Add the DMA engine driver for the QCOM Bus Access Manager (BAM) DMA controller
found in the MSM 8x74 platforms.
Each BAM DMA device is associated with a specific on-chip peripheral. Each
channel provides a uni-directional data transfer engine that is capable of
transferring data between the peripheral and system memory (System mode), or
between two peripherals (BAM2BAM).
The initial release of this driver only supports slave transfers between
peripherals and system memory.
Signed-off-by: Andy Gross <agross@codeaurora.org>
Tested-by: Stanimir Varbanov <svarbanov@mm-sol.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
We can move the handling of the DMA synchronisation control out of the
prepare functions; this can be pre-calculated when the DMA channel has
been allocated, so we don't need to duplicate this in both prepare
functions.
Acked-by: Tony Lindgren <tony@atomide.com>
Acked-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Move the interrupt handling for OMAP2+ into omap-dma, rather than using
the legacy support in the platform code.
Acked-by: Tony Lindgren <tony@atomide.com>
Acked-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Export the DMA register information from the SoC specific data, such
that we can access the registers directly in omap-dma.c, mapping the
register region ourselves as well.
Rather than calculating the DMA channel register in its entirety for
each access, we pre-calculate an offset base address for the allocated
DMA channel and then just use the appropriate register offset.
Acked-by: Tony Lindgren <tony@atomide.com>
Acked-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Provide a function to read the CSAC/CDAC register, working around the
OMAP 3.2/3.3 erratum (which requires two reads of the register if the
first returned zero.
Acked-by: Tony Lindgren <tony@atomide.com>
Acked-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Provide a pair of channel register accessors, and a pair of global
accessors for non-channel specific registers.
Acked-by: Tony Lindgren <tony@atomide.com>
Acked-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
We don't need to read-modify-write the CCR register; we already know
what value it should contain at this point. Use the cached CCR value
when setting the enable bit.
Acked-by: Tony Lindgren <tony@atomide.com>
Acked-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
We don't need to issue a barrier for every segment of a DMA transfer;
doing this just once per descriptor will do.
Acked-by: Tony Lindgren <tony@atomide.com>
Acked-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Move the clnk_ctrl setup to the preparation functions, saving its
value in the omap_desc. This only needs to be set once per descriptor,
not for each segment, so set it in omap_dma_start_desc() rather than
omap_dma_start().
Acked-by: Tony Lindgren <tony@atomide.com>
Acked-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The only thing which changes is which registers are written, so put this
in local variables instead. This results in smaller code.
Acked-by: Tony Lindgren <tony@atomide.com>
Acked-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Consolidate clearing of the channel status register, rather than open
coding the same functionality in two places.
Acked-by: Tony Lindgren <tony@atomide.com>
Acked-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Since we record the CCR register in the dma transaction, we can move the
processing of the iframe buffering errata out of the omap_dma_start().
Move it to the preparation functions.
Acked-by: Tony Lindgren <tony@atomide.com>
Acked-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Provide our own set of more complete register definitions; this allows
us to get rid of the meaningless 1 << n constants scattered throughout
this code.
Acked-by: Tony Lindgren <tony@atomide.com>
Acked-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Consolidate the setup of the channel control register. Prepare the
basic value in the preparation of the DMA descriptor, and write it into
the register upon descriptor execution.
Acked-by: Tony Lindgren <tony@atomide.com>
Acked-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Consolidate the setup of the channel source destination parameters
register. This way, we calculate the required CSDP value when we setup
a transfer descriptor, and only write it to the device registers once
when we start the descriptor.
Acked-by: Tony Lindgren <tony@atomide.com>
Acked-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Read the current DMA position from the hardware directly rather than via
arch/arm/plat-omap/dma.c.
Acked-by: Tony Lindgren <tony@atomide.com>
Acked-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Program the non-cyclic mode DMA start/stop directly, rather than via
arch/arm/plat-omap/dma.c.
Acked-by: Tony Lindgren <tony@atomide.com>
Acked-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
There's no need to keep writing registers which don't change value in
omap_dma_start_sg(). Move this into omap_dma_start_desc() and merge
the register updates together.
Acked-by: Tony Lindgren <tony@atomide.com>
Acked-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Program the transfer parameters directly into the hardware, rather
than using the functions in arch/arm/plat-omap/dma.c.
Acked-by: Tony Lindgren <tony@atomide.com>
Acked-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Provide and use a hook to obtain the underlying DMA platform operations
so that omap-dma.c can access the hardware more directly without
involving the legacy DMA driver.
Acked-by: Tony Lindgren <tony@atomide.com>
Acked-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Use devm_kzalloc() to allocate omap_dmadev() so that we don't need
complex error cleanup paths.
Acked-by: Tony Lindgren <tony@atomide.com>
Acked-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
move to support of_dma_request_slave_channel() and dma_request_slave_channel.
we add a xlate() to let dma clients be able to find right dma_chan by generic
"dmas" properties in dts.
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Barry Song <Baohua.Song@csr.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
With the callback implemented omap-dma can provide information to client
drivers regarding to supported address widths, directions, residue
granularity, etc.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
This is to disable/enable DW_DMAC hw during late suspend/early resume.
Since DMA is providing service to other clients (eg: SPI, HSUART),
we need to ensure DMA suspends after the clients and resume
before the clients are active.
Signed-off-by: Chew, Chiau Ee <chiau.ee.chew@intel.com>
Acked-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
This makes the probe() function a little bit clearer.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Prevents test result strings from being output on same line. Issue will
happen with verbose and multi-iteration modes enabled.
Signed-off-by: Jerome Blin <jerome.blin@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
As discussed in [1] the tasklet_disable is not a proper function for teardown.
We need to ensure irq is disabled, followed by ensuring that don't schedule any
more tasklets and then its safe to use tasklet_kill().
Here in pch dma driver we need to use free_irq() before tasklet_kill(). So move
up the free_irq() which will ensure that the irq is disabled and also wait till
all scheduled interrupts are executed by invoking synchronize_irq().
[1]: http://lwn.net/Articles/588457/
Reported-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
As discussed in [1] the tasklet_disable is not a proper function for teardown.
We need to ensure irq is disabled, followed by ensuring that don't schedule any
more tasklets and then its safe to use tasklet_kill().
Here in at_hdmac driver we use free_irq() before tasklet_kill(). The free_irq()
will ensure that the irq is disabled and also wait till all scheduled interrupts
are executed by invoking synchronize_irq(). So we need to only do tasklet_kill()
after invoking free_irq()
[1]: http://lwn.net/Articles/588457/
Reported-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Start the channel tear down only if the channel is busy, else just
bail out. In some cases its seen that by the time the tear down is
initiated the cppi completes the DMA, especially in ISOCH transfers.
Signed-off-by: George Cherian <george.cherian@ti.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
There is a bug in s3c24xx_dma_probe() where we do:
phy->irq = platform_get_irq(pdev, i);
if (phy->irq < 0) {
The problem is that "phy->irq" is unsigned so the error handling doesn't
work. I have changed it to signed.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Use the dev_* message logging API instead of raw printk.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
The static checker reports following warning:
drivers/dma/fsl-edma.c:732 fsl_edma_xlate()
error: we previously assumed 'chan' could be null (see line 737)
The changes of the loop cursor in the iteration may result in
NULL dereference when dma_get_slave_channel failed but loop
will continue. So use list_for_each_entry_safe() instead of
list_for_each_entry() to against this.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Jingchang Lu <b35083@freescale.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
This patch makes the mmp_tdma controller able to provide DMA
resources in DT environments by providing an dma xlate function to
get the generic DMA device tree helper support. Then DMA clients only
need to call dma_request_slave_channel() for requesting a DMA channel
from dmaengine.
Signed-off-by: Nenghua Cao <nhcao@marvell.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
For some SOCes use mmp_pdma, they have several dma controllers
sharing same irq.
So add IRQF_SHARED to flag when request irq. It can make multiple
controllers share the same irq.
Signed-off-by: Chao Xie <chao.xie@marvell.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Fix a memory leak in the edma_prep_dma_cyclic() error handling path.
Signed-off-by: Christian Engelmayer <cengelma@gmx.at>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
The structure isn't used outside of its compilation unit. Make it
static.
Cc: Guennadi Liakhovetski <g.liakhovetski+renesas@gmail.com>
Cc: Vinod Koul <vinod.koul@intel.com>
Cc: dmaengine@vger.kernel.org
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Several functions and variables are use on SH_CPU4 or ARM only. Guard
their declaration with conditional compilation directives to avoid
warnings.
Cc: Guennadi Liakhovetski <g.liakhovetski+renesas@gmail.com>
Cc: Vinod Koul <vinod.koul@intel.com>
Cc: dmaengine@vger.kernel.org
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Use the %zu and %pad printk specifiers to print size_t and dma_addr_t
variables, and cast pointers to uintptr_t instead of unsigned int where
applicable. This fixes warnings on platforms where pointers and/or
dma_addr_t have a different size than int
Cc: Guennadi Liakhovetski <g.liakhovetski+renesas@gmail.com>
Cc: Vinod Koul <vinod.koul@intel.com>
Cc: dmaengine@vger.kernel.org
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Pull slave-dma fixes from Vinod Koul:
"This request brings you two small fixes. First one for fixing
dereference of freed descriptor and second for fixing sdma bindings
for it to work for imx25.
I was planning to send this about 10days ago but then I had to proceed
on my paternity leave and didnt get chance to send this. Now got a
bit of time from dady duties :)"
* 'fixes' of git://git.infradead.org/users/vkoul/slave-dma:
dma: sdma: Add imx25 compatible
dma: ste_dma40: don't dereference free:d descriptor
Since commit 7787380336 "net_dma: mark broken" we no longer pin dma
engines active for the network-receive-offload use case. As a result
the ->free_chan_resources() that occurs after the driver self test no
longer has a NET_DMA induced ->alloc_chan_resources() to back it up. A
late firing irq can lead to ksoftirqd spinning indefinitely due to the
tasklet_disable() performed by ->free_chan_resources(). Only
->alloc_chan_resources() can clear this condition in affected kernels.
This problem has been present since commit 3e037454bc "I/OAT: Add
support for MSI and MSI-X" in 2.6.24, but is now exposed. Given the
NET_DMA use case is deprecated we can revisit moving the driver to use
threaded irqs. For now, just tear down the irq and tasklet properly by:
1/ Disable the irq from triggering the tasklet
2/ Disable the irq from re-arming
3/ Flush inflight interrupts
4/ Flush the timer
5/ Flush inflight tasklets
References:
https://lkml.org/lkml/2014/1/27/282https://lkml.org/lkml/2014/2/19/672
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: <stable@vger.kernel.org>
Reported-by: Mike Galbraith <bitbucket@online.de>
Reported-by: Stanislav Fomichev <stfomichev@yandex-team.ru>
Tested-by: Mike Galbraith <bitbucket@online.de>
Tested-by: Stanislav Fomichev <stfomichev@yandex-team.ru>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
imx25 did not work without a firmware previously.
This patch adds a DT compatible to pass the correct data with the
default script addresses for imx25.
Add imx25 compatible to the list of compatibles in the binding
documentation.
Signed-off-by: Markus Pargmann <mpa@pengutronix.de>
Acked-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Add Freescale enhanced direct memory(eDMA) controller support.
This module can be found on Vybrid and LS-1 SoCs.
Signed-off-by: Alison Wang <b18965@freescale.com>
Signed-off-by: Jingchang Lu <b35083@freescale.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
There is couple of leftovers in the comment blocks. This patch modifies the
comments accordingly.
There is no functional change.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
It appears that in the DMA40 driver the DMA tasklet will very
often dereference memory for a descriptor just free:d from the
DMA40 slab. Nothing happens because no other part of the driver
has yet had a chance to claim this memory, but it's really
nasty to dereference free:d memory, so let's check the flag
before the descriptor is free and store it in a bool variable.
Cc: stable@vger.kernel.org
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Enabling some of the mvebu platforms in the multiplatform config for ARM
enabled these drivers, which also triggered a bunch of warnings when LPAE
is enabled (thus making phys_addr_t 64-bit).
Most changes are switching printk formats, but also a bit of changes to what
used to be array-based pointer arithmetic that could just be done with the
address types instead.
