This allows you to force specific power levels within a power
state. Due to hardware restrictions between generations, the
interface is limited to the following 3 selections:
auto: all levels enabled
low: forced to the lowest power level
high: forced to the highest power level
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Certain older rv770 asics have both a performance and
a 3D performance state rather than just multiple performance
levels in the state power state. The current code would
select the performance state rather than the 3D performance
state when the "performance" profile was selected. This change
switches to the "balanced" profile by default which ends up being
the internal performance profile. When the user selects the
"performance" profile, it selects the internal 3D performance
state so the user can select the higher performance modes.
For most asics this changes nothing. For certain rv770 asics
with static performance and 3D performance states, this allows
you to select between then using by selecting the "balanced"
and "performance" dpm profiles.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Fix patching of vddc values for SI and enable manually forcing
clocks to default levels as per NI.
This improves the out of the box performance with SI asics.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
For chips without debugfs dpm support say that it's not
implemented rather than not supported to avoid confusion
about DPM support in general.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This adds dpm support for SI asics. This includes:
- dynamic engine clock scaling
- dynamic memory clock scaling
- dynamic voltage scaling
- dynamic pcie gen1/gen2/gen3 switching
- power containment
- shader power scaling
Set radeon.dpm=1 to enable.
v2: enable hainan support, rebase
v3: guard acpi stuff
v4: fix 64 bit math
v5: fix 64 bit div harder
v6: fix thermal interrupt check noticed by Jerome
v7: attempt fix state enable
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Now that the proper fix has been implemented I can
remove the last remnants of the initial implementation.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This adds dpm support for cayman asics. This includes:
- clockgating
- dynamic engine clock scaling
- dynamic memory clock scaling
- dynamic voltage scaling
- dynamic pcie gen1/gen2 switching (requires additional acpi support)
- power containment
- shader power scaling
Set radeon.dpm=1 to enable.
v2: fold in tdp fix
v3: fix indentation
v4: fix 64 bit div
v5: attempt to fix state enable
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Jerome Glisse <jglisse@redhat.com>
Use a dedicated copy of the current power state since
we may have to adjust it on the fly.
v2: fix up redundant state sets
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
When using UVD, the driver must switch to a special UVD power
state. In the CS ioctl, switch to the power state and schedule
work to change the power state back, when the work comes up,
check if uvd is still busy and if not, switch back to the user
state, otherwise, reschedule the work.
Note: We really need some better way to decide when to
switch out of the uvd power state. Switching power states
while playback is active make uvd angry.
V2: fix locking.
V3: switch from timer to delayed work
V4: check fence driver for UVD jobs, reduce timeout to
1 second and rearm timeout on activity
v5: rebase on new dpm tree
v6: rebase on interim uvd on demand changes
v7: fix UVD when DPM is disabled
v8: unify non-DPM and DPM UVD handling
v9: remove leftover idle work struct
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Christian König <deathsimple@vodafone.de>
This adds dpm support for trinity asics. This includes:
- clockgating
- powergating
- dynamic engine clock scaling
- dynamic voltage scaling
set radeon.dpm=1 to enable it.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This adds dpm support for sumo asics. This includes:
- clockgating
- powergating
- dynamic engine clock scaling
- dynamic voltage scaling
set radeon.dpm=1 to enable it.
v2: fix indention
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Jerome Glisse <jglisse@redhat.com>
This adds dpm support for rv7xx asics. This includes:
- clockgating
- dynamic engine clock scaling
- dynamic memory clock scaling
- dynamic voltage scaling
- dynamic pcie gen1/gen2 switching
Set radeon.dpm=1 to enable.
v2: reduce stack usage
v3: fix 64 bit div
v4: fix state enable
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This adds dpm support for rv6xx asics. This includes:
- clockgating
- dynamic engine clock scaling
- dynamic memory clock scaling
- dynamic voltage scaling
- dynamic pcie gen1/gen2 switching
Set radeon.dpm=1 to enable.
v2: remove duplicate line
v3: fix thermal interrupt check noticed by Jerome
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
This adds dpm support for rs780/rs880 asics. This includes:
- clockgating
- dynamic engine clock scaling
- dynamic voltage scaling
set radeon.dpm=1 to enable it.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This adds the common dpm (dynamic power management)
infrastructure:
- dpm callbacks
- dpm init/fini/suspend/resume
- dpm power state selection
No device specific code is enabled yet.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
radeon_fence_wait_empty_locked should not trigger GPU reset as no
place where it's call from would benefit from such thing and it
actually lead to a kernel deadlock in case the reset is triggered
from pm codepath. Instead force ring completion in place where it
makes sense or return early in others.
