The #includes <linux/bug.h> is here to use BUILD_BUG_ON_ZERO().
Thanks to commit bc6245e5ef ("bug: split BUILD_BUG stuff out into
<linux/build_bug.h>"), it is now possible to reduce the number of
headers pulled in.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Save registers lost in the sleep when suspending, and restore them
when resuming.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
For LD11/20 SoCs (capable of per-pin input enable), the iectrl bit
number matches its pin number. So, this is redundant information.
Instead, we just need a flag to know if the iectrl gating exists or not.
With this refactoring, 5 bits in pin data will be saved.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
There are a bunch of GPIO muxing data, but most of them are actually
unneeded because GPIO-to-pin mapping can be specified by "gpio-ranges"
DT properties.
Tables that contain a set of GPIO pins are still needed for the named
mapping by "gpio-ranges-group-names". This is a much cleaner way for
UniPhier SoC family where GPIO numbers are not straight mapped to pin
numbers.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Since commit 3e030b0b4e ("pinctrl: uniphier: allow to have pinctrl
node under syscon node"), this driver has kept compatibility for the
old DT files. Several releases have passed since then, so remove
the obsoleted compatibles and clean up the code.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
PH1-LD4 and PH1-sLD8 SoCs have pins that support pin configuration
(pin biasing, drive strength control), but not pin-muxing.
Allow to fill the mux value table with -1 for those pins; pins with
mux value -1 will be skipped in the pin-mux set function. The mux
value type should be changed from "unsigned" to "int" in order to
accommodate -1 as a special case.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Upcoming new pinctrl drivers for PH1-LD11 and PH-LD20 support input
signal gating for each pin. (While, existing ones only support it
per pin-group.) This commit updates the core part for that.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The core part of the UniPhier pinctrl driver needs to support a new
capability for upcoming UniPhier ARMv8 SoCs. This sometimes happens
because pinctrl drivers include really SoC-specific stuff.
This commit intends to tidy up SoC-specific parameters of the existing
drivers before adding the new one. Having just one flag would be
better than adding a new struct member every time a new SoC-specific
capability comes up.
At this time, there is one flag, UNIPHIER_PINCTRL_CAPS_DBGMUX_SEPARATE.
This capability (I'd say rather quirk) was added for PH1-Pro4 and
PH1-Pro5 as requirement from a customer. For those SoCs, one pin-mux
setting is controlled by the combination of two separate registers; the
LSB bits at register offset (8 * N) and the MSB bits at (8 * N + 4).
Because it is impossible to update two separate registers atomically,
the LOAD_PINCTRL register should be set in order to make the pin-mux
settings really effective.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The new ARMv8 SoC, PH1-LD20, supports more fine-grained drive
strength control. Drive strength of some pins are controlled by
3-bit width registers (8-level granularity).
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The new ARMv8 SoC, PH1-LD20, supports more fine-grained drive
strength control. Some of the configuration registers on it have
3-bit width.
The feature will be supported in the next commit, but a problem is
that macro names are getting longer and longer in the current naming
scheme.
Before moving forward, this commit renames macros as follows:
UNIPHIER_PIN_DRV_4_8 -> UNIPHIER_PIN_DRV_1BIT
UNIPHIER_PIN_DRV_8_12_16_20 -> UNIPHIER_PIN_DRV_2BIT
UNIPHIER_PIN_DRV_FIXED_4 -> UNIPHIER_PIN_DRV_FIXED4
UNIPHIER_PIN_DRV_FIXED_5 -> UNIPHIER_PIN_DRV_FIXED5
UNIPHIER_PIN_DRV_FIXED_8 -> UNIPHIER_PIN_DRV_FIXED8
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Currently, every SoC driver defines struct pinctrl_desc statically,
i.e. it consumes memory footprint even if it is not probed.
In multi-platform, many pinctrl drivers are linked (generally as
built-in objects), although only one of them is actually used.
So, it is reasonable to allocate memory dynamically where possible.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Use devm_pinctrl_register() for pin control registration and remove
need of .remove callback.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The core support for the pinctrl drivers for all the UniPhier SoCs.
Changes in v2:
- drop vogus THIS_MODULE because this file is always built-in
- drop vogus "include <linux/module.h> because this file is
always built-in
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Masahiro Yamada