The brcmfmac driver ignores any errors on initialization with the
different busses by deferring the initialization to a workqueue and
ignoring all possible errors that might happen. Fix up all of this by
only allowing the module to load if all bus registering worked properly.
Cc: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210503115736.2104747-70-gregkh@linuxfoundation.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This reverts commit 42daad3343.
Because of recent interactions with developers from @umn.edu, all
commits from them have been recently re-reviewed to ensure if they were
correct or not.
Upon review, this commit was found to be incorrect for the reasons
below, so it must be reverted. It will be fixed up "correctly" in a
later kernel change.
The original commit here did nothing to actually help if usb_register()
failed, so it gives a "false sense of security" when there is none. The
correct solution is to correctly unwind from this error.
Cc: Kangjie Lu <kjlu@umn.edu>
Cc: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210503115736.2104747-69-gregkh@linuxfoundation.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The libertas driver was trying to register sysfs groups "by hand" which
causes them to be created _after_ the device is initialized and
announced to userspace, which causes races and can prevent userspace
tools from seeing the sysfs files correctly.
Fix this up by using the built-in sysfs_groups pointers in struct
net_device which were created for this very reason, fixing the race
condition, and properly allowing for any error that might have occured
to be handled properly.
Cc: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210503115736.2104747-54-gregkh@linuxfoundation.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This reverts commit 434256833d.
Because of recent interactions with developers from @umn.edu, all
commits from them have been recently re-reviewed to ensure if they were
correct or not.
Upon review, this commit was found to be incorrect for the reasons
below, so it must be reverted. It will be fixed up "correctly" in a
later kernel change.
The original commit was incorrect, the error needs to be propagated back
to the caller AND if the second group call fails, the first needs to be
removed. There are much better ways to solve this, the driver should
NOT be calling sysfs_create_group() on its own as it is racing userspace
and loosing.
Cc: Kangjie Lu <kjlu@umn.edu>
Cc: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210503115736.2104747-53-gregkh@linuxfoundation.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Propagate error code from failure of ath6kl_wmi_cmd_send() to the
caller.
Signed-off-by: Anirudh Rayabharam <mail@anirudhrb.com>
Cc: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210503115736.2104747-44-gregkh@linuxfoundation.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This reverts commit fc6a652155.
Because of recent interactions with developers from @umn.edu, all
commits from them have been recently re-reviewed to ensure if they were
correct or not.
Upon review, this commit was found to be incorrect for the reasons
below, so it must be reverted. It will be fixed up "correctly" in a
later kernel change.
The change being reverted does NOTHING as the caller to this function
does not even look at the return value of the call. So the "claim" that
this fixed an an issue is not true. It will be fixed up properly in a
future patch by propagating the error up the stack correctly.
Cc: Kangjie Lu <kjlu@umn.edu>
Cc: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210503115736.2104747-43-gregkh@linuxfoundation.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If alloc_workqueue() fails, properly catch this and propagate the error
to the calling functions, so that the devuce initialization will
properly error out.
Cc: Kalle Valo <kvalo@codeaurora.org>
Cc: Bryan Brattlof <hello@bryanbrattlof.com>
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20210503115736.2104747-14-gregkh@linuxfoundation.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This reverts commit 765976285a.
Because of recent interactions with developers from @umn.edu, all
commits from them have been recently re-reviewed to ensure if they were
correct or not.
Upon review, this commit was found to be incorrect for the reasons
below, so it must be reverted. It will be fixed up "correctly" in a
later kernel change.
This commit is not correct, it should not have used unlikely() and is
not propagating the error properly to the calling function, so it should
be reverted at this point in time. Also, if the check failed, the
work queue was still assumed to be allocated, so further accesses would
have continued to fail, meaning this patch does nothing to solve the
root issues at all.
Cc: Kangjie Lu <kjlu@umn.edu>
Cc: Kalle Valo <kvalo@codeaurora.org>
Cc: Bryan Brattlof <hello@bryanbrattlof.com>
Fixes: 765976285a ("rtlwifi: fix a potential NULL pointer dereference")
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20210503115736.2104747-13-gregkh@linuxfoundation.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The section "19) Editor modelines and other cruft" in
Documentation/process/coding-style.rst clearly says, "Do not include any
of these in source files."
I recently receive a patch to explicitly add a new one.
Let's do treewide cleanups, otherwise some people follow the existing code
and attempt to upstream their favoriate editor setups.
It is even nicer if scripts/checkpatch.pl can check it.
If we like to impose coding style in an editor-independent manner, I think
editorconfig (patch [1]) is a saner solution.
[1] https://lore.kernel.org/lkml/20200703073143.423557-1-danny@kdrag0n.dev/
Link: https://lkml.kernel.org/r/20210324054457.1477489-1-masahiroy@kernel.org
Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>
Acked-by: Geert Uytterhoeven <geert@linux-m68k.org>
Reviewed-by: Miguel Ojeda <ojeda@kernel.org> [auxdisplay]
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Now that proc_ops are separate from file_operations and other operations
it easy to check all instances to have ->proc_lseek hook and remove check
in main code.
Note:
nonseekable_open() files naturally don't require ->proc_lseek.
Garbage collect pde_lseek() function.
