Commit Graph

82 Commits

Author SHA1 Message Date
Michael Buesch e92aa634a3 b44: Disable device on shutdown
Disable the SSB core on device shutdown.
This has two advantages:
1) A clean device shutdown is always desired here, because we disable
  the device's global crystal in the next statement.
2) This fixes a bug where the device will come up with the enable-bit
  set on the next initialization (without a reboot inbetween).
  This causes breakage on the second initialization due to code that
  checks this bit (ssb_device_is_enabled() checks).

Reported-by: Pantelis Koukousoulas <pktoss@gmail.com>
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-02-26 22:35:02 -08:00
Michael Buesch f8af11af85 b44: Unconditionally enable interrupt routing on reset
Unconditionally setup the IRQ routing on chip reset.
It's safe to call ssb_pcicore_dev_irqvecs_enable() unconditionally, because
it has internal checks for redundant calls.

This fixes problems where hardware will not come up properly
due to quirks in the enable-bit hardware.

Reported-by: Pantelis Koukousoulas <pktoss@gmail.com>
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-02-26 22:33:00 -08:00
Eric Dumazet a58c891a53 b44: GFP_DMA skb should not escape from driver
b44 chip has some hardware limitations, that need GFP_DMA bounce
buffers in some situations.

In order to not deplete DMA zone, we should keep allocated GFP_DMA skb
only for driver use. At rx time, we copy such skb to newly allocated
skb, reusing existing copybreak infrastructure.

On machines with low amount of memory, all skb meet the hardware limitation,
so no copy is needed. We detect this situation using a new device flag, set
to one if one GFP_DMA skb was ever allocated by b44_alloc_rx_skb().

Previously allocated skb, even outside from DMA zone will then be recycled,
to have minimal impact on DMA zone use.

Signed-off-by: Eric Dumazet <dada1@cosmosbay.com>
Tested-by: Ionut Leonte <ionut.leonte@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-01-15 15:29:35 -08:00
Felix Fietkau 4ca857958c b44: fix misalignment and wasted space in rx handling
Broadcom 4400 puts a header of configurable size (apparently needs
to be at least 28 bytes) in front of received packets. When handling
this, the previous code accidentally added the offset 30 *twice* for
the software and once for the hardware, thereby cancelling out the
IP alignment effect of the 30 byte padding and wasting an additional
30 bytes of memory per packet.

This patch fixes this problem and improves routing throughput by
about 30% on MIPS, where unaligned access is expensive.

Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-01-11 00:04:12 -08:00
Stephen Hemminger 403413e50d b44: convert to net_device_ops
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-01-07 18:10:49 -08:00
David S. Miller 2d5451d261 net: Fix warning fallout from recent NAPI interface changes.
When we removed the network device argument from several
NAPI interfaces in 908a7a16b8
("net: Remove unused netdev arg from some NAPI interfaces.")
several drivers now started getting unused variable warnings.

This fixes those up.

Signed-off-by: David S. Miller <davem@davemloft.net>
2008-12-26 15:10:00 -08:00
Neil Horman 908a7a16b8 net: Remove unused netdev arg from some NAPI interfaces.
When the napi api was changed to separate its 1:1 binding to the net_device
struct, the netif_rx_[prep|schedule|complete] api failed to remove the now
vestigual net_device structure parameter.  This patch cleans up that api by
properly removing it..

Signed-off-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2008-12-22 20:43:12 -08:00
David S. Miller babcda74e9 drivers/net: Kill now superfluous ->last_rx stores.
The generic packet receive code takes care of setting
netdev->last_rx when necessary, for the sake of the
bonding ARP monitor.

Drivers need not do it any more.

Some cases had to be skipped over because the drivers
were making use of the ->last_rx value themselves.

Signed-off-by: David S. Miller <davem@davemloft.net>
2008-11-03 21:11:17 -08:00
Johannes Berg e174961ca1 net: convert print_mac to %pM
This converts pretty much everything to print_mac. There were
a few things that had conflicts which I have just dropped for
now, no harm done.

