The previous patch fixed spurious read faults from occuring by copying
the data if we happen to have a single block at the end of a page. It
appears that gcc cannot guarantee 16-byte alignment in the kernel with
__attribute__. The following report from Torben Viets shows a buffer
that's only 8-byte aligned:
> eneral protection fault: 0000 [#1]
> Modules linked in: xt_TCPMSS xt_tcpmss iptable_mangle ipt_MASQUERADE
> xt_tcpudp xt_mark xt_state iptable_nat nf_nat nf_conntrack_ipv4
> iptable_filter ip_tables x_tables pppoe pppox af_packet ppp_generic slhc
> aes_i586
> CPU: 0
> EIP: 0060:[<c035b828>] Not tainted VLI
> EFLAGS: 00010292 (2.6.23.12 #7)
> EIP is at aes_crypt_copy+0x28/0x40
> eax: f7639ff0 ebx: f6c24050 ecx: 00000001 edx: f6c24030
> esi: f7e89dc8 edi: f7639ff0 ebp: 00010000 esp: f7e89dc8
Since the hardware must have 16-byte alignment, the following patch fixes
this by open coding the alignment adjustment.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
The xcryptecb instruction always processes an even number of blocks so
we need to ensure th existence of an extra block if we have to process
an odd number of blocks.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
* 'master' of master.kernel.org:/pub/scm/linux/kernel/git/davem/net-2.6:
[NETFILTER]: Fix NULL pointer dereference in nf_nat_move_storage()
[SUNHME]: VLAN support for sunhme
[CHELSIO]: Fix skb->dev setting.
[NETFILTER]: fix compat_nf_sockopt typo
[INET]: Fix potential kfree on vmalloc-ed area of request_sock_queue
[VIA_VELOCITY]: Don't oops on MTU change.
iwl4965: fix not correctly dealing with hotunplug
rt2x00: Fix chipset revision validation
iwl3945: place CCK rates in front of OFDM for supported rates
mac80211: Fix queuing of scan containing a SSID
This patch enables VLAN support on sunhme by increasing BMAC_TXMAX/BMAC_RXMAX
and allocating extra space via skb_put for the VLAN header.
Signed-off-by: Chris Poon <dev-null@telus.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
eth_type_trans() now sets skb->dev. Access skb->def after it gets
set.
Signed-off-by: Divy Le Ray <divy@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
* 'i2c-for-linus' of git://jdelvare.pck.nerim.net/jdelvare-2.6:
i2c/eeprom: Recognize VGN as a valid Sony Vaio name prefix
i2c/eeprom: Hide Sony Vaio serial numbers
i2c-pasemi: Fix NACK detection
i2c-pasemi: Replace obsolete "driverfs" reference with "sysfs"
i2c: Make i2c_check_addr static
i2c-dev: Unbound new-style i2c clients aren't busy
i2c-dev: "how does it work" comments
Recent (i.e. 2005 and later) Sony Vaio laptops have names beginning
with VGN rather than PCG. Update the eeprom driver so that it
recognizes these.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
The sysfs interface to DMI data takes care to not make the system
serial number and UUID world-readable, presumably due to privacy
concerns. For consistency, we should not let the eeprom driver
export these same strings to the world on Sony Vaio laptops.
Instead, only make them readable by root, as we already do for BIOS
passwords.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Turns out we don't actually check the status to see if there was a
device out there to talk to, just if we had a timeout when doing so.
Add the proper check, so we don't falsly think there are devices
on the bus that are not there, etc.
Signed-off-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
i2c_check_addr is only used inside i2c-core now, so we can make it
static and stop exporting it. Thanks to David Brownell for noticing.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Let i2c-dev deal properly with new-style i2c clients. Instead of
considering them always busy, it needs to check wether a driver is
bound to them or not.
This is still not completely correct, as the client could become
busy later, but the same problem already existed before new-style
clients were introduced. We'll want to fix it someday.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: David Brownell <dbrownell@users.sourceforge.net>
This adds some "how does this work" comments to the i2c-dev driver,
plus separators between the three main components:
- The parallel list of i2c_adapters ("i2c_dev_list"), each of which
gets a "struct i2c_dev" and a /dev/i2c-X character special file.
- An i2cdev_driver gets adapter add/remove notifications, which are
used to maintain that list of adapters.