The warnings were:
drivers/dma/mv_xor.c: In function 'mv_xor_tx_submit':
drivers/dma/mv_xor.c:500:3: warning: format '%x' expects argument of type
'unsigned int', but argument 4 has type 'dma_addr_t' [-Wformat]
drivers/dma/mv_xor.c: In function 'mv_xor_alloc_chan_resources':
drivers/dma/mv_xor.c:553:13: warning: cast to pointer from integer of
different size [-Wint-to-pointer-cast]
drivers/dma/mv_xor.c:555:4: warning: cast from pointer to integer of
different size [-Wpointer-to-int-cast]
drivers/dma/mv_xor.c: In function 'mv_xor_prep_dma_memcpy':
drivers/dma/mv_xor.c:584:2: warning: format '%x' expects argument of type
'unsigned int', but argument 5 has type 'dma_addr_t' [-Wformat]
drivers/dma/mv_xor.c:584:2: warning: format '%x' expects argument of type
'unsigned int', but argument 6 has type 'dma_addr_t' [-Wformat]
drivers/dma/mv_xor.c: In function 'mv_xor_prep_dma_xor':
drivers/dma/mv_xor.c:628:2: warning: format '%u' expects argument of type
'unsigned int', but argument 7 has type 'dma_addr_t' [-Wformat]
Acked-by: Vinod Koul <vinod.koul@intel.com>
Acked-by: Jason Cooper <jason@lakedaemon.net>
Signed-off-by: Olof Johansson <olof@lixom.net>
In case of PCI mode the DMA controller has a specific ID. Put this ID to the
list of supported.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Currently acpi_dma_request_slave_chan_by_index() and
acpi_dma_request_slave_chan_by_name() return only requested channel or NULL.
This patch converts them to return appropriate error code instead of NULL in
case of unsuccessfull request.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Since devm_destroy() doesn't call release function we have to use
devm_release() instead.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Commit 96286b5766 ("dmaengine: Add support for BCM2835") added an
optional dependency on MACH_BCM2708. But there's no Kconfig symbol
MACH_BCM2708.
(There was an entry for MACH_BCM2708 in arch/arm/tools/mach-types from
v2.6.37 until v3.2. But it seems that entry was never used in the tree.)
This optional dependency can safely be removed.
Signed-off-by: Paul Bolle <pebolle@tiscali.nl>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Move the DMA_OF selection to the DMA driver to fix kconfig warning:
warning: (ARCH_MOXART) selects DMA_OF which has unmet direct dependencies (DMADEVICES && OF)
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Olof Johansson <olof@lixom.net>
Pull slave-dma updates from Vinod Koul:
- new driver for BCM2835 used in R-pi
- new driver for MOXA ART
- dma_get_any_slave_channel API for DT based systems
- minor fixes and updates spread acrooss driver
[ The fsl-ssi dual fifo mode support addition clashed badly with the
other changes to fsl-ssi that came in through the sound merge. I did
a very rough cut at fixing up the conflict, but Nicolin Chen (author
of both sides) will need to verify and check things ]
* 'for-linus' of git://git.infradead.org/users/vkoul/slave-dma: (36 commits)
dmaengine: mmp_pdma: fix mismerge
dma: pl08x: Export pl08x_filter_id
acpi-dma: align documentation with kernel-doc format
dma: fix vchan_cookie_complete() debug print
DMA: dmatest: extend the "device" module parameter to 32 characters
drivers/dma: fix error return code
dma: omap: Set debug level to debugging messages
dmaengine: fix kernel-doc style typos for few comments
dma: tegra: add support for Tegra148/124
dma: dw: use %pad instead of casting dma_addr_t
dma: dw: join split up messages
dma: dw: fix style of multiline comment
dmaengine: k3dma: fix sparse warnings
dma: pl330: Use dma_get_slave_channel() in the of xlate callback
dma: pl330: Differentiate between submitted and issued descriptors
dmaengine: sirf: Add device_slave_caps interface
DMA: Freescale: change BWC from 256 bytes to 1024 bytes
dmaengine: Add MOXA ART DMA engine driver
dmaengine: Add DMA_PRIVATE to BCM2835 driver
dma: imx-sdma: Assign a default script number for ROM firmware cases
...
The merge between 2b7f65b11d "mmp_pdma: Style neatening" and
8010dad55a "dma: add dma_get_any_slave_channel(), for use in of_xlate()"
caused a build error by leaving obsolete code in place:
mmp_pdma.c: In function 'mmp_pdma_dma_xlate':
mmp_pdma.c:909:31: error: 'candidate' undeclared
mmp_pdma.c:912:3: error: label 'retry' used but not defined
mmp_pdma.c:901:24: warning: unused variable 'c' [-Wunused-variable]
This removes the extraneous lines.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Export the symbol so that it is accessible to modules.
Fixes the following error:
ERROR: "pl08x_filter_id" [sound/soc/samsung/snd-soc-s3c-dma.ko] undefined!
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Cc: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
It mostly fixes the "RETURN" sections in the resulting manual page.
There is no functional change.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
vd->tx.cookie is set zero on dma_cookie_complete(),
save to local before printing it.
Signed-off-by: Jonas Jensen <jonas.jensen@gmail.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
DT and DT-conversion-related changes for various ARM platforms. Most
of these are to enable various devices on various boards, etc, and not
necessarily worth enumerating.
New boards and systems continue to come in as new devicetree files that
don't require corresponding C changes any more, which is indicating that
the system is starting to work fairly well.
A few things worth pointing out:
* ST Ericsson ux500 platforms have made the major push to move over to fully
support the platform with DT.
* Renesas platforms continue their conversion over from legacy platform devices
to DT-based for hardware description.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=4o2d
-----END PGP SIGNATURE-----
Merge tag 'dt-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC DT updates from Olof Johansson:
"DT and DT-conversion-related changes for various ARM platforms. Most
of these are to enable various devices on various boards, etc, and not
necessarily worth enumerating.
New boards and systems continue to come in as new devicetree files
that don't require corresponding C changes any more, which is
indicating that the system is starting to work fairly well.
A few things worth pointing out:
* ST Ericsson ux500 platforms have made the major push to move over
to fully support the platform with DT
* Renesas platforms continue their conversion over from legacy
platform devices to DT-based for hardware description"
* tag 'dt-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (327 commits)
ARM: dts: SiRF: add pin group for USP0 with only RX or TX frame sync
ARM: dts: SiRF: add lost usp1_uart_nostreamctrl pin group for atlas6
ARM: dts: sirf: add lost minigpsrtc device node
ARM: dts: sirf: add clock, frequence-voltage table for CPU0
ARM: dts: sirf: add lost bus_width, clock and status for sdhci
ARM: dts: sirf: add lost clocks for cphifbg
ARM: dts: socfpga: add pl330 clock
ARM: dts: socfpga: update L2 tag and data latency
arm: sun7i: cubietruck: Enable the i2c controllers
ARM: dts: add support for EXYNOS4412 based TINY4412 board
ARM: dts: Add initial support for Arndale Octa board
ARM: bcm2835: add USB controller to device tree
ARM: dts: MSM8974: Add MMIO architected timer node
ARM: dts: MSM8974: Add restart node
ARM: dts: sun7i: external clock outputs
ARM: dts: sun7i: Change 32768 Hz oscillator node name to clk@N style
ARM: dts: sun7i: Add pin muxing options for clock outputs
ARM: dts: sun7i: Add rtp controller node
ARM: dts: sun5i: Add rtp controller node
ARM: dts: sun4i: Add rtp controller node
...
This is the branch where we usually queue up cleanup efforts, moving
drivers out of the architecture directory, header file restructuring,
etc. Sometimes they tangle with new development so it's hard to keep it
strictly to cleanups.
Some of the things included in this branch are:
* Atmel SAMA5 conversion to common clock
* Reset framework conversion for tegra platforms
- Some of this depends on tegra clock driver reworks that are shared with Mike
Turquette's clk tree.
* Tegra DMA refactoring, which are shared branches with the DMA tree.
* Removal of some header files on exynos to prepare for multiplatform
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=3CcT
-----END PGP SIGNATURE-----
Merge tag 'cleanup-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC cleanups from Olof Johansson:
"This is the branch where we usually queue up cleanup efforts, moving
drivers out of the architecture directory, header file restructuring,
etc. Sometimes they tangle with new development so it's hard to keep
it strictly to cleanups.
Some of the things included in this branch are:
* Atmel SAMA5 conversion to common clock
* Reset framework conversion for tegra platforms
- Some of this depends on tegra clock driver reworks that are shared
with Mike Turquette's clk tree.
* Tegra DMA refactoring, which are shared branches with the DMA tree.
* Removal of some header files on exynos to prepare for
multiplatform"
* tag 'cleanup-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (169 commits)
ARM: mvebu: move Armada 370/XP specific definitions to armada-370-xp.h
ARM: mvebu: remove prototypes of non-existing functions from common.h
ARM: mvebu: move ARMADA_XP_MAX_CPUS to armada-370-xp.h
serial: sh-sci: Rework baud rate calculation
serial: sh-sci: Compute overrun_bit without using baud rate algo
serial: sh-sci: Remove unused GPIO request code
serial: sh-sci: Move overrun_bit and error_mask fields out of pdata
serial: sh-sci: Support resources passed through platform resources
serial: sh-sci: Don't check IRQ in verify port operation
serial: sh-sci: Set the UPF_FIXED_PORT flag
serial: sh-sci: Remove duplicate interrupt check in verify port op
serial: sh-sci: Simplify baud rate calculation algorithms
serial: sh-sci: Remove baud rate calculation algorithm 5
serial: sh-sci: Sort headers alphabetically
ARM: EXYNOS: Kill exynos_pm_late_initcall()
ARM: EXYNOS: Consolidate selection of PM_GENERIC_DOMAINS for Exynos4
ARM: at91: switch Calao QIL-A9260 board to DT
clk: at91: fix pmc_clk_ids data type attriubte
PM / devfreq: use inclusion <mach/map.h> instead of <plat/map-s5p.h>
ARM: EXYNOS: remove <mach/regs-clock.h> for exynos
...
With Device Tree a typical DMA controller device name can look like
10000000.dma-controller, which extends the current size of the string,
allocated for this parameter. This patch extends its size from 20 to 32
characters.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Set the return variable to an error code as done elsewhere in the function.
A simplified version of the semantic match that finds this problem is as
follows: (http://coccinelle.lip6.fr/)
// <smpl>
(
if@p1 (\(ret < 0\|ret != 0\))
{ ... return ret; }
|
ret@p1 = 0
)
... when != ret = e1
when != &ret
*if(...)
{
... when != ret = e2
when forall
return ret;
}
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
The channel allocated/released messages are just informative and
not really interesting to users. Change them to "debug" level.
Signed-off-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Tegra148 introduces a few changes to the APB DMA HW registers. Update the
driver to cope with them. Tegra124 inherits these changes.
* The register address stride between DMA channels increases.
* A new per-channel WCOUNT register is introduced.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Kunal Agrawal <kunala@nvidia.com>
[swarren, remove .dts file change, rewrote commit description, removed
some duplicate/unused code and register IO]
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Reviewed-by: Thierry Reding <treding@nvidia.com>
Tested-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Since we have nice helper to print dma_addr_t values by reference we may use it
instead of explicit casting to a longest type.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
The joined messages are better to grep when debugging.
There is no functional change.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Simple fix a style of the multiline comment.
There is no functional change.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Fix sparse warnings:
drivers/dma/k3dma.c:480:20: warning: Using plain integer as NULL pointer
drivers/dma/k3dma.c:820:1: warning: symbol 'k3_dma_pmops' was not declared. Should it be static?
Signed-off-by: Zhangfei Gao <zhangfei.gao@linaro.org>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Currently the driver uses dma_request_channel() with a custom filter function to
find the requested channel. This will loop over all available channels until the
one we want has been found, but we already know which channel we want to
request, so we can dma_get_slave_channel(). This also makes the code a bit
shorter cleaner.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
The pl330 dmaengine driver currently does not differentiate between submitted
and issued descriptors. It won't start transferring a newly submitted
descriptor until issue_pending() is called, but only if it is idle. If it is
active and a new descriptor is submitted before it goes idle it will happily
start the newly submitted descriptor once all earlier submitted descriptors have
been completed. This is not a 100% correct with regards to the dmaengine
interface semantics. A descriptor is not supposed to be started until the next
issue_pending() call after the descriptor has been submitted. This patch adds a
second per channel list that keeps track of the submitted descriptors. Once
issue_pending() is called the submitted descriptors are moved to the working
list and only descriptors on the working list are started.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
this patch adds device_slave_caps() callback as SiRF SoC sound drivers
depend on it.
