Fixes a wrong setting of resource parameter list in
SMSC911x platform driver data structure for Overo case.
This fixes folowing warning when compiling for Overo board:
warning: initialization from incompatible pointer type
Introduced since commit id:
commit 172ef27544
Author: Steve Sakoman <sakoman@gmail.com>
Date: Mon Feb 2 06:27:49 2009 +0000
ARM: Add SMSC911X support to Overo platform (V2)
Signed-off-by: Sergio Aguirre <saaguirre@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
OMAP3EVM uses ISP1504 phy which doesn't require any programming and
thus has to use NOP otg transceiver.
Cleanups being done:
- Remove unwanted code in usb-musb.c file
- Register NOP in OMAP3EVM board file using
usb_nop_xceiv_register().
- Select NOP_USB_XCEIV for OMAP3EVM boards.
- Don't enable TWL4030_USB in omap3_evm_defconfig
Signed-off-by: Ajay Kumar Gupta <ajay.gupta@ti.com>
Signed-off-by: Eino-Ville Talvala <talvala@stanford.edu>
Acked-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Powerdomain previous state is checked after restoring new states in
suspend. This patch fixes this problem.
Signed-off-by: Jouni Hogander <jouni.hogander@nokia.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Use list_add_tail() when adding discovered UART ports. This is so
traversal using list_for_each_entry() will traverse the list in the
order they were found.
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
This patch causes the OMAP uarts to honor the sysfs power/wakeup file
for IOPAD wakeups. Before the OMAP was always woken up from off mode
on a rs232 signal change. This patch also creates a different
platform device for each serial port so that the wakeup properties can
be control per port.
By default, IOPAD wakeups are enabled for each UART. To disable,
# echo disabled > /sys/devices/platform/serial8250.0/power/wakeup
Where serial8250.0 can be replaced by .1, or .2 to control the other
ports.
Original idea and original patch from Russ Dill <russ.dill@gmail.com>
Cc: Russ Dill <russ.dill@gmail.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
It was possible for an unhandled interrupt to occur if there was incoming
serial traffic during wakeup from suspend. This was caused by the code
in arch-arm/mach-omap2/serial.c keeping interrupt enabled all the time,
but not acking its interrupts. Applies on top of PM branch.
Use the PM begin/end hooks to ensure that the "serial idle" interrupts
are disabled during the suspend path. Also, since begin/end hooks are
now used, use the suspend_state that is passed in the begin hook instead
of the enter hook as per the platform_suspend_ops docs.
Signed-off-by: Tero Kristo <tero.kristo@nokia.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Streamline the OMAP4 special IRQ assignments by putting inside
normal init loop instead of having a separate loop.
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
By default, prevent functional wakeups from inside a module from
waking up the IVA2. Let DSP Bridge code handle this when loaded.
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
This patch creates McBSP support on OMAP4430 development platform. This patch
includes corresponding base address changes for OMAP4.
Signed-off-by: Syed Rafiuddin <rafiuddin.syed@ti.com>
fix the following 'make includecheck' warning:
arch/arm/mach-omap2/mcbsp.c: mach/irqs.h is included more than once.
Signed-off-by: Jaswinder Singh Rajput <jaswinderrajput@gmail.com>
Acked-by: Eduardo Valentin <eduardo.valentin@nokia.com>
Acked-by: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Fix two bugs in the OMAP3 clock tree pertaining to the SSI, DSS,
USBHOST, and HSOTGUSB devices. These devices are both interconnect
initiators and targets. Without this patch, clk_enable()s on clocks for
these modules can be very high latency (potentially up to ~200
milliseconds) and message such as the following are generated:
Clock usbhost_48m_fck didn't enable in 100000 tries
Two bugs are fixed by this patch. First, OMAP hardware only supports
target CM_IDLEST register bits on ES2+ chips and beyond. ES1 chips
should not wait for these clocks to enable. So, split the appropriate
clocks into ES1 and ES2+ variants, so that kernels running on ES1
devices won't try to wait.