[adobriyan@gmail.com: smoke test lseek()]
Link: https://lkml.kernel.org/r/YG4OIhChOrVTPgdN@localhost.localdomain
Link: https://lkml.kernel.org/r/YFYX0Bzwxlc7aBa/@localhost.localdomain
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
- Fix spellos in comments for the tegra and sun8i (Bhaskar Chowdhury)
- Add the missing fifth node on the rcar_gen3 sensor (Niklas
Söderlund)
- Remove duplicate include in ti-bandgap (Zhang Yunkai)
- Assign error code in the error path in the function
thermal_of_populate_bind_params() (Jia-Ju Bai)
- Fix spelling mistake in a comment 'disabed' -> 'disabled' (Colin Ian
King)
- Use the device name instead of auto-numbering for a better
identification of the cooling device (Daniel Lezcano)
- Improve a bit the division accuracy in the power allocator governor
(Jeson Gao)
- Enable the missing third sensor on msm8976 (Konrad Dybcio)
- Add QCom tsens driver co-maintainer (Thara Gopinath)
- Fix memory leak and use after free errors in the core code (Daniel
Lezcano)
- Add the MDM9607 compatible bindings (Konrad Dybcio)
- Fix trivial spello in the copyright name for Hisilicon (Hao Fang)
- Fix negative index array access when converting the frequency to
power in the energy model (Brian-sy Yang)
- Add support for Gen2 new PMIC support for Qcom SPMI (David Collins)
- Update maintainer file for CPU cooling device section (Lukasz Luba)
- Fix missing put_device on error in the Qcom tsens driver (Guangqing
Zhu)
- Add compatible DT binding for sm8350 (Robert Foss)
- Add support for the MDM9607's tsens driver (Konrad Dybcio)
- Remove duplicate error messages in thermal_mmio and the bcm2835
driver (Ruiqi Gong)
- Add the Thermal Temperature Cooling driver (Zhang Rui)
- Remove duplicate error messages in the Hisilicon sensor driver (Ye
Bin)
- Use the devm_platform_ioremap_resource_byname() function instead of
a couple of corresponding calls (dingsenjie)
- Sort the headers alphabetically in the ti-bandgap driver (Zhen Lei)
- Add missing property in the DT thermal sensor binding (Rafał
Miłecki)
- Remove dead code in the ti-bandgap sensor driver (Lin Ruizhe)
- Convert the BRCM DT bindings to the yaml schema (Rafał Miłecki)
- Replace the thermal_notify_framework() call by a call to the
thermal_zone_device_update() function. Remove the function as well
as the corresponding documentation (Thara Gopinath)
- Add support for the ipq8064-tsens sensor along with a set of
cleanups and code preparation (Ansuel Smith)
- Add a lockless __thermal_cdev_update() function to improve the
locking scheme in the core code and governors (Lukasz Luba)
- Fix multiple cooling device notification changes (Lukasz Luba)
- Remove unneeded variable initialization (Colin Ian King)
-----BEGIN PGP SIGNATURE-----
iQEzBAABCAAdFiEEGn3N4YVz0WNVyHskqDIjiipP6E8FAmCRqDIACgkQqDIjiipP
6E8O2Qf5AQvSVoN9WYRBLo1+a4mkGsJ/wHQMEsOA4FVHft5/QVkRtpMNbSiyq00O
YTpNuoBqiYm/tSTyzK/5Oh+0ucgm/ef4c4dTyPjZYw2GB+3rYNRAXdX/tB6Ggjl/
oUArUCoSQZjOU6Y573B05rcHp1PVM/XL9LgD1uX76tXA1MaGvsyC0cyPRAdOANke
W83BWI0XMhv8B1bZwHVB2Oft5x6HhqWBl3HKbNOmPEMtwkqqBCFAqB0wNEH88ZTf
2hyBjBoZQHdMkJsC0piMvIyAjHZiIjQB47VWz31EvKB3/E28xCqRqPViPq9QbrA5
got0+oDbxI96T024ndXRomc0SSxZnw==
=5THg
-----END PGP SIGNATURE-----
Merge tag 'thermal-v5.13-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/thermal/linux
Pull thermal updates from Daniel Lezcano:
- Remove duplicate error message for the amlogic driver (Tang Bin)
- Fix spellos in comments for the tegra and sun8i (Bhaskar Chowdhury)
- Add the missing fifth node on the rcar_gen3 sensor (Niklas Söderlund)
- Remove duplicate include in ti-bandgap (Zhang Yunkai)
- Assign error code in the error path in the function
thermal_of_populate_bind_params() (Jia-Ju Bai)
- Fix spelling mistake in a comment 'disabed' -> 'disabled' (Colin Ian
King)
- Use the device name instead of auto-numbering for a better
identification of the cooling device (Daniel Lezcano)
- Improve a bit the division accuracy in the power allocator governor
(Jeson Gao)
- Enable the missing third sensor on msm8976 (Konrad Dybcio)
- Add QCom tsens driver co-maintainer (Thara Gopinath)
- Fix memory leak and use after free errors in the core code (Daniel
Lezcano)
- Add the MDM9607 compatible bindings (Konrad Dybcio)
- Fix trivial spello in the copyright name for Hisilicon (Hao Fang)
- Fix negative index array access when converting the frequency to
power in the energy model (Brian-sy Yang)
- Add support for Gen2 new PMIC support for Qcom SPMI (David Collins)
- Update maintainer file for CPU cooling device section (Lukasz Luba)
- Fix missing put_device on error in the Qcom tsens driver (Guangqing
Zhu)
- Add compatible DT binding for sm8350 (Robert Foss)
- Add support for the MDM9607's tsens driver (Konrad Dybcio)
- Remove duplicate error messages in thermal_mmio and the bcm2835
driver (Ruiqi Gong)
- Add the Thermal Temperature Cooling driver (Zhang Rui)
- Remove duplicate error messages in the Hisilicon sensor driver (Ye
Bin)
- Use the devm_platform_ioremap_resource_byname() function instead of a
couple of corresponding calls (dingsenjie)
- Sort the headers alphabetically in the ti-bandgap driver (Zhen Lei)
- Add missing property in the DT thermal sensor binding (Rafał Miłecki)
- Remove dead code in the ti-bandgap sensor driver (Lin Ruizhe)
- Convert the BRCM DT bindings to the yaml schema (Rafał Miłecki)
- Replace the thermal_notify_framework() call by a call to the
thermal_zone_device_update() function. Remove the function as well as
the corresponding documentation (Thara Gopinath)
- Add support for the ipq8064-tsens sensor along with a set of cleanups
and code preparation (Ansuel Smith)
- Add a lockless __thermal_cdev_update() function to improve the
locking scheme in the core code and governors (Lukasz Luba)
- Fix multiple cooling device notification changes (Lukasz Luba)
- Remove unneeded variable initialization (Colin Ian King)
* tag 'thermal-v5.13-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/thermal/linux: (55 commits)
thermal/drivers/mtk_thermal: Remove redundant initializations of several variables
thermal/core/power allocator: Use the lockless __thermal_cdev_update() function
thermal/core/fair share: Use the lockless __thermal_cdev_update() function
thermal/core/fair share: Lock the thermal zone while looping over instances
thermal/core/power_allocator: Update once cooling devices when temp is low
thermal/core/power_allocator: Maintain the device statistics from going stale
thermal/core: Create a helper __thermal_cdev_update() without a lock
dt-bindings: thermal: tsens: Document ipq8064 bindings
thermal/drivers/tsens: Add support for ipq8064-tsens
thermal/drivers/tsens: Drop unused define for msm8960
thermal/drivers/tsens: Replace custom 8960 apis with generic apis
thermal/drivers/tsens: Fix bug in sensor enable for msm8960
thermal/drivers/tsens: Use init_common for msm8960
thermal/drivers/tsens: Add VER_0 tsens version
thermal/drivers/tsens: Convert msm8960 to reg_field
thermal/drivers/tsens: Don't hardcode sensor slope
Documentation: driver-api: thermal: Remove thermal_notify_framework from documentation
thermal/core: Remove thermal_notify_framework
iwlwifi: mvm: tt: Replace thermal_notify_framework
dt-bindings: thermal: brcm,ns-thermal: Convert to the json-schema
...