I've built an allyesconfig with this and looked at the files
that weren't built very carefully, but it's a huge patch.

Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
2008-10-27 17:06:18 -07:00
Michael Buesch f225763a7d ssb, b43, b43legacy, b44: Rewrite SSB DMA API
This is a rewrite of the DMA API for SSB devices.
This is needed, because the old (non-existing) "API" made too many bad
assumptions on the API of the host-bus (PCI).
This introduces an almost complete SSB-DMA-API that maps to the lowlevel
bus-API based on the bustype.

Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2008-06-27 09:09:15 -04:00
Michael Buesch 4ac58469f1 ssb: Fix usage of struct device used for DMAing
This fixes DMA on architectures where DMA is nontrivial, like PPC64.
We must use the host-device's (PCI) struct device for any DMA
operation instead of the SSB device. For this we add a new
struct device pointer to the SSB device structure that will always
point to the right device for DMAing.

Without this patch b43 and b44 drivers won't work on complex-DMA
architectures, that for example need dev->archdata for DMA operations.

Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2008-04-15 15:04:35 -04:00
Michael Buesch 5ea79631c0 b44: Truncate PHY address
Some ROMs on embedded devices store incorrect values for
the PHY address of the ethernet device.
It looks like the number is sign-extended.
Truncate the value by applying the PHY-address mask to it.
The patch was tested on a bcm47xx embedded system (where the bug
triggers) and a bcm4400 PCI card.

Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2008-03-25 23:42:07 -04:00
Miguel Botón fedb0eefe2 b44: power down PHY when interface down
This is just this patch (http://lkml.org/lkml/2007/7/1/51) but adapted
to the 'b44' ssb driver.

Signed-off-by: Miguel Botón <mboton@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2008-01-28 15:09:19 -08:00
Larry Finger 458414b2e3 b44: Convert to use of the new SPROM structure
The b44 driver is changed to use the new SPROM data structure.

Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2008-01-28 15:04:42 -08:00
Jeff Garzik b9f2c0440d [netdrvr] Stop using legacy hooks ->self_test_count, ->get_stats_count
These have been superceded by the new ->get_sset_count() hook.

Signed-off-by: Jeff Garzik <jeff@garzik.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
2007-10-10 16:51:45 -07:00
Michael Buesch 753f492093 [B44]: port to native ssb support
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2007-10-10 16:51:43 -07:00
Joe Perches 0795af5729 [NET]: Introduce and use print_mac() and DECLARE_MAC_BUF()
This is nicer than the MAC_FMT stuff.

Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2007-10-10 16:51:42 -07:00
Ralf Baechle 10d024c1b2 [NET]: Nuke SET_MODULE_OWNER macro.
It's been a useless no-op for long enough in 2.6 so I figured it's time to
remove it.  The number of people that could object because they're
maintaining unified 2.4 and 2.6 drivers is probably rather small.

[ Handled drivers added by netdev tree and some missed IRDA cases... -DaveM ]

Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
2007-10-10 16:51:13 -07:00
Stephen Hemminger bea3348eef [NET]: Make NAPI polling independent of struct net_device objects.
Several devices have multiple independant RX queues per net
device, and some have a single interrupt doorbell for several
queues.

In either case, it's easier to support layouts like that if the
structure representing the poll is independant from the net
device itself.

The signature of the ->poll() call back goes from:

	int foo_poll(struct net_device *dev, int *budget)

to

	int foo_poll(struct napi_struct *napi, int budget)

The caller is returned the number of RX packets processed (or
the number of "NAPI credits" consumed if you want to get
abstract).  The callee no longer messes around bumping
dev->quota, *budget, etc. because that is all handled in the
caller upon return.

The napi_struct is to be embedded in the device driver private data
structures.

