This device uses GPIOs: 28 to switch between analog and
digital modes: on digital mode, it should be set to 1.
The code that sets it on analog mode is OK, but it misses
the logic that sets it on digital mode.
Cc: stable@vger.kernel.org
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The cx231xx_set_agc_analog_digital_mux_select() callers
expect it to return 0 or an error. Returning a positive value
makes the first attempt to switch between analog/digital to fail.
Cc: stable@vger.kernel.org
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
With the current settings, only one channel locks properly.
That's likely because, when this driver was written, Brazil
were still using experimental transmissions.
Change it to reproduce the settings used by the newer drivers.
That makes it lock on other channels.
Tested with both PixelView SBTVD Hybrid (cx231xx-based) and
C3Tech Digital Duo HDTV/SDTV (em28xx-based) devices.
Cc: stable@vger.kernel.org
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
On this frontend, it takes a while to start output normal
TS data. That only happens on state S9. On S8, the TS output
is enabled, but it is not reliable enough.
However, the zigzag loop is too fast to let it sync.
As, on practical tests, the zigzag software loop doesn't
seem to be helping, but just slowing down the tuning, let's
switch to hardware algorithm, as the tuners used on such
devices are capable of work with frequency drifts without
any help from software.
Cc: stable@vger.kernel.org
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
use pr_fmt() & friends for error messages to output like:
[ 9.651721] tea5767: Chip ID is not zero. It is not a TEA5767
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Some messages have a hardcoded prefix; others not. Use the
pr_fmt() to ensure that all messages will use the same prefix.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
* 'docs-next' of git://git.lwn.net/linux:
doc-rst: define PDF's of the media folder
doc-rst: generic way to build PDF of sub-folders
docs: sphinx-extensions: add metadata parallel-safe
docs-rst: kernel-doc: fix typedef output in RST format
docs-rst: improve typedef parser
docs: kernel-parameter: Improve the description of nr_cpus and maxcpus
docs-rst: kernel-doc: better output struct members
To build only the PDF of the media folder run::
make SPHINXDIRS=media pdfdocs
Signed-off-by: Markus Heiser <markus.heiser@darmarIT.de>
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
This extends the method to build only sub-folders to the targets
"latexdocs" and "pdfdocs". To do so, a conf.py in the sub-folder is
required, where the latex_documents of the sub-folder are
defined. E.g. to build only gpu's PDF add the following to the
Documentation/gpu/conf.py::
+latex_documents = [
+ ("index", "gpu.tex", "Linux GPU Driver Developer's Guide",
+ "The kernel development community", "manual"),
+]
and run:
make SPHINXDIRS=gpu pdfdocs
Signed-off-by: Markus Heiser <markus.heiser@darmarIT.de>
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
The setup() function of a Sphinx-extension can return a dictionary. This
is treated by Sphinx as metadata of the extension [1].
With metadata "parallel_read_safe = True" a extension is marked as
save for "parallel reading of source". This is needed if you want
build in parallel with N processes. E.g.:
make SPHINXOPTS=-j4 htmldocs
will no longer log warnings like:
WARNING: the foobar extension does not declare if it is safe for
parallel reading, assuming it isn't - please ask the extension author
to check and make it explicit.
Add metadata to extensions:
* kernel-doc
* flat-table
* kernel-include
[1] http://www.sphinx-doc.org/en/stable/extdev/#extension-metadata
Signed-off-by: Markus Heiser <markus.heiser@darmarIT.de>
Tested-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
When using a typedef function like this one:
typedef bool v4l2_check_dv_timings_fnc (const struct v4l2_dv_timings * t, void * handle);
The Sphinx C domain expects it to create a c:type: reference,
as that's the way it creates the type references when parsing
a c:function:: declaration.
So, a declaration like:
.. c:function:: bool v4l2_valid_dv_timings (const struct v4l2_dv_timings * t, const struct v4l2_dv_timings_cap * cap, v4l2_check_dv_timings_fnc fnc, void * fnc_handle)
Will create a cross reference for :c:type:`v4l2_check_dv_timings_fnc`.
So, when outputting such typedefs in RST format, we need to handle
this special case, as otherwise it will produce those warnings:
./include/media/v4l2-dv-timings.h:43: WARNING: c:type reference target not found: v4l2_check_dv_timings_fnc
./include/media/v4l2-dv-timings.h:60: WARNING: c:type reference target not found: v4l2_check_dv_timings_fnc
./include/media/v4l2-dv-timings.h:81: WARNING: c:type reference target not found: v4l2_check_dv_timings_fnc
So, change the kernel-doc script to produce a RST output for the
above typedef as:
.. c:type:: v4l2_check_dv_timings_fnc
**Typedef**: timings check callback
**Syntax**
``bool v4l2_check_dv_timings_fnc (const struct v4l2_dv_timings * t, void * handle);``
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
From the old description people still can't get what's the exact
difference between nr_cpus and maxcpus. Especially in kdump kernel
nr_cpus is always suggested if it's implemented in the ARCH. The
reason is nr_cpus is used to limit the max number of possible cpu
in system, the sum of already plugged cpus and hot plug cpus can't
exceed its value. However maxcpus is used to limit how many cpus
are allowed to be brought up during bootup.