Signed-off-by: Jerome Glisse <jglisse@redhat.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
Pull drm merge (part 1) from Dave Airlie:
"So first of all my tree and uapi stuff has a conflict mess, its my
fault as the nouveau stuff didn't hit -next as were trying to rebase
regressions out of it before we merged.
Highlights:
- SH mobile modesetting driver and associated helpers
- some DRM core documentation
- i915 modesetting rework, haswell hdmi, haswell and vlv fixes, write
combined pte writing, ilk rc6 support,
- nouveau: major driver rework into a hw core driver, makes features
like SLI a lot saner to implement,
- psb: add eDP/DP support for Cedarview
- radeon: 2 layer page tables, async VM pte updates, better PLL
selection for > 2 screens, better ACPI interactions
The rest is general grab bag of fixes.
So why part 1? well I have the exynos pull req which came in a bit
late but was waiting for me to do something they shouldn't have and it
looks fairly safe, and David Howells has some more header cleanups
he'd like me to pull, that seem like a good idea, but I'd like to get
this merge out of the way so -next dosen't get blocked."
Tons of conflicts mostly due to silly include line changes, but mostly
mindless. A few other small semantic conflicts too, noted from Dave's
pre-merged branch.
* 'drm-next' of git://people.freedesktop.org/~airlied/linux: (447 commits)
drm/nv98/crypt: fix fuc build with latest envyas
drm/nouveau/devinit: fixup various issues with subdev ctor/init ordering
drm/nv41/vm: fix and enable use of "real" pciegart
drm/nv44/vm: fix and enable use of "real" pciegart
drm/nv04/dmaobj: fixup vm target handling in preparation for nv4x pcie
drm/nouveau: store supported dma mask in vmmgr
drm/nvc0/ibus: initial implementation of subdev
drm/nouveau/therm: add support for fan-control modes
drm/nouveau/hwmon: rename pwm0* to pmw1* to follow hwmon's rules
drm/nouveau/therm: calculate the pwm divisor on nv50+
drm/nouveau/fan: rewrite the fan tachometer driver to get more precision, faster
drm/nouveau/therm: move thermal-related functions to the therm subdev
drm/nouveau/bios: parse the pwm divisor from the perf table
drm/nouveau/therm: use the EXTDEV table to detect i2c monitoring devices
drm/nouveau/therm: rework thermal table parsing
drm/nouveau/gpio: expose the PWM/TOGGLE parameter found in the gpio vbios table
drm/nouveau: fix pm initialization order
drm/nouveau/bios: check that fixed tvdac gpio data is valid before using it
drm/nouveau: log channel debug/error messages from client object rather than drm client
drm/nouveau: have drm debugging macros build on top of core macros
...
Convert #include "..." to #include <path/...> in drivers/gpu/.
Signed-off-by: David Howells <dhowells@redhat.com>
Acked-by: Dave Airlie <airlied@redhat.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Acked-by: Dave Jones <davej@redhat.com>
Starting on BTC, there are no longer separate states for
single head and multi-head, we just use the high mclk/voltage
for all states for multi-head.
Fixes:
https://bugs.freedesktop.org/show_bug.cgi?id=49981
v2: fix typo
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Driver used to print "default" as the state type regardless
of whether it is the default state.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
SI asics store voltage information differently so we
don't have a way to deal with it properly yet.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
Move it out of the radeon_pm.c and into radeon_acpi.c since
we use it for more than just pm now.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Set up an handler for ACPI events and respond to brightness change
requests from the system BIOS.
v2: fix notification when using device-specific command codes
(tested by Pali Rohár <pali.rohar@gmail.com>); cache the encoder
controlling the backlight during the initialization to avoid searching
it every time (suggested by Alex Deucher).
v3: whitespace fixes (Alex Deucher).
Signed-off-by: Luca Tettamanti <kronos.it@gmail.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
1. Drop gui idle stuff, it's not as reliable as fences and only
covers the 3D engine.
