When SCSI command is received with task attribute not set, set it to SIMPLE.
Previously it is set to untagged. This causes the firmware to fail the commands.
Signed-off-by: Sreekanth Reddy <Sreekanth.Reddy@lsi.com>
Cc: stable@vger.kernel.org
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Modified device scan routine so each configuration page read breaks from the
while loop when the ioc_status is not equal to MPI2_IOCSTATUS_SUCCESS.
[jejb: checkpatch fixes]
Signed-off-by: Sreekanth Reddy <Sreekanth.Reddy@lsi.com>
Cc: stable@vger.kernel.org
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Updated the mpt2sas driver code that issues hard reset to comply with the
timing requirements mentioned in MPI specifications rev V.
[jejb: checpatch fixes]
Signed-off-by: Sreekanth Reddy <Sreekanth.Reddy@lsi.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Change set in MPI 2.0 Rev W(2.00.15) specification and 2.00.27 header files
1. Added a bit to the IOCExceptions field of the IOCFacts Reply to indicate
that the IOC detected a partial memory failure.
2. Added ElapsedSeconds field to RAID Volume Indicator Structure. Added
Elapsed Seconds Valid flag to Flags field of this structure.
3. Added ElapsedSeconds field to Integrated RAID Operations Status Event Data.
4. In the IOCSettings field of BIOS Page 1, modified the Adapter Support bits
description to specify X86 BIOS.
5. Toolbox Diagnostic CLI Tool Request may now use chain elements in the SGL.
Signed-off-by: Sreekanth Reddy <Sreekanth.Reddy@lsi.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Missing delay is not getting set properly. The reason is that it is not
defined in the same file from where it is being invoked. The fix is to move
the missing delay module parameter from mpt2sas_base.c to mpt2sas_scsh.c.
Signed-off-by: Sreekanth Reddy <Sreekanth.Reddy@lsi.com>
Cc: stable@vger.kernel.org
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
This patch uses module_platform_driver_probe() macro which makes
the code smaller and simpler.
Acked-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
This patch uses module_platform_driver_probe() macro which makes
the code smaller and simpler.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Callers of skb_seq_read() are currently forced to call skb_abort_seq_read()
even when consuming all the data because the last call to skb_seq_read (the
one that returns 0 to indicate the end) fails to unmap the last fragment page.
With this patch callers will be allowed to traverse the SKB data by calling
skb_prepare_seq_read() once and repeatedly calling skb_seq_read() as originally
intended (and documented in the original commit 677e90eda), that is, only call
skb_abort_seq_read() if the sequential read is actually aborted.
Signed-off-by: Wedson Almeida Filho <wedsonaf@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull SCSI target fixes from Nicholas Bellinger:
"Included is the recent tcm_qla2xxx residual underrun length fix from
Roland, along with Joern's iscsi-target patch for session_lock
breakage within iscsit_stop_time2retain_timer() code. Both are CC'ed
to stable.
The remaining two are specific to recent iscsi-target + iser
conversion changes. One drops some left-over debug noise, and Andy's
patch fixes configfs attribute handling during an explicit network
portal feature bit disable when iser-target is unsupported."
* git://git.kernel.org/pub/scm/linux/kernel/git/nab/target-pending:
iscsi-target: Remove left over v3.10-rc debug printks
target/iscsi: Fix op=disable + error handling cases in np_store_iser
tcm_qla2xxx: Fix residual for underrun commands that fail
target/iscsi: don't corrupt bh_count in iscsit_stop_time2retain_timer()
Comment from original 2012 patch:
In all our testing this function has never returned true. However, the
dropping of hardware_lock necessary to call this function seems to cause
a use-after-free we manage to hit rather frequently. Given this
cost-benefit ratio, I'm willing to remove some 100 lines of code.
And since the same problem exists around shutdown_sess and put_sess,
this patch changes them from taking the hardware_lock to requiring the
hardware_lock to be taken. In most cases the caller already had the
lock and had to drop it for the called method to reacquire it. At best
that hurts performance and in rare instances it causes races with fatal
consequences.
We dropped the original 2012 patch when upgrading our kernel and it took
us nearly half a year to discover we still need it.
(nab: Fix qla_tgt_sess reference in tcm_qla2xxx_put_sess)
Signed-off-by: Joern Engel <joern@logfs.org>
Cc: Giridhar Malavali <giridhar.malavali@qlogic.com>
Cc: Chad Dupuis <chad.dupuis@qlogic.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Conflicts:
drivers/net/wireless/ath/ath9k/Kconfig
drivers/net/xen-netback/netback.c
net/batman-adv/bat_iv_ogm.c
net/wireless/nl80211.c
The ath9k Kconfig conflict was a change of a Kconfig option name right
next to the deletion of another option.
The xen-netback conflict was overlapping changes involving the
handling of the notify list in xen_netbk_rx_action().
Batman conflict resolution provided by Antonio Quartulli, basically
keep everything in both conflict hunks.
The nl80211 conflict is a little more involved. In 'net' we added a
dynamic memory allocation to nl80211_dump_wiphy() to fix a race that
Linus reported. Meanwhile in 'net-next' the handlers were converted
to use pre and post doit handlers which use a flag to determine
whether to hold the RTNL mutex around the operation.
However, the dump handlers to not use this logic. Instead they have
to explicitly do the locking. There were apparent bugs in the
conversion of nl80211_dump_wiphy() in that we were not dropping the
RTNL mutex in all the return paths, and it seems we very much should
be doing so. So I fixed that whilst handling the overlapping changes.
To simplify the initial returns, I take the RTNL mutex after we try
to allocate 'tb'.
Signed-off-by: David S. Miller <davem@davemloft.net>
ARM cannot handle udelay for more than 2 miliseconds, so we
should use mdelay instead for those.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: GOTO Masanori <gotom@debian.or.jp>
Cc: YOKOTA Hiroshi <yokota@netlab.is.tsukuba.ac.jp>
Cc: "James E.J. Bottomley" <JBottomley@parallels.com>
Cc: linux-scsi@vger.kernel.org
Correct spelling typo in printk within various drivers.
Signed-off-by: Masanari Iida <standby24x7@gmail.com>
Acked-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The change set of 1a37e412, "net: Use 16bits for *_headers fields
of struct skbuff" converted from sk_buff_data_t into 16bit integer.
So skb->tail needs to be converted to skb_tail_pointer(skb).
Found by inspection. Compile tested only.
Cc: Simon Horman <horms@verge.net.au>
Cc: Li RongQing <roy.qing.li@gmail.com>
Cc: linux-scsi@vger.kernel.org
Signed-off-by: Isaku Yamahata <yamahata@valinux.co.jp>
Acked-by: Simon Horman <horms@verge.net.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
When you copy some code, you are supposed to read it. If nothing else,
there's a chance to spot and fix an obvious bug instead of sharing it...
X-Song: "I Got It From Agnes", by Tom Lehrer
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
[ Tom Lehrer? You're dating yourself, Al ]
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Suppose an initiator sends a DATA IN command with an allocation length
shorter than the FC transfer length -- we get a target message like
TARGET_CORE[qla2xxx]: Expected Transfer Length: 256 does not match SCSI CDB Length: 0 for SAM Opcode: 0x12
In that case, the target core adjusts the data_length and sets
se_cmd->residual_count for the underrun. But now suppose that command
fails and we end up in tcm_qla2xxx_queue_status() -- that function
unconditionally overwrites residual_count with the already adjusted
data_length, and the initiator will burp with a message like
qla2xxx [0000:00:06.0]-301d:0: Dropped frame(s) detected (0x100 of 0x100 bytes).
Fix this by adding on to the existing underflow residual count instead.
Signed-off-by: Roland Dreier <roland@purestorage.com>
Cc: Giridhar Malavali <giridhar.malavali@qlogic.com>
Cc: Chad Dupuis <chad.dupuis@qlogic.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Merge 'net' bug fixes into 'net-next' as we have patches
that will build on top of them.
This merge commit includes a change from Emil Goode
(emilgoode@gmail.com) that fixes a warning that would
have been introduced by this merge. Specifically it
fixes the pingv6_ops method ipv6_chk_addr() to add a
"const" to the "struct net_device *dev" argument and
likewise update the dummy_ipv6_chk_addr() declaration.
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the new pci_alloc_dev(bus) to replace the existing using of
alloc_pci_dev(void).
[bhelgaas: drop pci_bus ref later in pci_release_dev()]
Signed-off-by: Gu Zheng <guz.fnst@cn.fujitsu.com>
Signed-off-by: Jiang Liu <jiang.liu@huawei.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: David Airlie <airlied@linux.ie>
Cc: Neela Syam Kolli <megaraidlinux@lsi.com>
Cc: "James E.J. Bottomley" <JBottomley@parallels.com>
Cc: Yinghai Lu <yinghai@kernel.org>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
- Retain firmware defined configuration settings in the absence of
user-provided configuration by eliminating the global RSS and the
PF/VF capabilities mailbox commands.
- Remove S_IRUGO from sysfs parameters that don't have 'show'
functionality.
Signed-off-by: Naresh Kumar Inna <naresh@chelsio.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Resending the patch as it didn't make the linux-scsi list.
This patch fixes fcs rport state machine to address ocassional Brocade
FC Direct Attach LUN discovery failure due to not sending PLOGI accept
to the target.
Signed-off-by: Vijaya Mohan Guvva <vmohan@brocade.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
When a switch disable/enable or a reboot is done, the HBA port gets an
offline and a subsequent online notification. When the port comes up a
link up notification is sent to bfa from the firmware. The bfa then send
an FLOGI to the firmware which is sent out on the wire.
The switch port meanwhile goes offline (presumably for diagnostics)
which causes the switch not to respond to the FLOGI.
The link down notification is sent to the HBA driver. However owing to a
bug in the lps state machine handling the lps state machine does not
move to sm_init state (it remains in sm_login state and send a login
complete message to fcs). This results in a zero PID assignment as the
login is not really complete.
This fix is to correctly handle the events in lps state machine.
Signed-off-by: Vijaya Mohan Guvva <vmohan@brocade.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Introduce eh_timeout which can be used for error handling purposes. This
was previously hardcoded to 10 seconds in the SCSI error handling
code. However, for some fast-fail scenarios it is necessary to be able
to tune this as it can take several iterations (bus device, target, bus,
controller) before we give up.
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
When multipathed systems run into an all-paths-down scenario
all devices might be dropped, too. This causes 'del_gendisk'
to be called, which will unregister the kobj_map->probe()
function for all disk device numbers.
When the device comes back the default ->probe() function
is run which will call __request_module(), which will
deadlock.
As 'del_gendisk' typically does _not_ trigger a module unload
the default ->probe() function is pointless anyway.
This patch implements a dummy ->probe() function, which will
just return NULL if the disk is not registered.
This will avoid the deadlock. Plus it'll speed up device
scanning.
Signed-off-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Defined target_ids,array_ids and vsets_ids as unsigned long to avoid
target_destroy accessing memory after it was freed.
Signed-off-by: Wen Xiong <wenxiong@linux.vnet.ibm.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
If NO_DMA=y:
drivers/built-in.o: In function `ufshcd_transfer_req_compl':
drivers/scsi/ufs/ufshcd.c:1182: undefined reference to `scsi_dma_unmap'
drivers/built-in.o: In function `ufshcd_map_sg':
drivers/scsi/ufs/ufshcd.c:377: undefined reference to `scsi_dma_map'
drivers/built-in.o: In function `ufshcd_do_reset':
drivers/scsi/ufs/ufshcd.c:912: undefined reference to `scsi_dma_unmap'
drivers/built-in.o: In function `ufshcd_memory_alloc':
drivers/scsi/ufs/ufshcd.c:565: undefined reference to `dma_alloc_coherent'
drivers/built-in.o: In function `ufshcd_free_hba_memory':
drivers/scsi/ufs/ufshcd.c:185: undefined reference to `dma_free_coherent'
drivers/scsi/ufs/ufshcd.c:192: undefined reference to `dma_free_coherent'
drivers/scsi/ufs/ufshcd.c:199: undefined reference to `dma_free_coherent'
drivers/scsi/ufs/ufshcd.c:185: undefined reference to `dma_free_coherent'
drivers/scsi/ufs/ufshcd.c:192: undefined reference to `dma_free_coherent'
drivers/built-in.o:drivers/scsi/ufs/ufshcd.c:199: more undefined references to `dma_free_coherent' follow
drivers/built-in.o: In function `ufshcd_abort':
drivers/scsi/ufs/ufshcd.c:1498: undefined reference to `scsi_dma_unmap'
drivers/built-in.o: In function `ufshcd_device_reset':
drivers/scsi/ufs/ufshcd.c:1436: undefined reference to `scsi_dma_unmap'
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Santosh Y <santoshsy@gmail.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Commit 0998d06310 (device-core: Ensure drvdata = NULL when no
driver is bound) removes the need to set driver data field to
NULL.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Santosh Y <santoshsy@gmail.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Coccinelle complains about the inconsistent NULL checking on "t". It
turns out the check isn't needed because we verified that "t" is
non-NULL at the start of the function.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Anand Kumar Santhanam <AnandKumar.Santhanam@pmcs.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Remove the arbitrary expectation in libsas that all SCSI commands are 16 bytes
or less. Instead do all copies via cmd->cmd_len (and use a pointer to this in
the libsas task instead of a copy). Note that this still doesn't enable > 16
byte CDB support in the underlying drivers because their internal format has
to be fixed and the wire format of > 16 byte CDBs according to the SAS spec is
different. the libsas drivers (isci, aic94xx, mvsas and pm8xxx are all
updated for this change.
Cc: Lukasz Dorau <lukasz.dorau@intel.com>
Cc: Maciej Patelczyk <maciej.patelczyk@intel.com>
Cc: Dave Jiang <dave.jiang@intel.com>
Cc: Jack Wang <xjtuwjp@gmail.com>
Cc: Lindar Liu <lindar_liu@usish.com>
Cc: Xiangliang Yu <yuxiangl@marvell.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
The "runtime idle" helper routine, rpm_idle(), currently ignores
return values from .runtime_idle() callbacks executed by it.
However, it turns out that many subsystems use
pm_generic_runtime_idle() which checks the return value of the
driver's callback and executes pm_runtime_suspend() for the device
unless that value is not 0. If that logic is moved to rpm_idle()
instead, pm_generic_runtime_idle() can be dropped and its users
will not need any .runtime_idle() callbacks any more.
Moreover, the PCI, SCSI, and SATA subsystems' .runtime_idle()
routines, pci_pm_runtime_idle(), scsi_runtime_idle(), and
ata_port_runtime_idle(), respectively, as well as a few drivers'
ones may be simplified if rpm_idle() calls rpm_suspend() after 0 has
been returned by the .runtime_idle() callback executed by it.
To reduce overall code bloat, make the changes described above.
Tested-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Tested-by: Kevin Hilman <khilman@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Kevin Hilman <khilman@linaro.org>
Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
The 'ctl' field of the 'struct ata_taskfile' is not really dual purpose, i.e.
it is not intended for storing the alternate status register (which is mapped
at the same address in the legacy IDE controllers) in the qc_fill_rtf() method.
No other 'libata' driver except 'drivers/scsi/ipr.c' stores the alternate status
register's value in the 'ctl' field of 'qc->result_tf', hence this driver should
not do this as well...
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Acked-by: Brian King <brking@linux.vnet.ibm.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Pull scsi target fixes from Nicholas Bellinger:
"The highlights include:
- Re-instate sess->wait_list in target_wait_for_sess_cmds() for
active I/O shutdown handling in fabrics using se_cmd->cmd_kref
- Make ib_srpt call target_sess_cmd_list_set_waiting() during session
shutdown
- Fix FILEIO off-by-one READ_CAPACITY bug for !S_ISBLK export
- Fix iscsi-target login error heap buffer overflow (Kees)
- Fix iscsi-target active I/O shutdown handling regression in
v3.10-rc1
A big thanks to Kees Cook for fixing a long standing login error
buffer overflow bug.
All patches are CC'ed to stable with the exception of the v3.10-rc1
specific regression + other minor target cleanup."
* git://git.kernel.org/pub/scm/linux/kernel/git/nab/target-pending:
iscsi-target: Fix iscsit_free_cmd() se_cmd->cmd_kref shutdown handling
target: Propigate up ->cmd_kref put return via transport_generic_free_cmd
iscsi-target: fix heap buffer overflow on error
target/file: Fix off-by-one READ_CAPACITY bug for !S_ISBLK export
ib_srpt: Call target_sess_cmd_list_set_waiting during shutdown_session
target: Re-instate sess_wait_list for target_wait_for_sess_cmds
target: Remove unused wait_for_tasks bit in target_wait_for_sess_cmds
That patch failed to set proc_scsi_fops' .release method.
Signed-off-by: Jan Beulich <jbeulich@suse.com>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
So far, only net_device * could be passed along with netdevice notifier
event. This patch provides a possibility to pass custom structure
able to provide info that event listener needs to know.