Core:
- bpf:
- allow bpf programs calling kernel functions (initially to
reuse TCP congestion control implementations)
- enable task local storage for tracing programs - remove the
need to store per-task state in hash maps, and allow tracing
programs access to task local storage previously added for
BPF_LSM
- add bpf_for_each_map_elem() helper, allowing programs to
walk all map elements in a more robust and easier to verify
fashion
- sockmap: support UDP and cross-protocol BPF_SK_SKB_VERDICT
redirection
- lpm: add support for batched ops in LPM trie
- add BTF_KIND_FLOAT support - mostly to allow use of BTF
on s390 which has floats in its headers files
- improve BPF syscall documentation and extend the use of kdoc
parsing scripts we already employ for bpf-helpers
- libbpf, bpftool: support static linking of BPF ELF files
- improve support for encapsulation of L2 packets
- xdp: restructure redirect actions to avoid a runtime lookup,
improving performance by 4-8% in microbenchmarks
- xsk: build skb by page (aka generic zerocopy xmit) - improve
performance of software AF_XDP path by 33% for devices
which don't need headers in the linear skb part (e.g. virtio)
- nexthop: resilient next-hop groups - improve path stability
on next-hops group changes (incl. offload for mlxsw)
- ipv6: segment routing: add support for IPv4 decapsulation
- icmp: add support for RFC 8335 extended PROBE messages
- inet: use bigger hash table for IP ID generation
- tcp: deal better with delayed TX completions - make sure we don't
give up on fast TCP retransmissions only because driver is
slow in reporting that it completed transmitting the original
- tcp: reorder tcp_congestion_ops for better cache locality
- mptcp:
- add sockopt support for common TCP options
- add support for common TCP msg flags
- include multiple address ids in RM_ADDR
- add reset option support for resetting one subflow
- udp: GRO L4 improvements - improve 'forward' / 'frag_list'
co-existence with UDP tunnel GRO, allowing the first to take
place correctly even for encapsulated UDP traffic
- micro-optimize dev_gro_receive() and flow dissection, avoid
retpoline overhead on VLAN and TEB GRO
- use less memory for sysctls, add a new sysctl type, to allow using
u8 instead of "int" and "long" and shrink networking sysctls
- veth: allow GRO without XDP - this allows aggregating UDP
packets before handing them off to routing, bridge, OvS, etc.
- allow specifing ifindex when device is moved to another namespace
- netfilter:
- nft_socket: add support for cgroupsv2
- nftables: add catch-all set element - special element used
to define a default action in case normal lookup missed
- use net_generic infra in many modules to avoid allocating
per-ns memory unnecessarily
- xps: improve the xps handling to avoid potential out-of-bound
accesses and use-after-free when XPS change race with other
re-configuration under traffic
- add a config knob to turn off per-cpu netdev refcnt to catch
underflows in testing
Device APIs:
- add WWAN subsystem to organize the WWAN interfaces better and
hopefully start driving towards more unified and vendor-
-independent APIs
- ethtool:
- add interface for reading IEEE MIB stats (incl. mlx5 and
bnxt support)
- allow network drivers to dump arbitrary SFP EEPROM data,
current offset+length API was a poor fit for modern SFP
which define EEPROM in terms of pages (incl. mlx5 support)
- act_police, flow_offload: add support for packet-per-second
policing (incl. offload for nfp)
- psample: add additional metadata attributes like transit delay
for packets sampled from switch HW (and corresponding egress
and policy-based sampling in the mlxsw driver)
- dsa: improve support for sandwiched LAGs with bridge and DSA
- netfilter:
- flowtable: use direct xmit in topologies with IP
forwarding, bridging, vlans etc.
- nftables: counter hardware offload support
- Bluetooth:
- improvements for firmware download w/ Intel devices
- add support for reading AOSP vendor capabilities
- add support for virtio transport driver
- mac80211:
- allow concurrent monitor iface and ethernet rx decap
- set priority and queue mapping for injected frames
- phy: add support for Clause-45 PHY Loopback
- pci/iov: add sysfs MSI-X vector assignment interface
to distribute MSI-X resources to VFs (incl. mlx5 support)
New hardware/drivers:
- dsa: mv88e6xxx: add support for Marvell mv88e6393x -
11-port Ethernet switch with 8x 1-Gigabit Ethernet
and 3x 10-Gigabit interfaces.
- dsa: support for legacy Broadcom tags used on BCM5325, BCM5365
and BCM63xx switches
- Microchip KSZ8863 and KSZ8873; 3x 10/100Mbps Ethernet switches
- ath11k: support for QCN9074 a 802.11ax device
- Bluetooth: Broadcom BCM4330 and BMC4334
- phy: Marvell 88X2222 transceiver support
- mdio: add BCM6368 MDIO mux bus controller
- r8152: support RTL8153 and RTL8156 (USB Ethernet) chips
- mana: driver for Microsoft Azure Network Adapter (MANA)
- Actions Semi Owl Ethernet MAC
- can: driver for ETAS ES58X CAN/USB interfaces
Pure driver changes:
- add XDP support to: enetc, igc, stmmac
- add AF_XDP support to: stmmac
- virtio:
- page_to_skb() use build_skb when there's sufficient tailroom
(21% improvement for 1000B UDP frames)
- support XDP even without dedicated Tx queues - share the Tx
queues with the stack when necessary
- mlx5:
- flow rules: add support for mirroring with conntrack,
matching on ICMP, GTP, flex filters and more
- support packet sampling with flow offloads
- persist uplink representor netdev across eswitch mode
changes
- allow coexistence of CQE compression and HW time-stamping
- add ethtool extended link error state reporting
- ice, iavf: support flow filters, UDP Segmentation Offload
- dpaa2-switch:
- move the driver out of staging
- add spanning tree (STP) support
- add rx copybreak support
- add tc flower hardware offload on ingress traffic
- ionic:
- implement Rx page reuse
- support HW PTP time-stamping
- octeon: support TC hardware offloads - flower matching on ingress
and egress ratelimitting.
