In commit 13583b1659 ("PCI: refactor io size calculation code") Ram
had a thinko in the refactorization of the code: the end result used the
variable 'align' for the bus alignment, but the original code used
'min_align'.
Since then, another use of that 'align' variable got introduced by
commit c8adf9a3e8 ("PCI: pre-allocate additional resources to devices
only after successful allocation of essential resources.")
Fix both of those uses to use 'min_align' as they should.
Daniel Hellstrom <daniel@gaisler.com>
Acked-by: Ram Pai <linuxram@us.ibm.com>
Acked-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
without the reg property Ben's new code won't find the PCI & ISA
bridge and the devices won't get the DT-node attached.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Cc: davem@davemloft.net
Cc: monstr@monstr.eu
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Link: http://lkml.kernel.org/r/20110407121315.GA9204@linutronix.de
Signed-off-by: Ingo Molnar <mingo@elte.hu>
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6: (34 commits)
net: Add support for SMSC LAN9530, LAN9730 and LAN89530
mlx4_en: Restoring RX buffer pointer in case of failure
mlx4: Sensing link type at device initialization
ipv4: Fix "Set rt->rt_iif more sanely on output routes."
MAINTAINERS: add entry for Xen network backend
be2net: Fix suspend/resume operation
be2net: Rename some struct members for clarity
pppoe: drop PPPOX_ZOMBIEs in pppoe_flush_dev
dsa/mv88e6131: add support for mv88e6085 switch
ipv6: Enable RFS sk_rxhash tracking for ipv6 sockets (v2)
be2net: Fix a potential crash during shutdown.
bna: Fix for handling firmware heartbeat failure
can: mcp251x: Allow pass IRQ flags through platform data.
smsc911x: fix mac_lock acquision before calling smsc911x_mac_read
iwlwifi: accept EEPROM version 0x423 for iwl6000
rt2x00: fix cancelling uninitialized work
rtlwifi: Fix some warnings/bugs
p54usb: IDs for two new devices
wl12xx: fix potential buffer overflow in testmode nvs push
zd1211rw: reset rx idle timer from tasklet
...
If the request_fn ends up blocking, we could be re-entering
the plug flush. Since the list is protected by explicitly
not allowing schedule events, this isn't a terribly good idea.
Additionally, it can cause us to recurse. As request_fn called by
__blk_run_queue is allowed to 'schedule()' (after dropping the queue
lock of course), it is possible to get a recursive call:
schedule -> blk_flush_plug -> __blk_finish_plug -> flush_plug_list
-> __blk_run_queue -> request_fn -> schedule
We must make sure that the second schedule does not call into
blk_flush_plug again. So instead of leaving the list of requests on
blk_plug->list, move them to a separate list leaving blk_plug->list
empty.
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
The scheduler load balancer has specific code to deal with cases of
unbalanced system due to lots of unmovable tasks (for example because of
hard CPU affinity). In those situation, it excludes the busiest CPU that
has pinned tasks for load balance consideration such that it can perform
second 2nd load balance pass on the rest of the system.
This all works as designed if there is only one cgroup in the system.
However, when we have multiple cgroups, this logic has false positives and
triggers multiple load balance passes despite there are actually no pinned
tasks at all.
The reason it has false positives is that the all pinned logic is deep in
the lowest function of can_migrate_task() and is too low level:
load_balance_fair() iterates each task group and calls balance_tasks() to
migrate target load. Along the way, balance_tasks() will also set a
all_pinned variable. Given that task-groups are iterated, this all_pinned
variable is essentially the status of last group in the scanning process.
Task group can have number of reasons that no load being migrated, none
due to cpu affinity. However, this status bit is being propagated back up
to the higher level load_balance(), which incorrectly think that no tasks
were moved. It kick off the all pinned logic and start multiple passes
attempt to move load onto puller CPU.
To fix this, move the all_pinned aggregation up at the iterator level.
This ensures that the status is aggregated over all task-groups, not just
last one in the list.