Signed-off-by: Jiri Pirko <jiri@resnulli.us>
v2->v3: fix typo on simeth
shortened dev_getter
shortened notifier_info struct name
v1->v2: fix notifier_call parameter in call_netdevice_notifier()
Signed-off-by: David S. Miller <davem@davemloft.net>
Drop unused transport_wait_for_tasks() check in target_wait_for_sess_cmds
shutdown code, and convert tcm_qla2xxx + ib_srpt fabric drivers.
Cc: Joern Engel <joern@logfs.org>
Cc: Roland Dreier <roland@kernel.org>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Defined target_ids,array_ids and vsets_ids as unsigned long to avoid
target_destroy accessing memory after it was freed.
Signed-off-by: Wen Xiong <wenxiong@linux.vnet.ibm.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
The driver uses ha->mbx_cmd_flags variable to pass information between
its ISR and mailbox routines, however, it does so without the protection of
any locks. Under certain conditions, this can lead to multiple mailbox
command completions being signaled, which, in turn, leads to a false
mailbox timeout error for the subsequently issued mailbox command.
The issue occurs frequently but intermittenly with the Qlogic 8GFC mezz
card during card initialization, resulting in card initialization failure.
Signed-off-by: Gurinder (Sunny) Shergill <gurinder.shergill@hp.com>
Acked-by: Saurav Kashyap <saurav.kashyap@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
This warning was reported recently:
WARNING: at drivers/scsi/libfc/fc_exch.c:478 fc_seq_send+0x14f/0x160 [libfc]()
(Not tainted)
Hardware name: ProLiant DL120 G7
Modules linked in: tcm_fc target_core_iblock target_core_file target_core_pscsi
target_core_mod configfs dm_round_robin dm_multipath 8021q garp stp llc bnx2fc
cnic uio fcoe libfcoe libfc scsi_transport_fc scsi_tgt autofs4 sunrpc
pcc_cpufreq ipv6 hpilo hpwdt e1000e microcode iTCO_wdt iTCO_vendor_support
serio_raw shpchp ixgbe dca mdio sg ext4 mbcache jbd2 sd_mod crc_t10dif pata_acpi
ata_generic ata_piix hpsa dm_mirror dm_region_hash dm_log dm_mod [last unloaded:
scsi_wait_scan]
Pid: 5464, comm: target_completi Not tainted 2.6.32-272.el6.x86_64 #1
Call Trace:
[<ffffffff8106b747>] ? warn_slowpath_common+0x87/0xc0
[<ffffffff8106b79a>] ? warn_slowpath_null+0x1a/0x20
[<ffffffffa025f7df>] ? fc_seq_send+0x14f/0x160 [libfc]
[<ffffffffa035cbce>] ? ft_queue_status+0x16e/0x210 [tcm_fc]
[<ffffffffa030a660>] ? target_complete_ok_work+0x0/0x4b0 [target_core_mod]
[<ffffffffa030a766>] ? target_complete_ok_work+0x106/0x4b0 [target_core_mod]
[<ffffffffa030a660>] ? target_complete_ok_work+0x0/0x4b0 [target_core_mod]
[<ffffffff8108c760>] ? worker_thread+0x170/0x2a0
[<ffffffff810920d0>] ? autoremove_wake_function+0x0/0x40
[<ffffffff8108c5f0>] ? worker_thread+0x0/0x2a0
[<ffffffff81091d66>] ? kthread+0x96/0xa0
[<ffffffff8100c14a>] ? child_rip+0xa/0x20
[<ffffffff81091cd0>] ? kthread+0x0/0xa0
[<ffffffff8100c140>] ? child_rip+0x0/0x20
It occurs because fc_seq_send can have multiple contexts executing within it at
the same time, and fc_seq_send doesn't consistently use the ep->ex_lock that
protects this structure. Because of that, its possible for one context to clear
the INIT bit in the ep->esb_state field while another checks it, leading to the
above stack trace generated by the WARN_ON in the function.
We should probably undertake the effort to convert access to the fc_exch
structures to use rcu, but that a larger work item. To just fix this specific
issue, we can just extend the ex_lock protection through the entire fc_seq_send
path
Signed-off-by: Neil Horman <nhorman@tuxdriver.com>
Reported-by: Gris Ge <fge@redhat.com>
CC: Robert Love <robert.w.love@intel.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
The service_params field is being checked against the symbol
FC_RPORT_ROLE_FCP_INITIATOR where it really should be checked
against FCP_SPPF_INIT_FCN.
Signed-off-by: Mark Rustad <mark.d.rustad@intel.com>
Tested-by: Jack Morgan <jack.morgan@intel.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
When multiple FCFs in use, and first FIP Advertisement received is
with "Available for Login" i.e A bit set to 0, FCF selection will fail.
The fix is to remove the assumption in the code that first FCF is only
allowed selectable FCF.
Consider the scenario fip->fcfs contains FCF1(fabricname X, marked A=0)
FCF2(fabricname Y, marked A=1). list_first_entry(first) points to FCF1
and 1st iteration we ignore the FCF and on 2nd iteration we compare
FCF1 & FCF2 fabric name and we fails to perform FCF selection.
Signed-off-by: Krishna Mohan <krmohan@cisco.com>
Reviewed-by: Bhanu Prakash Gollapudi <bprakash@broadcom.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
This fixes a bug where the iscsi class/driver did not do a put_device
when a sess/conn device was found. This also simplifies the interface
by not having to pass in some arguments that were duplicated and did
not need to be exported.
Reported-by: Zhao Hongjiang <zhaohongjiang@huawei.com>
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Acked-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
These enums have been separate since the dawn of SAS, mainly because the
latter is a procotol only enum and the former includes additional state
for libsas. The dichotomy causes endless confusion about which one you
should use where and leads to pointless warnings like this:
drivers/scsi/mvsas/mv_sas.c: In function 'mvs_update_phyinfo':
drivers/scsi/mvsas/mv_sas.c:1162:34: warning: comparison between 'enum sas_device_type' and 'enum sas_dev_type' [-Wenum-compare]
Fix by eliminating one of them. The one kept is effectively the sas.h
one, but call it sas_device_type and make sure the enums are all
properly namespaced with the SAS_ prefix.
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Modified thermal configuration to happen after interrupt registration
Added SAS controller configuration during initialization
Added error handling logic to handle I_T_Nexus errors and variants
[jejb: fix up tabs and spaces issues]
Signed-off-by: Anand Kumar S <AnandKumar.Santhanam@pmcs.com>
Acked-by: Jack Wang <jack_wang@usish.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Handled NCQ errors in the low level driver as the FW
is not providing the faulty tag for NCQ errors for libsas
to recover.
[jejb: fix checkpatch issues]
Signed-off-by: Anand Kumar S <AnandKumar.Santhanam@pmcs.com>
Acked-by: Jack Wang <jack_wang@usish.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Individual WWN read operations based on controller.
PM8081 - Read WWN from Flash VPD.
PM8088/89 - Read WWN from EEPROM.
PM8001 - Read WWN from NVM.
Signed-off-by: Sakthivel K <Sakthivel.SaravananKamalRaju@pmcs.com>
Signed-off-by: Anand Kumar S <AnandKumar.Santhanam@pmcs.com>
Acked-by: Jack Wang <jack_wang@usish.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Changed name in driver to pm80xx. Updated debug messages.
Signed-off-by: Sakthivel K <Sakthivel.SaravananKamalRaju@pmcs.com>
Signed-off-by: Anand Kumar S <AnandKumar.Santhanam@pmcs.com>
Acked-by: Jack Wang <jack_wang@usish.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Performing pci_free_consistent in tasklet had result in a core dump. So
allocated a new memory region for it. Fix for passing proper address
and operation in firmware flash update.
Signed-off-by: Sakthivel K <Sakthivel.SaravananKamalRaju@pmcs.com>
Signed-off-by: Anand Kumar S <AnandKumar.Santhanam@pmcs.com>
Acked-by: Jack Wang <jack_wang@usish.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Additional bar shift for new SPC firmware, applicable to device
id 0x8081 only.
Signed-off-by: Sakthivel K <Sakthivel.SaravananKamalRaju@pmcs.com>
Signed-off-by: Anand Kumar S <AnandKumar.Santhanam@pmcs.com>
Acked-by: Jack Wang <jack_wang@usish.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Implementation of SPCv/ve specific hardware functionality and
macros. Changing common functionalities wrt SPCv/ve operations.
Conditional checks for SPC specific operations.
Signed-off-by: Sakthivel K <Sakthivel.SaravananKamalRaju@pmcs.com>
Signed-off-by: Anand Kumar S <AnandKumar.Santhanam@pmcs.com>
Acked-by: Jack Wang <jack_wang@usish.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Implementation of interrupt handlers and tasklets to support
upto 64 interrupt for the device.
Signed-off-by: Sakthivel K <Sakthivel.SaravananKamalRaju@pmcs.com>
Signed-off-by: Anand Kumar S <AnandKumar.Santhanam@pmcs.com>
Acked-by: Jack Wang <jack_wang@usish.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Update of function prototype for common function to SPC and SPCv/ve.
Multiple queues implementation for IO.
Signed-off-by: Sakthivel K <Sakthivel.SaravananKamalRaju@pmcs.com>
Signed-off-by: Anand Kumar S <AnandKumar.Santhanam@pmcs.com>
Acked-by: Jack Wang <jack_wang@usish.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Memory allocation and configuration of multiple inbound and
outbound queues.
Signed-off-by: Sakthivel K <Sakthivel.SaravananKamalRaju@pmcs.com>
Signed-off-by: Anand Kumar S <AnandKumar.Santhanam@pmcs.com>
Acked-by: Jack Wang <jack_wang@usish.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Updated pci id table with device, vendor, subdevice and subvendor ids
for 8081, 8088, 8089 SAS/SATA controllers. Added SPCv/ve related macros.
Updated macros, hba info structure and other structures for SPCv/ve.
Update of structure and variable names for SPC hardware functionalities.
Signed-off-by: Sakthivel K <Sakthivel.SaravananKamalRaju@pmcs.com>
Signed-off-by: Anand Kumar S <AnandKumar.Santhanam@pmcs.com>
Acked-by: Jack Wang <jack_wang@usish.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
lpfc uses the generic checksum as well as the T10DIF one from the lib/
directory, so make sure they're selected.
Reported-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
scsi_send_eh_cmnd() is calling queuecommand() directly, so
it needs to check the return value here.
The only valid return codes for queuecommand() are 'busy'
states, so we need to wait for a bit to allow the LLDD
to recover.
Based on an earlier patch from Wen Xiong.
[jejb: fix confusion between msec and jiffies values and other issues]
[bvanassche: correct stall_for interval]
Cc: Wen Xiong <wenxiong@linux.vnet.ibm.com>
Cc: Brian King <brking@linux.vnet.ibm.com>
Signed-off-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Pull block core updates from Jens Axboe:
- Major bit is Kents prep work for immutable bio vecs.
- Stable candidate fix for a scheduling-while-atomic in the queue
bypass operation.
- Fix for the hang on exceeded rq->datalen 32-bit unsigned when merging
discard bios.
- Tejuns changes to convert the writeback thread pool to the generic
workqueue mechanism.
- Runtime PM framework, SCSI patches exists on top of these in James'
tree.
- A few random fixes.
* 'for-3.10/core' of git://git.kernel.dk/linux-block: (40 commits)
relay: move remove_buf_file inside relay_close_buf
partitions/efi.c: replace useless kzalloc's by kmalloc's
fs/block_dev.c: fix iov_shorten() criteria in blkdev_aio_read()
block: fix max discard sectors limit
blkcg: fix "scheduling while atomic" in blk_queue_bypass_start
Documentation: cfq-iosched: update documentation help for cfq tunables
writeback: expose the bdi_wq workqueue
writeback: replace custom worker pool implementation with unbound workqueue
writeback: remove unused bdi_pending_list
aoe: Fix unitialized var usage
bio-integrity: Add explicit field for owner of bip_buf
block: Add an explicit bio flag for bios that own their bvec
block: Add bio_alloc_pages()
block: Convert some code to bio_for_each_segment_all()
block: Add bio_for_each_segment_all()
bounce: Refactor __blk_queue_bounce to not use bi_io_vec
raid1: use bio_copy_data()
pktcdvd: Use bio_reset() in disabled code to kill bi_idx usage
pktcdvd: use bio_copy_data()
block: Add bio_copy_data()
...
Merge more incoming from Andrew Morton:
- Various fixes which were stalled or which I picked up recently
- A large rotorooting of the AIO code. Allegedly to improve
performance but I don't really have good performance numbers (I might
have lost the email) and I can't raise Kent today. I held this out
of 3.9 and we could give it another cycle if it's all too late/scary.
I ended up taking only the first two thirds of the AIO rotorooting. I
left the percpu parts and the batch completion for later. - Linus
* emailed patches from Andrew Morton <akpm@linux-foundation.org>: (33 commits)
aio: don't include aio.h in sched.h
aio: kill ki_retry
aio: kill ki_key
aio: give shared kioctx fields their own cachelines
aio: kill struct aio_ring_info
aio: kill batch allocation
aio: change reqs_active to include unreaped completions
aio: use cancellation list lazily
aio: use flush_dcache_page()
aio: make aio_read_evt() more efficient, convert to hrtimers
wait: add wait_event_hrtimeout()
aio: refcounting cleanup
aio: make aio_put_req() lockless
aio: do fget() after aio_get_req()
aio: dprintk() -> pr_debug()
aio: move private stuff out of aio.h
aio: add kiocb_cancel()
aio: kill return value of aio_complete()
char: add aio_{read,write} to /dev/{null,zero}
aio: remove retry-based AIO
...
The value passed is 0 in all but "it can never happen" cases (and those
only in a couple of drivers) *and* it would've been lost on the way
out anyway, even if something tried to pass something meaningful.
Just don't bother.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Uses block layer runtime pm helper functions in
scsi_runtime_suspend/resume for devices that take advantage of it.
Remove scsi_autopm_* from sd open/release path and check_events path.
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Aaron Lu <aaron.lu@intel.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
With the introduction of REQ_PM, modify sd's runtime suspend operation
functions to use that flag so that the operations to put the device into
runtime suspended state(i.e. sync cache and stop device) will not affect
its runtime PM status.
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Aaron Lu <aaron.lu@intel.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
This patch corrects the expected data transfer size of the
command UPIU. The current implementation of cmd->transfersize
is wrong as it probably equal to sector size. With this
implementation the transfer size is updated correctly
Reported-by: KOBAYASHI Yoshitake <yoshitake.kobayashi@toshiba.co.jp>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Namjae Jeon <linkinjeon@gmail.com>
Reviewed-by: Subhash Jadavani <subhashj@codeaurora.org>
Tested-by: Maya Erez <merez@codeaurora.org>
Signed-off-by: Santosh Yaraganavi <santoshsy@gmail.com>
Signed-off-by: Vinayak Holikatti <vinholikatti@gmail.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Some arrays synchronize their full non volatile cache when the sd driver sends
a SYNCHRONIZE CACHE command. Unfortunately, they can have Terrabytes of this
and we send a SYNCHRONIZE CACHE for every barrier if an array reports it has a
writeback cache. This leads to massive slowdowns on journalled filesystems.
The fix is to allow userspace to turn off the writeback cache setting as a
temporary measure (i.e. without doing the MODE SELECT to write it back to the
device), so even though the device reported it has a writeback cache, the
user, knowing that the cache is non volatile and all they care about is
filesystem correctness, can turn that bit off in the kernel and avoid the
performance ruinous (and safety irrelevant) SYNCHRONIZE CACHE commands.
The way you do this is add a 'temporary' prefix when performing the usual
cache setting operations, so
echo temporary write through > /sys/class/scsi_disk/<disk>/cache_type
Reported-by: Ric Wheeler <rwheeler@redhat.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Found by 0 day test project
Reported-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: Armen Baloyan <armen.baloyan@qlogic.com>
Signed-off-by: Saurav Kashyap <saurav.kashyap@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
provisioning map (map_storep) is a bitmap accessed by bitops.
So the allocation size should be a multiple of sizeof(unsigned long) and
also the bitmap should be cleared by using bitmap_clear() instead of
memset().
Otherwise it will cause problem on big-endian architecture if the number of
bits is not a multiple of BITS_PER_LONG.
I tried testing the logical block provisioning support in scsi_debug,
but it didn't work as I expected.
For example, load scsi_debug module with UNMAP command supported
and fill the storage with random data.
# modprobe scsi_debug lbpu=1
# dd if=/dev/urandom of=/dev/sdb
Then, try to unmap LBA 0, but Get LBA status reports:
# sg_unmap --lba=0 --num=1 /dev/sdb
# sg_get_lba_status --lba=0 /dev/sdb
descriptor LBA: 0x0000000000000000 blocks: 16384 mapped
This is unexpected result. Because UNMAP command to LBA 0 finished
without any errors, but Get LBA status shows that LBA 0 is still mapped.
This problem is due to the wrong translation between LBA and index of
provisioning map. Fix it by using correct translation functions.
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Acked-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
The function unmap_region() clears memory region specified as the logical
block address and the number of logical blocks in ramdisk storage
(fake_storep) if lbpu and lbprz module parameters are enabled.