- stmmac:
- add RX frame steering based on VLAN priority in tc flower
- support frame preemption (FPE)
- intel: add cross time-stamping freq difference adjustment
- ocelot:
- support forwarding of MRP frames in HW
- support multiple bridges
- support PTP Sync one-step timestamping
- dsa: mv88e6xxx, dpaa2-switch: offload bridge port flags like
learning, flooding etc.
- ipa: add IPA v4.5, v4.9 and v4.11 support (Qualcomm SDX55, SM8350,
SC7280 SoCs)
- mt7601u: enable TDLS support
- mt76:
- add support for 802.3 rx frames (mt7915/mt7615)
- mt7915 flash pre-calibration support
- mt7921/mt7663 runtime power management fixes
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
-----BEGIN PGP SIGNATURE-----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=vcbA
-----END PGP SIGNATURE-----
Merge tag 'net-next-5.13' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-next
Pull networking updates from Jakub Kicinski:
"Core:
- bpf:
- allow bpf programs calling kernel functions (initially to
reuse TCP congestion control implementations)
- enable task local storage for tracing programs - remove the
need to store per-task state in hash maps, and allow tracing
programs access to task local storage previously added for
BPF_LSM
- add bpf_for_each_map_elem() helper, allowing programs to walk
all map elements in a more robust and easier to verify fashion
- sockmap: support UDP and cross-protocol BPF_SK_SKB_VERDICT
redirection
- lpm: add support for batched ops in LPM trie
- add BTF_KIND_FLOAT support - mostly to allow use of BTF on
s390 which has floats in its headers files
- improve BPF syscall documentation and extend the use of kdoc
parsing scripts we already employ for bpf-helpers
- libbpf, bpftool: support static linking of BPF ELF files
- improve support for encapsulation of L2 packets
- xdp: restructure redirect actions to avoid a runtime lookup,
improving performance by 4-8% in microbenchmarks
- xsk: build skb by page (aka generic zerocopy xmit) - improve
performance of software AF_XDP path by 33% for devices which don't
need headers in the linear skb part (e.g. virtio)
- nexthop: resilient next-hop groups - improve path stability on
next-hops group changes (incl. offload for mlxsw)
- ipv6: segment routing: add support for IPv4 decapsulation
- icmp: add support for RFC 8335 extended PROBE messages
- inet: use bigger hash table for IP ID generation
- tcp: deal better with delayed TX completions - make sure we don't
give up on fast TCP retransmissions only because driver is slow in
reporting that it completed transmitting the original
- tcp: reorder tcp_congestion_ops for better cache locality
- mptcp:
- add sockopt support for common TCP options
- add support for common TCP msg flags
- include multiple address ids in RM_ADDR
- add reset option support for resetting one subflow
- udp: GRO L4 improvements - improve 'forward' / 'frag_list'
co-existence with UDP tunnel GRO, allowing the first to take place
correctly even for encapsulated UDP traffic
- micro-optimize dev_gro_receive() and flow dissection, avoid
retpoline overhead on VLAN and TEB GRO
- use less memory for sysctls, add a new sysctl type, to allow using
u8 instead of "int" and "long" and shrink networking sysctls
- veth: allow GRO without XDP - this allows aggregating UDP packets
before handing them off to routing, bridge, OvS, etc.
- allow specifing ifindex when device is moved to another namespace
- netfilter:
- nft_socket: add support for cgroupsv2
- nftables: add catch-all set element - special element used to
define a default action in case normal lookup missed
- use net_generic infra in many modules to avoid allocating
per-ns memory unnecessarily
- xps: improve the xps handling to avoid potential out-of-bound
accesses and use-after-free when XPS change race with other
re-configuration under traffic
- add a config knob to turn off per-cpu netdev refcnt to catch
underflows in testing
Device APIs:
- add WWAN subsystem to organize the WWAN interfaces better and
hopefully start driving towards more unified and vendor-
independent APIs
- ethtool:
- add interface for reading IEEE MIB stats (incl. mlx5 and bnxt
support)
- allow network drivers to dump arbitrary SFP EEPROM data,
current offset+length API was a poor fit for modern SFP which
define EEPROM in terms of pages (incl. mlx5 support)
- act_police, flow_offload: add support for packet-per-second
policing (incl. offload for nfp)
- psample: add additional metadata attributes like transit delay for
packets sampled from switch HW (and corresponding egress and
policy-based sampling in the mlxsw driver)
- dsa: improve support for sandwiched LAGs with bridge and DSA
- netfilter:
- flowtable: use direct xmit in topologies with IP forwarding,
bridging, vlans etc.
- nftables: counter hardware offload support
- Bluetooth:
- improvements for firmware download w/ Intel devices
- add support for reading AOSP vendor capabilities
- add support for virtio transport driver
- mac80211:
- allow concurrent monitor iface and ethernet rx decap
- set priority and queue mapping for injected frames
- phy: add support for Clause-45 PHY Loopback
- pci/iov: add sysfs MSI-X vector assignment interface to distribute
MSI-X resources to VFs (incl. mlx5 support)
New hardware/drivers:
- dsa: mv88e6xxx: add support for Marvell mv88e6393x - 11-port
Ethernet switch with 8x 1-Gigabit Ethernet and 3x 10-Gigabit
interfaces.