- Special file operations, which let userspace talk either directly to
the adapter (for i2c_msg operations) or through cached addressing info
using an anonymous i2c_client (never registered anywhere).
Plus there's the usual module load/unload record keeping.
After making sense of this code, I think that the anonymous i2c_client
is pretty shady. But since it's never registered, using this code with
a system set up for "new style" I2C drivers is no more complicated than
always using the I2C_SLAVE_FORCE ioctl (instead of I2C_SLAVE).
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
This reverts commit 7fb7ac2411.
Heikki Orsila reports that it causes a regression:
"Doing
nc host port < /dev/zero
on a sending machine (not skge) to an skge machine that is receiving:
nc -l -p port >/dev/null
with ~60 MiB/s speed, causes the interface go malfunct. A slow
transfer doesn't cause a problem."
See
http://bugzilla.kernel.org/show_bug.cgi?id=9321
for some more information.
There is a workaround (also reported by Heikki):
"After some fiddling, I noticed that not changing the register write
order on patch:
+ skge_write32(hw, RB_ADDR(q, RB_END), end);
skge_write32(hw, RB_ADDR(q, RB_WP), start);
skge_write32(hw, RB_ADDR(q, RB_RP), start);
- skge_write32(hw, RB_ADDR(q, RB_END), end);
fixes the visible effect.. Possibly not the root cause of the
problem, but changing the order back fixes networking here."
but that has yet to be ack'ed or tested more widely, so the whole
problem-causing commit gets reverted until this is resolved properly.
Bisected-and-requested-by: Heikki Orsila <shdl@zakalwe.fi>
Cc: Stephen Hemminger <shemminger@linux-foundation.org>
Cc: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Simple mtu change when device is down.
Fix http://bugzilla.kernel.org/show_bug.cgi?id=9382.
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband:
mlx4_core: Fix thinko in QP destroy (incorrect bitmap_free)
RDMA/cxgb3: Set the max_qp_init_rd_atom attribute in query_device
IB/ehca: Fix static rate calculation
IB/ehca: Return physical link information in query_port()
IB/ipath: Fix race with ACK retry timeout list management
IB/ipath: Fix memory leak in ipath_resize_cq() if copy_to_user() fails
mlx4_core: Fix possible bad free in mlx4_buf_free()
* 'master' of master.kernel.org:/pub/scm/linux/kernel/git/davem/net-2.6:
[NET]: rt_check_expire() can take a long time, add a cond_resched()
[ISDN] sc: Really, really fix warning
[ISDN] sc: Fix sndpkt to have the correct number of arguments
[TCP] FRTO: Clear frto_highmark only after process_frto that uses it
[NET]: Remove notifier block from chain when register_netdevice_notifier fails
[FS_ENET]: Fix module build.
[TCP]: Make sure write_queue_from does not begin with NULL ptr
[TCP]: Fix size calculation in sk_stream_alloc_pskb
[S2IO]: Fixed memory leak when MSI-X vector allocation fails
[BONDING]: Fix resource use after free
[SYSCTL]: Fix warning for token-ring from sysctl checker
[NET] random : secure_tcp_sequence_number should not assume CONFIG_KTIME_SCALAR
[IWLWIFI]: Not correctly dealing with hotunplug.
[TCP] FRTO: Plug potential LOST-bit leak
[TCP] FRTO: Limit snd_cwnd if TCP was application limited
[E1000]: Fix schedule while atomic when called from mii-tool.
[NETX]: Fix build failure added by 2.6.24 statistics cleanup.
[EP93xx_ETH]: Build fix after 2.6.24 NAPI changes.
[PKT_SCHED]: Check subqueue status before calling hard_start_xmit
Declare mac using DECLARE_MAC_BUF for use when calling print_mac().
This fixes compile error where mac was undeclared.
Also, remove unused variable i.
Signed-off-by: Jesper Nilsson <jesper.nilsson@axis.com>
Cc: Mikael Starvik <mikael.starvik@axis.com>
Cc: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
New and improved serial driver for CRISv10, take three, with improvements
suggested by Jiri Slaby.
- Call wait_event_interruptible with a _correct_ and sensible condition.
- Removed superfluous test of info->flags & ASYNC_CLOSING, since that is done
by wait_event_interruptible.
- Moved common code for deregistering DMA and IRQ to deinit_port function.
- Use setup_timer when initializing flush_timer.
- Convert bit-field for uses_dma_in and uses_dma_out to regular bytes.