Signed-off-by: Ken Chen <kenchen@google.com>
Cc: stable@kernel.org
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Link: http://lkml.kernel.org/r/BANLkTi=ernzNawaR5tJZEsV_QVnfxqXmsQ@mail.gmail.com
Signed-off-by: Ingo Molnar <mingo@elte.hu>
In function find_busiest_group(), the sched-domain avg_load isn't
calculated at all if there is a group imbalance within the domain. This
will cause erroneous imbalance calculation.
The reason is that calculate_imbalance() sees sds->avg_load = 0 and it
will dump entire sds->max_load into imbalance variable, which is used
later on to migrate entire load from busiest CPU to the puller CPU.
This has two really bad effect:
1. stampede of task migration, and they won't be able to break out
of the bad state because of positive feedback loop: large load
delta -> heavier load migration -> larger imbalance and the cycle
goes on.
2. severe imbalance in CPU queue depth. This causes really long
scheduling latency blip which affects badly on application that
has tight latency requirement.
The fix is to have kernel calculate domain avg_load in both cases. This
will ensure that imbalance calculation is always sensible and the target
is usually half way between busiest and puller CPU.
Signed-off-by: Ken Chen <kenchen@google.com>
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: <stable@kernel.org>
Link: http://lkml.kernel.org/r/20110408002322.3A0D812217F@elm.corp.google.com
Signed-off-by: Ingo Molnar <mingo@elte.hu>
There is a bug in perf_event_enable_on_exec() when cgroup events are
active on a CPU: the cgroup events may be scheduled twice causing event
state corruptions which eventually may lead to kernel panics.
The reason is that the function needs to first schedule out the cgroup
events, just like for the per-thread events. The cgroup event are
scheduled back in automatically from the perf_event_context_sched_in()
function.
The patch also adds a WARN_ON_ONCE() is perf_cgroup_switch() to catch any
bogus state.
Signed-off-by: Stephane Eranian <eranian@google.com>
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Link: http://lkml.kernel.org/r/20110406005454.GA1062@quad
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Commit 000061245a, "dt/powerpc:
Eliminate users of of_platform_{,un}register_driver" forgot to convert
the type of structure passed into platform_device_register() when it
was converted from of_platform_device_register. Fix it.
Signed-off-by: Ira W. Snyder <iws@ovro.caltech.edu>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
* 'nouveau/drm-nouveau-fixes' of /ssd/git/drm-nouveau-next:
drm/nvc0: improve vm flush function
drm/nv50-nvc0: remove some code that doesn't belong here
drm/nv50: use "nv86" tlb flush method on everything except 0x50/0xac
drm/nouveau: quirk for XFX GT-240X-YA
drm/nv50-nvc0: work around an evo channel hang that some people see
drm/nouveau: implement init table opcode 0x5c
drm/nouveau: fix oops on unload with disabled LVDS panel
nv30: Fix parsing of perf table
drm/nouveau: correct memtiming table parsing for nv4x
Revert commit 6de9843dab, since it
caused a data corruption regression with BitTorrent downloads. Thanks
to Damien for discovering and bisecting to find the problem commit.
https://bugzilla.kernel.org/show_bug.cgi?id=32972
Reported-by: Damien Grassart <damien@grassart.com>
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
We can create 4402345721856 byte file with indirect block mapping.
However, if we grow an indirect-block file to the size with ftruncate(),
we can see an ext4 warning. The following patch fixes this problem.
How to reproduce:
# dd if=/dev/zero of=/mnt/mp1/hoge bs=1 count=0 seek=4402345721856
0+0 records in
0+0 records out
0 bytes (0 B) copied, 0.000221428 s, 0.0 kB/s
# tail -n 1 /var/log/messages
Nov 25 15:10:27 test kernel: EXT4-fs warning (device sda8): ext4_block_to_path:345: block 1074791436 > max in inode 12
Signed-off-by: Kazuya Mio <k-mio@sx.jp.nec.com>
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
ext4_journal_start_sb() should not prevent an active handle from being
started due to s_frozen. Otherwise, deadlock is easy to happen, below
is a situation.
