Tidy the tuning loop by moving it to a separate function and making it a
for-loop.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
There are only 2 possible block sizes, so simplify 2 if-statements into 1.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Factor out some functions to tidy up the code in sdhci_execute_tuning.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Use mmc_abort_tuning() instead of open-coding the stop command.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
If a tuning command times out, the card could still be processing it, which
will cause problems for recovery. The eMMC specification says that CMD12
can be used to stop CMD21, so add a function that does that.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
SDHCI falls back to fixed sampling if there is an error during tuning.
However it also reports an error unless there is periodic re-tuning.
That is not the best option because:
a) there is a reasonable chance that fixed sampling will work, especially
at room temperature.
b) re-tuning will be done again anyway if there are CRC errors.
Change to return no error always when falling back to fixed sampling.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
If the driver has exhausted the maximum number of tuning loops, then fixed
sampling is used. To do that both SDHCI_CTRL_TUNED_CLK and
SDHCI_CTRL_EXEC_TUNING must be reset to 0, but only SDHCI_CTRL_TUNED_CLK
was being reset. Reset SDHCI_CTRL_EXEC_TUNING to 0 also.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Clearing the tuning bits should reset the tuning circuit. However there is
more to do. Reset the command and data lines for good measure, and then
for eMMC ensure the card is not still trying to process a tuning command by
sending a stop command.
Note the JEDEC eMMC specification says the stop command (CMD12) can be used
to stop a tuning command (CMD21) whereas the SD specification is silent on
the subject with respect to the SD tuning command (CMD19). Considering that
CMD12 is not a valid SDIO command, the stop command is sent only when the
tuning command is CMD21 i.e. for eMMC. That addresses cases seen so far
which have been on eMMC.
Note that this replaces the commit fe5fb2e3b5 ("mmc: sdhci: Reset cmd and
data circuits after tuning failure") which is being reverted for v4.9+.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Tested-by: Dan O'Donovan <dan@emutex.com>
Cc: stable@vger.kernel.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This reverts commit fe5fb2e3b5 ("mmc: sdhci: Reset cmd and data circuits
after tuning failure").
A better fix is available, and it will be applied to older stable releases,
so get this out of the way by reverting it.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Cc: stable@vger.kernel.org # v4.9+
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The JEDEC specification indicates CMD13 can be used after a HS200 switch
to check for errors. However in practice some boards experience CRC errors
in the CMD13 response. Consequently, for HS200, CRC errors are not a
reliable way to know the switch failed. If there really is a problem, we
would expect tuning will fail and the result ends up the same. So change
the error condition to ignore CRC errors in that case.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Acked-by: Jaehoon Chung <jh80.chung@samsung.com>
Reviewed-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Add an entry for the SDIO bus in the ECS EF20 cherry trail laptop:
Device (SDHB) {
Name (_ADR, 0x00110000)
Name (_HID, "80860F14" /* Intel Baytrail SDIO/MMC Host Controller */)
Name (_CID, "PNP0D40" /* SDA Standard Compliant SD Host Controller */)
Name (_DDN, "Intel(R) SDIO Controller - 80862295")
Name (_UID, 0x02)
Name (_HRV, One)
A SDHB device with the same _HID and _UID can also be found on other
cherry trail products like Chuwi Hi10.
Signed-off-by: Daniel Drake <drake@endlessm.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
I see no override of read/write callbacks in sdhci-of-at91.c.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
On NI 9037 boards the max SDIO frequency is limited by trace lengths
and other layout choices. The max SDIO frequency is stored in an ACPI
table.
The driver reads the ACPI entry MXFQ during sdio_probe_slot and sets the
f_max field of the host.
Signed-off-by: Nathan Sullivan <nathan.sullivan@ni.com>
Reviewed-by: Jaeden Amero <jaeden.amero@ni.com>
Reviewed-by: Josh Cartwright <joshc@ni.com>
Signed-off-by: Zach Brown <zach.brown@ni.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Add PCI ID for Intel byt sdio host controller sub-vended by NI.
The controller has different behavior because of the board layout NI
puts it on.
Signed-off-by: Zach Brown <zach.brown@ni.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Before calling clk_round_rate(), put the spin_unlock_irq() in
sdhci_s3c_consider_clock() function.
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
When card is polling (broken-cd), there is a spamming messge related to
clock.
After applied this patch, display the message only one time at boot
time. It's enough to check which clock values is used.
Also prevent to display the spamming message.
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
If card is polling or non-removable, display the more exact message.
It's helpful to debug which detecting scheme is using.
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Before checking flags, it has to check "present" variable.
Otherwise, flags should be cleared everytime.
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The commit 64997de4fd17 ("mmc: dw_mmc: remove system PM callback") is
missing to call dw_mci_ctrl_reset(). This adds to call
dw_mci_ctrl_reset() and to handle error of clocks.
Signed-off-by: Joonyoung Shim <jy0922.shim@samsung.com>
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The dw_mmc-exynos should be RPM_ACTIVE on probe() to call suspend
callback of runtime PM in pm_runtime_force_suspend() during first system
suspend. Also call pm_runtime_get_noresume() on probe() because it
doesn't call suspend/resume callback by runtime PM now.
Signed-off-by: Joonyoung Shim <jy0922.shim@samsung.com>
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
It is unnecessary to panic the kernel when testing mmc. Instead,
cast a warning for folkz to debug and return the error code to
the caller to indicate the failure of this test should be enough.
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
bounce_sg for mqrq_cur and mqrq_pre are proper
allocated when initializing the queue and will not
be freed before explicitly cleaning the queue. So from
the code itself it should be quite confident to remove
this check. If that BUG_ON take effects, it is mostly
likely the memory is randomly oopsing.
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The code seems quite simple to maintain the sdio_uart_table,
and the insert/remove port from the table are symmetric. If
the BUG_ON occurs, which means serial_core modify the index
or mess up the port sequence anyway.
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
BUG_ONs doesn't help anything except for stop the system from
running. If it occurs, it implies we should deploy proper error
handling for that. So this patch is gonna discard these meaningless
BUG_ONs and deploy error handling if needed.
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
BUG_ONs doesn't help anything except for stop the system from
running. If it occurs, it implies we should deploy proper error
handling for that. So this patch is gonna discard these meaningless
BUG_ONs and deploy error handling if needed.
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
BUG_ONs doesn't help anything except for stop the system from
running. If it occurs, it implies we should deploy proper error
handling for that. So this patch is gonna discard these meaningless
BUG_ONs and deploy error handling if needed.
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Return error value for file_operations callback instead
of triggering BUG_ON which is meaningless. Personally I
don't believe n != EXT_CSD_STR_LEN could happen. Anyway,
propagate the error to the caller.
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
BUG_ONs doesn't help anything except for stop the system from
running. If it occurs, it implies we should deploy proper error
handling for that. So this patch is gonna discard these meaningless
BUG_ONs and deploy error handling if needed.
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Add a mmc_queue member to record the size of the queue, which currently
supports 2 requests on-the-go at a time. Instead of allocating resources
for 2 slots in the queue, allow for an arbitrary number.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
In preparation for supporting a queue of requests, factor out
mmc_queue_reqs_free_bufs().
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Harjani Ritesh <riteshh@codeaurora.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
In preparation for supporting a queue of requests, factor out
mmc_queue_alloc_sgs().
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Harjani Ritesh <riteshh@codeaurora.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The only time the driver sleeps expecting to be woken upon the arrival of
a new request, is when the dispatch queue is empty. The only time that it
is known whether the dispatch queue is empty is after NULL is returned
from blk_fetch_request() while under the queue lock.
Recognizing those facts, simplify the synchronization between the queue
thread and the request function. A couple of flags tell the request
function what to do, and the queue lock and barriers associated with
wake-ups ensure synchronization.
The result is simpler and allows the removal of the context_info lock.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Harjani Ritesh <riteshh@codeaurora.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The 4K native sector check does not allow for the 'do' loop nor the
variables used after the 'cmd_abort' label.
'brq' and 'req' get reassigned in the 'do' loop, so the check must not
assume what their values are. After the 'cmd_abort' label, 'mq_rq' and
'req' are used, but 'rqc' must be NULL otherwise it can be started again.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The eSDHC of T4240-R1.0-R2.0 has incorrect vender version and spec version.
Acturally the right version numbers should be VVN=0x13 and SVN = 0x1.
This patch adds the GUTS driver support for eSDHC driver to match SoC.
And fix host version to avoid that incorrect version numbers break down
the ADMA data transfer.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Acked-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Scott Wood <oss@buserror.net>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
I've had it with this code now.