Signed-off-by: Rongjun Ying <rongjun.ying@csr.com>
Signed-off-by: Barry Song <Barry.Song@csr.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Freescale DMA has a feature of BandWidth Control (ab. BWC), which is currently
256 bytes and should be changed to 1024 bytes for best DMA throughput.
Changing BWC from 256 to 1024 will improve DMA performance much, in cases
whatever one channel is running or multi channels are running simultanously,
large or small buffers are copied. And this change doesn't impact memory
access performance remarkably, lmbench tests show that for some cases the
memory performance are decreased very slightly, while the others are even
better.
Tested on T4240.
Signed-off-by: Hongbo Zhang <hongbo.zhang@freescale.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
The MOXA ART SoC has a DMA controller capable of offloading expensive
memory operations, such as large copies. This patch adds support for
the controller including four channels. Two of these are used to
handle MMC copy on the UC-7112-LX hardware. The remaining two can be
used in a future audio driver or client application.
Signed-off-by: Jonas Jensen <jonas.jensen@gmail.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Without DMA_PRIVATE the driver is not able to allocate more than one channel.
Since it uses dma_get_any_slave_channel that calls private_candidate,
the second allocation fails at
/* some channels are already publicly allocated */
Maybe it should be fixed in the core, but at least this fixes the bug.
Signed-off-by: Florian Meier <florian.meier@koalo.de>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
The pl330 driver currently does not support residue reporting, so set the
residue granularity to DMA_RESIDUE_GRANULARITY_DESCRIPTOR.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
i.MX series have inner firmware in its ROM code: when SDMA isn't provided
any firmware from Kernel or rootfs, the default inner ROM firmware will be
activated. However the current driver doesn't assign any script number to
this situation, and those platform running in this case would be broken.
Thus this patch adds a default script number when no external firmware being
loaded so that people would continue to be able to use basic scripts to run
their platform without any firmware.
Reported-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Nicolin Chen <Guangyu.Chen@freescale.com>
Tested-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Support to get sram pool from generic device tree binding. The
existing way of get sram poll, directly call sram_get_gpool(), still
work here.
Signed-off-by: Nenghua Cao <nhcao@marvell.com>
Acked-by: Zhangfei Gao <zhangfei.gao@gmail.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Add support for DMA controller of BCM2835 as used in the Raspberry Pi.
Currently it only supports cyclic DMA.
Signed-off-by: Florian Meier <florian.meier@koalo.de>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Bringing in the tegra dma/reset framework cleanup as a base for the DT changes.
* tegra/dma-reset-rework: (320 commits)
spi: tegra: checking for ERR_PTR instead of NULL
ASoC: tegra: update module reset list for Tegra124
clk: tegra: remove bogus PCIE_XCLK
clk: tegra: remove legacy reset APIs
ARM: tegra: remove legacy DMA entries from DT
ARM: tegra: remove legacy clock entries from DT
USB: EHCI: tegra: use reset framework
Input: tegra-kbc - use reset framework
serial: tegra: convert to standard DMA DT bindings
serial: tegra: use reset framework
spi: tegra: convert to standard DMA DT bindings
spi: tegra: use reset framework
staging: nvec: use reset framework
i2c: tegra: use reset framework
ASoC: tegra: convert to standard DMA DT bindings
ASoC: tegra: allocate AHUB FIFO during probe() not startup()
ASoC: tegra: call pm_runtime APIs around register accesses
ASoC: tegra: use reset framework
dma: tegra: register as an OF DMA controller
dma: tegra: use reset framework
...
Signed-off-by: Olof Johansson <olof@lixom.net>
This series converts the Tegra DTs and drivers to use the common/
standard DMA and reset bindings, rather than custom bindings. It also
adds complete documentation for the Tegra clock bindings without
actually changing any binding definitions.
This conversion relies on a few sets of patches in branches from outside
the Tegra tree:
1) A patch to add an DMA channel request API which allows deferred probe
to be implemented.
2) A patch to implement a common part of the of_xlate function for DMA
controllers.
3) Some ASoC patches (which in turn rely on (1) above), which support
deferred probe during DMA channel allocation.
4) The Tegra clock driver changes for 3.14.
Consequently, this branch is based on a merge of all of those external
branches.
In turn, this branch is or will be pulled into a few places that either
rely on features introduced here, or would otherwise conflict with the
patches:
a) Tegra's own for-3.14/powergate and for-4.14/dt branches, to avoid
conflicts.
b) The DRM tree, which introduces new code that relies on the reset
controller framework introduced in this branch, and to avoid
conflicts.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=8T7+
-----END PGP SIGNATURE-----
Merge tag 'tegra-for-3.14-dmas-resets-rework' of git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux into next/cleanup
From Stephen Warren:
ARM: tegra: implement common DMA and resets DT bindings
This series converts the Tegra DTs and drivers to use the common/
standard DMA and reset bindings, rather than custom bindings. It also
adds complete documentation for the Tegra clock bindings without
actually changing any binding definitions.
This conversion relies on a few sets of patches in branches from outside
the Tegra tree:
1) A patch to add an DMA channel request API which allows deferred probe
to be implemented.
2) A patch to implement a common part of the of_xlate function for DMA
controllers.
3) Some ASoC patches (which in turn rely on (1) above), which support
deferred probe during DMA channel allocation.
4) The Tegra clock driver changes for 3.14.
Consequently, this branch is based on a merge of all of those external
branches.
In turn, this branch is or will be pulled into a few places that either
rely on features introduced here, or would otherwise conflict with the
patches:
a) Tegra's own for-3.14/powergate and for-4.14/dt branches, to avoid
conflicts.
b) The DRM tree, which introduces new code that relies on the reset
controller framework introduced in this branch, and to avoid
conflicts.
* tag 'tegra-for-3.14-dmas-resets-rework' of git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux: (30 commits)
spi: tegra: checking for ERR_PTR instead of NULL
ASoC: tegra: update module reset list for Tegra124
clk: tegra: remove bogus PCIE_XCLK
clk: tegra: remove legacy reset APIs
ARM: tegra: remove legacy DMA entries from DT
ARM: tegra: remove legacy clock entries from DT
USB: EHCI: tegra: use reset framework
Input: tegra-kbc - use reset framework
serial: tegra: convert to standard DMA DT bindings
serial: tegra: use reset framework
spi: tegra: convert to standard DMA DT bindings
spi: tegra: use reset framework
staging: nvec: use reset framework
i2c: tegra: use reset framework
ASoC: tegra: convert to standard DMA DT bindings
ASoC: tegra: allocate AHUB FIFO during probe() not startup()
ASoC: tegra: call pm_runtime APIs around register accesses
ASoC: tegra: use reset framework
dma: tegra: register as an OF DMA controller
dma: tegra: use reset framework
...
Signed-off-by: Olof Johansson <olof@lixom.net>
Merging in external dependencies for the Tegra DMA and reset controller
refactoring from external trees.
Per Stephen Warren, the stability of these branches have been negotiated
with the relevant parties (Vinod/Mark/Mike)
* depends/asoc-dma:
ASoC: dmaengine: fix deferred probe detection
ASoC: dmaengine: support deferred probe for DMA channels
dma: add channel request API that supports deferred probe
ASoC: dmaengine: add custom DMA config to snd_dmaengine_pcm_config
ASoC: don't leak on error in snd_dmaengine_pcm_register
ASoC: restructure dmaengine_pcm_request_chan_of()
ASoC: generic-dmaengine-pcm: Set BATCH flag when residue reporting is not supported
ASoC: Add resource managed snd_dmaengine_pcm_register()
* depends/dma-of:
dma: add dma_get_any_slave_channel(), for use in of_xlate()
* depends/tegra-clk: (42 commits)
clk: tegra: fix __clk_lookup() return value checks
clk: tegra: Do not print errors for clk_round_rate()
clk: tegra: Initialize DSI low-power clocks
clk: tegra: add FUSE clock device
clk: tegra: Properly setup PWM clock on Tegra30
clk: tegra: Initialize secondary gr3d clock on Tegra30
clk: tegra114: Initialize clocks needed for HDMI
clk: tegra124: add suspend/resume function for tegra_cpu_car_ops
clk: tegra124: add wait_for_reset and disable_clock for tegra_cpu_car_ops
clk: tegra124: Add support for Tegra124 clocks
clk: tegra124: Add new peripheral clocks
clk: tegra124: Add common clk IDs to clk-id.h
clk: tegra: add TEGRA_PERIPH_NO_GATE
clk: tegra: add locking to periph clks
clk: tegra: Add periph regs bank X
clk: tegra: Add support for PLLSS
clk: tegra: move tegra20 to common infra
clk: tegra: move tegra30 to common infra
clk: tegra: introduce common gen4 super clock
clk: tegra: move PMC, fixed clocks to common files
...
Signed-off-by: Olof Johansson <olof@lixom.net>
net_dma can cause data to be copied to a stale mapping if a
copy-on-write fault occurs during dma. The application sees missing
data.
The following trace is triggered by modifying the kernel to WARN if it
ever triggers copy-on-write on a page that is undergoing dma:
WARNING: CPU: 24 PID: 2529 at lib/dma-debug.c:485 debug_dma_assert_idle+0xd2/0x120()
ioatdma 0000:00:04.0: DMA-API: cpu touching an active dma mapped page [pfn=0x16bcd9]
Modules linked in: iTCO_wdt iTCO_vendor_support ioatdma lpc_ich pcspkr dca
CPU: 24 PID: 2529 Comm: linbug Tainted: G W 3.13.0-rc1+ #353
00000000000001e5 ffff88016f45f688 ffffffff81751041 ffff88017ab0ef70
ffff88016f45f6d8 ffff88016f45f6c8 ffffffff8104ed9c ffffffff810f3646
ffff8801768f4840 0000000000000282 ffff88016f6cca10 00007fa2bb699349
Call Trace:
[<ffffffff81751041>] dump_stack+0x46/0x58
[<ffffffff8104ed9c>] warn_slowpath_common+0x8c/0xc0
[<ffffffff810f3646>] ? ftrace_pid_func+0x26/0x30
[<ffffffff8104ee86>] warn_slowpath_fmt+0x46/0x50
[<ffffffff8139c062>] debug_dma_assert_idle+0xd2/0x120
[<ffffffff81154a40>] do_wp_page+0xd0/0x790
[<ffffffff811582ac>] handle_mm_fault+0x51c/0xde0
[<ffffffff813830b9>] ? copy_user_enhanced_fast_string+0x9/0x20
[<ffffffff8175fc2c>] __do_page_fault+0x19c/0x530
[<ffffffff8175c196>] ? _raw_spin_lock_bh+0x16/0x40
[<ffffffff810f3539>] ? trace_clock_local+0x9/0x10
[<ffffffff810fa1f4>] ? rb_reserve_next_event+0x64/0x310
[<ffffffffa0014c00>] ? ioat2_dma_prep_memcpy_lock+0x60/0x130 [ioatdma]
[<ffffffff8175ffce>] do_page_fault+0xe/0x10
[<ffffffff8175c862>] page_fault+0x22/0x30
[<ffffffff81643991>] ? __kfree_skb+0x51/0xd0
[<ffffffff813830b9>] ? copy_user_enhanced_fast_string+0x9/0x20
[<ffffffff81388ea2>] ? memcpy_toiovec+0x52/0xa0
[<ffffffff8164770f>] skb_copy_datagram_iovec+0x5f/0x2a0
[<ffffffff8169d0f4>] tcp_rcv_established+0x674/0x7f0
[<ffffffff816a68c5>] tcp_v4_do_rcv+0x2e5/0x4a0
[..]
---[ end trace e30e3b01191b7617 ]---
Mapped at:
[<ffffffff8139c169>] debug_dma_map_page+0xb9/0x160
[<ffffffff8142bf47>] dma_async_memcpy_pg_to_pg+0x127/0x210
[<ffffffff8142cce9>] dma_memcpy_pg_to_iovec+0x119/0x1f0
[<ffffffff81669d3c>] dma_skb_copy_datagram_iovec+0x11c/0x2b0
[<ffffffff8169d1ca>] tcp_rcv_established+0x74a/0x7f0:
...the problem is that the receive path falls back to cpu-copy in
several locations and this trace is just one of the areas. A few
options were considered to fix this:
1/ sync all dma whenever a cpu copy branch is taken
2/ modify the page fault handler to hold off while dma is in-flight
Option 1 adds yet more cpu overhead to an "offload" that struggles to compete
with cpu-copy. Option 2 adds checks for behavior that is already documented as
broken when using get_user_pages(). At a minimum a debug mode is warranted to
catch and flag these violations of the dma-api vs get_user_pages().