Second, the current heuristic in omap2_clk_dflt_find_idlest() will
fail for these clocks. It assumes that the CM_IDLEST bit to wait upon
is the same as the CM_*CLKEN bit, which is false[1]. Fix by
implementing custom clkops .find_idlest function pointers for the
appropriate clocks that return the correct slave IDLEST bit shift.
This was originally fixed in the linux-omap kernel during 2.6.29 in a
slightly different manner[2][3].
In the medium-term future, all of the module IDLEST code will
eventually be moved to the omap_hwmod code.
Problem reported by Jarkko Nikula <jhnikula@gmail.com>:
http://marc.info/?l=linux-omap&m=124306184903679&w=2
...
1. See for example 34xx TRM Revision P Table 4-213 and 4-217 (for the
DSS case).
2. http://www.spinics.net/lists/linux-omap/msg05512.html et seq.
3. http://lkml.indiana.edu/hypermail/linux/kernel/0901.3/01498.html
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Jarkko Nikula <jhnikula@gmail.com>
OMAP2430 I2CHS CM_IDLEST bits are in CM_IDLEST1_CORE, but the CM_*CLKEN bits
are in CM_{I,F}CLKEN2_CORE [1]. Fix by implementing a custom clkops
.find_idlest function to return the correct slave IDLEST register.
...
1. OMAP2430 Multimedia Device Package-on-Package (POP) Silicon Revision 2.1
(Rev. V) Technical Reference Manual, tables 4-99 and 4-105.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Some OMAP2/3 hardware modules have CM_IDLEST attributes that are not
handled by the current omap2_wait_clock_ready() code. In preparation
for patches that fix the unusual devices, rename the function
omap2_wait_clock_ready() to omap2_wait_module_ready() and split it
into three parts:
1. A clkops-specific companion clock return function (by default,
omap2_clk_dflt_find_companion())
2. A clkops-specific CM_IDLEST register address and bit shift return
function (by default, omap2_clk_dflt_find_idlest())
3. Code to wait for the CM to indicate that the module is ready
(omap2_cm_wait_idlest())
Clocks can now specify their own custom find_companion() and find_idlest()
functions; used in subsequent patches.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
The clock stabilization delay post a M2 divider change is needed
even before a SDRC interface clock re-enable and not only before
jumping back to SDRAM.
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
This patch fixes a bug in the CORE dpll scaling sequence which was
errouneously clearing some bits in the SDRC DLLA CTRL register and
hence causing a freeze. The issue was observed only on platforms
which scale CORE dpll to < 83Mhz and hence program the DLL in fixed
delay mode.
Issue reported by Limei Wang <E12499@motorola.com>, with debugging
assistance from Richard Woodruff <r-woodruff2@ti.com> and Girish
Ghongdemath <girishsg@ti.com>.
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Cc: Limei Wang <E12499@motorola.com>
Cc: Richard Woodruff <r-woodruff2@ti.com>
Cc: Girish Ghongdemath <girishsg@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
[paul@pwsan.com: updated patch description to include collaboration credits]
Stop setting SDRC_POWER.PWDENA on boot. There is a nasty erratum
(34xx erratum 1.150) that can cause memory corruption if PWDENA is
enabled.
Based originally on a patch from Samu P. Onkalo <samu.p.onkalo@nokia.com>.
Tested on BeagleBoard rev C2.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Samu P. Onkalo <samu.p.onkalo@nokia.com>
This patches ensures the MUX settings are correct for the SDRC
CKE signals to SDRAM. This allows the self-refresh to work when
2 chip-selects are in use.
A warning is thrown away in case the initial muxing is incorrect,
in order to track faulty or old-dated bootloaders.
Note: The CONFIG_OMAP_MUX and CONFIG_OMAP_MUX_WARNINGS options
must be enabled for the mux code to have effect.
Signed-off-by: Jean Pihet <jpihet@mvista.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Some OMAP3 boards (Beagle Cx, Overo, RX51, Pandora) have 2
SDRAM parts connected to the SDRC.
