Pull MIPS updates from Ralf Baechle:
- Improvements to the tlb_dump code
- KVM fixes
- Add support for appended DTB
- Minor improvements to the R12000 support
- Minor improvements to the R12000 support
- Various platform improvments for BCM47xx
- The usual pile of minor cleanups
- A number of BPF fixes and improvments
- Some improvments to the support for R3000 and DECstations
- Some improvments to the ATH79 platform support
- A major patchset for the JZ4740 SOC adding support for the CI20 platform
- Add support for the Pistachio SOC
- Minor BMIPS/BCM63xx platform support improvments.
- Avoid "SYNC 0" as memory barrier when unlocking spinlocks
- Add support for the XWR-1750 board.
- Paul's __cpuinit/__cpuinitdata cleanups.
- New Malta CPU board support large memory so enable ZONE_DMA32.
* 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus: (131 commits)
MIPS: spinlock: Adjust arch_spin_lock back-off time
MIPS: asmmacro: Ensure 64-bit FP registers are used with MSA
MIPS: BCM47xx: Simplify handling SPROM revisions
MIPS: Cobalt Don't use module_init in non-modular MTD registration.
MIPS: BCM47xx: Move NVRAM driver to the drivers/firmware/
MIPS: use for_each_sg()
MIPS: BCM47xx: Don't select BCMA_HOST_PCI
MIPS: BCM47xx: Add helper variable for storing NVRAM length
MIPS: IRQ/IP27: Move IRQ allocation API to platform code.
MIPS: Replace smp_mb with release barrier function in unlocks.
MIPS: i8259: DT support
MIPS: Malta: Basic DT plumbing
MIPS: include errno.h for ENODEV in mips-cm.h
MIPS: Define GCR_GIC_STATUS register fields
MIPS: BPF: Introduce BPF ASM helpers
MIPS: BPF: Use BPF register names to describe the ABI
MIPS: BPF: Move register definition to the BPF header
MIPS: net: BPF: Replace RSIZE with SZREG
MIPS: BPF: Free up some callee-saved registers
MIPS: Xtalk: Update xwidget.h with known Xtalk device numbers
...
Multiple options depend on I2C but are already under under if I2C. Remove
those useless dependencies.
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Some entries in the Kconfig are improperly indented with spaces instead of
tabs.
Also fix whitespaces in Makefile.
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Gcc is unable to prove that alm_pending is always initialized
when it is used, so it prints a harmless warning:
drivers/rtc/rtc-pcf8563.c: In function 'pcf8563_probe':
drivers/rtc/rtc-pcf8563.c:449:5: warning: 'alm_pending' may be used uninitialized in this function [-Wmaybe-uninitialized]
This uses the same conditional expression that is used inside of
the pcf8563_get_alarm_mode() function, to help gcc figure it out
and shut up that warning, and make the ARM defconfigs build again
with no warnings.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Fixes: a45d528aab ("rtc: pcf8563: clear expired alarm at boot time")
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Alarm interrupt enable register is at offset 0x7, while the time
registers for the alarm follow that. When we program Alarm interrupt
enable prior to programming the time, it is possible that previous
time value could be close or match at the time of alarm enable
resulting in interrupt trigger which is unexpected (and does not match
the time we expect it to trigger).
To prevent this scenario from occuring, program the ALM0_EN bit only
after the alarm time is appropriately programmed.
Ofcourse, I2C programming is non-atomic, so there are loopholes where
the interrupt wont trigger if the time requested is in the past at
the time of programming the ALM0_EN bit. However, we will not have
unexpected interrupts while the time is programmed after the interrupt
are enabled.
Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Grygorii Strashko <grygorii.strashko@linaro.org>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Sometimes the irq line is not connected to any soc-pin. This does
not hinder basic timekeeping functionality of the rtc, so probe
should not fail in this case.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Use resource_size function on resource object instead of explicit
computation.
No need to set .owner here. The core will do it.
Remove .owner field if calls are used which set it automatically
Signed-off-by: Fengguang Wu <fengguang.wu@intel.com>
Acked-by: Hans Ulli Kroll <ulli.kroll@googlemail.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
The driver can't accommodate the 12 hour mode but the error message states
that the 24 hour mode is not supported.
Also fix the typos (hour vs hours).
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Use bit instead of hand coding the shift and correct the 24 hour vs 24
hours typo.
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
The rtc-efi driver declares that the EFI 'epoch' is 1/1/1998, but
the UEFI spec does not define it at all. It does define a range of
[1900, 9999] for the 'Year' member of the EFI_TIME struct, so let's
use 1900 as the minimum year and not 1998.
Also, move the validation of the year to the convert_from_efi_time()
routine where all other EFI_TIME fields are validated as well.
This prevents rtc_read_time() failures when the RTC that backs the
EFI time services is set to a date before 1998, e.g., when it has
lost power.
This also optimizes the compute_wday() routine, by replacing the for
loop with a simple arithmetic expression, and by reusing the yearday
value that we need to compute anyway when populating the
rtc_time::tm_yday field.
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Cc: rtc-linux@googlegroups.com
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Now rtc_set_mmss() has no users, just remove it.
We still have rtc_set_time() doing similar things.
Signed-off-by: Xunlei Pang <pang.xunlei@linaro.org>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Currently, CONFIG_RTC_SYSTOHC uses CONFIG_RTC_HCTOSYS_DEVICE which
is originally used by CONFIG_RTC_HCTOSYS, but this rtc device has
some limiations, for example, it must be battery-backed, be able
to work with irq off and through system suspension, etc.
So add CONFIG_RTC_SYSTOHC_DEVICE used exclusively for CONFIG_RTC_SYSTOHC,
it is more lenient compared to CONFIG_RTC_HCTOSYS_DEVICE, and could
be assigned any available RTC in the system.
Default value is CONFIG_RTC_HCTOSYS_DEVICE which is "rtc0" by default.
After this patch, NTP will sync up "rtc0" by default.
Cc: Paul Bolle <pebolle@tiscali.nl>
Signed-off-by: Xunlei Pang <pang.xunlei@linaro.org>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
sunxi_rtc_setalarm() uses deprecated rtc_tm_to_time(),
which will overflow in year 2106 on 32-bit machines.
This patch solves this by:
- Replacing rtc_tm_to_time() with rtc_tm_sub()
Also remove the unnecessary initial zeroing of some
local variables in sunxi_rtc_setalarm().
Cc: Carlo Caione <carlo.caione@gmail.com>
Signed-off-by: Xunlei Pang <pang.xunlei@linaro.org>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
isl1208_i2c_set_alarm() uses deprecated rtc_tm_to_time(),
which will overflow in year 2106 on 32-bit machines.
This patch solves this by:
- Replacing rtc_tm_to_time() with rtc_tm_sub()
Cc: Herbert Valerio Riedel <hvr@gnu.org>
Signed-off-by: Xunlei Pang <pang.xunlei@linaro.org>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
pcf8563_rtc_set_alarm() uses deprecated rtc_tm_to_time()
and rtc_time_to_tm(), which will overflow in year 2106
on 32-bit machines.
This patch solves this by:
- Replacing rtc_time_to_tm() with rtc_time64_to_tm()
- Replacing rtc_tm_to_time() with rtc_tm_to_time64()
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Xunlei Pang <pang.xunlei@linaro.org>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Initialise the variable high_bb_charging before using it to avoid
configuring wrong value and fix following compilation warning:
/*
rtc-palmas.c: In function ‘palmas_rtc_probe’:
rtc-palmas.c:242:7: warning: ‘high_bb_charging’ may be used
uninitialized in this function
*/
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Remove unneeded error handling on the result of a call to
platform_get_resource when the value is passed to devm_ioremap_resource.
Move the call to platform_get_resource adjacent to the call to
devm_ioremap_resource to make the connection between them more clear.
A simplified version of the semantic patch that makes this change is as
follows: (http://coccinelle.lip6.fr/)
// <smpl>
@@
expression pdev,res,n,e,e1;
expression ret != 0;
identifier l;
@@
- res = platform_get_resource(pdev, IORESOURCE_MEM, n);
... when != res
- if (res == NULL) { ... \(goto l;\|return ret;\) }
... when != res
+ res = platform_get_resource(pdev, IORESOURCE_MEM, n);
e = devm_ioremap_resource(e1, res);
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
[viresh.kumar@linaro.org: acked rtc-spear]
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Return -EINVAL if the voltage low bit is set to avoid getting a bogus
time at boot.
There was a comment stating that util-linux hwclock refuses to set a
new time if we return an error code on read, but at least the current
version do set the time as expected. Remove the comment and the check
for valid time, and let the rtc core check it for us.
Signed-off-by: Jan Kardell <jan.kardell@telliq.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Driver for the on chip RTC found on Cortina's SoC Gemini.
Signed-off-by: Hans Ulli Kroll <ulli.kroll@googlemail.com>
[alexandre.belloni@free-electrons.com: use devm_request_irq() and remove
useless goto]
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
When entering suspend while an wakeup alarm is set, enable_set_wake
should make sure that the RTC interrupt keep being enabled and the
.irq_set_wake for the RTC interrupt get called. However, since the
driver uses the suspend_noirq callback, the call to enable_irq_wake
has been made after disabling the interrupts. While .irq_set_wake
has been called properly, the interrupt remained disabled.
Use the suspend callback to call enable_irq_wake early enough to
ensure the RTC interrupt remains enabled.
Fixes: 7654e9d4fd ("drivers/rtc/rtc-snvs: fix suspend/resume")
Cc: <stable@vger.kernel.org> # 3.19
Signed-off-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Using gpio_request_array()/gpio_free_array() can make the code
simpler because it can set the direction and initial value
in one shot and the for loop is unnecessary.
Also, struct v3020_gpio is removed, because the struct v3020_gpio
is replaced with struct gpio.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Drivers should not be using the __raw_* io accessors.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
If the rtc-max77802 driver is built as a module, modalias information is
not filled so the module is not autoloaded. Use the MODULE_DEVICE_TABLE()
macro to export the platform ID table so the module contains that data.
Signed-off-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
If the rtc-max77686 driver is built as a module, modalias information is
not filled so the module is not autoloaded. Use the MODULE_DEVICE_TABLE()
macro to export the platform ID table so the module contains that data.
Signed-off-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
The device table is required to load modules based on modaliases.
After adding MODULE_DEVICE_TABLE, below entries will be added to
modules.alias:
alias i2c:ds1672 rtc_ds1672
alias i2c:max6900 rtc_max6900
alias platform:lp3974-rtc rtc_max8998
alias platform:max8998-rtc rtc_max8998
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: Dale Farnsworth <dale@farnsworth.org>
Cc: Minkyu Kang <mk7.kang@samsung.com>
Cc: Joonyoung Shim <jy0922.shim@samsung.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
On some !ARM 32bits platforms, the following compilation error happens
because of the division on a 64bits value in mtk_rtc_read_time():
drivers/built-in.o: In function `mtk_rtc_read_time':
rtc-mt6397.c:(.text+0x265d13f): undefined reference to `__divdi3'
rtc-mt6397.c:(.text+0x265d150): undefined reference to `__moddi3'
Use div_s64() as done in rtc_time64_to_tm() to solve that.
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Acked-by: Eddie Huang <eddie.huang@mediatek.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
According to C99, %2.s means 'print two spaces' (a precision of
. without following digits or * means 0). The kernel's printf
implementation, however, treats that case as if no precision was
given, but relying on that quirk is rather silly. Also, since no -
(aka left-justify) flag is given, the field with of 2 would then cause
the alarm->enabled case to come out as "o n". Deobfuscate it.
Signed-off-by: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
This patch updates the email address of the rtc-at32ap700x driver supported by
me to an email account I will use on a more regular basis in the future.
Signed-off-by: Hans-Christian Egtvedt <hans-christian.egtvedt@atmel.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Currently, code of Loongson-2/3 is under loongson directory and code of
Loongson-1 is under loongson1 directory. Besides, there are Kconfig
options such as MACH_LOONGSON and MACH_LOONGSON1. This naming style is
very ugly and confusing. Since Loongson-2/3 are both 64-bit general-
purpose CPU while Loongson-1 is 32-bit SoC, we rename both file names
and Kconfig symbols from loongson/loongson1 to loongson64/loongson32.
[ralf@linux-mips.org: Resolve a number of simple conflicts.]