In the while loop of unmap_region(), it advances optimal unmap granularity
in logical blocks. But it only clears one logical block at LBA 'block' per
loop iteration. And furthermore, the 'block' is not pointing to a logical
block address which should be cleared, it is a index of probisioning map
(map_storep).
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Acked-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
scsi_debug prohibits setting scsi_debug_unmap_alignment to be greater
than scsi_debug_unmap_granularity. But setting them to be the same value
is not prohibited. In this case, the only difference with
scsi_debug_unmap_alignment == 0 is the logical blocks from 0 to
scsi_debug_unmap_alignment - 1 cannot be unmapped. But the difference is
not properly handled in the current code.
So this prohibits such unusual setting.
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Acked-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
If the logical block provisioning is not enabled, map_region() and
unmap_region() have no effect and they don't need to be called.
So this makes map_region() and unmap_region() to be called only
when scsi_debug_lbp() returns true, i.e. logical block provisioning is
enabled.
While I'm at it, this also removes meaningless non-zero check for
scsi_debug_unmap_granularity.
Because scsi_debug_unmap_granularity cannot be zero with usual setting:
scsi_debug_unmap_granularity is 1 by default, and it can be changed to
zero with explicit module parameter setting only when the logical block
provisioning is disabled. But it is only meaningful module parameter
when the logical block provisioning is enabled.
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Acked-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
It appears to me that there is a problem with handling of type 1 protection
information.
It is considering a logical block reference tag of 0xffffffff to be an error,
but it is actually valid any time ((lba & 0xffffffff) == 0xffffffff) [for
example, 2TiB-1, 4TiB-1, 6TiB-1, etc.].
I'm going by what's written in 4.18.3 of SBC3, where there doesn't appear
to be any invalid value for the reference tag.
Signed-off-by: Jeremy Higdon <jeremy@sgi.com>
Acked-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Driver passed the wrong IOADL address to IOA adapter. The patch
fixes the issue.
Signed-off-by: Wen Xiong <wenxiong@linux.vnet.ibm.com>
Acked-by: Brian King <brking@linux.vnet.ibm.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Fix to return -ENOMEM in the create workqueue error case
instead of 0, as done elsewhere in this function.
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
I dived into lguest again, reworking the pagetable code so we can move
the switcher page: our fixmaps sometimes take more than 2MB now...
Cheers,
Rusty.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=1tYL
-----END PGP SIGNATURE-----
Merge tag 'virtio-next-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rusty/linux
Pull virtio & lguest updates from Rusty Russell:
"Lots of virtio work which wasn't quite ready for last merge window.
Plus I dived into lguest again, reworking the pagetable code so we can
move the switcher page: our fixmaps sometimes take more than 2MB now..."
Ugh. Annoying conflicts with the tcm_vhost -> vhost_scsi rename.
Hopefully correctly resolved.
* tag 'virtio-next-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rusty/linux: (57 commits)
caif_virtio: Remove bouncing email addresses
lguest: improve code readability in lg_cpu_start.
virtio-net: fill only rx queues which are being used
lguest: map Switcher below fixmap.
lguest: cache last cpu we ran on.
lguest: map Switcher text whenever we allocate a new pagetable.
lguest: don't share Switcher PTE pages between guests.
lguest: expost switcher_pages array (as lg_switcher_pages).
lguest: extract shadow PTE walking / allocating.
lguest: make check_gpte et. al return bool.
lguest: assume Switcher text is a single page.
lguest: rename switcher_page to switcher_pages.
lguest: remove RESERVE_MEM constant.
lguest: check vaddr not pgd for Switcher protection.
lguest: prepare to make SWITCHER_ADDR a variable.
virtio: console: replace EMFILE with EBUSY for already-open port
virtio-scsi: reset virtqueue affinity when doing cpu hotplug
virtio-scsi: introduce multiqueue support
virtio-scsi: push vq lock/unlock into virtscsi_vq_done
virtio-scsi: pass struct virtio_scsi to virtqueue completion function
...
Add reset adapter after the 6th EEH errors in ipr driver. This triggers
the adapter reset via the PCI config space even when the slot is frozen.
Signed-off-by: Wen Xiong <wenxiong@linux.vnet.ibm.com>
Acked-by: Brian King <brking@linux.vnet.ibm.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Assign values using correct datatype in function qla4xxx_copy_to_fwddb_param()
Signed-off-by: Adheer Chandravanshi <adheer.chandravanshi@qlogic.com>
Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Fix following warning:
drivers/scsi/qla4xxx/ql4_os.c:5507:5:
warning: symbol 'qla4xxx_sysfs_ddb_tgt_create' was not declared. Should it be
static?
Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Fix followig gcc warning:-
drivers/scsi/qla4xxx/ql4_os.c: In function ‘qla4xxx_sysfs_ddb_get_param’:
drivers/scsi/qla4xxx/ql4_os.c:6279:
warning: comparison is always true due to limited range of data type
drivers/scsi/qla4xxx/ql4_os.c:6290:
warning: comparison is always true due to limited range of data type
drivers/scsi/qla4xxx/ql4_os.c: In function ‘qla4xxx_sysfs_ddb_delete’:
drivers/scsi/qla4xxx/ql4_os.c:6593:
warning: ‘ddb_size’ may be used uninitialized in this function
Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
We should unlock here before returning.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Adam Radford <aradford@gmail.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Signed-off-by: Brian King <brking@linux.vnet.ibm.com>
Acked-by: Robert Jennings <rcj@linux.vnet.ibm.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Adds support for a new VIOS feature that allows ibmvfc to
optimize terminate_rport_io by telling the VIOS the target
is no longer accessible on the fabric and that it should
not send an ABTS out on the fabric to the device.
Signed-off-by: Brian King <brking@linux.vnet.ibm.com>
Acked-by: Robert Jennings <rcj@linux.vnet.ibm.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
If attempting to abort requests due to a fail fail timeout
or error handling while the link is down, we cannot send
an abort out on the fabric. We can, however, send a cancel
to the VIOS. This fixes ibmvfc to send a cancel in this
case to prevent error handling from failing and/or
escalating.
Signed-off-by: Brian King <brking@linux.vnet.ibm.com>
Acked-by: Robert Jennings <rcj@linux.vnet.ibm.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Adds support for receiving FAST_IO_FAIL from fc_block_scsi_eh
when in error recovery. This fixes cases of devices being
taken offline when they are no longer accessible on the fabric,
preventing them from coming back online when the fabric recovers.
Signed-off-by: Brian King <brking@linux.vnet.ibm.com>
Acked-by: Robert Jennings <rcj@linux.vnet.ibm.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
The flags on a cancel operation are intended to indicate what,
if any, TMF will follow the cancel request. This fixes a case
where we were incorrectly setting the abort task set flag on
the cancel flag when we were cancelling an abort task set.
Signed-off-by: Brian King <brking@linux.vnet.ibm.com>
Acked-by: Robert Jennings <rcj@linux.vnet.ibm.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Signed-off-by: John Soni Jose <sony.john-n@emulex.com>
Signed-off-by: Jayamohan Kallickal <jayamohan.kallickal@emulex.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Command Window value from the CQE was used to calculate the
max_cmdsn for that session.The command window value extracted
for SKH-R adapter was not proper. The value was extracted from
BE adapter completion event. Fixed the issue by getting the
cmd_wnd value from SKH-R CQE.
The exp_cmdsn and max_cmdsn values were not converted to BE format
before calling the __iscsi_complete_pdu(). Fixed the issue of converting
to BE format.
Signed-off-by: John Soni Jose <sony.john-n@emulex.com>
Signed-off-by: Jayamohan Kallickal <jayamohan.kallickal@emulex.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
The driver creates "NAPI" context per core which is fine,
however the above routine declares the ret variable as static!
Thus there is only one instance of this variable!
When this routine is called from more than one thread of execution,
than the result is unpredictable.
static unsigned int ret;
.....
ret = beiscsi_process_cq(pbe_eq);
<--------Another thread can enter here and change "ret".
if (ret < budget) {
....
}
<--------Another thread can enter here and change "ret".
return ret;
Fix - remove the "static"
Signed-off-by: Shlomo Pongratz <shlomop@mellanox.com>
Signed-off-by: Jayamohan Kallickal <jayamohan.kallickal@emulex.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Signed-off-by: John Soni Jose <sony.john-n@emulex.com>
Signed-off-by: Jayamohan Kallickal <jayamohan.kallickal@emulex.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Before tyring to establish a CXN with the target, check if the adapter is in
a stable state
Signed-off-by: John Soni Jose <sony.john-n@emulex.com>
Signed-off-by: Jayamohan Kallickal <jayamohan.kallickal@emulex.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Number of CID assigned to a function from adapter can be dynamic. The CID count
for each function was fixed number before. Code Fix done so that adapters with
fixed/dynamic CID count will work with the driver.
Signed-off-by: John Soni Jose <sony.john-n@emulex.com>
Signed-off-by: Jayamohan Kallickal <jayamohan.kallickal@emulex.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
When target send a NOP-IN with valid TTT, driver issues a NOP-OUT
and the task was not freed from driver. The task list available for
the session used to run out, and as no more task list were available
no more iSCSI commands were exchanged on that session.
This patches fixed the issue, by calling iscsi_put_task.
Signed-off-by: Minh Tran <minhduc.tran@emulex.com>
Signed-off-by: John Soni Jose <sony.john-n@emulex.com>
Signed-off-by: Jayamohan Kallickal <jayamohan.kallickal@emulex.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Check the Logical Link status also as part of the port link status.
Signed-off-by: John Soni Jose <sony.john-n@emulex.com>
Signed-off-by: Jayamohan Kallickal <jayamohan.kallickal@emulex.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
This patch fixes the displaying of number of active
sessions in use.
Signed-off-by: John Soni Jose <sony.john-n@emulex.com>
Signed-off-by: Jayamohan Kallickal <jayamohan.kallickal@emulex.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
The mgmt_hba_attributes structure declared was not proper and
because of that the FW response returned for the MBX_CMD was not
matching. This issue went unnoticed as mgmt_hba_attribs structure
members were never used in the code path.
This fix of displaying the FW version had to change the mgmt_hba_attrib
structure also. The latest driver will also work with the older FW as
the issue was in the driver declaration.
Signed-off-by: John Soni Jose <sony.john-n@emulex.com>
Signed-off-by: Jayamohan Kallickal <jayamohan.kallickal@emulex.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Fix support for DEFQ extension which will be used by latest
adapters
Signed-off-by: John Soni Jose <sony.john-n@emulex.com>
Signed-off-by: Jayamohan Kallickal <jayamohan.kallickal@emulex.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Fixed the code flow based on the MACRO defined to check for
adapter.
Signed-off-by: John Soni Jose <sony.john-n@emulex.com>
Signed-off-by: Jayamohan Kallickal <jayamohan.kallickal@emulex.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Free CXN specific resource held by driver when login redirection
or connection retry happens. Login redirection was failing
because WRB/SGL were not allocated from the CID on which
doorbell was rung.
Fixed the issue raised by MikeC
Signed-off-by: John Soni Jose <sony.john-n@emulex.com>
Signed-off-by: Jayamohan Kallickal <jayamohan.kallickal@emulex.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
This patch limits the max number of msix vectors to 32.
Signed-off-by: John Soni Jose <sony.john-n@emulex.com>
Signed-off-by: Jayamohan Kallickal <jayamohan.kallickal@emulex.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
- Check Ready Bit before posting the BMBX Hi Address
- Fix the parameters passed to beiscsi_mccq_compl
in beiscsi_open_conn()
- Fix tag value check in beiscsi_ep_connect.
Signed-off-by: John Soni Jose <sony.john-n@emulex.com>
Signed-off-by: Jayamohan Kallickal <jayamohan.kallickal@emulex.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
When MBX command fails with insufficent buffer, check for the
response lenght returned. Return success if response length
is non-zero value which indicates valid data.
Signed-off-by: Minh Tran <minhduc.tran@emulex.com>
Signed-off-by: John Soni Jose <sony.john-n@emulex.com>
Signed-off-by: Jayamohan Kallickal <jayamohan.kallickal@emulex.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
This patch sends uninitialize pattern to FW during driver unload
which is expected by FW for cleanup
Signed-off-by: John Soni Jose <sony.john-n@emulex.com>
Signed-off-by: Jayamohan Kallickal <jayamohan.kallickal@emulex.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
We need to store PROTO_ERR_IMPL_LOGO (26) things here, but the
first element isn't used so the array should have 27 elements.
This matches fwevt_to_rnevt[] which has 27 elements.
The patch solves a Smatch static checker warning on my system:
drivers/scsi/csiostor/csio_rnode.c:880 csio_rnode_fwevt_handler()
error: buffer overflow '(rn)->stats.n_evt_fw' 26 <= 26
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Naresh Kumar Inna <naresh@chelsio.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
When IO is successfully completed while an abort is pending, eh_abort
incorrectly assumes that abort failed and performes recovery by issuing
cleanup. Howerver, cleanup timesout as the firmware has no clue about
this IO. Fix this by checking if the IO has already completed.
Signed-off-by: Bhanu Prakash Gollapudi <bprakash@broadcom.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Set perf_config to 3 during firmware initialization to enable both
cached connections as well as cached tasks.
Signed-off-by: Bhanu Prakash Gollapudi <bprakash@broadcom.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
If switch configured in FIP and adapter configured in non-fip mode, driver
panics while queueing FIP frame in non-existing fip_frame_queue. Added config
check before queueing FIP frame in misconfiguration case to avoid kernel panic.
Signed-off-by: Hiral Patel <hiralpat@cisco.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
FIP VLAN discovery discovers the FCoE VLAN that will be used by all other FIP
protocols as well as by the FCoE encapsulation for Fibre Channel payloads on
the established virtual link. One of the goals of FC-BB-5 was to be as
nonintrusive as possible on initiators and targets, and therefore FIP VLAN
discovery occurs in the native VLAN used by the initiator or target to
exchange Ethernet traffic. The FIP VLAN discovery protocol is the only FIP
protocol running on the native VLAN; all other FIP protocols run on the
discovered FCoE VLANs.
If an administrator has manually configured FCoE VLANs on ENodes and FCFs,
there is no need to use this protocol. FIP and FCoE will run over the
configured VLANs.
An ENode without FCoE VLANs configuration would use this automated discovery
protocol to discover over which VLANs FCoE is running.
The ENode sends a FIP VLAN discovery request to a multicast MAC address called
All-FCF-MACs, which is a multicast MAC address to which all FCFs listen.
All FCFs that can be reached in the native VLAN of the ENode are expected to
respond on the same VLAN with a response that lists one or more FCoE VLANs
that are available for the ENode's VN_Port login. This protocol has the sole
purpose of allowing the ENode to discover all the available FCoE VLANs.
Now the ENode may enable a subset of these VLANs for FCoE Running the FIP
protocol in these VLANs on a per VLAN basis. And FCoE data transactions also
would occur on this VLAN. Hence, Except for FIP VLAN discovery, all other FIP
and FCoE traffic runs on the selected FCoE VLAN. Its only the FIP VLAN
Discovery protocol that is permitted to run on the Default native VLAN of the
system.
[**** NOTE ****]
We are working on moving this feature definitions and functionality to libfcoe
module. We need this patch to be approved, as Suse is looking forward to merge
this feature in SLES 11 SP3 release. Once this patch is approved, we will
submit patch which should move vlan discovery feature to libfoce.
[Fengguang Wu <fengguang.wu@intel.com>: kmalloc cast removal]
Signed-off-by: Anantha Prakash T <atungara@cisco.com>
Signed-off-by: Hiral Patel <hiralpat@cisco.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Pull VFS updates from Al Viro,
Misc cleanups all over the place, mainly wrt /proc interfaces (switch
create_proc_entry to proc_create(), get rid of the deprecated
create_proc_read_entry() in favor of using proc_create_data() and
seq_file etc).
7kloc removed.
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs: (204 commits)
don't bother with deferred freeing of fdtables
proc: Move non-public stuff from linux/proc_fs.h to fs/proc/internal.h
proc: Make the PROC_I() and PDE() macros internal to procfs
proc: Supply a function to remove a proc entry by PDE
take cgroup_open() and cpuset_open() to fs/proc/base.c
ppc: Clean up scanlog
ppc: Clean up rtas_flash driver somewhat
hostap: proc: Use remove_proc_subtree()
drm: proc: Use remove_proc_subtree()
drm: proc: Use minor->index to label things, not PDE->name
drm: Constify drm_proc_list[]
zoran: Don't print proc_dir_entry data in debug
reiserfs: Don't access the proc_dir_entry in r_open(), r_start() r_show()
proc: Supply an accessor for getting the data from a PDE's parent
airo: Use remove_proc_subtree()
rtl8192u: Don't need to save device proc dir PDE
rtl8187se: Use a dir under /proc/net/r8180/
proc: Add proc_mkdir_data()
proc: Move some bits from linux/proc_fs.h to linux/{of.h,signal.h,tty.h}
proc: Move PDE_NET() to fs/proc/proc_net.c
...
Supply an accessor function for getting the private data from the parent
proc_dir_entry struct of the proc_dir_entry struct associated with an inode.