2. Wait for fences on all rings. This makes sure all rings are
idle when reclocking.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
1. It is really dangerous to have more than one
spinlock protecting the same information.
2. radeon_irq_set sometimes wasn't called with lock
protection, so it can happen that more than one
CPU would tamper with the irq regs at the same
time.
3. The pm.gui_idle variable was assuming that the 3D
engine wasn't becoming idle between testing the
register and setting the variable. So just remove
it and test the register directly.
v2: Also handle the hpd irq code the same way.
v3: Rename hpd parameter for clarification.
Signed-off-by: Christian Koenig <christian.koenig@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
It is a rw_semaphore now and only write locked
while changing the clock. Also the lock is renamed
to better reflect what it is protecting.
v2: Keep the ttm_vm_ops on IGPs
Signed-off-by: Christian König <deathsimple@vodafone.de>
Reviewed-by: Jerome Glisse <jglisse@redhat.com>
Not all asics have all rings, so make sure the ring is ready
before attempting to check it in the dynpm work handler.
Fixes:
https://bugzilla.kernel.org/show_bug.cgi?id=43367
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Jerome Glisse <jglisse@redhat.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Some callers illegal called fence_wait_next/empty
while holding the ring emission mutex. So don't
relock the mutex in that cases, and move the actual
locking into the fence code.
v2: Don't try to unlock the mutex if it isn't locked.
Signed-off-by: Christian König <deathsimple@vodafone.de>
Signed-off-by: Dave Airlie <airlied@redhat.com>
A single global mutex for ring submissions seems sufficient.
Signed-off-by: Christian König <deathsimple@vodafone.de>
Signed-off-by: Dave Airlie <airlied@redhat.com>
tidy up radeon_asic struct.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Christian König<christian.koenig@amd.com>
Reviewed-by: Michel Dänzer <michel.daenzer@amd.com>
Reviewed-by: Jerome Glisse <jglisse@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
That naming seems to make more sense, since we not
only want to run PM4 rings with it.
Signed-off-by: Christian König <deathsimple@vodafone.de>
Reviewed-by: Jerome Glisse <jglisse@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Split counting of emited fences out of power
management into a seperate function.
Signed-off-by: Christian König <deathsimple@vodafone.de>
Reviewed-by: Jerome Glisse <jglisse@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Replace cp, cp1 and cp2 members with just an array
of radeon_cp structs.
Signed-off-by: Christian König <deathsimple@vodafone.de>
Reviewed-by: Jerome Glisse <jglisse@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Give all asic and radeon_ring_* functions a
radeon_cp parameter, so they know the ring to work with.
Signed-off-by: Christian König <deathsimple@vodafone.de>
Reviewed-by: Jerome Glisse <jglisse@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
For supporting multiple CP ring buffers, async DMA
engines and UVD. We still need a way to synchronize
between engines.
v2 initialize unused fence driver ring to avoid issue in
suspend/unload
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Christian König <deathsimple@vodafone.de>
Reviewed-by: Jerome Glisse <jglisse@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Better fix it before this obvious typo spreads even more.
Signed-off-by: Christian König <deathsimple@vodafone.de>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Jerome Glisse <jglisse@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
The new power tables need to be handled differently when setting
up the profiles.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Need to add vddci setting to pm init as well as
resume. Fixes hangs on load on some boards.
Fixes:
https://bugs.freedesktop.org/show_bug.cgi?id=38754
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@kernel.org
Signed-off-by: Dave Airlie <airlied@redhat.com>
Change vddci as well as vddc when changing power modes
on evergreen/ni. Also, properly set vddci on boot up
for ni cards. The vbios only sets the limited clocks
and voltages on boot until the mc ucode is loaded. This
should fix stability problems on some btc cards.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
This is needed for setting voltages other than vddc.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Throw an error if someone tries to fill this with
wrong data, instead of simply ignoring the input.
Now you get:
echo hello >/sys/../power_method
-bash: echo: write error: Invalid argument
Signed-off-by: Thomas Renninger <trenn@suse.de>
CC: Alexander.Deucher@amd.com
CC: dri-devel@lists.freedesktop.org
Reviewed-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
We previously used a static array, but some new systems
had more states then we had array space, so dynamically
allocate space based on the number of states in the vbios.