- Removed CVS tags.
- Removed defines and comments for CRIS_BUF_SIZE and TTY_THRESHOLD_THROTTLE
(no longer used).
- Cleaned up code to pass checkpatch.
- Add crisv10.h header file.
- Merge of CRISv10 from Axis internal CVS.
Signed-off-by: Jesper Nilsson <jesper.nilsson@axis.com>
Reviewed-by: Jiri Slaby <jirislaby@gmail.com>
Cc: Mikael Starvik <starvik@axis.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
New (updated) version of ethernet driver for cris v10.
- First steps to simplify and make the MII code more similar
between the etrax100 and etraxfs ports.
- Start the transmit queue before enabling tx interrupts
to avoid race with the first frame.
- Flip the comparition statement to stick to physical addresses
to avoid phys_to_virt mapping a potential null pointer.
This was not an error but the change simplifies debugging
of address-space mappings.
- Made myPrevRxDesc local to e100_rx since it was only used there.
Fixed out of memory handling in e100_rx. If dev_alloc_skb() fails
persistently the system is hosed anyway but at least it won't
loop in an interrupt handler.
- Correct some code formatting issues.
- Add defines SET_ETH_ENABLE_LEDS, SET_ETH_DISABLE_LEDS
and SET_ETH_AUTONEG used in new cris v10 ethernet driver.
Signed-off-by: Jesper Nilsson <jesper.nilsson@axis.com>
Acked-by: Mikael Starvik <starvik@axis.com>
Cc: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
arm:
drivers/scsi/aic94xx/aic94xx_sds.c:381:1: warning: "FLASH_SIZE" redefined
In file included from include/asm/arch/irqs.h:22,
from include/asm/irq.h:4,
from include/asm/hardirq.h:6,
from include/linux/hardirq.h:7,
from include/asm-generic/local.h:5,
from include/asm/local.h:1,
from include/linux/module.h:19,
from include/linux/device.h:21,
from include/linux/pci.h:52,
from drivers/scsi/aic94xx/aic94xx_sds.c:28:
include/asm/arch/platform.h:444:1: warning: this is the location of the previous definition
Cc: Gilbert Wu <gilbert_wu@adaptec.com>
Cc: James Bottomley <James.Bottomley@HansenPartnership.com>
Cc: Russell King <rmk@arm.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Remove redundant code leading to NULL ptr deref and let terminal config
settings take place in the proper initialization path in
usb_console_setup().
Signed-off-by: Borislav Petkov <bbpetkov@yahoo.de>
Cc: <lucy@keyspan.com>
Cc: Greg KH <greg@kroah.com>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Check if AC state has changed across resume and notify userspace if so.
Fixes "[2.6.24-rc1 regression] AC adapter state does not change after resume"
Signed-off-by: Alexey Starikovskiy <astarikovskiy@suse.de>
Tested-by: Andrey Borzenkov <arvidjaar@mail.ru>
Cc: Len Brown <lenb@kernel.org>
Cc: "Rafael J. Wysocki" <rjw@sisk.pl>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Do not provide /proc/acpi/ac_adapter if ACPI_PROCFS is not defined. This
eliminates duplicated power adapters in HAL and makes it consistent with
battery module
Signed-off-by: Andrey Borzenkov <arvidjaar@mail.ru>
Acked-by: Alexey Starikovskiy <astarikovskiy@suse.de>
Cc: Len Brown <lenb@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Make 'default_mode' and 'default_var' be __initdata.
Fixes these section warnings:
WARNING: vmlinux.o(.data+0x128e0): Section mismatch: reference to .init.data:default_mode_CRT (between 'default_mode' and 'default_var')
WARNING: vmlinux.o(.data+0x128e4): Section mismatch: reference to .init.data:default_var_CRT (between 'default_var' and 'dev_attr_size')
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Cc: "Antonino A. Daplas" <adaplas@pol.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
We have seen ramdisk based install systems, where some pages of mapped
libraries and programs were suddendly zeroed under memory pressure. This
should not happen, as the ramdisk avoids freeing its pages by keeping them
dirty all the time.