ReiserFS, for instance, stores the super_block pointer in the proc directory
it makes for that super_block, and a pointer to the respective seq_file show
function in each of the proc files in that directory.
This allows a reduction in the number of file_operations structs, open
functions and seq_operations structs required. The problem otherwise is that
each show function requires two pieces of data but only has storage for one
per PDE (and this has no release function).
Signed-off-by: David Howells <dhowells@redhat.com>
Acked-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
cc: Jerry Chuang <jerry-chuang@realtek.com>
cc: Maxim Mikityanskiy <maxtram95@gmail.com>
cc: YAMANE Toshiaki <yamanetoshi@gmail.com>
cc: linux-wireless@vger.kernel.org
cc: linux-scsi@vger.kernel.org
cc: devel@driverdev.osuosl.org
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Add proc_mkdir_data() to allow procfs directories to be created that are
annotated at the time of creation with private data rather than doing this
post-creation. This means no access is then required to the proc_dir_entry
struct to set this.
Signed-off-by: David Howells <dhowells@redhat.com>
Acked-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
cc: Neela Syam Kolli <megaraidlinux@lsi.com>
cc: Jerry Chuang <jerry-chuang@realtek.com>
cc: linux-scsi@vger.kernel.org
cc: devel@driverdev.osuosl.org
cc: linux-wireless@vger.kernel.org
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Pull networking updates from David Miller:
"Highlights (1721 non-merge commits, this has to be a record of some
sort):
1) Add 'random' mode to team driver, from Jiri Pirko and Eric
Dumazet.
2) Make it so that any driver that supports configuration of multiple
MAC addresses can provide the forwarding database add and del
calls by providing a default implementation and hooking that up if
the driver doesn't have an explicit set of handlers. From Vlad
Yasevich.
3) Support GSO segmentation over tunnels and other encapsulating
devices such as VXLAN, from Pravin B Shelar.
4) Support L2 GRE tunnels in the flow dissector, from Michael Dalton.
5) Implement Tail Loss Probe (TLP) detection in TCP, from Nandita
Dukkipati.
6) In the PHY layer, allow supporting wake-on-lan in situations where
the PHY registers have to be written for it to be configured.
Use it to support wake-on-lan in mv643xx_eth.
From Michael Stapelberg.
7) Significantly improve firewire IPV6 support, from YOSHIFUJI
Hideaki.
8) Allow multiple packets to be sent in a single transmission using
network coding in batman-adv, from Martin Hundebøll.
9) Add support for T5 cxgb4 chips, from Santosh Rastapur.
10) Generalize the VXLAN forwarding tables so that there is more
flexibility in configurating various aspects of the endpoints.
From David Stevens.
11) Support RSS and TSO in hardware over GRE tunnels in bxn2x driver,
from Dmitry Kravkov.
12) Zero copy support in nfnelink_queue, from Eric Dumazet and Pablo
Neira Ayuso.
13) Start adding networking selftests.
14) In situations of overload on the same AF_PACKET fanout socket, or
per-cpu packet receive queue, minimize drop by distributing the
load to other cpus/fanouts. From Willem de Bruijn and Eric
Dumazet.
15) Add support for new payload offset BPF instruction, from Daniel
Borkmann.
16) Convert several drivers over to mdoule_platform_driver(), from
Sachin Kamat.
17) Provide a minimal BPF JIT image disassembler userspace tool, from
Daniel Borkmann.
18) Rewrite F-RTO implementation in TCP to match the final
specification of it in RFC4138 and RFC5682. From Yuchung Cheng.
19) Provide netlink socket diag of netlink sockets ("Yo dawg, I hear
you like netlink, so I implemented netlink dumping of netlink
sockets.") From Andrey Vagin.
20) Remove ugly passing of rtnetlink attributes into rtnl_doit
functions, from Thomas Graf.
21) Allow userspace to be able to see if a configuration change occurs
in the middle of an address or device list dump, from Nicolas
Dichtel.
22) Support RFC3168 ECN protection for ipv6 fragments, from Hannes
Frederic Sowa.
23) Increase accuracy of packet length used by packet scheduler, from
Jason Wang.
24) Beginning set of changes to make ipv4/ipv6 fragment handling more
scalable and less susceptible to overload and locking contention,
from Jesper Dangaard Brouer.
25) Get rid of using non-type-safe NLMSG_* macros and use nlmsg_*()
instead. From Hong Zhiguo.
26) Optimize route usage in IPVS by avoiding reference counting where
possible, from Julian Anastasov.
27) Convert IPVS schedulers to RCU, also from Julian Anastasov.
28) Support cpu fanouts in xt_NFQUEUE netfilter target, from Holger
Eitzenberger.
29) Network namespace support for nf_log, ebt_log, xt_LOG, ipt_ULOG,
nfnetlink_log, and nfnetlink_queue. From Gao feng.
30) Implement RFC3168 ECN protection, from Hannes Frederic Sowa.
31) Support several new r8169 chips, from Hayes Wang.
32) Support tokenized interface identifiers in ipv6, from Daniel
Borkmann.
33) Use usbnet_link_change() helper in USB net driver, from Ming Lei.
34) Add 802.1ad vlan offload support, from Patrick McHardy.
35) Support mmap() based netlink communication, also from Patrick
McHardy.
36) Support HW timestamping in mlx4 driver, from Amir Vadai.
37) Rationalize AF_PACKET packet timestamping when transmitting, from
Willem de Bruijn and Daniel Borkmann.
38) Bring parity to what's provided by /proc/net/packet socket dumping
and the info provided by netlink socket dumping of AF_PACKET
sockets. From Nicolas Dichtel.
39) Fix peeking beyond zero sized SKBs in AF_UNIX, from Benjamin
Poirier"
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (1722 commits)
filter: fix va_list build error
af_unix: fix a fatal race with bit fields
bnx2x: Prevent memory leak when cnic is absent
bnx2x: correct reading of speed capabilities
net: sctp: attribute printl with __printf for gcc fmt checks
netlink: kconfig: move mmap i/o into netlink kconfig
netpoll: convert mutex into a semaphore
netlink: Fix skb ref counting.
net_sched: act_ipt forward compat with xtables
mlx4_en: fix a build error on 32bit arches
Revert "bnx2x: allow nvram test to run when device is down"
bridge: avoid OOPS if root port not found
drivers: net: cpsw: fix kernel warn on cpsw irq enable
sh_eth: use random MAC address if no valid one supplied
3c509.c: call SET_NETDEV_DEV for all device types (ISA/ISAPnP/EISA)
tg3: fix to append hardware time stamping flags
unix/stream: fix peeking with an offset larger than data in queue
unix/dgram: fix peeking with an offset larger than data in queue
unix/dgram: peek beyond 0-sized skbs
openvswitch: Remove unneeded ovs_netdev_get_ifindex()
...
The patch set is mostly driver updates (qla4, qla2 [ISF support updates],
lpfc, aacraid [dual firmware image support]) and a few bug fixes.
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.19 (GNU/Linux)
iQEcBAABAgAGBQJRgAd8AAoJEDeqqVYsXL0Mg5wH/3P4wlXaRyqvyrFk1WSkmklZ
6YxzIKn/RLFmJlJvkaTT7N02ble2UqTluB6+5+AorU/jqz6DArxHsPnyv0/+2pXS
zYmp1hrcLn9dB3sZ2Y32jU2GlzHq+LSJSjjnUrA/uRrq1KTP09KCJtGbZUkvy710
x1/3e3I8u2bvBAehUkKvazg5+xlw/XImJ+IVXgUWOyiv1mNbqNEtT5qYt7sjnhLu
Mg2VfKTSb+kzxSpol3v51vh/wqY6unVcI/a9HxanihkDtkqRBRhg8wXpNAYI2xNK
uNLGq0VFpyCYfBZX0aqh01QZ++EUU2TNlRreVg4/crQnBR88EI3KtUsA1BOthwQ=
=x6dL
-----END PGP SIGNATURE-----
Merge tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull first round of SCSI updates from James "Jej B" Bottomley:
"The patch set is mostly driver updates (qla4, qla2 [ISF support
updates], lpfc, aacraid [dual firmware image support]) and a few bug
fixes"
* tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi: (47 commits)
[SCSI] iscsi_tcp: support PF_MEMALLOC/__GFP_MEMALLOC
[SCSI] libiscsi: avoid unnecessary multiple NULL assignments
[SCSI] qla4xxx: Update driver version to 5.03.00-k8
[SCSI] qla4xxx: Added print statements to display AENs
[SCSI] qla4xxx: Use correct value for max flash node entries
[SCSI] qla4xxx: Restrict logout from boot target session using session id
[SCSI] qla4xxx: Use correct flash ddb offset for ISP40XX
[SCSI] isci: add CONFIG_PM_SLEEP to suspend/resume functions
[SCSI] scsi_dh_alua: Add module parameter to allow failover to non preferred path without STPG
[SCSI] qla2xxx: Update the driver version to 8.05.00.03-k.
[SCSI] qla2xxx: Obtain loopback iteration count from bsg request.
[SCSI] qla2xxx: Add clarifying printk to thermal access fail cases.
[SCSI] qla2xxx: Remove duplicated include form qla_isr.c
[SCSI] qla2xxx: Enhancements to support ISPFx00.
[SCSI] qla4xxx: Update driver version to 5.03.00-k7
[SCSI] qla4xxx: Replace dev type macros with generic portal type macros
[SCSI] scsi_transport_iscsi: Declare portal type string macros for generic use
[SCSI] qla4xxx: Add flash node mgmt support
[SCSI] libiscsi: export function iscsi_switch_str_param
[SCSI] scsi_transport_iscsi: Add flash node mgmt support
...
Pull SCSI target update from Nicholas Bellinger:
"The highlights this round include:
- Add fileio support for WRITE_SAME w/ UNMAP=1 discard (asias)
- Add fileio support for UNMAP discard (asias)
- Add tcm_vhost hotplug support to work with upstream QEMU
vhost-scsi-pci code (asias + mst)
- Check for aborted sequence in tcm_fc response path (mdr)
- Add initial iscsit_transport support into iscsi-target code (nab)
- Refactor iscsi-target RX PDU logic + export request PDU handling
(nab)
- Refactor iscsi-target TX queue logic + export response PDU creation
(nab)
- Add new iSCSI Extentions for RDMA (ISER) target driver (Or + nab)
The biggest changes revolve around iscsi-target refactoring in order
to support the iser-target driver. This includes the conversion of
the iscsi-target data-path to use modern se_cmd->cmd_kref counting,
and allowing transport independent aspects of RX/TX PDU
request/response handling be shared across existing traditional
iscsi-target code, and the new iser-target code.
Thanks to Or Gerlitz + Mellanox for supporting the iser-target
development effort!"
* 'for-next-merge' of git://git.kernel.org/pub/scm/linux/kernel/git/nab/target-pending: (25 commits)
iser-target: Add iSCSI Extensions for RDMA (iSER) target driver
tcm_vhost: Enable VIRTIO_SCSI_F_HOTPLUG
tcm_vhost: Add ioctl to get and set events missed flag
tcm_vhost: Add hotplug/hotunplug support
tcm_vhost: Refactor the lock nesting rule
tcm_fc: Check for aborted sequence
iscsi-target: Add iser network portal attribute
iscsi-target: Refactor TX queue logic + export response PDU creation
iscsi-target: Refactor RX PDU logic + export request PDU handling
iscsi-target: Add per transport iscsi_cmd alloc/free
iscsi-target: Add iser-target parameter keys + setup during login
iscsi-target: Initial traditional TCP conversion to iscsit_transport
iscsi-target: Add iscsit_transport API template
target: Add export of target_get_sess_cmd symbol
target: Change default sense key of NOT_READY
target/file: Set is_nonrot attribute
target: Add sbc_execute_unmap() helper
target/iblock: Add iblock_do_unmap() helper
target/file: Add fd_do_unmap() helper
target/file: Add UNMAP emulation support
...
Use preferable function name which implies using a pseudo-random
number generator.
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Cc: "James E.J. Bottomley" <JBottomley@parallels.com>
Cc: Robert Love <robert.w.love@intel.com>
Cc: James Smart <james.smart@emulex.com>
Cc: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Don't use create_proc_read_entry() as that is deprecated, but rather use
proc_create_data() and seq_file instead.
Signed-off-by: David Howells <dhowells@redhat.com>
cc: Neela Syam Kolli <megaraidlinux@lsi.com>
cc: James E.J. Bottomley <JBottomley@parallels.com>
cc: linux-scsi@vger.kernel.org
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
mind you, I'm not sure WTF would anybody _need_ that miscdevice
at all - no IO is possible for it, opening it only pins the module
down and is seriously racy, at that.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
The firmware supports a maximum of 4K FCoE exchanges. In 4-port devices,
or when working in multi-function mode, this resource needs to be distributed
between the various possible FCoE functions.
This information needs to be calculated by bnx2x and propagated into bnx2fc
via cnic. bnx2fc can then use this value to calculate corresponding xid
resources instead of using global constants.
Signed-off-by: Bhanu Prakash Gollapudi <bprakash@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It was already unused when first introduced in 2d70c103.
Signed-off-by: Joern Engel <joern@logfs.org>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
* pci/gavin-msi-cleanup:
vfio-pci: Use cached MSI/MSI-X capabilities
vfio-pci: Use PCI_MSIX_TABLE_BIR, not PCI_MSIX_FLAGS_BIRMASK
PCI: Remove "extern" from function declarations
PCI: Use PCI_MSIX_TABLE_BIR, not PCI_MSIX_FLAGS_BIRMASK
PCI: Drop msi_mask_reg() and remove drivers/pci/msi.h
PCI: Use msix_table_size() directly, drop multi_msix_capable()
PCI: Drop msix_table_offset_reg() and msix_pba_offset_reg() macros
PCI: Drop is_64bit_address() and is_mask_bit_support() macros
PCI: Drop msi_data_reg() macro
PCI: Drop msi_lower_address_reg() and msi_upper_address_reg() macros
PCI: Drop msi_control_reg() macro and use PCI_MSI_FLAGS directly
PCI: Use cached MSI/MSI-X offsets from dev, not from msi_desc
PCI: Clean up MSI/MSI-X capability #defines
PCI: Use cached MSI-X cap while enabling MSI-X
PCI: Use cached MSI cap while enabling MSI interrupts
PCI: Remove MSI/MSI-X cap check in pci_msi_check_device()
PCI: Cache MSI/MSI-X capability offsets in struct pci_dev
PCI: Use u8, not int, for PM capability offset
[SCSI] megaraid_sas: Use correct #define for MSI-X capability
Fix typo in printk and comments within various drivers.
Signed-off-by: Masanari Iida <standby24x7@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Conflicts:
drivers/net/ethernet/emulex/benet/be_main.c
drivers/net/ethernet/intel/igb/igb_main.c
drivers/net/wireless/brcm80211/brcmsmac/mac80211_if.c
include/net/scm.h
net/batman-adv/routing.c
net/ipv4/tcp_input.c
The e{uid,gid} --> {uid,gid} credentials fix conflicted with the
cleanup in net-next to now pass cred structs around.
The be2net driver had a bug fix in 'net' that overlapped with the VLAN
interface changes by Patrick McHardy in net-next.
An IGB conflict existed because in 'net' the build_skb() support was
reverted, and in 'net-next' there was a comment style fix within that
code.
Several batman-adv conflicts were resolved by making sure that all
calls to batadv_is_my_mac() are changed to have a new bat_priv first
argument.
Eric Dumazet's TS ECR fix in TCP in 'net' conflicted with the F-RTO
rewrite in 'net-next', mostly overlapping changes.
Thanks to Stephen Rothwell and Antonio Quartulli for help with several
of these merge resolutions.
Signed-off-by: David S. Miller <davem@davemloft.net>
Rename the hardware VLAN acceleration features to include "CTAG" to indicate
that they only support CTAGs. Follow up patches will introduce 802.1ad
server provider tagging (STAGs) and require the distinction for hardware not
supporting acclerating both.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Previously we used PCI_MSI_FLAGS to locate a register in the MSI-X
capability. This did work because the MSI and MSI-X flags happen
to be at the same offsets, but was confusing.
PCI_MSIX_FLAGS_ENABLE is already defined in include/uapi/linux/pci_regs.h,
so no need to define it again.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Adam Radford <aradford@gmail.com>
With the 0x1b4b vendor ID #define in place, convert hard-coded ID
values.
Signed-off-by: Myron Stowe <myron.stowe@redhat.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: James Bottomley <James.Bottomley@hansenpartnership.com>
With the 0x1b4b vendor ID #define in place, convert hard-coded ID
values.
Signed-off-by: Myron Stowe <myron.stowe@redhat.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: James Bottomley <James.Bottomley@hansenpartnership.com>
This patch has software iscsi use PF_MEMALLOC/__GFP_MEMALLOC
to be able to better support swap over iscsi disks similar to
what was added for nbd.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
In iscsi_free_task, NULL is assigned to task->sc twice: before and
after kfifo_in invocatoin. Allocating and freeing iscsi_task are guarded
with session->lock, so multiple NULL assignments cause no trouble. But
people reading the source code may be confused.
