At the moment we calculate the buffer's pitch with:
pitch = width * DIV_ROUND_UP(bpp, 8)
For CLUT modes with bpp of 1/2/4/8 this gives wrong result, and the
correct pitch is:
pitch = DIV_ROUND_UP(width * bpp, 8)
In practice this doesn't change anything, as we don't support CLUT
modes, but it's better to have the pitch calculation correct.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
The previous commit removed aligning the pitch to SGX's pitch
requirement from align_pitch(). What's left is effectively a function
that returns width * bytespp.
To clean up the driver, we can remove the function and have the
calculation inline in the two places which call align_pitch().
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
omapdrm checks if the pixel stride is divisible by 8. This is meant to
ensure that the byte stride is 32, which is required by SGX.
The check is not correct, as it checks for pixels, not bytes, and thus
needlessly increases the stride for, e.g., NV12.
Also, SGX driver is not supported in the mainline, and the TI's SGX
driver nowadays does the memory allocation itself and doesn't rely on
omapdrm to figure out the correct pitch.
So we can just remove the whole roundup.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
encoder-opa362.c and panel-sharp-ls037v7dw01.c do not use the legacy
GPIO API, so we can remove the including of gpio.h and of_gpio.h.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
* multiple compile break fixes for missing includes, bad kconfig dependencies.
* remove regulator API misuse causing deprecation warnings
* OMAP5 HDMI fixes for DDC and AVI infoframe
* OMAP4 HDMI fix for CEC
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=usqk
-----END PGP SIGNATURE-----
Merge tag 'omapdrm-4.7-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tomba/linux into drm-fixes
omapdrm fixes for 4.7
* multiple compile break fixes for missing includes, bad kconfig dependencies.
* remove regulator API misuse causing deprecation warnings
* OMAP5 HDMI fixes for DDC and AVI infoframe
* OMAP4 HDMI fix for CEC
* tag 'omapdrm-4.7-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tomba/linux:
drm/omap: include gpio/consumer.h where needed
drm/omap: include linux/seq_file.h where needed
Revert "drm/omap: no need to select OMAP2_DSS"
drm/omap: Remove regulator API abuse
OMAPDSS: HDMI5: Change DDC timings
OMAPDSS: HDMI5: Fix AVI infoframe
drm/omap: fix OMAP4 hdmi_core_powerdown_disable()
drm/omap: Fix missing includes
drm/omapdrm: include pinctrl/consumer.h where needed
- add support for reading LVDS panel EDID over DDC
- enable UYVY/VYUY support
- add support for pixel clock polarity configuration
- honor the native-mode DT property for LVDS
- various fixes and cleanups
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=EPQk
-----END PGP SIGNATURE-----
Merge tag 'imx-drm-next-2016-06-01' of git://git.pengutronix.de/git/pza/linux into drm-fixes
imx-drm updates
- add support for reading LVDS panel EDID over DDC
- enable UYVY/VYUY support
- add support for pixel clock polarity configuration
- honor the native-mode DT property for LVDS
- various fixes and cleanups
* tag 'imx-drm-next-2016-06-01' of git://git.pengutronix.de/git/pza/linux:
drm/imx: plane: Don't set plane->crtc in ipu_plane_update()
drm/imx: ipuv3-plane: Constify ipu_plane_funcs
drm/imx: imx-ldb: honor 'native-mode' property when selecting video mode from DT
drm/imx: parallel-display: remove dead code
drm/imx: use bus_flags for pixel clock polarity
drm/imx: ipuv3-plane: enable UYVY and VYUY formats
drm/imx: parallel-display: use of_graph_get_endpoint_by_regs helper
drm/imx: imx-ldb: use of_graph_get_endpoint_by_regs helper
dt-bindings: imx: ldb: Add ddc-i2c-bus property
drm/imx: imx-ldb: Add DDC support
The first one is making use of __drm_atomic_helper_crtc_destroy_state()
instead of duplicating its logic in atmel_hlcdc_crtc_reset() and
risking memory leaks if other objects are added to the common CRTC
state.