================================================
freeze | truncate
================================================
| ext4_ext_truncate()
freeze_super() | starts a handle
sets s_frozen |
| ext4_ext_truncate()
| holds i_data_sem
ext4_freeze() |
waits for updates |
| ext4_free_blocks()
| calls dquot_free_block()
|
| dquot_free_blocks()
| calls ext4_dirty_inode()
|
| ext4_dirty_inode()
| trys to start an active
| handle
|
| block due to s_frozen
================================================
Signed-off-by: Yongqiang Yang <xiaoqiangnk@gmail.com>
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
Reported-by: Amir Goldstein <amir73il@users.sf.net>
Reviewed-by: Jan Kara <jack@suse.cz>
Reviewed-by: Andreas Dilger <adilger@dilger.ca>
ext4 has taken the stance that, in the absence of a journal,
when an fsync/fdatasync of an inode is done, the parent
directory should be sync'ed if this inode entry is new.
ext4_sync_parent(), which implements this, does indeed sync
the dirent pages for parent directories, but it does not
sync the directory *inode*. This patch fixes this.
Also now return error status from ext4_sync_parent().
I tested this using a power fail test, which panics a
machine running a file server getting requests from a
client. Without this patch, on about every other test run,
the server is missing many, many files that had been synced.
With this patch, on > 6 runs, I see zero files being lost.
Google-Bug-Id: 4179519
Signed-off-by: Curt Wohlgemuth <curtw@google.com>
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
This patch adds support for SMSC's LAN9530, LAN9730 and LAN89530 USB
ethernet controllers to the existing smsc95xx driver by adding
their new USB VID/PID pairs.
Signed-off-by: Steve Glendinning <steve.glendinning@smsc.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The patch below removes an unused config variable found by using a kernel
cleanup script.
Signed-off-by: Justin P. Mattock <justinmattock@gmail.com>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Acked-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
VFP registers d16-d31 are callee saved registers and must be preserved
during function calls, including fork(). The VFP configuration should
also be preserved. The patch copies the full VFP state to the child
process.
Reported-by: Paul Wright <paul.wright@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This patch adds THREAD_NOTIFY_COPY for calling registered handlers
during the copy_thread() function call. It also changes the VFP handler
to use a switch statement rather than if..else and ignore this event.
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The HIGHPTE config option depends on !OUTER_CACHE. However, there is no
set_pte_ext() function that does outer cache maintenance by physical
address, hence no need for such restriction.
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Commit a737823d ("ARM: perf: ensure overflows aren't missed due to IRQ
latency") changed the way that event deltas are calculated on overflow
so that we don't miss events when the new count value overtakes the
previous one.
Unfortunately, we forget to count the event that passes through zero so
we end up being off by 1. This patch adds on the correction.
Reported-by: Chris Moore <moore@free.fr>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The DBGVCR, used for configuring vector catch debug events, is UNKNOWN
out of reset on ARMv7. When enabling monitor mode, this must be zeroed
to avoid UNPREDICTABLE behaviour.
This patch adds the zeroing code to the debug reset path.
Cc: stable <stable@kernel.org>
Reported-by: Stepan Moskovchenko <stepanm@codeaurora.org>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound-2.6:
ALSA: hda - Don't query connections for widgets have no connections
ALSA: HDA: Fix single internal mic on ALC275 (Sony Vaio VPCSB1C5E)
ALSA: hda - HDMI: Fix MCP7x audio infoframe checksums
ALSA: usb-audio: define another USB ID for a buggy USB MIDI cable
ALSA: HDA: Fix dock mic for Lenovo X220-tablet
ASoC: format_register_str: Don't clip register values
ASoC: PXA: Fix oops in __pxa2xx_pcm_prepare
ASoC: zylonite: set .codec_dai_name in initializer
* git://git.infradead.org/mtd-2.6:
mtd: atmel_nand: use CPU I/O when buffer is in vmalloc(ed) region
mtd: atmel_nand: modify test case for using DMA operations
mtd: atmel_nand: fix support for CPUs that do not support DMA access
mtd: atmel_nand: trivial: change DMA usage information trace
mtd: mtdswap: fix printk format warning
Switch some errors to debug output. These are generally harmless
and tend to confuse users.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
This is necessary even with PCI(e) GART, and it makes writeback work even with
AGP on my PowerBook. Might still be unreliable with older revisions of UniNorth
and other AGP bridges though.