- dsa: support for legacy Broadcom tags used on BCM5325, BCM5365 and
BCM63xx switches
- Microchip KSZ8863 and KSZ8873; 3x 10/100Mbps Ethernet switches
- ath11k: support for QCN9074 a 802.11ax device
- Bluetooth: Broadcom BCM4330 and BMC4334
- phy: Marvell 88X2222 transceiver support
- mdio: add BCM6368 MDIO mux bus controller
- r8152: support RTL8153 and RTL8156 (USB Ethernet) chips
- mana: driver for Microsoft Azure Network Adapter (MANA)
- Actions Semi Owl Ethernet MAC
- can: driver for ETAS ES58X CAN/USB interfaces
Pure driver changes:
- add XDP support to: enetc, igc, stmmac
- add AF_XDP support to: stmmac
- virtio:
- page_to_skb() use build_skb when there's sufficient tailroom
(21% improvement for 1000B UDP frames)
- support XDP even without dedicated Tx queues - share the Tx
queues with the stack when necessary
- mlx5:
- flow rules: add support for mirroring with conntrack, matching
on ICMP, GTP, flex filters and more
- support packet sampling with flow offloads
- persist uplink representor netdev across eswitch mode changes
- allow coexistence of CQE compression and HW time-stamping
- add ethtool extended link error state reporting
- ice, iavf: support flow filters, UDP Segmentation Offload
- dpaa2-switch:
- move the driver out of staging
- add spanning tree (STP) support
- add rx copybreak support
- add tc flower hardware offload on ingress traffic
- ionic:
- implement Rx page reuse
- support HW PTP time-stamping
- octeon: support TC hardware offloads - flower matching on ingress
and egress ratelimitting.
- stmmac:
- add RX frame steering based on VLAN priority in tc flower
- support frame preemption (FPE)
- intel: add cross time-stamping freq difference adjustment
- ocelot:
- support forwarding of MRP frames in HW
- support multiple bridges
- support PTP Sync one-step timestamping
- dsa: mv88e6xxx, dpaa2-switch: offload bridge port flags like
learning, flooding etc.
- ipa: add IPA v4.5, v4.9 and v4.11 support (Qualcomm SDX55, SM8350,
SC7280 SoCs)
- mt7601u: enable TDLS support
- mt76:
- add support for 802.3 rx frames (mt7915/mt7615)
- mt7915 flash pre-calibration support
- mt7921/mt7663 runtime power management fixes"
* tag 'net-next-5.13' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-next: (2451 commits)
net: selftest: fix build issue if INET is disabled
net: netrom: nr_in: Remove redundant assignment to ns
net: tun: Remove redundant assignment to ret
net: phy: marvell: add downshift support for M88E1240
net: dsa: ksz: Make reg_mib_cnt a u8 as it never exceeds 255
net/sched: act_ct: Remove redundant ct get and check
icmp: standardize naming of RFC 8335 PROBE constants
bpf, selftests: Update array map tests for per-cpu batched ops
bpf: Add batched ops support for percpu array
bpf: Implement formatted output helpers with bstr_printf
seq_file: Add a seq_bprintf function
sfc: adjust efx->xdp_tx_queue_count with the real number of initialized queues
net:nfc:digital: Fix a double free in digital_tg_recv_dep_req
net: fix a concurrency bug in l2tp_tunnel_register()
net/smc: Remove redundant assignment to rc
mpls: Remove redundant assignment to err
llc2: Remove redundant assignment to rc
net/tls: Remove redundant initialization of record
rds: Remove redundant assignment to nr_sig
dt-bindings: net: mdio-gpio: add compatible for microchip,mdio-smi0
...
- rtmutex cleanup & spring cleaning pass that removes ~400 lines of code
- Futex simplifications & cleanups
- Add debugging to the CSD code, to help track down a tenacious race (or hw problem)
- Add lockdep_assert_not_held(), to allow code to require a lock to not be held,
and propagate this into the ath10k driver
- Misc LKMM documentation updates
- Misc KCSAN updates: cleanups & documentation updates
- Misc fixes and cleanups
- Fix locktorture bugs with ww_mutexes
Signed-off-by: Ingo Molnar <mingo@kernel.org>
-----BEGIN PGP SIGNATURE-----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=cOOk
-----END PGP SIGNATURE-----
Merge tag 'locking-core-2021-04-28' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull locking updates from Ingo Molnar:
- rtmutex cleanup & spring cleaning pass that removes ~400 lines of
code
- Futex simplifications & cleanups
- Add debugging to the CSD code, to help track down a tenacious race
(or hw problem)
- Add lockdep_assert_not_held(), to allow code to require a lock to not
be held, and propagate this into the ath10k driver
- Misc LKMM documentation updates
- Misc KCSAN updates: cleanups & documentation updates
- Misc fixes and cleanups
- Fix locktorture bugs with ww_mutexes
* tag 'locking-core-2021-04-28' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (44 commits)
kcsan: Fix printk format string
static_call: Relax static_call_update() function argument type
static_call: Fix unused variable warn w/o MODULE
locking/rtmutex: Clean up signal handling in __rt_mutex_slowlock()
locking/rtmutex: Restrict the trylock WARN_ON() to debug
locking/rtmutex: Fix misleading comment in rt_mutex_postunlock()
locking/rtmutex: Consolidate the fast/slowpath invocation
locking/rtmutex: Make text section and inlining consistent
locking/rtmutex: Move debug functions as inlines into common header
locking/rtmutex: Decrapify __rt_mutex_init()
locking/rtmutex: Remove pointless CONFIG_RT_MUTEXES=n stubs
locking/rtmutex: Inline chainwalk depth check
locking/rtmutex: Move rt_mutex_debug_task_free() to rtmutex.c
locking/rtmutex: Remove empty and unused debug stubs
locking/rtmutex: Consolidate rt_mutex_init()
locking/rtmutex: Remove output from deadlock detector
locking/rtmutex: Remove rtmutex deadlock tester leftovers
locking/rtmutex: Remove rt_mutex_timed_lock()
MAINTAINERS: Add myself as futex reviewer
locking/mutex: Remove repeated declaration
...
Core changes:
- Provide IRQF_NO_AUTOEN as a flag for request*_irq() so drivers can be
cleaned up which either use a seperate mechanism to prevent auto-enable
at request time or have a racy mechanism which disables the interrupt
right after request.
- Get rid of the last usage of irq_create_identity_mapping() and remove
the interface.
- An overhaul of tasklet_disable(). Most usage sites of tasklet_disable()
are in task context and usually in cleanup, teardown code pathes.
tasklet_disable() spinwaits for a tasklet which is currently executed.
That's not only a problem for PREEMPT_RT where this can lead to a live
lock when the disabling task preempts the softirq thread. It's also
problematic in context of virtualization when the vCPU which runs the
tasklet is scheduled out and the disabling code has to spin wait until
it's scheduled back in. Though there are a few code pathes which invoke
tasklet_disable() from non-sleepable context. For these a new disable
variant which still spinwaits is provided which allows to switch
tasklet_disable() to a sleep wait mechanism. For the atomic use cases
this does not solve the live lock issue on PREEMPT_RT. That is mitigated
by blocking on the RT specific softirq lock.