Thanks to David for his reproducer.
Cc: <stable@vger.kernel.org>
Cc: Dave Jiang <dave.jiang@intel.com>
Cc: Vinod Koul <vinod.koul@intel.com>
Cc: Alexander Duyck <alexander.h.duyck@intel.com>
Reported-by: David Whipple <whipple@securedatainnovations.ch>
Acked-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
It might happen that a platform wants to use its DMA engine for
memcpy only, and then we have zero slave channels to initialize,
so allow the slave initialization to return zero.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
The channel allocated/released messages are very spammy and not really
interesting to users. Change them to "debug" level.
Signed-off-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Acked-by: Matt Porter <mporter@linaro.org>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
drivers/dma/mmp_tdma.c:236:8: warning: 'tdcr' may be used
uninitialized in this function [-Wuninitialized]
Reported-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
the driver is using unsigned long type for storing the channel register base
"reg_base", this leads to bunch of warns when we try to use this as pointer. So
better use an iomem pointer type for this variable
drivers/dma/mmp_tdma.c: In function 'mmp_tdma_chan_set_desc':
drivers/dma/mmp_tdma.c:143: warning: passing argument 2 of '__raw_writel' makes pointer from integer without a cast
drivers/dma/mmp_tdma.c:144: warning: passing argument 1 of '__raw_readl' makes pointer from integer without a cast
drivers/dma/mmp_tdma.c:144: warning: passing argument 2 of '__raw_writel' makes pointer from integer without a cast
drivers/dma/mmp_tdma.c: In function 'mmp_tdma_enable_chan':
drivers/dma/mmp_tdma.c:151: warning: passing argument 2 of '__raw_writel' makes pointer from integer without a cast
drivers/dma/mmp_tdma.c:153: warning: passing argument 1 of '__raw_readl' makes pointer from integer without a cast
drivers/dma/mmp_tdma.c:153: warning: passing argument 2 of '__raw_writel' makes pointer from integer without a cast
drivers/dma/mmp_tdma.c: In function 'mmp_tdma_disable_chan':
drivers/dma/mmp_tdma.c:160: warning: passing argument 1 of '__raw_readl' makes pointer from integer without a cast
drivers/dma/mmp_tdma.c:160: warning: passing argument 2 of '__raw_writel' makes pointer from integer without a cast
drivers/dma/mmp_tdma.c:164: warning: passing argument 2 of '__raw_writel' makes pointer from integer without a cast
drivers/dma/mmp_tdma.c: In function 'mmp_tdma_resume_chan':
drivers/dma/mmp_tdma.c:171: warning: passing argument 1 of '__raw_readl' makes pointer from integer without a cast
drivers/dma/mmp_tdma.c:171: warning: passing argument 2 of '__raw_writel' makes pointer from integer without a cast
drivers/dma/mmp_tdma.c: In function 'mmp_tdma_pause_chan':
drivers/dma/mmp_tdma.c:178: warning: passing argument 1 of '__raw_readl' makes pointer from integer without a cast
drivers/dma/mmp_tdma.c:178: warning: passing argument 2 of '__raw_writel' makes pointer from integer without a cast
drivers/dma/mmp_tdma.c: In function 'mmp_tdma_config_chan':
drivers/dma/mmp_tdma.c:263: warning: passing argument 2 of '__raw_writel' makes pointer from integer without a cast
drivers/dma/mmp_tdma.c: In function 'mmp_tdma_clear_chan_irq':
drivers/dma/mmp_tdma.c:269: warning: passing argument 1 of '__raw_readl' makes pointer from integer without a cast
drivers/dma/mmp_tdma.c:274: warning: passing argument 2 of '__raw_writel' makes pointer from integer without a cast
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Neaten code used as a template for other drivers.
Make the code more consistent with kernel styles.
o Convert #defines with (1<<foo) to BIT(foo)
o Alignment wrapping
o Logic inversions to put return at end of functions
o Convert devm_kzalloc with multiply to devm_kcalloc
o typo of Peripheral fix
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
This patch adds a new DMA_TYPE for SSI dual FIFO script, included
in SDMA firmware version 2. This script would allow SSI use dual
fifo mode to transimit/receive data without occasional hardware
underrun/overrun.
Signed-off-by: Nicolin Chen <b42378@freescale.com>
Acked-by: Kumar Gala <galak@codeaurora.org>
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
On i.MX5/6 series, SDMA is using new version firmware to support SSI
dual FIFO feature and HDMI Audio (i.MX6Q/DL only). Thus add it.
Signed-off-by: Nicolin Chen <b42378@freescale.com>
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
In order to be able to set a maximum segment size for the device we need to
allocate a dma_parameters struct for the device first.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
When a channel fails to initialise, we error out and clean up any
previously unregistered channels by walking the entire xordev->channels
array. Unfortunately, there are paths which end up storing an error
pointer in this array, which we then try and dereference in the cleanup
code, which causes an oops.
Fix this by avoiding writing invalid pointers to this array in the first
place.
Tested-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
The driver-specific unmap code was removed in:
commit 54f8d501e8
Author: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Date: Fri Oct 18 19:35:32 2013 +0200
dmaengine: remove DMA unmap from drivers
which had the side-effect of not unmapping the self-test mappings.
Fix this by using dmaengine_unmap_data in the self-test routines.
In addition, since dmaengine_unmap() assumes that all mappings were created
with dma_map_page, this commit changes the single mapping to a page mapping
to avoid an incorrect unmapping of the memcpy self-test.
The allocation could be changed to be alloc_page(), but sticking to kmalloc
results in a less intrusive patch. The size of the test buffer is increased,
since dma_map_page() seem to fail when the source and destination pages are
the same page.
Signed-off-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
The higher order mempools support raid operations, and we want to
disable them when raid support is not enabled. Making them conditional
on ASYNC_TX_DMA is not sufficient as other users (specifically dmatest)
will also issue raid operations. Make raid drivers explicitly request
that the core carry the higher order pools.
Reported-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Tested-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
drivers/dma/dmatest.c:543:11: warning: passing argument 1 of 'virt_to_phys' makes pointer from integer without a cast [enabled by default]
mips expects virt_to_phys() to take a pointer. Fix up the types accordingly.
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
drivers/dma/fsldma.c: In function 'fsldma_cleanup_descriptor':
drivers/dma/fsldma.c:860:6: warning: unused variable 'len' [-Wunused-variable]
drivers/dma/fsldma.c:859:13: warning: unused variable 'dst' [-Wunused-variable]
drivers/dma/fsldma.c:858:13: warning: unused variable 'src' [-Wunused-variable]
drivers/dma/fsldma.c:857:17: warning: unused variable 'dev' [-Wunused-variable]
- due to unmap changes
drivers/dma/fsldma.c: In function 'fsl_dma_tx_submit':
drivers/dma/fsldma.c:428:2: warning: 'cookie' may be used uninitialized in this function [-Wuninitialized]
- long standing warning
Cc: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Cc: Li Yang <leoli@freescale.com>
Cc: Zhang Wei <zw@zh-kernel.org>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
drivers/dma/ppc4xx/adma.c:1507:6: warning: unused variable 'i' [-Wunused-variable]
- due to unmap reworks
drivers/dma/ppc4xx/adma.c:3900:2: warning: format '%s' expects a matching 'char *' argument [-Wformat]
- due to memset removal
drivers/dma/ppc4xx/adma.c:538:13: warning: 'ppc440spe_desc_init_memset' defined but not used [-Wunused-function]
- due to memset removal
Cc: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
commit 54f8d501e8 ('dmaengine: remove DMA unmap from drivers')
refactored some code which resulted in an unused function in the at_hdmac
driver:
drivers/dma/at_hdmac_regs.h:350:23: warning: 'chan2parent' defined but
not used [-Wunused-function]
Fixes: 54f8d501e8 ('dmaengine: remove DMA unmap from drivers')
Signed-off-by: Olof Johansson <olof@lixom.net>
Cc: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Acked-by: Vinod Koul <vinod.koul@Intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
The following commit:
54f8d501e8 dmaengine: remove DMA unmap from drivers
removed the last caller to mv_desc_get_dest_addr(), creating the
warning:
drivers/dma/mv_xor.c:57:12: warning: mv_desc_get_dest_addr defined
but not used [-Wunused-function]
Remove it.
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Acked-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
sram driver can be used by many chips besides CPU_MMP2, and so build
it alone. Also need to select MMP_SRAM for MMP_TDMA driver.
Reported-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Qiao Zhou <zhouqiao@marvell.com>
Signed-off-by: Haojian Zhuang <haojian.zhuang@gmail.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
Call of_dma_controller_register() so that DMA clients can look up the
Tegra DMA controller using standard APIs. This requires the of_xlate()
function to save off the DMA slave ID, and for tegra_dma_slave_config()
not to over-write this information; once DMA client drivers are converted
to dma_request_slave_channel() and DT-based lookups, they won't set this
field of struct dma_slave_config anymore.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Thierry Reding <treding@nvidia.com>
Tegra's clock driver now provides an implementation of the common
reset API (include/linux/reset.h). Use this instead of the old Tegra-
specific API; that will soon be removed.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Reviewed-by: Thierry Reding <treding@nvidia.com>
Acked-by: Dan Williams <dan.j.williams@intel.com>
Acked-by: Vinod Koul <vinod.koul@intel.com>
mmp_pdma.c implements a custom of_xlate() function that is 95% identical
to what Tegra will need. Create a function to implement the common part,
so everyone doesn't just cut/paste the implementation.
Cc: Dan Williams <dan.j.williams@intel.com>
Cc: Vinod Koul <vinod.koul@intel.com>
Cc: Lars-Peter Clausen <lars@metafoo.de>
Cc: dmaengine@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
dma_request_slave_channel() simply returns NULL whenever DMA channel
lookup fails. Lookup could fail for two distinct reasons:
a) No DMA specification exists for the channel name.
This includes situations where no DMA specifications exist at all, or
other general lookup problems.
b) A DMA specification does exist, yet the driver for that channel is not
yet registered.
Case (b) should trigger deferred probe in client drivers. However, since
they have no way to differentiate the two situations, it cannot.
Implement new function dma_request_slave_channel_reason(), which performs
identically to dma_request_slave_channel(), except that it returns an
error-pointer rather than NULL, which allows callers to detect when
deferred probe should occur.
Eventually, all drivers should be converted to this new API, the old API
removed, and the new API renamed to the more desirable name. This patch
doesn't convert the existing API and all drivers in one go, since some
drivers call dma_request_slave_channel() then dma_request_channel() if
that fails. That would require either modifying dma_request_channel() in
the same way, or adding extra error-handling code to all affected
drivers, and there are close to 100 drivers using the other API, rather
than just the 15-20 or so that use dma_request_slave_channel(), which
might be tenable in a single patch.
acpi_dma_request_slave_chan_by_name() doesn't currently implement
deferred probe. It should, but this will be addressed later.
Acked-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
This driver missed the dma unmap conversion. Replace
s3c24xx_dma_unmap_buffers with dma_descriptor_unmap.
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
drivers/dma/amba-pl08x.c: In function 'pl08x_desc_free':
drivers/dma/amba-pl08x.c:1173:2: warning: passing argument 1 of 'dma_descriptor_unmap' from incompatible pointer type
include/linux/dmaengine.h:476:91: note: expected 'struct dma_async_tx_descriptor *' but argument is of type 'struct pl08x_txd *'
Fixes: d38a8c622a ("dmaengine: prepare for generic 'unmap' data")
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Plane information should be initialized when halted.
It may restart from the wrong plane without this patch.
Reviewed-by: Max Filippov <max.filippov@cogentembedded.com>
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Acked-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
The device busy check method is different between
single and double planes.
It will always return "busy" without this patch
if channel used as double plane.
Reviewed-by: Max Filippov <max.filippov@cogentembedded.com>
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Acked-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
shdma_chan_probe() can set max transfer size,
but it will be PAGE_SIZE with out this patch.
Reviewed-by: Max Filippov <max.filippov@cogentembedded.com>
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Acked-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Use the recently introduced DMA_COMPLETE instead of DMA_SUCCESS.
