This driver was not unregistering its network interfaces on unbind.
Now it is.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Tested-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Reviewed-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
mscc_ocelot_probe() is already pretty large and hard to follow. So move
the code for parsing ports in a separate function.
This makes it easier for the next patch to just call
mscc_ocelot_release_ports from the error path of mscc_ocelot_init_ports.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Tested-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Reviewed-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
ocelot_init() allocates memory, resets the switch and polls for a status
register, things which can fail. Stop probing the driver in that case,
and propagate the error result.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Tested-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Reviewed-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Do not proceed probing if we couldn't allocate memory for the ports
array, just error out.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Tested-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Reviewed-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The VSC9953 Seville switch has 2 megabits of buffer split into 4360
words of 60 bytes each.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Tested-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Reviewed-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ocelot_port->ts_id is used to:
(a) populate skb->cb[0] for matching the TX timestamp in the PTP IRQ
with an skb.
(b) populate the REW_OP from the injection header of the ongoing skb.
Only then is ocelot_port->ts_id incremented.
This is a problem because, at least theoretically, another timestampable
skb might use the same ocelot_port->ts_id before that is incremented.
Normally all transmit calls are serialized by the netdev transmit
spinlock, but in this case, ocelot_port_add_txtstamp_skb() is also
called by DSA, which has started declaring the NETIF_F_LLTX feature
since commit 2b86cb8299 ("net: dsa: declare lockless TX feature for
slave ports"). So the logic of using and incrementing the timestamp id
should be atomic per port.
The solution is to use the global ocelot_port->ts_id only while
protected by the associated ocelot_port->ts_id_lock. That's where we
populate skb->cb[0]. Note that for ocelot, ocelot_port_add_txtstamp_skb
is called for the actual skb, but for felix, it is called for the skb's
clone. That is something which will also be changed in the future.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Tested-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Reviewed-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The TX-timestampable skb is added late to the ocelot_port->tx_skbs. It
is in a race with the TX timestamp IRQ, which checks that queue trying
to match the timestamp with the skb by the ts_id. The skb should be
added to the queue before the IRQ can fire.
Fixes: 4e3b0468e6 ("net: mscc: PTP Hardware Clock (PHC) support")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
struct ethtool_fecparam carries bitmasks not bit numbers.
We want to return 1 (NONE), not 0.
Fixes: 0d08709383 ("nfp: implement ethtool FEC mode settings")
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Reviewed-by: Simon Horman <simon.horman@netronome.com>
Reviewed-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In rx_request_irq(), it will just return what irq_set_affinity_hint()
returns. If it is failed, the napi and irq requested are not freed
properly. So add exits for failures to handle these.
Signed-off-by: Wei Li <liwei391@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Florian Fainelli says:
====================
net: phy: Unbind fixes
This patch series fixes a couple of issues with the unbinding of the PHY
drivers and then bringing down a network interface. The first is a NULL
pointer de-reference and the second was an incorrect warning being
triggered.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
When phy_is_started() was added to catch incorrect PHY states,
phy_stop() would not be qualified against PHY_DOWN. It is possible to
reach that state when the PHY driver has been unbound and the network
device is then brought down.
Fixes: 2b3e88ea65 ("net: phy: improve phy state checking")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
If we have unbound the PHY driver prior to calling phy_detach() (often
via phy_disconnect()) then we can cause a NULL pointer de-reference
accessing the driver owner member. The steps to reproduce are:
echo unimac-mdio-0:01 > /sys/class/net/eth0/phydev/driver/unbind
ip link set eth0 down
Fixes: cafe8df8b9 ("net: phy: Fix lack of reference count on PHY driver")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Tunnel offload info code uses ETHTOOL_MSG_TUNNEL_INFO_GET message type (cmd
field in genetlink header) for replies to tunnel info netlink request, i.e.
the same value as the request have. This is a problem because we are using
two separate enums for userspace to kernel and kernel to userspace message
types so that this ETHTOOL_MSG_TUNNEL_INFO_GET (28) collides with
ETHTOOL_MSG_CABLE_TEST_TDR_NTF which is what message type 28 means for
kernel to userspace messages.