Signed-off-by: Huacai Chen <chenhc@lemote.com>
Cc: Steven J. Hill <Steven.Hill@imgtec.com>
Cc: linux-mips@linux-mips.org
Cc: Fuxin Zhang <zhangfx@lemote.com>
Cc: Zhangjin Wu <wuzhangjin@gmail.com>
Cc: Kelvin Cheung <keguang.zhang@gmail.com>
Patchwork: https://patchwork.linux-mips.org/patch/9790/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
If the DryICE unit is locked it is impossible to set the time. Provide an
error message for this case.
Signed-off-by: Juergen Borleis <jbe@pengutronix.de>
Signed-off-by: Robert Schwebel <rsc@pengutronix.de>
[rsc: got NDA clearance from Freescale]
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Maybe the unit enters the hardware related state at runtime and not at
system boot time (after a power cycle).
Signed-off-by: Juergen Borleis <jbe@pengutronix.de>
Signed-off-by: Robert Schwebel <rsc@pengutronix.de>
[rsc: got NDA clearance from Freescale]
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
This code is required to recover the unit from a security violation.
Hopefully this code can recover the unit from a hardware related invalid
state as well.
Signed-off-by: Juergen Borleis <jbe@pengutronix.de>
Signed-off-by: Robert Schwebel <rsc@pengutronix.de>
[rsc: got NDA clearance from Freescale]
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Be independent of the endianness of the kernel.
Signed-off-by: Juergen Borleis <jbe@pengutronix.de>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
There are now no differences between RTC on Exynos3250 and S3C6410.
Merge everything into one so duplicated code could be removed.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Reviewed-by: Chanwoo Choi <cw00.choi@samsung.com>
Acked-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Reviewed-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Signed-off-by: Krzysztof Kozlowski <k.kozlowski.k@gmail.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
The rtc_timer_cancel() always returns 0 and cannot fail (calls only
other void-returning functions).
Signed-off-by: Krzysztof Kozlowski <k.kozlowski.k@gmail.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
The platform_device_id is not modified by the driver and core uses it as
const.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski.k@gmail.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
The platform_device_id is not modified by the driver and core uses it as
const.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski.k@gmail.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
The platform_device_id is not modified by the driver and core uses it as
const.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski.k@gmail.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
While setting the time, the RTC TIME register should not be accessed.
However due to hardware constraints, setting the RTC time involves
sleeping during 100ms. This sleep was done outside the critical section
protected by the spinlock, so it was possible to read the RTC TIME
register and get an incorrect value. This patch introduces a mutex for
protecting the RTC TIME access, unlike the spinlock it is allowed to
sleep in a critical section protected by a mutex.
The RTC STATUS register can still be used from the interrupt handler but
it has no effect on setting the time.
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Acked-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Acked-by: Andrew Lunn <andrew@lunn.ch>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: <stable@vger.kernel.org> [4.0]
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This is a basic driver for the ultra-low-power Abracon AB x80x series of RTC
chips. It supports in particular, the supersets AB0805 and AB1805.
It allows reading and writing the time, and enables the supercapacitor/
battery charger.
[arnd@arndb.de: abx805 depends on i2c]
[alexandre.belloni@free-electrons.com: renam buffer from date to buf in abx80x_rtc_read_time()]
Signed-off-by: Philippe De Muyter <phdm@macqel.be>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Cc: Paul Bolle <pebolle@tiscali.nl>
Cc: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
ST's Low Power Controller (LPC) controls two devices; watchdog and RTC.
Only one of the devices can be used at any one time. This is enforced
by the correlating MFD driver. This portion of the driver-set controls
the Real Time Clock.
Cc: Alessandro Zummo <a.zummo@towertech.it>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Change the __raw IO calls to readl/write_relaxed which makes the driver
endian agnostic to run properly on big endian systems.
Signed-off-by: Ben Dooks <ben.dooks@codethink.co.uk>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: Andrew Victor <linux@maxim.org.za>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The RTC driver supports two flavors of S5M devices: S5M8767-like and
S2MPS14-like.
On S2MPS13 and S2MPS14 devices the RTC module is the same so we want to
re-use the existing support of S2MPS14. However device type was passed
from parent MFD driver in platform data structure. This way for the
S2MPS13 device the main MFD driver passed device type of 'S2MPS13X'.
Instead decouple detecting of device type between main MFD and RTC driver.
This allows adding support for other S2MPS14 variations (like S2MPS11 and
S2MPS13) easily by adding to mfd/sec-core.c:
static const struct mfd_cell s2mps13_devs[] = {
{ .name = "s2mps14-rtc", }
};
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: Kyungmin Park <kyungmin.park@samsung.com>
Cc: Marek Szyprowski <m.szyprowski@samsung.com>
Cc: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The hym8563 datasheet describes the clock output control-bit as "when set
to logic 0, the square wave output is enable, when set to logic 1, the
CLKOUT output is inhibited". But in reality the setting is exactly
opposite.
Before now, the clock output was not really used, but on the rk3288 soc
this generated clock is used to supply the temperature sensor block and
the swapped bit value prevented it from working. With the corrected
value, the tsadc now reports correct values.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Acked-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
s3c_rtc_gettime() already returns the result of rtc_valid_tm() on the
obtained time so get rid of another call to rtc_valid_tm().
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Reviewed-by: Chanwoo Choi <cw00.choi@samsung.com>
Cc: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
RTC is present in AM43xx and DRA7xx also. Updating the Kconfig to depend
on ARCH_OMAP or ARCH_DAVINCI
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Acked-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: Paul Walmsley <paul@pwsan.com>
Cc: Tero Kristo <t-kristo@ti.com>
Cc: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
RTC module contains a kicker mechanism to prevent any spurious writes from
changing the register values. This mechanism requires two MMR writes to
the KICK0 and KICK1 registers with exact data values before the kicker
lock mechanism is released.
Currently the driver release the lock in the probe and leaves it enabled
until the rtc driver removal. This eliminates the idea of preventing
spurious writes when RTC driver is loaded. So implement rtc lock and
unlock functions before and after register writes.
This is as advised by Paul to implement lock and unlock functions in the
driver and not to unlock and leave it in probe. The same discussion can
be seen here:
http://www.mail-archive.com/linux-omap%40vger.kernel.org/msg111588.html
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Acked-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: Paul Walmsley <paul@pwsan.com>
Cc: Tero Kristo <t-kristo@ti.com>
Cc: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Use function name in the error log instead of __FILE__.
Signed-off-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Cc: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
__rtc_read_time logs should be debug logs instead of error logs.
For example, when the RTC clock is not set, it's not really useful
to print a kernel error log every time someone tries to read the clock:
~ # hwclock -r
[ 604.508263] rtc rtc0: read_time: fail to read
hwclock: RTC_RD_TIME: Invalid argument
If there's a real error, it's likely that lower level or higher level
code will tell it anyway. Make these logs debug logs, and also print
the error code for the read failure.
Signed-off-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Acked-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
In some error cases RTC name is used before it is initialized:
rtc-rs5c372 0-0032: clock needs to be set
rtc-rs5c372 0-0032: rs5c372b found, 24hr, driver version 0.6
rtc (null): read_time: fail to read
rtc-rs5c372 0-0032: rtc core: registered rtc-rs5c372 as rtc0
Fix by initializing the name early.
Signed-off-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Acked-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The S2MPS13 RTC is almost the same as S2MPS14. The differences when
updating alarm are:
1. Set WUDR+AUDR field instead of WUDR+RUDR.
2. Clear the AUDR field later (it is not auto-cleared).
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Cc: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add driver for the RTC hardware block on the Conexant CX92755 SoC, from
the Digicolor series of SoCs. Tested on the Equinox evaluation board for
the CX92755 chip.
[akpm@linux-foundation.org: build command arrays at compile-time]
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
When the clock is disabled, do not return a rate of 0 but instead return
the rate the clock will be running at after it gets enabled. This
prevents problems when the core clock code is trying to determine a
suitable rate, while the clock is still off.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The RTC is in a different clock domain so a quick read after write
can retrieve a mangled value of the old/new values
Signed-off-by: Adam Ward <adam.ward.opensource@diasemi.com>
Tested-by: Adam Ward <adam.ward.opensource@diasemi.com>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fix two minor sparse warnings:
CHECK drivers/rtc/rtc-ds1685.c
drivers/rtc/rtc-ds1685.c:2178:1: warning: function 'ds1685_rtc_poweroff' with external linkage has definition
drivers/rtc/rtc-ds1685.c:802:23: warning: Using plain integer as NULL pointer
Fixes: aaaf5fbf56 ("rtc: add driver for DS1685 family of real time clocks")
Signed-off-by: Joshua Kinard <kumba@gentoo.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The rtc driver core now sets the platform_driver 'owner' property, so
remove the assignment from the DS1685 driver.
Fixes: aaaf5fbf56f1: "rtc: add driver for DS1685 family of real time clocks"
Signed-off-by: Joshua Kinard <kumba@gentoo.org>
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The regmap_config struct may be const because it is not modified by the
driver and regmap_init() accepts pointer to const.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The current functions in s3c-rtc driver execute clk_enable/disable() to
control clocks and some functions execute s3c_rtc_alarm_clk_enable()
unnecessarily. So this patch deletes the duplicate clock control and
spilts s3c_rtc_alarm_clk_enable() out as
s3c_rtc_enable_clk()/s3c_rtc_disable_clk() to improve readability.
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: Kukjin Kim <kgene@kernel.org>
Cc: Inki Dae <inki.dae@samsung.com>
Cc: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
When using device trees on the ARM platform, it is not certain at compile
time whether or not the system will have a RTC.
If one enables CONFIG_HCTOSYS just in case the system booted has a RTC,
and it turns out not to be, this will result in a big fat "unable to open
rtc device" error being printed to console, even when "quiet" is set in
the kernel cmdline.
Fix this by outputting the message with loglevel info instead.
Signed-off-by: Floris Bos <bos@je-eigen-domein.nl>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Despite its name, sign_extend32() is safe to use for 8 bit types too.
(See https://lkml.org/lkml/2015/1/18/289).
Signed-off-by: Martin Kepplinger <martink@posteo.de>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Set the of_match_table for this driver so that devices can be described in
the device tree. This device is used in the Trimslice and is already
defined in the Trimslice device tree.
Signed-off-by: Peter Robinson <pbrobinson@gmail.com>
Cc: Mike Rapoport <mike@compulab.co.il>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: Grant Likely <grant.likely@linaro.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The rtc's status register allows to determine if a 32k crystal is
connected to keep the rtc running in low power states provided the
corresponding fuse bits were blown correctly during production. (In case
they were not, the right frequency can be stated in the device tree.) If
there is no such crystal available force the 24 MHz XTAL clock to keep
running to retain the right date and time. Otherwise use the crystal to
save some power.
It would be nice to only switch to the crystal when the XTAL clock is
about to be disabled and keep the crystal off when unneeded because XTAL
is always on while the chip is powered on. But as sudden power loss isn't
detectable this is not save.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This commit does not change any logic here. It just makes the code easier
to read.
This is how it looked like:
If err != 0 return err;
else return 0;
Signed-off-by: Robert Kmiec <robert.r.kmiec@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The seq_printf return value, because it's frequently misused,
will eventually be converted to void.
See: commit 1f33c41c03 ("seq_file: Rename seq_overflow() to
seq_has_overflowed() and make public")
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Pull HID updates from Jiri Kosina:
- quite a few firmware fixes for RMI driver by Andrew Duggan
- huion and uclogic drivers have been substantially overlaping in
functionality laterly. This redundancy is fixed by hid-huion driver
being merged into hid-uclogic; work done by Benjamin Tissoires and
Nikolai Kondrashov
- i2c-hid now supports ACPI GPIO interrupts; patch from Mika Westerberg
- Some of the quirks, that got separated into individual drivers, have
historically had EXPERT dependency. As HID subsystem matured (as
well as the individual drivers), this made less and less sense. This
dependency is now being removed by patch from Jean Delvare
- Logitech lg4ff driver received a couple of improvements for mode
switching, by Michal Malý
- multitouch driver now supports clickpads, patches by Benjamin
Tissoires and Seth Forshee
- hid-sensor framework received a substantial update; namely support
for Custom and Generic pages is being added; work done by Srinivas
Pandruvada
- wacom driver received substantial update; it now supports
i2c-conntected devices (Mika Westerberg), Bamboo PADs are now
properly supported (Benjamin Tissoires), much improved battery
reporting (Jason Gerecke) and pen proximity cleanups (Ping Cheng)
- small assorted fixes and device ID additions
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/hid: (68 commits)
HID: sensor: Update document for custom sensor
HID: sensor: Custom and Generic sensor support
HID: debug: fix error handling in hid_debug_events_read()
Input - mt: Fix input_mt_get_slot_by_key
HID: logitech-hidpp: fix error return code
HID: wacom: Add support for Cintiq 13HD Touch
HID: logitech-hidpp: add a module parameter to keep firmware gestures
HID: usbhid: yet another mouse with ALWAYS_POLL
HID: usbhid: more mice with ALWAYS_POLL
HID: wacom: set stylus_in_proximity before checking touch_down
HID: wacom: use wacom_wac_finger_count_touches to set touch_down
HID: wacom: remove hardcoded WACOM_QUIRK_MULTI_INPUT
HID: pidff: effect can't be NULL
HID: add quirk for PIXART OEM mouse used by HP
HID: add HP OEM mouse to quirk ALWAYS_POLL
HID: wacom: ask for a in-prox report when it was missed
HID: hid-sensor-hub: Fix sparse warning
HID: hid-sensor-hub: fix attribute read for logical usage id
HID: plantronics: fix Kconfig default
HID: pidff: support more than one concurrent effect
...
