2@infradead.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fix mtd/nand_base.c kernel-doc warnings and typos.
Warning(drivers/mtd/nand/nand_base.c:893): No description found for parameter 'mtd'
Warning(drivers/mtd/nand/nand_base.c:893): No description found for parameter 'ofs'
Warning(drivers/mtd/nand/nand_base.c:893): No description found for parameter 'len'
Warning(drivers/mtd/nand/nand_base.c:893): No description found for parameter 'invert'
Warning(drivers/mtd/nand/nand_base.c:930): No description found for parameter 'mtd'
Warning(drivers/mtd/nand/nand_base.c:930): No description found for parameter 'ofs'
Warning(drivers/mtd/nand/nand_base.c:930): No description found for parameter 'len'
Warning(drivers/mtd/nand/nand_base.c:987): No description found for parameter 'mtd'
Warning(drivers/mtd/nand/nand_base.c:987): No description found for parameter 'ofs'
Warning(drivers/mtd/nand/nand_base.c:987): No description found for parameter 'len'
Warning(drivers/mtd/nand/nand_base.c:2087): No description found for parameter 'len'
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Once the last ECC error was handled, controller will triger an
interrupt. If this interrupt can not be clean on time, controller
may corrupt.
Signed-off-by: Chuanxiao Dong <chuanxiao.dong@intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
denali_write32() just implements a debug function for iowrite32(),
only print out the write value. Remove this function since it's useless
Signed-off-by: Chuanxiao Dong <chuanxiao.dong@intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Fixed a pci_resource_len function error;
Changed returning sequence of probe function;
Signed-off-by: Chuanxiao Dong <chuanxiao.dong@intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
* 'for-2.6.36' of git://git.kernel.dk/linux-2.6-block: (149 commits)
block: make sure that REQ_* types are seen even with CONFIG_BLOCK=n
xen-blkfront: fix missing out label
blkdev: fix blkdev_issue_zeroout return value
block: update request stacking methods to support discards
block: fix missing export of blk_types.h
writeback: fix bad _bh spinlock nesting
drbd: revert "delay probes", feature is being re-implemented differently
drbd: Initialize all members of sync_conf to their defaults [Bugz 315]
drbd: Disable delay probes for the upcomming release
writeback: cleanup bdi_register
writeback: add new tracepoints
writeback: remove unnecessary init_timer call
writeback: optimize periodic bdi thread wakeups
writeback: prevent unnecessary bdi threads wakeups
writeback: move bdi threads exiting logic to the forker thread
writeback: restructure bdi forker loop a little
writeback: move last_active to bdi
writeback: do not remove bdi from bdi_list
writeback: simplify bdi code a little
writeback: do not lose wake-ups in bdi threads
...
Fixed up pretty trivial conflicts in drivers/block/virtio_blk.c and
drivers/scsi/scsi_error.c as per Jens.
* git://git.infradead.org/mtd-2.6: (79 commits)
mtd: Remove obsolete <mtd/compatmac.h> include
mtd: Update copyright notices
jffs2: Update copyright notices
mtd-physmap: add support users can assign the probe type in board files
mtd: remove redwood map driver
mxc_nand: Add v3 (i.MX51) Support
mxc_nand: support 8bit ecc
mxc_nand: fix correct_data function
mxc_nand: add V1_V2 namespace to registers
mxc_nand: factor out a check_int function
mxc_nand: make some internally used functions overwriteable
mxc_nand: rework get_dev_status
mxc_nand: remove 0xe00 offset from registers
mtd: denali: Add multi connected NAND support
mtd: denali: Remove set_ecc_config function
mtd: denali: Remove unuseful code in get_xx_nand_para functions
mtd: denali: Remove device_info_tag structure
mtd: m25p80: add support for the Winbond W25Q32 SPI flash chip
mtd: m25p80: add support for the Intel/Numonyx {16,32,64}0S33B SPI flash chips
mtd: m25p80: add support for the EON EN25P{32, 64} SPI flash chips
...
Fix up trivial conflicts in drivers/mtd/maps/{Kconfig,redwood.c} due to
redwood driver removal.
There are three reasons to add this support:
1. users probably know the interface type of their flashs, then probe
can be faster if they give the right type in platform data since wrong
types will not be detected.
2. sometimes, detecting can cause destory to system. For example, for
kernel XIP, detecting can cause NOR enter a mode instructions can not
be fetched right, which will make kernel crash.
3. For a new probe which is not listed in the rom_probe_types, if users
assign it in board files, physmap can still probe it.
Signed-off-by: Barry Song <21cnbao@gmail.com>
Signed-off-by: Mike Frysinger <vapier.adi@gmail.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
The open and release block_device_operations are currently
called with the BKL held. In order to change that, we must
first make sure that all drivers that currently rely
on this have no regressions.