As the tunnel info request reached mainline in 5.9 merge window, we should
still be able to fix the reply message type without breaking backward
compatibility.
Fixes: c7d759eb7b ("ethtool: add tunnel info interface")
Signed-off-by: Michal Kubecek <mkubecek@suse.cz>
Reviewed-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch sets skb->protocol before transmitting frames on the HDLC
device, so that a user listening on the HDLC device with an AF_PACKET
socket will see outgoing frames' sll_protocol field correctly set and
consistent with that of incoming frames.
1. Control frames in hdlc_cisco and hdlc_ppp
When these drivers send control frames, skb->protocol is not set.
This value should be set to htons(ETH_P_HDLC), because when receiving
control frames, their skb->protocol is set to htons(ETH_P_HDLC).
When receiving, hdlc_type_trans in hdlc.h is called, which then calls
cisco_type_trans or ppp_type_trans. The skb->protocol of control frames
is set to htons(ETH_P_HDLC) so that the control frames can be received
by hdlc_rcv in hdlc.c, which calls cisco_rx or ppp_rx to process the
control frames.
2. hdlc_fr
When this driver sends control frames, skb->protocol is set to internal
values used in this driver.
When this driver sends data frames (from upper stacked PVC devices),
skb->protocol is the same as that of the user data packet being sent on
the upper PVC device (for normal PVC devices), or is htons(ETH_P_802_3)
(for Ethernet-emulating PVC devices).
However, skb->protocol for both control frames and data frames should be
set to htons(ETH_P_HDLC), because when receiving, all frames received on
the HDLC device will have their skb->protocol set to htons(ETH_P_HDLC).
When receiving, hdlc_type_trans in hdlc.h is called, and because this
driver doesn't provide a type_trans function in struct hdlc_proto,
all frames will have their skb->protocol set to htons(ETH_P_HDLC).
The frames are then received by hdlc_rcv in hdlc.c, which calls fr_rx
to process the frames (control frames are consumed and data frames
are re-received on upper PVC devices).
Cc: Krzysztof Halasa <khc@pm.waw.pl>
Signed-off-by: Xie He <xie.he.0141@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This driver is a virtual driver stacked on top of Ethernet interfaces.
When this driver transmits data on the Ethernet device, the skb->protocol
setting is inconsistent with the Ethernet header prepended to the skb.
This causes a user listening on the Ethernet interface with an AF_PACKET
socket, to see different sll_protocol values for incoming and outgoing
frames, because incoming frames would have this value set by parsing the
Ethernet header.
This patch changes the skb->protocol value for outgoing Ethernet frames,
making it consistent with the Ethernet header prepended. This makes a
user listening on the Ethernet device with an AF_PACKET socket, to see
the same sll_protocol value for incoming and outgoing frames.
Cc: Martin Schiller <ms@dev.tdt.de>
Signed-off-by: Xie He <xie.he.0141@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix the memory leak in mps during module unload
path by freeing mps reference entries if the list
adpter->mps_ref is not already empty
Fixes: 28b3870578 ("cxgb4: Re-work the logic for mps refcounting")
Signed-off-by: Raju Rangoju <rajur@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For additional robustness in the face of Hyper-V errors or malicious
behavior, validate all values that originate from packets that Hyper-V
has sent to the guest in the host-to-guest ring buffer. Ensure that
invalid values cannot cause indexing off the end of an array, or
subvert an existing validation via integer overflow. Ensure that
outgoing packets do not have any leftover guest memory that has not
been zeroed out.