Without this patch we get the following build error:
drivers/dma/s3c24xx-dma.c: In function ‘s3c24xx_dma_tx_status’:
drivers/dma/s3c24xx-dma.c:798:13: error: ‘DMA_SUCCESS’ undeclared
(first use in this function)
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Acked-by: Heiko Stuebner <heiko@sntech.de>
Acked-by: Kukjin Kim <kgene@kernel.org>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
This is used for MSP (audio) devices which is about to be fully DT:ed.
Acked-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Pull slave-dmaengine changes from Vinod Koul:
"This brings for slave dmaengine:
- Change dma notification flag to DMA_COMPLETE from DMA_SUCCESS as
dmaengine can only transfer and not verify validaty of dma
transfers
- Bunch of fixes across drivers:
- cppi41 driver fixes from Daniel
- 8 channel freescale dma engine support and updated bindings from
Hongbo
- msx-dma fixes and cleanup by Markus
- DMAengine updates from Dan:
- Bartlomiej and Dan finalized a rework of the dma address unmap
implementation.
- In the course of testing 1/ a collection of enhancements to
dmatest fell out. Notably basic performance statistics, and
fixed / enhanced test control through new module parameters
'run', 'wait', 'noverify', and 'verbose'. Thanks to Andriy and
Linus [Walleij] for their review.
- Testing the raid related corner cases of 1/ triggered bugs in
the recently added 16-source operation support in the ioatdma
driver.
- Some minor fixes / cleanups to mv_xor and ioatdma"
* 'next' of git://git.infradead.org/users/vkoul/slave-dma: (99 commits)
dma: mv_xor: Fix mis-usage of mmio 'base' and 'high_base' registers
dma: mv_xor: Remove unneeded NULL address check
ioat: fix ioat3_irq_reinit
ioat: kill msix_single_vector support
raid6test: add new corner case for ioatdma driver
ioatdma: clean up sed pool kmem_cache
ioatdma: fix selection of 16 vs 8 source path
ioatdma: fix sed pool selection
ioatdma: Fix bug in selftest after removal of DMA_MEMSET.
dmatest: verbose mode
dmatest: convert to dmaengine_unmap_data
dmatest: add a 'wait' parameter
dmatest: add basic performance metrics
dmatest: add support for skipping verification and random data setup
dmatest: use pseudo random numbers
dmatest: support xor-only, or pq-only channels in tests
dmatest: restore ability to start test at module load and init
dmatest: cleanup redundant "dmatest: " prefixes
dmatest: replace stored results mechanism, with uniform messages
Revert "dmatest: append verify result to results"
...
Pull dmaengine changes from Dan
1/ Bartlomiej and Dan finalized a rework of the dma address unmap
implementation.
2/ In the course of testing 1/ a collection of enhancements to dmatest
fell out. Notably basic performance statistics, and fixed / enhanced
test control through new module parameters 'run', 'wait', 'noverify',
and 'verbose'. Thanks to Andriy and Linus for their review.
3/ Testing the raid related corner cases of 1/ triggered bugs in the
recently added 16-source operation support in the ioatdma driver.
4/ Some minor fixes / cleanups to mv_xor and ioatdma.
Conflicts:
drivers/dma/dmatest.c
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Pull trivial tree updates from Jiri Kosina:
"Usual earth-shaking, news-breaking, rocket science pile from
trivial.git"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial: (23 commits)
doc: usb: Fix typo in Documentation/usb/gadget_configs.txt
doc: add missing files to timers/00-INDEX
timekeeping: Fix some trivial typos in comments
mm: Fix some trivial typos in comments
irq: Fix some trivial typos in comments
NUMA: fix typos in Kconfig help text
mm: update 00-INDEX
doc: Documentation/DMA-attributes.txt fix typo
DRM: comment: `halve' -> `half'
Docs: Kconfig: `devlopers' -> `developers'
doc: typo on word accounting in kprobes.c in mutliple architectures
treewide: fix "usefull" typo
treewide: fix "distingush" typo
mm/Kconfig: Grammar s/an/a/
kexec: Typo s/the/then/
Documentation/kvm: Update cpuid documentation for steal time and pv eoi
treewide: Fix common typo in "identify"
__page_to_pfn: Fix typo in comment
Correct some typos for word frequency
clk: fixed-factor: Fix a trivial typo
...
Despite requesting two memory resources, called 'base' and 'high_base', the
driver uses explicitly only the former. The latter is being used implicitly
by addressing at offset +0x200, which in practice accesses high_base.
In other words, the current driver breaks if the second memory resource
is ever place at an offset different from +0x200.
This patch fixes the above by defining the registers with the offset from
high_base, and use high_base explicitly where appropriate.
Signed-off-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Acked-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
This mmio address is checked at probe-time, which makes this test
redundant. Let's just remove it.
Acked-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
The implementation of ioat3_irq_reinit has two bugs:
1/ The mode is incorrectly set to MSIX for the MSI case
2/ The 'dev_id' parameter to free_irq is the ioatdma_device not the channel in
the msi and intx case
Include a small cleanup to clarify that ioat3_irq_reinit is only for bwd
hardware
Cc: Dave Jiang <dave.jiang@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Once we have determined that we will not have all of our desired msix
vectors there is no point in attempting a single msix allocation. The
driver will already need to read registers to determine the source of
the interrupt the fact that it is msix is moot. Fallback directly to
msi.
Reported-by: Alexander Gordeev <agordeev@redhat.com>
Cc: Dave Jiang <dave.jiang@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Use a single cache for all sed allocations. No need to make it per
channel. This also avoids the slub_debug warnings for multiple caches
with the same name.
Switching to dmam_pool_create() to fix leaking the dma pools on
initialization failure and lets us kill ioat3_dma_remove().
Cc: Dave Jiang <dave.jiang@intel.com>
Acked-by: Dave Jiang <dave.jiang@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
When performing continuations there are implied sources that need to be
added to the source count. Quoting dma_set_maxpq:
/* dma_maxpq - reduce maxpq in the face of continued operations
* @dma - dma device with PQ capability
* @flags - to check if DMA_PREP_CONTINUE and DMA_PREP_PQ_DISABLE_P are set
*
* When an engine does not support native continuation we need 3 extra
* source slots to reuse P and Q with the following coefficients:
* 1/ {00} * P : remove P from Q', but use it as a source for P'
* 2/ {01} * Q : use Q to continue Q' calculation
* 3/ {00} * Q : subtract Q from P' to cancel (2)
*
* In the case where P is disabled we only need 1 extra source:
* 1/ {01} * Q : use Q to continue Q' calculation
*/
...fix the selection of the 16 source path to take these implied sources
into account.
Note this also kills the BUG_ON(src_cnt < 9) check in
__ioat3_prep_pq16_lock(). Besides not accounting for implied sources
the check is redundant given we already made the path selection.
Cc: <stable@vger.kernel.org>
Cc: Dave Jiang <dave.jiang@intel.com>
Acked-by: Dave Jiang <dave.jiang@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
The array to lookup the sed pool based on the number of sources
(pq16_idx_to_sedi) is 16 entries and expects a max source index.
However, we pass the total source count which runs off the end of the
array when src_cnt == 16. The minimal fix is to just pass src_cnt-1,
but given we know the source count is > 8 we can just calculate the sed
pool by (src_cnt - 2) >> 3.
Cc: Dave Jiang <dave.jiang@intel.com>
Cc: <stable@vger.kernel.org>
Acked-by: Dave Jiang <dave.jiang@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Commit 48a9db4 (3.11) removed the memset op in the xor selftest for ioatdma.
The issue is that with the removal of that op, it never replaced the memset
with a CPU memset. The memory being operated on is expected to be zeroes but
was not. This is causing the xor selftest to fail.
Cc: <stable@vger.kernel.org>
Signed-off-by: Dave Jiang <dave.jiang@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Verbose mode turns on test success messages, by default we only output
test summaries and failure results.
Also cleaned up some stray quotes, leftover from putting the result
message format string all on one line.
Cc: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Remove the open coded unmap and add coverage for this core functionality
to dmatest.
Also fixes up a couple places where we leaked dma mappings.
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Allows for scripting test runs by module load / unload. Prevent module
load from returning until 'iterations' (finite) tests have completed, or
cause reads of the 'wait' parameter in sysfs to pause until the tests
are done.
Also killed the local waitqueue since we can just let the thread exit
naturally as long as we hold a reference.
Cc: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Add iops and throughput to the summary output.
Acked-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Towards enabling dmatest to checkout performance add a 'noverify' mode.
Acked-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
There is no need for dmatest to drain the entropy pool.
It would be nice to one day have repeatable runs, but would need a
larger rework to synchronize and order calls to the rng across test
threads.
Acked-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Currently we only test raid channels that happen to also have 'copy'
capability. Search for capable channels that do not have DMA_MEMCPY.
Note the return value from run_threaded_test never really made sense
because it could return errors after successfully starting tests. We
already have the test results per channel so missing channels can be
detected at that time.
Acked-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
1/ move 'run' control to a module parameter so we can do:
modprobe dmatest run=1. With this moved the rest of the debugfs
boilerplate can go.
2/ Fix parameter initialization. Previously the test was being started
without taking the parameters into account in the built-in case.
Also killed off the '__' version of some routines. The new rule is just
hold the lock when calling a *threaded_test() routine.
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Cc: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
...now that we have a common pr_fmt.
Acked-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
For long running tests the tracking results in a memory leak for the "ok"
results, and for the failures the kernel log should be sufficient. Provide a
uniform format for error messages so they can be easily parsed and remove the
debugfs file.
Cc: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
This reverts commit d86b2f298e.
The kernel log buffer is sufficient for collecting test results. The
current logging OOMs the machine on long running tests, and usually only
the first error is relevant. It is better to stop on error and parse
the kernel output. If output volume becomes an issue we can always
investigate using trace messages.
Cc: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Remove support for DMA unmapping from drivers as it is no longer
needed (DMA core code is now handling it).
Cc: Vinod Koul <vinod.koul@intel.com>
Cc: Tomasz Figa <t.figa@samsung.com>
Cc: Dave Jiang <dave.jiang@intel.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
[djbw: fix up chan2parent() unused warning in drivers/dma/dw/core.c]
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Use the generic unmap object to unmap dma buffers.
Cc: Vinod Koul <vinod.koul@intel.com>
Cc: Tomasz Figa <t.figa@samsung.com>
Cc: Dave Jiang <dave.jiang@intel.com>
Reported-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
[bzolnier: keep temporary dma_dest array in do_async_gen_syndrome()]
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Hang a common 'unmap' object off of dma descriptors for the purpose of
providing a unified unmapping interface. The lifetime of a mapping may
span multiple descriptors, so these unmap objects are reference counted
by related descriptor.
Cc: Vinod Koul <vinod.koul@intel.com>
Cc: Tomasz Figa <t.figa@samsung.com>
Cc: Dave Jiang <dave.jiang@intel.com>
[bzolnier: fix IS_ENABLED() check]
[bzolnier: fix release ordering in dmaengine_destroy_unmap_pool()]
[bzolnier: fix check for success in dmaengine_init_unmap_pool()]
[bzolnier: use mempool_free() instead of kmem_cache_free()]
[bzolnier: add missing unmap->len initializations]
[bzolnier: add __init tag to dmaengine_init_unmap_pool()]
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
[djbw: move DMAENGINE=n support to this patch for async_tx]
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Add a hook for a common dma unmap implementation to enable removal of
the per driver custom unmap code. (A reworked version of Bartlomiej
Zolnierkiewicz's patches to remove the custom callbacks and the size
increase of dma_async_tx_descriptor for drivers that don't care about
raid).
Cc: Vinod Koul <vinod.koul@intel.com>
Cc: Tomasz Figa <t.figa@samsung.com>
Cc: Dave Jiang <dave.jiang@intel.com>
[bzolnier: prepare pl330 driver for adding missing unmap while at it]
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Copying from page to page (dma_async_memcpy_pg_to_pg) is the superset,
make the other two apis use that one in preparation for providing a
common dma unmap implementation. The common implementation just wants
to assume all buffers are mapped with dma_map_page().
Cc: Vinod Koul <vinod.koul@intel.com>
Cc: Tomasz Figa <t.figa@samsung.com>
Cc: Dave Jiang <dave.jiang@intel.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Pull DMA mask updates from Russell King:
"This series cleans up the handling of DMA masks in a lot of drivers,
fixing some bugs as we go.
Some of the more serious errors include:
- drivers which only set their coherent DMA mask if the attempt to
set the streaming mask fails.