If a system does not provide a persistent_clock(), the time
will be updated on resume by rtc_resume(). With the addition
of the non-stop clocksources for suspend timing, those systems
set the time on resume in timekeeping_resume(), but may not
provide a valid persistent_clock().
This results in the rtc_resume() logic thinking no one has set
the time and it then will over-write the suspend time again,
which is not necessary and only increases clock error.
So, fix this for rtc_resume().
This patch also improves the name of persistent_clock_exist to
make it more grammatical.
Signed-off-by: Xunlei Pang <pang.xunlei@linaro.org>
Signed-off-by: John Stultz <john.stultz@linaro.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Link: http://lkml.kernel.org/r/1427945681-29972-19-git-send-email-john.stultz@linaro.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
rtc_read_time() has already judged valid tm by rtc_valid_tm(),
so just remove it.
Signed-off-by: Xunlei Pang <pang.xunlei@linaro.org>
Signed-off-by: John Stultz <john.stultz@linaro.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Link: http://lkml.kernel.org/r/1427945681-29972-17-git-send-email-john.stultz@linaro.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
This driver has a number of y2038/y2106 issues.
This patch resolves them by:
- Replacing rtc_time_to_tm() with rtc_time64_to_tm()
- Replacing rtc_tm_to_time() with rtc_tm_to_time64()
- Changing mxc_rtc_set_mmss() to use rtc_class_ops's set_mmss64()
After this patch, the driver should not have any remaining
y2038/y2106 issues.
Signed-off-by: Xunlei Pang <pang.xunlei@linaro.org>
Signed-off-by: John Stultz <john.stultz@linaro.org>
Acked-by: Alessandro Zummo <a.zummo@towertech.it>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Link: http://lkml.kernel.org/r/1427945681-29972-14-git-send-email-john.stultz@linaro.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
We want to convert mxc_rtc_set_mmss() to use rtc_class_ops's
set_mmss64(), but it uses get_alarm_or_time()/set_alarm_or_time()
internal interfaces which are y2038 unsafe.
So here as a separate patch, it converts these two internal
interfaces of "mxc" to use safe time64_t to make some
preparations.
Signed-off-by: Xunlei Pang <pang.xunlei@linaro.org>
Signed-off-by: John Stultz <john.stultz@linaro.org>
Acked-by: Alessandro Zummo <a.zummo@towertech.it>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Link: http://lkml.kernel.org/r/1427945681-29972-13-git-send-email-john.stultz@linaro.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
rtc_class_ops's set_alarm() shouldn't deal with the alarm date,
as this is handled in the rtc core.
See rtc_dev_ioctl()'s RTC_ALM_SET and RTC_WKALM_SET cases.
Signed-off-by: Xunlei Pang <pang.xunlei@linaro.org>
Signed-off-by: John Stultz <john.stultz@linaro.org>
Acked-by: Alessandro Zummo <a.zummo@towertech.it>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Link: http://lkml.kernel.org/r/1427945681-29972-12-git-send-email-john.stultz@linaro.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
This driver has a number of y2038/y2106 issues.
This patch resolves them by:
- Replacing rtc_time_to_tm() with rtc_time64_to_tm()
- Changing mc13xxx_rtc_set_mmss() to use rtc_class_ops's set_mmss64()
After this patch, the driver should not have any remaining
y2038/y2106 issues.
Signed-off-by: Xunlei Pang <pang.xunlei@linaro.org>
Signed-off-by: John Stultz <john.stultz@linaro.org>
Acked-by: Alessandro Zummo <a.zummo@towertech.it>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Link: http://lkml.kernel.org/r/1427945681-29972-11-git-send-email-john.stultz@linaro.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
This driver has a number of y2038/y2106 issues.
This patch resolves them by:
- Replacing rtc_tm_to_time() with rtc_tm_to_time64()
- Replacing rtc_time_to_tm() with rtc_time64_to_tm()
- Changing ab3100_rtc_set_mmss() to use rtc_class_ops's set_mmss64()
After this patch, the driver should not have any remaining
y2038/y2106 issues.
Signed-off-by: Xunlei Pang <pang.xunlei@linaro.org>
Signed-off-by: John Stultz <john.stultz@linaro.org>
Acked-by: Alessandro Zummo <a.zummo@towertech.it>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Link: http://lkml.kernel.org/r/1427945681-29972-10-git-send-email-john.stultz@linaro.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
This driver has a number of y2038/y2106 issues.
This patch resolves them by:
- Replacing get_seconds() with ktime_get_real_seconds()
- Replacing rtc_time_to_tm() with rtc_time64_to_tm()
Also add test_rtc_set_mmss64() for testing rtc_class_ops's
set_mmss64(), which can be activated by "test_mmss64" module
parameter.
Signed-off-by: Xunlei Pang <pang.xunlei@linaro.org>
Signed-off-by: John Stultz <john.stultz@linaro.org>
Acked-by: Alessandro Zummo <a.zummo@towertech.it>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Link: http://lkml.kernel.org/r/1427945681-29972-9-git-send-email-john.stultz@linaro.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Currently the rtc_class_op's set_mmss() function takes a 32-bit
second value (on 32-bit systems), which is problematic for dates
past y2038.
This patch provides a safe version named set_mmss64() using
y2038 safe time64_t.
After this patch, set_mmss() is deprecated and all its users
will be fixed to use set_mmss64(), it can be removed when having
no users.
Signed-off-by: Xunlei Pang <pang.xunlei@linaro.org>
[jstultz: Add whitespace fix for checkpatch]
Signed-off-by: John Stultz <john.stultz@linaro.org>
Acked-by: Alessandro Zummo <a.zummo@towertech.it>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Link: http://lkml.kernel.org/r/1427945681-29972-8-git-send-email-john.stultz@linaro.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
As part of addressing in-kernel y2038 issues, this patch adds
update_persistent_clock64() and replaces all the call sites of
update_persistent_clock() with this function. This is a __weak
implementation, which simply calls the existing y2038 unsafe
update_persistent_clock().
This allows architecture specific implementations to be
converted independently, and eventually y2038-unsafe
update_persistent_clock() can be removed after all its
architecture specific implementations have been converted to
update_persistent_clock64().
Suggested-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Xunlei Pang <pang.xunlei@linaro.org>
Signed-off-by: John Stultz <john.stultz@linaro.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Link: http://lkml.kernel.org/r/1427945681-29972-4-git-send-email-john.stultz@linaro.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
The Moorestown RTC driver implements suspend and resume callbacks and
assigns them to the suspend and resume fields of the device_driver
struct. These callbacks are never actually called by anything though.
Modify the driver to properly use dev_pm_ops so that the suspend and
resume functions are actually executed upon suspend/resume.
[akpm@linux-foundation.org: device_driver.name is const char *]
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: Feng Tang <feng.tang@intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
There is a typo here so we deadlock.
Fixes: dd1f1f391d ('rtc: at91rm9200: rework wakeup and interrupt handling')
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Reported-by: David Dueck <davidcdueck@googlemail.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Commit df9e26d093 ("rtc: s3c: add support for RTC of Exynos3250 SoC")
added an "rtc_src" DT property to specify the clock used as a source to
the S3C real-time clock.
Not all SoCs needs this so commit eaf3a65908 ("drivers/rtc/rtc-s3c.c:
fix initialization failure without rtc source clock") changed to check
the struct s3c_rtc_data .needs_src_clk to conditionally grab the clock.
But that commit didn't update the data for each IP version so the RTC
broke on the boards that needs a source clock. This is the case of at
least Exynos5250 and Exynos5440 which uses the s3c6410 RTC IP block.
This commit fixes the S3C rtc on the Exynos5250 Snow and Exynos5420
Peach Pit and Pi Chromebooks.
Signed-off-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Cc: Marek Szyprowski <m.szyprowski@samsung.com>
Cc: Chanwoo Choi <cw00.choi@samsung.com>
Cc: Doug Anderson <dianders@chromium.org>
Cc: Olof Johansson <olof@lixom.net>
Cc: Kevin Hilman <khilman@linaro.org>
Cc: Tyler Baker <tyler.baker@linaro.org>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The IRQ line used by the RTC device is usually shared with the system
timer (PIT) on at91 platforms.
Since timers are registering their handlers with IRQF_NO_SUSPEND, we
should expect being called in suspended state, and properly wake the
system up when this is the case.
Set IRQF_COND_SUSPEND flag when registering the IRQ handler to inform
irq core that it can safely be called while the system is suspended.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Reviewed-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The IRQ line used by the RTC device is usually shared with the system timer
(PIT) on at91 platforms.
Since timers are registering their handlers with IRQF_NO_SUSPEND, we should
expect being called in suspended state, and properly wake the system up
when this is the case.
Set IRQF_COND_SUSPEND flag when registering the IRQ handler to inform
irq core that it can safely be called while the system is suspended.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Reviewed-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The WTSR (Watchdog Timer Software Reset) and SMPL (Sudden Momentary
Power Loss) are never enabled. These are left-overs from board files.
After removing them the driver's shutdown callback is empty so get rid
of it as well.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Fix a conditional statement checking for NULL in both
ds1685_rtc_sysfs_time_regs_show and ds1685_rtc_sysfs_time_regs_store
that was using a logical AND when it should be using a logical OR so
that we fail out of the function properly if the condition ever
evaluates to true.
Fixes: aaaf5fbf56 ("rtc: add driver for DS1685 family of real time clocks")
Signed-off-by: Joshua Kinard <kumba@gentoo.org>
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
drivers/rtc/rtc-ds1685.c: In function `ds1685_rtc_read_alarm':
drivers/rtc/rtc-ds1685.c:402: warning: comparison is always true due to limited range of data type
drivers/rtc/rtc-ds1685.c:409: warning: comparison is always true due to limited range of data type
drivers/rtc/rtc-ds1685.c:416: warning: comparison is always true due to limited range of data type
drivers/rtc/rtc-ds1685.c: In function `ds1685_rtc_set_alarm':
drivers/rtc/rtc-ds1685.c:475: warning: comparison is always true due to limited range of data type
drivers/rtc/rtc-ds1685.c:478: warning: comparison is always true due to limited range of data type
drivers/rtc/rtc-ds1685.c:481: warning: comparison is always true due to limited range of data type
u8 cannot contain a value larger than 0xff, hence drop the checks.
Wrapping the checks in unlikely() indicated some sense of humor, though ;-)
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Acked-by: Joshua Kinard <kumba@gentoo.org>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The newly added ds1685 driver causes a build error when enabled without
CONFIG_RTC_INTF_DEV:
drivers/rtc/rtc-ds1685.c:919:22: error: 'ds1685_rtc_alarm_irq_enable' undeclared here (not in a function)
.alarm_irq_enable = ds1685_rtc_alarm_irq_enable,
Apparently the driver was incorrectly changed to reflect the interface
change from 16380c153a ("RTC: Convert rtc drivers to use the
alarm_irq_enable method"), which removed the respective #ifdef from all
other rtc drivers.
This does the same change that was merged for the other drivers before and
removes the #ifdef, allowing the interrupts to be enabled through the
in-kernel rtc interface independent of the existence of /dev/rtc.
Fixes: aaaf5fbf56 ("rtc: add driver for DS1685 family of real time clocks")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Joshua Kinard <kumba@gentoo.org>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add additional flag to read in async mode. In this mode the caller will get
reply via registered callback for capture_sample. Callbacks can be registered
using sensor_hub_register_callback function. The usage id parameter of the
capture_sample can be matched with the usage id of the requested attribute.