Signed-off-by: Andres Beltran <lkmlabelt@gmail.com>
Co-developed-by: Andrea Parri (Microsoft) <parri.andrea@gmail.com>
Signed-off-by: Andrea Parri (Microsoft) <parri.andrea@gmail.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: netdev@vger.kernel.org
Reviewed-by: Haiyang Zhang <haiyangz@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The KSZ9477 and KSZ8795 use the port_cnt field differently: For the
KSZ9477, it includes the CPU port(s), while for the KSZ8795, it doesn't.
It would be a good cleanup to make the handling of both drivers match,
but as a first step, fix the recently broken assignment of num_ports in
the KSZ8795 driver (which completely broke probing, as the CPU port
index was always failing the num_ports check).
Fixes: af199a1a9c ("net: dsa: microchip: set the correct number of ports")
Signed-off-by: Matthias Schiffer <matthias.schiffer@ew.tq-group.com>
Reviewed-by: Codrin Ciubotariu <codrin.ciubotariu@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds transport ports information for route lookup so that
IPsec can select Geneve tunnel traffic to do encryption. This is
needed for OVS/OVN IPsec with encrypted Geneve tunnels.
This can be tested by configuring a host-host VPN using an IKE
daemon and specifying port numbers. For example, for an
Openswan-type configuration, the following parameters should be
configured on both hosts and IPsec set up as-per normal:
$ cat /etc/ipsec.conf
conn in
...
left=$IP1
right=$IP2
...
leftprotoport=udp/6081
rightprotoport=udp
...
conn out
...
left=$IP1
right=$IP2
...
leftprotoport=udp
rightprotoport=udp/6081
...
The tunnel can then be setup using "ip" on both hosts (but
changing the relevant IP addresses):
$ ip link add tun type geneve id 1000 remote $IP2
$ ip addr add 192.168.0.1/24 dev tun
$ ip link set tun up
This can then be tested by pinging from $IP1:
$ ping 192.168.0.2
Without this patch the traffic is unencrypted on the wire.
Fixes: 2d07dc79fe ("geneve: add initial netdev driver for GENEVE tunnels")
Signed-off-by: Qiuyu Xiao <qiuyu.xiao.qyx@gmail.com>
Signed-off-by: Mark Gray <mark.d.gray@redhat.com>
Reviewed-by: Greg Rose <gvrose8192@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Alexei Starovoitov says:
====================
pull-request: bpf 2020-09-15
The following pull-request contains BPF updates for your *net* tree.
We've added 12 non-merge commits during the last 19 day(s) which contain
a total of 10 files changed, 47 insertions(+), 38 deletions(-).
The main changes are:
1) docs/bpf fixes, from Andrii.
2) ld_abs fix, from Daniel.
3) socket casting helpers fix, from Martin.
4) hash iterator fixes, from Yonghong.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
The bpf_skc_to_* type casting helpers are available to
BPF_PROG_TYPE_TRACING. The traced PTR_TO_BTF_ID may be NULL.
For example, the skb->sk may be NULL. Thus, these casting helpers
need to check "!sk" also and this patch fixes them.
Fixes: 0d4fad3e57 ("bpf: Add bpf_skc_to_udp6_sock() helper")
Fixes: 478cfbdf5f ("bpf: Add bpf_skc_to_{tcp, tcp_timewait, tcp_request}_sock() helpers")
Fixes: af7ec13833 ("bpf: Add bpf_skc_to_tcp6_sock() helper")
Signed-off-by: Martin KaFai Lau <kafai@fb.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Yonghong Song <yhs@fb.com>
Acked-by: Song Liu <songliubraving@fb.com>
Link: https://lore.kernel.org/bpf/20200915182959.241101-1-kafai@fb.com
Kfir reported that pmtu exceptions are not created properly for
deployments where multipath routes use the same device.
After some digging I see 2 compounding problems:
1. ip_route_output_key_hash_rcu is updating the flowi4_oif *after*
the route lookup. This is the second use case where this has
been a problem (the first is related to use of vti devices with
VRF). I can not find any reason for the oif to be changed after the
lookup; the code goes back to the start of git. It does not seem
logical so remove it.
