All these clock controllers are little endian devices, but so far
we've been relying on the regmap mmio bus handling this for us
without explicitly stating that fact. After commit 4a98da2164cf
(regmap-mmio: Use native endianness for read/write, 2015-10-29),
the regmap mmio bus will read/write with the __raw_*() IO
accessors, instead of using the readl/writel() APIs that do
proper byte swapping for little endian devices.
So if we're running on a big endian processor and haven't
specified the endianness explicitly in the regmap config or in
DT, we're going to switch from doing little endian byte swapping
to big endian accesses without byte swapping, leading to some
confusing results. On my apq8074 dragonboard, this causes the
device to fail to boot as we access the clock controller with
big endian IO accesses even though the device is little endian.
Specify the endianness explicitly so that the regmap core
properly byte swaps the accesses for us.
Reported-by: Kevin Hilman <khilman@linaro.org>
Tested-by: Tyler Baker <tyler.baker@linaro.org>
Tested-by: Kevin Hilman <khilman@linaro.org>
Cc: Simon Arlott <simon@fire.lp0.eu>
Cc: Mark Brown <broonie@kernel.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Put these clocks into the dt files instead of registering them
from C code. This provides a few benefits. It allows us to
specify the frequency of these clocks at the board level instead
of hard-coding them in the driver. It allows us to insert an RPM
clock in between the consumers of the crystals and the actual
clock. And finally, it helps us transition the GCC driver to use
RPM clocks when that configuration is enabled.
Cc: Georgi Djakov <georgi.djakov@linaro.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Now that qcom_cc_remove() is a nop, drop calls to
qcom_cc_remove() and any empty driver remove functions.
Cc: Rajendra Nayak <rnayak@codeaurora.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
There's just one GDSC as part of the msm8974 GCC block.
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Rajendra Nayak <rnayak@codeaurora.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
The other ce clocks have the flag set, but ce1 doesn't, so
clk_set_rate() doesn't propagate up the tree to the ce1_src_clk.
Set the flag as this is supported.
Reported-by: Bjorn Andersson <bjorn.andersson@sonymobile.com>
Tested-by: Bjorn Andersson <bjorn.andersson@sonymobile.com>
Fixes: 0282465320 ("clk: qcom: Add APQ8084 Global Clock Controller support")
Fixes: d33faa9ead ("clk: qcom: Add support for MSM8974's global clock controller (GCC)")
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Make const both the array and the strings, so they can be
moved to .rodata section.
Signed-off-by: Georgi Djakov <georgi.djakov@linaro.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
In the current parent mapping code, we can get duplicate or inconsistent
indexes, which leads to discrepancy between the number of elements in the
array and the number of parents. Until now, this was solved with some
reordering but this is not always possible.
This patch introduces index tables that are used to define the relations
between the PLL source and the hardware mux configuration value.
To accomplish this, here we do the following:
- Define a parent_map struct to map the relations between PLL source index
and register configuration value.
- Add a qcom_find_src_index() function for finding the index of a clock
matching the specific PLL configuration.
- Update the {set,get}_parent RCG functions use the newly introduced
parent_map struct.
- Convert all existing drivers to the new parent_map tables.
Signed-off-by: Georgi Djakov <georgi.djakov@linaro.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
A new PLL (gpll4) is added on msm8974 PRO devices to support a
faster sdc1 clock rate. Add support for this and the two new sdcc
cal clocks.
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
The address of the blsp2_ahb_clk register is incorrect. Fix it.
Signed-off-by: Georgi Djakov <gdjakov@mm-sol.com>
Reviewed-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
Most of the probe code is the same between all the different
clock controllers. Consolidate the code into a common.c file.
This makes changes to the common probe parts easier and reduces
chances for bugs.
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
Add a driver for the global clock controller found on MSM 8974
based platforms. This should allow most non-multimedia device
drivers to probe and control their clocks.
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
Stephen Boyd