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Acked-by: Jonathan Cameron <jic23@kernel.org>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Pull kconfig updates from Michal Marek:
"Yann E Morin was supposed to take over kconfig maintainership, but
this hasn't happened. So I'm sending a few kconfig patches that I
collected:
- Fix for missing va_end in kconfig
- merge_config.sh displays used if given too few arguments
- s/boolean/bool/ in Kconfig files for consistency, with the plan to
only support bool in the future"
* 'kconfig' of git://git.kernel.org/pub/scm/linux/kernel/git/mmarek/kbuild:
kconfig: use va_end to match corresponding va_start
merge_config.sh: Display usage if given too few arguments
kconfig: use bool instead of boolean for type definition attributes
This is a good healthy set of various code removals. Total net delta is 8100
lines removed.
Among the larger cleanups are:
- Removal of old Samsung S3C DMA infrastructure by Arnd
- Removal of the non-DT version of the 'lager' board by Magnus Damm
- General stale code removal on OMAP and Davinci by Rickard Strandqvist
- Removal of non-DT support on am3517 platforms by Tony Lindgren
... plus several other cleanups of various platforms across the board.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=tsjK
-----END PGP SIGNATURE-----
Merge tag 'cleanup-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC cleanups from Olof Johansson:
"This is a good healthy set of various code removals. Total net delta
is 8100 lines removed.
Among the larger cleanups are:
- Removal of old Samsung S3C DMA infrastructure by Arnd
- Removal of the non-DT version of the 'lager' board by Magnus Damm
- General stale code removal on OMAP and Davinci by Rickard Strandqvist
- Removal of non-DT support on am3517 platforms by Tony Lindgren
... plus several other cleanups of various platforms across the board"
* tag 'cleanup-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (47 commits)
ARM: sirf: drop redundant function and marco declaration
arm: omap: specify PMUs are for ARMv7 CPUs
arm: shmobile: specify PMUs are for ARMv7 CPUs
arm: iop: specify PMUs are for XScale CPUs
arm: pxa: specify PMUs are for XScale CPUs
arm: realview: specify PMU types
ARM: SAMSUNG: remove unused DMA infrastructure
ARM: OMAP3: Add back Kconfig option MACH_OMAP3517EVM for ASoC
ARM: davinci: Remove CDCE949 driver
ARM: at91: remove useless at91rm9200_set_type()
ARM: at91: remove useless at91rm9200_dt_initialize()
ARM: at91: move debug-macro.S into the common space
ARM: at91: remove useless at91_sysirq_mask_rtx
ARM: at91: remove useless config MACH_AT91SAM9_DT
ARM: at91: remove useless config MACH_AT91RM9200_DT
ARM: at91: remove unused mach/memory.h
ARM: at91: remove useless header file includes
ARM: at91: remove unneeded header file
rtc: at91/Kconfig: remove useless options
ARM: at91/Documentation: add a README for Atmel SoCs
...
This adds a driver for the Dallas/Maxim DS1685-family of RTC chips. It
supports the DS1685/DS1687, DS1688/DS1691, DS1689/DS1693, DS17285/DS17287,
DS17485/DS17487, and DS17885/DS17887 RTC chips. These chips are commonly
found in SGI O2 and SGI Octane systems. It was originally derived from a
driver patch submitted by Matthias Fuchs many years ago for use in
EPPC-405-UC modules, which also used these RTCs. In addition to the
time-keeping functions, this RTC also handles the shutdown mechanism of
the O2 and Octane and acts as a partial NVRAM for the boot PROMS in these
systems.
Verified on both an SGI O2 and an SGI Octane.
Signed-off-by: Joshua Kinard <kumba@gentoo.org>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
"isil" and "isl" prefixes are used at various locations inside the kernel
to reference Intersil corporation. This patch is part of a series fixing
those locations were "isl" is used in compatible strings to use the now
expected "isil" prefix instead (NASDAQ symbol for Intersil and most used
version). The old compatible string is kept for backward compatibility.
Signed-off-by: Arnaud Ebalard <arno@natisbad.org>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Pawel Moll <pawel.moll@arm.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Ian Campbell <ijc+devicetree@hellion.org.uk>
Cc: Kumar Gala <galak@codeaurora.org>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Stephen Warren <swarren@wwwdotorg.org>
Cc: Thierry Reding <thierry.reding@gmail.com>
Cc: Alexandre Courbot <gnurou@gmail.com>
Cc: Uwe Kleine-Knig <uwe@kleine-koenig.org>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: Peter Huewe <peter.huewe@infineon.com>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Mark Brown <broonie@kernel.org>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Darshana Padmadas <darshanapadmadas@gmail.com>
Cc: Grant Likely <grant.likely@linaro.org>
Cc: Rob Landley <rob@landley.net>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Guenter Roeck <linux@roeck-us.net>
Cc: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
Cc: Uwe Kleine-König <uwe@kleine-koenig.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
"isil" and "isl" prefixes are used at various locations inside the kernel
to reference Intersil corporation. This patch is part of a series fixing
those locations were "isl" is used in compatible strings to use the now
expected "isil" prefix instead (NASDAQ symbol for Intersil and most used
version). The old compatible string is kept for backward compatibility.
Signed-off-by: Arnaud Ebalard <arno@natisbad.org>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Pawel Moll <pawel.moll@arm.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Ian Campbell <ijc+devicetree@hellion.org.uk>
Cc: Kumar Gala <galak@codeaurora.org>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Stephen Warren <swarren@wwwdotorg.org>
Cc: Thierry Reding <thierry.reding@gmail.com>
Cc: Alexandre Courbot <gnurou@gmail.com>
Cc: Uwe Kleine-Knig <uwe@kleine-koenig.org>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: Peter Huewe <peter.huewe@infineon.com>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Mark Brown <broonie@kernel.org>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Darshana Padmadas <darshanapadmadas@gmail.com>
Cc: Grant Likely <grant.likely@linaro.org>
Cc: Rob Landley <rob@landley.net>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Guenter Roeck <linux@roeck-us.net>
Cc: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
Cc: Uwe Kleine-König <uwe@kleine-koenig.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The new mvebu SoCs come with a new RTC driver. This patch adds the
support for this new IP which is currently found in the Armada 38x
SoCs.
This RTC provides two alarms, but only the first one is used in the
driver. The RTC also allows using periodic interrupts.
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Reviewed-by: Arnaud Ebalard <arno@natisbad.org>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Andrew Lunn <andrew@lunn.ch>
Cc: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Cc: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Cc: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Cc: Maxime Ripard <maxime.ripard@free-electrons.com>
Cc: Boris BREZILLON <boris.brezillon@free-electrons.com>
Cc: Lior Amsalem <alior@marvell.com>
Cc: Tawfik Bayouk <tawfik@marvell.com>
Cc: Nadav Haklai <nadavh@marvell.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Abracon AB-RTCMC-32.768kHz-B5ZE-S3 alarm is only accurate to the minute.
For that reason, UIE mode is currently not supported by the driver. But
the device provides a watchdog timer which can be coupled with the alarm
mechanism to extend support and provide sub-minute alarm capability.
This patch implements that extension. More precisely, it makes use of the
watchdog timer for alarms which are less that four minutes in the future
(with second accuracy) and use standard alarm mechanism for other alarms
(with minute accuracy).
Signed-off-by: Arnaud Ebalard <arno@natisbad.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: Peter Huewe <peter.huewe@infineon.com>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Thierry Reding <treding@nvidia.com>
Cc: Mark Brown <broonie@kernel.org>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Rob Herring <robherring2@gmail.com>
Cc: Pawel Moll <pawel.moll@arm.com>
Cc: Stephen Warren <swarren@wwwdotorg.org>
Cc: Ian Campbell <ijc+devicetree@hellion.org.uk>
Cc: Grant Likely <grant.likely@linaro.org>
Cc: Rob Landley <rob@landley.net>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Guenter Roeck <linux@roeck-us.net>
Cc: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
Cc: Kumar Gala <galak@codeaurora.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch adds support for Abracon AB-RTCMC-32.768kHz-B5ZE-S3
RTC/Calendar module w/ I2C interface.
This support includes RTC time reading and setting, Alarm (1 minute
accuracy) reading and setting, and battery low detection. The device also
supports frequency adjustment and two timers but those features are
currently not implemented in this driver. Due to alarm accuracy
limitation (and current lack of timer support in the driver), UIE mode is
not supported.
Signed-off-by: Arnaud Ebalard <arno@natisbad.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: Peter Huewe <peter.huewe@infineon.com>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Thierry Reding <treding@nvidia.com>
Cc: Mark Brown <broonie@kernel.org>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Rob Herring <robherring2@gmail.com>
Cc: Pawel Moll <pawel.moll@arm.com>
Cc: Stephen Warren <swarren@wwwdotorg.org>
Cc: Ian Campbell <ijc+devicetree@hellion.org.uk>
Cc: Grant Likely <grant.likely@linaro.org>
Cc: Rob Landley <rob@landley.net>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Guenter Roeck <linux@roeck-us.net>
Cc: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
Cc: Kumar Gala <galak@codeaurora.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
After we set the GET_TIME bit, the rtc time can't be read immediately. We
should wait up to 31.25 us, about one cycle of 32khz. Otherwise reading
RTC time will return a old time. If we clear the GET_TIME bit after
setting, the time of i2c transfer is certainly more than 31.25us.
Doug said:
: I think we are safe. At 400kHz (the max speed of this part) each bit can
: be transferred no faster than 2.5us. In order to do a valid i2c
: transaction we need to _at least_ write the address of the device and the
: data onto the bus, which is 16 bits. 16 * 2.5us = 40us. That's above the
: 31.25us
[akpm@linux-foundation.org: tweak comment per review discussion]
Signed-off-by: Chris Zhong <zyw@rock-chips.com>
Reviewed-by: Doug Anderson <dianders@chromium.org>
Cc: Sonny Rao <sonnyrao@chromium.org>
Cc: Heiko Stübner <heiko@sntech.de>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The regmap_config struct may be const because it is not modified by the
driver and regmap_init() accepts pointer to const.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The regmap_config struct may be const because it is not modified by the
driver and regmap_init() accepts pointer to const.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Intended for monitoring and controlling the security features. These bits
are required to bring this unit back to live after a security violation
event was detected. The code to bring it back to live will follow after a
vendor clearance.
Signed-off-by: Juergen Borleis <jbe@pengutronix.de>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Current in-tree users of ISL12057 RTC chip (NETGEAR ReadyNAS 102, 104 and
2120) do not have the IRQ#2 pin of the chip (associated w/ the Alarm1
mechanism) connected to their SoC, but to a PMIC (TPS65251 FWIW). This
specific hardware configuration allows the NAS to wake up when the alarms
rings.
Recently introduced alarm support for ISL12057 relies on the provision of
an "interrupts" property in system .dts file, which previous three users
will never get. For that reason, alarm support on those devices is not
function. To support this use case, this patch adds a new DT property for
ISL12057 (isil,irq2-can-wakeup-machine) to indicate that the chip is
capable of waking up the device using its IRQ#2 pin (even though it does
not have its IRQ#2 pin connected directly to the SoC).
This specific configuration was tested on a ReadyNAS 102 by setting an
alarm, powering off the device and see it reboot as expected when the
alarm rang w/:
# echo `date '+%s' -d '+ 1 minutes'` > /sys/class/rtc/rtc0/wakealarm
# shutdown -h now
As a side note, the ISL12057 remains in the list of trivial devices,
because the property is not per se required by the device to work but can
help handle system w/ specific requirements. In exchange, the new feature
is described in details in a specific documentation file.
Signed-off-by: Arnaud Ebalard <arno@natisbad.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: Peter Huewe <peter.huewe@infineon.com>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Thierry Reding <treding@nvidia.com>
Cc: Mark Brown <broonie@kernel.org>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Darshana Padmadas <darshanapadmadas@gmail.com>
Cc: Rob Herring <rob.herring@calxeda.com>
Cc: Pawel Moll <pawel.moll@arm.com>
Cc: Stephen Warren <swarren@wwwdotorg.org>
Cc: Ian Campbell <ijc+devicetree@hellion.org.uk>
Cc: Grant Likely <grant.likely@linaro.org>
Cc: Rob Landley <rob@landley.net>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Guenter Roeck <linux@roeck-us.net>
Cc: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
Cc: Kumar Gala <galak@codeaurora.org>
Cc: Uwe Kleine-König <uwe@kleine-koenig.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch adds alarm support to Intersil ISL12057 driver. This allows to
configure the chip to generate an interrupt when the alarm matches current
time value. Alarm can be programmed up to one month in the future and is
accurate to the second.