2. fib_lookups for exceptions do not call fib_select_path to handle
multipath route selection based on the hash.
The end result is that the fib_lookup used to add the exception
always creates it based using the first leg of the route.
An example topology showing the problem:
| host1
+------+
| eth0 | .209
+------+
|
+------+
switch | br0 |
+------+
|
+---------+---------+
| host2 | host3
+------+ +------+
| eth0 | .250 | eth0 | 192.168.252.252
+------+ +------+
+-----+ +-----+
| vti | .2 | vti | 192.168.247.3
+-----+ +-----+
\ /
=================================
tunnels
192.168.247.1/24
for h in host1 host2 host3; do
ip netns add ${h}
ip -netns ${h} link set lo up
ip netns exec ${h} sysctl -wq net.ipv4.ip_forward=1
done
ip netns add switch
ip -netns switch li set lo up
ip -netns switch link add br0 type bridge stp 0
ip -netns switch link set br0 up
for n in 1 2 3; do
ip -netns switch link add eth-sw type veth peer name eth-h${n}
ip -netns switch li set eth-h${n} master br0 up
ip -netns switch li set eth-sw netns host${n} name eth0
done
ip -netns host1 addr add 192.168.252.209/24 dev eth0
ip -netns host1 link set dev eth0 up
ip -netns host1 route add 192.168.247.0/24 \
nexthop via 192.168.252.250 dev eth0 nexthop via 192.168.252.252 dev eth0
ip -netns host2 addr add 192.168.252.250/24 dev eth0
ip -netns host2 link set dev eth0 up
ip -netns host2 addr add 192.168.252.252/24 dev eth0
ip -netns host3 link set dev eth0 up
ip netns add tunnel
ip -netns tunnel li set lo up
ip -netns tunnel li add br0 type bridge
ip -netns tunnel li set br0 up
for n in $(seq 11 20); do
ip -netns tunnel addr add dev br0 192.168.247.${n}/24
done
for n in 2 3
do
ip -netns tunnel link add vti${n} type veth peer name eth${n}
ip -netns tunnel link set eth${n} mtu 1360 master br0 up
ip -netns tunnel link set vti${n} netns host${n} mtu 1360 up
ip -netns host${n} addr add dev vti${n} 192.168.247.${n}/24
done
ip -netns tunnel ro add default nexthop via 192.168.247.2 nexthop via 192.168.247.3
ip netns exec host1 ping -M do -s 1400 -c3 -I 192.168.252.209 192.168.247.11
ip netns exec host1 ping -M do -s 1400 -c3 -I 192.168.252.209 192.168.247.15
ip -netns host1 ro ls cache
Before this patch the cache always shows exceptions against the first
leg in the multipath route; 192.168.252.250 per this example. Since the
hash has an initial random seed, you may need to vary the final octet
more than what is listed. In my tests, using addresses between 11 and 19
usually found 1 that used both legs.
With this patch, the cache will have exceptions for both legs.
Fixes: 4895c771c7 ("ipv4: Add FIB nexthop exceptions")
Reported-by: Kfir Itzhak <mastertheknife@gmail.com>
Signed-off-by: David Ahern <dsahern@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix parameter description of tipc_link_bc_create()
Reported-by: Hulk Robot <hulkci@huawei.com>
Fixes: 16ad3f4022 ("tipc: introduce variable window congestion control")
Signed-off-by: Lu Wei <luwei32@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Update supporters for IBM Power SRIOV Virtual NIC Device Driver.
Thomas Falcon is moving on to other works. Dany Madden, Lijun Pan
and Sukadev Bhattiprolu are the current supporters.
Signed-off-by: Dany Madden <drt@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make path to bench_ringbufs.c just a text, not a special link.