This patch adds the following:
- add a new argument of type omap_sdrc_params struct*
to omap2_init_common_hw and omap2_sdrc_init for the 2nd CS params
- adapted the OMAP boards files to the new prototype of
omap2_init_common_hw
- add the SDRC 2nd CS registers offsets defines
- adapt the sram sleep code to configure the SDRC for the 2nd CS
Note: If the 2nd param to omap2_init_common_hw is NULL, then the
parameters are not programmed into the SDRC CS1 registers
Tested on 3430 SDP and Beagleboard rev C2 and B5, with
suspend/resume and frequency changes (cpufreq).
Signed-off-by: Jean Pihet <jpihet@mvista.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Use async timings when sync timings are not requested.
Also ensure that OneNAND is in async mode when async
timings are used.
Signed-off-by: Adrian Hunter <adrian.hunter@nokia.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The omap_type() function is added and returns the DEVICETYPE field of
the CONTROL_STATUS register. The result can be used for conditional
code based on whether device is GP (general purpose), EMU or
HS (high security). Also move the type defines so omap1 code
compile does not require ifdefs for sections using these defines.
This code is needed for the following fix to set the SRAM
size correctly for HS omaps. Also at least PM and watchdog
code will need this function.
Signed-off-by: Kevin Hilman <khilman@ti.deeprootsystems.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
platform_get_irq may return -ENXIO. but struct omap_mbox mbox_dsp_info.irq
is unsigned, so the error was not noticed.
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Signed-off-by: Hiroshi DOYU <Hiroshi.DOYU@nokia.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
twl_mmc23_set_power() has MMC2 twl_mmc_controller hardcoded in it, which
breaks MMC3. Find the right controller to use instead.
Signed-off-by: Grazvydas Ignotas <notasas@gmail.com>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: Tony Lindgren <tony@atomide.com>
with while (i++ < MAX_CLOCK_ENABLE_WAIT); i can reach MAX_CLOCK_ENABLE_WAIT + 1
after the loop, so if (i == MAX_CLOCK_ENABLE_WAIT) that's still success.
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Correspondence with the TI OMAP hardware team indicates that
SDRC_DLLA_CTRL.FIXEDDELAY should be initialized to 0x0f. This number
was apparently derived from process validation. This is only used
when the SDRC DLL is unlocked (e.g., SDRC clock frequency less than
83MHz).
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Program the SDRC_MR_0 register as well during SDRC clock changes.
This register allows selection of the memory CAS latency. Some SDRAM
chips, such as the Qimonda HYB18M512160AF6, have a lower CAS latency
at lower clock rates.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
When changing the SDRAM clock from 166MHz to 83MHz via the CORE DPLL M2
divider, add a short delay before returning to SDRAM to allow the SDRC
time to stabilize. Without this delay, the system is prone to random
panics upon re-entering SDRAM.
This time delay varies based on MPU frequency. At 500MHz MPU frequency at
room temperature, 64 loops seems to work okay; so add another 32 loops for
environmental and process variation.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
On the OMAP3, initialize SDRC timings when the kernel boots. This ensures
that the kernel is running with known, optimized SDRC timings, rather than
whatever was configured by the bootloader.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
The original CDP kernel that this code comes from waited for 0x800
loops after switching the CORE DPLL M2 divider. This does not appear
to be necessary.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
This patch adds SMP platform specific parts for local(mpu) timer support
for OMAP4430 platform. Each Cortex-a9 core has it's own local timer in the
MPU domain. These timers are not in wakeup domain.
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
This patch adds SMP platform files support for OMAP4430SDP. TI's OMAP4430
SOC is based on ARM Cortex-A9 SMP architecture. It's a dual core SOC
with GIC used for interrupt handling and SCU for cache coherency.
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
This patch updates the Makefile and Kconfig entries for OMAP4. The OMAP4430 SDP
board file supports only minimal set of drivers.