The packed command support is a complex hurdle in the MMC/SD block
layer, around 500+ lines of code which was introduced in 2013 in
commit ce39f9d17c ("mmc: support packed write command for eMMC4.5
devices")
commit abd9ac1449 ("mmc: add packed command feature of eMMC4.5")
...and since then it has been rotting. The original author of the
code has disappeared from the community and the mail address is
bouncing.
For the code to be exercised the host must flag that it supports
packed commands, so in mmc_blk_prep_packed_list() which is called for
every single request, the following construction appears:
u8 max_packed_rw = 0;
if ((rq_data_dir(cur) == WRITE) &&
mmc_host_packed_wr(card->host))
max_packed_rw = card->ext_csd.max_packed_writes;
if (max_packed_rw == 0)
goto no_packed;
This has the following logical deductions:
- Only WRITE commands can really be packed, so the solution is
only half-done: we support packed WRITE but not packed READ.
The packed command support has not been finalized by supporting
reads in three years!
- mmc_host_packed_wr() is just a static inline that checks
host->caps2 & MMC_CAP2_PACKED_WR. The problem with this is
that NO upstream host sets this capability flag! No driver
in the kernel is using it, and we can't test it. Packed
command may be supported in out-of-tree code, but I doubt
it. I doubt that the code is even working anymore due to
other refactorings in the MMC block layer, who would
notice if patches affecting it broke packed commands?
No one.
- There is no Device Tree binding or code to mark a host as
supporting packed read or write commands, just this flag
in caps2, so for sure there are not any DT systems using
it either.
It has other problems as well: mmc_blk_prep_packed_list() is
speculatively picking requests out of the request queue with
blk_fetch_request() making the MMC/SD stack harder to convert
to the multiqueue block layer. By this we get rid of an
obstacle.
The way I see it this is just cruft littering the MMC/SD
stack.
Cc: Namjae Jeon <namjae.jeon@samsung.com>
Cc: Maya Erez <qca_merez@qca.qualcomm.com>
Acked-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The void (*pre_req) callback in the struct mmc_host_ops vtable
is passing an argument "is_first_req" indicating whether this is
the first request or not.
None of the in-kernel users use this parameter: instead, since
they all just do variants of dma_map* they use the DMA cookie
to indicate whether a pre* callback has already been done for
a request when they decide how to handle it.
Delete the parameter from the callback and all users, as it is
just pointless cruft.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
According to the JEDEC specification, during bus timing change operations
for mmc, sending a CMD13 could trigger CRC errors.
As switching to HS DDR mode indeed causes a bus timing change, polling with
CMD13 to detect card busy, may thus potentially trigger CRC errors.
Currently these errors are treated as the switch to HS DDR mode failed.
To improve this behaviour, let's instead tell __mmc_switch() to retry when
it encounters CRC errors during polling.
Moreover, when switching to HS DDR mode, let's make sure the CMD13 polling
is done by having the mmc host and the mmc card, being configured to
operate at the same selected bus speed timing. Fix this by providing
MMC_TIMING_MMC_DDR52 as the timing parameter to __mmc_switch().
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Tested-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
In cases when the mmc host doesn't support HW busy detection, polling for a
card being busy by using CMD13 is beneficial. That is because, instead of
waiting a fixed amount of time, 500ms or the generic CMD6 time from
EXT_CSD, we find out a lot sooner when the card stops signaling busy. This
leads to a significant decreased total initialization time for the mmc
card.
However, to allow polling with CMD13 during a bus timing change operation,
such as switching to HS mode, we first need to update the mmc host's bus
timing before starting to poll. Deal with that, simply by providing
MMC_TIMING_MMC_HS as the timing parameter to __mmc_switch() from
mmc_select_hs().
By telling __mmc_switch() to allow polling with CMD13, also makes it
validate the CMD6 status, thus we can remove the corresponding checks.
When switching to HS400ES, the mmc_select_hs() function is called in one of
the intermediate steps. To still prevent CMD13 polling for HS400ES, let's
call the __mmc_switch() function in this path as it enables us to keep
using the existing method.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Tested-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
In cases when a speed mode change is requested for mmc cards, a CMD6 is
sent by calling __mmc_switch() during the card initialization. The CMD6
leads to the card entering a busy period. When that is completed, the host
must parse the CMD6 status to find out whether the change of the speed mode
succeeded.
To enable the mmc core to poll the card by using CMD13 to find out when the
busy period is completed, it's reasonable to make sure polling is done by
having the mmc host and the mmc card, being configured to operate at the
same selected bus speed timing.
Therefore, let's extend __mmc_switch() to take yet another parameter, which
allow its callers to update the bus speed timing of the mmc host. In this
way, __mmc_switch() also becomes capable of reading and validating the CMD6
status by sending a CMD13, in cases when that's desired.
If __mmc_switch() encounters a failure, we make sure to restores the old
bus speed timing for the mmc host, before propagating the error code.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Tested-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
According to the JEDEC specification, the SWITCH_ERROR bit in the device
status from a R1 response, is an error bit which may be cleared as soon as
the response that reports the error is sent.
When polling with CMD13 to find out when the card stops signaling busy
after a CMD6 has been sent, we currently parse only the last CMD13 response
for the SWITCH_ERROR bit. Consequentially we could loose important
information about the card.
In worst case if the card stops signaling busy within the allowed timeout,
we could end up believing that the CMD6 command completed successfully,
when in fact it didn't.
To improve the behaviour, let's parse each CMD13 response to see if the
SWITCH_ERROR bit is set in the device status. In such case, we abort the
polling loop and report the error.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Tested-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
The ignore_crc parameter/variable name is used at a couple of places in the
mmc core. Let's rename it to retry_crc_err to reflect its new purpose.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Tested-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
There are only one users left which calls __mmc_send_status(). Moreover,
the ignore_crc parameter isn't being used, so let's just remove these
redundant parts.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Tested-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
After a CMD6 command has been sent, the __mmc_switch() function might be
advised to poll the card for busy by using CMD13 and also by ignoring CRC
errors.
In the case of ignoring CRC errors, the mmc core tells the mmc host to also
ignore these errors via masking the MMC_RSP_CRC response flag. This seems
wrong, as it leads to that the mmc host could propagate an unreliable
response, instead of a proper error code.
What we really want, is not to ignore CRC errors but instead retry the
polling attempt. So, let's change this by treating a CRC error as the card
is still being busy and thus continue to run the polling loop.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Tested-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
With commit f35bbf61ab ("gpio / ACPI: Return -EPROBE_DEFER if the
gpiochip was not found"), a gpio descriptor request can now be deferred if
the providing gpio host controller driver hasn't been loaded yet. Allow use
in mmc slot probe in order to prevent card detect gpio setup from failing
in this case.
Signed-off-by: David E. Box <david.e.box@linux.intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The newer msm sdhci's cores use a different DLL hardware for HS400.
Update the configuration and calibration of the newer DLL block.
The HS400 DLL block used previously is CDC LP 533 and requires
programming multiple registers and waiting for configuration to
complete and then enable it. It has about 18 register writes and
two register reads.
The newer HS400 DLL block is SDC4 DLL and requires two register
writes for configuration and one register read to confirm that it
is initialized. There is an additional register write to enable
the power save mode for SDC4 DLL block.
Signed-off-by: Ritesh Harjani <riteshh@codeaurora.org>
Signed-off-by: Krishna Konda <kkonda@codeaurora.org>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
In HS400 mode a new RCLK is introduced on the interface for read data
transfers. The eMMC5.0 device transmits the read data to the host with
respect to rising and falling edges of RCLK. In order to ensure correct
operation of read data transfers in HS400 mode, the incoming RX data
needs to be sampled by delayed version of RCLK.
The CDCLP533 delay circuit shifts the RCLK by T/4. It needs to be
initialized, configured and enabled once during HS400 mode switch and
when operational voltage/clock is changed.
Signed-off-by: Venkat Gopalakrishnan <venkatg@codeaurora.org>
Signed-off-by: Ritesh Harjani <riteshh@codeaurora.org>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Save the tuning phase once the tuning is performed.
This phase value will be used while calibrating DLL
for HS400 mode.
Signed-off-by: Ritesh Harjani <riteshh@codeaurora.org>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The following msm platform specific changes are added to support HS400.
- Allow tuning for HS400 mode.
- Configure HS400 timing mode using the VENDOR_SPECIFIC_FUNC register.
