If the CI chip has an I2C driver, we need to store I2C client into state.
Signed-off-by: Olli Salonen <olli.salonen@iki.fi>
Reviewed-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
This patch adds basic support for DVBSky T980C card. CI interface is not supported.
DVBSky T980C is a PCIe card with the following components:
- CX23885 PCIe bridge
- Si2168-A20 demodulator
- Si2158-A20 tuner
- CIMaX SP2 CI chip
The demodulator and tuner need firmware. They're the same as used with TT CT2-4650 CI:
https://www.mail-archive.com/linux-media@vger.kernel.org/msg78033.html
Signed-off-by: Olli Salonen <olli.salonen@iki.fi>
Reviewed-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
DVBSky T9580 is a dual tuner card with one DVB-T2/C tuner and one DVB-S2 tuner. It contains the following components:
- PCIe bridge: Conexant CX23885
- Demod for terrestrial/cable: Silicon Labs Si2168-A30
- Tuner for terrestrial/cable: Silicon Labs Si2158-A20
- Demod for sat: Montage DS3103
- Tuner for sat: Montage TS2022
This patch depends on Max Nibble's patch for m88ds3103 (see patchwork 25312: https://patchwork.linuxtv.org/patch/25312/ ).
3 firmwares are needed:
- Si2168-A30 demod and Si2158-A20 tuner: same as TechnoTrend CT2-4400, https://www.mail-archive.com/linux-media@vger.kernel.org/msg76944.html
- Montage DS3103 demod: same as PCTV 461e, Antti has it on his LinuxTV project page: http://palosaari.fi/linux/v4l-dvb/firmware/M88DS3103/
IR receiver is not supported.
Values in cx23885_gpio_setup, cx23885_card_setup and dvbsky_t9580_set_voltage as well as the EEPROM read function are taken from the manufacturer provided semi-open source driver. The drivers in question are Linux GPL'd media tree drivers for cx23885 modified by Max Nibble (nibble.max@gmail.com) with proprietary tuner/demod drivers. Max is aware of this patch and has approved my use of the values in this patch.
Signed-off-by: Olli Salonen <olli.salonen@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Setting the LNB voltage requires setting some GPIOs on the cx23885 with some boards before calling the actual set_voltage function in the demod driver. Add a function pointer into state for that case.
Signed-off-by: Olli Salonen <olli.salonen@iki.fi>
Acked-by: Antti Palosaari <crope@iki.fi>
Reviewed-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Prepare cx23885 driver for handling I2C client that is needed for certain demodulators and tuners (for example Si2168 and Si2157). I2C client for tuner and demod stored in state and unregistering of the I2C devices added into dvb_unregister.
Signed-off-by: Olli Salonen <olli.salonen@iki.fi>
Reviewed-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The norm_swidth function was unused and is dropped. It's not clear
what the purpose of that function was.
The norm_maxh function was changed so it tests for 60 Hz standards
rather than for 50 Hz standards. The is the preferred order.
The norm_maxw function was poorly written and used: it gives the maximum
allowed line width for the given standard. For 60 Hz that's 720, but
for 50 Hz that's 768 which allows for 768x576 which gives you square
pixels. For 60 Hz formats it is 640x480 that gives square pixels, so
there is no need to go beyond 720.
The initial width was set using norm_maxh(), which was wrong. Just set
to 720, that's what you normally use. Since the initial standard was
NTSC anyway the initial width was always 720 anyway.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
It's just as easy to do it in the driver. This dependency only uses a
fraction of the btcx-risc module and doing it directly in the driver
adds only a few lines. The btcx-risc module is really meant for the
bttv driver, not for other drivers.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
As usual, this patch is very large due to the fact that half a vb2 conversion
isn't possible. And since this affects 417, alsa, core, dvb, vbi and video the
changes are all over.
What made this more difficult was the peculiar way the risc program was setup.
The driver allowed for running out of buffers in which case the DMA would stop
and restart when the next buffer was queued. There was also a complicated
timeout system for when buffers weren't filled. This was replaced by a much
simpler scheme where there is always one buffer around and the DMA will just
cycle that buffer until a new buffer is queued. In that case the previous
buffer will be chained to the new buffer. An interrupt is generated at the
start of the new buffer telling the driver that the previous buffer can be
passed on to userspace.
Much simpler and more robust. The old code seems to be copied from the
cx88 driver. But it didn't fit the vb2 ops very well and replacing it with
the new scheme made the code easier to understand. Not to mention that this
patch removes 600 lines of code.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
These addresses are usually out-of-date and the top-level license will
always have the right address. So drop it from these sources.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Use video_drvdata(file) instead of fh->dev to get the cx23885_dev
pointer. This prepares for the vb2 conversion where fh->dev (renamed
to fh->q_dev in this patch) will be removed completely.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
The alsa driver uses videobuf low-level functions that are not
available in vb2, so replace them by driver-specific functions.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Move these fields from cx23885_fh to cx23885_dev.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
There is no overlay support, so drop these unused fields.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
This information is available elsewhere as well.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Currently no radio device nodes are ever created, so remove the dead radio
code.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Convert the -417 source to the control framework as well.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
This is part 1, converting the uncompressed video/vbi nodes to use
the control framework.
The next patch converts the compressed video node as well.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Add support for struct v4l2_fh and priority handling.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Add support for Hauppauge model 71100: WinTV-ImpactVCB-e
(PCIe, Retail, half height)
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Tested:
Composite: http://imgur.com/Rb1TCF3
TV: http://imgur.com/KNrfsmv
Firmware used: xc3028-v27.fw
Not tested: audio, component, s-video, mpeg2 encoder, FM radio.
For audio, it uses an CD style cable to connect to the analog "CD_IN" on the motherboard.
I didn't found how to unmute it (alsamixer do not show an CD or AUX channel).
Signed-off-by: Anca Emanuel <anca.emanuel@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
When the frontend drivers got converted to DVBv5 API, the original
hook that tracked when a frontend is set got removed, being replaced
by an approach that would use the gate control. That doesn't work
fine with some boards. Also, the code were called more times than
desired.
Replace it by a logic that will hook the dvb set_frontend ops,
with works with both DVBv3 and DVBv5 calls.
Tested on a Mygica X8502 OEM board.
Tested-by: Alfredo Delaiti <alfredodelaiti@netscape.net>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
This ioctl is defined as IOW, so pass the argument as const.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch provide only analog support.
The device is based on AF9013 demodulator, XC3028 tuner
and CX23885 chipset; subsystem id: 1461:d939
Signed-off-by: Oleh Kravchenko <oleg@kaa.org.ua>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add basic DVB-S2 support for the Hauppauge HVR-4400 PCIe board.
Thanks to Antti Palosaari and Devin Heitmueller for their
suggestions and testing.
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Reviewed-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Reviewed-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The device is based on STV0903 demodulator, STB6100 tuner
and CX23885 chipset; subsystem id: 8000:3034
This is a modified version of the official Prof Tuners Group patch:
http://www.proftuners.com/sites/default/files/prof8000_0.patch
[mchehab@redhat.com: trivial merge conflict fixup]
Signed-off-by: Mariusz Bialonczyk <manio@skyboo.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Rename all PCI drivers with their own directory under
drivers/media/video into drivers/media/pci and update the
building system.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Olli Salonen