The patch was developed to support two different configurations: systems
w/ and w/o RTC chip IRQ line connected to the main CPU.
The latter is the one found on current 3 kernel users of the chip for
which support was initially developed (Netgear ReadyNAS 102, 104 and 2120
NAS). On those devices, the IRQ#2 pin of the chip is not connected to the
SoC but to a PMIC. This allows setting an alarm, powering off the device
and have it wake up when the alarm rings. To support that configuration
the driver does the following:
1. it has alarm_irq_enable() function returns -ENOTTY when no IRQ
is passed to the driver.
2. it marks the device as a wakeup source in all cases (whether an
IRQ is passed to the driver or not) to have 'wakealarm' sysfs
entry created.
3. it marks the device has not supporting UIE mode when no IRQ is
passed to the driver (see the commmit message of c9f5c7e7a8)
This specific configuration was tested on a ReadyNAS 102 by setting an
alarm, powering off the device and see it reboot as expected when the
alarm rang.
The former configuration was tested on a Netgear ReadyNAS 102 after some
soldering of the IRQ#2 pin of the RTC chip to a MPP line of the SoC (the
one used usually handles the reset button). The test was performed using
a modified .dts file reflecting this change (see below) and rtc-test.c
program available in Documentation/rtc.txt. This test program ran as
expected, which validates alarm supports, including interrupt support.
As a side note, the ISL12057 remains in the list of trivial devices, i.e.
no specific DT binding being added by this patch: i2c core automatically
handles extraction of IRQ line info from .dts file. For instance, if one
wants to reference the interrupt line for the alarm in its .dts file,
adding interrupt and interrupt-parent properties works as expected:
isl12057: isl12057@68 {
compatible =3D "isil,isl12057";
interrupt-parent =3D <&gpio0>;
interrupts =3D <6 IRQ_TYPE_EDGE_FALLING>;
reg =3D <0x68>;
};
FWIW, if someone is looking for a way to test alarm support on a system on
which the chip IRQ line has the ability to boot the system (e.g. ReadyNAS
102, 104, etc):
# echo 0 > /sys/class/rtc/rtc0/wakealarm
# echo `date '+%s' -d '+ 1 minutes'` > /sys/class/rtc/rtc0/wakealarm
# shutdown -h now
With the commands above, after a minute, the system comes back to life.
Signed-off-by: Arnaud Ebalard <arno@natisbad.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: Peter Huewe <peter.huewe@infineon.com>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Thierry Reding <treding@nvidia.com>
Cc: Mark Brown <broonie@kernel.org>
Cc: Grant Likely <grant.likely@linaro.org>
Cc: Uwe Kleine-König <uwe@kleine-koenig.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Pull EFI updates from Ingo Molnar:
"Main changes:
- Move efivarfs from the misc filesystem section to pseudo filesystem
- Expose firmware platform size in sysfs
- Improve robustness of get_memory_map() by removing assumptions on
the size of efi_memory_desc_t.
- various cleanups and fixes
The biggest risk is the get_memory_map() change, which changes the way
that both the arm64 and x86 EFI boot stub build the early memory map.
There are no known regressions with it at the moment, BYMMV"
* 'x86-efi-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
efi: Don't look for chosen@0 node on DT platforms
firmware: efi: Remove unneeded guid unparse
efi/libstub: Call get_memory_map() to obtain map and desc sizes
efi: Small leak on error in runtime map code
efi: rtc-efi: Mark UIE as unsupported
arm64/efi: efistub: Apply __init annotation
efi: Expose underlying UEFI firmware platform size to userland
efi: Rename efi_guid_unparse to efi_guid_to_str
efi: Update the URLs for efibootmgr
fs: Make efivarfs a pseudo filesystem, built by default with EFI
Pull timer updates from Ingo Molnar:
"The main changes in this cycle were:
- rework hrtimer expiry calculation in hrtimer_interrupt(): the
previous code had a subtle bug where expiry caching would miss an
expiry, resulting in occasional bogus (late) expiry of hrtimers.
- continuing Y2038 fixes
- ktime division optimization
- misc smaller fixes and cleanups"
* 'timers-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
hrtimer: Make __hrtimer_get_next_event() static
rtc: Convert rtc_set_ntp_time() to use timespec64
rtc: Remove redundant rtc_valid_tm() from rtc_hctosys()
rtc: Modify rtc_hctosys() to address y2038 issues
rtc: Update rtc-dev to use y2038-safe time interfaces
rtc: Update interface.c to use y2038-safe time interfaces
time: Expose get_monotonic_boottime64 for in-kernel use
time: Expose getboottime64 for in-kernel uses
ktime: Optimize ktime_divns for constant divisors
hrtimer: Prevent stale expiry time in hrtimer_interrupt()
ktime.h: Introduce ktime_ms_delta
since that's a more logical and accurate place - Leif Lindholm
* Update efibootmgr URL in Kconfig help - Peter Jones
* Improve accuracy of EFI guid function names - Borislav Petkov
* Expose firmware platform size in sysfs for the benefit of EFI boot
loader installers and other utilities - Steve McIntyre
* Cleanup __init annotations for arm64/efi code - Ard Biesheuvel
* Mark the UIE as unsupported for rtc-efi - Ard Biesheuvel
* Fix memory leak in error code path of runtime map code - Dan Carpenter
* Improve robustness of get_memory_map() by removing assumptions on the
size of efi_memory_desc_t (which could change in future spec
versions) and querying the firmware instead of guessing about the
memmap size - Ard Biesheuvel
* Remove superfluous guid unparse calls - Ivan Khoronzhuk
* Delete unnecessary chosen@0 DT node FDT code since was duplicated
from code in drivers/of and is entirely unnecessary - Leif Lindholm
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=iPpM
-----END PGP SIGNATURE-----
Merge tag 'efi-next' of git://git.kernel.org/pub/scm/linux/kernel/git/mfleming/efi into x86/efi
Pull EFI updates from Matt Fleming:
" - Move efivarfs from the misc filesystem section to pseudo filesystem,
since that's a more logical and accurate place - Leif Lindholm
- Update efibootmgr URL in Kconfig help - Peter Jones
- Improve accuracy of EFI guid function names - Borislav Petkov
- Expose firmware platform size in sysfs for the benefit of EFI boot
loader installers and other utilities - Steve McIntyre
- Cleanup __init annotations for arm64/efi code - Ard Biesheuvel
- Mark the UIE as unsupported for rtc-efi - Ard Biesheuvel
- Fix memory leak in error code path of runtime map code - Dan Carpenter
- Improve robustness of get_memory_map() by removing assumptions on the
size of efi_memory_desc_t (which could change in future spec
versions) and querying the firmware instead of guessing about the
memmap size - Ard Biesheuvel
- Remove superfluous guid unparse calls - Ivan Khoronzhuk
- Delete unnecessary chosen@0 DT node FDT code since was duplicated
from code in drivers/of and is entirely unnecessary - Leif Lindholm
There's nothing super scary, mainly cleanups, and a merge from Ricardo who
kindly picked up some patches from the linux-efi mailing list while I
was out on annual leave in December.
Perhaps the biggest risk is the get_memory_map() change from Ard, which
changes the way that both the arm64 and x86 EFI boot stub build the
early memory map. It would be good to have it bake in linux-next for a
while.
"
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Array of platform_device_id elements should be terminated with empty
element.
Fixes: 5bccae6ec4 ("rtc: s5m-rtc: add real-time clock driver for s5m8767")
Signed-off-by: Andrey Ryabinin <a.ryabinin@samsung.com>
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
rtc_set_ntp_time() uses timespec which is y2038-unsafe,
so modify to use timespec64 which is y2038-safe, then
replace rtc_time_to_tm() with rtc_time64_to_tm().
Also adjust all its call sites(only NTP uses it) accordingly.
Cc: pang.xunlei <pang.xunlei@linaro.org>
Cc: Arnd Bergmann <arnd.bergmann@linaro.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Xunlei Pang <pang.xunlei@linaro.org>
Signed-off-by: John Stultz <john.stultz@linaro.org>
rtc_read_time() has already judged valid tm by rtc_valid_tm(),
so just remove it.
Cc: pang.xunlei <pang.xunlei@linaro.org>
Cc: Arnd Bergmann <arnd.bergmann@linaro.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Xunlei Pang <pang.xunlei@linaro.org>
Signed-off-by: John Stultz <john.stultz@linaro.org>
rtc_hctosys() has a number of y2038 issues.
This patch resolves them by:
- Replace rtc_tm_to_time() with y2038-safe rtc_tm_to_time64()
- Replace do_settimeofday() with y2038-safe do_settimeofday64()
After this patch, it should not have any remaining y2038 issues.
Cc: pang.xunlei <pang.xunlei@linaro.org>
Cc: Arnd Bergmann <arnd.bergmann@linaro.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Xunlei Pang <pang.xunlei@linaro.org>
Signed-off-by: John Stultz <john.stultz@linaro.org>
Currently, rtc-dev.c uses y2038 problematic rtc_tm_to_time()
and rtc_time_to_tm(). So replace them with their corresponding
y2038-safe versions: rtc_tm_to_time64() and rtc_time64_to_tm().
Cc: pang.xunlei <pang.xunlei@linaro.org>
Cc: Arnd Bergmann <arnd.bergmann@linaro.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Xunlei Pang <pang.xunlei@linaro.org>
Signed-off-by: John Stultz <john.stultz@linaro.org>
Currently, interface.c uses y2038 problematic rtc_tm_to_time()
and rtc_time_to_tm(). So replace them with their corresponding
y2038-safe versions: rtc_tm_to_time64() and rtc_time64_to_tm().
Cc: pang.xunlei <pang.xunlei@linaro.org>
Cc: Arnd Bergmann <arnd.bergmann@linaro.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Xunlei Pang <pang.xunlei@linaro.org>
Signed-off-by: John Stultz <john.stultz@linaro.org>
Tools like hwclock attempt to enable the RTC update interrupt (UIE) to
maximize the accuracy of the reported time value. The EFI rtc does not
have interrupt capability so this is a pointless exercise to begin with,
but the generic RTC framework ends up issuing a SetWakeupTime() Runtime
Services call before drawing that conclusion on its own.
Instead, we can mark UIE as unsupported at driver probe time. The net
result is the same, but without the spurious SetWakeupTime() call.
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Matt Fleming <matt.fleming@intel.com>
As we removed all the !DT boards during 3.19 cycle, we can now remove these
options.
Reported-by: Paul Bolle <pebolle@tiscali.nl>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Support for keyword 'boolean' will be dropped later on.
No functional change.
Reference: http://lkml.kernel.org/r/cover.1418003065.git.cj@linux.com
Signed-off-by: Christoph Jaeger <cj@linux.com>
Signed-off-by: Michal Marek <mmarek@suse.cz>
Here's the set of driver core patches for 3.19-rc1.
They are dominated by the removal of the .owner field in platform
drivers. They touch a lot of files, but they are "simple" changes, just
removing a line in a structure.
Other than that, a few minor driver core and debugfs changes. There are
some ath9k patches coming in through this tree that have been acked by
the wireless maintainers as they relied on the debugfs changes.
Everything has been in linux-next for a while.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iEYEABECAAYFAlSOD20ACgkQMUfUDdst+ylLPACg2QrW1oHhdTMT9WI8jihlHVRM
53kAoLeteByQ3iVwWurwwseRPiWa8+MI
=OVRS
-----END PGP SIGNATURE-----
Merge tag 'driver-core-3.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull driver core update from Greg KH:
"Here's the set of driver core patches for 3.19-rc1.
They are dominated by the removal of the .owner field in platform
drivers. They touch a lot of files, but they are "simple" changes,
just removing a line in a structure.
Other than that, a few minor driver core and debugfs changes. There
are some ath9k patches coming in through this tree that have been
acked by the wireless maintainers as they relied on the debugfs
changes.
