Add support for the FDB add, delete, and dump operations. The add and
delete operations are implemented using directed ARL operations using
the specified MAC address and consist in a read operation, write and
readback operation.
The dump operation consists in using the ARL search and software
filtering entries which are not for the desired port.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The comparison check between cur_hw_state and hw_state is currently
invalid because cur_hw_state is right shifted by G_MISTP_SHIFT, while
hw_state is not, so we end-up comparing bits 2:0 with bits 7:5, which is
going to cause an additional aging to occur. Fix this by not shifting
cur_hw_state while reading it, but instead, mask the value with the
appropriately shitfted bitmask.
The other problem with the fast-ageing process is that we did not set
the EN_AGE_DYNAMIC bit to request the ageing to occur for dynamically
learned MAC addresses. Finally, write back 0 to the FAST_AGE_CTRL
register to avoid leaving spurious bits sets from one operation to the
other.
Fixes: 12f460f234 ("net: dsa: bcm_sf2: add HW bridging support")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
net/bridge/br_mdb.c
br_mdb.c conflict was a function call being removed to fix a bug in
'net' but whose signature was changed in 'net-next'.
Signed-off-by: David S. Miller <davem@davemloft.net>
The SF2 driver currently overrides speed settings for its port
configured using a fixed PHY, this is both unnecessary and incorrect,
because we keep feedback to the hardware parameters that we read from
the PHY device, which in the case of a fixed PHY cannot possibly change
speed.
This is a required change to allow the fixed PHY code to allow
registering a PHY with a link configured as DOWN by default and avoid
some sort of circular dependency where we require the link_update
callback to run to program the hardware, and we then utilize the fixed
PHY parameters to program the hardware with the same settings.
Fixes: 246d7f773c ("net: dsa: add Broadcom SF2 switch driver")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
7445E0 contains an ECO which disconnected the internal SF2 pseudo-PHY which was
known to conflict with the external pseudo-PHY of BCM53125 switches. This
motivated the need to utilize the internal SF2 MDIO controller via indirect
register reads/writes to control external Broadcom switches due to this address
conflict (both responded at address 30d).
For 7445E0, the internal pseudo-PHY of the SF2 switch got disconnected, and as
a consequence this prevents the internal SF2 MDIO bus controller from reading
data (reads back everything as 0) since the MDI line is tied low.
Fix this by making the indirect register reads and writes conditional to
7445D0, on 7445E0 we can utilize the SWITCH_MDIO controller (backed by
mdio-unimac and not the DSA created slave MII bus).
We utilize of_machine_is_compatible() here since this is the only way for use
to differentiate between these two chips in a way that does not violate layers
or becomes (too) vendor-specific.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Utilize the newly introduced BRCM_PSEUDO_PHY_ADDR constant from
brcmphy.h instead of open-coding the Broadcom Ethernet switches
pseudo-PHY address (30).
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
MoCA interfaces require the use of an user-space daemon (mocad) which
will typically use cmd->autoneg to force the link. This is causing other
network manager applications not to get proper carrier down
notifications because of the following sequence of events:
- link down interrupt is received, link is set to 0 by the interrupt
handler
- fixed_link update callback runs and updates the BMSR register
accordingly
- PHY library polls the PHY for link status, sees the link is down,
proceeds with reporting that
- mocad gets notified of the link state and call phy_ethtool_sset()
with cmd->autoneg set to the link status (0)
- phy_start_aneg() is called at the end of phy_ethtool_sset() and sets
the PHY state to PHY_FORCING
Just make sure we notify the interface carrier appropriately when we
detect that the link is down in our fixed_link update callback. This is
made local to the bcm_sf2 driver as the PHY library does the right thing
in any case. This is similar to the GENET change introduced in
54d7c01d3e ("net: bcmgenet: enable MoCA
link state change detection").
Fixes: 246d7f773c ("net: dsa: add Broadcom SF2 switch driver")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Implement the bridge join, leave and set_stp callbacks by making that
we do the following:
- when a port joins the bridge, all existing ports in the bridge get
their VLAN control register updated with that joining port
- the joining port is including all existing bridge ports in its own
VLAN control register
The leave operation is fairly similar, special care must be taken to
make sure that port leaving the bridging is not removing itself from its
own VLAN control register.
Since the various BR_* states apply directly to our HW semantics, we
just need to translate these constants into their corresponding HW
settings, and voila!
We make sure to trigger a fast-ageing process for ports that are
joining/leaving the bridge and transition from incompatible states, this
is equivalent to triggering an ARL flush for that port.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Implement the power on/off recommended procedure for the Single GPHY we
have on our Starfighter 2 switch. In order to make sure we get proper
LED link/activity signaling during suspend, switch the link indication
from the Switch/MAC to the PHY.