Signed-off-by: Michel Dänzer <daenzer@vmware.com>
Reviewed-by: Alex Deucher <alex.deucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
This has always used a big hammer, but that hammer is probably
too big, I'm also not sure its necessary but at least this
should be safe.
Should fix: https://bugzilla.kernel.org/show_bug.cgi?id=23592
Signed-off-by: Dave Airlie <airlied@redhat.com>
* 'bugfixes' of git://git.linux-nfs.org/projects/trondmy/nfs-2.6:
NFS: Change initial mount authflavor only when server returns NFS4ERR_WRONGSEC
NFS: Fix a signed vs. unsigned secinfo bug
Revert "net/sunrpc: Use static const char arrays"
Apparently it is ok to submit a read to an IDE device with the same target page
for different offsets. This is what Windows does under qemu. The problem is
under DIO we expect them to be different buffers for checksumming reasons, and
so this sort of thing will result in checksum errors, when in reality the file
is fine. So when reading, check to make sure that all iov bases are different,
and if they aren't fall back to buffered mode, since that will work out right.
Thanks,
Signed-off-by: Josef Bacik <josef@redhat.com>
In btrfs_get_block_direct we call btrfs_get_extent to lookup the extent for the
range that we are looking for. If we don't find an extent, btrfs_get_extent
will insert a extent_map for that area and mark it as a hole. So it does the
job of allocating a new extent map and inserting it into the io tree. But if
we're creating a new extent we free it up and redo all of that work. So instead
pass the em to btrfs_new_extent_direct(), and if it will work just allocate the
disk space and set it up properly and bypass the freeing/allocating of a new
extent map and the expensive operation of inserting the thing into the io_tree.
Thanks,
Signed-off-by: Josef Bacik <josef@redhat.com>
When looking at our DIO performance Chris said that for small IO's doing the
async submit stuff tends to be more overhead than it's worth. With this on top
of my other fixes I get about a 17-20% speedup doing a sequential dd with 4k
IO's. Basically if we don't have to split the bio for the map length it's small
enough to be directly submitted, otherwise go back to the async submit. Thanks,
Signed-off-by: Josef Bacik <josef@redhat.com>
We have been unconditionally allocating a new bio and re-adding all pages from
our original bio to the new bio. This is needed if our original bio is larger
than our stripe size, but if it is smaller than the stripe size then there is no
need to do this. So check the map length and if we are under that then go ahead
and submit the original bio. Thanks,
Signed-off-by: Josef Bacik <josef@redhat.com>
In the DIO code we often don't update the i_disk_size because the i_size isn't
updated until after the DIO is completed, so basically we are allocating a path,
doing a search, and updating the inode item for no reason since nothing changed.
btrfs_ordered_update_i_size will return 1 if it didn't update i_disk_size, so
only run btrfs_update_inode if btrfs_ordered_update_i_size returns 0. Thanks,
Signed-off-by: Josef Bacik <josef@redhat.com>
Instead of calling kmap_atomic for every thing we set in the inode item, map the
entire inode item at the start and unmap it at the end. This makes a sequential
dd of 400mb O_DIRECT something like 1% faster. Thanks,
Signed-off-by: Josef Bacik <josef@redhat.com>
I saw a lockup where we kept getting into this start transaction->commit
transaction loop because of enospce. The fact is if we fail to make our
reservation, we've tried _everything_ several times, so we only need to try and
commit the transaction once, and if that doesn't work then we really are out of
space and need to just exit. Thanks,
Signed-off-by: Josef Bacik <josef@redhat.com>
Currently we don't handle running out of space in the cache, so to fix this we
keep track of how far in the cache we are. Then we only dirty the pages if we
successfully modify all of them, otherwise if we have an error or run out of
space we can just drop them and not worry about the vm writing them out.
