Most DAPM input and output pins of the wm8750 are either used in the card's
DAPM routing table or are marked as not connected. The only exceptions are
the LINPUT1, RINPUT1, LINPUT2 input pins. Lets assume that those were
simply overlooked and that the routing table is complete.
Set the fully_routed flag of the card instead of manually marking the
unused inputs and outputs as not connected. This makes the code a bit
shorter and cleaner.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
Most DAPM input and output pins of the wm9712 are either used in the card's
DAPM routing table or are marked as not connected. The only two exception
are "PHONE" and "PCBEEP" input, lets assume that those were simply
overlooked and that the routing table is complete.
Set the fully_routed flag of the card instead of manually marking the
unused inputs and outputs as not connected. This makes the code a bit
shorter and cleaner.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
The Zaurus SL-5600 seems to have a microphone input. Otherwise all DAPM
input and output pins of the wm8731 are either used in the card's DAPM
routing table or are marked as not connected.
So add the microphone to the DAPM tables and set the fully_routed flag of
the card instead of manually marking the unused inputs and outputs as not
connected. This makes the code a bit shorter and cleaner.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
Most DAPM input and output pins of the wm8994 are either used in the card's
DAPM routing table or are marked as not connected.
The only exception is DMIC2DAT input. Given that DMIC1DAT is explicitly
mentioned in the DAPM routes lets assume that DMIC2DAT simply has been
overlooked and should be marked as not connected.
Set the fully_routed flag of the card instead of manually marking the
unused inputs and outputs as not connected. This makes the code a bit
shorter and cleaner.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
The jacks are card level elements so use snd_soc_card_jack_new() instead of
snd_soc_jack_new() to register them.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
The jacks are card level elements so use snd_soc_card_jack_new() instead of
snd_soc_jack_new() to register them.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
The jacks are card level elements so use snd_soc_card_jack_new() instead of
snd_soc_jack_new() to register them.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
The jacks are card level elements so use snd_soc_card_jack_new() instead of
snd_soc_jack_new() to register them.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
In a rare combination of Kconfig settings, the 88pm860x-codec
module may be selected as a loadable module, while it's also being
used by the ttb-dkb code that is built-in, resulting in a link
error:
sound/built-in.o: In function `ttc_pm860x_init':
:(.text+0x3e888): undefined reference to `pm860x_hs_jack_detect'
:(.text+0x3e898): undefined reference to `pm860x_mic_jack_detect'
Changing ttb-tkb to a tristate option tells Kconfig that 88pm86x
actually needs to be built-in if ttc-dkb is also built-in.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
Commit f6b2a04590 ("ASoC: pxa: mioa701_wm9713: Convert to table based DAPM
setup") converted the driver to register the board level DAPM elements with
the card's DAPM context rather than the CODEC's DAPM context. The change
overlooked that the speaker widget event callback accesses the widget's
codec field which is only valid if the widget has been registered in a CODEC
DAPM context. This patch modifies the callback to take an alternative route
to get the CODEC.
Fixes: f6b2a04590 ("ASoC: pxa: mioa701_wm9713: Convert to table based DAPM
setup")
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
All DAPM input and output pins of the wm8750 are either used in the card's
DAPM routing table or are marked as not connected.
Set the fully_routed flag of the card instead of manually marking the unused
inputs and outputs as not connected. This makes the code a bit shorter and
cleaner.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
All DAPM input and output pins of the wm9712 are either used in the card's
DAPM routing table or are marked as not connected.
Set the fully_routed flag of the card instead of manually marking the unused
inputs and outputs as not connected. This makes the code a bit shorter and
cleaner.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
All DAPM input and output pins of the uda1380 are either used in the card's
DAPM routing table or are marked as not connected.
Set the fully_routed flag of the card instead of manually marking the unused
inputs and outputs as not connected. This makes the code a bit shorter and
cleaner.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
All DAPM input and output pins of the ak4641 are either used in the card's
DAPM routing table or are marked as not connected.
Set the fully_routed flag of the card instead of manually marking the unused
inputs and outputs as not connected. This makes the code a bit shorter and
cleaner.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
All DAPM input and output pins of the wm9705 are either used in the card's
DAPM routing table or are marked as not connected.