Fixes:
https://bugs.freedesktop.org/show_bug.cgi?id=33851
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Cc: stable@kernel.org
Signed-off-by: Dave Airlie <airlied@redhat.com>
Some fixes to the thermal sensor code:
- handle negative numbers
- properly handle temp calculation on different asics
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
The vbios only partially initializes the memory controller on
NI, so now we need to load the MC ucode in the driver and set
the default clocks once the ucode is loaded.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
NI chips no longer load the MC ucode in the asic_init sequence so
the asic comes up in a basic mode with low engine/memory clocks and
a voltage. Once the MC ucode is loaded by the driver the card
can be programmed to it's proper default clocks and voltage. As such
the default clocks in the firmware info table as the post clocks, not
the default running clocks. Track the default post clocks and default
running clocks separately to handle this.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
With cmwq, there's no reason for radeon to use a dedicated workqueue.
Drop dev_priv->wq and use system_wq instead.
Because radeon_driver_irq_uninstall_kms() may be called from
unsleepable context, the work items can't be flushed from there.
Instead, init and flush from radeon_irq_kms_init/fini().
While at it, simplify canceling/flushing of rdev->pm.dynpm_idle_work.
Always initialize and sync cancel instead of being unnecessarily smart
about it.
Signed-off-by: Tejun Heo <tj@kernel.org>
Acked-by: Alex Deucher <alexdeucher@gmail.com>
Cc: dri-devel@lists.freedesktop.org
Signed-off-by: Dave Airlie <airlied@redhat.com>
* 'drm-radeon-fusion' of ../drm-radeon-next:
drm/radeon/kms: add Ontario APU ucode loading support
drm/radeon/kms: add Ontario Fusion APU pci ids
drm/radeon/kms: enable MSIs on fusion APUs
drm/radeon/kms: add power table parsing support for Ontario fusion APUs
drm/radeon/kms: refactor atombios power state fetching
drm/radeon/kms: add bo blit support for Ontario fusion APUs
drm/radeon/kms: add thermal sensor support for fusion APUs
drm/radeon/kms: fill in GPU init for AMD Ontario Fusion APUs
drm/radeon/kms: add radeon_asic struct for AMD Ontario fusion APUs
drm/radeon/kms: evergreen.c updates for fusion
drm/radeon/kms: MC setup changes for fusion APUs
drm/radeon/kms: move r7xx/evergreen to its own vram_gtt setup function
drm/radeon/kms: add support for ss overrides on Fusion APUs
drm/radeon/kms: Add support for external encoders on fusion APUs
drm/radeon/kms: atom changes for DCE4.1 devices
drm/radeon/kms: add new family id for AMD Ontario APUs
drm/radeon/kms: upstream power table updates
drm/radeon/kms: upstream atombios.h updates
drm/radeon/kms: upstream ObjectID.h updates
drm/radeon/kms: setup mc chremap properly on r7xx/evergreen
This patch adds new functions for use by the drm core:
.get_vblank_timestamp() provides a precise timestamp
for the end of the most recent (or current) vblank
interval of a given crtc, as needed for the DRI2
implementation of the OML_sync_control extension.
It is a thin wrapper around the drm function
drm_calc_vbltimestamp_from_scanoutpos() which does
almost all the work and is shared across drivers.
.get_scanout_position() provides the current horizontal
and vertical video scanout position and "in vblank"
status of a given crtc, as needed by the drm for use by
drm_calc_vbltimestamp_from_scanoutpos().
The function is also used by the dynamic gpu reclocking
code to determine when it is safe to reclock inside vblank.
For that purpose radeon_pm_in_vbl() is modified to
accomodate a small change in the function prototype of
the radeon_get_crtc_scanoutpos() which is hooked up to
.get_scanout_position().
This code has been tested on AVIVO hardware, a RV530
(ATI Mobility Radeon X1600) in a Intel Core-2 Duo MacBookPro
and some R600 variant (FireGL V7600) in a single cpu
AMD Athlon 64 PC.
Signed-off-by: Mario Kleiner <mario.kleiner@tuebingen.mpg.de>
Reviewed-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
radeon_pm_in_vbl() didn't report in vblank status accurately. Make
it a wrapper around radeon_get_crtc_scanoutpos() which corrects for
biases, so it reports accurately.
radeon_pm_in_vbl() will only report in_vbl if all active crtc's
are currently inside vblank.
agd5f: use rdev->num_crtc rather than hardcoding the crtc count
Signed-off-by: Mario Kleiner <mario.kleiner@tuebingen.mpg.de>
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
I missed this one in the i2c unification patch. This
is handled in the core radeon i2c code now.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Smatch complained that the ERR_PTR from hwmon_device_register() wasn't
handled. I added some error handling in radeon_hwmon_init() to silence
the warning.
