Commit 2abb0d5268 ("PM / devfreq: Lock devfreq in trans_stat_show")
revealed a missing locking while calling devfreq_update_status() function
during suspend/resume cycle.
Code analysis revealed that devfreq_set_target() function was called
without needed locks held for setting device specific suspend_freq if such
has been defined. This patch fixes that by adding the needed locking, what
fixes following kernel warning on Exynos4412-based OdroidU3 board during
system suspend:
PM: suspend entry (deep)
Filesystems sync: 0.002 seconds
Freezing user space processes ... (elapsed 0.001 seconds) done.
OOM killer disabled.
Freezing remaining freezable tasks ... (elapsed 0.001 seconds) done.
------------[ cut here ]------------
WARNING: CPU: 2 PID: 1385 at drivers/devfreq/devfreq.c:204 devfreq_update_status+0xc0/0x188
Modules linked in:
CPU: 2 PID: 1385 Comm: rtcwake Not tainted 5.4.0-rc6-next-20191111 #6848
Hardware name: SAMSUNG EXYNOS (Flattened Device Tree)
[<c0112588>] (unwind_backtrace) from [<c010e070>] (show_stack+0x10/0x14)
[<c010e070>] (show_stack) from [<c0afb010>] (dump_stack+0xb4/0xe0)
[<c0afb010>] (dump_stack) from [<c01272e0>] (__warn+0xf4/0x10c)
[<c01272e0>] (__warn) from [<c01273a8>] (warn_slowpath_fmt+0xb0/0xb8)
[<c01273a8>] (warn_slowpath_fmt) from [<c07d105c>] (devfreq_update_status+0xc0/0x188)
[<c07d105c>] (devfreq_update_status) from [<c07d2d70>] (devfreq_set_target+0xb0/0x15c)
[<c07d2d70>] (devfreq_set_target) from [<c07d3598>] (devfreq_suspend+0x2c/0x64)
[<c07d3598>] (devfreq_suspend) from [<c05de0b0>] (dpm_suspend+0xa4/0x57c)
[<c05de0b0>] (dpm_suspend) from [<c05def74>] (dpm_suspend_start+0x98/0xa0)
[<c05def74>] (dpm_suspend_start) from [<c0195b58>] (suspend_devices_and_enter+0xec/0xc74)
[<c0195b58>] (suspend_devices_and_enter) from [<c0196a20>] (pm_suspend+0x340/0x410)
[<c0196a20>] (pm_suspend) from [<c019480c>] (state_store+0x6c/0xc8)
[<c019480c>] (state_store) from [<c033fc50>] (kernfs_fop_write+0x10c/0x228)
[<c033fc50>] (kernfs_fop_write) from [<c02a6d3c>] (__vfs_write+0x30/0x1d0)
[<c02a6d3c>] (__vfs_write) from [<c02a9afc>] (vfs_write+0xa4/0x180)
[<c02a9afc>] (vfs_write) from [<c02a9d58>] (ksys_write+0x60/0xd8)
[<c02a9d58>] (ksys_write) from [<c0101000>] (ret_fast_syscall+0x0/0x28)
Exception stack(0xed3d7fa8 to 0xed3d7ff0)
...
irq event stamp: 9667
hardirqs last enabled at (9679): [<c0b1e7c4>] _raw_spin_unlock_irq+0x20/0x58
hardirqs last disabled at (9698): [<c0b16a20>] __schedule+0xd8/0x818
softirqs last enabled at (9694): [<c01026fc>] __do_softirq+0x4fc/0x5fc
softirqs last disabled at (9719): [<c012fe68>] irq_exit+0x16c/0x170
---[ end trace 41ac5b57d046bdbc ]---
------------[ cut here ]------------
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Acked-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Currently interrupt-driven governors (like NVIDIA Tegra30 ACTMON governor)
are used to set polling_ms=0 in order to avoid periodic polling of device
status by devfreq core. This means that polling interval can't be changed
by userspace for such governors.