Set the fully_routed flag of the card instead of manually marking the unused
inputs and outputs as not connected. This makes the code a bit shorter and
cleaner.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
All DAPM input and output pins of the wm9705 are either used in the card's
DAPM routing table or are marked as not connected.
Set the fully_routed flag of the card instead of manually marking the unused
inputs and outputs as not connected. This makes the code a bit shorter and
cleaner.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
All DAPM input and output pins of the wm8994 are either used in the card's
DAPM routing table or are marked as not connected.
Set the fully_routed flag of the card instead of manually marking the unused
inputs and outputs as not connected. This makes the code a bit shorter and
cleaner.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
The "Headset Mic 2" and the "Headset Stereophone" widget are managed by the
jack detection logic. Their will be set depending on whether something is
connected to the jack or not. There is no need to manually change the state
beforehand as it will be overwritten anyway.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
Set the dai_fmt field in the dai_link struct instead of manually calling
snd_soc_dai_fmt(). This makes the code cleaner and shorter.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
Set the dai_fmt field in the dai_link struct instead of manually calling
snd_soc_dai_fmt(). This makes the code cleaner and shorter.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
This platform_driver does not need to set an owner, it will be populated by the
driver core.
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
Here's the set of driver core patches for 3.19-rc1.
They are dominated by the removal of the .owner field in platform
drivers. They touch a lot of files, but they are "simple" changes, just
removing a line in a structure.
Other than that, a few minor driver core and debugfs changes. There are
some ath9k patches coming in through this tree that have been acked by
the wireless maintainers as they relied on the debugfs changes.
Everything has been in linux-next for a while.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iEYEABECAAYFAlSOD20ACgkQMUfUDdst+ylLPACg2QrW1oHhdTMT9WI8jihlHVRM
53kAoLeteByQ3iVwWurwwseRPiWa8+MI
=OVRS
-----END PGP SIGNATURE-----
Merge tag 'driver-core-3.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull driver core update from Greg KH:
"Here's the set of driver core patches for 3.19-rc1.
They are dominated by the removal of the .owner field in platform
drivers. They touch a lot of files, but they are "simple" changes,
just removing a line in a structure.
Other than that, a few minor driver core and debugfs changes. There
are some ath9k patches coming in through this tree that have been
acked by the wireless maintainers as they relied on the debugfs
changes.
Everything has been in linux-next for a while"
* tag 'driver-core-3.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core: (324 commits)
Revert "ath: ath9k: use debugfs_create_devm_seqfile() helper for seq_file entries"
fs: debugfs: add forward declaration for struct device type
firmware class: Deletion of an unnecessary check before the function call "vunmap"
firmware loader: fix hung task warning dump
devcoredump: provide a one-way disable function
device: Add dev_<level>_once variants
ath: ath9k: use debugfs_create_devm_seqfile() helper for seq_file entries
ath: use seq_file api for ath9k debugfs files
debugfs: add helper function to create device related seq_file
drivers/base: cacheinfo: remove noisy error boot message
Revert "core: platform: add warning if driver has no owner"
drivers: base: support cpu cache information interface to userspace via sysfs
drivers: base: add cpu_device_create to support per-cpu devices
topology: replace custom attribute macros with standard DEVICE_ATTR*
cpumask: factor out show_cpumap into separate helper function
driver core: Fix unbalanced device reference in drivers_probe
driver core: fix race with userland in device_add()
sysfs/kernfs: make read requests on pre-alloc files use the buffer.
sysfs/kernfs: allow attributes to request write buffer be pre-allocated.
fs: sysfs: return EGBIG on write if offset is larger than file size
...
Setting the ac97_control field on a CPU DAI tells the ASoC core that this
DAI in addition to audio data also transports control data to the CODEC.
This causes the core to suspend the DAI after the CODEC and resume it before
the CODEC so communication to the CODEC is still possible. This is not
necessarily something that is specific to AC'97 and can be used by other
buses with the same requirement. This patch renames the flag from
ac97_control to bus_control to make this explicit.
While we are at it also change the type from int to bool.
The following semantich patch was used for automatic conversion of the
drivers:
// <smpl>
@@
identifier drv;
@@
struct snd_soc_dai_driver drv = {
- .ac97_control
+ .bus_control
=
- 1
+ true
};
// </smpl>
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
Change clk_enable/disable() calls to clk_prepare_enable() and
clk_disable_unrepapre().