- The PREEMPT_RT specific implementation of softirq processing and
local_bh_disable/enable().
On RT enabled kernels soft interrupt processing happens always in task
context and all interrupt handlers, which are not explicitly marked to
be invoked in hard interrupt context are forced into task context as
well. This allows to protect against softirq processing with a per
CPU lock, which in turn allows to make BH disabled regions preemptible.
Most of the softirq handling code is still shared. The RT/non-RT
specific differences are addressed with a set of inline functions which
provide the context specific functionality. The local_bh_disable() /
local_bh_enable() mechanism are obviously seperate.
- The usual set of small improvements and cleanups
Driver changes:
- New drivers for Nuvoton WPCM450 and DT 79rc3243x interrupt controllers
- Extended functionality for MStar, STM32 and SC7280 irq chips
- Enhanced robustness for ARM GICv3/4.1 drivers
- The usual set of cleanups and improvements all over the place
-----BEGIN PGP SIGNATURE-----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=id4G
-----END PGP SIGNATURE-----
Merge tag 'irq-core-2021-04-26' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull irq updates from Thomas Gleixner:
"The usual updates from the irq departement:
Core changes:
- Provide IRQF_NO_AUTOEN as a flag for request*_irq() so drivers can
be cleaned up which either use a seperate mechanism to prevent
auto-enable at request time or have a racy mechanism which disables
the interrupt right after request.
- Get rid of the last usage of irq_create_identity_mapping() and
remove the interface.
- An overhaul of tasklet_disable().
Most usage sites of tasklet_disable() are in task context and
usually in cleanup, teardown code pathes. tasklet_disable()
spinwaits for a tasklet which is currently executed. That's not
only a problem for PREEMPT_RT where this can lead to a live lock
when the disabling task preempts the softirq thread. It's also
problematic in context of virtualization when the vCPU which runs
the tasklet is scheduled out and the disabling code has to spin
wait until it's scheduled back in.
There are a few code pathes which invoke tasklet_disable() from
non-sleepable context. For these a new disable variant which still
spinwaits is provided which allows to switch tasklet_disable() to a
sleep wait mechanism. For the atomic use cases this does not solve
the live lock issue on PREEMPT_RT. That is mitigated by blocking on
the RT specific softirq lock.
- The PREEMPT_RT specific implementation of softirq processing and
local_bh_disable/enable().
On RT enabled kernels soft interrupt processing happens always in
task context and all interrupt handlers, which are not explicitly
marked to be invoked in hard interrupt context are forced into task
context as well. This allows to protect against softirq processing
with a per CPU lock, which in turn allows to make BH disabled
regions preemptible.
Most of the softirq handling code is still shared. The RT/non-RT
specific differences are addressed with a set of inline functions
which provide the context specific functionality. The
local_bh_disable() / local_bh_enable() mechanism are obviously
seperate.
- The usual set of small improvements and cleanups
Driver changes:
- New drivers for Nuvoton WPCM450 and DT 79rc3243x interrupt
controllers
- Extended functionality for MStar, STM32 and SC7280 irq chips
- Enhanced robustness for ARM GICv3/4.1 drivers
- The usual set of cleanups and improvements all over the place"
* tag 'irq-core-2021-04-26' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (53 commits)
irqchip/xilinx: Expose Kconfig option for Zynq/ZynqMP
irqchip/gic-v3: Do not enable irqs when handling spurious interrups
dt-bindings: interrupt-controller: Add IDT 79RC3243x Interrupt Controller
irqchip: Add support for IDT 79rc3243x interrupt controller
irqdomain: Drop references to recusive irqdomain setup
irqdomain: Get rid of irq_create_strict_mappings()
irqchip/jcore-aic: Kill use of irq_create_strict_mappings()
ARM: PXA: Kill use of irq_create_strict_mappings()
irqchip/gic-v4.1: Disable vSGI upon (GIC CPUIF < v4.1) detection
irqchip/tb10x: Use 'fallthrough' to eliminate a warning
genirq: Reduce irqdebug cacheline bouncing
kernel: Initialize cpumask before parsing
irqchip/wpcm450: Drop COMPILE_TEST
irqchip/irq-mst: Support polarity configuration
irqchip: Add driver for WPCM450 interrupt controller
dt-bindings: interrupt-controller: Add nuvoton, wpcm450-aic
dt-bindings: qcom,pdc: Add compatible for sc7280
irqchip/stm32: Add usart instances exti direct event support
irqchip/gic-v3: Fix OF_BAD_ADDR error handling
irqchip/sifive-plic: Mark two global variables __ro_after_init
...
* testmode improvements
* bugfixes
* device tree power limits support for 7615 and newer
* hardware recovery fixes
* mt7663 reset/init fixes
* mt7915 flash pre-calibration support
* mt7921/mt7663 runtime power management fixes
-----BEGIN PGP SIGNATURE-----
Comment: GPGTools - http://gpgtools.org
iEYEABECAAYFAmCAdekACgkQ130UHQKnbvX91ACgph/7sPQQNW5x0VsLDTWV/2V8
kDAAn329OFt20Mb/Zhj2g1IBZ4+jugsx
=d2/2
-----END PGP SIGNATURE-----
Merge tag 'mt76-for-kvalo-2021-04-21' of https://github.com/nbd168/wireless
mt76 patches for 5.13
* testmode improvements
* bugfixes
* device tree power limits support for 7615 and newer
* hardware recovery fixes
* mt7663 reset/init fixes
* mt7915 flash pre-calibration support
* mt7921/mt7663 runtime power management fixes
# gpg: Signature made Wed 21 Apr 2021 09:58:49 PM EEST using DSA key ID 02A76EF5
# gpg: Good signature from "Felix Fietkau <nbd@nbd.name>"
# gpg: WARNING: This key is not certified with a trusted signature!
# gpg: There is no indication that the signature belongs to the owner.
# Primary key fingerprint: 75D1 1A7D 91A7 710F 4900 42EF D77D 141D 02A7 6EF5
Function qtnf_event_handle_external_auth calls memcpy without
checking the length.