Signed-off-by: Baoquan He <bhe@redhat.com>
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
v4l2_err() can not be used for printing error for missing interleaved
support in DMA as this point the pcdev->v4l2_dev is not valid.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Fix this sparse warning:
drivers/media/rc/redrat3.c:490:18: warning: incorrect type in assignment (different base types)
drivers/media/rc/redrat3.c:495:9: warning: cast to restricted __be32
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
changed 'unsigned' to 'unsigned int' to obtain the coding style.
Signed-off-by: Jannik Becher <Becher.Jannik@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Right now, for a struct, kernel-doc produces the following output:
.. c:type:: struct v4l2_prio_state
stores the priority states
**Definition**
::
struct v4l2_prio_state {
atomic_t prios[4];
};
**Members**
``atomic_t prios[4]``
array with elements to store the array priorities
Putting a member name in verbatim and adding a continuation line
causes the LaTeX output to generate something like:
item[atomic_t prios\[4\]] array with elements to store the array priorities
Everything inside "item" is non-breakable, with may produce
lines bigger than the column width.
Also, for function members, like:
int (* rx_read) (struct v4l2_subdev *sd, u8 *buf, size_t count,ssize_t *num);
It puts the name of the member at the end, like:
int (*) (struct v4l2_subdev *sd, u8 *buf, size_t count,ssize_t *num) read
With is very confusing.
The best is to highlight what really matters: the member name.
is a secondary information.
So, change kernel-doc, for it to produce the output on a different way:
**Members**
``prios[4]``
array with elements to store the array priorities
Also, as the type is not part of LaTeX "item[]", LaTeX will split it into
multiple lines, if needed.
So, both LaTeX/PDF and HTML outputs will look good.
It should be noticed, however, that the way Sphinx LaTeX output handles
things like:
Foo
bar
is different than the HTML output. On HTML, it will produce something
like:
**Foo**
bar
While, on LaTeX, it puts both foo and bar at the same line, like:
**Foo** bar
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
* Reuse existing functionality from memdup_user() instead of keeping
duplicate source code.
This issue was detected by using the Coccinelle software.
* Return directly if this copy operation failed.
* Replace the specification of data structures by pointer dereferences
to make the corresponding size determination a bit safer according to
the Linux coding style convention.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The kernel-doc has the wrong function name and also the pindex
parameter is missing in the documentation.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Fix copy-and-paste error: the radio devices are /dev/radio, not /dev/vbi.
Signed-off-by: Hans Verkuil <<hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The error return path of failed calls to heleno_x_pon leak
memory because priv is not kfree'd. Fix this by kfree'ing
priv before returning.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: Abylay Ospan <aospan@netup.ru>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
kmalloc will print enough information in case of failure.
Signed-off-by: Wolfram Sang <wsa-dev@sang-engineering.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
kmalloc will print enough information in case of failure.
Signed-off-by: Wolfram Sang <wsa-dev@sang-engineering.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The v4l2_subdev_core_ops .registered_async callback was added to notify
a subdev when its entity has been registered with the media device, to
allow for example to modify the media graph (i.e: adding entities/links).
But that's not needed since there is already a .registered callback in
struct v4l2_subdev_internal_ops that's called after the entity has been
registered with the media device in v4l2_device_register_subdev().
Suggested-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The driver is using the struct v4l2_subdev_core_ops .registered_async
callback to register the connector entities and create the pad links
after the subdev entity has been registered with the media device.
But the .registered_async callback isn't needed since the v4l2 core
already calls the struct v4l2_subdev_internal_ops .registered callback
in v4l2_device_register_subdev(), after media_device_register_entity().
So, use the .registered() callback instead of the .registered_async()
that is going to be removed in a following patch since isn't needed.
Suggested-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Albeit not prohibited explicitly, re-registering sub-devices generated a
big, loud warning which quite likely soon was followed by a crash. What
followed was re-initialising a media entity, driver's registered() callback
being called and re-adding a list entry to a list.
Prevent this by returning an error if a sub-device is already registered.
[mchehab@s-opensource.com: reorder logic to check if !sd before dereferencing it]
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The macro gobj_to_pad() is defined twice in media-entity.h.