Unfortunately errors from radeon_pm_init() aren't handled so this
doesn't really make a difference beyond silencing the warning.
Also I changed DRM_ERROR() to dev_err() which is the new preferred
method.
Signed-off-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
* 'intel/drm-intel-next' of /ssd/git/drm-next: (230 commits)
drm/i915: Clear the Ironlake dithering flags when the pipe doesn't want it.
drm/agp/i915: trim stolen space to 32M
drm/i915: Unset cursor if out-of-bounds upon mode change (v4)
drm/i915: Unreference object not handle on creation
drm/i915: Attempt to uncouple object after catastrophic failure in unbind
drm/i915: Repeat unbinding during free if interrupted (v6)
drm/i915: Refactor i915_gem_retire_requests()
drm/i915: Warn if we run out of FIFO space for a mode
drm/i915: Round up the watermark entries (v3)
drm/i915: Typo in (unused) register mask for overlay.
drm/i915: Check overlay stride errata for i830 and i845
drm/i915: Validate the mode for eDP by using fixed panel size
drm/i915: Always use the fixed panel timing for eDP
drm/i915: Enable panel fitting for eDP
drm/i915: Add fixed panel mode parsed from EDID for eDP without fixed mode in VBT
drm/i915/sdvo: Set sync polarity based on actual mode
drm/i915/hdmi: Set sync polarity based on actual mode
drm/i915/pch: Set transcoder sync polarity for DP based on actual mode
drm/i915: Initialize LVDS and eDP outputs before anything else
drm/i915/dp: Correctly report eDP in the core connector type
...
This migrates a bunch of DRM_DEBUG->DRM_DEBUG_KMS so we can get more modesetting related info without all the other ioctl handling easily.
Also the PM code moves to DRM_DEBUG_DRIVER mostly.
Signed-off-by: Dave Airlie <airlied@redhat.com>
rv6xx/rv7xx/evergreen families supported; older asics did
not have an internal thermal sensor.
Note, not all oems use the internal thermal sensor, so it's
only exposed in cases where it is used.
Note also, that most laptops use an oem specific ACPI solution for
GPU thermal information rather than using the internal thermal
sensor directly.
v2: export millidegrees celsius, use hwmon device properly.
v3: fix Kconfig
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Fix incorrectly reporting 'default' power profile, when it is set to 'mid'.
Signed-off-by: Daniel J Blueman <daniel.blueman@gmail.com>
Reviewed-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
There is a regression from 2.6.34 related to the recent radeon power
management changes, caused by attempting to cancel a delayed work
item that's never been scheduled. However, the code as is has some
other issues potentially leading to visible problems.
First, the mutex around cancel_delayed_work() in radeon_pm_suspend()
doesn't really serve any purpose, because cancel_delayed_work() only
tries to delete the work's timer. Moreover, it doesn't prevent the
work handler from running, so the handler can do some wrong things if
it wins the race and in that case it will rearm itself to do some
more wrong things going forward. So, I think it's better to wait for
the handler to return in case it's already been queued up for
execution. Also, it should be prevented from rearming itself in that
case.
Second, in radeon_set_pm_method() the cancel_delayed_work() is not
sufficient to prevent the work handler from running and queing up
itself for the next run (the failure scenario is that
cancel_delayed_work() returns 0, so the handler is run, it waits on
the mutex and then rearms itself after the mutex has been released),
so again the work handler should be prevented from rearming itself in
that case..
Finally, there's a potential deadlock in radeon_pm_fini(), because
cancel_delayed_work_sync() is called under rdev->pm.mutex, but the
work handler tries to acquire the same mutex (if it wins the race).
Fix the issues described above.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Reviewed-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
track the current voltage level and avoid setting it
if the requested voltage is already set.
v2: check voltage type before checking current voltage
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
This adds an additional profile, mid, to the pm profile
code which takes the place of the old low profile. The default
behavior remains the same, e.g., auto profile now selects between
mid and high profiles based on power source, however, you can now
manually force the low profile which was previously only available
as a dpms off state. Enabling the low profile when the displays
are on has been known to cause display corruption in some cases.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
- don't rest the power state in pm_init()
We already boot up to the default power state. Note this
patch relies on:
drm/radeon/kms/pm: patch default power state with default clocks/voltages on r6xx+
To make sure the default power state matches the boot up state.