Everything has been in linux-next for a while"
* tag 'driver-core-3.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core: (324 commits)
Revert "ath: ath9k: use debugfs_create_devm_seqfile() helper for seq_file entries"
fs: debugfs: add forward declaration for struct device type
firmware class: Deletion of an unnecessary check before the function call "vunmap"
firmware loader: fix hung task warning dump
devcoredump: provide a one-way disable function
device: Add dev_<level>_once variants
ath: ath9k: use debugfs_create_devm_seqfile() helper for seq_file entries
ath: use seq_file api for ath9k debugfs files
debugfs: add helper function to create device related seq_file
drivers/base: cacheinfo: remove noisy error boot message
Revert "core: platform: add warning if driver has no owner"
drivers: base: support cpu cache information interface to userspace via sysfs
drivers: base: add cpu_device_create to support per-cpu devices
topology: replace custom attribute macros with standard DEVICE_ATTR*
cpumask: factor out show_cpumap into separate helper function
driver core: Fix unbalanced device reference in drivers_probe
driver core: fix race with userland in device_add()
sysfs/kernfs: make read requests on pre-alloc files use the buffer.
sysfs/kernfs: allow attributes to request write buffer be pre-allocated.
fs: sysfs: return EGBIG on write if offset is larger than file size
...
Commit 7654e9d4fd ("drivers/rtc/rtc-snvs: fix suspend/resume")
replaces SIMPLE_DEV_PM_OPS with direct declaration of snvs_rtc_pm_ops,
but does so outside #ifdef CONFIG_PM_SLEEP. This causes the driver
build to fail if CONFIG_PM_SLEEP is not configured.
Fixes: 7654e9d4fd ("drivers/rtc/rtc-snvs: fix suspend/resume")
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Cc: Sanchayan Maity <maitysanchayan@gmail.com>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Some nice cleanups like removing bootmem, and removal of __get_cpu_var().
There is one patch to mm/gup.c. This is the generic GUP implementation, but is
only used by us and arm(64). We have an ack from Steve Capper, and although we
didn't get an ack from Andrew he told us to take the patch through the powerpc
tree.
There's one cxl patch. This is in drivers/misc, but Greg said he was happy for
us to manage fixes for it.
There is an infrastructure patch to support an IPMI driver for OPAL. That patch
also appears in Corey Minyard's IPMI tree, you may see a conflict there.
There is also an RTC driver for OPAL. We weren't able to get any response from
the RTC maintainer, Alessandro Zummo, so in the end we just merged the driver.
The usual batch of Freescale updates from Scott.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=jvyT
-----END PGP SIGNATURE-----
Merge tag 'powerpc-3.19-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mpe/linux
Pull powerpc updates from Michael Ellerman:
"Some nice cleanups like removing bootmem, and removal of
__get_cpu_var().
There is one patch to mm/gup.c. This is the generic GUP
implementation, but is only used by us and arm(64). We have an ack
from Steve Capper, and although we didn't get an ack from Andrew he
told us to take the patch through the powerpc tree.
There's one cxl patch. This is in drivers/misc, but Greg said he was
happy for us to manage fixes for it.
There is an infrastructure patch to support an IPMI driver for OPAL.
There is also an RTC driver for OPAL. We weren't able to get any
response from the RTC maintainer, Alessandro Zummo, so in the end we
just merged the driver.
The usual batch of Freescale updates from Scott"
* tag 'powerpc-3.19-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mpe/linux: (101 commits)
powerpc/powernv: Return to cpu offline loop when finished in KVM guest
powerpc/book3s: Fix partial invalidation of TLBs in MCE code.
powerpc/mm: don't do tlbie for updatepp request with NO HPTE fault
powerpc/xmon: Cleanup the breakpoint flags
powerpc/xmon: Enable HW instruction breakpoint on POWER8
powerpc/mm/thp: Use tlbiel if possible
powerpc/mm/thp: Remove code duplication
powerpc/mm/hugetlb: Sanity check gigantic hugepage count
powerpc/oprofile: Disable pagefaults during user stack read
powerpc/mm: Check for matching hpte without taking hpte lock
powerpc: Drop useless warning in eeh_init()
powerpc/powernv: Cleanup unused MCE definitions/declarations.
powerpc/eeh: Dump PHB diag-data early
powerpc/eeh: Recover EEH error on ownership change for BCM5719
powerpc/eeh: Set EEH_PE_RESET on PE reset
powerpc/eeh: Refactor eeh_reset_pe()
powerpc: Remove more traces of bootmem
powerpc/pseries: Initialise nvram_pstore_info's buf_lock
cxl: Name interrupts in /proc/interrupt
cxl: Return error to PSL if IRQ demultiplexing fails & print clearer warning
...
rtc_timer_do_work() only judges -ETIME failure of__rtc_set_alarm(), but
doesn't handle other failures like -EIO, -EBUSY, etc.
If there is a failure other than -ETIME, the next rtc_timer will stay in
the timerqueue. Then later rtc_timers will be enqueued directly because
they have a later expires time, so the alarm irq will never be programmed.
When such failures happen, this patch will retry __rtc_set_alarm(), if
still can't program the alarm time, it will remove current rtc_timer from
timerqueue and fetch next one, thus preventing it from affecting other rtc
timers.
Signed-off-by: Xunlei Pang <pang.xunlei@linaro.org>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: John Stultz <john.stultz@linaro.org>
Cc: Arnd Bergmann <arnd.bergmann@linaro.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Currently, ab8500 doesn't set uie_unsupported of rtc_device, while it
doesn't support UIE, see ab8500_rtc_set_alarm().
Thus, when going through rtc_update_irq_enable()->rtc_timer_enqueue(),
there's a chance it has an alarm timer1 queued before which is going to
fired, so this update timer2 will be queued because it isn't the leftmost
one, which means rtc_timer_enqueue() will return 0.
This will result in two problems:
1) UIE EMUL will not be used.
2) When the alarm timer1 is fired, in rtc_timer_do_work() timer2 will
fail to set the alarm time, so this rtc will disfunctional due to
timer2 with the earliest expires in the timerqueue.
So, rtc drivers must set this flag if they don't support UIE.
Signed-off-by: Xunlei Pang <pang.xunlei@linaro.org>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: John Stultz <john.stultz@linaro.org>
Cc: Arnd Bergmann <arnd.bergmann@linaro.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The alarm interrupt handler also reads registers which are part of SNVS
and need clocks enabled. However, the resume function is called after
IRQ's have been enabled, hence this leads to a abort:
Unhandled fault: external abort on non-linefetch (0x1008) at 0x908c604c
Internal error: : 1008 [#1] ARM
Modules linked in:
CPU: 0 PID: 421 Comm: sh Not tainted 3.18.0-rc5-00135-g0689c67-dirty #1592
task: 8e03e800 ti: 8cad8000 task.ti: 8cad8000
PC is at snvs_rtc_irq_handler+0x14/0x74
LR is at handle_irq_event_percpu+0x3c/0x144
Fix this by using the .{suspend/resume}_noirq callbacks instead of
.{suspend/resume} .
Signed-off-by: Sanchayan Maity <maitysanchayan@gmail.com>
Cc: Shawn Guo <shawn.guo@linaro.org>
Cc: Stefan Agner <stefan@agner.ch>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add clock enable and disable support for the SNVS peripheral, which is
required for using the RTC within the SNVS block.
The clock is not strictly enforced, as this would break the i.MX devices.
The clocking for the i.MX devices seems to be enabled elsewhere and
enabling RTC SNVS for Vybrid results in a crash. This patch adds the
clock support but also makes it optional so Vybrid platform can use the
clock if defined while making sure not to break i.MX.
Signed-off-by: Sanchayan Maity <maitysanchayan@gmail.com>
Cc: Shawn Guo <shawn.guo@linaro.org>
Acked-by: Stefan Agner <stefan@agner.ch>
Acked-by: Alessandro Zummo <a.zummo@towertech.it>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Drop the vendor-prefix from the "ti,system-power-controller" device-tree
property name.
It has been agreed to make "system-power-controller" a standard property
and to drop the vendor-prefix that is currently used by several drivers.
Note that drivers that have used "<vendor>,system-power-controller" in a
released kernel will need to support both versions.
Signed-off-by: Johan Hovold <johan@kernel.org>
Cc: Tony Lindgren <tony@atomide.com>
Cc: Benot Cousson <bcousson@baylibre.com>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: Felipe Balbi <balbi@ti.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
As pointed out by Mark, it is generally useful to log the error code when
reporting a failure. This patch improves existing calls to dev_err() in
ISL12057 driver to also report error code.
Signed-off-by: Arnaud Ebalard <arno@natisbad.org>
Suggested-by: Mark Brown <broonie@kernel.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: Peter Huewe <peter.huewe@infineon.com>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Thierry Reding <treding@nvidia.com>
Cc: Grant Likely <grant.likely@linaro.org>
Acked-by: Uwe Kleine-König <uwe@kleine-koenig.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
As suggested by Uwe, instead of clearing oscillator failure bit
unconditionally at driver load, this patch adds proper handling of the
flag. The driver now returns -ENODATA when reading time from the device
and oscillator failure bit is set. The flag is now cleared only when the
a new time value is pushed to the device.
Signed-off-by: Arnaud Ebalard <arno@natisbad.org>
Reported-by: Uwe Kleine-König <uwe@kleine-koenig.org>
Acked-by: Uwe Kleine-König <uwe@kleine-koenig.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: Peter Huewe <peter.huewe@infineon.com>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Thierry Reding <treding@nvidia.com>
Cc: Mark Brown <broonie@kernel.org>
Cc: Grant Likely <grant.likely@linaro.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The month register of ISL12057 RTC chip includes a century bit which
reports overflow of year register from 99 to 0. This bit can also be
written, which allows using it to extend the time interval the chip can
support from 99 to 199 years.
This patch adds support for century overflow bit in tm to regs and regs to
tm helpers in ISL12057 driver.
This was tested by putting a device 100 years in the future (using a
specific kernel due to the inability of userland tools such as date or
hwclock to pass year 2038), rebooting on a kernel w/ this patch applied
and verifying the device was still 100 years in the future.
Signed-off-by: Arnaud Ebalard <arno@natisbad.org>
Suggested-by: Uwe Kleine-König <uwe@kleine-koenig.org>
Acked-by: Uwe Kleine-König <uwe@kleine-koenig.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: Peter Huewe <peter.huewe@infineon.com>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Thierry Reding <treding@nvidia.com>
Cc: Mark Brown <broonie@kernel.org>
Cc: Grant Likely <grant.likely@linaro.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
When Intersil ISL12057 support was added by commit 70e123373c ("rtc: Add
support for Intersil ISL12057 I2C RTC chip"), two masks for time registers
values imported from the device were either wrong or omitted, leading to
additional bits from those registers to impact read values:
- mask for hour register value when reading it in AM/PM mode. As
AM/PM mode is not the usual mode used by the driver, this error
would only have an impact on an externally configured RTC hour
later read by the driver.
- mask for month value. The lack of masking would provide an
erroneous value if century bit is set.
This patch fixes those two masks.
Fixes: 70e123373c ("rtc: Add support for Intersil ISL12057 I2C RTC chip")
Signed-off-by: Arnaud Ebalard <arno@natisbad.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: Peter Huewe <peter.huewe@infineon.com>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Thierry Reding <treding@nvidia.com>
Cc: Mark Brown <broonie@kernel.org>
Cc: Grant Likely <grant.likely@linaro.org>
Acked-by: Uwe Kleine-König <uwe@kleine-koenig.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
MCP7940x is same RTC as MCP7941x. The difference is that MCP7941x chips
contain additional EEPROM on a different i2c address.
DS1307 driver already supports MCP7941x, so just add a new i2c device id
and rename functions and defines accordingly.
Signed-off-by: Tomas Novotny <tomas@novotny.cz>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: Grant Likely <grant.likely@linaro.org>
Cc: Rob Herring <robh+dt@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add support for the watchdog functionality of the DS1374 rtc. Based on
the m41t80 watchdog functionality Note: watchdog uses the same registers
as alarm.
[akpm@linux-foundation.org: don't forget mutex_unlock() in ds1374_wdt_open() error path]
[akpm@linux-foundation.org: coding-style fixes]
Signed-off-by: Soeren Andersen <san@rosetechnology.dk>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Barry Song <Baohua.Song@csr.com>
Cc: hao liu <hao.liu@csr.com>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
In case the card is woken up of the rtc alarm, the
devm_rtc_device_register function detects it as a pending alarm about a
month in the future. Fix this by clearing the alarm in module probe.
Signed-off-by: Jan Kardell <jan.kardell@telliq.com>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: Grant Likely <grant.likely@linaro.org>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Vincent Donnefort <vdonnefort@gmail.com>
Cc: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
According to Haoyu hym8563 datasheet this saves som power. Might be
importat to battery life. And maybe it works for the NXP part as well.