Fixes: 97abb2b396 ("docs/bpf: Add BPF ring buffer design notes")
Reported-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Signed-off-by: Andrii Nakryiko <andriin@fb.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Link: https://lore.kernel.org/bpf/20200915005031.2748397-1-andriin@fb.com
For AF_XDP sockets, there was a discrepancy between the number of of
pinned pages and the size of the umem region.
The size of the umem region is used to validate the AF_XDP descriptor
addresses. The logic that pinned the pages covered by the region only
took whole pages into consideration, creating a mismatch between the
size and pinned pages. A user could then pass AF_XDP addresses outside
the range of pinned pages, but still within the size of the region,
crashing the kernel.
This change correctly calculates the number of pages to be
pinned. Further, the size check for the aligned mode is
simplified. Now the code simply checks if the size is divisible by the
chunk size.
Fixes: bbff2f321a ("xsk: new descriptor addressing scheme")
Reported-by: Ciara Loftus <ciara.loftus@intel.com>
Signed-off-by: Björn Töpel <bjorn.topel@intel.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Tested-by: Ciara Loftus <ciara.loftus@intel.com>
Acked-by: Song Liu <songliubraving@fb.com>
Link: https://lore.kernel.org/bpf/20200910075609.7904-1-bjorn.topel@gmail.com
In fl_set_erspan_opt(), all bits of erspan md was set 1, as this
function is also used to set opt MASK. However, when setting for
md->u.index for opt VALUE, the rest bits of the union md->u will
be left 1. It would cause to fail the match of the whole md when
version is 1 and only index is set.
This patch is to fix by initializing with 0 before setting erspan
md->u.
Reported-by: Shuang Li <shuali@redhat.com>
Fixes: 79b1011cb3 ("net: sched: allow flower to match erspan options")
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Xin Long says:
====================
net: improve vxlan option process in net_sched and lwtunnel
This patch is to do some mask when setting vxlan option in net_sched
and lwtunnel, so that only available bits can be set on vxlan md gbp.
This would help when users don't know exactly vxlan's gbp bits, and
avoid some mismatch because of some unavailable bits set by users.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
As we can see from vxlan_build/parse_gbp_hdr(), when processing metadata
on vxlan rx/tx path, only dont_learn/policy_applied/policy_id fields can
be set to or parse from the packet for vxlan gbp option.
So do the mask when set it in lwtunnel, as it does in act_tunnel_key and
cls_flower.
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As we can see from vxlan_build/parse_gbp_hdr(), when processing metadata
on vxlan rx/tx path, only dont_learn/policy_applied/policy_id fields can
be set to or parse from the packet for vxlan gbp option.
So we'd better do the mask when set it in act_tunnel_key and cls_flower.
Otherwise, when users don't know these bits, they may configure with a
value which can never be matched.
Reported-by: Shuang Li <shuali@redhat.com>
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In tipc_buf_append() it may change skb's frag_list, and it causes
problems when this skb is cloned. skb_unclone() doesn't really
make this skb's flag_list available to change.
Shuang Li has reported an use-after-free issue because of this
when creating quite a few macvlan dev over the same dev, where
the broadcast packets will be cloned and go up to the stack:
[ ] BUG: KASAN: use-after-free in pskb_expand_head+0x86d/0xea0
[ ] Call Trace:
[ ] dump_stack+0x7c/0xb0
[ ] print_address_description.constprop.7+0x1a/0x220
[ ] kasan_report.cold.10+0x37/0x7c
[ ] check_memory_region+0x183/0x1e0
[ ] pskb_expand_head+0x86d/0xea0
[ ] process_backlog+0x1df/0x660
[ ] net_rx_action+0x3b4/0xc90
[ ]
[ ] Allocated by task 1786:
[ ] kmem_cache_alloc+0xbf/0x220
[ ] skb_clone+0x10a/0x300
[ ] macvlan_broadcast+0x2f6/0x590 [macvlan]
[ ] macvlan_process_broadcast+0x37c/0x516 [macvlan]
[ ] process_one_work+0x66a/0x1060
[ ] worker_thread+0x87/0xb10
[ ]
[ ] Freed by task 3253:
[ ] kmem_cache_free+0x82/0x2a0
[ ] skb_release_data+0x2c3/0x6e0
[ ] kfree_skb+0x78/0x1d0
[ ] tipc_recvmsg+0x3be/0xa40 [tipc]
So fix it by using skb_unshare() instead, which would create a new
skb for the cloned frag and it'll be safe to change its frag_list.