It turns out that there is a case, where the VM makes a ramdisk page clean,
without telling the ramdisk driver. On memory pressure shrink_zone runs
and it starts to run shrink_active_list. There is a check for
buffer_heads_over_limit, and if true, pagevec_strip is called.
pagevec_strip calls try_to_release_page. If the mapping has no releasepage
callback, try_to_free_buffers is called. try_to_free_buffers has now a
special logic for some file systems to make a dirty page clean, if all
buffers are clean. Thats what happened in our test case.
The simplest solution is to provide a noop-releasepage callback for the
ramdisk driver. This avoids try_to_free_buffers for ramdisk pages.
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
Acked-by: Nick Piggin <npiggin@suse.de>
Cc: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The tle62x0 driver was ignoring all read errors. This patch makes it
pass such errors up the stack, instead of returning bogus data.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
"Luming Yu" <luming.yu@gmail.com> says:
There is a "ttyS1 irq is -1" problem observed on tiger4 which cause the
serial port broken.
It is because that there is __no__ ACPI IRQ resource assigned for the
serial port. So the value of the IRQ for the port is never changed since it
got initialized to -1.
If PNP supplies a valid IRQ, use it. Otherwise, leave port.irq == 0, which
means "no IRQ" to the serial core.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Cc: Yu Luming <luming.yu@intel.com>
Acked-by: Matthew Wilcox <matthew@wil.cx>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Cc: Russell King <rmk@arm.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The i5000_edac driver's PCI registration structure has the name
""i5000_edac"" (with extra set of double-quotes) which is probably not
intentional. Get rid of __stringify.
Signed-off-by: Darrick J. Wong <djwong@us.ibm.com>
Cc: Doug Thompson <norsk5@yahoo.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Firmware like PNPBIOS or ACPI can report the address space consumed by the
RTC. The actual space consumed may be less than the size (RTC_IO_EXTENT)
assumed by the RTC driver.
The PNP core doesn't request resources yet, but I'd like to make it do so.
If/when it does, the RTC_IO_EXTENT request may fail, which prevents the RTC
driver from loading.
Since we only use the RTC index and data registers at RTC_PORT(0) and
RTC_PORT(1), we can fall back to requesting just enough space for those.
If the PNP core requests resources, this results in typical I/O port usage
like this:
0070-0073 : 00:06 <-- PNP device 00:06 responds to 70-73
0070-0071 : rtc <-- RTC driver uses only 70-71
instead of the current:
0070-0077 : rtc <-- RTC_IO_EXTENT == 8
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: David Brownell <david-b@pacbell.net>
Cc: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The misc_register() error path always released an I/O port region,
even if the region was memory-mapped (only mips uses memory-mapped RTC,
as far as I can see).
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: David Brownell <david-b@pacbell.net>
Acked-by: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add support for version 2 of the ioatdma device. This device handles
the descriptor chain and DCA services slightly differently:
- Instead of moving the dma descriptors between a busy and an idle chain,
this new version uses a single circular chain so that we don't have
rewrite the next_descriptor pointers as we add new requests, and the
device doesn't need to re-read the last descriptor.
- The new device has the DCA tags defined internally instead of needing
them defined statically.
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Cc: "Williams, Dan J" <dan.j.williams@intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
<debug output from Joel's system>
handling stripe 7629696, state=0x14 cnt=1, pd_idx=2 ops=0:0:0
check 5: state 0x6 toread 0000000000000000 read 0000000000000000 write fffff800ffcffcc0 written 0000000000000000
check 4: state 0x6 toread 0000000000000000 read 0000000000000000 write fffff800fdd4e360 written 0000000000000000
check 3: state 0x1 toread 0000000000000000 read 0000000000000000 write 0000000000000000 written 0000000000000000
check 2: state 0x1 toread 0000000000000000 read 0000000000000000 write 0000000000000000 written 0000000000000000
check 1: state 0x6 toread 0000000000000000 read 0000000000000000 write fffff800ff517e40 written 0000000000000000
check 0: state 0x6 toread 0000000000000000 read 0000000000000000 write fffff800fd4cae60 written 0000000000000000
locked=4 uptodate=2 to_read=0 to_write=4 failed=0 failed_num=0
for sector 7629696, rmw=0 rcw=0
</debug>
These blocks were prepared to be written out, but were never handled in
ops_run_biodrain(), so they remain locked forever. The operations flags
are all clear which means handle_stripe() thinks nothing else needs to be
done.
This state suggests that the STRIPE_OP_PREXOR bit was sampled 'set' when it
should not have been. This patch cleans up cases where the code looks at
sh->ops.pending when it should be looking at the consistent stack-based
snapshot of the operations flags.