This blindly pushes the BKL into all .open and .release
operations for all block drivers to prepare for the
next step. The drivers can subsequently replace the BKL
with their own locks or remove it completely when it can
be shown that it is not needed.
The functions blkdev_get and blkdev_put are the only
remaining users of the big kernel lock in the block
layer, besides a few uses in the ioctl code, none
of which need to serialize with blkdev_{get,put}.
Most of these two functions is also under the protection
of bdev->bd_mutex, including the actual calls to
->open and ->release, and the common code does not
access any global data structures that need the BKL.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Christoph Hellwig <hch@infradead.org>
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
As a preparation for the removal of the big kernel
lock in the block layer, this removes the BKL
from the common ioctl handling code, moving it
into every single driver still using it.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Christoph Hellwig <hch@infradead.org>
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
Remove all the trivial wrappers for the cmd_type and cmd_flags fields in
struct requests. This allows much easier grepping for different request
types instead of unwinding through macros.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
Removing the redwood mtd mapping driver, because all REDWOOD_[456]
configuration options were removed from the kernel, because they weren't
referenced anywhere.
Signed-off-by: Christian Dietrich <qy03fugy@stud.informatik.uni-erlangen.de>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
* git://git.kernel.org/pub/scm/linux/kernel/git/brodo/pcmcia-2.6:
pcmcia: avoid buffer overflow in pcmcia_setup_isa_irq
pcmcia: do not request windows if you don't need to
pcmcia: insert PCMCIA device resources into resource tree
pcmcia: export resource information to sysfs
pcmcia: use struct resource for PCMCIA devices, part 2
pcmcia: remove memreq_t
pcmcia: move local definitions out of include/pcmcia/cs.h
pcmcia: do not use io_req_t when calling pcmcia_request_io()
pcmcia: do not use io_req_t after call to pcmcia_request_io()
pcmcia: use struct resource for PCMCIA devices
pcmcia: clean up cs.h
pcmcia: use pcmica_{read,write}_config_byte
pcmcia: remove cs_types.h
pcmcia: remove unused flag, simplify headers
pcmcia: remove obsolete CS_EVENT_ definitions
pcmcia: split up central event handler
pcmcia: simplify event callback
pcmcia: remove obsolete ioctl
Conflicts in:
- drivers/staging/comedi/drivers/*
- drivers/staging/wlags49_h2/wl_cs.c
due to dev_info_t and whitespace changes
Nand devices with at least 26 bytes of oob data per 512 byte block
can have 8bit ecc on v2 type controllers. This is currently not tested,
but at least this patch puts the ECC_MODE bit into a well defined state.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
The v2 controller has a totally different mechanism to check
whether the data we read had ecc errors or not. Implement this.
The mechanism in the v2 controller happens to be identical to
the v3 controller.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
This prepares the driver for v3 support. The v3 controller
has a completely different register layout, so add a V1_V2_
namespace to the register defines to avoid confusion with
the v3 regs.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
This patch prepares the driver to add v3 controller support
later. The v3 controller is basically the same controller as v1
and v2, but with a completely different register layout.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
We save/restore the value in the buffer anyway, so it makes
no difference whether we use main_area0 or main_area1. So,
we can use main_area0 and remove main_area1 from the driver
which is otherwise unused. Also, clean up the comments in
get_dev_status.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Add the offset to the register base instead. This is done
in preparation for v3 controller support.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
set_ecc_config function only set ECC_CORRECTION register, so
move register setting to probe function.
Since controller only support 15bit and 8bit ecc correction,
updated nand ecc layout information.
Signed-off-by: Chuanxiao Dong <chuanxiao.dong@intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Hi David,
I sent 4 patches using my intel email account. If there is any
problem about the format of these patches, I will resend them after
I arrived at home by using my gmail account, and I will keep on
using gmail account to send patches.
Thanks.
>From 242e3bf5e17f54b1df8cf285154a7c7a61ff62e9 Mon Sep 17 00:00:00 2001
From: Chuanxiao Dong <chuanxiao.dong@intel.com>
Date: Fri, 6 Aug 2010 15:29:41 +0800
Subject: [PATCH 1/4] mtd: denali: Remove device_info_tag structure.
Most of the variables in this structure are useless, so just
remove this structure and relevant codes.
Signed-off-by: Chuanxiao Dong <chuanxiao.dong@intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
of_device is just an alias for platform_device, so remove it entirely. Also
replace to_of_device() with to_platform_device() and update comment blocks.
This patch was initially generated from the following semantic patch, and then
edited by hand to pick up the bits that coccinelle didn't catch.
@@
@@
-struct of_device
+struct platform_device
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Reviewed-by: David S. Miller <davem@davemloft.net>
The Spansion S29WS-P device family uses CFI version 1.4 [1].
Consider it as a valid version.
[1] http://www.spansion.com/Support/Datasheets/s29ws-p_00_a12_e.pdf
Signed-off-by: Guillaume LECERF <glecerf@gmail.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Linus Torvalds