Signed-off-by: Venkat Gopalakrishnan <venkatg@codeaurora.org>
Signed-off-by: Ritesh Harjani <riteshh@codeaurora.org>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
SDHC MSM controller need 2x clock for MCLK at GCC.
Hence make required changes to have 2x clock for
DDR timing modes.
Signed-off-by: Ritesh Harjani <riteshh@codeaurora.org>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
sdhci-msm controller may have different clk-rates for each
bus speed mode. Thus implement set_clock callback for
sdhci-msm driver.
Signed-off-by: Sahitya Tummala <stummala@codeaurora.org>
Signed-off-by: Ritesh Harjani <riteshh@codeaurora.org>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Factor out sdhci_enable_clk from sdhci_set_clock
and make it EXPORT_SYMBOL so that it can be called.
Signed-off-by: Ritesh Harjani <riteshh@codeaurora.org>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This add get_min_clock() and get_max_clock() callback
for sdhci-msm. sdhci-msm min/max clocks may be different
hence implement these callbacks.
Signed-off-by: Sahitya Tummala <stummala@codeaurora.org>
Signed-off-by: Ritesh Harjani <riteshh@codeaurora.org>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
SDCC core with minor version >= 0x42 introduced new 14lpp
DLL. This has additional requirements in the reset sequence
for DLL tuning. Make necessary changes as needed.
Without this patch we see below errors on such SDHC controllers
sdhci_msm 7464900.sdhci: mmc0: DLL failed to LOCK
mmc0: tuning execution failed: -110
Signed-off-by: Venkat Gopalakrishnan <venkatg@codeaurora.org>
Signed-off-by: Ritesh Harjani <riteshh@codeaurora.org>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This patch changes the poor style of writel/readl registers
into more readable format. This avoid mixed style format
of readl/writel in sdhci-msm driver.
This patch also removes the one line comments which were present for
above writel/readl, since they were of no help.
Signed-off-by: Ritesh Harjani <riteshh@codeaurora.org>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The "clock-freq-min-max" property was deprecated.
There is "max-frequency" property in drivers/mmc/core/host.c
"max-frequency" can be replaced with "clock-freq-min-max".
Minimum clock value might be set to 100K by default.
Then MMC core should try to find the correct value from 400K to 100K.
So it just needs to set Maximum clock value.
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Reviewed-by: Shawn Lin <shawn.lin@rock-chips.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
stop_cmdr should be set to values relevant to stop command.
It migth be assigned to values whatever there is mrq->stop or not.
Then it doesn't need to use dw_mci_prepare_command().
It's enough to use the prep_stop_abort for preparing stop command.
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Tested-by: Heiko Stuebner <heiko@sntech.de>
Reviewed-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
If DW_MMC_CARD_NO_USE_HOLD isn't set, it's usesd by default.
Enve if SDMMC_CMD_USB_HOLD_REG is set in prepare_command(), but it
doesn't set in pre_stop_abort().
To maintain the consistency, add the checking condition for this.
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Tested-by: Heiko Stuebner <heiko@sntech.de>
Reviewed-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
If there is no property "clock-freq-min-max", mmc->f_min should be set
to 400K by default. But Some SoC can be used 100K.
When 100K is used, MMC core will try to check from 400K to 100K.
Reported-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Tested-by: Heiko Stuebner <heiko@sntech.de>
Reviewed-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
If display the debug message, this message should be spamming.
If flags is maintained the previous value, didn't display the debug
message.
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Tested-by: Heiko Stuebner <heiko@sntech.de>
Reviewed-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Developer wants to see the real register value, not register offset.
This patch fixed to display the real value of register.
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Tested-by: Heiko Stuebner <heiko@sntech.de>
Reviewed-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Trivial fix to spelling mistake "desciptor" to "descriptor" in
dev_dbg message.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
By moving the mmc_packed_init() and mmc_packed_clean() into the
only file in the kernel where they are used, we save two exported
functions and can staticize those to the block.c file.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The struct mmc_blk_request contains an opaque void *data that
is actually only used to store a pointer to a per-request
struct mmc_blk_data. This is confusing, so rename the member
to blkdata and forward-declare the block.c local struct.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Instead of open coding the check for the same thing that
the helper checks: use the helper.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Request card detect and write protect gpios using the provided API
by mmc core.
If a gpio is provided for card detect, we don't need to poll.
So only use polling when a gpio is not provided.
Once all pdata users register the gpios using gpio descriptors,
we could remove the platform callbacks.
Signed-off-by: Axel Haslam <ahaslam@baylibre.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Tested-by: David Lechner <david@lechnology.com>
Card detect and write protect are currently not working on a DT
boot, and the driver relies on polling to get the state
of the card. The current code depends on platform data callbacks
to register and get the state of the gpios.
mmc core provides a generic way to parse device tree configuration,
which will take care of registering the gpios for us, lets use it
so that we don't need to poll, and parse the same properties.
Signed-off-by: Axel Haslam <ahaslam@baylibre.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Tested-by: David Lechner <david@lechnology.com>
We surely have SDIO support by now :)
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Commit 7729c7a232 ("mmc: tmio: Provide separate interrupt handlers")
refactored the sdio irq handler and wrongly used the mask for SD irqs,
not for SDIO irqs. This doesn't really matter in practice because both
values keep the only interrupt we are interested in. But still, this is
wrong and wants to be fixed.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
wbsd_request_dma() does not check for dma mapping errors.
Found by Linux Driver Verification project (linuxtesting.org).
Signed-off-by: Alexey Khoroshilov <khoroshilov@ispras.ru>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
We never set "ret" to RESULT_OK.
Fixes: 9f9c4180f8 ("mmc: mmc_test: add test for non-blocking transfers")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The type of host->private is (unsigned long *). No cast is needed
to return an opaque pointer.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Add bytewise register accesses support for newer versions of IPROC
SDHCI controllers.
Previous sdhci-iproc versions of SDIO controllers
(such as Raspberry Pi and Cygnus) only allowed for 32-bit register
accesses.
Signed-off-by: Srinath Mannam <srinath.mannam@broadcom.com>
Signed-off-by: Scott Branden <scott.branden@broadcom.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Add tuning support for use with SDR104 mode
This includes adding support for the sampling clock controller (SCC).
Based on work by Ai Kyuse.
Cc: Ai Kyuse <ai.kyuse.uw@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Acked-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Tested-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Add tuning support for use with SDR104 mode
Signed-off-by: Ai Kyuse <ai.kyuse.uw@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Acked-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Tested-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
An illegal sequence command error may occur if there is a stopbit or
cmd_index error as well as a CRC error. The correct course of action
is to re-enable IRQs
An illegal sequence data error may occur if there is a CRC or stopbit
error, or underrun. In this case set data->error correctly.
This is in preparation for enabling tuning support which relies on
differentiating between illegal sequence and other errors.
Signed-off-by: Ai Kyuse <ai.kyuse.uw@renesas.com>
[simon: broken out of a larger patch]
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Acked-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Tested-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Add support for r7s72100 SoC.
Signed-off-by: Chris Brandt <chris.brandt@renesas.com>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
For the r7s72100 SOC, the DATA_PORT register was changed to 32-bits wide.
Therefore a new flag has been created that will allow 32-bit reads/writes
to the DATA_PORT register instead of 16-bit (because 16-bits accesses are
not supported).
Signed-off-by: Chris Brandt <chris.brandt@renesas.com>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
In moving platforms from board files to DT, there still needs to be a way
to set the ocr_mask setting for the tmio driver during probe. Without this
setting, the probe will fail because the supported voltages are not known.
This patch will also traditional platform registration platforms to
migrate to DT.
Signed-off-by: Chris Brandt <chris.brandt@renesas.com>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
There were several instances of code using the
enum mmc_blk_status by arbitrarily converting it to an int and
throwing it around to different functions. This makes the code
hard to understand to may give rise to strange errors.
Especially the function prototype mmc_start_req() had to be
modified to take a pointer to an enum mmc_blk_status and the
function pointer .err_check() inside struct mmc_async_req
needed to return an enum mmc_blk_status.
In every case: instead of assigning the block layer error code
to an int, use the enum, also change the signature of all
functions actually passing this enum to use the enum.
To make it possible to use the enum everywhere applicable, move
it to <linux/mmc/core.h> so that all code actually using it can
also see it.
An interesting case was encountered in the MMC test code which
did not return a enum mmc_blk_status at all in the .err_check
function supposed to check whether asynchronous requests worked
or not: instead it returned a normal -ERROR or even the test
frameworks internal error codes.