Furthermore, it is the driver's responsibility to disable all NAPI
instances in it's ->stop() device close handler.  Since the
napi_struct is privatized into the driver's private data structures,
only the driver knows how to get at all of the napi_struct instances
it may have per-device.

With lots of help and suggestions from Rusty Russell, Roland Dreier,
Michael Chan, Jeff Garzik, and Jamal Hadi Salim.

Bug fixes from Thomas Graf, Roland Dreier, Peter Zijlstra,
Joseph Fannin, Scott Wood, Hans J. Koch, and Michael Chan.

[ Ported to current tree and all drivers converted.  Integrated
  Stephen's follow-on kerneldoc additions, and restored poll_list
  handling to the old style to fix mutual exclusion issues.  -DaveM ]

Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
2007-10-10 16:47:45 -07:00
Matthew Wilcox 313674afa8 [NET]: ethtool_perm_addr only has one implementation
All drivers implement ethtool get_perm_addr the same way -- by calling
the generic function.  So we can inline the generic function into the
caller and avoid going through the drivers.

Signed-off-by: Matthew Wilcox <matthew@wil.cx>
Signed-off-by: David S. Miller <davem@davemloft.net>
2007-07-31 14:00:29 -07:00
Yoann Padioleau dd00cc486a some kmalloc/memset ->kzalloc (tree wide)
Transform some calls to kmalloc/memset to a single kzalloc (or kcalloc).

Here is a short excerpt of the semantic patch performing
this transformation:

@@
type T2;
expression x;
identifier f,fld;
expression E;
expression E1,E2;
expression e1,e2,e3,y;
statement S;
@@

 x =
- kmalloc
+ kzalloc
  (E1,E2)
  ...  when != \(x->fld=E;\|y=f(...,x,...);\|f(...,x,...);\|x=E;\|while(...) S\|for(e1;e2;e3) S\)
- memset((T2)x,0,E1);

@@
expression E1,E2,E3;
@@

- kzalloc(E1 * E2,E3)
+ kcalloc(E1,E2,E3)

[akpm@linux-foundation.org: get kcalloc args the right way around]
Signed-off-by: Yoann Padioleau <padator@wanadoo.fr>
Cc: Richard Henderson <rth@twiddle.net>
Cc: Ivan Kokshaysky <ink@jurassic.park.msu.ru>
Acked-by: Russell King <rmk@arm.linux.org.uk>
Cc: Bryan Wu <bryan.wu@analog.com>
Acked-by: Jiri Slaby <jirislaby@gmail.com>
Cc: Dave Airlie <airlied@linux.ie>
Acked-by: Roland Dreier <rolandd@cisco.com>
Cc: Jiri Kosina <jkosina@suse.cz>
Acked-by: Dmitry Torokhov <dtor@mail.ru>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Acked-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Acked-by: Pierre Ossman <drzeus-list@drzeus.cx>
Cc: Jeff Garzik <jeff@garzik.org>
Cc: "David S. Miller" <davem@davemloft.net>
Acked-by: Greg KH <greg@kroah.com>
Cc: James Bottomley <James.Bottomley@steeleye.com>
Cc: "Antonino A. Daplas" <adaplas@pol.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2007-07-19 10:04:50 -07:00
Stephen Hemminger bf0dcbd929 b44: use netdev_alloc_skb
Use netdev_alloc_skb rather than dev_alloc_skb when allocating
receive buffers.

Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2007-07-08 22:16:40 -04:00
Stephen Hemminger 72f4861ef9 b44: packet offset is constant
The receive buffer offset is constant in this driver.

Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2007-07-08 22:16:40 -04:00
Stephen Hemminger f65a71775c b44: tx bounce sizing.
No need to grap full size MTU buffer for possibly small transmit
bounce buffers.

Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2007-07-08 22:16:40 -04:00
Stephen Hemminger a72a817973 b44: timer power saving
Make the PHY and statistic timer run on one second boundary
for powersaving.