- drivers which test for a NULL dma mask pointer, and then set the
dma mask pointer to a location in their module .data section -
which will cause problems if the module is reloaded.
To counter these, I have introduced two helper functions:
- dma_set_mask_and_coherent() takes care of setting both the
streaming and coherent masks at the same time, with the correct
error handling as specified by the API.
- dma_coerce_mask_and_coherent() which resolves the problem of
drivers forcefully setting DMA masks. This is more a marker for
future work to further clean these locations up - the code which
creates the devices really should be initialising these, but to fix
that in one go along with this change could potentially be very
disruptive.
The last thing this series does is prise away some of Linux's addition
to "DMA addresses are physical addresses and RAM always starts at
zero". We have ARM LPAE systems where all system memory is above 4GB
physical, hence having DMA masks interpreted by (eg) the block layers
as describing physical addresses in the range 0..DMAMASK fails on
these platforms. Santosh Shilimkar addresses this in this series; the
patches were copied to the appropriate people multiple times but were
ignored.
Fixing this also gets rid of some ARM weirdness in the setup of the
max*pfn variables, and brings ARM into line with every other Linux
architecture as far as those go"
* 'for-linus-dma-masks' of git://git.linaro.org/people/rmk/linux-arm: (52 commits)
ARM: 7805/1: mm: change max*pfn to include the physical offset of memory
ARM: 7797/1: mmc: Use dma_max_pfn(dev) helper for bounce_limit calculations
ARM: 7796/1: scsi: Use dma_max_pfn(dev) helper for bounce_limit calculations
ARM: 7795/1: mm: dma-mapping: Add dma_max_pfn(dev) helper function
ARM: 7794/1: block: Rename parameter dma_mask to max_addr for blk_queue_bounce_limit()
ARM: DMA-API: better handing of DMA masks for coherent allocations
ARM: 7857/1: dma: imx-sdma: setup dma mask
DMA-API: firmware/google/gsmi.c: avoid direct access to DMA masks
DMA-API: dcdbas: update DMA mask handing
DMA-API: dma: edma.c: no need to explicitly initialize DMA masks
DMA-API: usb: musb: use platform_device_register_full() to avoid directly messing with dma masks
DMA-API: crypto: remove last references to 'static struct device *dev'
DMA-API: crypto: fix ixp4xx crypto platform device support
DMA-API: others: use dma_set_coherent_mask()
DMA-API: staging: use dma_set_coherent_mask()
DMA-API: usb: use new dma_coerce_mask_and_coherent()
DMA-API: usb: use dma_set_coherent_mask()
DMA-API: parport: parport_pc.c: use dma_coerce_mask_and_coherent()
DMA-API: net: octeon: use dma_coerce_mask_and_coherent()
DMA-API: net: nxp/lpc_eth: use dma_coerce_mask_and_coherent()
...
Make the driver DMA unmap also source buffers by itself
(currently it DMA unmaps only destination buffers) as
a preparation for introducing generic 'ummap' data.
Cc: Dan Williams <dan.j.williams@intel.com>
Cc: Vinod Koul <vinod.koul@intel.com>
Cc: Tomasz Figa <t.figa@samsung.com>
Cc: Dave Jiang <dave.jiang@intel.com>
Cc: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Acked-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
On 64 bit systems GCC warns that:
drivers/dma/pl330.c: In function ‘pl330_filter’:
drivers/dma/pl330.c:2317:21: warning: cast from pointer to integer of different size [-Wpointer-to-int-cast]
It's harmless and I have casted it away.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
There are only AMBA_NR_IRQS (2) elements in adev->irq[]. This code
maybe works if the there is a zero directly after the array.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
mxs dma channel hardware reset command is not reliable and can cause
a channel stall. The only way to fix the channel stall is a DMA engine
reset.
To avoid channel resets we use the hardware semaphore counter. For each
transmitted segment, the DMA channel will decrease the counter by one.
To use this mechanism with cyclic DMA, we need to increase the semaphore
counter with each completed DMA command in the interrupt handler. To
avoid any interruptions between the DMA transfers, the semaphore counter
is initialized with 2. This way the counter can be increased in the
interrupt handler without an influence on the transfer of the DMA
engine.
When disabling the channel, we stop increasing the semaphore counter in
the interrupt handler.
This patch was tested on i.MX28 with the SAIF DMA channel.
Signed-off-by: Markus Pargmann <mpa@pengutronix.de>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
After a channel reset, the channel stops running automatically. The
state update was missing so that a channel perperation right after a
channel reset failed.
Signed-off-by: Markus Pargmann <mpa@pengutronix.de>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
This is no official errata, but I noticed that the channel reset may
stop working if the DMA state engine is in the READ_FLUSH state.
This patch uses the channel debug1 register to wait for the DMA
statemachine to leave the READ_FLUSH state. After that we can continue
to reset the channel.
Tested on i.MX28.
Signed-off-by: Markus Pargmann <mpa@pengutronix.de>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Use the channel's buffer address register to calculate correct residue
value for tx_status.
Signed-off-by: Markus Pargmann <mpa@pengutronix.de>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
The DMA interrupt handler uses its controll registers to handle all
available channel interrupts it can find.
This patch changes it to handle only one interrupt by directly mapping
irq number to channel. It also includes a cleanup of the ctrl-register
usage.
Signed-off-by: Markus Pargmann <mpa@pengutronix.de>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
This patch adds support to 8-channel DMA engine, thus the driver works for both
the new 8-channel and the legacy 4-channel DMA engines.
Signed-off-by: Hongbo Zhang <hongbo.zhang@freescale.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
This resolves a number of warnings such as the below when building with
64-bit dma_addr_t on arm:
drivers/dma/imx-sdma.c:1092:3: warning: format '%x' expects argument of
type 'unsigned int', but argument 6 has type 'dma_addr_t' [-Wformat=]
..by upcasting to u64 and using %llx.
Signed-off-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
This resolves a number of warnings such as the below when building with
64-bit dma_addr_t on arm:
drivers/dma/ipu/ipu_idmac.c:1235:2: warning: format '%x' expects argument
of type 'unsigned int', but argument 5 has type 'dma_addr_t' [-Wformat=]
..by upcasting to u64 and using %llx.
Signed-off-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
fixing of freeing descriptor memory was applied twice, so remove the one
duplicate
Reported-by: Wing-Keung Wang <wingkeung.wang@gmail.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Since gen_pool_dma_alloc() is introduced, we implement it to simplify code.
Signed-off-by: Nicolin Chen <b42378@freescale.com>
Cc: Dan Williams <dan.j.williams@intel.com>
Cc: Vinod Koul <vinod.koul@intel.com>
Cc: Grant Likely <grant.likely@linaro.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Return code of pm_runtime_get_sync() > 0 is not an error and may happen.
Noticed during rmmod & modprobe testing.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Most of the logic here is try and error since what actually happens does
not match the trm or I miss read it.
My first assumption was that the queue on which the tear-down descriptor
completes (their own complete queue vs "active descriptor" complete
queue) depends on the transfer direction. This seems not to be true
because I manage to trigger
| WARN_ON(c->desc_phys != desc_phys);
and the other few were fine means the tear-down descriptor was valid but
on different queue.
This patch changes the logic here to look on both queues for the
descriptor.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Use cppi41_pop_desc() when appropriate instead of open-coding the same
functionality again. That makes the code more readable. The function has
to be moved some lines up for this change.
Signed-off-by: Daniel Mack <zonque@gmail.com>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
With active users over suspend/resume cycles, it turns out that
more registers, in particular DMA_TDFDQ and RXHPCRA0, have to be
restored on resume.
Signed-off-by: Daniel Mack <zonque@gmail.com>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
usual for this cycle with lots of clean-up.
- Cross arch clean-up and consolidation of early DT scanning code.
- Clean-up and removal of arch prom.h headers. Makes arch specific
prom.h optional on all but Sparc.
- Addition of interrupts-extended property for devices connected to
multiple interrupt controllers.
- Refactoring of DT interrupt parsing code in preparation for deferred
probe of interrupts.
- ARM cpu and cpu topology bindings documentation.
- Various DT vendor binding documentation updates.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)
iQEcBAABAgAGBQJSgPQ4AAoJEMhvYp4jgsXif28H/1WkrXq5+lCFQZF8nbYdE2h0
R8PsfiJJmAl6/wFgQTsRel+ScMk2hiP08uTyqf2RLnB1v87gCF7MKVaLOdONfUDi
huXbcQGWCmZv0tbBIklxJe3+X3FIJch4gnyUvPudD1m8a0R0LxWXH/NhdTSFyB20
PNjhN/IzoN40X1PSAhfB5ndWnoxXBoehV/IVHVDU42vkPVbVTyGAw5qJzHW8CLyN
2oGTOalOO4ffQ7dIkBEQfj0mrgGcODToPdDvUQyyGZjYK2FY2sGrjyquir6SDcNa
Q4gwatHTu0ygXpyphjtQf5tc3ZCejJ/F0s3olOAS1ahKGfe01fehtwPRROQnCK8=
=GCbY
-----END PGP SIGNATURE-----
Merge tag 'devicetree-for-3.13' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux
Pull devicetree updates from Rob Herring:
"DeviceTree updates for 3.13. This is a bit larger pull request than
usual for this cycle with lots of clean-up.
- Cross arch clean-up and consolidation of early DT scanning code.
- Clean-up and removal of arch prom.h headers. Makes arch specific
prom.h optional on all but Sparc.
- Addition of interrupts-extended property for devices connected to
multiple interrupt controllers.
- Refactoring of DT interrupt parsing code in preparation for
deferred probe of interrupts.
- ARM cpu and cpu topology bindings documentation.
- Various DT vendor binding documentation updates"
* tag 'devicetree-for-3.13' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux: (82 commits)
powerpc: add missing explicit OF includes for ppc
dt/irq: add empty of_irq_count for !OF_IRQ
dt: disable self-tests for !OF_IRQ
of: irq: Fix interrupt-map entry matching
MIPS: Netlogic: replace early_init_devtree() call
of: Add Panasonic Corporation vendor prefix
of: Add Chunghwa Picture Tubes Ltd. vendor prefix
of: Add AU Optronics Corporation vendor prefix
of/irq: Fix potential buffer overflow
of/irq: Fix bug in interrupt parsing refactor.
of: set dma_mask to point to coherent_dma_mask
of: add vendor prefix for PHYTEC Messtechnik GmbH
DT: sort vendor-prefixes.txt
of: Add vendor prefix for Cadence
of: Add empty for_each_available_child_of_node() macro definition
arm/versatile: Fix versatile irq specifications.
of/irq: create interrupts-extended property
microblaze/pci: Drop PowerPC-ism from irq parsing
of/irq: Create of_irq_parse_and_map_pci() to consolidate arch code.
of/irq: Use irq_of_parse_and_map()
...
Using the PaRAM configuration function that we split for reuse by the
different DMA types, we implement Cyclic DMA support.
For the cyclic case, we pass different configuration parameters to this
function, and handle all the Cyclic-specific functionality separately.
Callbacks to the DMA users are handled using vchan_cyclic_callback in
the virt-dma layer. Linking is handled the same way as the slave SG case
except for the last slot where we link it back to the first one in a
cyclic fashion.
For continuity, we check for cases where no.of periods is great than the
MAX number of slots the driver can allocate for a particular descriptor
and error out on such cases.
Signed-off-by: Joel Fernandes <joelf@ti.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Commit b5b4bb3f6a (of: only include prom.h on sparc) removed implicit
includes of of_*.h headers by powerpc's prom.h. Some components were
missed in initial clean-up patch, so add the necessary includes to fix
powerpc builds.
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Tejun Heo <tj@kernel.org>
Cc: Matt Mackall <mpm@selenic.com>
Cc: Herbert Xu <herbert@gondor.apana.org.au>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Vinod Koul <vinod.koul@intel.com>
Cc: Dan Williams <dan.j.williams@intel.com>
Cc: linuxppc-dev@lists.ozlabs.org
Cc: linux-ide@vger.kernel.org
Cc: linux-crypto@vger.kernel.org
Updates of SoC-near drivers and other driver updates that makes more sense to
take through our tree. In this case it's involved:
- Some Davinci driver updates that has required corresponding platform code
changes (gpio mostly)
- CCI bindings and a few driver updates
- Marvell mvebu patches for PCI MSI support (could have gone through the PCI
tree for this release, but they were acked by Bjorn for 3.12 so we kept them
through arm-soc).