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This patch adds the support for OMAP4. The platform and machine specific
headers and sources updated for OMAP4430 SDP platform.
OMAP4430 is Texas Instrument's SOC based on ARM Cortex-A9 SMP architecture.
It's a dual core SOC with GIC used for interrupt handling and SCU for cache
coherency.
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add support for keypad, GPIO keys and LEDs. Also enable hardware
debounce feature for GPIO keys.
Signed-off-by: Grazvydas Ignotas <notasas@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Setup regulators for MMC1 and MMC2 to get those SD slots
working again.
Signed-off-by: Grazvydas Ignotas <notasas@gmail.com>
CC: David Brownell <david-b@pacbell.net>
Acked-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Initialize regulators for Beagle and Overo.
Patch is based on earlier patches posted to linux-omap mailing
list.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Decouple the HSMMC glue from the twl4030 as the only
regulator provider, using the regulator framework instead.
This makes the glue's "mmc-twl4030" name become a complete
misnomer ... this code could probably all migrate into the
HSMMC driver now.
Tested on 3430SDP (SD and low-voltage MMC) and Beagle (SD),
plus some other boards (including Overo) after they were
converted to set up MMC regulators properly.
Eventually all boards should just associate a regulator with
each MMC controller they use. In some cases (Overo MMC2 and
Pandora MMC3, at least) that would be a fixed-voltage regulator
with no real software control. As a temporary hack (pending
regulator-next updates to make the "fixed.c" regulator become
usable) there's a new ocr_mask field for those boards.
Patch updated with a fix for disabling vcc_aux by
Adrian Hunter <adrian.hunter@nokia.com>
Cc: Pierre Ossman <drzeus-list@drzeus.cx>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Based on an earlier patches by Stanley.Miao <stanley.miao@windriver.com>
and Nishant Kamat <nskamat@ti.com>.
Note that at the ads7846 support still needs support for vaux_control
for the touchscreen to work.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Based on an earlier patch by Stanley.Miao <stanley.miao@windriver.com>
with board-*.c changes split to avoid conflicts with other device updates.
Cc: linux-fbdev-devel@lists.sourceforge.net
Signed-off-by: Stanley.Miao <stanley.miao@windriver.com>
Signed-off-by: Imre Deak <imre.deak@nokia.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add timing data for the Qimonda HYB18M512160AF-6 SDRAM chip, used on
the OMAP3430SDP boards.
Thanks to Rajendra Nayak <rnayak@ti.com> for his help identifying
the chip used on 3430SDP.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add timing data for the Micron MT46H32M32LF-6 SDRAM chip, used on the
OMAP3 Beagle and EVM boards. Original timing data is from the Micron
datasheet PDF downloaded from:
http://download.micron.com/pdf/datasheets/dram/mobile/1gb_ddr_mobile_sdram_t48m.pdf
Thanks to Rajendra Nayak <rnayak@ti.com> for his help identifying
the chips used on Beagle & OMAP3EVM.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Move platform_device_register() for serial device to
omap_serial_init()
There is no need to have arch_initcall() dependency in serial
as already board files call the function omap_serial_init()
Signed-off-by: Vikram Pandita <vikram.pandita@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Based on an earlier patch by Hunyue Yau <hyau@mvista.com> with
board-*.c changes split to avoid conflicts with other device updates.
Cc: linux-fbdev-devel@lists.sourceforge.net
Signed-off-by: Hunyue Yau <hyau@mvista.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: Imre Deak <imre.deak@nokia.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Convert the board-rx51 smc91x code to be generic and make
the boards to use it. This allows future recalculation of the
timings when the source clock gets scaled.
Also correct the rx51 interrupt to be IORESOURCE_IRQ_HIGHLEVEL.
Thanks to Paul Walmsley <paul@pwsan.com> for better GPMC timing
calculations.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add generic onenand support when connected to GPMC and make the
boards to use it.