The second one is fixing a possible NULL pointer dereference.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=69hd
-----END PGP SIGNATURE-----
Merge tag 'drm-atmel-hlcdc-fixes/for-4.7-rc2' of github.com:bbrezillon/linux-at91 into drm-fixes
Two trivial bugfixes for the atmel-hlcdc driver.
The first one is making use of __drm_atomic_helper_crtc_destroy_state()
instead of duplicating its logic in atmel_hlcdc_crtc_reset() and
risking memory leaks if other objects are added to the common CRTC
state.
The second one is fixing a possible NULL pointer dereference.
* tag 'drm-atmel-hlcdc-fixes/for-4.7-rc2' of github.com:bbrezillon/linux-at91:
drm: atmel-hlcdc: fix a NULL check
drm: atmel-hlcdc: fix atmel_hlcdc_crtc_reset() implementation
"I have accumulated some cleanup patches for HDLCD, partly triggered by
Daniel Vetter's work on non-blocking atomic operations, that I would like
to integrate into v4.7. My first patch is important for the newly enabled
hibernate option for AArch64 on Juno, the others are fixing behaviour in
HDLCD and adding a debugfs entry to help track the underlying framebuffer
usage. I'm also taking one of Daniel's patches from his non-blocking series
to help with the integration of his patches later."
* 'for-upstream/hdlcd' of git://linux-arm.org/linux-ld:
drm: hdlcd: Add information about the underlying framebuffers in debugfs
drm: hdlcd: Cleanup the atomic plane operations
drm/hdlcd: Fix up crtc_state->event handling
drm: hdlcd: Revamp runtime power management
Harden the plane_check() code to drop attempts at scaling because
that is not supported. Make hdlcd_plane_atomic_update() set the pitch
and line length registers that correctly reflect the plane's values.
And make hdlcd_crtc_mode_set_nofb() a helper function for
hdlcd_crtc_enable() rather than an exposed hook.
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Liviu Dudau <Liviu.Dudau@arm.com>
event_list just reimplemented what drm_crtc_arm_vblank_event does. And
we also need to send out drm events when shutting down a pipe.
With this it's possible to use the new nonblocking commit support in
the helpers.
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Acked-by: Liviu Dudau <Liviu.Dudau@arm.com>
Because the HDLCD driver acts as a component master it can end
up enabling the runtime PM functionality before the encoders
are initialised. This can cause crashes if the component slave
never probes (missing module) or if the PM operations kick in
before the probe finishes.
Move the enabling of the runtime PM after the component master
has finished collecting the slave components and use the DRM
atomic helpers to suspend and resume the device.
Tested-by: Robin Murphy <Robin.Murphy@arm.com>
Signed-off-by: Liviu Dudau <Liviu.Dudau@arm.com>
Do not try to dereference dpi if it is NULL.
Since dpi can never be NULL when mtk_dpi_set_display_mode() is called,
remove the message.
Reported-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
If kmalloc() returned NULL we would end up dereferencing "state" a
couple lines later.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Reset crtc->state to NULL after freeing the state object and call
__drm_atomic_helper_crtc_destroy_state() helper instead of manually
calling drm_property_unreference_blob().
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
- Fixed black screen for some resolutions of G200e rev4
- Fixed testm & testn which had predetermined value.
Reported-by: Jan Beulich <jbeulich@suse.com>
Signed-off-by: Mathieu Larouche <mathieu.larouche@matrox.com>
Cc: stable@vger.kernel.org
Signed-off-by: Dave Airlie <airlied@redhat.com>
Since the introduction of (struct_mutex) lockless GEM bo freeing, there
are a pair of driver vfuncs for freeing the GEM bo, of which the driver
may choose to only implement driver->gem_object_free_unlocked (and so
avoid taking the struct_mutex along the free path). However, the CMA GEM
helpers were still calling driver->gem_free_object directly, now NULL,
and promptly dying on the fancy new lockless drivers. Oops.