The second NULL assignment comes from commit:
3e5c28ad03
It seems that the line after kfifo_in invocation was introduced
accidentally.
Signed-off-by: Masatake YAMATO <yamato@redhat.com>
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Use correct value for max flash node entries supported
based on adapter type.
Signed-off-by: Adheer Chandravanshi <adheer.chandravanshi@qlogic.com>
Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Use correct flash ddb offset to add and delete flash target
entries for ISP40XX
Signed-off-by: Adheer Chandravanshi <adheer.chandravanshi@qlogic.com>
Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Add CONFIG_PM_SLEEP to suspend/resume functions to fix the following
build warning when CONFIG_PM_SLEEP is not selected. This is because
sleep PM callbacks defined by SIMPLE_DEV_PM_OPS are only used when
the CONFIG_PM_SLEEP is enabled.
drivers/scsi/isci/init.c:725:12: warning: 'isci_suspend' defined but not used [-Wunused-function]
drivers/scsi/isci/init.c:743:12: warning: 'isci_resume' defined but not used [-Wunused-function]
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Acked-by: Lukasz Dorau <lukasz.dorau@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Resending with requested rewording of the parameter description. Currently
ALUA device handler sends STPG command during failover and failback. Failover
can be optimized by implicit failover (by not to sending STPG command), when 1
is passed as hwhandler parameter in multipath.conf. ex "2 alua 1". We may need
to pass the parameter through module param for alua device handler to optimize
failover if incase retain_attached_hwhandler set in multipath.conf and
hwhandler is set with non-tpgs device handler ex: '1 rdac'.
[jejb: fix up whitespace and other issues]
Signed-off-by: Vijay Chauhan <vijay.chauhan@netapp.com>
Signed-off-by: Sean Stewart <Sean.Stewart@netapp.com>
Acked-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
qla2x00_loopback_test() was hard setting the loopback iteration
count to 1 rather than obtaining it from the bsg request.
Signed-off-by: Joe Carnuccio <joe.carnuccio@qlogic.com>
Signed-off-by: Saurav Kashyap <saurav.kashyap@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
This patch allows iscsiadm to manage iSCSI target information stored on
qla4xxx adapter flash on per host basis.
Signed-off-by: Adheer Chandravanshi <adheer.chandravanshi@qlogic.com>
Signed-off-by: Manish Rangankar <manish.rangankar@qlogic.com>
Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
This patch allows iscsiadm to manage iSCSI target information stored on
adapter flash on per host basis.
The sysfs entries will look as cited below:
/sys/bus/iscsi_flashnode/devices/flashnode_sess-<host_no>:<flashnode_id>/<session attrs>
/sys/bus/iscsi_flashnode/devices/flashnode_conn-<host_no>:<flashnode_id>:<conn_id>/<conn attrs>
Signed-off-by: Adheer Chandravanshi <adheer.chandravanshi@qlogic.com>
Signed-off-by: Manish Rangankar <manish.rangankar@qlogic.com>
Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
While probe Skip retry of initialize_adapter only for ISP82XX and ISP83XX.
We need to retry initialize_adapter for ISP40XX.
Signed-off-by: Nilesh Javali <nilesh.javali@qlogic.com>
Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Issue:
If flash read for FLT fails, we are assigning wrong default
address for CHAP table in FLT, which will cause CHAP table
read/write to wrong address.
Fix:
Assign correct default CHAP table address to FLT.
Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
The dereference to 'put_index' should be moved below the NULL test.
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Acked-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
This patch adds dual flash firmware support for Series 7 and above controllers.
[thenzl: used ssleep(10) instead udelay]
Signed-off-by: Mahesh Rajashekhara <Mahesh.Rajashekhara@pmcs.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
The variable 'data' is initialized but never used
otherwise, so remove the unused variable.
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Acked-by: Naresh Kumar Inna <naresh@chelsio.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Issue:
Request queue count holds the information about free space in request queue
which has to be manipulated based on request in and out pointer.
But in driver response path, this count was incremented unconditionally,
which could move req_in pointer beyond req_out pointer.
This scenario leads fw hang during IO.
Solution:
Request queue count manipulation has to be done in IO path only, keeping
req_in and req_out pointer two IOCB count away
Signed-off-by: Tej Parkash <tej.parkash@qlogic.com>
Signed-off-by: Shyam Sundar <shyam.sundar@qlogic.com>
Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Move "Incorrect function ID" print message in case INTX interrupt
from DEBUG2 to DEBUG7. This will avoid floods of this message if
DEBUG2 is enabled.
Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Use function int_to_scsilun() in qla4xxx_reset_lun() to convert
integer value comming from scsi_transport to scsi LUN address format.
Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
In case of firmware hung we need to call "mailbox_premature_completion" to
complete any pending mbox command as firmware is not alive.
Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
For ISP83XX set graceful reset bit in IDC_DRV_CTRL
if reset is issued by application
Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Issue:
ISP83XX check is missing in function get_fw_boot_info() because of this
qla4xxx will not export boot target to sysfs and iscsistart cannot issue
login to boot target.
Fix:
Added check for ISP83XX in function get_fw_boot_info()
Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Problem Description:
Disabling pause frames might cause hardware wedging needing a power cycle.
This might happen if the Eport is not initialized and is in reset.
Solution:
Before disabling pause frames ensure that eport is out of reset.
Signed-off-by: Manish Dusane <manish.dusane@qlogic.com>
Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
For the stpg_endio path we are not evaluating the sense. The bug
is that
1. The error value is set to -EIO when there is sense, so we hit the first
error check and always return SCSI_DH_IO.
2. h->senselen is set to zero in submit_stpg. It is not later set to
req->sense_len like in the synchrounous exection paths, so we must
check the req->sense_len field.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
The service parameters for the VPI/RPIs were incorrect, resulting in
lower utilization
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Fixed NMI watch dog panic's when resetting the hba.
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
The only part of proc_dir_entry the code outside of fs/proc
really cares about is PDE(inode)->data. Provide a helper
for that; static inline for now, eventually will be moved
to fs/proc, along with the knowledge of struct proc_dir_entry
layout.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Some of the ->show_info() instances really spew a lot; it's not a problem
wrt correctness (seq_read() will grow buffer and call the sucker again),
but in this case it makes sense to start with a somewhat bigger one -
they often do exceed one page worth of output.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
asc_prt_line() had been hiding several places where formats had not
matched the argument types. The previous commit has finally made them
visible...
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
It's still an obsolete interface; don't introduce those in new drivers.
However, it's saner than the ->proc_info() and commits after this one
will convert the existing ->proc_info() users to it.
The read side is ->show_info(seq_file *, struct Scsi_Host *); use
seq_... for generating contents.
The write side is ->write_info(struct Scsi_Host *, char *, int).
Again, this is driven by procfs needs; we are going to kill ->write_proc()
and ->read_proc() and this is the main obstacle to burying that piece of
shit.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Add hot cpu notifier to reset the request virtqueue affinity
when doing cpu hotplug.
Cc: linux-scsi@vger.kernel.org
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Wanlong Gao <gaowanlong@cn.fujitsu.com>
Reviewed-by: Asias He <asias@redhat.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
This patch adds queue steering to virtio-scsi. When a target is sent
multiple requests, we always drive them to the same queue so that FIFO
processing order is kept. However, if a target was idle, we can choose
a queue arbitrarily. In this case the queue is chosen according to the
current VCPU, so the driver expects the number of request queues to be
equal to the number of VCPUs. This makes it easy and fast to select
the queue, and also lets the driver optimize the IRQ affinity for the
virtqueues (each virtqueue's affinity is set to the CPU that "owns"
the queue).
The speedup comes from improving cache locality and giving CPU affinity
to the virtqueues, which is why this scheme was selected. Assuming that
the thread that is sending requests to the device is I/O-bound, it is
likely to be sleeping at the time the ISR is executed, and thus executing
the ISR on the same processor that sent the requests is cheap.
However, the kernel will not execute the ISR on the "best" processor
unless you explicitly set the affinity. This is because in practice
you will have many such I/O-bound processes and thus many otherwise
idle processors. Then the kernel will execute the ISR on a random
processor, rather than the one that is sending requests to the device.
The alternative to per-CPU virtqueues is per-target virtqueues. To
achieve the same locality, we could dynamically choose the virtqueue's
affinity based on the CPU of the last task that sent a request. This
is less appealing because we do not set the affinity directly---we only
provide a hint to the irqbalanced running in userspace. Dynamically
changing the affinity only works if the userspace applies the hint
fast enough.
Cc: linux-scsi@vger.kernel.org
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Wanlong Gao <gaowanlong@cn.fujitsu.com>
Reviewed-by: Asias He <asias@redhat.com>
Tested-by: Venkatesh Srinivas <venkateshs@google.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Avoid duplicated code in all of the callers.
Cc: linux-scsi@vger.kernel.org
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Wanlong Gao <gaowanlong@cn.fujitsu.com>
Reviewed-by: Asias He <asias@redhat.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
This will be needed soon in order to retrieve the per-target
struct.
Cc: linux-scsi@vger.kernel.org
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Wanlong Gao <gaowanlong@cn.fujitsu.com>
Reviewed-by: Asias He <asias@redhat.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
virtio_scsi_target_state is now empty. We will find new uses for it in
the next few patches, so this patch does not drop it completely.
And as James suggested, we use entries target_alloc and target_destroy
in the host template to allocate and destroy the virtio_scsi_target_state
of each target, attach this struct to scsi_target->hostdata. Now
we can get at it from the sdev with scsi_target(sdev)->hostdata.
No messing around with fixed size arrays and bulk memory allocation
and no need to pass in the maximum target size as a parameter because
everything should now happen dynamically.
Cc: James Bottomley <James.Bottomley@HansenPartnership.com>
Cc: linux-scsi@vger.kernel.org
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Wanlong Gao <gaowanlong@cn.fujitsu.com>
Reviewed-by: Asias He <asias@redhat.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
If a result of the SMP discover function is PHY VACANT,
the content of discover response structure (dr) is not valid.
It sometimes happens that dr->attached_sas_addr can contain
even SAS address of other phy. In such case an invalid phy
is created, what causes NULL pointer dereference during
destruction of expander's phys.
So if a result of SMP function is PHY VACANT, the content of discover
response structure (dr) must not be copied to phy structure.
This patch fixes the following bug:
BUG: unable to handle kernel NULL pointer dereference at 0000000000000030
IP: [<ffffffff811c9002>] sysfs_find_dirent+0x12/0x90
Call Trace:
[<ffffffff811c95f5>] sysfs_get_dirent+0x35/0x80
[<ffffffff811cb55e>] sysfs_unmerge_group+0x1e/0xb0
[<ffffffff813329f4>] dpm_sysfs_remove+0x24/0x90
[<ffffffff8132b0f4>] device_del+0x44/0x1d0
[<ffffffffa016fc59>] sas_rphy_delete+0x9/0x20 [scsi_transport_sas]
[<ffffffffa01a16f6>] sas_destruct_devices+0xe6/0x110 [libsas]
[<ffffffff8107ac7c>] process_one_work+0x16c/0x350
[<ffffffff8107d84a>] worker_thread+0x17a/0x410
[<ffffffff81081b76>] kthread+0x96/0xa0
[<ffffffff81464944>] kernel_thread_helper+0x4/0x10
Signed-off-by: Lukasz Dorau <lukasz.dorau@intel.com>
Signed-off-by: Pawel Baldysiak <pawel.baldysiak@intel.com>
Reviewed-by: Maciej Patelczyk <maciej.patelczyk@intel.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
No locks should be held when calling scsi_adjust_queue_depth
so drop the lock in slave_configure prior to calling it.
Signed-off-by: Brian King <brking@linux.vnet.ibm.com>
Acked-by: Robert Jennings <rcj@linux.vnet.ibm.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
System crashes, in initiator mode operation, with
qla2xxx_copy_atioqueues() in stack trace when firmware dump is
attempted.
Check for atio_q_length alone does not indicate if atio_ring is
allocated, make explicit check of atio_ring to avoid the crash.
Applicable to ISP24xx, ISP25xx, ISP81xx & ISP83xx line of HBAs.
Signed-off-by: Arun Easi <arun.easi@qlogic.com>
Signed-off-by: Saurav Kashyap <saurav.kashyap@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
The original patch was not covering all the adapters and firmwares.
This commit reverts 3a11711ad0.
Signed-off-by: Joe Carnuccio <joe.carnuccio@qlogic.com>
Signed-off-by: Saurav Kashyap <saurav.kashyap@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Reinitialize resource queue prior to freeing resource entries to ensure they
are not referenced. This fixes an issue with target_destoy accessing memory
after it was freed.
Signed-off-by: Wen Xiong <wenxiong@linux.vnet.ibm.com>
Acked-by: Brian King <brking@linux.vnet.ibm.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
The abort command issued by ipr_cancel_op() is being added to the wrong
HRRQ free queue after the command returns. Fix it by using the HRRQ
pointer in the ipr command struct itself.
Signed-off-by: Kleber Sacilotto de Souza <klebers@linux.vnet.ibm.com>
Signed-off-by: Wen Xiong <wenxiong@linux.vnet.ibm.com>
Acked-by: Brian King <brking@linux.vnet.ibm.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
This patch fixes a reference count bug in the SCSI tape driver which can be
reproduced with the following:
* Boot with slub_debug=FZPU, tape drive attached
* echo 1 > /sys/devices/... tape device pci path .../remove
* Wait for device removal
* echo 1 > /sys/kernel/slab/blkdev_queue/validate
* Slub debug complains about corrupted poison pattern
In commit 523e1d39 (block: make gendisk hold a reference to its queue)
add_disk() and disk_release() were modified to get/put an additional
reference on a disk queue to fix a reference counting discrepency
between bdev release and SCSI device removal. The ST driver never
calls add_disk(), so this commit introduced an extra kref put when the
ST driver frees its struct gendisk.
Attempts were made to fix this bug at the block level [1] but later
abandoned due to floppy driver issues [2].
[1] https://lkml.org/lkml/2012/8/27/354
[2] https://lkml.org/lkml/2012/9/22/113
Signed-off-by: Joe Lawrence <joe.lawrence@stratus.com>
Tested-by: Ewan D. Milne <emilne@redhat.com>
Acked-by: Kai Mäkisara <Kai.Makisara@kolumbus.fi>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
In fact the disc_resp buffer will be overwrite by smp response, so we never
found this typo, correct it by using the right one.
Signed-off-by: John Gong <john_gong@usish.com>
Signed-off-by: Jack Wang <jack_wang@usish.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Loading ipr modules failed(-22) with msi-x enabled adapter. In ipr_test_msi(),
We need to pass the first vector of msix vectors instead of using pdev->irq
to request_irq() when adapter enables msix feature.
Signed-off-by: Wen Xiong <wenxiong@linux.vnet.ibm.com>
Acked-by: Brian King <brking@linux.vnet.ibm.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Correct spelling typos in various part of printk.
Signed-off-by: Masanari Iida <standby24x7@gmail.com>
Acked-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The libfc discovery layer is being initialized in the
'create' paths for both legacy libfcoe module parameters
and fcoe_sysfs control interfaces. The problem is that
for VN2VN mode the discovery layer is initialized as if
it were in 'fabric' mode and it is not re-configured when
the mode is changed to 'vn2vn'.
This patch splits out code that needs to be initialized
once and code that can, and should be, re-configured when
the mode changes. Additionally this patch makes that change
so that the discovery layer can be reconfigured to the
libfcoe implementation when in 'vn2vn' mode.
Signed-off-by: Robert Love <robert.w.love@intel.com>
Tested-by: Jack Morgan <jack.morgan@intel.com>
Reviewed-by: Bhanu Prakash Gollapudi <bprakash@broadcom.com>
Split discovery initialization in code that is setup once (fcoe_disc_init)
and code that can be re-configured (fcoe_disc_config).
Signed-off-by: Robert Love <robert.w.love@intel.com>
Tested-by: Jack Morgan <jack.morgan@intel.com>
Reviewed-by: Bhanu Prakash Gollapudi <bprakash@broadcom.com>
Currently libfcoe is doing some libfc discovery layer initialization outside of
libfc. This patch moves this code into libfc and sets up a split in discovery
(one time) initialization code and (re-configurable) settings that will come in
the next patch.
Signed-off-by: Robert Love <robert.w.love@intel.com>
Tested-by: Jack Morgan <jack.morgan@intel.com>
Reviewed-by: Bhanu Prakash Gollapudi <bprakash@broadcom.com>
The fcoemon userspace daemon is searching for the a hostX
under the the /sys/bus/fcoe/devices/ctlrX/ entries. When
interfaces created using fcoe_sysfs and fcoe.ko this linkage
is setup correctly, but bnx2fc is not doing the same thing
and therefore fcoemon does not create the fcoe interface
for bnx2fc.
This patch sets up the correct linkage for bnx2fc such that
fcoemon will work correctly with fcoe_sysfs and bnx2fc.
Signed-off-by: Robert Love <robert.w.love@intel.com>
Acked-by: Bhanu Prakash Gollapudi <bprakash@broadcom.com>
More prep work for immutable bvecs/effecient bio splitting - usage of
bi_vcnt has to be auditing, so getting rid of all the unnecessary usage
makes that easier.