- Marvell dove switch-over to DT-based PCIe configuration
- Misc updates for Samsung platform dmaengine drivers
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)
iQIcBAABAgAGBQJSgBr3AAoJEIwa5zzehBx3QkEP/i0bm4V+AkNV/EXPxqXDf0Re
WIKao/0UjqEfTLSx38F+GlsCdpiPkicPZls0tzAiuqWycx+gMiUlJ7XB+tFmQRk1
RS4KzPQeALFVapjVLtid/Bls9OVI8NcNL1Dx7FISTURzrSzB+kXg7KIsq92SootW
AHUMZbPQNqZoTYcRo9EFEBCm+7QwH1GmWIo5tID6sRhPIsj0xXrw/zOQDK4WDbkv
ZmlR2PNdVTYNuKsWtBcINU5GGNcTCEpnLlHZ9QzVOGyP2M/S93FQdjjm+vDxBRC6
0WsCCFzWc2boSyKrah8xcb7kox7+8HMXUFFAARfOJxvqnMpDCSQnQv0Hb2SiwbkF
7AW90lj+E9KqleSVy1fjGOvx2MV8vhqFMoCYg2TXW2546JADGnCw2JOILfRcqMox
JqIpc84Yhmnv2qFCDxdj9hLYqvhH3RjdLzaLhSfMPc8pjP1StMJzcNi7tN46KVqg
60wU7DvJ0uWfacUGj7VBn88XiZvvJjO/laxj5UcZlS+kQzsysw4Tbriz9UeJK1yl
N0LBl4iA9xn5aUEI/1kL8xzX+h01VodMCe6jIz3JBdE66vCX6d2Tf+zYpNHiGCsH
kBfOpuYc1jVW6qTYqDWgO3IVdDdSGa096AF5vR3MOmtDidblq9QVVxxhDwscqO6J
O0RIcxwZAzQGcO4F50PL
=yCsK
-----END PGP SIGNATURE-----
Merge tag 'drivers-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM driver updates from Olof Johansson:
"Updates of SoC-near drivers and other driver updates that makes more
sense to take through our tree. In this case it's involved:
- Some Davinci driver updates that has required corresponding
platform code changes (gpio mostly)
- CCI bindings and a few driver updates
- Marvell mvebu patches for PCI MSI support (could have gone through
the PCI tree for this release, but they were acked by Bjorn for
3.12 so we kept them through arm-soc).
- Marvell dove switch-over to DT-based PCIe configuration
- Misc updates for Samsung platform dmaengine drivers"
* tag 'drivers-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (32 commits)
ARM: S3C24XX: add dma pdata for s3c2410, s3c2440 and s3c2442
dmaengine: s3c24xx-dma: add support for the s3c2410 type of controller
ARM: S3C24XX: Fix possible dma selection warning
PCI: mvebu: make local functions static
PCI: mvebu: add I/O access wrappers
PCI: mvebu: Dynamically detect if the PEX link is up to enable hot plug
ARM: mvebu: fix gated clock documentation
ARM: dove: remove legacy pcie and clock init
ARM: dove: switch to DT probed mbus address windows
ARM: SAMSUNG: set s3c24xx_dma_filter for s3c64xx-spi0 device
ARM: S3C24XX: add platform-devices for new dma driver for s3c2412 and s3c2443
dmaengine: add driver for Samsung s3c24xx SoCs
ARM: S3C24XX: number the dma clocks
PCI: mvebu: add support for Marvell Dove SoCs
PCI: mvebu: add support for reset on GPIO
PCI: mvebu: remove subsys_initcall
PCI: mvebu: increment nports only for registered ports
PCI: mvebu: move clock enable before register access
PCI: mvebu: add support for MSI
irqchip: armada-370-xp: implement MSI support
...
New and updated SoC support. Among the things new for this release are:
- More support for the AM33xx platforms from TI
- Tegra 124 support, and some updates to older tegra families as well
- imx cleanups and updates across the board
- A rename of Broadcom's Mobile platforms which were introduced as ARCH_BCM,
and turned out to be too broad a name. New name is ARCH_BCM_MOBILE.
- A whole bunch of updates and fixes for integrator, making the platform code
more modern and switches over to DT-only booting.
- Support for two new Renesas shmobile chipsets. Next up for them is more work
on consolidation instead of introduction of new non-multiplatform SoCs, we're
all looking forward to that!
- Misc cleanups for older Samsung platforms, some Allwinner updates, etc.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=WYJl
-----END PGP SIGNATURE-----
Merge tag 'soc-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC platform changes from Olof Johansson:
"New and updated SoC support. Among the things new for this release
are:
- More support for the AM33xx platforms from TI
- Tegra 124 support, and some updates to older tegra families as well
- imx cleanups and updates across the board
- A rename of Broadcom's Mobile platforms which were introduced as
ARCH_BCM, and turned out to be too broad a name. New name is
ARCH_BCM_MOBILE.
- A whole bunch of updates and fixes for integrator, making the
platform code more modern and switches over to DT-only booting.
- Support for two new Renesas shmobile chipsets. Next up for them is
more work on consolidation instead of introduction of new
non-multiplatform SoCs, we're all looking forward to that!
- Misc cleanups for older Samsung platforms, some Allwinner updates,
etc"
* tag 'soc-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (159 commits)
ARM: bcm281xx: Add ARCH_BCM_MOBILE to bcm config
ARM: bcm_defconfig: Run "make savedefconfig"
ARM: bcm281xx: Add ARCH Timers to config
rename ARCH_BCM to ARCH_BCM_MOBILE (mach-bcm)
ARM: vexpress: Enable platform-specific options in defconfig
ARM: vexpress: Make defconfig work again
ARM: sunxi: remove .init_time hooks
ARM: imx: enable suspend for imx6sl
ARM: imx: ensure dsm_request signal is not asserted when setting LPM
ARM: imx6q: call WB and RBC configuration from imx6q_pm_enter()
ARM: imx6q: move low-power code out of clock driver
ARM: imx: drop extern with function prototypes in common.h
ARM: imx: reset core along with enable/disable operation
ARM: imx: do not return from imx_cpu_die() call
ARM: imx_v6_v7_defconfig: Select CONFIG_PROVE_LOCKING
ARM: imx_v6_v7_defconfig: Enable LEDS_GPIO related options
ARM: mxs_defconfig: Turn off CONFIG_DEBUG_GPIO
ARM: imx: replace imx6q_restart() with mxc_restart()
ARM: mach-imx: mm-imx5: Retrieve iomuxc base address from dt
ARM: mach-imx: mm-imx5: Retrieve tzic base address from dt
...
The dma mask is not configured in the current code.
This was triggered by soc-dmaengine-pcm which allocate the dma
buffers with the imx-sdma as device.
This commit fix audio on imx31.
Signed-off-by: Philippe Rétornaz <philippe.retornaz@epfl.ch>
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Acked-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
register_platform_device_full() can setup the DMA mask provided the
appropriate member is set in struct platform_device_info. So lets
make that be the case. This avoids a direct reference to the DMA
masks by this driver.
While here, add the dma_set_mask_and_coherent() call which the DMA API
requires DMA-using drivers to call.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This code sequence:
if (!pdev->dev.dma_mask) {
pdev->dev.dma_mask = &pdev->dev.coherent_dma_mask;
pdev->dev.coherent_dma_mask = DMA_BIT_MASK(32);
}
bypasses the architectures check on the DMA mask. It can be replaced
with dma_coerce_mask_and_coherent(), avoiding the direct initialization
of this mask.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The DMA API requires drivers to call the appropriate dma_set_mask()
functions before doing any DMA mapping. Add this required call to
the AMBA PL330 driver.
Acked-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The DMA API requires drivers to call the appropriate dma_set_mask()
functions before doing any DMA mapping. Add this required call to
the AMBA PL08x driver.
Acked-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Driver core clears the driver data to NULL after device_release
or on probe failure, so just remove it from here.
Driver core change:
"device-core: Ensure drvdata = NULL when no driver is bound"
(sha1: 0998d06310)
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
drivers/dma/imx-dma.c:575:3: warning: format '%x' expects argument of type 'unsigned int', but argument 6 has type 'dma_addr_t'
drivers/dma/imx-dma.c:575:3: warning: format '%x' expects argument of type 'unsigned int', but argument 7 has type 'dma_addr_t'
drivers/dma/imx-dma.c:589:4: warning: format '%x' expects argument of type 'unsigned int', but argument 9 has type 'dma_addr_t'
drivers/dma/imx-dma.c:599:4: warning: format '%x' expects argument of type 'unsigned int', but argument 9 has type 'dma_addr_t'
drivers/dma/imx-dma.c:929:2: warning: format '%x' expects argument of type 'unsigned int', but argument 6 has type 'dma_addr_t'
drivers/dma/imx-dma.c:929:2: warning: format '%x' expects argument of type 'unsigned int', but argument 7 has type 'dma_addr_t'
drivers/dma/imx-dma.c:959:2: warning: format '%x' expects argument of type 'unsigned int', but argument 6 has type 'dma_addr_t'
drivers/dma/imx-dma.c:959:2: warning: format '%x' expects argument of type 'unsigned int', but argument 7 has type 'dma_addr_t'
We can't use the %pa format for these because this relates to phys_addr_t,
and dma_addr_t can be a different size. So, fix these by converting them
to %llx and casting the dma_addr_t to always be unsigned long long.
While we're here, also use %zu for size_t.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
edma header defines DMA_COMPLETE, this causes issues as commit adfedd9a32 move
DMA_SUCCESS to DMA_COMPLETE. edma should properly namespace its defines and
needs a future fix
Reported-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
the DMA_SUCCESS is a misnomer as dmaengine indicates the transfer is complete and
gives no guarantee of the transfer success. Hence we should use DMA_COMPLTE
instead of DMA_SUCCESS
Acked-by: Dan Williams <dan.j.williams@intel.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
When it fails to allocate a slot, edesc should be free'd before return;
Signed-off-by: Valentin Ilie <valentin.ilie@gmail.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
davinci-pcm uses 16 as the no.of periods. With this, in EDMA we have to
allocate atleast 17 slots: 1 slot for channel, and 16 slots the periods.
Due to this, the MAX_NR_SG limitation causes problems, set it to 20 to make
cyclic DMA work when davinci-pcm is converted to use DMA Engine. Also add
a comment clarifying this.
Signed-off-by: Joel Fernandes <joelf@ti.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
PaRAM set calculation is abstracted into its own function to
enable better reuse for other DMA cases such as cyclic. We adapt
the Slave SG case to use the new function.
This provides a much cleaner abstraction to the internals of the
PaRAM set. However, any PaRAM attributes that are not common to
all DMA types must be set separately such as setting of interrupts.
This function takes care of the most-common attributes.
Also added comments clarifying A-sync case calculations.
Signed-off-by: Joel Fernandes <joelf@ti.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
The earliest variants of the dma controller did not contain support for
controlling clocks.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Reviewed-by: Tomasz Figa <t.figa@samsung.com>
Acked-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Some pl330 have per channel irq and it is necessary
to allocate all of them. Loop over irq assigned for this
device to support these pl330 IPs.
For example this IP is available on Xilinx Zynq platform.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Tested-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
This patch proposes to remove the use of the IRQF_DISABLED flag
It's a NOOP since 2.6.35 and it will be removed one day.
Signed-off-by: Michael Opdenacker <michael.opdenacker@free-electrons.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
This patch proposes to remove the use of the IRQF_DISABLED flag
It's a NOOP since 2.6.35 and it will be removed one day.
Signed-off-by: Michael Opdenacker <michael.opdenacker@free-electrons.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Free memory allocated to edma_desc when failing to allocate slot.
Signed-off-by: Geyslan G. Bem <geyslan@gmail.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Commit 4981c4dc19 (DMA: shdma: switch DT mode to
use configuration data from a match table) added a new parameter to set_slave()
method but unfortunately got merged later than commit c4f6c41ba7
(dma: add driver for R-Car HPB-DMAC), so that the HPB-DMAC driver retained the
old prototype which caused this warning:
drivers/dma/sh/rcar-hpbdma.c:485: warning: initialization from incompatible
pointer type
The newly added parameter is used to override DMA slave address from 'struct
hpb_dmae_slave_config', so we have to add the 'slave_addr' field to 'struct
hpb_dmae_chan', conditionally assign it in set_slave() method, and return in
slave_addr() method.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Tested-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Commit c1c63a14f4 (DMA: shdma: switch to managed
resource allocation) got rid of shdma_free_irq() but unfortunately got merged
later than commit c4f6c41ba7 (dma: add driver for
R-Car HPB-DMAC), so that the HPB-DMAC driver retained the calls and got broken:
drivers/dma/sh/rcar-hpbdma.c: In function `hpb_dmae_alloc_chan_resources':
drivers/dma/sh/rcar-hpbdma.c:435: error: implicit declaration of function
`shdma_free_irq'
Fix this compilation error by removing the remaining shdma_free_irq() calls.