Signed-off-by: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Properly use snd_soc_update_bits() instead of manually calling the CODEC
driver's read and write callbacks. The later will stop working once the
wm9713 driver has been converted to regmap.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
Use snd_soc_register_card() instead of creating a "soc-audio" platform device.
Signed-off-by: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Pull slave-dmaengine updates from Vinod Koul:
"For dmaengine contributions we have:
- designware cleanup by Andy
- my series moving device_control users to dmanegine_xxx APIs for
later removal of device_control API
- minor fixes spread over drivers mainly mv_xor, pl330, mmp, imx-sdma
etc"
* 'for-linus' of git://git.infradead.org/users/vkoul/slave-dma: (60 commits)
serial: atmel: add missing dmaengine header
dmaengine: remove FSLDMA_EXTERNAL_START
dmaengine: freescale: remove FSLDMA_EXTERNAL_START control method
carma-fpga: move to fsl_dma_external_start()
carma-fpga: use dmaengine_xxx() API
dmaengine: freescale: add and export fsl_dma_external_start()
dmaengine: add dmaengine_prep_dma_sg() helper
video: mx3fb: use dmaengine_terminate_all() API
serial: sh-sci: use dmaengine_terminate_all() API
net: ks8842: use dmaengine_terminate_all() API
mtd: sh_flctl: use dmaengine_terminate_all() API
mtd: fsmc_nand: use dmaengine_terminate_all() API
V4L2: mx3_camer: use dmaengine_pause() API
dmaengine: coh901318: use dmaengine_terminate_all() API
pata_arasan_cf: use dmaengine_terminate_all() API
dmaengine: edma: check for echan->edesc => NULL in edma_dma_pause()
dmaengine: dw: export probe()/remove() and Co to users
dmaengine: dw: enable and disable controller when needed
dmaengine: dw: always export dw_dma_{en,dis}able
dmaengine: dw: introduce dw_dma_on() helper
...
add NO_PERIOD_WAKEUP to PCM INFO, which supports audio no IRQ mode
Signed-off-by: Qiao Zhou <zhouqiao@marvell.com>
Acked-by: Mark Brown <broonie@linaro.org>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
This mode is unsupported, as the DMA controller can't do zero-padding
of samples.
Signed-off-by: Daniel Mack <zonque@gmail.com>
Reported-by: Johannes Stezenbach <js@sig21.net>
Signed-off-by: Mark Brown <broonie@linaro.org>
Cc: stable@vger.kernel.org
There is a small memory leak if probe() fails.
Fixes: 2023c90c3a ('ASoC: pxa: pxa-ssp: add DT bindings')
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
From e7a94bb7fb871c73cc85712d89c1f48d0271c1be Mon Sep 17 00:00:00 2001
From: Arnd Bergmann <arnd@arndb.de>
Date: Thu, 5 Jun 2014 12:31:28 +0200
Subject: [PATCH] ASoC: MMP audio needs sram support
Building the pxa/mmp audio driver without support for the mmp
sram driver enabled results in this link error:
sound/built-in.o: In function `mmp_pcm_free_dma_buffers':
:(.text+0x3e734): undefined reference to `sram_get_gpool'
sound/built-in.o: In function `mmp_pcm_new':
:(.text+0x3e7c0): undefined reference to `sram_get_gpool'
The sram driver is cannot be manually enabled and needs to
be turned on by selecting MMP_SRAM from each module that
needs it, which is what this patch does.
Ideally, MMP should move over to the generic SRAM support, but
for the moment, we can avoid the build error.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Cc: Eric Miao <eric.y.miao@gmail.com>
Cc: Haojian Zhuang <haojian.zhuang@gmail.com>
Cc: Qiao Zhou <zhouqiao@marvell.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
We have in the past added 'depends on I2C' for some of the PXA boards
after hitting randconfig build bugs. I have seens a couple of new
bugs in this area during the linux-next cycle for 3.16, after it
became possible to build some more PXA machines with I2C disabled.