Plus, bio_segments() is really what this code wanted, as it respects the
current value of bi_idx.
Signed-off-by: Kent Overstreet <koverstreet@google.com>
CC: Jens Axboe <axboe@kernel.dk>
CC: Eric Moore <Eric.Moore@lsi.com>
CC: "James E.J. Bottomley" <JBottomley@parallels.com>
CC: linux-scsi@vger.kernel.org
Using the new virtqueue_add_sgs function lets us simplify the queueing
path. In particular, all data protected by the tgt_lock is just gone
(multiqueue will find a new use for the lock).
Signed-off-by: Wanlong Gao <gaowanlong@cn.fujitsu.com>
Acked-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Asias He <asias@redhat.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
This patch removes chip specific operations from the common hardware
paths, as well as the Makefile change to accomodate the new files.
Signed-off-by: Arvind Bhushan <arvindb@chelsio.com>
Signed-off-by: Naresh Kumar Inna <naresh@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch defines the common operations to support multiple chips. It
includes common header file modifications to support the current chips
(T4 and T5). It also includes the following bug fixes:
- reconfirms the rnode state after an implicit logo.
- corrects the stats array size.
- sets up and checks flags correctly when coming up as master and finding
the card initialized
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Arvind Bhushan <arvindb@chelsio.com>
Signed-off-by: Naresh Kumar Inna <naresh@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch creates a new file for T5 adapter operations.
Signed-off-by: Arvind Bhushan <arvindb@chelsio.com>
Signed-off-by: Naresh Kumar Inna <naresh@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch separates T4 adapter operations into a new file.
Signed-off-by: Arvind Bhushan <arvindb@chelsio.com>
Signed-off-by: Naresh Kumar Inna <naresh@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Convert the virtio-scsi driver to use pr_err() instead of printk().
Signed-off-by: Wanlong Gao <gaowanlong@cn.fujitsu.com>
Acked-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
USB uses the .find_bridge() callback from struct acpi_bus_type
incorrectly, because as a result of the way it is used by USB every
device in the system that doesn't have a bus type or parent is
passed to usb_acpi_find_device() for inspection.
What USB actually needs, though, is to call usb_acpi_find_device()
for USB ports that don't have a bus type defined, but have
usb_port_device_type as their device type, as well as for USB
devices.
To fix that replace the struct bus_type pointer in struct
acpi_bus_type used for matching devices to specific subsystems
with a .match() callback to be used for this purpose and update
the users of struct acpi_bus_type, including USB, accordingly.
Define the .match() callback routine for USB, usb_acpi_bus_match(),
in such a way that it will cover both USB devices and USB ports
and remove the now redundant .find_bridge() callback pointer from
usb_acpi_bus.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: Yinghai Lu <yinghai@kernel.org>
Acked-by: Jeff Garzik <jgarzik@pobox.com>
This is an assorted set of stragglers into the merge window with driver
updates for qla2xxx, megaraid_sas, storvsc and ufs. It also includes pulls of
the uapi tree (all the remaining SCSI pieces) and the fcoe tree (updates to
fcoe and libfc)
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.19 (GNU/Linux)
iQEcBAABAgAGBQJRMHJHAAoJEDeqqVYsXL0M9tAH/2YG3TCfy0RFAejGgLfX9OGH
6eFe71m7Z8nfIEneAnm5BuKjCx3QFRp5UFjJZdFHLP1Qv0TbpKs4FnZyeSGTxLQp
S1fZc5sTWmsb5qYxLaukKopC6sFx+hNI2dvB+rgKcd+nWy1RzG7lGqbS4CRNE76q
UNByqlfqJxn5cfQw7dg2zOUKlGaGL2jSyFf0QFXR2IZzO33PeyBPfKDFeJC6b+oc
XTy9MK9V5u6ne3XimDTU2hP4lPAsZaJtcqsv1Gvv2y+BHalQiPqfL6bZMvN3Zbfq
hfT+i2xnYy85858gxtyIhzHwU14zF7I0HEWiVpddsF9NDK7iNKvK8aWHaTs7qis=
=hvGQ
-----END PGP SIGNATURE-----
Merge tag 'scsi-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI updates from James Bottomley:
"This is an assorted set of stragglers into the merge window with
driver updates for qla2xxx, megaraid_sas, storvsc and ufs.
It also includes pulls of the uapi tree (all the remaining SCSI
pieces) and the fcoe tree (updates to fcoe and libfc)"
* tag 'scsi-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi: (81 commits)
[SCSI] ufs: Separate PCI code into glue driver
[SCSI] ufs: Segregate PCI Specific Code
[SCSI] scsi: fix lpfc build when wmb() is defined as mb()
[SCSI] storvsc: Handle dynamic resizing of the device
[SCSI] storvsc: Restructure error handling code on command completion
[SCSI] storvsc: avoid usage of WRITE_SAME
[SCSI] aacraid: suppress two GCC warnings
[SCSI] hpsa: check for dma_mapping_error in hpsa_passthru ioctls
[SCSI] hpsa: reorganize error handling in hpsa_passthru_ioctl
[SCSI] hpsa: check for dma_mapping_error in hpsa_map_sg_chain_block
[SCSI] hpsa: Check for dma_mapping_error for all code paths using fill_cmd
[SCSI] hpsa: Check for dma_mapping_error in hpsa_map_one
[SCSI] dc395x: uninitialized variable in device_alloc()
[SCSI] Fix range check in scsi_host_dif_capable()
[SCSI] storvsc: Initialize the sglist
[SCSI] mpt2sas: Add support for OEM specific controller
[SCSI] ipr: Fix oops while resetting an ipr adapter
[SCSI] fnic: Fnic Trace Utility
[SCSI] fnic: New debug flags and debug log messages
[SCSI] fnic: fnic driver may hit BUG_ON on device reset
...
he patch set is mostly driver updates (bnx2fc, ipr, lpfc, qla4) and a few bug
fixes.
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.19 (GNU/Linux)
iQEcBAABAgAGBQJRJ0oJAAoJEDeqqVYsXL0MVVoH/A8xFiLkdCXaFkhYMlGRrDox
wgK/RwWekDOtVS2poPhDGKRfXaUn4uA3iOJig8HC5lD8NS65DElCpCWM+/DhitXt
Ky4ukgXSQ09IQtWraGqr//MC/YqM8iimWnGgXSouLPJ7a3AqYVIYCg9CEkGJX/mD
i09aE8uUyNd3Wp68anQ2w0RCH/7/InLL348WFmQ1eWxYyFJnLYGRkASbkuHxPjgU
H4QmINFlI4kBMWdHkVinh0w7cjcmUOAU+KyAZ75aelQ6dZ2aJioKn3BS7D6gF9jv
jJpJMIj8LzpAnfR3Z5ijkkcVG7E0ht+Dtr6kmAPZQJnkc/GdQvvgEg+F9aIpxoU=
=oDz4
-----END PGP SIGNATURE-----
Merge tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull first round of SCSI updates from James Bottomley:
"The patch set is mostly driver updates (bnx2fc, ipr, lpfc, qla4) and a
few bug fixes"
Pull delayed because google hates James, and sneakily considers his pull
requests spam. Why, google, why?
* tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi: (60 commits)
[SCSI] aacraid: 1024 max outstanding command support for Series 7 and above
[SCSI] bnx2fc: adjust duplicate test
[SCSI] qla4xxx: Update driver version to 5.03.00-k4
[SCSI] qla4xxx: Fix return code for qla4xxx_session_get_param.
[SCSI] qla4xxx: wait for boot target login response during probe.
[SCSI] qla4xxx: Added support for force firmware dump
[SCSI] qla4xxx: Re-register IRQ handler while retrying initialize of adapter
[SCSI] qla4xxx: Throttle active IOCBs to firmware limits
[SCSI] qla4xxx: Remove unnecessary code from qla4xxx_init_local_data
[SCSI] qla4xxx: Quiesce driver activities while loopback
[SCSI] qla4xxx: Rename MBOX_ASTS_IDC_NOTIFY to MBOX_ASTS_IDC_REQUEST_NOTIFICATION
[SCSI] qla4xxx: Add spurious interrupt messages under debug level 2
[SCSI] cxgb4i: Remove the scsi host device when removing device
[SCSI] bfa: fix strncpy() limiter in bfad_start_ops()
[SCSI] qla4xxx: Update driver version to 5.03.00-k3
[SCSI] qla4xxx: Correct the validation to check in get_sys_info mailbox
[SCSI] qla4xxx: Pass correct function param to qla4_8xxx_rd_direct
[SCSI] lpfc 8.3.37: Update lpfc version for 8.3.37 driver release
[SCSI] lpfc 8.3.37: Fixed infinite loop in lpfc_sli4_fcf_rr_next_index_get.
[SCSI] lpfc 8.3.37: Fixed crash due to SLI Port invalid resource count
...
Convert to the much saner new idr interface.
Signed-off-by: Tejun Heo <tj@kernel.org>
Acked-by: James Smart <james.smart@emulex.com>
Cc: James Bottomley <James.Bottomley@HansenPartnership.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Convert to the much saner new idr interface.
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: "James E.J. Bottomley" <James.Bottomley@HansenPartnership.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Convert to the much saner new idr interface.
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Krishna C Gudipati <kgudipat@brocade.com>
Cc: James Bottomley <James.Bottomley@HansenPartnership.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Pull vfs pile (part one) from Al Viro:
"Assorted stuff - cleaning namei.c up a bit, fixing ->d_name/->d_parent
locking violations, etc.
The most visible changes here are death of FS_REVAL_DOT (replaced with
"has ->d_weak_revalidate()") and a new helper getting from struct file
to inode. Some bits of preparation to xattr method interface changes.
Misc patches by various people sent this cycle *and* ocfs2 fixes from
several cycles ago that should've been upstream right then.
PS: the next vfs pile will be xattr stuff."
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs: (46 commits)
saner proc_get_inode() calling conventions
proc: avoid extra pde_put() in proc_fill_super()
fs: change return values from -EACCES to -EPERM
fs/exec.c: make bprm_mm_init() static
ocfs2/dlm: use GFP_ATOMIC inside a spin_lock
ocfs2: fix possible use-after-free with AIO
ocfs2: Fix oops in ocfs2_fast_symlink_readpage() code path
get_empty_filp()/alloc_file() leave both ->f_pos and ->f_version zero
target: writev() on single-element vector is pointless
export kernel_write(), convert open-coded instances
fs: encode_fh: return FILEID_INVALID if invalid fid_type
kill f_vfsmnt
vfs: kill FS_REVAL_DOT by adding a d_weak_revalidate dentry op
nfsd: handle vfs_getattr errors in acl protocol
switch vfs_getattr() to struct path
default SET_PERSONALITY() in linux/elf.h
ceph: prepopulate inodes only when request is aborted
d_hash_and_lookup(): export, switch open-coded instances
9p: switch v9fs_set_create_acl() to inode+fid, do it before d_instantiate()
9p: split dropping the acls from v9fs_set_create_acl()
...
This patch separates PCI code from ufshcd.c and makes it as a
core driver module and adds a new file ufshcd-pci.c as PCI glue
driver.
[jejb: strip __devinit and devexit_p()]
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Namjae Jeon <linkinjeon@gmail.com>
Reviewed-by: Subhash Jadavani <subhashj@codeaurora.org>
Tested-by: Maya Erez <merez@codeaurora.org>
Signed-off-by: Vinayak Holikatti <vinholikatti@gmail.com>
Signed-off-by: Santosh Yaraganavi <santoshsy@gmail.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
This patch segregates the PCI specific code in ufshcd.c to make it
ready for splitting into core ufs driver and PCI glue driver. Also
copyright header modification to remove extra warranty disclaim.
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Namjae Jeon <linkinjeon@gmail.com>
Reviewed-by: Subhash Jadavani <subhashj@codeaurora.org>
Tested-by: Maya Erez <merez@codeaurora.org>
Signed-off-by: Vinayak Holikatti <vinholikatti@gmail.com>
Signed-off-by: Santosh Yaraganavi <santoshsy@gmail.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Discussion was continuing after patch application, trying to figure out how
to best mesh exported data with the installers, boot-time agents and other
parties that want this info.
2) Merge Zero-Power Optical Device Driver (ZPODD) support, bringing
the wonderfulness of sane power management to your CD/DVD device.
Includes one SCSI-subsystem patch (with appropriate ACKs),
adding runtime PM support to 'sr' driver. That is the ZPODD interaction
bits.
Patchset went through some 13 revisions before it got here; kudos to
Intel for persistence.
3) pata_samsung_cf: use devm_clk_get()
4) more ata_piix, ahci PCI IDs
5) Add SATA driver for R-Car SoC
6) Convert libata to use devm_ioremap_resource (Note: I think
Greg sent this to you, also)
7) Set proper Sense Key (SK) in the SCSI simulator when
ATA passthrough indicates check condition. Google and specification
hawks everywhere shall rejoice.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.13 (GNU/Linux)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=YvYo
-----END PGP SIGNATURE-----
Merge tag 'upstream-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jgarzik/libata-dev
Pull libata updates from Jeff Garzik:
1) apply, and then revert, the sysfs export of ATA host controller
number. Discussion was continuing after patch application, trying to
figure out how to best mesh exported data with the installers,
boot-time agents and other parties that want this info.
2) Merge Zero-Power Optical Device Driver (ZPODD) support, bringing the
wonderfulness of sane power management to your CD/DVD device.
Includes one SCSI-subsystem patch (with appropriate ACKs), adding
runtime PM support to 'sr' driver. That is the ZPODD interaction
bits.
Patchset went through some 13 revisions before it got here; kudos to
Intel for persistence.
3) pata_samsung_cf: use devm_clk_get()
4) more ata_piix, ahci PCI IDs
5) Add SATA driver for R-Car SoC
6) Convert libata to use devm_ioremap_resource (Note: I think Greg sent
this to you, also)
7) Set proper Sense Key (SK) in the SCSI simulator when ATA passthrough
indicates check condition. Google and specification hawks everywhere
shall rejoice.
* tag 'upstream-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jgarzik/libata-dev: (22 commits)
[libata] fix smatch warning for zpodd_wake_dev
[libata] Set proper SK when CK_COND is set.
[libata] Convert to devm_ioremap_resource()
libata: add R-Car SATA driver
ahci: Add Device IDs for Intel Wellsburg PCH
ata_piix: Add Device IDs for Intel Wellsburg PCH
[SCSI] remove can_power_off flag from scsi_device
[libata] scsi: no poll when ODD is powered off
[SCSI] sr: support runtime pm
ahci: AHCI-mode SATA patch for Intel Avoton DeviceIDs
ata_piix: IDE-mode SATA patch for Intel Avoton DeviceIDs
[libata] PM code cleanup for ata port
[libata] pm: differentiate system and runtime pm for ata port
Revert "libata: export host controller number thru /sys"
libata: do not suspend port if normal ODD is attached
libata: expose pm qos flags for ata device
libata: handle power transition of ODD
libata: check zero power ready status for ZPODD
libata: move acpi notification code to zpodd
libata: identify and init ZPODD devices
...
On architectures where wmb() is defined as mb(), a build error
happens since there is also a variable named 'mb' in lpfc_sli.c's
lpfc_sli_issue_mbox_s3() function. Rename the variable to 'mbx'
to prevent the build error.
drivers/scsi/lpfc/lpfc_sli.c: error: called object 'mb' is not a function
Reported-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Acked-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Handle LUN size changes by re-scanning the device.
Signed-off-by: K. Y. Srinivasan <kys@microsoft.com>
Reviewed-by: Haiyang Zhang <haiyangz@microsoft.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
In preparation for handling additional sense codes, restructure and cleanup
the error handling code in the command completion code path.
Signed-off-by: K. Y. Srinivasan <kys@microsoft.com>
Reviewed-by: Haiyang Zhang <haiyangz@microsoft.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Set scsi_device->no_write_same because the host does not support it.
Also blacklist WRITE_SAME to avoid (and log) accident usage.
If the guest uses the ext4 filesystem, storvsc hangs while it prints
these messages in an endless loop:
...
[ 161.459523] hv_storvsc vmbus_0_1: cmd 0x41 scsi status 0x2 srb status 0x6
[ 161.462157] sd 2:0:0:0: [sda]
[ 161.463135] Sense Key : No Sense [current]
[ 161.464983] sd 2:0:0:0: [sda]
[ 161.465899] Add. Sense: No additional sense information
[ 161.468211] hv_storvsc vmbus_0_1: cmd 0x41 scsi status 0x2 srb status 0x6
[ 161.475766] sd 2:0:0:0: [sda]
[ 161.476728] Sense Key : No Sense [current]
[ 161.478284] sd 2:0:0:0: [sda]
[ 161.479441] Add. Sense: No additional sense information
...
This happens with a guest running on Windows Server 2012, but happens to
work while running on Windows Server 2008. WRITE_SAME isnt really
supported by both versions, so disable the command usage globally.