The new governor flag allows interrupt-driven governors to convey that
devfreq core shouldn't perform polling of device status and thus generic
devfreq polling interval could be supported by these governors now.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Reviewed-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
There is no locking in this sysfs show function so stats printing can
race with a devfreq_update_status called as part of freq switching or
with initialization.
Also add an assert in devfreq_update_status to make it clear that lock
must be held by caller.
Fixes: 39688ce6fa ("PM / devfreq: account suspend/resume for stats")
Cc: stable@vger.kernel.org
Signed-off-by: Leonard Crestez <leonard.crestez@nxp.com>
Reviewed-by: Matthias Kaehlcke <mka@chromium.org>
Reviewed-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
The governor is initialized after sysfs attributes become visible so in
theory the governor field can be NULL here.
Fixes: bcf23c79c4 ("PM / devfreq: Fix available_governor sysfs")
Signed-off-by: Leonard Crestez <leonard.crestez@nxp.com>
Reviewed-by: Matthias Kaehlcke <mka@chromium.org>
Reviewed-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Before creating a new devfreq device devfreq_add_device() checks
if there is already a devfreq dev associated with the requesting
device (parent). If that's the case the function rejects to create
another devfreq dev for that parent and logs an error. The error
message is very unspecific, make it a bit more explicit.
Reviewed-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Matthias Kaehlcke <mka@chromium.org>
Signed-off-by: MyungJoo Ham <myungjoo.ham@samsung.com>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Correct the documentation for devm_devfreq_remove_device() argument.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Reviewed-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: MyungJoo Ham <myungjoo.ham@samsung.com>
A bit unexpectedly (but still documented), request_module may
return a positive value, in case of a modprobe error.
This is currently causing issues in the devfreq framework.
When a request_module exits with a positive value, we currently
return that via ERR_PTR. However, because the value is positive,
it's not a ERR_VALUE proper, and is therefore treated as a
valid struct devfreq_governor pointer, leading to a kernel oops.
Fix this by returning -EINVAL if request_module returns a positive
value.
Fixes: b53b012805 ("PM / devfreq: Fix static checker warning in try_then_request_governor")
Signed-off-by: Ezequiel Garcia <ezequiel@collabora.com>
Reviewed-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: MyungJoo Ham <myungjoo.ham@samsung.com>
Based on 2 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license version 2 as
published by the free software foundation
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license version 2 as
published by the free software foundation #
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference in 4122 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Enrico Weigelt <info@metux.net>
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Allison Randal <allison@lohutok.net>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190604081206.933168790@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch add basic tracing of the devfreq workqueue and delayed work.
It aims to capture changes of the polling intervals and device state.
Signed-off-by: Lukasz Luba <l.luba@partner.samsung.com>
Reviewed-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: MyungJoo Ham <myungjoo.ham@samsung.com>
The patch 23c7b54ca1cd: "PM / devfreq: Fix devfreq_add_device() when
drivers are built as modules." leads to the following static checker
warning:
drivers/devfreq/devfreq.c:1043 governor_store()
warn: 'governor' can also be NULL
The reason is that the try_then_request_governor() function returns both
error pointers and NULL. It should just return error pointers, so fix
this by returning a ERR_PTR to the error intead of returning NULL.
Fixes: 23c7b54ca1 ("PM / devfreq: Fix devfreq_add_device() when drivers are built as modules.")
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Reviewed-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: MyungJoo Ham <myungjoo.ham@samsung.com>
If the new governor fails to start, switch back to old governor so that the
devfreq state is not left in some weird limbo.
[Myungjoo: assume fatal on revert failure and set df->governor to NULL]
Signed-off-by: Sibi Sankar <sibis@codeaurora.org>
Signed-off-by: Saravana Kannan <skannan@codeaurora.org>
Reviewed-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: MyungJoo Ham <myungjoo.ham@samsung.com>
Following up with complaints on inconsistent indentation from
Yangtao Li, this fixes indentation inconsistency.
In principle, this tries to put arguments aligned to the left
including the first argument except for the case where
the first argument is on the far-right side.