- In the pm resume path asic init will have set the power state
back to the default so reset the tracking state values.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
PM attemps to unmap objects that aren't actually mapped into userspace ever,
so just don't bother unmapping them at this point, since all you are doing
is nothing. We should be making sure all access to these objects are locked in
kernel space instead. In theory the VRAM gart table is already done, and both
the shaders and stolen vga memory blocks are never accessed at runtime.
fixes: https://bugzilla.kernel.org/show_bug.cgi?id=16127
Reported-by: Jure Repnic <jlp.bugs@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
- wait for vbl for both profile and dynpm
- unify profile and dynpm code paths more
- call pm_misc before of after clocks to make
sure voltage is changed in the proper order.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
- Separate dynpm and profile based power management methods. You can select the pm method
by echoing the selected method ("dynpm" or "profile") to power_method in sysfs.
- Expose basic 4 profile in profile method
"default" - default clocks
"auto" - select between low and high based on ac/dc state
"low" - DC, low power mode
"high" - AC, performance mode
The current base profile is "default", but it should switched to "auto" once we've tested
on more systems. Switching the state is a matter of echoing the requested profile to
power_profile in sysfs. The lowest power states are selected automatically when dpms turns
the monitors off in all states but default.
- Remove dynamic fence-based reclocking for the moment. We can revisit this later once we
have basic pm in.
- Move pm init/fini to modesetting path. pm is tightly coupled with display state. Make sure
display side is initialized before pm.
- Add pm suspend/resume functions to make sure pm state is properly reinitialized on resume.
- Remove dynpm module option. It's now selectable via sysfs.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
The lowest power states often cause display problems, so only enable
them when all displays are off.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
GUI idle interrupts don't seem to work terribly well on r500 and earlier,
so let's use a fence instead.
Signed-off-by: Matthew Garrett <mjg@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
- disable gui idle interrupt use
Seems to hang some r5xx chips
- move vbl range check into
existing vbl check function in
radeon_pm.c
- disable crtc mc acccess for the
whole reclocking process
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
The vblank interrupt on r600 doesn't seem to be especially reliable, so
perform some sanity checks before the actual reclock.
Signed-off-by: Matthew Garrett <mjg@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
The ttm code could take vram_mutex followed by cp_mutex, while the
reclocking code would do the reverse. Hilarity could ensue.
Signed-off-by: Matthew Garrett <mjg@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
We need to choose the correct PM state to transition into before starting
the actual change. Call radeon_get_power_state() at the top of the clock
setting to do so.
Signed-off-by: Matthew Garrett <mjg@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
The ttm bo workqueue may touch objects while we're reclocking, so make
sure it's blocked until we're done.
Signed-off-by: Matthew Garrett <mjg@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
We need to block the drm core from doing anything that may touch our vram
during reclock, so take the drm mutex for the duration.
Signed-off-by: Matthew Garrett <mjg@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Touching vram while the card is reclocking can lead to lockups. Unmap
any pages that could be touched by the CPU and block any accesses to
vram until the reclocking is complete.
Signed-off-by: Matthew Garrett <mjg@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
There's a moderate amount of effort involved in setting the card up for
clock transitions, so unify the codepaths to make it easier to implement.
Signed-off-by: Matthew Garrett <mjg@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Add two new sysfs attributes:
- dynpm
- power_state
Echoing 0/1 to dynpm disables/enables dynamic power management.
The driver scales the sclk dynamically based on the number of
queued fences. dynpm only scales sclk dynamically in single head
mode.
Echoing x.y to power_state selects a static power state (x) and clock
mode (y). This allows you to statically select a power state and clock
mode. Selecting a static clock mode will disable dynpm.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
- remove non_clock_info struct
- track power state misc flags
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Just adds overhead when the power state will never change.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
This also simplifies the code and enables reclocking with multiple heads
active by tracking whether the power states are single or multi-head
capable.
Eventually, we will want to select a power state based on external
factors (AC/DC state, user selection, etc.).
(v2) Update for evergreen
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Alex Deucher