Signed-off-by: Olaf Hering <olaf@aepfle.de>
Signed-off-by: K. Y. Srinivasan <kys@microsoft.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Building src.o for a 32 bit system triggers two GCC warnings:
drivers/scsi/aacraid/src.c: In function ‘aac_src_deliver_message’:
drivers/scsi/aacraid/src.c:410:3: warning: right shift count >= width of type [enabled by default]
drivers/scsi/aacraid/src.c:434:2: warning: right shift count >= width of type [enabled by default]
These warnings are caused by a right shift of 32. Use upper_32_bits() to
suppress them.
Signed-off-by: Paul Bolle <pebolle@tiscali.nl>
Cc: Mahesh Rajashekhara <Mahesh_Rajashekhara@pmc-sierra.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Signed-off-by: Shuah Khan <shuah.khan@hp.com>
Signed-off-by: Stephen M. Cameron <scameron@beardog.cce.hp.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
This bug was introduced back in bitkeeper days in 2003. We use
"dcb->dev_mode" before it has been initialized.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Oliver Neukum <oliver@neukum.org>
Cc: <stable@vger.kernel.org>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Properly initialize scatterlist before using it.
Signed-off-by: K. Y. Srinivasan <kys@microsoft.com>
Cc: stable@vger.kernel.org
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Defined SSDID & HW vendor brand strings. Added entries for SSDID within the
function that prints the brand string.
Signed-off-by: Sreekanth Reddy <Sreekanth.Reddy@lsi.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
When resetting an ipr adapter, we use scsi_block_requests to
block any new commands from scsi core, and then unblock after
the reset. When hotplug removing an adapter, we shut it down
and go through this same code, but we've seen issues with
scsi_unblock_requests running after the adapter's memory has
been freed. There is really no need to block/unblock when
the adapter is being removed, so this patch skips the
block/unblock and will immediately fail any commands that
happen to make it to queuecommand while the adapter is
being shutdown.
Signed-off-by: Brian King <brking@linux.vnet.ibm.com>
Signed-off-by: Wen Xiong <wenxiong@linux.vnet.ibm.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Fnic Trace utility is a tracing functionality built directly into fnic driver
to trace events. The benefit that trace buffer brings to fnic driver is the
ability to see what it happening inside the fnic driver. It also provides the
capability to trace every IO event inside fnic driver to debug panics, hangs
and potentially IO corruption issues. This feature makes it easy to find
problems in fnic driver and it also helps in tracking down strange bugs in a
more manageable way. Trace buffer is shared across all fnic instances for
this implementation.
Signed-off-by: Hiral Patel <hiralpat@cisco.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Added new fnic debug flags for identifying IO state at every stage of IO while
debugging and also added more log messages for better debugging capability.
Signed-off-by: Sesidhar Baddela <sebaddel@cisco.com>
Signed-off-by: Hiral Patel <hiralpat@cisco.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
The issue was observed when LUN Reset is issued through IOCTL or sg_reset
utility.
fnic driver issues LUN RESET to firmware. On successful completion of device
reset, driver cleans up all the pending IOs that were issued prior to device
reset. These pending IOs are expected to be in ABTS_PENDING state. This works
fine, when the device reset operation resulted from midlayer, but not when
device reset was triggered from IOCTL path as the pending IOs were not in
ABTS_PENDING state. execution path hits panic if the pending IO is not in
ABTS_PENDING state.
Changes:
The fix replaces BUG_ON check in fnic_clean_pending_aborts() with marking
pending IOs as ABTS_PENDING if they were not in ABTS_PENDING state and skips
if they were already in ABTS_PENDING state. An extra check is added to validate
the abort status of the commands after a delay of 2 * E_D_TOV using a
helper function. The helper function returns 1 if it finds any pending IO in
ABTS_PENDING state, belong to the LUN on which device reset was issued else 0.
With this, device reset operation returns success only if the helper funciton
returns 0, otherwise it returns failure.
Other changes:
- Removed code in fnic_clean_pending_aborts() that returns failure if it finds
io_req NULL, instead of returning failure added code to continue with next io
- Added device reset flags for debugging in fnic_terminate_rport_io,
fnic_rport_exch_reset, and fnic_clean_pending_aborts
Signed-off-by: Narsimhulu Musini <nmusini@cisco.com>
Signed-off-by: Hiral Patel <hiralpat@cisco.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Driver allows IOs with more SGEs than max SGEs supported by Palo. The current
max SGEs supported by the fnic driver is 1024. The current register settings
on Palo supports a max of 256 only. Palo would return any IO with more than
256 SGEs with an error indicating INVALID_SGLS. Fnic driver should limit the
max supported SGLs in the driver to 256 to avoid this error.
Signed-off-by: Sesidhar Baddela <sebaddel@cisco.com>
Signed-off-by: Hiral Patel <hiralpat@cisco.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
1. Handling overlapped firmware resets
This fix serialize multiple firmware resets to avoid situation where fnic
device fails to come up for link up event, when firmware resets are issued
back to back. If there are overlapped firmware resets are issued,
the firmware reset operation checks whether there is any firmware reset in
progress, if so it polls for its completion in a loop with 100ms delay.
2. Handling device reset timeout
fnic_device_reset code has been modified to handle Device reset timeout:
- Issue terminate on device reset timeout.
- Introduced flags field (one of the scratch fields in scsi_cmnd).
With this, device reset request would have DEVICE_RESET flag set for other
routines to determine the type of the request.
Also modified fnic_terminate_rport_io, fnic_rport_exch_rset, completion
routines to handle SCSI commands with DEVICE_RESET flag.
3. LUN/Device Reset hangs when issued through IOCTL using utilities like
sg_reset.
Each SCSI command is associated with a valid tag, fnic uses this tag to
retrieve associated scsi command on completion. the LUN/Device Reset issued
through IOCTL resulting into a SCSI command that is not associated with a
valid tag. So fnic fails to retrieve associated scsi command on completion,
which causes hang. This fix allocates tag, associates it with the
scsi command and frees the tag, when the operation completed.
4. Preventing IOs during firmware reset.
Current fnic implementation allows IO submissions during firmware reset.
This fix synchronizes IO submissions and firmware reset operations.
It ensures that IOs issued to fnic prior to reset will be issued to the
firmware before firmware reset.
Signed-off-by: Narsimhulu Musini <nmusini@cisco.com>
Signed-off-by: Hiral Patel <hiralpat@cisco.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
All memory regions are allocated based on variables total_len
and alignment but free was based on element_size.
Signed-off-by: Sakthivel K <DL.Team.PMC.SPC.Linux.open.source@pmcs.com>
Signed-off-by: Anand Kumar S <DL.Team.PMC.SPC.Linux.open.source@pmcs.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
This patch updates the megaraid_sas driver version and updates
Documentation/scsi/ChangeLog.megaraid_sas.
Signed-off-by: Adam Radford <aradford@gmail.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
The following patch for megaraid_sas will fix an issue where the
driver should not be loading the DevHandle unless FastPath is enabled.
If FastPath was not enabled, this means the hardware raid map
validation failed for some reason, or the map was corrupted, which
could mean the DevHandle could be invalid.
Signed-off-by: Adam Radford <aradford@gmail.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
The following patch for megaraid_sas will allow Fastpath T10PI/DIF
frame builds to work with 4k sector size.
Signed-off-by: Adam Radford <aradford@gmail.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Wait for the IDC complete AEN before returning the loopback operation back to
the application to make sure the port is put back into normal operations.
Signed-off-by: Chad Dupuis <chad.dupuis@qlogic.com>
Signed-off-by: Saurav Kashyap <saurav.kashyap@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Give priority to I2C thermal.
Signed-off-by: Joe Carnuccio <joe.carnuccio@qlogic.com>
Signed-off-by: Saurav Kashyap <saurav.kashyap@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Currently,the driver is processes RSCNs for each new NPIV ports that is created.
Processing the RSCN includes a name server query to see what has changed at the
name server side. The name server query is performed by the physical port and
each virtual port on the physical adapter (since the RSCN is passed to each
virtual port for processing). As the number of virtual ports being created
increases, this causes a lot of traffic and busies the firmware.
Processing the RSCN for a virtual port we already have a priori knowledge of is
not necessary so check the 24-bit fabric ID of the RSCN entry and skip
processing it if the RSCN is for a virtual port we already know about.
Signed-off-by: Chad Dupuis <chad.dupuis@qlogic.com>
Signed-off-by: Saurav Kashyap <saurav.kashyap@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Code in qla24xx_report_id_acquisition() incorrectly assumed that
upon completion of list iteration (with no match), the 'pos'
(vp) variable passed to list_for_each_entry() would be set to
NULL. In this context, if the firmware were to return an
unrecognized vp_idx, the follow-on assignments to vp-members
could result in corruption of the structure.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: Saurav Kashyap <saurav.kashyap@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Compiling qla_gs.o (part of the qla2xxx module) triggers two GCC
warnings:
drivers/scsi/qla2xxx/qla_gs.c: In function ‘qla2x00_fdmi_rhba’:
drivers/scsi/qla2xxx/qla_gs.c:1339:7: warning: array subscript is above array bounds [-Warray-bounds]
drivers/scsi/qla2xxx/qla_gs.c: In function ‘qla2x00_fdmi_register’:
drivers/scsi/qla2xxx/qla_gs.c:1663:15: warning: array subscript is above array bounds [-Warray-bounds]
It seems that the sequence of a strcpy followed by a strlen confuses GCC
when it is keeping track of array bounds here. (It is not clear to me
which array triggers this warning and by how much GCC thinks the
subscript is above its bounds. Neither is it clear to me why comparable
code in these two functions doesn't trigger this warning.)
An easy way to silence these warnings is to use preprocessor macros and
strncpy, as that apparently gives GCC enough information to keep track
of array bounds.
Signed-off-by: Paul Bolle <pebolle@tiscali.nl>
Signed-off-by: Saurav Kashyap <saurav.kashyap@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
If we need to do a chip reset because of a serious loopback error don't try to
reset the loopback mode on the port as the mailbox command will timeout.
Signed-off-by: Chad Dupuis <chad.dupuis@qlogic.com>
Signed-off-by: Saurav Kashyap <saurav.kashyap@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Add the following error handling for loopback diagnostic mode with ISP83xx:
1. If we do not receive an MBA_DCBX_COMPLETE after our initial set port
configuration command, try to reset the port back into normal operation.
If that fails, take a FCoE dump and then reset the chip.
2. After completing the loopback diagnostic operation, if the reset of the port
back into normal operation fails then reset the port so we take a FCoE dump
and then reset the chip.
3. When we receive an IDC notification and the requested operation is loopback
extend the loop down timer so the link does not appear to down for an
extended period of time.
[jejb: fix checkpatch issue]
Signed-off-by: Chad Dupuis <chad.dupuis@qlogic.com>
Signed-off-by: Saurav Kashyap <saurav.kashyap@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
BSG code path increments ref count in the send path, but does not
decrement in the return path leading to hang during unload of the
driver.
Signed-off-by: Chad Dupuis <chad.dupuis@qlogic.com>
Signed-off-by: Saurav Kashyap <saurav.kashyap@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
To avoid continually doing ISP resets when get loop id fails to
obtain the adapter loop id, first try to do a link initialization.
Signed-off-by: Joe Carnuccio <joe.carnuccio@qlogic.com>
Signed-off-by: Saurav Kashyap <saurav.kashyap@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
If another function on the port has initiated a loopback operation do not
process the current request.
Signed-off-by: Chad Dupuis <chad.dupuis@qlogic.com>
Signed-off-by: Saurav Kashyap <saurav.kashyap@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
When the Read SFP mailbox command fails on the thermal device,
print a message explaining that thermal is not supported.
Signed-off-by: Joe Carnuccio <joe.carnuccio@qlogic.com>
Signed-off-by: Saurav Kashyap <saurav.kashyap@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
There's a subtle race in the loop/bus-reset handling whereby a
VHA's loop-state can get incorrectly set to 'down' after the
loop-reset and firmware's completion of link re-negotiation. The
original code incorrectly assumes that firmware AENs would arrive
only after mailbox-command execution to initiate the link-flap.
Here's a good case with the old code (AENs arrive after
mailbox-command completion):
qla2xxx [0000:03:00.1]-8012:91: BUS RESET ISSUED nexus=91:0:4.
qla2xxx [0000:03:00.1]-287d:91: FCPort state transitioned from ONLINE to LOST - portid=010100.
qla2xxx [0000:03:00.1]-580e:91: Asynchronous P2P MODE received.
qla2xxx [0000:03:00.1]-287d:91: FCPort state transitioned from ONLINE to LOST - portid=010400.
qla2xxx [0000:03:00.1]-802b:91: BUS RESET SUCCEEDED nexus=91:0:4.
qla2xxx [0000:03:00.1]-480b:91: Reset marker scheduled.
qla2xxx [0000:03:00.1]-5812:91: Port database changed ffff 0006 0000.
qla2xxx [0000:03:00.1]-505f:91: Link is operational (4 Gbps).
qla2xxx [0000:03:00.1]-480c:91: Reset marker end.
qla2xxx [0000:03:00.1]-480f:91: Loop resync scheduled.
qla2xxx [0000:03:00.1]-8837:91: F/W Ready - OK.
qla2xxx [0000:03:00.1]-883a:91: fw_state=3 (7, 0, 0, 0) curr time=170b8f315.
qla2xxx [0000:03:00.1]-280e:91: HBA in F P2P topology.
qla2xxx [0000:03:00.1]-2812:91: qla2x00_configure_hba success
qla2xxx [0000:03:00.1]-2814:91: Configure loop -- dpc flags = 0x5260.
notice how the 'Port database changed' (8014) arrived after the
bus-reset handler completed 'BUS RESET SUCCEEDED'.
Now, here's a failing case with the old code (AENs arrive before
mailbox-command completion):
qla2xxx [0000:03:00.1]-8012:91: BUS RESET ISSUED nexus=91:0:0.
qla2xxx [0000:03:00.1]-580e:91: Asynchronous P2P MODE received.
qla2xxx [0000:03:00.1]-287d:91: FCPort state transitioned from ONLINE to LOST - portid=010100.
qla2xxx [0000:03:00.1]-287d:91: FCPort state transitioned from ONLINE to LOST - portid=010400.
qla2xxx [0000:03:00.1]-4800:91: DPC handler sleeping.
qla2xxx [0000:03:00.1]-5812:91: Port database changed ffff 0006 0000.
qla2xxx [0000:03:00.1]-505f:91: Link is operational (4 Gbps).
qla2xxx [0000:03:00.1]-802b:91: BUS RESET SUCCEEDED nexus=91:0:0.
qla2xxx [0000:03:00.1]-480b:91: Reset marker scheduled.
qla2xxx [0000:03:00.1]-480c:91: Reset marker end.
qla2xxx [0000:03:00.1]-480f:91: Loop resync scheduled.
qla2xxx [0000:03:00.1]-8837:91: F/W Ready - OK.
qla2xxx [0000:03:00.1]-883a:91: fw_state=3 (7, 0, 0, 0) curr time=170be9eb2.
qla2xxx [0000:03:00.1]-280e:91: HBA in F P2P topology.
qla2xxx [0000:03:00.1]-2812:91: qla2x00_configure_hba success
qla2xxx [0000:03:00.1]-2814:91: Configure loop -- dpc flags = 0x5260.
qla2xxx [0000:03:00.1]-281e:91: Needs RSCN update and loop transition.
qla2xxx [0000:03:00.1]-286a:91: qla2x00_configure_loop *** FAILED ***.
qla2xxx [0000:03:00.1]-4810:91: Loop resync end.
qla2xxx [0000:03:00.1]-4800:91: DPC handler sleeping.
This race would ultimately lead to devices go unexpectedly
offline until another link-flap or chip-reset would cause driver
re-discovery to take place.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: Saurav Kashyap <saurav.kashyap@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Base the number of outstanding requests the driver will keep track of on the
available resources instead of being hard-coded.
Signed-off-by: Chad Dupuis <chad.dupuis@qlogic.com>
Signed-off-by: Saurav Kashyap <saurav.kashyap@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
There wasn't any error handling for this kzalloc().
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Boaz Harrosh <bharrosh@panasas.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
The error path calls dma_pool_free() on this path but "chap_table" is
NULL and "chap_dma" is uninitialized. It's cleaner to just return
directly.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Root cause is libsas will clear asd_sas_port phy_mask value in sas_port_deform
after triggering destruct workqueue, but the workqueue will send sync cmd and
still need phy_mask value. Now, mvsas using asd_sas_phy setting instead of
asd_sas_port setting.
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Pull trivial tree from Jiri Kosina:
"Assorted tiny fixes queued in trivial tree"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial: (22 commits)
DocBook: update EXPORT_SYMBOL entry to point at export.h
Documentation: update top level 00-INDEX file with new additions
ARM: at91/ide: remove unsused at91-ide Kconfig entry
percpu_counter.h: comment code for better readability
x86, efi: fix comment typo in head_32.S
IB: cxgb3: delay freeing mem untill entirely done with it
net: mvneta: remove unneeded version.h include
time: x86: report_lost_ticks doesn't exist any more
pcmcia: avoid static analysis complaint about use-after-free
fs/jfs: Fix typo in comment : 'how may' -> 'how many'
of: add missing documentation for of_platform_populate()
btrfs: remove unnecessary cur_trans set before goto loop in join_transaction
sound: soc: Fix typo in sound/codecs
treewide: Fix typo in various drivers
btrfs: fix comment typos
Update ibmvscsi module name in Kconfig.
powerpc: fix typo (utilties -> utilities)
of: fix spelling mistake in comment
h8300: Fix home page URL in h8300/README
xtensa: Fix home page URL in Kconfig
...