Robert Foss bisected this to b82caafcf2 (drm/vc4: Use lockless gem BO
free callback) on his vc4 device, but that just serves as an enabler for
9f0ba539d1 (drm/gem: support BO freeing without dev->struct_mutex).
Reported-by: Robert Foss <robert.foss@collabora.com>
Fixes: 9f0ba539d1 (drm/gem: support BO freeing without dev->struct_mutex)
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Robert Foss <robert.foss@collabora.com>
Cc: Daniel Vetter <daniel.vetter@intel.com>
Cc: Eric Anholt <eric@anholt.net>
Cc: Alex Deucher <alexdeucher@gmail.com>
Cc: Lucas Stach <l.stach@pengutronix.de>
Cc: stable@vger.kernel.org
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Tested-by: Robert Foss <robert.foss@collabora.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
After commit 027b3f8ba9 ("drm/modes: stop
handling framebuffer special") extra fb refs are left around when doing
atomic modesetting.
The problem is that the new drm_property_change_valid_get() does not
return anything in the '**ref' parameter, which causes
drm_property_change_valid_put() to do nothing.
For some reason this doesn't cause problems with legacy API.
Also, previously the code only set the 'ref' variable for fbs, with this
patch the 'ref' is set for all objects.
Fixes: 027b3f8ba9 ("drm/modes: stop handling framebuffer special")
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Dave Airlie <airlied@redhat.com>
drm_atomic_set_mode_prop_for_crtc() does not clear the state->mode, so
old data may be left there when a new mode is set, possibly causing odd
issues.
This patch improves the situation by always clearing the state->mode
first.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Cc: stable@vger.kernel.org
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Commit 652353e6e5 ("drm/sti: set CRTC
modesetting parameters") added a hack to avoid warnings related to
setting mode with atomic API. With the previous patch, the hack should
no longer be necessary.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Cc: Benjamin Gaignard <benjamin.gaignard@linaro.org>
Cc: Vincent Abriou <vincent.abriou@st.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Dave Airlie <airlied@redhat.com>
When setting mode via MODE_ID property,
drm_atomic_set_mode_prop_for_crtc() does not call
drm_mode_set_crtcinfo() which possibly causes:
"[drm:drm_calc_timestamping_constants [drm]] *ERROR* crtc 32: Can't
calculate constants, dotclock = 0!"
Whether the error is seen depends on the previous data in state->mode,
as state->mode is not cleared when setting new mode.
This patch adds drm_mode_set_crtcinfo() call to
drm_mode_convert_umode(), which is called in both legacy and atomic
paths. This should be fine as there's no reason to call
drm_mode_convert_umode() without also setting the crtc related fields.
drm_mode_set_crtcinfo() is removed from the legacy drm_mode_setcrtc() as
that is no longer needed.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: stable@vger.kernel.org
Signed-off-by: Dave Airlie <airlied@redhat.com>
A lot of the display drivers for OMAP use the gpio descriptor functions
that are only available in linux/gpio.h if GPIOLIB is enabled and
otherwise produce a build error:
drivers/gpu/drm/omapdrm/displays/encoder-opa362.c: In function 'opa362_enable':
drivers/gpu/drm/omapdrm/displays/encoder-opa362.c:101:3: error: implicit declaration of function 'gpiod_set_value_cansleep' [-Werror=implicit-function-declaration]
drivers/gpu/drm/omapdrm/displays/panel-dpi.c: In function 'panel_dpi_probe_pdata':
drivers/gpu/drm/omapdrm/displays/panel-dpi.c:189:23: error: implicit declaration of function 'gpio_to_desc' [-Werror=implicit-function-declaration]
drivers/gpu/drm/omapdrm/displays/panel-sharp-ls037v7dw01.c: In function 'sharp_ls_enable':
drivers/gpu/drm/omapdrm/displays/panel-sharp-ls037v7dw01.c:120:3: error: implicit declaration of function 'gpiod_set_value_cansleep' [-Werror=implicit-function-declaration]
This replaces the existing linux/gpio.h with linux/gpio/consumer.h
where needed. In case of panel-lgphilips-lb035q02.c however, we
also have to include linux/gpio.h to get the definition of gpio_is_valid
and gpio_set_value_cansleep that are used for the non-DT case.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