The patch has been modified to make it more generic to support all
the boards with GPMC. The patch also remove unused prototype for
omap2_onenand_rephase(void).
Note that board-apollon.c is currently using the MTD_ONENAND_GENERIC
and setting the GPMC timings in the bootloader. Setting the GPMC
timings in the bootloader will not allow supporting frequency
scaling for the onenand source clock.
Signed-off-by: Tony Lindgren <tony@atomide.com>
By default, prevent functional wakeups from inside a module from
waking up the IVA2. Let DSP Bridge code handle this when loaded.
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Add D2D clocks (modem_fck, sad2d_ick, mad2d_ick) to clock framework
and ensure that auto-idle bits are set for these clocks during PRCM
init.
Also add omap3_d2d_idle() function called durint PRCM setup which
ensures D2D pins are MUX'd correctly to enable retention for
standalone (no-modem) devices.
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
This patch makes it possible to change uart sleep timeout. New sysfs
entry is added (/sys/devices/platform/serial8250.<uart>/sleep_timeout)
Writing zero will disable the timeout feature and prevent UART clocks
from being disabled.
Also default timeout is increased to 5 second to make serial console
more usable.
Original patch was written by Tero Kristo.
Cc: Tero Kristo <Tero.Kristo@nokia.com>
Signed-off-by: Jouni Hogander <jouni.hogander@nokia.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
This patch allows the UART clocks to be disabled when the OMAP UARTs
are inactive, thus permitting the chip to hit retention in idle.
After the expiration of an activity timer, each UART is allowed to
disable its clocks so the system can enter retention. The activity
timer is (re)activated on any UART interrupt, UART wake event or any
IO pad wakeup. The actual disable of the UART clocks is done in the
'prepare_idle' hook called from the OMAP idle loop.
While the activity timer is active, the smart-idle mode of the UART is
also disabled. This is due to a "feature" of the UART module that
after a UART wakeup, the smart-idle mode may be entered before the
UART has communicated the interrupt, or upon TX, an idle mode may be
entered before the TX FIFOs are emptied.
Upon suspend, the 'prepare_suspend' hook cancels any pending activity
timers and allows the clocks to be disabled immediately.
In addition, upon disabling clocks the UART state is saved in case
of an off-mode transition while clocks are off.
Special thanks to Tero Kristo for the initial ideas and first versions
of UART idle support, and to Jouni Hogander for extra testing and
bugfixes.
Tested on OMAP3 (Beagle, RX51, SDP, EVM) and OMAP2 (n810)
Cc: Tero Kristo <tero.kristo@nokia.com>
Cc: Jouni Hogander <jouni.hogander@nokia.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Add common omap2/3 function to check wether there is irq pending.
Switch to use it in omap2 pm code instead of its own.
Signed-off-by: Jouni Hogander <jouni.hogander@nokia.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
This patch is to sync the core linux-omap PM code with mainline. This
code has evolved and been used for a while the linux-omap tree, but
the attempt here is to finally get this into mainline.
Following this will be a series of patches from the 'PM branch' of the
linux-omap tree to add full PM hardware support from the linux-omap
tree.
Much of this PM core code was written by Jouni Hogander with
significant contributions from Paul Walmsley as well as many others
from Nokia, Texas Instruments and linux-omap community.
Signed-off-by: Jouni Hogander <jouni.hogander@nokia.com>
Cc: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
This reverts commit 5461af5af5.
Adding a disable hook to the irq_chip is not the way to fix the
problem being addressed by this patch. Instead, we need to fix
support for [enable|disable]_irq_wake().
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
We don't necessarily want to compile in irq.o and sdrc.o for omap4.
Also, clock and prcm may not be implemented initially.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Remove OMAP_PRM_REGADDR and use processor specific defines instead.
Also fold in a patch from Kevin Hilman to add _OFFSET #defines
for the PRCM registers to be used with the prm_[read|write]_* macros.
These are used extensively in the forthcoming OMAP PM support.
Also remove now unused OMAP2_PRM_BASE.