Let's remove one.
Signed-off-by: Liu Ying <gnuiyl@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The function media_entity_enum_empty() returns true when the bitmap
of the input parameter media entity enumeration is empty instead of marked.
This patch corrects the return value description of the function.
Signed-off-by: Liu Ying <gnuiyl@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The macro gobj_to_link() is defined twice in media-entity.h.
Let's remove one.
Signed-off-by: Liu Ying <gnuiyl@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
It is likely that checking the result of the 2nd 'read16' is expected here.
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Add support for the Hauppauge WinTV quadHD ATSC version.
IR support has not been provided, all 4 tuners, demodulators etc are working.
Further documentation can be found on Linux TV wiki.
Signed-off-by: Stephen Backway <stev391@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
When resuming from suspend-to-RAM on r8a7795/salvator-x:
dpm_run_callback(): pm_genpd_resume_noirq+0x0/0x90 returns 1
PM: Device fe940000.fdp1 failed to resume noirq: error 1
dpm_run_callback(): pm_genpd_resume_noirq+0x0/0x90 returns 1
PM: Device fe944000.fdp1 failed to resume noirq: error 1
dpm_run_callback(): pm_genpd_resume_noirq+0x0/0x90 returns 1
PM: Device fe948000.fdp1 failed to resume noirq: error 1
According to its documentation, rcar_fcp_enable() returns 0 on success
or a negative error code if an error occurs. Hence
fdp1_pm_runtime_resume() and vsp1_pm_runtime_resume() forward its return
value to their callers.
However, rcar_fcp_enable() forwards the return value of
pm_runtime_get_sync(), which can actually be 1 on success, leading to
the resume failure above.
To fix this, consider only negative values returned by
pm_runtime_get_sync() to be failures.
Fixes: 7b49235e83 ("[media] v4l: Add Renesas R-Car FCP driver")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The core will do this for us now.
Signed-off-by: Wolfram Sang <wsa-dev@sang-engineering.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The core will do this for us now.
Signed-off-by: Wolfram Sang <wsa-dev@sang-engineering.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The core will do this for us now.
Signed-off-by: Wolfram Sang <wsa-dev@sang-engineering.com>
Acked-by: Abylay Ospan <aospan@netup.ru>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Fix to return error code -ENOMEM from the i2c client register error
handling case instead of 0, as done elsewhere in this function.
Signed-off-by: Wei Yongjun <weiyj.lk@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The core will do this for us now.
Signed-off-by: Wolfram Sang <wsa-dev@sang-engineering.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
alloc_workqueue replaces deprecated create_singlethread_workqueue().
The MFC device driver is a v4l2 driver which can encode/decode video
raw/elementary streams and has support for all popular video codecs.
The driver's watchdog_workqueue has been replaced with system_wq since
it queues a single work item, &dev->watchdog_work, which calls for no
ordering requirement. The work item is involved in running the watchdog
timer and is not being used on a memory reclaim path.
Work item has been flushed in s5p_mfc_remove() to ensure
that there are no pending tasks while disconnecting the driver.
Signed-off-by: Bhaktipriya Shridhar <bhaktipriya96@gmail.com>
Acked-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Missing blank lines after declarations are making it hard to read the
code. Fix them and also fix other checkpatch warnings at the same time.
Signed-off-by: Shuah Khan <shuahkh@osg.samsung.com>
Acked-by: Jacek Anaszewski <j.anaszewski@samsung.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Remove unneeded error handling on the result of a call
to platform_get_resource() when the value is passed to
devm_ioremap_resource().
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
According to the V4L2 documentation the driver and card fields should be
used to identify the driver and the device but the gsc-m2m driver fills
those field using the platform device name, which in turn is the name of
the device DT node.
So not only the filled information isn't correct but also the same values
are used in the driver, card and bus_info fields.
Before this patch:
Driver Info (not using libv4l2):
Driver name : 13e00000.video-
Card type : 13e00000.video-scaler
Bus info : platform:13e00000.video-scaler
Driver version: 4.7.0
After this patch:
Driver Info (not using libv4l2):
Driver name : exynos-gsc
Card type : exynos-gsc gscaler
Bus info : platform:13e00000.video-scaler
Driver version: 4.7.0
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The driver doesn't set the device in the struct v4l2_capability bus_info
field so v4l2-compliance reports the following error for VIDIOC_QUERYCAP:
Required ioctls:
fail: v4l2-compliance.cpp(537): missing bus_info prefix ('platform')
test VIDIOC_QUERYCAP: FAIL
This patch fixes this by filling also the device besides the bus.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Mauro Carvalho Chehab