Reported-by: Simon Horman <horms@verge.net.au>
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Tested-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Allow the TI_EDMA to be built for ARCH_KEYSTONE which also supports
the EDMA IP.
Acked-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Powerpc is a mess of implicit includes by prom.h. Add the necessary
explicit includes to drivers in preparation of prom.h cleanup.
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Acked-by: Grant Likely <grant.likely@linaro.org>
This adds a new driver to support the s3c24xx dma using the dmaengine
and makes the old one in mach-s3c24xx obsolete in the long run.
Conceptually the s3c24xx-dma feels like a distant relative of the pl08x
with numerous virtual channels being mapped to a lot less physical ones.
The driver therefore borrows a lot from the amba-pl08x driver in this
regard. Functionality-wise the driver gains a memcpy ability in addition
to the slave_sg one.
The driver supports both the method for requesting the peripheral used
by SoCs before the S3C2443 and the different method for S3C2443 and later.
On earlier SoCs the hardware channels usable for specific peripherals is
constrainted while on later SoCs all channels can be used for any peripheral.
Tested on a s3c2416-based board, memcpy using the dmatest module and
slave_sg partially using the spi-s3c64xx driver.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This patch adds support for suspend/resume functionality to the cppi41
DMA driver. The steps necessary to make the system resume properly were
figured out by trial-and-error. The code as it stands now is the
minimum that has to be done to put the musb host system on an AM33xx
system into an operable state after resume.
Signed-off-by: Daniel Mack <zonque@gmail.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
dst_addr_width and src_addr_width should be a power of 2. Currently the
driver checks, that they both lie between 1 and 8 and that they are equal
to 1 or even. This however leaves an invalid value of 6 uncaught. Use an
explicit power of 2 check instead.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski+renesas@gmail.com>
[typo fix on changelog]
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Makes the code more readable and compact. No functional change.
Signed-off-by: Daniel Mack <zonque@gmail.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Instead of passing around struct plafform_device, use struct device and
save one level of dereferencing. This affects the following functions:
* cppi41_add_chans
* purge_descs
* deinit_cpii41
* init_descs
* init_cppi41
* cppi_glue_infos
It's just a cosmetic cleanup that makes the code more readable.
Signed-off-by: Daniel Mack <zonque@gmail.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
tegra_dma_prep_dma_cyclic is referenced only in this file.
Make it static.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Acked-by: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
We need to free the ld_active list head before jumping into the callback
routine. Otherwise the callback could run into issue_pending and change
our ld_active list head we just going to free. This will run the channel
list into an currupted and undefined state.
Signed-off-by: Michael Grzeschik <m.grzeschik@pengutronix.de>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
The TI_EDMA driver unconditionally calls functions provided by the
TI_PRIV_EDMA code, but it doesn't force that to be built-in. If that isn't
otherwise enabled somewhere, you can get build errors like:
linux-3.12.0-0.rc0.git1.1.fc21.armv7hl/drivers/dma/edma.c:593: undefined reference to `edma_free_slot'
drivers/built-in.o: In function `edma_terminate_all':
linux-3.12.0-0.rc0.git1.1.fc21.armv7hl/drivers/dma/edma.c:169: undefined reference to `edma_stop'
drivers/built-in.o: In function `edma_execute':
linux-3.12.0-0.rc0.git1.1.fc21.armv7hl/drivers/dma/edma.c:122: undefined reference to `edma_write_slot'
linux-3.12.0-0.rc0.git1.1.fc21.armv7hl/drivers/dma/edma.c:149: undefined reference to `edma_link'
linux-3.12.0-0.rc0.git1.1.fc21.armv7hl/drivers/dma/edma.c:152: undefined reference to `edma_start'
Make TI_EDMA select TI_PRIV_EDMA to avoid this.
Signed-off-by: Josh Boyer <jwboyer@fedoraproject.org>
Acked-by: Matt Porter <matt.porter@linaro.org>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Matt's @ti.com address bounces. Update the MODULE_AUTHOR information in
edma.c to his Linaro address.
Signed-off-by: Josh Boyer <jwboyer@fedoraproject.org>
Acked-by: Matt Porter <matt.porter@linaro.org>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
After the last architecture switched to generic hard irqs the config
options HAVE_GENERIC_HARDIRQS & GENERIC_HARDIRQS and the related code
for !CONFIG_GENERIC_HARDIRQS can be removed.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Pull slave-dmaengine updates from Vinod Koul:
"This pull brings:
- Andy's DW driver updates
- Guennadi's sh driver updates
- Pl08x driver fixes from Tomasz & Alban
- Improvements to mmp_pdma by Daniel
- TI EDMA fixes by Joel
- New drivers:
- Hisilicon k3dma driver
- Renesas rcar dma driver
- New API for publishing slave driver capablities
- Various fixes across the subsystem by Andy, Jingoo, Sachin etc..."
* 'for-linus' of git://git.infradead.org/users/vkoul/slave-dma: (94 commits)
dma: edma: Remove limits on number of slots
dma: edma: Leave linked to Null slot instead of DUMMY slot
dma: edma: Find missed events and issue them
ARM: edma: Add function to manually trigger an EDMA channel
dma: edma: Write out and handle MAX_NR_SG at a given time
dma: edma: Setup parameters to DMA MAX_NR_SG at a time
dmaengine: pl330: use dma_set_max_seg_size to set the sg limit
dmaengine: dma_slave_caps: remove sg entries
dma: replace devm_request_and_ioremap by devm_ioremap_resource
dma: ste_dma40: Fix potential null pointer dereference
dma: ste_dma40: Remove duplicate const
dma: imx-dma: Remove redundant NULL check
dma: dmagengine: fix function names in comments
dma: add driver for R-Car HPB-DMAC
dma: k3dma: use devm_ioremap_resource() instead of devm_request_and_ioremap()
dma: imx-sdma: Staticize sdma_driver_data structures
pch_dma: Add MODULE_DEVICE_TABLE
dmaengine: PL08x: Add cyclic transfer support
dmaengine: PL08x: Fix reading the byte count in cctl
dmaengine: PL08x: Add support for different maximum transfer size
...
Collection of random updates to the core and some end-driver fixups for
ioatdma and mv_xor:
* NUMA aware channel allocation
* Cleanup dmatest debugfs interface
* ioat: make raid-support Atom only
* mv_xor: big endian
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.14 (GNU/Linux)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=ldij
-----END PGP SIGNATURE-----
Merge tag 'dmaengine-3.12' of git://git.kernel.org/pub/scm/linux/kernel/git/djbw/dmaengine
Pull dmaengine update from Dan Williams:
"Collection of random updates to the core and some end-driver fixups
for ioatdma and mv_xor:
- NUMA aware channel allocation
- Cleanup dmatest debugfs interface
- ioat: make raid-support Atom only
- mv_xor: big endian
Aside from the top three commits these have all had some soak time in
-next. The top commit fixes a recent build breakage.
It has been a long while since my last pull request, hopefully it does
not show. Thanks to Vinod for keeping an eye on drivers/dma/ this
past year"
* tag 'dmaengine-3.12' of git://git.kernel.org/pub/scm/linux/kernel/git/djbw/dmaengine:
dmaengine: dma_sync_wait and dma_find_channel undefined
MAINTAINERS: update email for Dan Williams
dma: mv_xor: Fix incorrect error path
ioatdma: silence GCC warnings
dmaengine: make dma_channel_rebalance() NUMA aware
dmaengine: make dma_submit_error() return an error code
ioatdma: disable RAID on non-Atom platforms and reenable unaligned copies
mv_xor: support big endian systems using descriptor swap feature
mv_xor: use {readl, writel}_relaxed instead of __raw_{readl, writel}
dmatest: print message on debug level in case of no error
dmatest: remove IS_ERR_OR_NULL checks of debugfs calls
dmatest: make module parameters writable
These are changes that arrived a little late before the merge window,
or had dependencies on previous branches.
Highlights:
- ux500: misc. cleanup, fixup I2C devices
- exynos: DT updates for RTC; PM updates
- at91: DT updates for NAND; new platforms added to generic defconfig
- sunxi: DT updates: cubieboard2, pinctrl driver, gated clocks
- highbank: LPAE fixes, select necessary ARM errata
- omap: PM fixes and improvements; OMAP5 mailbox support
- omap: basic support for new DRA7xx SoCs
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=NIZZ
-----END PGP SIGNATURE-----
Merge tag 'late-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC late changes from Kevin Hilman:
"These are changes that arrived a little late before the merge window,
or had dependencies on previous branches.
Highlights:
- ux500: misc. cleanup, fixup I2C devices
- exynos: DT updates for RTC; PM updates
- at91: DT updates for NAND; new platforms added to generic defconfig
- sunxi: DT updates: cubieboard2, pinctrl driver, gated clocks
- highbank: LPAE fixes, select necessary ARM errata
- omap: PM fixes and improvements; OMAP5 mailbox support
- omap: basic support for new DRA7xx SoCs"
* tag 'late-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (60 commits)
ARM: dts: vexpress: Add CCI node to TC2 device-tree
ARM: EXYNOS: Skip C1 cpuidle state for exynos5440
ARM: EXYNOS: always enable PM domains support for EXYNOS4X12
ARM: highbank: clean-up some unused includes
ARM: sun7i: Enable the A20 clocks in the DTSI
ARM: sun6i: Enable clock support in the DTSI
ARM: sun5i: dt: Use the A10s gates in the DTSI
ARM: at91: at91_dt_defconfig: enable rm9200 support
ARM: dts: add ADC device tree node for exynos5420/5250
ARM: dts: Add RTC DT node to Exynos5420 SoC
ARM: dts: Update the "status" property of RTC DT node for Exynos5250 SoC
ARM: dts: Fix the RTC DT node name for Exynos5250
irqchip: mmp: avoid to include irqs head file
ARM: mmp: avoid to include head file in mach-mmp
irqchip: mmp: support irqchip
irqchip: move mmp irq driver
ARM: OMAP: AM33xx: clock: Add RNG clock data
ARM: OMAP: TI81XX: add always-on powerdomain for TI81XX
ARM: OMAP4: clock: Lock PLLs in the right sequence
ARM: OMAP: AM33XX: hwmod: Add hwmod data for debugSS
...
Return directly if memory allocation fails. There is no need
of dma_free_coherent().
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Cc: Saeed Bishara <saeed@marvell.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Pull vfs pile 1 from Al Viro:
"Unfortunately, this merge window it'll have a be a lot of small piles -
my fault, actually, for not keeping #for-next in anything that would
resemble a sane shape ;-/
This pile: assorted fixes (the first 3 are -stable fodder, IMO) and
cleanups + %pd/%pD formats (dentry/file pathname, up to 4 last
components) + several long-standing patches from various folks.
There definitely will be a lot more (starting with Miklos'
check_submount_and_drop() series)"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs: (26 commits)
direct-io: Handle O_(D)SYNC AIO
direct-io: Implement generic deferred AIO completions
add formats for dentry/file pathnames
kvm eventfd: switch to fdget
powerpc kvm: use fdget
switch fchmod() to fdget
switch epoll_ctl() to fdget
switch copy_module_from_fd() to fdget
git simplify nilfs check for busy subtree
ibmasmfs: don't bother passing superblock when not needed
don't pass superblock to hypfs_{mkdir,create*}
don't pass superblock to hypfs_diag_create_files
don't pass superblock to hypfs_vm_create_files()
oprofile: get rid of pointless forward declarations of struct super_block
oprofilefs_create_...() do not need superblock argument
oprofilefs_mkdir() doesn't need superblock argument
don't bother with passing superblock to oprofile_create_stats_files()
oprofile: don't bother with passing superblock to ->create_files()
don't bother passing sb to oprofile_create_files()
coh901318: don't open-code simple_read_from_buffer()
...
With this series, this check is no longer required and
we shouldn't need to reject drivers DMA'ing more than the
MAX number of slots.
Signed-off-by: Joel Fernandes <joelf@ti.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Vinod Koul