Report from Joel:
Resync done. Patch fix this bug.
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Tested-by: Joel Bertrand <joel.bertrand@systella.fr>
Cc: <stable@kernel.org>
Cc: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Remove annoying build warnings about unused variables in atmel_serial,
which afflict both AT91 and AVR32 builds.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Acked-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
Cc: Andrew Victor <andrew@sanpeople.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
When a DMA device is unregistered, its reference count is decremented twice
for each channel: Once dma_class_dev_release() and once in
dma_chan_cleanup(). This may result in the DMA device driver's remove()
function completing before all channels have been cleaned up, causing lots
of use-after-free fun.
Fix it by incrementing the device's reference count twice for each
channel during registration.
[dan.j.williams@intel.com: kill unnecessary client refcounting]
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Move pci_dev_put outside the loops in which it occurs. Within the loop,
pci_dev_put is done implicitly by pci_get_device.
The problem was detected using the following semantic patch, and corrected
by hand.
@@
expression dev;
expression E;
@@
- pci_dev_put(dev)
... when != dev = E
- pci_get_device(...,dev)
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The pf driver for parallel port floppy drives seems to be broken. At least
with Imation SuperDisk with EPAT chip, the driver calls pi_connect() and
pi_disconnect after each transferred sector. At least with EPAT, this
operation is very expensive - causes drive recalibration. Thus, transferring
even a single byte (dd if=/dev/pf0 of=/dev/null bs=1 count=1) takes 20
seconds, making the driver useless.
The pf_next_buf() function seems to be broken as it returns 1 always (except
when pf_run is non-zero), causing the loop in do_pf_read_drq (and
do_pf_write_drq) to be executed only once.
The following patch fixes this problem. It also fixes swapped descriptions in
pf_lock() function and removes DBMSG macro, which seems useless.
Signed-off-by: Ondrej Zary <linux@rainbow-software.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Some error paths in txx9spi_probe wrongly return 0. This patch fixes them by
using the devres interfaces.
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Acked-by: David Brownell <david-b@pacbell.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
After 49dce689ad, device_for_each_child
iteration hits the master device itself. Do not call spi_unregister_device()
for the master device.
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Acked-by: David Brownell <david-b@pacbell.net>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Zillions of people are getting my-battery-monitor-doesnt-work problems
(including me).
Lessen the damage by making ACPI_PROCFS default to on.
Cc: Len Brown <lenb@kernel.org>
Cc: "Rafael J. Wysocki" <rjw@sisk.pl>
Acked-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The following is an extra entry to enable the touch screen on the new LG
C1 EXPRESS DUAL machine.
Cc: Russell King <rmk@arm.linux.org.uk>
Cc: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch fixes the possible usage of a negative value as an array
index spotted by the Coverity checker.
sisfb_validate_mode() could return a negative error code and we must check for
that prior to using its return value as an array index.
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Cc: Thomas Winischhofer <thomas@winischhofer.net>
Cc: "Antonino A. Daplas" <adaplas@pol.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch fixes a memory leak spotted by the Coverity checker.
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Cc: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
A relatively recent version of the Geode LX datasheet listed the wrong
address for one of the MSRs that controls TFT panels, resulting in
breakage. This patch corrects the MSR address.
Signed-off-by: Jordan Crouse <jordan.crouse@amd.com>
Cc: "Antonino A. Daplas" <adaplas@pol.net>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Attached patch fixes two compilation problems of s1d13xxxfb.c:
- Fixes outdated dbg() message to fix compilation error with debugging enabled.
- Do not read kernel command line options when compiled as module.
Signed-off-by: Stanislav Brabec <utx@penguin.cz>
Cc: "Antonino A. Daplas" <adaplas@pol.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Instruction pointer returned by profile_pc() can be a random value. This
break the assumption than we can safely set struct op_sample.eip field to a
magic value to signal to the per-cpu buffer reader side special event like
task switch ending up in a segfault in get_task_mm() when profile_pc()
return ~0UL. Fixed by sanitizing the sampled eip and reject/log invalid
eip.
Problem reported by Sami Farin, patch tested by him.
Signed-off-by: Philippe Elie <phil.el@wanadoo.fr>
Tested-by: Sami Farin <safari-kernel@safari.iki.fi>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Herbert Xu