The test code would also pass on enum mmc_blk_status codes as
error codes inside the test code instead of converting them
to the local RESULT_* codes.
I have tried to fix all instances properly and run some tests
on the result.
Cc: Chunyan Zhang <zhang.chunyan@linaro.org>
Cc: Baolin Wang <baolin.wang@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The ecc_err flag is only assigned 0 or 1 and treated as a bool,
so convert it to a bool.
Cc: Chunyan Zhang <zhang.chunyan@linaro.org>
Cc: Baolin Wang <baolin.wang@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This gen_err flag is only assigned 0 or 1 and treated as a bool,
so convert it to a bool.
Cc: Chunyan Zhang <zhang.chunyan@linaro.org>
Cc: Baolin Wang <baolin.wang@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The sdhci capabilities register can be incorrect. The sdhci-caps-mask
and sdhci-caps dt properties specify which bits of the register are
incorrect and what their values should be. This patch makes the sdhci
driver use those properties to correct the caps during
__sdhci_read_caps.
During __sdhci_read_caps
Use the sdhci-caps-mask property to turn off the incorrect bits of the
sdhci register after reading them.
Use the sdhci-caps to turn on bits after using sdhci-caps-mask to turn
off the incorrect ones.
Signed-off-by: Zach Brown <zach.brown@ni.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The ST Micro-specific busy detection was made after the assumption
that only this variant supports busy detection. So when doing busy
detection, the host immediately tries to use some ST-specific
register bits.
Since the qualcomm variant also supports some busy detection
schemes, encapsulate the variant flags better in the variant struct
and prepare to add more variants by just providing some bitmasks
to the logic.
Put the entire busy detection logic within an if()-clause in the
mmci_cmd_irq() function so the code is only executed when busy
detection is enabled, and so that it is kept in (almost) one
place, and add comments describing what is going on so the
code can be understood.
Tested on the Ux500 by introducing some prints in the busy
detection path and noticing how the IRQ is enabled, used and
disabled successfully.
Cc: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
There was some confusion in the CPSM (Command Path State Machine)
and DPSM (Data Path State Machine) regarding the naming of the
registers, clarify the meaning of this acronym so the naming is
understandable, and consistently use BIT() to define these fields.
Consequently name the register bit defines MCI_[C|D]PSM_* and
adjust the driver as well.
Include new definitions for a few bits found in a patch from
Srinivas Kandagatla.
Cc: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Support for DMA slave map has been added to the s3c24xx-dma
controller in commit 34681d84a0
"dmaengine: s3c24xx: Add dma_slave_map for s3c2440 devices"
This patch converts the s3cmci driver to also use it, so we can
eventually get rid of the exported filter function once all
related DMA clients are updated.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The MMC_CAP2_NO_PRESCAN_POWERUP was invented to avoid running the power up
sequence, mmc_power_up(), during ->probe() of the mmc host driver, but
instead defer this to the mmc detect work. This is especially useful for
those hosts that suffers from a long initialization time, as this time
would otherwise add up to the total boot time.
However, due to the introduction of runtime PM of mmc host devices in the
mmc core, this behaviour changed a bit. More precisely, it caused the mmc
core to runtime resume the host device during ->probe() of the host driver.
In cases like the rtsx_usb_sdmmc, runtime resuming the device may be costly
and thus affecting the total boot time.
To improve this behaviour when using MMC_CAP2_NO_PRESCAN_POWERUP, let's
postpone also calling mmc_power_off() when starting the host. This change
allows the mmc core to avoid runtime resuming the device, as it don't need
to claim the host for that execution path.
Cc: Ritesh Raj Sarraf <rrs@researchut.com>
Cc: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Initial support for the SD/eMMC controller in the Amlogic S905/GX*
family of SoCs.
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Now there are no variant drivers using dw_mci_suspend
and dw_mci_resume, so let's remove it.
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Let's migrate it to use runtime PM and remove the system
PM callback from this driver. With this patch, it could
handle system PM properly and could also use runtime PM
if we enable it.
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Let's migrate it to use runtime PM and remove the system
PM callback from this driver. With this patch, it could
handle system PM properly and could also use runtime PM
if we enable it.
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Let's migrate it to use runtime PM and remove the system
PM callback from this driver. With this patch, it could
handle system PM properly and could also use runtime PM
if we enable it.
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Let's migrate it to use runtime PM and remove the system
PM callback from this driver. With this patch, it could
handle system PM properly and could also use runtime PM
if we enable it.
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
We could disable biu clk if gpio card detect available,
or it is a non-removable device.
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Add new helper API mmc_can_gpio_cd for slot-gpio to make
host drivers know whether it supports gpio card detect.
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This patch adds runtime PM support for dw_mmc-rockchip.
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This patch add dw_mci_runtime_suspend/resume interfaces
and expose it to dw_mci variant driver to support runtime
PM.
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
When polling for busy after sending a MMC_SWITCH command, both the optional
->card_busy() callback and CMD13 are being used in conjunction.
This doesn't make sense. Instead it's more reasonable to rely solely on the
->card_busy() callback when it exists. Let's change that and instead use
the CMD13 as a fall-back. In this way we avoid sending CMD13, unless it's
really needed.
Within this context, let's also take the opportunity to make some
additional clean-ups and clarifications to the related code.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Jaehoon Chung <jh80.chung@samsung.com>
Tested-by: Jaehoon Chung <jh80.chung@samsung.com>
In yet another step of cleaning up __mmc_switch(), let's factor out the
code that deals with card busy polling.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Jaehoon Chung <jh80.chung@samsung.com>
Tested-by: Jaehoon Chung <jh80.chung@samsung.com>
The __mmc_switch() deserves a clean-up. In this step, let's move some code
outside of the do-while loop, which deal deals with the card busy polling.
This change simplifies the code in that sense that it becomes easier to follow
what is being executed during card busy polling, but it also gives a better
understanding for when polling isn't done.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Jaehoon Chung <jh80.chung@samsung.com>
Tested-by: Jaehoon Chung <jh80.chung@samsung.com>
Following changes needs mmc_switch_status() to be available both from mmc.c
and mmc_ops.c. Allow that by moving its implementation to mmc_ops.c and
make it available via mmc_ops.h.
Moving mmc_switch_status() to mmc_ops.c, also enables us to turn
mmc_switch_status_error() into static function. So let's take the
opportunity to change this as well.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Jaehoon Chung <jh80.chung@samsung.com>
Tested-by: Jaehoon Chung <jh80.chung@samsung.com>
Provides runtime PM callbacks to enable and disable clock resources
when idle. Also support system PM callbacks to be called during system
suspend and resume.
Reviewed-by: Ritesh Harjani <riteshh@codeaurora.org>
Reviewed-by: Georgi Djakov <georgi.djakov@linaro.org>
Tested-by: Ritesh Harjani <riteshh@codeaurora.org>
Signed-off-by: Pramod Gurav <pramod.gurav@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
VMMC is an optional regulator, which means that mmc_regulator_get_supply
will only return an error in case of a deferred probe, but not when the
regulator is not set in the DT.
However, the sunxi driver assumes that VMMC is always there, and doesn't
check the value of the regulator pointer before using it, which obviously
leads to a (close to) null pointer dereference.
Add proper checks to prevent that.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
If the driver is built as a module, autoload won't work because the module
alias information is not filled. So user-space can't match the registered
device with the corresponding module.
Export the module alias information using the MODULE_DEVICE_TABLE() macro.
Before this patch:
$ modinfo drivers/mmc/host/sdhci-of-at91.ko | grep alias
$
After this patch:
$ modinfo drivers/mmc/host/sdhci-of-at91.ko | grep alias
alias: of:N*T*Catmel,sama5d2-sdhciC*
alias: of:N*T*Catmel,sama5d2-sdhci
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Acked-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
If the driver is built as a module, autoload won't work because the module
alias information is not filled. So user-space can't match the registered
device with the corresponding module.
Export the module alias information using the MODULE_DEVICE_TABLE() macro.
Before this patch:
$ modinfo drivers/mmc/host/mtk-sd.ko | grep alias
$
After this patch:
$ modinfo drivers/mmc/host/mtk-sd.ko | grep alias
alias: of:N*T*Cmediatek,mt8135-mmcC*
alias: of:N*T*Cmediatek,mt8135-mmc
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Enable runtime PM autosuspend for the rtsx_usb_sdmmc driver to avoid the
device being runtime suspended and runtime resumed between each request.
Let's use a default timeout of 50ms, to be consistent with other mmc hosts.