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Use processor specific defines instead.
As an extra bonus, this patch fixes the problem of CONFIG_DEBUG_SPINLOCK
calling sched_clock before we have things initialized:
http://patchwork.kernel.org/patch/15810/
Signed-off-by: Tony Lindgren <tony@atomide.com>
We don't necessarily want to compile in irq.o and sdrc.o for omap4.
Also, clock and prcm may not be implemented initially.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Remove OMAP_PRM_REGADDR and use processor specific defines instead.
Also fold in a patch from Kevin Hilman to add _OFFSET #defines
for the PRCM registers to be used with the prm_[read|write]_* macros.
These are used extensively in the forthcoming OMAP PM support.
Also remove now unused OMAP2_PRM_BASE.
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Use processor specific defines instead.
As an extra bonus, this patch fixes the problem of CONFIG_DEBUG_SPINLOCK
calling sched_clock before we have things initialized:
http://patchwork.kernel.org/patch/15810/
Signed-off-by: Tony Lindgren <tony@atomide.com>
Currently "tidspbridge" driver uses its own mmu implementation and
will migrate to use this "omap iommu" eventually. This config is
provided to make this migration happen smoothly.
Signed-off-by: Hiroshi DOYU <Hiroshi.DOYU@nokia.com>
This makes the framebuffer work on omap3.
Also fix the clk_get usage for checkpatch.pl
"ERROR: do not use assignment in if condition".
Cc: Imre Deak <imre.deak@nokia.com>
Cc: linux-fbdev-devel@lists.sourceforge.net
Acked-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The OMAP3430ES2_SAVEANDRESTORE_SHIFT macro is used
by powerdomain code in
"1 << OMAP3430ES2_SAVEANDRESTORE_SHIFT" manner, but
the definition was also (1 << 4), meaning we actually
modified bit 16. So the definition needs to be 4.
This fixes also a cold reset HW bug in OMAP3430 ES3.x
where some of the efuse bits are not isolated during
wake-up from off mode. This can cause randomish
cold resets with off mode. Enabling the USBTLL hardware
SAVEANDRESTORE causes the core power up assert to be
delayed in a way that we will not get faulty values
when boot ROM is reading the unisolated registers.
Signed-off-by: Kalle Jokiniemi <kalle.jokiniemi@digia.com>
Acked-by: Kevin Hilman <khilman@deeprootsystems.com>
Acked-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Rename clk_init_one() to clk_preinit() to distinguish its function
from clk_init() and the individual struct clk init functions.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
On our system we see the following messages:
Disabling unused clock "gpt2_ick"
Disabling unused clock "gpt3_ick"
Disabling unused clock "gpt4_ick"
Disabling unused clock "gpt5_ick"
...
The messages have KERN_INFO level and if you have serial
console, they normally go there. I do not think it is good
idea to print that much stuff there. Moreover, messages
are not properly prefixed and for mortals it is not
immeadietly clear where they come from.
Let's give them debugging level instead.
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
[paul@pwsan.com: trimmed debugging output in patch description]
The CORE DPLL M2 frequency change code should use pr_debug(), not
pr_info(), for its debug messages. Same with
omap2_clksel_round_rate_div(). While here, convert a few printk(KERN_ERR ..
into pr_err().
Signed-off-by: Paul Walmsley <paul@pwsan.com>
According to the 34xx TRM Rev. K section 11.2.4.4.11.1 "Purpose of the
DLL/CDL Module," the SDRC delay-locked-loop can be locked at any SDRC
clock frequency from 83MHz to 166MHz. CDP code unconditionally
unlocked the DLL whenever shifting to a lower SDRC speed, but this
seems unnecessary and error-prone, as the DLL is no longer able to
compensate for process, voltage, and temperature variations. Instead,
only unlock the DLL when the SDRC clock rate would be less than 83MHz.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Renumber registers in omap3_sram_configure_core_dpll() assembly code to
make space for additional parameters.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Sergio Aguirre