[tomi.valkeinen@ti.com: resolved conflicts]
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
The omapdrm driver relies on this header to be included
implicitly, but this does not always work, and I get
this error in randconfig builds:
gpu/drm/omapdrm/dss/hdmi_phy.c: In function 'hdmi_phy_dump':
gpu/drm/omapdrm/dss/hdmi_phy.c:34:2: error: implicit declaration of function 'seq_printf' [-Werror=implicit-function-declaration]
gpu/drm/omapdrm/dss/hdmi_wp.c: In function 'hdmi_wp_dump':
gpu/drm/omapdrm/dss/hdmi_wp.c:26:2: error: implicit declaration of function 'seq_printf' [-Werror=implicit-function-declaration]
gpu/drm/omapdrm/dss/hdmi_pll.c: In function 'hdmi_pll_dump':
gpu/drm/omapdrm/dss/hdmi_pll.c:30:2: error: implicit declaration of function 'seq_printf' [-Werror=implicit-function-declaration]
This adds the #include statements in all files that have
a seq_printf statement.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
This reverts commit 1c278e5e37.
If DRM_OMAP does not select OMAP2_DSS it is possible to build a kernel with
DRM_OMAP only and not selecting OMAP2_DSS. Since omapdrm depends on
OMAP2_DSS this will result on broken kernel build.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
regulator_can_change_voltage() is deprecated and it's use is not necessary
as commit:
6a0028b3dd regulator: Deprecate regulator_can_change_voltage()
describers it clearly.
Also, regulator_set_voltage() is misused in the driver, as it is
supposed to be used only in cases where the regulator voltage needs to
be changed dynamically at runtime. In DSS's case, we always want a fixed
voltage, set in the .dts files.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
The DDC scl high and low times were set to the minimum values
from the i2c specification, but the i2c specification takes into
account the rise time and fall time to calculate the frequency.
To pass HDMI certification DDC can not exceed 100kHz therefore in
a system where the rise times and fall times are negligible the high
and low times for scl need to be 10us.
Signed-off-by: Jim Lodes <jim.lodes@garmin.com>
Signed-off-by: J.D. Schroeder <jay.schroeder@garmin.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
The AVI infoframe R0-R3 in the 2nd data byte represents the
Active Format Aspect Ratio. It is four bits long not two bits.
This fixes that mask used to extract the bits before writing the
bits to the hardware registers.
Signed-off-by: Jim Lodes <jim.lodes@garmin.com>
Signed-off-by: J.D. Schroeder <jay.schroeder@garmin.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
hdmi_core_powerdown_disable() is supposed to disable HDMI core's
power-down mode. However, the function sets the power-down bit to 0,
which means "enable power-down".
This hasn't caused any issues as the PD seems to affect only interrupts
from HDMI core, and none of those interrupts are used at the moment. CEC
functionality requires core interrupts, and the PD mode needs to be
fixed.
This patch fixes hdmi_core_powerdown_disable() to actually disable the
PD mode.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Reported-by: Hans Verkuil <hverkuil@xs4all.nl>
With certain kernel config options many omapdrm files fail to compile
due to missing include of linux/gpio/consumer.h and linux/of.h.
This patch adds those includes.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Reported-by: Dan Murphy <dmurphy@ti.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
In some configurations, we can build the OMAP dss driver without
implictly including the pinctrl consumer definitions, causing
a build error:
gpu/drm/omapdrm/dss/dss.c: In function 'dss_runtime_suspend':
gpu/drm/omapdrm/dss/dss.c:1268:2: error: implicit declaration of function 'pinctrl_pm_select_sleep_state' [-Werror=implicit-function-declaration]
This adds an explicit #include.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Since the drm core sets plane->crtc correctly, we don't need to do that.
Signed-off-by: Liu Ying <gnuiyl@gmail.com>
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
This patch allows to select a specific video mode from a list of modes
defined in DT by setting the 'native-mode' property appropriately.