Cc: Ritesh Raj Sarraf <rrs@researchut.com>
Cc: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
value of ios->timing is not related with SDCHI v3.0. If Controller version
is v3.0, SDHCI_QUIRK_NO_HISPD_BIT is meaningless. To prevent the setting
wrong bit moves into one condition checking. (e.g sdhci-s3c doesn't use
SDHCI_CTRL_HISPD bit, instead using this bit as other purpose.)
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
When dma->start is failed,then it has to fall back to PIO mode
for current transfer.
But Host controller was already set to bits relevant to DMA operation.
If needs to use the PIO mode, Host controller has to stop the DMA
operation. (It's more stable than now.)
When it occurred error, it's not running any request.
Fixes: 3fc7eaef44 ("mmc: dw_mmc: Add external dma interface support")
Reported-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Reviewed-by: Shawn Lin <shawn.lin@rock-chips.com>
Cc: <stable@vger.kernel.org> # v4.3+
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Since commit 87a18a6a56 ("mmc: mmc: Use ->card_busy() to detect busy
cards in __mmc_switch()") the ESDHC driver is broken:
mmc0: Card stuck in programming state! __mmc_switch
mmc0: error -110 whilst initialising MMC card
Since this commit __mmc_switch() uses ->card_busy(), which is
sdhci_card_busy() for the esdhc driver. sdhci_card_busy() uses the
PRESENT_STATE register, specifically the DAT0 signal level bit. But the
ESDHC uses a non-conformant PRESENT_STATE register, thus a read fixup is
required to make the driver work again.
Signed-off-by: Michael Walle <michael@walle.cc>
Fixes: 87a18a6a56 ("mmc: mmc: Use ->card_busy() to detect busy cards in __mmc_switch()")
Acked-by: Yangbo Lu <yangbo.lu@nxp.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Cc: <stable@vger.kernel.org> # v4.8+
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
An interrupt may occur right after devm_request_irq() is called and
prior to the spinlock initialization, leading to a kernel oops,
as the interrupt handler uses the spinlock.
In order to prevent this problem, move the spinlock initialization
prior to requesting the interrupts.
Fixes: e4243f13d1 (mmc: mxs-mmc: add mmc host driver for i.MX23/28)
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Reviewed-by: Marek Vasut <marex@denx.de>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
In the eMMC 4.51 version of the spec, an EXT_CSD field called
GENERIC_CMD6_TIME[248] was added. This allows cards to specify the maximum
time it may need to move out from its busy state, when a CMD6 command has
been sent.
In cases when the card is compliant to versions < 4.51 of the eMMC spec,
obviously the core needs to use a fall-back value for this timeout, which
currently is set to 10 minutes. This value is completely in the wrong range
and importantly in some cases it causes a card initialization to take more
than 10 minute to complete.
Earlier this scenario was avoided as the mmc core used CMD13 to poll the
card, to find out when it stopped signaling busy. Commit 08573eaf1a
("mmc: mmc: do not use CMD13 to get status after speed mode switch")
changed this behavior.
Instead of reverting that commit, which would cause other issues, let's
instead start by picking a simple solution for the problem, by using a
500ms default generic CMD6 timeout.
The reason for using exactly 500ms, comes from observations that shows it's
quite common for cards to specify 250ms. 500ms is two times that value so
likely it should be enough for most cards.
Cc: <stable@vger.kernel.org> # v4.8+
Fixes: 08573eaf1a ("mmc: mmc: do not use CMD13 to get status after speed
mode switch")
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Tested-by: Stephen Boyd <sboyd@codeaurora.org>
Tested-by: Linus Walleij <linus.walleij@linaro.org>
mmc_test_check_result_async() requires that struct mmc_async_req is
contained within struct mmc_test_async_req. Fix the "Commands during
non-blocking write" tests so that is the case.
Fixes: 4bbb9aac9a ("mmc: mmc_test: Add tests for sending commands during transfer")
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Tested-by: Ritesh Harjani <riteshh@codeaurora.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
To prevent subsequent commands failing, ensure the cmd and data circuits
are reset after a tuning timeout.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
In the busy response case (i.e. !host->data), an unexpected data interrupt
would result in clearing the data command as though it had completed but
without informing the upper layers and thus resulting in a hang. Fix by
only clearing the data command for data interrupts that are expected.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Cc: stable@vger.kernel.org # v4.8+
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
CMD line reset during an ongoing data transfer can cause the data transfer
to hang. Fix by delaying the reset until the data transfer is finished.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Cc: stable@vger.kernel.org # v4.8+
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Add the "reset" as name of reset controller.
This is for preventing the wrong operation. Even if some SoC has reset
controller, doesn't define "resets" in device-tree.
Then it might be waiting for reset controller and it should be stuck.
Fixes: d6786fefe8 ("mmc: dw_mmc: add reset support to dwmmc host controller")
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Acked-by: John Stultz <john.stultz@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
A lot of the REQ_* flags are only used on struct requests, and only of
use to the block layer and a few drivers that dig into struct request
internals.
This patch adds a new req_flags_t rq_flags field to struct request for
them, and thus dramatically shrinks the number of common requests. It
also removes the unfortunate situation where we have to fit the fields
from the same enum into 32 bits for struct bio and 64 bits for
struct request.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Shaun Tancheff <shaun.tancheff@seagate.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
Fix to return a negative error code from the platform_get_irq_byname()
error handling case instead of 0, as done elsewhere in this function.
Fixes: ad81d38710 ("mmc: sdhci-msm: Add support for UHS cards")
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Acked-by: Georgi Djakov <georgi.djakov@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
platform_get_resource can be returned the NULL pointer.
Then regs->start should be referred to NULL Pointer.
devm_ioremap_resource() checks whether res is NULL or not.
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Reviewed-by: Shawn Lin <shawn.lin@rock-chips.com>
Cc: stable@vger.kernel.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Accesses of the rtsx sdmmc's parent device, which is the rtsx usb device,
must be done when it's runtime resumed. Currently this isn't case when
changing the led, so let's fix this by adding a pm_runtime_get_sync() and
a pm_runtime_put() around those operations.
Reported-by: Ritesh Raj Sarraf <rrs@researchut.com>
Tested-by: Ritesh Raj Sarraf <rrs@researchut.com>
Cc: <stable@vger.kernel.org>
Cc: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The rtsx_usb_sdmmc driver may bail out in its ->set_ios() callback when no
SD card is inserted. This is wrong, as it could cause the device to remain
runtime resumed when it's unused. Fix this behaviour.
Tested-by: Ritesh Raj Sarraf <rrs@researchut.com>
Cc: <stable@vger.kernel.org>
Cc: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Potentially overflowing expression 1000000 * data->timeout_clks with
type unsigned int is evaluated using 32-bit arithmetic, and then used
in a context that expects an expression of type unsigned long long.
To avoid overflow, cast 1000000U to type unsigned long long.
Special thanks to Coverity.
Fixes: 7f05538af7 ("mmc: sdhci: fix data timeout (part 2)")
Signed-off-by: Haibo Chen <haibo.chen@nxp.com>
Cc: stable@vger.kernel.org # v3.15+
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
- The DMA error interrupt bit is in a different position as
compared to the sdhci standard. This is accounted for in
many cases, but not handled in the case of clearing the
INT_STATUS register by writing a 1 to that location.
- The HOST_CONTROL register is very different as compared to
the sdhci standard. This is accounted for in the write
case, but not when read back out (which it is in the sdhci
code).
Signed-off-by: Dave Russell <david.russell@datasoft.com>
Signed-off-by: Aaron Brice <aaron.brice@datasoft.com>
Acked-by: Dong Aisheng <aisheng.dong@nxp.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Some Intel controllers (e.g. BXT) might fail to set bus power after a
D3 -> D0 transition due to the present state not yet having propagated.
Retry for up to 2 milliseconds.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Let devices define their own sdhci_ops so that device-specific variations
can be implemented without adding quirks.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Unlike other cases, sdhci_set_power() does not reflect the default
implementation of the ->set_power() callback. Rename it and create
sdhci_set_power() that is the default implementation.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Cc: Jisheng Zhang <jszhang@marvell.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Multi-block data transfers can specify the number of blocks either using a
Set Block Count command (CMD23) or by sending a STOP command (CMD12) after
the required number of blocks has transferred. CMD23 is preferred, but some
cards don't support it. CMD12 with R1b response is used for writes, and
R1 response for reads.