Signed-off-by: MyungJoo Ham <myungjoo.ham@samsung.com>
Reviewed-by: Chanwoo Choi <cw00.choi@samsung.com>
Acked-by: Yangtao Li <tiny.windzz@gmail.com>
devm_kzalloc() could fail, so insert a check of its return value. And
if it fails, returns -ENOMEM.
Signed-off-by: Yangtao Li <tiny.windzz@gmail.com>
Signed-off-by: MyungJoo Ham <myungjoo.ham@samsung.com>
'devfreq' is malloced in devfreq_add_device() and should be freed in
the error handling cases, otherwise it will cause memory leak.
Signed-off-by: Yangtao Li <tiny.windzz@gmail.com>
Signed-off-by: MyungJoo Ham <myungjoo.ham@samsung.com>
This patch adds implementation for global suspend/resume for
devfreq framework. System suspend will next use these functions.
Suggested-by: Tobias Jakobi <tjakobi@math.uni-bielefeld.de>
Suggested-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Lukasz Luba <l.luba@partner.samsung.com>
Reviewed-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: MyungJoo Ham <myungjoo.ham@samsung.com>
The patch prepares devfreq device for handling suspend/resume
functionality. The new fields will store needed information during this
process. Devfreq framework handles opp-suspend DT entry and there is no
need of modyfications in the drivers code. It uses atomic variables to
make sure no race condition affects the process.
Suggested-by: Tobias Jakobi <tjakobi@math.uni-bielefeld.de>
Suggested-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Lukasz Luba <l.luba@partner.samsung.com>
Reviewed-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: MyungJoo Ham <myungjoo.ham@samsung.com>
The refactoring is needed for the new client in devfreq: suspend.
To avoid code duplication, move it to the new local function
devfreq_set_target.
Suggested-by: Tobias Jakobi <tjakobi@math.uni-bielefeld.de>
Suggested-by: Chanwoo Choi <cw00.choi@samsung.com>
Reviewed-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Lukasz Luba <l.luba@partner.samsung.com>
Signed-off-by: MyungJoo Ham <myungjoo.ham@samsung.com>
kfree has taken the null pointer into account. hence it is safe
to remove the redundant null pointer check before kfree.
Signed-off-by: zhong jiang <zhongjiang@huawei.com>
Signed-off-by: MyungJoo Ham <myungjoo.ham@samsung.com>
device_release() is freeing the resources before calling the device
specific release callback which is, in the case of devfreq, stopping
the governor.
It is a problem as some governors are using the device resources. e.g.
simpleondemand which is using the devfreq deferrable monitoring work. If it
is not stopped before the resources are freed, it might lead to a use after
free.
Signed-off-by: Vincent Donnefort <vincent.donnefort@arm.com>
Reviewed-by: John Einar Reitan <john.reitan@arm.com>
[cw00.choi: Fix merge conflict]
Reviewed-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: MyungJoo Ham <myungjoo.ham@samsung.com>
Commit ab8f58ad72 ("PM / devfreq: Set min/max_freq when adding the
devfreq device") initializes df->min/max_freq with the min/max OPP when
the device is added. Later commit f1d981eaec ("PM / devfreq: Use the
available min/max frequency") adds df->scaling_min/max_freq and the
following to the frequency adjustment code:
max_freq = MIN(devfreq->scaling_max_freq, devfreq->max_freq);
With the current handling of min/max_freq this is incorrect:
Even though df->max_freq is now initialized to a value != 0 user space
can still set it to 0, in this case max_freq would be 0 instead of
df->scaling_max_freq as intended. In consequence the frequency adjustment
is not performed:
if (max_freq && freq > max_freq) {
freq = max_freq;
To fix this set df->min/max freq to the min/max OPP in max/max_freq_store,
when the user passes a value of 0. This also prevents df->max_freq from
being set below the min OPP when df->min_freq is 0, and similar for
min_freq. Since it is now guaranteed that df->min/max_freq can't be 0 the
checks for this case can be removed.