This change does not affect the behaviour of existing platforms, since
they either:
- have just one display-timings subnode
- have the native-mode property pointing to the first entry
- let the bootloader select the appropriate timing
Signed-off-by: Lothar Waßmann <LW@KARO-electronics.de>
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
The 'mode_valid' flag is never set in this driver. Remove it and the
code that depends on it.
Signed-off-by: Lothar Waßmann <LW@KARO-electronics.de>
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
This patch allows panels to set pixel clock and data enable pin polarity
other than the default of driving data at the falling pixel clock edge
and active high display enable.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Instead of using of_graph_get_port_by_id() to get the port and then
of_get_child_by_name() to get the first endpoint, get to the endpoint
in a single step.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Instead of using of_graph_get_port_by_id() to get the port and then
of_get_child_by_name() to get the first endpoint, get to the endpoint
in a single step.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Add support for reading EDID over Display Data Channel. If no DDC
adapter is available, falls back to hardcoded EDID or display-timings
node as before.
Signed-off-by: Steve Longerbeam <steve_longerbeam@mentor.com>
Signed-off-by: Akshay Bhat <akshay.bhat@timesys.com>
Acked-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Most users of IS_ERR_VALUE() in the kernel are wrong, as they
pass an 'int' into a function that takes an 'unsigned long'
argument. This happens to work because the type is sign-extended
on 64-bit architectures before it gets converted into an
unsigned type.
However, anything that passes an 'unsigned short' or 'unsigned int'
argument into IS_ERR_VALUE() is guaranteed to be broken, as are
8-bit integers and types that are wider than 'unsigned long'.
Andrzej Hajda has already fixed a lot of the worst abusers that
were causing actual bugs, but it would be nice to prevent any
users that are not passing 'unsigned long' arguments.
This patch changes all users of IS_ERR_VALUE() that I could find
on 32-bit ARM randconfig builds and x86 allmodconfig. For the
moment, this doesn't change the definition of IS_ERR_VALUE()
because there are probably still architecture specific users
elsewhere.
Almost all the warnings I got are for files that are better off
using 'if (err)' or 'if (err < 0)'.
The only legitimate user I could find that we get a warning for
is the (32-bit only) freescale fman driver, so I did not remove
the IS_ERR_VALUE() there but changed the type to 'unsigned long'.
For 9pfs, I just worked around one user whose calling conventions
are so obscure that I did not dare change the behavior.
I was using this definition for testing:
#define IS_ERR_VALUE(x) ((unsigned long*)NULL == (typeof (x)*)NULL && \
unlikely((unsigned long long)(x) >= (unsigned long long)(typeof(x))-MAX_ERRNO))
which ends up making all 16-bit or wider types work correctly with
the most plausible interpretation of what IS_ERR_VALUE() was supposed
to return according to its users, but also causes a compile-time
warning for any users that do not pass an 'unsigned long' argument.
I suggested this approach earlier this year, but back then we ended
up deciding to just fix the users that are obviously broken. After
the initial warning that caused me to get involved in the discussion
(fs/gfs2/dir.c) showed up again in the mainline kernel, Linus
asked me to send the whole thing again.
[ Updated the 9p parts as per Al Viro - Linus ]
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Cc: Andrzej Hajda <a.hajda@samsung.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Link: https://lkml.org/lkml/2016/1/7/363
Link: https://lkml.org/lkml/2016/5/27/486
Acked-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org> # For nvmem part
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Pull drm fixes from Dave Airlie:
- one IMX built-in regression fix
- a set of amdgpu fixes, mostly powerplay and polaris GPU stuff
- a set of i915 fixes all over, many cc'ed to stable.