Thanks,
Tested-by Johannes Hirte <johannes.hirte@fem.tu-ilmenau.de>
Signed-off-by: Josef Bacik <josef@redhat.com>
Fix this:
util/cgroup.c: In function ‘open_cgroup’:
util/cgroup.c:16:16: error: ‘saved_ptr’ may be used uninitialized in this function
util/cgroup.c:16:16: note: ‘saved_ptr’ was declared here
Apparently newer GCC (4.6) can figure out that this variable is properly
initialized - but some versions of GCC (such as 4.5.2) need help.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Cc: Arnaldo Carvalho de Melo <acme@infradead.org>
LKML-Reference: <new-submission>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
* 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jack/linux-fs-2.6:
quota: Don't write quota info in dquot_commit()
ext3: Fix writepage credits computation for ordered mode
Add proper blk_start_plug/blk_finish_plug pairs for the two places where
we issue buffer I/O, and remove the blk_flush_plug in xfs_buf_lock and
xfs_buf_iowait, given that context switches already flush the per-process
plugging lists.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Alex Elder <aelder@sgi.com>
For a CONFIG_XFS_DEBUG=n build gcc complains about statements with no
effect in xfs_debug:
fs/xfs/quota/xfs_qm_syscalls.c: In function 'xfs_qm_scall_trunc_qfiles':
fs/xfs/quota/xfs_qm_syscalls.c:291:3: warning: statement with no effect
The reason for that is that the various new xfs message functions have a
return value which is never used, and in case of the non-debug build
xfs_debug the macro evaluates to a plain 0 which produces the above
warnings. This can be fixed by turning xfs_debug into an inline function
instead of a macro, but in addition to that I've also changed all the
message helpers to return void as we never use their return values.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Dave Chinner <dchinner@redhat.com>
Signed-off-by: Alex Elder <aelder@sgi.com>
GCC 4.6 now warnings about variables set but not used. Fix the trivially
fixable warnings of this sort.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Alex Elder <aelder@sgi.com>
If not done, second attempt to open the RX ring would cause memory corruption.
Signed-off-by: Yevgeny Petrilin <yevgenyp@mellanox.co.il>
Signed-off-by: David S. Miller <davem@davemloft.net>
When bringing the port up, performing a SENSE_PORT command
To try and check to which physical link type (IB or Ethernet) the physical
port is connected.
In case there is no valid link partner, the port will come up as its
supported default.
Signed-off-by: Yevgeny Petrilin <yevgenyp@mellanox.co.il>
Signed-off-by: David S. Miller <davem@davemloft.net>
On the Power platform, the log tail debug checks fire excessively
causing the system to panic early in testing. The debug checks are
known to be racy, though on x86_64 there is no evidence that they
trigger at all.
We want to keep the checks active on debug systems to alert us to
problems with log space accounting, but we need to reduce the impact
of a racy check on testing on the Power platform.
As a result, convert the ASSERT conditions to warnings, and
allow them to fire only once per filesystem mount. This will prevent
false positives from interfering with testing, whilst still
providing us with the indication that they may be a problem with log
space accounting should that occur.
Signed-off-by: Dave Chinner <dchinner@redhat.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Alex Elder <aelder@sgi.com>
A fuzzed filesystem crashed a kernel when freeing an extent with a
block number beyond the end of the filesystem. Convert all the debug
asserts in xfs_free_extent() to active checks so that we catch bad
extents and return that the filesytsem is corrupted rather than
crashing.
Signed-off-by: Dave Chinner <dchinner@redhat.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Alex Elder <aelder@sgi.com>
Linus Torvalds