Fixes: f1d981eaec ("PM / devfreq: Use the available min/max frequency")
Signed-off-by: Matthias Kaehlcke <mka@chromium.org>
Reviewed-by: Brian Norris <briannorris@chromium.org>
Reviewed-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: MyungJoo Ham <myungjoo.ham@samsung.com>
Drop the custom MIN/MAX macros in favour of the standard min/max from
kernel.h
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Reviewed-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: MyungJoo Ham <myungjoo.ham@samsung.com>
When the devfreq driver and the governor driver are built as modules,
the call to devfreq_add_device() or governor_store() fails because the
governor driver is not loaded at the time the devfreq driver loads. The
devfreq driver has a build dependency on the governor but also should
have a runtime dependency. We need to make sure that the governor driver
is loaded before the devfreq driver.
This patch fixes this bug by adding a try_then_request_governor()
function. First tries to find the governor, and then, if it is not found,
it requests the module and tries again.
Fixes: 1b5c1be2c8 (PM / devfreq: map devfreq drivers to governor using name)
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Reviewed-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: MyungJoo Ham <myungjoo.ham@samsung.com>
Commit ab8f58ad72 ("PM / devfreq: Set min/max_freq when adding
the devfreq device") introduced the initialization of the user
limits min/max_freq from the lowest/highest available OPPs. Later
commit f1d981eaec ("PM / devfreq: Use the available min/max
frequency") added scaling_min/max_freq, which actually represent
the frequencies of the lowest/highest available OPP. scaling_min/
max_freq are initialized with the values from min/max_freq, which
is totally correct in the context, but a bit awkward to read.
Swap the initialization and assign scaling_min/max_freq with the
OPP freqs and then the user limts min/max_freq with scaling_min/
max_freq.
Needless to say that this change is a NOP, intended to improve
readability.
Signed-off-by: Matthias Kaehlcke <mka@chromium.org>
Reviewed-by: Chanwoo Choi <cw00.choi@samsung.com>
Reviewed-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: MyungJoo Ham <myungjoo.ham@samsung.com>
Never directly free @dev after calling device_register() or
device_unregister(), even if device_register() returned an error.
Always use put_device() to give up the reference initialized.
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Reviewed-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: MyungJoo Ham <myungjoo.ham@samsung.com>
df->governor is being dereferenced before it is null checked,
hence there is a potential null pointer dereference.
Notice that df->governor is being null checked at line 1004:
if (df->governor) {, which implies it might be null.
Fix this by null checking df->governor before dereferencing it.
Addresses-Coverity-ID: 1401988 ("Dereference before null check")
Fixes: bcf23c79c4 ("PM / devfreq: Fix available_governor sysfs")
Signed-off-by: Gustavo A. R. Silva <garsilva@embeddedor.com>
Reviewed-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: MyungJoo Ham <myungjoo.ham@samsung.com>
Propagate the error of devfreq_add_device() in devm_devfreq_add_device()
rather than statically returning ENOMEM. This makes it slightly faster
to pinpoint the cause of a returned error.
Fixes: 8cd84092d3 ("PM / devfreq: Add resource-managed function for devfreq device")
Cc: stable@vger.kernel.org
Acked-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: MyungJoo Ham <myungjoo.ham@samsung.com>
The freq_table array of each devfreq device is always not NULL.
In result, it is unneeded to check whether profile->freq_table
is NULL or not.
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: MyungJoo Ham <myungjoo.ham@samsung.com>
The commit a76caf55e5 ("thermal: Add devfreq cooling") allows
the devfreq device to use the cooling device. When the cooling down
are required, the devfreq_cooling.c disables the OPP entry with
the dev_pm_opp_disable(). In result, 'available_frequencies'[1]
sysfs node never came to show the all available frequencies.
[1] /sys/class/devfreq/.../available_frequencies
So, this patch uses the 'freq_table' in the 'struct devfreq_dev_profile'
in order to show the all available frequencies.
- If 'freq_table' is NULL, devfreq core initializes them by using OPP values.
- If 'freq_table' is initialized, devfreq core just uses the 'freq_table'.
And this patch adds some comment about the sort way of 'freq_table'.