The i915 batch contain support for DP++ dongle detection, which is
used to fix some regressions in the HDMI color depth area
* tag 'drm-fixes-v4.7-rc1' of git://people.freedesktop.org/~airlied/linux: (44 commits)
drm/amd: add Kconfig dependency for ACP on DRM_AMDGPU
drm/amdgpu: Fix hdmi deep color support.
drm/amdgpu: fix bug in fence driver fini
drm/i915: Stop automatically retiring requests after a GPU hang
drm/i915: Unify intel_ring_begin()
drm/i915: Ignore stale wm register values on resume on ilk-bdw (v2)
drm/i915/psr: Try to program link training times correctly
drm/imx: Match imx-ipuv3-crtc components using device node in platform data
drm/i915/bxt: Adjusting the error in horizontal timings retrieval
drm/i915: Don't leave old junk in ilk active watermarks on readout
drm/i915: s/DPPL/DPLL/ for SKL DPLLs
drm/i915: Fix gen8 semaphores id for legacy mode
drm/i915: Set crtc_state->lane_count for HDMI
drm/i915/BXT: Retrieving the horizontal timing for DSI
drm/i915: Protect gen7 irq_seqno_barrier with uncore lock
drm/i915: Re-enable GGTT earlier during resume on pre-gen6 platforms
drm/i915: Determine DP++ type 1 DVI adaptor presence based on VBT
drm/i915: Enable/disable TMDS output buffers in DP++ adaptor as needed
drm/i915: Respect DP++ adaptor TMDS clock limit
drm: Add helper for DP++ adaptors
...
I see the main drm pull got merged, here's the first batch of fixes for
4.7 already. Fixes all around, a large portion cc: stable stuff.
[airlied: the DP++ stuff is a regression fix].
* tag 'drm-intel-next-fixes-2016-05-25' of git://anongit.freedesktop.org/drm-intel:
drm/i915: Stop automatically retiring requests after a GPU hang
drm/i915: Unify intel_ring_begin()
drm/i915: Ignore stale wm register values on resume on ilk-bdw (v2)
drm/i915/psr: Try to program link training times correctly
drm/i915/bxt: Adjusting the error in horizontal timings retrieval
drm/i915: Don't leave old junk in ilk active watermarks on readout
drm/i915: s/DPPL/DPLL/ for SKL DPLLs
drm/i915: Fix gen8 semaphores id for legacy mode
drm/i915: Set crtc_state->lane_count for HDMI
drm/i915/BXT: Retrieving the horizontal timing for DSI
drm/i915: Protect gen7 irq_seqno_barrier with uncore lock
drm/i915: Re-enable GGTT earlier during resume on pre-gen6 platforms
drm/i915: Determine DP++ type 1 DVI adaptor presence based on VBT
drm/i915: Enable/disable TMDS output buffers in DP++ adaptor as needed
drm/i915: Respect DP++ adaptor TMDS clock limit
drm: Add helper for DP++ adaptors
AMD GPU bugfixes:
- Various powerplay bug fixes
- Add some new polaris pci ids
- misc bug fixes and code cleanups
* 'drm-next-4.7' of git://people.freedesktop.org/~agd5f/linux: (27 commits)
drm/amd: add Kconfig dependency for ACP on DRM_AMDGPU
drm/amdgpu: Fix hdmi deep color support.
drm/amdgpu: fix bug in fence driver fini
drm/amd/powerplay/hwmgr: use kmemdup
drm/amd/powerplay/hwmgr: use kmemdup
drm/amd/powerplay/hwmgr: use kmemdup
drm/amd/powerplay: fix bugs of checking if dpm is running on Tonga
drm/amdgpu: update Polaris11 golden setting
drm/amdgpu: Add more Polaris 11 PCI IDs
drm/amdgpu: update Polaris10 golden setting
drm/amdgpu: add more Polaris10 DID
drm/amd/amdgpu : Remove unused variable
drm/amd/amdgpu : Remove unused variable
drm/amd/amdgpu : Remove unused variable
drm/amd/amdgpu/cz_dpm: Remove unused variable
drm/amd/amdgpu : Remove unused variable
drm/amd/powerplay: use ARRAY_SIZE() to calculate array size.
drm/amdgpu: fix array out of bounds
drm/radeon: fix array out of bounds
drm/amd/powerplay: fix a bug on updating sclk for Tonga
...