Here's the big char/misc driver patches for 3.9-rc1.
Nothing major here, just lots of different driver updates (mei, hyperv, ipack,
extcon, vmci, etc.).
All of these have been in the linux-next tree for a while.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.19 (GNU/Linux)
iEYEABECAAYFAlEmZJgACgkQMUfUDdst+ymhZgCgo2dn37r9uMCwgTSpxSq92Je5
x8kAnRF1UnD6ZvySRIlLUBV5LW1YgFnK
=i5HH
-----END PGP SIGNATURE-----
Merge tag 'char-misc-3.9-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc
Pull char/misc driver patches from Greg Kroah-Hartman:
"Here's the big char/misc driver patches for 3.9-rc1.
Nothing major here, just lots of different driver updates (mei,
hyperv, ipack, extcon, vmci, etc.).
All of these have been in the linux-next tree for a while."
* tag 'char-misc-3.9-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc: (209 commits)
w1: w1_therm: Add force-pullup option for "broken" sensors
w1: ds2482: Added 1-Wire pull-up support to the driver
vme: add missing put_device() after device_register() fails
extcon: max8997: Use workqueue to check cable state after completing boot of platform
extcon: max8997: Set default UART/USB path on probe
extcon: max8997: Consolidate duplicate code for checking ADC/CHG cable type
extcon: max8997: Set default of ADC debounce time during initialization
extcon: max8997: Remove duplicate code related to set H/W line path
extcon: max8997: Move defined constant to header file
extcon: max77693: Make max77693_extcon_cable static
extcon: max8997: Remove unreachable code
extcon: max8997: Make max8997_extcon_cable static
extcon: max77693: Remove unnecessary goto statement to improve readability
extcon: max77693: Convert to devm_input_allocate_device()
extcon: gpio: Rename filename of extcon-gpio.c according to kernel naming style
CREDITS: update email and address of Harald Hoyer
extcon: arizona: Use MICDET for final microphone identification
extcon: arizona: Always take the first HPDET reading as the final one
extcon: arizona: Clear _trig_sts bits after jack detection
extcon: arizona: Don't HPDET magic when headphones are enabled
...
Here is the big driver core merge for 3.9-rc1
There are two major series here, both of which touch lots of drivers all
over the kernel, and will cause you some merge conflicts:
- add a new function called devm_ioremap_resource() to properly be
able to check return values.
- remove CONFIG_EXPERIMENTAL
If you need me to provide a merged tree to handle these resolutions,
please let me know.
Other than those patches, there's not much here, some minor fixes and
updates.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.19 (GNU/Linux)
iEYEABECAAYFAlEmV0cACgkQMUfUDdst+yncCQCfbmnQZju7kzWXk6PjdFuKspT9
weAAoMCzcAtEzzc4LXuUxxG/sXBVBCjW
=yWAQ
-----END PGP SIGNATURE-----
Merge tag 'driver-core-3.9-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull driver core patches from Greg Kroah-Hartman:
"Here is the big driver core merge for 3.9-rc1
There are two major series here, both of which touch lots of drivers
all over the kernel, and will cause you some merge conflicts:
- add a new function called devm_ioremap_resource() to properly be
able to check return values.
- remove CONFIG_EXPERIMENTAL
Other than those patches, there's not much here, some minor fixes and
updates"
Fix up trivial conflicts
* tag 'driver-core-3.9-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core: (221 commits)
base: memory: fix soft/hard_offline_page permissions
drivercore: Fix ordering between deferred_probe and exiting initcalls
backlight: fix class_find_device() arguments
TTY: mark tty_get_device call with the proper const values
driver-core: constify data for class_find_device()
firmware: Ignore abort check when no user-helper is used
firmware: Reduce ifdef CONFIG_FW_LOADER_USER_HELPER
firmware: Make user-mode helper optional
firmware: Refactoring for splitting user-mode helper code
Driver core: treat unregistered bus_types as having no devices
watchdog: Convert to devm_ioremap_resource()
thermal: Convert to devm_ioremap_resource()
spi: Convert to devm_ioremap_resource()
power: Convert to devm_ioremap_resource()
mtd: Convert to devm_ioremap_resource()
mmc: Convert to devm_ioremap_resource()
mfd: Convert to devm_ioremap_resource()
media: Convert to devm_ioremap_resource()
iommu: Convert to devm_ioremap_resource()
drm: Convert to devm_ioremap_resource()
...
When there are multiple FCFs in the fabric, and one of them becomes
unavailable, the fabric name for the unavailable FCF becomes 0 along
with FIP_FL_AVAIL getting reset. In this case, FCF selection logic does
not select any FCF as it first checks for conflicting FCFs (since fabric
name is 0, it fails the condition), instead of first checking if it is
usable or not. Fix it by first checking if FCF is usable and skip that
FCF, and go to the next one in the list to check if it can be selected.
Signed-off-by: Bhanu Prakash Gollapudi <bprakash@broadcom.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
schedule_delayed_work() is using msec instead of jiffies. On PLOGI
reject from target, remote port retry is scheduled @ 20 sec instead
of 2sec(FC_DEF_E_D_TOV).
XenServer dom0 kernel is configured with CONFIG_HZ=100Hz
Signed-off-by: Krishna Mohan <krmohan@cisco.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
When a CVL is received while we wait to select best FCF, we drop it
without handling it. This causes initiator and the switch to go
out-of-sync. Initiator proceeds selecting one of the FCFs and tries to
send FIP FLOGI. However the switch may reject the FLOGI, as it has
cleared its internal state, and expects the initiator to start FIP
discovery protocol. Fix this condition by resetting the fcoe
controller.
Signed-off-by: Bhanu Prakash Gollapudi <bprakash@broadcom.com>
Reviewed-by: Yi Zou <yi.zou@intel.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
All in-kernel users of class_find_device() don't really need mutable
data for match callback.
In two places (kernel/power/suspend_test.c, drivers/scsi/osd/osd_uld.c)
this patch changes match callbacks to use const search data.
The const is propagated to rtc_class_open() and power_supply_get_by_name()
parameters.
Note that there's a dev reference leak in suspend_test.c that's not
touched in this patch.
Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Originally 'efi_enabled' indicated whether a kernel was booted from
EFI firmware. Over time its semantics have changed, and it now
indicates whether or not we are booted on an EFI machine with
bit-native firmware, e.g. 64-bit kernel with 64-bit firmware.
The immediate motivation for this patch is the bug report at,
https://bugs.launchpad.net/ubuntu-cdimage/+bug/1040557
which details how running a platform driver on an EFI machine that is
designed to run under BIOS can cause the machine to become
bricked. Also, the following report,
https://bugzilla.kernel.org/show_bug.cgi?id=47121
details how running said driver can also cause Machine Check
Exceptions. Drivers need a new means of detecting whether they're
running on an EFI machine, as sadly the expression,
if (!efi_enabled)
hasn't been a sufficient condition for quite some time.
Users actually want to query 'efi_enabled' for different reasons -
what they really want access to is the list of available EFI
facilities.
For instance, the x86 reboot code needs to know whether it can invoke
the ResetSystem() function provided by the EFI runtime services, while
the ACPI OSL code wants to know whether the EFI config tables were
mapped successfully. There are also checks in some of the platform
driver code to simply see if they're running on an EFI machine (which
would make it a bad idea to do BIOS-y things).
This patch is a prereq for the samsung-laptop fix patch.
Cc: David Airlie <airlied@linux.ie>
Cc: Corentin Chary <corentincj@iksaif.net>
Cc: Matthew Garrett <mjg59@srcf.ucam.org>
Cc: Dave Jiang <dave.jiang@intel.com>
Cc: Olof Johansson <olof@lixom.net>
Cc: Peter Jones <pjones@redhat.com>
Cc: Colin Ian King <colin.king@canonical.com>
Cc: Steve Langasek <steve.langasek@canonical.com>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Konrad Rzeszutek Wilk <konrad@kernel.org>
Cc: Rafael J. Wysocki <rjw@sisk.pl>
Cc: <stable@vger.kernel.org>
Signed-off-by: Matt Fleming <matt.fleming@intel.com>
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
Delete successive tests to the same location. The code tested the result
of a previous allocation, that itself was already tested. It is changed to
test the result of the most recent allocation.
A simplified version of the semantic match that finds this problem is as
follows: (http://coccinelle.lip6.fr/)
// <smpl>
@s exists@
local idexpression y;
expression x,e;
@@
*if ( \(x == NULL\|IS_ERR(x)\|y != 0\) )
{ ... when forall
return ...; }
... when != \(y = e\|y += e\|y -= e\|y |= e\|y &= e\|y++\|y--\|&y\)
when != \(XT_GETPAGE(...,y)\|WMI_CMD_BUF(...)\)
*if ( \(x == NULL\|IS_ERR(x)\|y != 0\) )
{ ... when forall
return ...; }
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Acked-by: Bhanu Prakash Gollapudi <bprakash@broadcom.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
While reading sysfs chap_in_idx and chap_out_idx attribute, if chap
authentication is not set we get an error as "Invalid argument".
Signed-off-by: Manish Rangankar <manish.rangankar@qlogic.com>
Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Boot from SAN fails in some cases where boot target login response
is slow. In this case, probe finishes early and triggers init, which
doesn't find remote disk to mount root which leads to BFS failure.
Signed-off-by: Manish Rangankar <manish.rangankar@qlogic.com>
Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
This patch force driver to collect firmware dump using following command:-
"echo 2 > /sys/class/scsi_host/hostX/device/fw_dump"
Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Problem:
If initialization of adapter fails for some reason, then the interrupt handlers
are released. The interrupt handlers are not registered again when initialization
of adapter is retried.
Solution:
Re-register the interrupt handler when adapter initialization is retried.
Signed-off-by: Poornima Vonti <poornima.vonti@qlogic.com>
Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Problem:
QLA4xxx firmware may assert if given more IOCBs than it can handle.
Solution:
The driver was updated to throttle the number of active IOCBs based
on the total number of IOCB buffers received from get_firmware_status
mbx_sts[2].
Signed-off-by: Karen Higgins <karen.higgins@qlogic.com>
Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Removed unnecessary calls to qla4xxx_get_firmware_status from
function qla4xxx_init_local_data
Signed-off-by: Karen Higgins <karen.higgins@qlogic.com>
Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Quiesce all different activities performed by driver upon the link events
while loopback diagnostics is in progress.
Signed-off-by: Nilesh Javali <nilesh.javali@qlogic.com>
Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
The spurious interrupt messages are seen when interrupt lines are
shared between different adapters or modules. Example, interrupt
lines are shared between qlcnic and qla4xxx and USB modules, then the
console is flooded with flurry of spurious interrupt messages
which are expected in such scenario.
Hence put these messages under debug level 2 for INTx interrupt mode.
Signed-off-by: Nilesh Javali <nilesh.javali@qlogic.com>
Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
When doing a hotplug remove of a cxgb4 device, there are still dandling
symlinks at /sys/class/scsi_host/hostX to the removed PCI device. The
upper layer device may also try to send data, which may crash the
system.
The DETACH message from the lower level driver is sent to the ULD when
the device is removed, when the scsi host should be removed from the
system, avoiding any problems.
After this patch, there are no more dangling symlinks and many attempts
to crash the system while there is SCSI activity and removing the device
have failed. Adding the device back again works as expected, with the
scsi hosts showing up again.
Based on a patch by Karen Xie.
Signed-off-by: Thadeu Lima de Souza Cascardo <cascardo@linux.vnet.ibm.com>
Cc: Karen Xie <kxie@chelsio.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
The closing parenthesis is in the wrong place so it takes the sizeof a
pointer instead of the sizeof the buffer minus one.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Anil Gurumurthy <agurumur@brocade.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Check mbox_sts[3] instead of mbox_sts[4] for ISP83xx to validate size
of data returned
Signed-off-by: Nilesh Javali <nilesh.javali@qlogic.com>
Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Fixed no-context ABTS received on unsolicited receive queue failed with BA_RJT
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Removed use of NOP mailboxes for interrupt verification in pci_probe_one_s4
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
This patch fixes the following sparse error:
CHECK drivers/scsi/ipr.c
spinlock.h:147:9: warning: context imbalance in 'ipr_reset_reload' - unexpected unlock
Signed-off-by: Wen Xiong <wenxiong@linux.vnet.ibm.com>
Acked-by: Brian King <brking@linux.vnet.ibm.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Signed-off-by: Wen Xiong <wenxiong@linux.vnet.ibm.com>
Acked-by: Brian King <brking@linux.vnet.ibm.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
This patch implements blk iopoll in ipr driver for performance improvement.
Signed-off-by: Wen Xiong <wenxiong@linux.vnet.ibm.com>
Acked-by: Brian King <brking@linux.vnet.ibm.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
This patch reduces lock contention while implementing distributed
completion processing.
Signed-off-by: Wen Xiong <wenxiong@linux.vnet.ibm.com>
Acked-by: Brian King <brking@linux.vnet.ibm.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
The new generation IBM SAS Controllers will support MSI-X interrupts and
Distributed Completion Processing features. This patch add these support
in ipr device driver.
Signed-off-by: Wen Xiong <wenxiong@linux.vnet.ibm.com>
Acked-by: Brian King <brking@linux.vnet.ibm.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
The resource path as displayed by the ipr driver is the
location string identifying a location on the SAS fabric.
This patch adds the SCSI host number such that error logs
can be more easily correlated in multiple adapter configurations.
Signed-off-by: Brian King <brking@linux.vnet.ibm.com>
Signed-off-by: Wen Xiong <wenxiong@linux.vnet.ibm.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Add the appropriate definitions and table entries for new adapter support.
Signed-off-by: Wen Xiong <wenxiong@linux.vnet.ibm.com>
Acked-by: Brian King <brking@linux.vnet.ibm.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
If kzalloc() or csio_hw_check_fwconfig() fail we may leave the
csio_hw_flash_config() function without freeing allocated memory or
firmware. This should take care of the leaks.
Signed-off-by: Jesper Juhl <jj@chaosbits.net>
Acked-by: Naresh Kumar Inna <naresh@chelsio.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Increase max_sectors from 512 to 1024 in order to support max IO size of 512KB.
Signed-off-by: Bhanu Prakash Gollapudi <bprakash@broadcom.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Since the FW counters are 32-bit, accumulate the stats in the driver.
[jejb: fix checkpatch warning]
Signed-off-by: Bhanu Prakash Gollapudi <bprakash@broadcom.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
We used to map doorbell register after FW enable request is complete.
This causes a race condition when unsolicited event is received, and FW
sends a CQE for it. Since the doorbell is not mapped, driver does not
arm CQ, which means FW will not notify the driver for further CQ
completions. To resolve this, map the doorbell between offload and
enable, so that driver is ready to receive the unsolicited packets and
arm the CQ as soon as FW enable is performed.
Signed-off-by: Bhanu Prakash Gollapudi <bprakash@broadcom.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Moved the 'waiting for upload/offload completion' logic to respective
functions as it is called in multiple places. Also this is done in
preperation for the next patch.
Signed-off-by: Bhanu Prakash Gollapudi <bprakash@broadcom.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Software FCoE target always advertises RETRY bit even when there are no
tape LUNs behind the target. This causes the driver to enable FW support
for sequence level error recovery and perform REC/SRR. This patch
arrests the behavior by not enabling SLER feature for this target.
Signed-off-by: Bhanu Prakash Gollapudi <bprakash@broadcom.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
If the NULL test is necessary, the initialization involving a dereference of
the tested value should be moved after the NULL test.
The sematic patch that fixes this problem is as follows:
(http://coccinelle.lip6.fr/)
// <smpl>
@@
type T;
expression E;
identifier i,fld;
statement S;
@@
- T i = E->fld;
+ T i;
... when != E
when != i
if (E == NULL) S
+ i = E->fld;
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Bhanu Prakash Gollapudi <bprakash@broadcom.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
These calls are followed by calls to memcpy() on the same memory area, so they
can be safely removed.
Signed-off-by: Cyril Roelandt <tipecaml@gmail.com>
Signed-off-by: Bhanu Prakash Gollapudi <bprakash@broadcom.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
This patch stops the driver to invoke kthread (which remove the dead ioc)
for some time while EEH recovery has started.
[thenzl: add a 'non_operational_loop' reset.]
Signed-off-by: Sreekanth Reddy <Sreekanth.Reddy@lsi.com>
Signed-off-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
The variable 'chain_flags' and 'phy_number' are initialized but never used
otherwise, So remove those unused variables.
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: Sreekanth Reddy <Sreekanth.Reddy@lsi.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Sreekanth Reddy