Expose model and fw_version via sysfs. Also query the model
in probe to make sure, that the I2C communication with the
device works before successfully probing the driver.
This is a bit complicated, since EETI devices do not have
a sync interface. Sending the commands and directly reading
does not work. Sending the command and waiting for some time
is also not an option, since there might be touch events in
the mean time.
Last but not least we do not cache the results, since this
interface can be used to check the I2C communication is still
working as expected.
Reviewed-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Link: https://lore.kernel.org/r/20200805160520.456570-5-sebastian.reichel@collabora.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Add basic support for an optional reset gpio.
Reviewed-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Acked-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20200805160520.456570-4-sebastian.reichel@collabora.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
This adds support for EXC80H60 and EXCH84 controllers, which
use a different event type id and have two extra bits for the
resolution (so the maximum is 16K instead of 4K).
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Acked-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20200805160520.456570-3-sebastian.reichel@collabora.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Based on 2 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license version 2 as
published by the free software foundation
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license version 2 as
published by the free software foundation #
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference in 4122 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Enrico Weigelt <info@metux.net>
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Allison Randal <allison@lohutok.net>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190604081206.933168790@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The 3000 series have a new protocol which allows to report up to 5 points
in a single 66 byte frame. One must always read in 66 byte frames.
To support up to 10 points, two consecutive frames need to be read:
The first frame says how many points until sync.
The second frame must say zero points or both frames must be discarded.
To be able to work with the higher 400KHz I2C bus rate, one must
successfully send a special package prior _each_ read or the controller
will refuse to cooperate.
This is a minimal implementation based on egalax_i2c.c (which can be found
on the internet) and egalax_ts.c but without the vendor interface and no
power management support.
Signed-off-by: Ahmet Inan <inan@distec.de>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>