This set of changes introduces an atomic API to the PWM subsystem. This
is influenced by the DRM atomic API that was introduced a while back,
though it is obviously a lot simpler. The fundamental idea remains the
same, though: drivers provide a single callback to implement the atomic
configuration of a PWM channel.
As a side-effect the PWM subsystem gains the ability for initial state
retrieval, so that the logical state mirrors that of the hardware. Many
use-cases don't care about this, but for others it is essential.
These new features require changes in all users, which these patches
take care of. The core is transitioned to use the atomic callback if
available and provides a fallback mechanism for other drivers.
Changes to transition users and drivers to the atomic API are postponed
to v4.8.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=sxT9
-----END PGP SIGNATURE-----
Merge tag 'pwm/for-4.7-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/thierry.reding/linux-pwm
Pull pwm updates from Thierry Reding:
"This set of changes introduces an atomic API to the PWM subsystem.
This is influenced by the DRM atomic API that was introduced a while
back, though it is obviously a lot simpler. The fundamental idea
remains the same, though: drivers provide a single callback to
implement the atomic configuration of a PWM channel.
As a side-effect the PWM subsystem gains the ability for initial state
retrieval, so that the logical state mirrors that of the hardware.
Many use-cases don't care about this, but for others it is essential.
These new features require changes in all users, which these patches
take care of. The core is transitioned to use the atomic callback if
available and provides a fallback mechanism for other drivers.
Changes to transition users and drivers to the atomic API are
postponed to v4.8"
* tag 'pwm/for-4.7-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/thierry.reding/linux-pwm: (30 commits)
pwm: Add information about polarity, duty cycle and period to debugfs
pwm: Switch to the atomic API
pwm: Update documentation
pwm: Add core infrastructure to allow atomic updates
pwm: Add hardware readout infrastructure
pwm: Move the enabled/disabled info into pwm_state
pwm: Introduce the pwm_state concept
pwm: Keep PWM state in sync with hardware state
ARM: Explicitly apply PWM config extracted from pwm_args
drm: i915: Explicitly apply PWM config extracted from pwm_args
input: misc: pwm-beeper: Explicitly apply PWM config extracted from pwm_args
input: misc: max8997: Explicitly apply PWM config extracted from pwm_args
backlight: lm3630a: explicitly apply PWM config extracted from pwm_args
backlight: lp855x: Explicitly apply PWM config extracted from pwm_args
backlight: lp8788: Explicitly apply PWM config extracted from pwm_args
backlight: pwm_bl: Use pwm_get_args() where appropriate
fbdev: ssd1307fb: Use pwm_get_args() where appropriate
regulator: pwm: Use pwm_get_args() where appropriate
leds: pwm: Use pwm_get_args() where appropriate
input: misc: max77693: Use pwm_get_args() where appropriate
...
The DRM_AMD_ACP option doesn't have any dependencies and selects
MFD_CORE, which results in MFD_CORE=y. Since the code is only called
from DRM_AMDGPU, it should depend on it. Adding the dependency results
in MFD_CORE being selected as a module again if amdgpu is also a module.
Signed-off-by: Jeff Mahoney <jeffm@suse.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
When porting the hdmi deep color detection code from
radeon-kms to amdgpu-kms apparently some kind of
copy and paste error happened, attaching an else
branch to the wrong if statement.
The result is that hdmi deep color mode is always
disabled, regardless of gpu and display capabilities and
user wishes, as the code mistakenly thinks that the display
doesn't provide the required max_tmds_clock limit and falls
back to 8 bpc.
This patch fixes deep color support, as tested on a
R9 380 Tonga Pro + suitable display, and should be
backported to all kernels with amdgpu-kms support.
Signed-off-by: Mario Kleiner <mario.kleiner.de@gmail.com>
Cc: stable@vger.kernel.org
Cc: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Using wrong counter for walking fences. Fixes
a crash when unloading the driver.
Signed-off-by: Monk Liu <Monk.Liu@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Tomi Valkeinen