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: MyungJoo Ham <myungjoo.ham@samsung.com>
This patch changes the return type of devfreq_set_freq_table()
from 'void' to 'int' in order to check whether it fails or not.
And This patch just removes the 'devfreq' prefix and the description
of function. Because the helper functions are only used by the devfreq.
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: MyungJoo Ham <myungjoo.ham@samsung.com>
The commit a76caf55e5 ("thermal: Add devfreq cooling") is able
to disable OPP as a cooling device. In result, both update_devfreq()
and {min|max}_freq_show() have to consider the 'opp->available'
status of each OPP.
So, this patch adds the 'scaling_{min|max}_freq' to struct devfreq
in order to indicate the available mininum and maximum frequency
by adjusting OPP interface such as dev_pm_opp_{disable|enable}().
The 'scaling_{min|max}_freq' are used for on both update_devfreq()
and {min|max}_freq_show().
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: MyungJoo Ham <myungjoo.ham@samsung.com>
This reverts commit 3104fa3081.
The {min|max}_freq_show() show the stored value of the struct devfreq.
But, if the drivers/thermal/devfreq_cooling.c disables the specific
frequency value, {min|max}_freq_show() have to check this situation
before showing the stored value. So, this patch revert the macro
in order to add the additional codes.
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: MyungJoo Ham <myungjoo.ham@samsung.com>
Prior to that, the min/max_freq of the devfreq device are always zero
before the user changes the min/max_freq through sysfs entries.
It might make the confusion for the min/max_freq.
This patch initializes the available min/max_freq by using the OPP
during adding the devfreq device.
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: MyungJoo Ham <myungjoo.ham@samsung.com>
When the devfreq_add_device fails to register deivce, the memory
leak of devfreq instance happen. So, this patch fix the memory
leak issue. Before freeing the devfreq instance checks whether
devfreq instance is NULL or not because the device_unregister()
frees the devfreq instance when jumping to the 'err_init'.
It is to prevent the duplicate the kfee(devfreq).
Cc: stable@vger.kernel.org
Fixes: ac4b281176 ("PM / devfreq: fix duplicated kfree on devfreq pointer")
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: MyungJoo Ham <myungjoo.ham@samsung.com>
Fix typos and add the following to the scripts/spelling.txt:
followings||following
While we are here, add a missing colon in the boilerplate in DT binding
documents. The "you SoC" in allwinner,sunxi-pinctrl.txt was fixed as
well.
I reworded "as the followings:" to "as follows:" for
drivers/usb/gadget/udc/renesas_usb3.c.
Link: http://lkml.kernel.org/r/1481573103-11329-32-git-send-email-yamada.masahiro@socionext.com
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* pm-devfreq:
PM / devfreq: Modify the device name as devfreq(X) for sysfs
PM / devfreq: Simplify the sysfs name of devfreq-event device
PM / devfreq: Remove unnecessary separate _remove_devfreq()
PM / devfreq: Fix wrong trans_stat of passive devfreq device
PM / devfreq: Fix available_governor sysfs
PM / devfreq: exynos-ppmu: Show the registred device for ppmu device
PM / devfreq: Fix the wrong description for userspace governor
PM / devfreq: Fix the checkpatch warnings
PM / devfreq: exynos-bus: Print the real clock rate of bus
PM / devfreq: exynos-ppmu: Use the regmap interface to handle the registers
PM / devfreq: exynos-bus: Add the detailed correlation for Exynos5433
PM / devfreq: Don't delete sysfs group twice
This patch modifies the device name as devfreq(X) for sysfs by using the 'devfreq'
prefix word instead of separate device name. On user-space aspect, user would
find the some devfreq drvier with 'devfreq(X)' pattern. So, this patch modify the
device name as following:
- /sys/class/devfreq/[non-standard device name] -> /sys/class/devfreq/devfreq(X)
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: MyungJoo Ham <myungjoo.ham@samsung.com>
The _remove_devfreq() releases the all resources of the devfreq
device. This function is only called in the devfreq_dev_release().