On resume, the driver should check for link up immediately, to
get online faster (rather than waiting for the next second).

Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2007-07-08 22:16:39 -04:00
Arnaldo Carvalho de Melo d626f62b11 [SK_BUFF]: Introduce skb_copy_from_linear_data{_offset}
To clearly state the intent of copying from linear sk_buffs, _offset being a
overly long variant but interesting for the sake of saving some bytes.

Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
2007-04-25 22:28:23 -07:00
Arnaldo Carvalho de Melo 4c13eb6657 [ETH]: Make eth_type_trans set skb->dev like the other *_type_trans
One less thing for drivers writers to worry about.

Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2007-04-25 22:24:30 -07:00
Bill Helfinstine cda22aa94d b44: fix IFF_ALLMULTI handling of CAM slots
If you set the IFF_ALLMULTI flag on a b44 device, or if you join more than
B44_MCAST_TABLE_SIZE multicast groups, the device will stop receiving unicast
messages.  This is because the __b44_set_mac_addr call sets the zeroth CAM
entry to the MAC address of the device, and then the loop at line 1722
proceeds to overwrite it unless the value of i is set by the __b44_load_mcast
call.  However, when IFF_ALLMULTI is set, that call is bypassed, leaving i set
to zero.

Fixed by starting the loop at 1 to make it skip the CAM entry for the MAC
address.

Signed-off-by: Bill Helfinstine <bhelf@flitterfly.whirpon.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2007-04-03 22:31:09 -04:00
Gary Zambrano 40ee8c768c B44: increase wait loop
The b44 Enet control disable bit may take longer to clear on some
systems, so the loop count is increased with this patch. Functionality
is not compromised, but a debug message can be seen when the bit is not
cleared within the count value.
Thanks to Vasileios Lourdas who reported the problem.

Signed-off by: Gary Zambrano <zambrano@broadcom.com>

Signed-off-by: Jeff Garzik <jeff@garzik.org>
2007-02-17 15:37:14 -05:00
Gary Zambrano 97db9ee7ee b44: replace define
Replaced B44_DMA_MASK with DMA_30BIT_MASK.

Signed-off by: Gary Zambrano <zambrano@broadcom.com>

Signed-off-by: Jeff Garzik <jeff@garzik.org>
2007-02-17 15:37:14 -05:00
Al Viro a7bed27dc6 b44 endian annotations
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2007-02-06 19:03:56 -05:00
Dmitriy Monakhov 90afd0e574 Broadcom 4400 resume small fix
Some issues in b44_resume().

- Return value of pci_enable_device() was ignored.

- If request_irq() has failed we have to just disable device and exit.

Signed-off-by: Dmitriy Monakhov <dmonakhov@openvz.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2007-01-30 09:36:02 -05:00
Al Viro 00576e9380 b44: src_desc->addr is little-endian
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2007-01-30 09:36:02 -05:00
Michael Chan 5fc7d61aee b44: Fix frequent link changes
This fixes the issue of frequent link changes under heavy traffic reported
below:

http://bugzilla.kernel.org/show_bug.cgi?id=7696
https://bugzilla.redhat.com/bugzilla/show_bug.cgi?id=216338

The b44 chip occasionally needs to be reset when ISTAT_ERRORS are
encountered.  The reset sequence includes a PHY reset that will take many
seconds to complete and cause the link to go down and up.  By skipping the
PHY reset, it will greatly reduce the interruption when ISTAT_ERRORS are
encountered.

Change the full_reset parameter to reset_kind parameter in b44_init_hw().
This will allow PHY reset to be skipped when ISTAT_ERRORS are encountered.

Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2007-01-30 09:36:01 -05:00
Francois Romieu d15e9c4d9a netpoll: drivers must not enable IRQ unconditionally in their NAPI handler
net/core/netpoll.c::netpoll_send_skb() calls the poll handler when
it is available. As netconsole can be used from almost any context,
IRQ must not be enabled blindly in the NAPI handler of a driver which
supports netpoll.

b57bd06655 fixed the issue for the
8139too.c driver.

Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2006-12-26 16:24:11 -05:00
Johannes Berg e78181feb0 [PATCH] b44: change comment about irq mask register
Through some experimentation with the similarly built bcm43xx I came to
the conclusion that if the hw/firmware sets a bit in the interrupt
register, an interrupt will only be raised if that bit is included in
the interrupt mask. Hence, the interrupt mask is more like an interrupt
control mask.

This patch changes the comment to reflect that.

Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2006-11-07 04:27:51 -05:00
Michael Buesch 6f62768344 [PATCH] b44: fix eeprom endianess issue
This fixes eeprom read on big-endian architectures.

readw returns the data in CPU order.  With cpu_to_le16 we convert it to little
endian, because "ptr" is a pointer to a _byte_ arrray.  See the cast above.  A
byte array is little endian.

The bug is:

Reading u16 values with readw, casting them into an u8 array and accessing
this u8 array as an u8 (byte) array.  The correct fix is to swap the
CPU-ordering value returned by readw into little endian, as the u8 array is
little endian.

This compiles to nothing on little endian hardware (so it does not change b44
code on LE hardware), but _fixes_ code on BE hardware.

Signed-off-by: Michael Buesch <mb@bu3sch.de>
Cc: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2006-10-11 03:56:33 -04:00
Jeff Garzik 24fcbacedb Merge branch 'master' into upstream-fixes 2006-10-11 03:56:12 -04:00
David Howells 7d12e780e0 IRQ: Maintain regs pointer globally rather than passing to IRQ handlers
Maintain a per-CPU global "struct pt_regs *" variable which can be used instead
of passing regs around manually through all ~1800 interrupt handlers in the
Linux kernel.

The regs pointer is used in few places, but it potentially costs both stack
space and code to pass it around.  On the FRV arch, removing the regs parameter
from all the genirq function results in a 20% speed up of the IRQ exit path
(ie: from leaving timer_interrupt() to leaving do_IRQ()).

Where appropriate, an arch may override the generic storage facility and do
something different with the variable.  On FRV, for instance, the address is
maintained in GR28 at all times inside the kernel as part of general exception
handling.

Having looked over the code, it appears that the parameter may be handed down
through up to twenty or so layers of functions.  Consider a USB character
device attached to a USB hub, attached to a USB controller that posts its
interrupts through a cascaded auxiliary interrupt controller.  A character
device driver may want to pass regs to the sysrq handler through the input
layer which adds another few layers of parameter passing.

I've build this code with allyesconfig for x86_64 and i386.  I've runtested the
main part of the code on FRV and i386, though I can't test most of the drivers.
I've also done partial conversion for powerpc and MIPS - these at least compile
with minimal configurations.

This will affect all archs.  Mostly the changes should be relatively easy.
Take do_IRQ(), store the regs pointer at the beginning, saving the old one:

	struct pt_regs *old_regs = set_irq_regs(regs);

And put the old one back at the end:

	set_irq_regs(old_regs);

Don't pass regs through to generic_handle_irq() or __do_IRQ().

In timer_interrupt(), this sort of change will be necessary:

	-	update_process_times(user_mode(regs));
	-	profile_tick(CPU_PROFILING, regs);
	+	update_process_times(user_mode(get_irq_regs()));
	+	profile_tick(CPU_PROFILING);

I'd like to move update_process_times()'s use of get_irq_regs() into itself,
except that i386, alone of the archs, uses something other than user_mode().

Some notes on the interrupt handling in the drivers:

 (*) input_dev() is now gone entirely.  The regs pointer is no longer stored in
     the input_dev struct.

 (*) finish_unlinks() in drivers/usb/host/ohci-q.c needs checking.  It does
     something different depending on whether it's been supplied with a regs
     pointer or not.

 (*) Various IRQ handler function pointers have been moved to type
     irq_handler_t.