A user could control that length and trigger a buffer overflow.
Fix by checking the length is within the maximum allowed size.
Signed-off-by: Lee Gibson <leegib@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210419145842.345787-1-leegib@gmail.com
The size of the buffer than can be written to is currently incorrect, it is
always the size of the entire buffer even though the snprintf is writing
as position pos into the buffer. Fix this by setting the buffer size to be
the number of bytes left in the buffer, namely sizeof(buf) - pos.
Addresses-Coverity: ("Out-of-bounds access")
Fixes: 7b0e2c4f6b ("wlcore: fix overlapping snprintf arguments in debugfs")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210419141405.180582-1-colin.king@canonical.com
Fix the following out-of-bounds warnings by adding a new structure
wl3501_req instead of duplicating the same members in structure
wl3501_join_req and wl3501_scan_confirm:
arch/x86/include/asm/string_32.h:182:25: warning: '__builtin_memcpy' offset [39, 108] from the object at 'sig' is out of the bounds of referenced subobject 'beacon_period' with type 'short unsigned int' at offset 36 [-Warray-bounds]
arch/x86/include/asm/string_32.h:182:25: warning: '__builtin_memcpy' offset [25, 95] from the object at 'sig' is out of the bounds of referenced subobject 'beacon_period' with type 'short unsigned int' at offset 22 [-Warray-bounds]
Refactor the code, accordingly:
$ pahole -C wl3501_req drivers/net/wireless/wl3501_cs.o
struct wl3501_req {
u16 beacon_period; /* 0 2 */
u16 dtim_period; /* 2 2 */
u16 cap_info; /* 4 2 */
u8 bss_type; /* 6 1 */
u8 bssid[6]; /* 7 6 */
struct iw_mgmt_essid_pset ssid; /* 13 34 */
struct iw_mgmt_ds_pset ds_pset; /* 47 3 */
struct iw_mgmt_cf_pset cf_pset; /* 50 8 */
struct iw_mgmt_ibss_pset ibss_pset; /* 58 4 */
struct iw_mgmt_data_rset bss_basic_rset; /* 62 10 */
/* size: 72, cachelines: 2, members: 10 */
/* last cacheline: 8 bytes */
};
$ pahole -C wl3501_join_req drivers/net/wireless/wl3501_cs.o
struct wl3501_join_req {
u16 next_blk; /* 0 2 */
u8 sig_id; /* 2 1 */
u8 reserved; /* 3 1 */
struct iw_mgmt_data_rset operational_rset; /* 4 10 */
u16 reserved2; /* 14 2 */
u16 timeout; /* 16 2 */
u16 probe_delay; /* 18 2 */
u8 timestamp[8]; /* 20 8 */
u8 local_time[8]; /* 28 8 */
struct wl3501_req req; /* 36 72 */
/* size: 108, cachelines: 2, members: 10 */
/* last cacheline: 44 bytes */
};
$ pahole -C wl3501_scan_confirm drivers/net/wireless/wl3501_cs.o
struct wl3501_scan_confirm {
u16 next_blk; /* 0 2 */
u8 sig_id; /* 2 1 */
u8 reserved; /* 3 1 */
u16 status; /* 4 2 */
char timestamp[8]; /* 6 8 */
char localtime[8]; /* 14 8 */
struct wl3501_req req; /* 22 72 */
/* --- cacheline 1 boundary (64 bytes) was 30 bytes ago --- */
u8 rssi; /* 94 1 */
/* size: 96, cachelines: 2, members: 8 */
/* padding: 1 */
/* last cacheline: 32 bytes */
};
The problem is that the original code is trying to copy data into a
bunch of struct members adjacent to each other in a single call to
memcpy(). Now that a new struct wl3501_req enclosing all those adjacent
members is introduced, memcpy() doesn't overrun the length of
&sig.beacon_period and &this->bss_set[i].beacon_period, because the
address of the new struct object _req_ is used as the destination,
instead.
This helps with the ongoing efforts to globally enable -Warray-bounds
and get us closer to being able to tighten the FORTIFY_SOURCE routines
on memcpy().
Link: https://github.com/KSPP/linux/issues/109
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Gustavo A. R. Silva <gustavoars@kernel.org>
Reviewed-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1fbaf516da763b50edac47d792a9145aa4482e29.1618442265.git.gustavoars@kernel.org
Fix the following out-of-bounds warnings by enclosing structure members
daddr and saddr into new struct addr, in structures wl3501_md_req and
wl3501_md_ind:
arch/x86/include/asm/string_32.h:182:25: warning: '__builtin_memcpy' offset [18, 23] from the object at 'sig' is out of the bounds of referenced subobject 'daddr' with type 'u8[6]' {aka 'unsigned char[6]'} at offset 11 [-Warray-bounds]
arch/x86/include/asm/string_32.h:182:25: warning: '__builtin_memcpy' offset [18, 23] from the object at 'sig' is out of the bounds of referenced subobject 'daddr' with type 'u8[6]' {aka 'unsigned char[6]'} at offset 11 [-Warray-bounds]
Refactor the code, accordingly:
$ pahole -C wl3501_md_req drivers/net/wireless/wl3501_cs.o
struct wl3501_md_req {
u16 next_blk; /* 0 2 */
u8 sig_id; /* 2 1 */
u8 routing; /* 3 1 */
u16 data; /* 4 2 */
u16 size; /* 6 2 */
u8 pri; /* 8 1 */
u8 service_class; /* 9 1 */
struct {
u8 daddr[6]; /* 10 6 */
u8 saddr[6]; /* 16 6 */
} addr; /* 10 12 */
/* size: 22, cachelines: 1, members: 8 */
/* last cacheline: 22 bytes */
};
$ pahole -C wl3501_md_ind drivers/net/wireless/wl3501_cs.o
struct wl3501_md_ind {
u16 next_blk; /* 0 2 */
u8 sig_id; /* 2 1 */
u8 routing; /* 3 1 */
u16 data; /* 4 2 */
u16 size; /* 6 2 */
u8 reception; /* 8 1 */
u8 pri; /* 9 1 */
u8 service_class; /* 10 1 */
struct {
u8 daddr[6]; /* 11 6 */
u8 saddr[6]; /* 17 6 */
} addr; /* 11 12 */
/* size: 24, cachelines: 1, members: 9 */
/* padding: 1 */
/* last cacheline: 24 bytes */
};
The problem is that the original code is trying to copy data into a
couple of arrays adjacent to each other in a single call to memcpy().