Some SDHCI host controllers give a Transfer Complete (TC) interrupt for the
STOP command (CMD12) whether or not a R1b response has been specified. The
quirk SDHCI_QUIRK2_STOP_WITH_TC identifies those host controllers, but the
implementation only considers the case where the TC interrupt arrives at
the same time as the Command Complete (CC) interrupt. However,
occasionally TC arrives before CC. That is harmless, but does generate an
error message "Got data interrupt 0x00000002 even though no data operation
was in progress".
A simpler approach is to force R1b response onto all STOP commands, because
SDHCI will handle TC before CC in the general case, so do that.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Cc: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Per the vendor's requirement, we shouldn't do any setting for
1.8V Signaling Enable, otherwise the interaction/behaviour between
phy and controller will be undefined. Mostly it works fine if we do
that, but we still see failures. Anyway, let's fix it to meet the
vendor's requirement. The error log looks like:
[ 93.405085] mmc1: unexpected status 0x800900 after switch
[ 93.408474] mmc1: switch to bus width 1 failed
[ 93.408482] mmc1: mmc_select_hs200 failed, error -110
[ 93.408492] mmc1: error -110 during resume (card was removed?)
[ 93.408705] PM: resume of devices complete after 213.453 msecs
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Per JESD84-B51 P49, Host need to change frequency to <=52MHz
after setting HS_TIMING to 0x1, and host may changes frequency
to <= 200MHz after setting HS_TIMING to 0x3. That means the card
expects the clock rate to increase from the current used f_init
(which is less than 400KHz, but still being less than 52MHz) to
52MHz, otherwise we find some eMMC devices significantly report
failure when sending status.
Reported-by: Xiao Yao <xiaoyao@rock-chips.com>
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
When introducing hs400es, I didn't notice that we haven't
switched voltage to 1V2 or 1V8 for it. That happens to work
as the first controller claiming to support hs400es, arasan(5.1),
which is designed to only support 1V8. So the voltage is fixed to 1V8.
But it actually is wrong, and will not fit for other host controllers.
Let's fix it.
Fixes: commit 81ac2af657 ("mmc: core: implement enhanced strobe support")
Cc: <stable@vger.kernel.org>
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
We get 1 warning when building kernel with W=1:
drivers/mmc/card/block.c:2147:5: warning: no previous prototype for
'mmc_blk_issue_rq' [-Wmissing-prototypes]
In fact, this function is declared in drivers/mmc/card/block.h, so this
patch adds missing header dependencies.
Signed-off-by: Baoyou Xie <baoyou.xie@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Fixes the following sparse warning:
drivers/mmc/host/sdhci-of-arasan.c:253:6: warning:
symbol 'sdhci_arasan_reset' was not declared. Should it be static?
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Acked-by: Sören Brinkmann <soren.brinkmann@xilinx.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Remvoe the deprecated "supports-highspeed" property.
DWMMC controller will not use this property anymore.
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Reviewed-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
msize and rx_wmark are properly initialized, we dont't
need to assign them again.
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
It's very prone to make mistake as we might forget
to replace all PAGE_SIZEs with new values if we try
to modify the ring buffer size for whatever reasons.
Let's use a macro to define it.
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The original log didn't figure out that we could still
finish this transfer by PIO mode even if failing to use
DMA. And it should be kept for debug level instead of
error one.
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
We could see an obvious race condition by test that
the former write operation by IDMAC aiming to clear
OWN bit reach right after the later configuration of
the same desc, which makes the IDMAC be in SUSPEND
state as the OWN bit was cleared by the asynchronous
write operation of IDMAC. The bug can be very easy
reproduced on RK3288 or similar when we reduce the
running rate of system buses and keep the CPU running
faster. So as two separate masters, IDMAC and cpu
write the same descriptor stored on the same address,
and this should be protected by adding check of OWN
bit before preparing new descriptors.
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
We intend to add more check for descriptors when
preparing desc. Let's spilt out the separate body
to make the dw_mci_translate_sglist not so lengthy.
After spliting out these two functions, we could
remove dw_mci_translate_sglist and call both of them
when staring idmac.
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Per spec, block size should always be 512 bytes for dual rate mode,
so any attempts to switch the block size under dual rate mode should
be neglected.
Signed-off-by: Ziyuan Xu <xzy.xu@rock-chips.com>
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The sdhci controller on xilinx zynq devices will not function unless
the CD bit is provided. http://www.xilinx.com/support/answers/61064.html
In cases where it is impossible to provide the CD bit in hardware,
setting the controller to test mode and then setting inserted to true
will get the controller to function without the CD bit.
When the device has the property xlnx,fails-without-test-cd the driver
changes the controller to test mode and sets test inserted to true to
make the controller function.
Signed-off-by: Zach Brown <zach.brown@ni.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
We need to add R1 without CRC support, refactor the bus width routine a
little and extend a quirk check. To support "non-removable;" we need a
workaround which will be hopefully removed when reworking PM soon.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
We have enough vtables in the kernel as it is, we don't need
this one to create even more artificial separation of concerns.
As is proved by the Makefile:
obj-$(CONFIG_MMC_BLOCK) += mmc_block.o
mmc_block-objs := block.o queue.o
block.c and queue.c are baked into the same mmc_block.o object.
So why would one of these objects access a function in the
other object by dereferencing a pointer?
Create a new block.h header file for the single shared function
from block to queue and remove the function pointer and just
call the queue request function.
Apart from making the code more readable, this also makes link
optimizations possible and probably speeds up the call as well.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Set MMC_CAP_CMD_DURING_TFR for Intel BYT and related eMMC host controllers.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Set MMC_CAP_CMD_DURING_TFR for Intel BYT and related eMMC host controllers.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Now SDHCI supports commands during transfer, enable support for the core
API.
There are 3 small changes needed:
First, auto-CMD12 cannot be used with a cap_cmd_during_tfr request because
the host controller cannot expect the command line to be available.
Secondly, a cap_cmd_during_tfr request must not send a stop command, again
because the host controller cannot expect the command line to be available.
Thirdly, when a cap_cmd_during_tfr command completes, use
mmc_command_complete() to notify the upper layers that the command line is
now available for further commands.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Add 6 tests for sending commands during transfer. The tests are:
* Commands during read - no Set Block Count (CMD23).
* Commands during write - no Set Block Count (CMD23).
* Commands during read - use Set Block Count (CMD23).
* Commands during write - use Set Block Count (CMD23).
* Commands during non-blocking read - use Set Block Count (CMD23).
* Commands during non-blocking write - use Set Block Count (CMD23).
For a range of transfer sizes, the tests start an ongoing data transfer and
then repeatedly send the status command (CMD13) while the transfer
continues. The tests pass if all requests complete with no errors. The host
controller driver must support MMC_CAP_CMD_DURING_TFR.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
A host controller driver exposes its capability using caps flag
MMC_CAP_CMD_DURING_TFR. A driver with that capability can accept requests
that are marked mrq->cap_cmd_during_tfr = true. Then the driver informs the
upper layers when the command line is available for further commands by
calling mmc_command_done(). Because of that, the driver will not then
automatically send STOP commands, and it is the responsibility of the upper
layer to send a STOP command if it is required.
For requests submitted through the mmc_wait_for_req() interface, the caller
sets mrq->cap_cmd_during_tfr = true which causes mmc_wait_for_req() in fact
not to wait. The caller can then send commands that do not use the data
lines. Finally the caller can wait for the transfer to complete by calling
mmc_wait_for_req_done() which is now exported.
For requests submitted through the mmc_start_req() interface, the caller
again sets mrq->cap_cmd_during_tfr = true, but mmc_start_req() anyway does
not wait. The caller can then send commands that do not use the data
lines. Finally the caller can wait for the transfer to complete in the
normal way i.e. calling mmc_start_req() again.
Irrespective of how a cap_cmd_during_tfr request is started,
mmc_is_req_done() can be called if the upper layer needs to determine if
the request is done. However the appropriate waiting function (either
mmc_wait_for_req_done() or mmc_start_req()) must still be called.
The implementation consists primarily of a new completion
mrq->cmd_completion which notifies when the command line is available for
further commands. That completion is completed by mmc_command_done().
When there is an ongoing data transfer, calls to mmc_wait_for_req() will
automatically wait on that completion, so the caller does not have to do
anything special.
Note, in the case of errors, the driver may call mmc_request_done() without
calling mmc_command_done() because mmc_request_done() always calls
mmc_command_done().
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Clear incorrect SDHCI_CAN_64BIT capability on Broadcom MIPS based SoCs.
The MIPS based SoCs are using ADMA only, but the several SoCs have the
incorrect capability bit about ADMA 64-bit. The "brcm,bcm7425-sdhci" is
compatible string for MIPS based SoC.