Finally, since the GPHY needs to be reset to be put in low power mode,
we will loose any context applied to it: workarounds, EEE etc.. so we
need to call phy_init_hw() to get our fixups re-applied successfully.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move the code that touches the single GPHY register from
bcm_sf2_sw_resume() to a separate function since we will have to
enable/disable the GPHY from different locations, and we want the code
to be self-contained.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Factor the interrupt disabling in a function: bcm_sf2_intr_disable()
since we are doing the same thing in the setup and suspend paths.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For ports of the switch that we define as "fixed PHYs" such as MoCA, we
would have our Port 7 special handling that would allow us to assert the
link status indication.
For other ports, such as e.g: RGMII_1 connected to a cable modem, we
would rely on whatever the bootloader has left configured, which is a
bad assumption to make, we really need to force the link status
indication here.
Fixes: 246d7f773c ("net: dsa: add Broadcom SF2 switch driver")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Our boot agent may have left the switch in an certain configuration
state, make sure we issue a software reset prior to configuring the
switch in order to ensure the HW is in a consistent state, in particular
transmit queues and internal buffers.
Fixes: 246d7f773c ("net: dsa: add Broadcom SF2 switch driver")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In case we fail to ioremap() one of our registers, we would be leaking
existing mappings, unwind those accordingly on errors.
Fixes: 246d7f773c ("net: dsa: add Broadcom SF2 switch driver")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When EEE is enabled, negotiate this feature with the PHY and make sure
that the capability checking, local EEE advertisement, link partner EEE
advertisement and auto-negotiation resolution returned by phy_init_eee()
is positive, and enable EEE at the switch level.
While querying the current EEE settings, verify the low-power indication
and indicate its status.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The SF2 switch driver is already architected around per-port
enable/disable callbacks, so we just need a slight update to our
existing bcm_sf2_port_setup() resp. bcm_sf2_port_disable() functions to
be suitable as callbacks for port_enable/port_disable.
We need to shuffle a little the code that does the per-port VLAN
configuration/isolation since ports can now be brought up/down
separately, so we need to make sure that IMP (CPU, management) port is
always included in that specific port setup.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When the link is down, disable the RGMII interface to conserve as much
power as possible. We re-enable the RGMII interface whenever the link is
detected.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In order for Wake-on-LAN to work properly, we query the parent network
device Wake-on-LAN features and advertise those. Similarly, when
configuring Wake-on-LAN on a per-port network interface, we make sure
that we do not accept something the master network devices does not
support.
Finally, we need to maintain a bitmask of the ports enabled for
Wake-on-LAN to prevent the suspend() callback from disabling a port that
is used for waking up the system.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Implement the suspend/resume callbacks for the Broadcom Starfighter 2
switch driver. Suspending the switch requires masking interrupts and
shutting down ports. Resuming the switch requires a software reset since
we do not know which power-sate we might be coming from, and re-enabling
the physical ports that are used.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The integrated BCM7xxx PHY contains no useful revision information
in its MII_PHYSID2 bits 3:0, that information is instead contained in
the SWITCH_REG_PHY_REVISION register.
Read this register, store its value, and return it by implementing the
dsa_switch::get_phy_flags() callback accordingly. The register layout is
already matching what the BCM7xxx PHY driver is expecting to find.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This change makes it so that instead of passing and storing a mii_bus we
instead pass and store a host_dev. From there we can test to determine the
exact type of device, and can verify it is the correct device for our switch.
So for example it would be possible to pass a device pointer from a pci_dev
and instead of checking for a PHY ID we could check for a vendor and/or device
ID.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that we introduced an additional multiplexing/demultiplexing layer
with commit 3e8a72d1da ("net: dsa: reduce number of protocol hooks")
that lives within the DSA code, we no longer need to have a given switch
driver tag_protocol be an actual ethertype value, instead, we can
replace it with an enum: dsa_tag_protocol.
Do this replacement in the drivers, which allows us to get rid of the
cpu_to_be16()/htons() dance, and remove ETH_P_BRCMTAG since we do not
need it anymore.
Suggested-by: Alexander Duyck <alexander.duyck@gmail.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for the Broadcom Starfigther 2 switch chip using a DSA
driver. This switch driver supports the following features:
- configuration of the external switch port interface: MII, RevMII,
RGMII and RGMII_NO_ID are supported
- support for the per-port MIB counters
- support for link interrupts for special ports (e.g: MoCA)
- powering up/down of switch memories to conserve power when ports are
unused
Finally, update the compatible property for the DSA core code to match
our switch top-level compatible node.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Florian Fainelli