To shut this up for good, this adds the dependency to every board
that uses I2C as the interface to the codec. I have gone through
all board files and verified that they all either use AC97 or
I2C, and this annotates the latter. Some of these already enable
I2C from mach-pxa/Kconfig, but since that can change it's better
to be explicit here.
The link error that can result otherwise happens when CONFIG_I2C
is set to 'm' and the codec driver is built-in as a result of being
selected by the platform specific glue.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
The commit [e1d4d3c8: ASoC: free jack GPIOs before the sound card is
freed] introduced snd_soc_card remove callbacks to a few drivers, but
they are implemented with a wrong argument type. The callback should
receive snd_soc_card pointer instead of snd_soc_pcm_runtime.
Fixes: e1d4d3c854 ('ASoC: free jack GPIOs before the sound card is freed')
Acked-by: Mark Brown <broonie@linaro.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This is the same change as commit fb6b8e7144 "ASoC: tegra: free jack
GPIOs before the sound card is freed", but applied to all other ASoC
machine drivers where code inspection indicates the same problem exists.
That commit's description is:
==========
snd_soc_jack_add_gpios() schedules a work queue item to poll the GPIO to
generate an initial jack status report. If sound card initialization
fails, that work item needs to be cancelled, so it doesn't run after the
card has been freed. Specifically, freeing the card calls
snd_jack_dev_free() which calls snd_jack_dev_disconnect() which sets
jack->input_dev = NULL, and input_dev is used by snd_jack_report(), which
is called from the work queue item.
snd_soc_jack_free_gpios() cancels the work item. The Tegra ASoC machine
drivers do call this function in the platform driver remove() callback.
However, this happens after the sound card is freed, at least when the
card is freed due to errors late during snd_soc_instantiate_card(). This
leaves a window where the work item can execute after the card is freed.
In next-20140522, sound card initialization does fail for unrelated
reasons, and hits the problem described above.
To solve this, fix the Tegra ASoC machine drivers to clean up the Jack
GPIOs during the snd_soc_card's .remove() callback, which is executed
before the overall card object is freed. also, guard the cleanup call
based on whether we actually setup up the GPIOs in the first place.
Ideally, we'd do the cleanup in a struct snd_soc_dai_link .fini/remove
function to match where the GPIOs get set up. However, there is no such
callback.
==========
Note that I have not even compile-tested this in most cases, since most
of the drivers rely on specific mach-* support I don't have enabled, and
don't support COMPILE_TEST. Testing by the relevant board maintainers
would be useful.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Failure to terminate this match table can lead to boot failures
depending on where the compiler places the match table.
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Acked-by: Daniel Mack <zonque@gmail.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
As we are moving the mmp platform towards multiplatform support,
we have to stop including platform header files.
This changes the pxa-ssp sound driver file to no longer depend
on mach/hardware.h and mach/dma.h. The code using the definitions
from those headers is actually gone already, the only thing
that was still being used was the pxa_dma_desc typedef, which
we can easily work around by using the normal 'struct pxa_dma_desc'
name.
The pxa2xx-dma driver still uses this header, so we include it
explicitly there, which is ok because that is only used on pxa,
not on mmp.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Xia Kaixu <kaixu.xia@linaro.org>
Signed-off-by: Mark Brown <broonie@linaro.org>
ALSA SoC core marks widgets as connected by default when they are
initialized in snd_soc_dapm_new_control() so there is no need to call
snd_soc_dapm_enable_pin() from machine driver init functions.
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
ALSA SoC core takes care of calling snd_soc_dapm_sync() at the end
snd_soc_instantiate_card() so there is no need to call it from machine
driver init functions.
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
The missing dependency can lead to build errors, so
make it explicit in Kconfig.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Xia Kaixu <kaixu.xia@linaro.org>
Signed-off-by: Mark Brown <broonie@linaro.org>
Use table based setup to register the controls and DAPM widgets and routes. This
on one hand makes the code a bit shorter and cleaner and on the other hand the
board level DAPM elements get registered in the card's DAPM context rather than
in the CODEC's DAPM context.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
Use table based setup to register the controls and DAPM widgets and routes. This
on one hand makes the code a bit shorter and cleaner and on the other hand the
board level DAPM elements get registered in the card's DAPM context rather than
in the CODEC's DAPM context.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
Lars-Peter Clausen