Signed-Off-By: David Howells <dhowells@redhat.com>
(cherry picked from 1b16e7ac850969f38b375e511e3fa2f474a33867 commit)
2006-10-05 15:10:12 +01:00
Jeff Garzik 2f614fe04f [netdrvr] b44: handle excessive multicast groups
If there are more than B44_MCAST_TABLE_SIZE groups in the dev->mc_list,
it will only listen to the first B44_MCAST_TABLE_SIZE that it sees.

This change makes the driver go into RXCONFIG_ALLMULTI mode if there
are more than B44_MCAST_TABLE_SIZE groups being subscribed to, similar
to other network drivers.

Noticed by Bill Helfinstine <bhelf@flitterfly.whirpon.com>

Signed-off-by: Jeff Garzik <jeff@garzik.org>
2006-10-05 07:10:38 -04:00
Jeff Garzik 7282d491ec drivers/net: const-ify ethtool_ops declarations
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2006-09-13 14:30:00 -04:00
Jeff Garzik 299176206b drivers/net: Remove deprecated use of pci_module_init()
From: Michal Piotrowski <michal.k.k.piotrowski@gmail.com>

Signed-off-by: Michal Piotrowski <michal.k.k.piotrowski@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2006-08-19 17:48:59 -04:00
Jeff Garzik 9b91cf9daa [netdrvr] use dev_xxx() printk helpers, rather than dev_printk(KERN_xxx, ...
Suggested by Jiri Slaby.

Signed-off-by: Jeff Garzik <jeff@garzik.org>
2006-07-05 13:42:57 -04:00
Jeff Garzik 2e8a538d86 [netdrvr] Use dev_printk() when ethernet interface isn't available
For messages prior to register_netdev(), prefer dev_printk() because
that prints out both our driver name and our [PCI | whatever] bus id.

Updates: 8139{cp,too}, b44, bnx2, cassini, {eepro,epic}100, fealnx,
	 hamachi, ne2k-pci, ns83820, pci-skeleton, r8169.

Signed-off-by: Jeff Garzik <jeff@garzik.org>
2006-07-05 13:42:07 -04:00
Thomas Gleixner 1fb9df5d30 [PATCH] irq-flags: drivers/net: Use the new IRQF_ constants
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2006-07-02 13:58:51 -07:00
Gary Zambrano 4d1dabdb52 [PATCH] b44: update version to 1.01
Update the driver version to 1.01

Signed-off-by: Gary Zambrano <zambrano@broadcom.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2006-06-22 23:16:13 -04:00
Gary Zambrano 725ad800b7 [PATCH] b44: add wol for old nic
This patch adds wol support for the older 440x nics that use pattern matching.
This patch is a redo thanks to feedback from Michael Chan and Francois Romieu.

Signed-off-by: Gary Zambrano  <zambrano@broadcom.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2006-06-22 23:16:13 -04:00
Gary Zambrano 00e8b3aa1c [PATCH] b44: add parameter
This patch adds a parameter to init_hw() to not completely initialize
the nic for wol.

Signed-off-by: Gary Zambrano <zambrano@broadcom.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2006-06-22 23:16:13 -04:00
Gary Zambrano 52cafd9655 [PATCH] b44: add wol
Adds wol to the driver.
This is a redo of a previous patch thanks to feedback from Francois Romieu.

Signed-off-by Gary Zambrano <zambrano@broadcom.com>

Signed-off-by: Jeff Garzik <jeff@garzik.org>
2006-06-22 23:16:13 -04:00
Gary Zambrano 47b9c3b1e6 [PATCH] b44: fix manual speed/duplex/autoneg settings
Fixes for speed/duplex/autoneg settings and driver settings info.
This is a redo of a previous patch thanks to feedback from Jeff Garzik.

Signed-off-by: Gary Zambrano <zambrano@broadcom.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2006-06-22 23:16:13 -04:00