For that reason, the devfreq core doesn't need to leave the
_remove_devfreq() separately. This patch releases the all
resources in the devfreq_dev_release() and then removes the
_remove_devfreq().
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: MyungJoo Ham <myungjoo.ham@samsung.com>
Until now, the trans_stat information of passive devfreq is not updated.
This patch updates the trans_stat information after setting the target
frequency of passive devfreq device.
Fixes: 996133119f ("PM / devfreq: Add new passive governor")
Cc: stable@vger.kernel.org
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: MyungJoo Ham <myungjoo.ham@samsung.com>
The devfreq using passive governor is not able to change the governor.
So, the user can not change the governor through 'available_governor' sysfs
entry. Also, the devfreq which don't use the passive governor is not able to
change to 'passive' governor on the fly.
Fixes: 996133119f ("PM / devfreq: Add new passive governor")
Cc: stable@vger.kernel.org
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: MyungJoo Ham <myungjoo.ham@samsung.com>
This patch just fixes the checkpatch warnings.
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: MyungJoo Ham <myungjoo.ham@samsung.com>
This patch updates dev_pm_opp_find_freq_*() routines to get a reference
to the OPPs returned by them.
Also updates the users of dev_pm_opp_find_freq_*() routines to call
dev_pm_opp_put() after they are done using the OPPs.
As it is guaranteed the that OPPs wouldn't get freed while being used,
the RCU read side locking present with the users isn't required anymore.
Drop it as well.
This patch also updates all users of devfreq_recommended_opp() which was
returning an OPP received from the OPP core.
Note that some of the OPP core routines have gained
rcu_read_{lock|unlock}() calls, as those still use RCU specific APIs
within them.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Reviewed-by: Chanwoo Choi <cw00.choi@samsung.com> [Devfreq]
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Let the OPP core provide helpers to register notifiers for any device,
instead of exposing srcu_head outside of the core.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Acked-by: MyungJoo Ham <myungjoo.ham@samsung.com>
Reviewed-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
This patch fixes the bug of devfreq_add_device(). The devfreq device must
have the default governor. If find_devfreq_governor() returns error,
devfreq_add_device() fail to add the devfreq instance.
Fixes: 1b5c1be2c8 (PM / devfreq: map devfreq drivers to governor using name)
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The function name in the comment was incorrect.
Signed-off-by: MyungJoo Ham <myungjoo.ham@samsung.com>
Reviewed-by: Chanwoo Choi <cw00.choi@samsung.com>
In case devfreq->previous_freq is still uninitialized in
devfreq_update_status(), i.e. it has value '0', the lookups in
that function fail, eventually leading to some error message:
[ 3.041292] devfreq bus_dmc: Couldn't update frequency transition information.
Just skip the statup update in this situation.
Signed-off-by: Tobias Jakobi <tjakobi@math.uni-bielefeld.de>
Acked-by: MyungJoo Ham <myungjoo.ham@samsung.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Use devfreq_list_lock around list_del() to prevent list corruption.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Acked-by: MyungJoo Ham <myungjoo.ham@samsung.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
of_node_put needs to be called when the device node which is got
from of_parse_phandle has finished using.
Cc: MyungJoo Ham <myungjoo.ham@samsung.com>
Cc: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Peter Chen <peter.chen@nxp.com>
Signed-off-by: MyungJoo Ham <myungjoo.ham@samsung.com>
The Kconfig currently controlling compilation of this code is:
menuconfig PM_DEVFREQ
bool "Generic Dynamic Voltage and Frequency Scaling (DVFS) support"
...meaning that it currently is not being built as a module by anyone.
Lets remove the modular code that is essentially orphaned, so that
when reading the driver there is no doubt it is builtin-only.
This code wasn't using module_init, so we don't need to be concerned
with altering the initcall level here.
We also delete the MODULE_LICENSE tag etc. since all that information
is already contained at the top of the file in the comments.
We don't replace module.h with init.h since the file already has that.
But we do add export.h since this file does export some symbols.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Reviewed-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: MyungJoo Ham <myungjoo.ham@samsung.com>
Marek Szyprowski