The similar things were also done in sctp_make_reassembled_event(),
which is using skb_copy().
Reported-by: Shuang Li <shuali@redhat.com>
Fixes: 37e22164a8 ("tipc: rename and move message reassembly function")
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
tipc_group_add_to_tree() returns silently if `key` matches `nkey` of an
existing node, causing tipc_group_create_member() to leak memory. Let
tipc_group_add_to_tree() return an error in such a case, so that
tipc_group_create_member() can handle it properly.
Fixes: 75da2163db ("tipc: introduce communication groups")
Reported-and-tested-by: syzbot+f95d90c454864b3b5bc9@syzkaller.appspotmail.com
Cc: Hillf Danton <hdanton@sina.com>
Link: https://syzkaller.appspot.com/bug?id=048390604fe1b60df34150265479202f10e13aff
Signed-off-by: Peilin Ye <yepeilin.cs@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
flowi4_multipath_hash was added by the commit referenced below for
tunnels. Unfortunately, the patch did not initialize the new field
for several fast path lookups that do not initialize the entire flow
struct to 0. Fix those locations. Currently, flowi4_multipath_hash
is random garbage and affects the hash value computed by
fib_multipath_hash for multipath selection.
Fixes: 24ba14406c ("route: Add multipath_hash in flowi_common to make user-define hash")
Signed-off-by: David Ahern <dsahern@gmail.com>
Cc: wenxu <wenxu@ucloud.cn>
Signed-off-by: David S. Miller <davem@davemloft.net>
Hauke Mehrtens says:
====================
net: lantiq: Fix bugs in NAPI handling
This fixes multiple bugs in the NAPI handling.
Changes since:
v1:
- removed stable tag from "net: lantiq: use netif_tx_napi_add() for TX NAPI"
- Check the NAPI budged in "net: lantiq: Use napi_complete_done()"
- Add extra fix "net: lantiq: Disable IRQs only if NAPI gets scheduled"
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
The napi_schedule() call will only schedule the NAPI if it is not
already running. To make sure that we do not deactivate interrupts
without scheduling NAPI only deactivate the interrupts in case NAPI also
gets scheduled.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use napi_complete_done() and activate the interrupts when this function
returns true. This way the generic NAPI code can take care of activating
the interrupts.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
netif_tx_napi_add() should be used for NAPI in the TX direction instead
of the netif_napi_add() function.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
The call to netif_wake_queue() when the TX descriptors were freed was
missing. When there are no TX buffers available the TX queue will be
stopped, but it was not started again when they are available again,
this is fixed in this patch.
Fixes: fe1a56420c ("net: lantiq: Add Lantiq / Intel VRX200 Ethernet driver")
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some WinCE devices face connectivity issues via the NDIS interface. They
fail to register, resulting in -110 timeout errors and failures during the
probe procedure.
In this kind of WinCE devices, the Windows-side ndis driver needs quite
more time to be loaded and configured, so that the linux rndis host queries
to them fail to be responded correctly on time.
More specifically, when INIT is called on the WinCE side - no other
requests can be served by the Client and this results in a failed QUERY
afterwards.
The increase of the waiting time on the side of the linux rndis host in
the command-response loop leaves the INIT process to complete and respond
to a QUERY, which comes afterwards. The WinCE devices with this special
"feature" in their ndis driver are satisfied by this fix.