Now that a new struct _addr_ enclosing those two adjacent arrays
is introduced, memcpy() doesn't overrun the length of &sig.daddr[0]
and &sig.daddr, because the address of the new struct object _addr_
is used, instead.
This helps with the ongoing efforts to globally enable -Warray-bounds
and get us closer to being able to tighten the FORTIFY_SOURCE routines
on memcpy().
Link: https://github.com/KSPP/linux/issues/109
Reported-by: kernel test robot <lkp@intel.com>
Reviewed-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Gustavo A. R. Silva <gustavoars@kernel.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/d260fe56aed7112bff2be5b4d152d03ad7b78e78.1618442265.git.gustavoars@kernel.org
ath10k_wmi_tlv_op_pull_peer_stats_info() could try to unlock RCU lock
winthout locking it first when peer reason doesn't match the valid
cases for this function.
Add a default case to return without unlocking.
Fixes: 09078368d5 ("ath10k: hold RCU lock when calling ieee80211_find_sta_by_ifaddr()")
Reported-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Shuah Khan <skhan@linuxfoundation.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210406230228.31301-1-skhan@linuxfoundation.org
In ath10k_htc_send_bundle, the bundle_skb could be freed by
dev_kfree_skb_any(bundle_skb). But the bundle_skb is used later
by bundle_skb->len.
As skb_len = bundle_skb->len, my patch replaces bundle_skb->len to
skb_len after the bundle_skb was freed.
Fixes: c8334512f3 ("ath10k: add htt TX bundle for sdio")
Signed-off-by: Lv Yunlong <lyl2019@mail.ustc.edu.cn>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210329120154.8963-1-lyl2019@mail.ustc.edu.cn
When the error check in ath9k_hw_read_revisions() was added, it checked for
-EIO which is what ath9k_regread() in the ath9k_htc driver uses. However,
for plain ath9k, the register read function uses ioread32(), which just
returns -1 on error. So if such a read fails, it still gets passed through
and ends up as a weird mac revision in the log output.
Fix this by changing ath9k_regread() to return -1 on error like ioread32()
does, and fix the error check to look for that instead of -EIO.
Fixes: 2f90c7e5d0 ("ath9k: Check for errors when reading SREV register")
Signed-off-by: Toke Høiland-Jørgensen <toke@redhat.com>
Reviewed-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210326180819.142480-1-toke@redhat.com
thermal_notify_framework just updates for a single trip point where as
thermal_zone_device_update does other bookkeeping like updating the
temperature of the thermal zone and setting the next trip point etc.
Replace thermal_notify_framework with thermal_zone_device_update as the
later is more thorough.
Acked-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Thara Gopinath <thara.gopinath@linaro.org>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20210122023406.3500424-2-thara.gopinath@linaro.org
Check dummy reg to reinitialized WPDMA during driver_own operation
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
In order to remove duplicated code, move mt76_token_init in
mt76_alloc_device routine
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Precision %.*s was intended instead of width %*s. The original code
is potentially an information leak.
Fixes: c7cc5ec573 ("mt76: mt7921: rework mt7921_mcu_debug_msg_event routine")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Precision %.*s was intended instead of width %*s. The original code
will still print unintended data from beyond the end of skb->data.
Fixes: 665b2c780d ("mt76: mt7915: limit firmware log message printk to buffer length")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Precision "%.*s" was intended instead of width "%*s". The original code
will print garbage from beyond the end of the skb->data.
Fixes: d76d6c3ba2 ("mt76: mt7615: limit firmware log message printk to buffer length")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Introduce napi_threaded debugfs knob in order to enable/disable NAPI
threaded support
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
mt7921_mcu_sta_add will be used to add and remove wtbl entries.
Create broadcast wtbl entry after AP association
Co-developed-by: Deren Wu <deren.wu@mediatek.com>
Signed-off-by: Deren Wu <deren.wu@mediatek.com>
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
mt7921_stop should put device in fw_own state to reduce
power consumption.
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
In order to wake the device less frequently and so reduce power
consumpation, unschedule mac_work before going to sleep
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Similar to mt7921, introduce awake and doze time accounting
for runtime pm.
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Increase mt7921 mac work timeout in oder to have move sleep
opportunities
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
since mcu_reset it used only by mt7921, move the reset callback to
mt7921_mcu_parse_response routine and get rid of the function pointer.
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Do not read rf value from efuse when driver is configured to
use flash mode.
Tested-by: Bruce Chuang <bruce-ss.chuang@mediatek.com>
Signed-off-by: Shayne Chen <shayne.chen@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Move token management in mt76 common module since it is shared between
mt7615, mt7915 and mt7921 drivers
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Move token_lock, token and token_count data structures in mt76_dev.
This is a preliminary patch to move token management in mt76 common
module since it is shared by mt7615, mt7915 and mt7921 drivers.
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Enable the deep sleep mode in suspend handler to reduce the power
consumption further.
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Introduce mt76_connac_mcu_set_deep_sleep to enable deep sleep mode
and will be activated immediately when the host returns the ownership
to the device.
Co-developed-by: Leon Yen <leon.yen@mediatek.com>
Signed-off-by: Leon Yen <leon.yen@mediatek.com>
Co-developed-by: YN Chen <YN.Chen@mediatek.com>
Signed-off-by: YN Chen <YN.Chen@mediatek.com>
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Add mt7921_wpdma_reinit_cond to check dummy reg if driver needs to
reinitialized WPDMA after driver_own operation
Co-developed-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Co-developed-by: Leon Yen <leon.yen@mediatek.com>
Signed-off-by: Leon Yen <leon.yen@mediatek.com>
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Introduce mt7921_dma_enable and mt7921_dma_disable utilities routine in
order for code reusing between mt7921_dma_reset and mt7921_dma_init.
This is a preliminary patch to reset dma during device driver_own
request.
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Introduce mt7921_wpdma_reset routine to reset wpdma during chip reset
or driver_own request.
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Move mt7921_dma_reset routine in dma.c and make mt7921_dma_prefetch
static. Moreover add force parameter to mt7921_dma_reset signature.
This is a preliminary patch to reset dma mt7921_mcu_drv_pmctrl.
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Greg Kroah-Hartman