Signed-off-by: Jan Kardell <jan.kardell@telliq.com>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: Grant Likely <grant.likely@linaro.org>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Vincent Donnefort <vdonnefort@gmail.com>
Cc: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
To guarantee that a set alarm occurs in the future, the set alarm time
is rounded up to the nearest minute. Also we cannot handle UIE as it
requires second precision.
Signed-off-by: Jan Kardell <jan.kardell@telliq.com>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: Grant Likely <grant.likely@linaro.org>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Vincent Donnefort <vdonnefort@gmail.com>
Cc: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Incorrect mask was used for hour and monthday fields.
Signed-off-by: Jan Kardell <jan.kardell@telliq.com>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: Grant Likely <grant.likely@linaro.org>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Vincent Donnefort <vdonnefort@gmail.com>
Cc: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The NXP datasheet says:
"Bits labeled as N should always be written with logic 0."
At least one of those bits is sometime read as a 1, therfore violating
this rule. To fix this we mask away those bits.
Signed-off-by: Jan Kardell <jan.kardell@telliq.com>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: Grant Likely <grant.likely@linaro.org>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Vincent Donnefort <vdonnefort@gmail.com>
Cc: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Remove some code that was left from before block read/write was used.
Signed-off-by: Jan Kardell <jan.kardell@telliq.com>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: Grant Likely <grant.likely@linaro.org>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Vincent Donnefort <vdonnefort@gmail.com>
Cc: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fix minor coding style issues like comment style, indentation and remove
a few unnecessary casts.
Also drop the 1 from OMAP1 in the driver description.
Signed-off-by: Johan Hovold <johan@kernel.org>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: Tony Lindgren <tony@atomide.com>
Cc: Benot Cousson <bcousson@baylibre.com>
Cc: Lokesh Vutla <lokeshvutla@ti.com>
Cc: Guenter Roeck <linux@roeck-us.net>
Cc: Sekhar Nori <nsekhar@ti.com>
Cc: Tero Kristo <t-kristo@ti.com>
Cc: Keerthy J <j-keerthy@ti.com>
Tested-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The ALARM interrupt must not be disabled during shutdown in order to be
able to power up the system using an RTC alarm.
Signed-off-by: Johan Hovold <johan@kernel.org>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: Tony Lindgren <tony@atomide.com>
Cc: Benot Cousson <bcousson@baylibre.com>
Cc: Lokesh Vutla <lokeshvutla@ti.com>
Cc: Guenter Roeck <linux@roeck-us.net>
Cc: Sekhar Nori <nsekhar@ti.com>
Cc: Tero Kristo <t-kristo@ti.com>
Cc: Keerthy J <j-keerthy@ti.com>
Tested-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add new property "ti,system-power-controller" to register the RTC as a
power-off handler.
Some RTC IP revisions can control an external PMIC via the pmic_power_en
pin, which can be configured to transition to OFF on ALARM2 events and
back to ON on subsequent ALARM (wakealarm) events.
This is based on earlier work by Colin Foe-Parker and AnilKumar Ch. [1]
[1] https://www.mail-archive.com/linux-omap@vger.kernel.org/msg82127.html
[akpm@linux-foundation.org: add comment]
Signed-off-by: Johan Hovold <johan@kernel.org>
Cc: Colin Foe-Parker <colin.foeparker@logicpd.com>
Cc: AnilKumar Ch <anilkumar@ti.com>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: Tony Lindgren <tony@atomide.com>
Cc: Benot Cousson <bcousson@baylibre.com>
Cc: Lokesh Vutla <lokeshvutla@ti.com>
Cc: Guenter Roeck <linux@roeck-us.net>
Cc: Sekhar Nori <nsekhar@ti.com>
Cc: Tero Kristo <t-kristo@ti.com>
Cc: Keerthy J <j-keerthy@ti.com>
Tested-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add helper to read raw BCD time that can be used in interrupt context.
Signed-off-by: Johan Hovold <johan@kernel.org>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: Tony Lindgren <tony@atomide.com>
Cc: Benot Cousson <bcousson@baylibre.com>
Cc: Lokesh Vutla <lokeshvutla@ti.com>
Cc: Guenter Roeck <linux@roeck-us.net>
Cc: Sekhar Nori <nsekhar@ti.com>
Cc: Tero Kristo <t-kristo@ti.com>
Cc: Keerthy J <j-keerthy@ti.com>
Tested-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Some legacy RTC IP revisions has a power-up reset flag in the status
register that later revisions lack.
As this flag is always read back as set on later revisions (or is
overloaded with a different flag), make sure to only clear the flag and
print the info message on legacy platforms.
Signed-off-by: Johan Hovold <johan@kernel.org>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: Tony Lindgren <tony@atomide.com>
Cc: Benot Cousson <bcousson@baylibre.com>
Cc: Lokesh Vutla <lokeshvutla@ti.com>
Cc: Guenter Roeck <linux@roeck-us.net>
Cc: Sekhar Nori <nsekhar@ti.com>
Cc: Tero Kristo <t-kristo@ti.com>
Cc: Keerthy J <j-keerthy@ti.com>
Tested-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Remove DRIVER_NAME macro which was used for unrelated strings (e.g.
id-table entry and module name), but not for related ones (e.g. module
name and alias).
Also move the module alias to the other module-info entries.
Signed-off-by: Johan Hovold <johan@kernel.org>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: Tony Lindgren <tony@atomide.com>
Cc: Benot Cousson <bcousson@baylibre.com>
Cc: Lokesh Vutla <lokeshvutla@ti.com>
Cc: Guenter Roeck <linux@roeck-us.net>
Cc: Sekhar Nori <nsekhar@ti.com>
Cc: Tero Kristo <t-kristo@ti.com>
Tested-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add struct omap_rtc to hold previously global data as well as the
IP-block feature flags.
Also convert the register-access macros to proper inline helper functions.
Signed-off-by: Johan Hovold <johan@kernel.org>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: Tony Lindgren <tony@atomide.com>
Cc: Benot Cousson <bcousson@baylibre.com>
Cc: Lokesh Vutla <lokeshvutla@ti.com>
Cc: Guenter Roeck <linux@roeck-us.net>
Cc: Sekhar Nori <nsekhar@ti.com>
Cc: Tero Kristo <t-kristo@ti.com>
Cc: Keerthy J <j-keerthy@ti.com>
Tested-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Make sure not to register the class device until after the device has
been configured.
Currently, the device is not fully configured (e.g. 24-hour mode) when
the class device is registered, something which involves driver
callbacks for example to read the current time.
Signed-off-by: Johan Hovold <johan@kernel.org>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: Tony Lindgren <tony@atomide.com>
Cc: Benot Cousson <bcousson@baylibre.com>
Cc: Lokesh Vutla <lokeshvutla@ti.com>
Cc: Guenter Roeck <linux@roeck-us.net>
Cc: Sekhar Nori <nsekhar@ti.com>
Cc: Tero Kristo <t-kristo@ti.com>
Cc: Keerthy J <j-keerthy@ti.com>
Tested-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Remove some debug messages and return errors from subsystems rather than
always fail with -EIO.
Note that the class-registration error has already been logged by rtc
core.
Signed-off-by: Johan Hovold <johan@kernel.org>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: Tony Lindgren <tony@atomide.com>
Cc: Benot Cousson <bcousson@baylibre.com>
Cc: Lokesh Vutla <lokeshvutla@ti.com>
Cc: Guenter Roeck <linux@roeck-us.net>
Cc: Sekhar Nori <nsekhar@ti.com>
Cc: Tero Kristo <t-kristo@ti.com>
Cc: Keerthy J <j-keerthy@ti.com>
Tested-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Use writel instead of writeb when disabling interrupts at probe as
ALARM2 is not cleared otherwise on some IP-block revisions (e.g.
AM3352).
Note that the driver currently never enables the ALARM2 interrupt.
Signed-off-by: Johan Hovold <johan@kernel.org>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: Tony Lindgren <tony@atomide.com>
Cc: Benot Cousson <bcousson@baylibre.com>
Cc: Lokesh Vutla <lokeshvutla@ti.com>
Cc: Guenter Roeck <linux@roeck-us.net>
Cc: Sekhar Nori <nsekhar@ti.com>
Cc: Tero Kristo <t-kristo@ti.com>
Cc: Keerthy J <j-keerthy@ti.com>
Tested-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The platform device must be registered as wakeup capable before
registering the class device, or the wakealarm attribute will not be
created.
Also make sure to unregister the wakeup source on probe errors.
Fixes: 1d2e2b65d0 ("rtc: omap: restore back (hard-code) wakeup support")
Signed-off-by: Johan Hovold <johan@kernel.org>
Reviewed-by: Felipe Balbi <balbi@ti.com>
Tested-by: Felipe Balbi <balbi@ti.com>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: Tony Lindgren <tony@atomide.com>
Cc: Benot Cousson <bcousson@baylibre.com>
Cc: Lokesh Vutla <lokeshvutla@ti.com>
Cc: Guenter Roeck <linux@roeck-us.net>
Cc: Sekhar Nori <nsekhar@ti.com>
Cc: Tero Kristo <t-kristo@ti.com>
Cc: Keerthy J <j-keerthy@ti.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This series fixes a few issues with the omap rtc-driver, cleans up a
bit, adds device abstraction, and finally adds support for the PMIC
control feature found in some revisions of this RTC IP block.
Ultimately, this allows for powering off the Beaglebone and waking it up
again on RTC alarms.
This patch (of 20):
Make sure not to reset the clock-source configuration when enabling the
32kHz clock mux.
Until the clock source can be configured through device tree we must not
overwrite settings made by the bootloader (e.g. clock-source
selection).
Fixes: cd914bba03 ("drivers/rtc/rtc-omap.c: add support for enabling 32khz clock")
Signed-off-by: Johan Hovold <johan@kernel.org>
Reviewed-by: Felipe Balbi <balbi@ti.com>
Tested-by: Felipe Balbi <balbi@ti.com>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: Tony Lindgren <tony@atomide.com>
Cc: Benot Cousson <bcousson@baylibre.com>
Cc: Lokesh Vutla <lokeshvutla@ti.com>
Cc: Guenter Roeck <linux@roeck-us.net>
Cc: Sekhar Nori <nsekhar@ti.com>
Cc: Tero Kristo <t-kristo@ti.com>
Cc: Keerthy J <j-keerthy@ti.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Some rtc devices always return '0' when rtc_class_ops.read_time is
called. So if rtc_time isn't verified in callback, rtc interface cannot
know whether rtc_time is valid.
Check rtc_time by using 'rtc_valid_tm' in '__rtc_read_time'. And add
the message for debugging.
Signed-off-by: Hyogi Gim <hyogi.gim@lge.com>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: John Stultz <john.stultz@linaro.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Move rtc register to be later than hardware initialization. The reason
is that devm_rtc_device_register() will do read_time() which is a
callback accessing hardware. This sometimes causes a hang in the
hardware related callback.
Signed-off-by: Guo Zeng <guo.zeng@csr.com>
Signed-off-by: Barry Song <Baohua.Song@csr.com>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Pull timer core updates from Thomas Gleixner:
"The time(r) departement provides:
- more infrastructure work on the year 2038 issue
- a few fixes in the Armada SoC timers
- the usual pile of fixlets and improvements"
* 'timers-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
clocksource: armada-370-xp: Use the reference clock on A375 SoC
watchdog: orion: Use the reference clock on Armada 375 SoC
clocksource: armada-370-xp: Add missing clock enable
time: Fix sign bug in NTP mult overflow warning
time: Remove timekeeping_inject_sleeptime()
rtc: Update suspend/resume timing to use 64bit time
rtc/lib: Provide y2038 safe rtc_tm_to_time()/rtc_time_to_tm() replacement
time: Fixup comments to reflect usage of timespec64
time: Expose get_monotonic_coarse64() for in-kernel uses
time: Expose getrawmonotonic64 for in-kernel uses
time: Provide y2038 safe mktime() replacement
time: Provide y2038 safe timekeeping_inject_sleeptime() replacement
time: Provide y2038 safe do_settimeofday() replacement
time: Complete NTP adjustment threshold judging conditions
time: Avoid possible NTP adjustment mult overflow.
time: Rename udelay_test.c to test_udelay.c
clocksource: sirf: Remove hard-coded clock rate
The at91 cleanups changed a lot of files, this merges in the
latest cleanups to resolve the conflicts
Conflicts:
arch/arm/mach-at91/at91sam9260.c
arch/arm/mach-at91/at91sam9261.c
arch/arm/mach-at91/at91sam9263.c
arch/arm/mach-at91/clock.c
arch/arm/mach-at91/clock.h
drivers/rtc/Kconfig
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
The precise selection is useless, so we simply remove these dependencies.