Signed-off-by: Jaedon Shin <jaedon.shin@gmail.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
A64 SoC features a MMC controller which need only the mod clock, and can
calibrate delay by itself. This patch adds support for the new MMC
controller IP core.
Signed-off-by: Icenowy Zheng <icenowy@aosc.xyz>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
In most cases the 'card->erase_size' is power of 2, then the round_up/down()
function is more efficient than '%' operation when the 'card->erase_size' is
power of 2.
Signed-off-by: Baolin Wang <baolin.wang@linaro.org>
Tested-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
In order to clean up the mmc_erase() function and do some optimization
for erase size alignment, factor out the guts of erase size alignment
into mmc_align_erase_size() function.
Signed-off-by: Baolin Wang <baolin.wang@linaro.org>
Tested-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
platform_get_irq() returns an error value on failure, not NO_IRQ,
so the error handling here could never work.
This changes the code to propagate the error value instead.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
In cases when the host->max_busy_timeout isn't specified, the calculated
number of maximum discard sectors defaults to UINT_MAX. This may cause a
too long timeout for a discard request.
Avoid this by using a default maximum erase timeout of 60s, used when we
calculate the maximum number of sectors that are allowed to be discarded
per request.
Do note that the minimum number of sectors to be discarded is still at
least one "preferred erase size".
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Reviewed-by: Shawn Lin <shawn.lin@rock-chips.com>
According to the TRM, the SD/MMC controller on Tegra124 supports 34-bit
addressing, but testing shows that this doesn't work. On a device which
has more than 2 GiB of RAM and LPAE enabled, buffer allocations can use
addresses above the 32-bit boundary.
One way to work around this would be to enable IOMMU physical to virtual
address translations for the SD/MMC controllers, but that's not easy to
implement without breaking existing use-cases. It's also not obvious why
34-bit addressing doesn't work as advertised. In order to fix this for
existing users, add the SDHCI_QUIRK2_BROKEN_64_BIT_DMA quirk for now.
Reported-by: Paul Kocialkowski <contact@paulk.fr>
Acked-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
corecfg_clockmultiplier indicates clock multiplier value of
programmable clock generator which should be the same value
of SDHCI_CAPABILITIES_1. The default value of the register,
corecfg_clockmultiplier, is 0x10. But actually it is a mistake
by designer as our intention was to set it to be zero which
means we don't support programmable clock generator. So we have
to make it to be zero on bootloader which seems work fine until
now. But now we find an issue that when deploying genpd support
for it, the remove callback will trigger the genpd to poweroff the
power domain for sdhci-of-arasan which manage the controller, phy
and corecfg_* stuff.
So when we do bind/unbind the driver, we have already reinit
the controller and phy, but without doing that for corecfg_*.
Regarding to only the corecfg_clockmultipler is wrong, let's
fix it by explicitly marking it to be zero when probing. With
this change, we could do bind/unbind successfully.
Reported-by: Ziyuan Xu <xzy.xu@rock-chips.com>
Cc: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Reviewed-by: Ziyuan Xu <xzy.xu@rock-chips.com>
Tested-by: Ziyuan Xu <xzy.xu@rock-chips.com>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Intel Merrifield provides an interface to an external SD card.
Enable it here.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Intel Merrifield is known to have an SDIO interface and on Intel Edison board a
WiFi card is wired to it.
Enable the interface here to allow WiFi card enumeration.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Refactor intel_mrfld_mmc_probe_slot() to use switch case. The change allows to
add a support for SD and SDIO interfaces without any pain.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Hisilicon Hikey have no tuning function in dw_mmc-k3.c,
so we must do the tuning function stub when we init UHS card.
Signed-off-by: Jin Guojun <kid.jin@hisilicon.com>
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The following log we found indicate the fact that dw_mmc
didn't treat EBE or SBE as a similar problem as CRC error.
-EIO is quite not informative as it may indicate that the device
is broken rather than that of tuning stuff.
...
[ 89.057226] bcmsdh_sdmmc: Failed to Read byte F1:@0x1001f=ff, Err: -5
[ 89.058811] bcmsdh_sdmmc: Failed to Read byte F1:@0x1001f=ff, Err: -5
[ 89.059415] bcmsdh_sdmmc: Failed to Read byte F1:@0x1000e=ff, Err: -84
[ 89.254248] dwmmc_rockchip fe310000.dwmmc: Successfully tuned phase to 199
[ 89.273912] dhd_set_suspend: Remove extra suspend setting
[ 89.274478] dhd_enable_packet_filter: enter, value = 0
64 bytes from 112.90.83.112: icmp_seq=24 ttl=53 time=1321 ms
64 bytes from 112.90.83.112: icmp_seq=25 ttl=53 time=319 ms
64 bytes from 112.90.83.112: icmp_seq=26 ttl=53 time=69.8 ms
64 bytes from 112.90.83.112: icmp_seq=27 ttl=53 time=37.5 ms
...
For the host, when failing to sample cmd's response due to
tuning stuff, we still return -EIO as it's quite vague to figure
out whether it related to signal or just the broken devices, especially
for the card type detection when booting kernel as all things go well
but the cmd set used.
But for the data phase, if receiving the cmd's response which
carriess data transfer, we should have more confidence that it
is very probably related to the tuning stuff.
Just as the log shown above, we sometimes suffer too much
this kind of pain as the dw_mmc return -EIO for the case, so
mmc-core will not do retune and caller drivers like bcm's wifi
driver, still retry the failure more and more until dw_mmc
finally generate CRC.
Adrian suggested that drivers who care the specific cases should
call mmc_retune_needed rather than doing it in mmc core. It makes
sense but I'm considering that -EILSEQ actually means illegal sequence
, so we use it for CRC cases. Meanwhile, SBE/EBE indicate the illegal
sequence of start bit or end bit for data0~7. So I realize that we should
use -EILSEQ for them both as well CRC cases.
Suggested-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Dwmmc host controller may in unknown state when entering kernel boot. One
example is when booting from eMMC, bootloader need initialize MMC host
controller into some state so it can read. In order to make sure MMC host
controller in a clean initial state, this reset support is added.
With this patch, a 'resets' property can be added into dw_mmc device
tree node. The hardware logic is: dwmmc host controller IP receives a reset
signal from a 'reset provider' (eg. power management unit). The 'resets'
property points to this reset signal. So, during dwmmc driver probe,
it can use this signal to reset itself.
Refer to [1] for more information.
[1] Documentation/devicetree/bindings/reset/reset.txt
Signed-off-by: Guodong Xu <guodong.xu@linaro.org>
Signed-off-by: Xinwei Kong <kong.kongxinwei@hisilicon.com>
Signed-off-by: Zhangfei Gao <zhangfei.gao@linaro.org>
Reviewed-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
If ciu/biu clock are NULL, clk_disable_unprepare should be just
returned. In clk_disable_unprepare(), already checked whether clk is
error or NULL.
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Reviewed-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The intention to remove it comes from the conflict of
what the mmc-core does with the way dw_mmc treats disable-wp.
We could see that 'disable-wp' is supported by core but
it's deprecated by dw_mmc as we don't expect it to be existed
for each slot subnode but should be in the parent node. Based
on searching for all the upstream dts using dw_mmc, we're
confident that none of them use the deprecated way. Maybe
we should take old dtb in consideration but it was a flag day
since the time we was considering to take it away. The fact is
that there are none of dts using the deprecated way since v3.18
or even earlier. So personally I don't believe the old dtb
would/could bootup current kernel(may not?). Let's remove it now.
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Chipsets before Exynos5420 did not support HS400 so if MMC core tries to
configure HS400 timing, this might or might not work. Warn in such
cases because this is DTB misconfiguration.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Reviewed-by: Alim Akhtar <alim.akhtar@samsung.com>
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
CMD23 aka SET_BLOCK_COUNT was introduced with MMC v3.1.
Older versions of the specification allowed to terminate
multi-block transfers only with CMD12.
The patch fixes the following problem:
mmc0: new MMC card at address 0001
mmcblk0: mmc0:0001 SDMB-16 15.3 MiB
mmcblk0: timed out sending SET_BLOCK_COUNT command, card status 0x400900
...
blk_update_request: I/O error, dev mmcblk0, sector 0
Buffer I/O error on dev mmcblk0, logical block 0, async page read
mmcblk0: unable to read partition table
Signed-off-by: Daniel Glöckner <dg@emlix.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The commit 1ef5e49e46 ("mmc: sdhci-of-esdhc: add/remove some quirks
according to vendor version") moved sdhci-of-esdhc away from using the
->platform_init() callback.