Signed-off-by: Olympia Giannou <olympia.giannou@leica-geosystems.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add missed suspend/resume callbacks to properly restore networking after
suspend/resume cycle.
Fixes: ed3525eda4 ("net: ethernet: ti: introduce cpsw switchdev based driver part 1 - dual-emac")
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Looks like u32p_replace_bits() should be used instead of
u32_replace_bits() which does not modifies the value but returns the
modified version.
Fixes: 2b9feef2b6 ("soc: qcom: ipa: filter and routing tables")
Signed-off-by: Vadym Kochan <vadym.kochan@plvision.eu>
Reviewed-by: Alex Elder <elder@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
When calling hinic_close in hinic_set_channels, all queues are
stopped after netif_tx_disable, but some queue may be rewaken in
free_tx_poll by mistake while drv is handling tx irq. If one queue
is rewaken core may call hinic_xmit_frame to send pkt after
netif_tx_disable within a short time which may results in accessing
memory that has been already freed in hinic_close. So we call
napi_disable before netif_tx_disable in hinic_close to fix this bug.
Fixes: 2eed5a8b61 ("hinic: add set_channels ethtool_ops support")
Signed-off-by: Luo bin <luobin9@huawei.com>
Reviewed-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
It's possible that the user specifies an interval that couldn't allow
any packet to be transmitted. This also avoids the issue of the
hrtimer handler starving the other threads because it's running too
often.
The solution is to reject interval sizes that according to the current
link speed wouldn't allow any packet to be transmitted.
Reported-by: syzbot+8267241609ae8c23b248@syzkaller.appspotmail.com
Fixes: 5a781ccbd1 ("tc: Add support for configuring the taprio scheduler")
Signed-off-by: Vinicius Costa Gomes <vinicius.gomes@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Tony Nguyen says:
====================
Intel Wired LAN Driver Updates 2020-09-09
This series contains updates to i40e and igc drivers.
Stefan Assmann changes num_vlans to u16 to fix may be used uninitialized
error and propagates error in i40_set_vsi_promisc() for i40e.
Vinicius corrects timestamping latency values for i225 devices and
accounts for TX timestamping delay for igc.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
This is the correct resolution for the conflict from
merging the "net" tree fix:
commit 26cb7085c8 ("enetc: Remove the mdio bus on PF probe bailout")
with the "net-next" new work:
commit 07095c025a ("net: enetc: Use DT protocol information to set up the ports")
that moved mdio bus allocation to an ealier stage of
the PF probing routine.
Fixes: a57066b1a0 ("Merge git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net")
Signed-off-by: Claudiu Manoil <claudiu.manoil@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove link to litmus tests that didn't make it to upstream. Fix ringbuf
benchmark link.
I wasn't able to test this with `make htmldocs`, unfortunately, because of
Sphinx dependencies. But bench_ringbufs.c path is certainly correct now.
Fixes: 97abb2b396 ("docs/bpf: Add BPF ring buffer design notes")
Reported-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Signed-off-by: Andrii Nakryiko <andriin@fb.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Link: https://lore.kernel.org/bpf/20200910225245.2896991-1-andriin@fb.com
Increase Rx ring size to address issue where hardware is reaching
the receive work limit.
Before:
[ 102.223342] de2104x 0000:17:00.0 eth0: rx work limit reached
[ 102.245695] de2104x 0000:17:00.0 eth0: rx work limit reached
[ 102.251387] de2104x 0000:17:00.0 eth0: rx work limit reached
[ 102.267444] de2104x 0000:17:00.0 eth0: rx work limit reached
Signed-off-by: Lucy Yan <lucyyan@google.com>
Reviewed-by: Moritz Fischer <mdf@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is no @validate argument.
CC: Johannes Berg <johannes.berg@intel.com>
Fixes: 3de6440354 ("netlink: re-add parse/validate functions in strict mode")
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Vladimir Oltean