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: Boris BREZILLON <boris.brezillon@free-electrons.com>
Currently the rtc suspend/resume timing is done using
y2038 problematic timespecs. So update the code to utilize
timespec64 types.
Signed-off-by: John Stultz <john.stultz@linaro.org>
As part of addressing "y2038 problem" for in-kernel uses, this patch
adds safe rtc_tm_to_time64()/rtc_time64_to_tm() respectively using
time64_t.
After this patch, rtc_tm_to_time() is deprecated and all its call
sites will be fixed using corresponding safe versions, it can be
removed when having no users. Also change rtc_tm_to_time64() to
return time64_t directly instead of just as a parameter like
rtc_tm_to_time() does.
After this patch, rtc_time_to_tm() is deprecated and all its call
sites will be fixed using corresponding safe versions, it can be
removed when having no users.
In addition, change rtc_tm_to_ktime() and rtc_ktime_to_tm() to use
the safe version in passing.
Signed-off-by: pang.xunlei <pang.xunlei@linaro.org>
Signed-off-by: John Stultz <john.stultz@linaro.org>
This resolves some of the obvious conflicts between the at91 cleanup and
drivers branches.
Conflicts:
arch/arm/mach-at91/at91sam9g45.c
arch/arm/mach-at91/at91sam9rl.c
drivers/rtc/Kconfig
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
It is only about a not so recent driver for old platforms: RTT as RTC driver:
- RTT as RTC driver enhancements and machine specific include files removal
- RTT as RTC driver conversion to device tree
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)
iQEcBAABAgAGBQJUZg/EAAoJEAf03oE53VmQ/KAIAJi5Ky2ekaZ4FGWbDrnQBHV+
X0M/wvCdHw4D7VENo1W3U3ulf5r0XimeY6nnbmx3Ki0fTE2O3VyfLNzkjQtMf6iX
TfoJM9y4fWsY5AXnynYO1Gj/2CH6Xab79Kb5sxL8b9VvlUMxlsKoQOmUYHC775OX
YiBfp3dZYODkMyIIQmSkoZGj+kkgWbjMrp9CPueqVltha/EbfBP96Kib2G/aJVkb
F9QyOq8B/mpUk2P29L1hc9X0/tjwaLZsO97zzhYVj7VwZS9sbYztQgmUNdtEds4/
7EhMwSXxb9L5LkuoyuHFpRLMGzLrN9XBftE58s92hXwnM2KZE4eNo/JF0SGDOKo=
=POJG
-----END PGP SIGNATURE-----
Merge tag 'at91-drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/nferre/linux-at91 into next/drivers
Pull "First batch of drivers for 3.19" from Nicolas Ferre:
It is only about a not so recent driver for old platforms: RTT as RTC driver:
- RTT as RTC driver enhancements and machine specific include files removal
- RTT as RTC driver conversion to device tree
* tag 'at91-drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/nferre/linux-at91:
rtc: at91sam9: add DT bindings documentation
rtc: at91sam9: use clk API instead of relying on AT91_SLOW_CLOCK
ARM: at91: add clk_lookup entry for RTT devices
rtc: at91sam9: rework the Kconfig description
rtc: at91sam9: make use of syscon/regmap to access GPBR registers
rtc: at91sam9: add DT support
rtc: at91sam9: replace devm_ioremap by devm_ioremap_resource
rtc: at91sam9: use standard readl/writel functions instead of raw versions
rtc: at91sam9: remove references to mach specific headers
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
When removing old board !DT support, several Kconfig options were deleted.
Propagate this removal to drivers Kconfig files.
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
The patch implements the OPAL rtc driver that binds with the rtc
driver subsystem. The driver uses the platform device infrastructure
to probe the rtc device and register it to rtc class framework. The
'wakeup' is supported depending upon the property 'has-tpo' present
in the OF node. It provides a way to load the generic rtc driver in
in the absence of an OPAL driver.
The patch also moves the existing OPAL rtc get/set time interfaces to the
new driver and exposes the necessary OPAL calls using EXPORT_SYMBOL_GPL.
Test results:
-------------
Host:
[root@tul169p1 ~]# ls -l /sys/class/rtc/
total 0
lrwxrwxrwx 1 root root 0 Oct 14 03:07 rtc0 -> ../../devices/opal-rtc/rtc/rtc0
[root@tul169p1 ~]# cat /sys/devices/opal-rtc/rtc/rtc0/time
08:10:07
[root@tul169p1 ~]# echo `date '+%s' -d '+ 2 minutes'` > /sys/class/rtc/rtc0/wakealarm
[root@tul169p1 ~]# cat /sys/class/rtc/rtc0/wakealarm
1413274345
[root@tul169p1 ~]#
FSP:
$ smgr mfgState
standby
$ rtim timeofday
System time is valid: 2014/10/14 08:12:04.225115
$ smgr mfgState
ipling
$
CC: devicetree@vger.kernel.org
CC: tglx@linutronix.de
CC: rtc-linux@googlegroups.com
CC: a.zummo@towertech.it
Signed-off-by: Neelesh Gupta <neelegup@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
The RTT block is using the slow clock which is accessible through the clk
API.
Use the clk API to retrieve, enable and get the slow clk rate instead of
the AT91_SLOW_CLOCK macro (which hardcodes the slow clk rate).
Doing this allows us to reference the clk thus preventing the CCF from
disabling it during the "disable unused" phase.
Signed-off-by: Boris BREZILLON <boris.brezillon@free-electrons.com>
Acked-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Acked-by: Johan Hovold <johan@kernel.org>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Remove all references to AT91CAP9 SoC which has been removed.
Rework help message to remove any specific references to AT91SAM9 SoCs.
State that RTC_DRV_AT91SAM9_RTT and RTC_DRV_AT91SAM9_GPBR options are only
used when booting non DT boards.
Signed-off-by: Boris BREZILLON <boris.brezillon@free-electrons.com>
Acked-by: Johan Hovold <johan@kernel.org>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
The GPBR registers are not part of the RTT block and thus should not be
defined in the reg property of the rtt node.
Use syscon to provide a proper DT representation and reference the GPBR
syscon device in a new "atmel,rtt-rtc-time-reg" property which store both
the syscon device phandle and the register offset within the GPBR block.
When using non DT boards, we won't be able to retrieve the syscon regmap,
hence we need to create our own regmap using the memory region defined
in the 2nd memory resource assigned to the RTT platform device.
Signed-off-by: Boris BREZILLON <boris.brezillon@free-electrons.com>
Acked-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Acked-by: Johan Hovold <johan@kernel.org>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Add of_match_table to the existing driver so that rtt nodes defined in at91
DTs can be attached to this driver.
Signed-off-by: Boris BREZILLON <boris.brezillon@free-electrons.com>
Acked-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Acked-by: Johan Hovold <johan@kernel.org>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Replace devm_ioremap calls by devm_ioremap_resource which already check
resource consistency (resource != NULL) and print an error in case of
failure.
Signed-off-by: Boris BREZILLON <boris.brezillon@free-electrons.com>
Acked-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Acked-by: Johan Hovold <johan@kernel.org>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Raw versions of writel and writel should not be directly used and should
be replaced by their relaxed versions (readl/writel_relaxed), which take
endianness conversion into account.
In this driver we prefer the standard readl/writel function which add the
appropriate memory barrier around the access (the performance penalty is
negligible for this kind of application).
Signed-off-by: Boris BREZILLON <boris.brezillon@free-electrons.com>
Acked-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Acked-by: Johan Hovold <johan@kernel.org>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
In order to support multi platform kernel drivers should not include
machine specific headers.
Copy RTT macros in the driver code and remove any machine specific
headers.
Signed-off-by: Boris BREZILLON <boris.brezillon@free-electrons.com>
Acked-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Acked-by: Johan Hovold <johan@kernel.org>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
As there is currently no-one to take care of this old !MMU target and as its
support in recent kernels is a bit rotten, remove this at91x40 support and the
board file associated with it (at91eb01).
There are modern ARM !MMU in Mainline now so this target is not interesting for
building tests anymore. It would be better to start from these modern ARM !MMU
platforms to reintroduce at91x40 support if needed.
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Greg Ungerer <gerg@uclinux.org>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Fix register value in bq32000 trickle charging.
Mike reported that I'm using wrong value in one trickle-charging case,
and after checking docs, I must admit he's right.
Signed-off-by: Pavel Machek <pavel@denx.de>
Reported-by: Mike Bremford <mike@bfo.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fix unconditional initialization failure on non-exynos3250 SoCs.
Commit df9e26d093 ("rtc: s3c: add support for RTC of Exynos3250 SoC")
introduced rtc source clock support, but also added initialization
failure on SoCs, which doesn't need such clock.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Adds support for RTC device inside PM8941 PMIC. The RTC in this PMIC
have two register spaces. Thus the rtc-pm8xxx is slightly reworked to
reflect these differences.
The register set for different PMIC chips are selected on DT compatible
string base.
[akpm@linux-foundation.org: coding-style fixes]
[akpm@linux-foundation.org: simplify and fix locking in pm8xxx_rtc_set_time()]
Signed-off-by: Stanimir Varbanov <svarbanov@mm-sol.com>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: Stephen Boyd <sboyd@codeaurora.org>
Cc: Josh Cartwright <joshc@codeaurora.org>
Cc: Stanimir Varbanov <svarbanov@mm-sol.com>
Cc: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Pull x86 EFI updates from Peter Anvin:
"This patchset falls under the "maintainers that grovel" clause in the
v3.18-rc1 announcement. We had intended to push it late in the merge
window since we got it into the -tip tree relatively late.
Many of these are relatively simple things, but there are a couple of
key bits, especially Ard's and Matt's patches"
* 'x86-efi-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (24 commits)
rtc: Disable EFI rtc for x86
efi: rtc-efi: Export platform:rtc-efi as module alias
efi: Delete the in_nmi() conditional runtime locking
efi: Provide a non-blocking SetVariable() operation
x86/efi: Adding efi_printks on memory allocationa and pci.reads
x86/efi: Mark initialization code as such
x86/efi: Update comment regarding required phys mapped EFI services
x86/efi: Unexport add_efi_memmap variable
x86/efi: Remove unused efi_call* macros
efi: Resolve some shadow warnings
arm64: efi: Format EFI memory type & attrs with efi_md_typeattr_format()
ia64: efi: Format EFI memory type & attrs with efi_md_typeattr_format()
x86: efi: Format EFI memory type & attrs with efi_md_typeattr_format()
efi: Introduce efi_md_typeattr_format()
efi: Add macro for EFI_MEMORY_UCE memory attribute
x86/efi: Clear EFI_RUNTIME_SERVICES if failing to enter virtual mode
arm64/efi: Do not enter virtual mode if booting with efi=noruntime or noefi
arm64/efi: uefi_init error handling fix
efi: Add kernel param efi=noruntime
lib: Add a generic cmdline parse function parse_option_str
...
Commit b5ada4600d ("drivers/rtc/rtc-cmos.c: fix compilation warning
when !CONFIG_PM_SLEEP") broke wakeup from S5 by making cmos_poweroff a
nop unless CONFIG_PM_SLEEP was defined.
Fix this by restricting the #ifdef to cmos_resume and restoring the old
dependency on CONFIG_PM for cmos_suspend and cmos_poweroff.
Signed-off-by: Daniel Glöckner <daniel-gl@gmx.net>
Cc: Mika Westerberg <mika.westerberg@linux.intel.com>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Instead of pushing each byte let's reduce stack usage by using %*ph specifier.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
As pointed out by Sergei Shtylyov, the pcf8563_irq function contains a
bug in the error handling: an interrupt handler is not supposed to
return an errno value but an 'enum irqreturn'.
Let's fix this by returning IRQ_NONE in case of a communication error.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Cc: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
gcc-4.9 found a potential condition under which the 'pending' variable
may be used uninitialized:
drivers/rtc/rtc-pcf8563.c: In function 'pcf8563_irq':
drivers/rtc/rtc-pcf8563.c:173:5: warning: 'pending' may be used uninitialized in this function [-Wmaybe-uninitialized]
This is because in the pcf8563_get_alarm_mode() function, we check any
nonzero return of pcf8563_read_block_data, but in the irq function we
only check for negative values, so a possible positive value does not
get detected if the compiler chooses not to inline the entire call
chain.
Checking for any non-zero value in the interrupt handler as well is just
as correct and lets the compiler know what we are doing, without needing
a bogus initialization.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Cc: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Linus Torvalds