As it was the only user of it and that it seems reasonable to believe that
it won't be needed again, let's just remove it.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
The commit 52ac7acf41 ("mmc: sdhci-pci: Convert to use managed functions
pcim_* and devm_*") converted ->probe() / ->remove() functions to use device
managed resource API. Here is a follow up to cover sdhci_pci_probe_slot() and
sdhci_pci_remove_slot().
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
When using mmc_io_rw_extended, it's intent to avoid null
pointer of card and invalid func number. But actually it
didn't prevent that as the seg_size already use the card.
Currently the wrapper function sdio_io_rw_ext_helper already
use card before calling mmc_io_rw_extended, so we should move
this check to there. As to the func number, it was token from
'(ocr & 0x70000000) >> 28' which should be enough to guarantee
that it won't be larger than 7. But we should prevent the
caller like wifi drivers modify this value. So let's move this
check into sdio_io_rw_ext_helper either.
Also we remove the BUG_ON for mmc_send_io_op_cond since all
possible paths calling this function are protected by checking
the arguments in advance. After deploying these changes, we
could not see any panic within SDIO API even if func drivers
abuse the SDIO func APIs.
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
packed should always exist without calling its cleanup function
explicitly. Moreover, we have use it when preparing packed list.
So I don't believe we should ever fall into this check again when
doing mmc_blk_packed_hdr_wrq_prep or mmc_blk_end_packed_req,etc.
And the code of mmc_blk_end_packed_req is trying to use packed before
checking it which makes it quite weird. This patch is trying to
remove these two checks and move it to the mmc_blk_prep_packed_list.
If we find packed is null, then we should never use MMC_BLK_PACKED_CMD.
By doing this, we could fall back to non-packed request if finding null
packed, though it's impossible theoretically.
After removing these two BUG_ONs, we also remove all other similar
checks within the routine of mmc_blk_issue_rw_rq which checks the
error handling of packed request.
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The switch failure message in mmc_select_timing() had been removed
since that is invalid: commit 0400ed0a08 ("mmc: core: remove the
invalid message in mmc_select_timing")
Now, in the case when mmc_select_hs() return error in mmc_select_timing(),
there is nothing to print failure message.
Let's make for mmc_select_hs() print message itself in the failure case.
Signed-off-by: Jungseung Lee <js07.lee@samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Populating card_busy caused a side-effect on a chip variant we don't
have documentation for (r8a73a4). So, enable it and voltage switching
only on devices known to support those features.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Tested-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Fixes: 452e5eef6d ("mmc: tmio: Add UHS-I mode support")
card_busy is only used/tested on SDHI for R-Car Gen2 and later.
Move it to the SDHI driver, so we can then activate it conditionally
depending on the SDHI type.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Tested-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The sunxi-mmc driver does not take into account the processor may be big
endian when writing the DMA descriptors. This causes cards not to be
detected when running a big-endian kernel. Change the descriptors for
IDMA to use __le32 and ensure they are suitably swapped before writing.
Tested successfully on the Cubieboard2.
Signed-off-by: Michael Weiser <michael.weiser@gmx.de>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Cc: Ulf Hansson <ulf.hansson@linaro.org>
Cc: Chen-Yu Tsai <wens@csie.org>
Cc: linux-mmc@vger.kernel.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
clk_round_rate() may return an error. Check it.
Signed-off-by: Jean-Francois Moine <moinejf@free.fr>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
PHY intended to be used with the Arasan SDHCI 5.1 controller has trouble
turning on when the card clock is slow or off. Strangely these problems
appear to show up consistently on some boards while other boards work
fine, but on the boards where it shows up the problem reproduces 100% of
the time and is quite consistent in its behavior.
These problems can be fixed by always making sure that we power on the
PHY (and turn on its DLL) when the card clock is faster than about 50
MHz. Once on, we need to make sure that we never power down the PHY /
turn off its DLL until the clock is faster again.
We'll add logic for handling this into the sdhci-of-arasan driver. Note
that right now the only user of a PHY in the sdhci-of-arasan driver is
arasan,sdhci-5.1. It's presumed that all arasan,sdhci-5.1 PHY
implementations need this workaround, so the logic is only contingent on
having a PHY to control. If future Arasan controllers don't have this
problem we can add code to decide if we want this flow or not.
Also note that we check for slow clocks by checking for <= 400 kHz
rather than checking for 50 MHz. This keeps things the most consistent
and also means we can power the PHY on at max speed (where the DLL will
lock fastest). Presumably anyone who intends to run with a card clock
of < 50 MHz and > 400 kHz will be running on a device where this problem
is fixed anyway.
I believe this brings some resolution to the problems reported before.
See the commit 6fc09244d7 ("mmc: sdhci-of-arasan: Revert: Always power
the PHY off/on when clock changes").
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Reviewed-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
wait_event_interruptible_timeout() will return early if the blocked
process receives a signal, causing the driver to abort the tuning
procedure and possibly leaving the controller in a bad state. Since the
tuning command is expected to complete quickly (<50ms) and we've set a
timeout, use wait_event_timeout() instead.
Signed-off-by: Christopher Freeman <cfreeman@nvidia.com>
Tested-by: Robert Foss <robert.foss@collabora.com>
Signed-off-by: Robert Foss <robert.foss@collabora.com>
Reviewed-by: Benson Leung <bleung@chromium.org>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
i.MX USDHC Reference Manual has a mistake, for the register SYS_CTRL,
the DTOCV(bit 19~16) means the data timeout counter value. When DTOCV
is set to 0xF, it means SDCLK << 29, not SDCLK << 28.
Signed-off-by: Haibo Chen <haibo.chen@nxp.com>
Acked-by: Dong Aisheng <aisheng.dong@nxp.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Now, when call esdhc_set_timeout() to set the data timeout counter value,
IPP_RST_N(bit 23) is wrongly affected. This patch add a mask to avoid this.
Signed-off-by: Haibo Chen <haibo.chen@nxp.com>
Acked-by: Dong Aisheng <aisheng.dong@nxp.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The field "owner" is set by core. Thus delete an extra initialisation.
Generated by: scripts/coccinelle/api/platform_no_drv_owner.cocci
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The SD Status register contains several important fields related to the
SD Card proprietary features.
Those fields may be used by user space applications for vendor specific
usage.
None of those fields are exported today by the driver to user space.
In this patch, we are reading the SD Status register and exporting
(using MMC_DEV_ATTR) the SD Status register to the user space.
Signed-off-by: Uri Yanai <uri.yanai@sandisk.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
kmalloc will print enough information in case of failure.
Signed-off-by: Wolfram Sang <wsa-dev@sang-engineering.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Use of_property_read_bool to check for the existence of a property.
The semantic patch that makes this change is as follows:
(http://coccinelle.lip6.fr/)
// <smpl>
@@
expression e1,e2;
statement S2,S1;
@@
- if (of_get_property(e1,e2,NULL))
+ if (of_property_read_bool(e1,e2))
S1 else S2
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
In clk_set_rate() or clk_prepare_enable() error handling case, the
error return code ret is not set, so sdhci_bcm_kona_probe() return
0 in those error cases.
Signed-off-by: Wei Yongjun <weiyj.lk@gmail.com>
Acked-by: Ray Jui <ray.jui@broadcom.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
wait_for_completion_timeout_interruptible returns long not unsigned long
so dma_time, which is used exclusively here, is changed to long.
Fixes: 1b66e94e6b ("mmc: moxart: Add MOXA ART SD/MMC driver")
Signed-off-by: Nicholas Mc Guire <hofrat@osadl.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Some devices need a while to boot their firmware after providing clks /
de-asserting resets before they are ready to receive sdio commands.
This commits adds a post-power-on-delay-ms devicetree property to
mmc-pwrseq-simple for use with such devices.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
It turns out that sun4i (A10) and sun5i (A13 & co) do not have sample
clocks, so add a new sun7i-a20-mmc compatible and do not try to use
sample clocks on sun4i / sun5i.
Since sun4i / sun5i do not have sample clocks, they cannot (reliably) do
DDR rates, so only set MMC_CAP_1_8V_DDR when we do have sample clks.
Note this patch leaves the clk_prepare_enable() / clk_disable_unprepare()
calls to the sample clks as-is, without adding checks for them being
NULL. All the clk_foo calls accept a NULL clk and will return success when
called with a NULL clk.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Adrian Hunter