Both devices are using the same iio_chan_spec to define which settings
are exported with sysfs. Both are properly configured to set/get
sampling frequency for pressure and temperature. They also properly
export available sampling frequencies. The only missing thing is
sampling_frequency sysfs file, which allows to set/get this property
from userspace.
Add sampling frequency to iio channel info mask, so sampling_frequency
file is properly exported using sysfs.
Signed-off-by: Marcin Niestroj <m.niestroj@grinn-global.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Datasheet of each device (lps331ap, lps25h, lps001wp, lps22hb) says that
the pressure and temperature data is a 2's complement.
I'm sending this the slow way, as negative pressures on these are pretty
unusual and the nature of the fixing of multiple device introduction patches
will make it hard to apply to older kernels - Jonathan.
Fixes: 217494e5b7 ("iio:pressure: Add STMicroelectronics pressures driver")
Fixes: 2f5effcbd0 ("iio: pressure-core: st: Expand and rename LPS331AP's channel descriptor")
Fixes: 7885a8ce68 ("iio: pressure: st: Add support for new LPS001WP pressure sensor")
Fixes: e039e2f5b4 ("iio:st_pressure:initial lps22hb sensor support")
Signed-off-by: Marcin Niestroj <m.niestroj@grinn-global.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
msleep(1~20) may not do what the caller intends, and will often sleep longer.
(~20 ms actual sleep for any value given in the 1~20ms range)
This is not the desired behaviour for many cases like device resume time,
device suspend time, device enable time, data reading time, etc.
Thus, change msleep to usleep_range for precise wakeups.
Signed-off-by: Aniroop Mathur <a.mathur@samsung.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Compatible strings are not available on ACPI based systems. This patch adds
support to use DSDT information read from platform BIOS instead for probing
st pressure sensors.
Signed-off-by: Shrirang Bagul <shrirang.bagul@canonical.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
We have #defines for all the individual sensor registers and
value/mask pairs #defined at the top of the file and used at
exactly one spot.
This is usually good if the #defines give a meaning to the
opaque magic numbers.
However in this case, the semantic meaning is inherent in the
name of the C99-addressable fields, and that means duplication
of information, and only makes the code hard to maintain since
you every time have to add a new #define AND update the site
where it is to be used.
Get rid of the #defines and just open code the values into the
appropriate struct elements. Make sure to explicitly address
the .hz and .value fields in the st_sensor_odr_avl struct
so that the meaning of all values is clear.
This patch is purely syntactic should have no semantic effect.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Fair number of outreachy related patches in here. Some of these may well
have already been picked up by Greg but git will sort that out for us.
Also some good staging cleanup work from other sources. Thanks Brian and Lars
in particular for this.
New device support
* ACCES 104-quad-8
- New driver for this 8 channel encoder input board. Lots of new ABI with
this one.
* AD7766
- New driver supporting AD7766, AD7766-1, AD7766-2, AD7767, AD7767-1 and
AD7767-2 24 bit ADCs.
* dmard 10
- New driver for this 3 axis accelerometer.
* Honeywell ABP pressure sensors.
- New driver covering 56 parts in this series (too many to list here!)
* HTS221
- New driver to support this relative humidiy and temperature device.
* LMP91000
- New driver for this potentiostat (form of chemical sensor). Nice example
of use of the buffered consumer interfaces and the use of a consumer
provided trigger.
* MiraMEMS DA311
- New driver for this 3 axis accelerometer.
* MiraMEMS DA280
- New driver for this 3 axis accelerometer. Follow up caught up with
vendor prefixes for these.
Staging graduations
* isl29018 light sensor
- Fixes and cleanups listed below (thanks for your hard work on this Brian!)
* sca3000
- Fixes and cleanups listed below. This was one of the small set of drivers
that went into staging when IIO was first added. Turns out it had a few
bugs and needed to be brought into the modern era! Not clear if I am
the only person who actually has one of these still wired to a board.
New features (Core)
- Add an iio_trigger_validate_own_device helper which relies on the device
and trigger having the same parent. Convenient to have this for some
of the more complex trigger / device interactions. Was hand rolled in
a few drivers already so good to bring it into the core.
- Add an iio_read_channel_offset in kernel access helper (similar to
the existing one for scale).
- IIO_ATTR_{RO, WO, RW} and IIO_DEVICE_ATTR_{RO, WO, RW} macros. These
lead some rather contrived function naming, but there is no denying they
do reduced boilerplate. I'm going to resist their introduction in
drivers 'unless' they form part of a larger set of cleanups.
- Counter channel type and index type.
New features (Drivers)
* hdc100x
- Triggered buffer support.
* mcp4725
- Device tree bindings and support.
- Voltage reference selection.
* ti-adc0832
- Triggered buffer support.
* ti-adc161s626
- Add regulator support allowing _scale and _offset values to be established
and exported.
New features (Tools)
* iio_generic_buffer
- -A option to force enable all channels rather than faulting if some are
already enabled (like -a does). Followup patches tidied this support up.
Cleanups (Core)
- Use kmalloc_array in iio_scan_mask_set.
- Take event_attrs field of iio_info structure constant
- Staging todo list updates. Most of it was long done.
- MAINTAINERS had a wrong directory listing.
Cleanups (Drivers)
* Missing i2c trivial devices entries.
* ad5592r
- Fix an endian type related sparse warnings.
* ad7150
- Constify the event attribute_group structures.
* ad7152
- Add some blank lines to improve readability.
- Sampling frequency control via chan-info element rather than hand rolled
attributes.
- add a new lock to avoid use of mlock for non state change related locking.
* ad7280
- Constify atrribute_group structure (second patch covers the event ones)
* ad7606 (Lars is driving most of the cleanup on this with some additions from
Eva)
- Fix improper setting of oversampling pins. This has been broken a very
long time in this staging driver, so not going to push this back to stable.
- Implement oversampling configuration via the chan_info mask element.
- Remove an unused int_vref_mv field.
- Remove a reundant name field from ad7606_chip_info.
- Remove default device configuration from platform_data in favour of
whatever the power on defaults are.
- Remove out of band error reporting in the kernel log as not providing
much information.
- Fix oversampling ratio by having 1 be the value for no oversampling.
- Avoid allocating buffer for each data capture.
- Factor out common code between periodic and one-shot capture.
- Move set_drvdat into common code.
- Let the common probe function return int rather than jumping through
an ERR_PTR.
- Pass struct device * into common remove to simplify code.
- Always run trigger handler only once per event (no one can remember why
it was being possibly done twice).
- Move over to the GPIO descriptor API to shorten and clarify code.
- Move the buffer code into the main file as it's not optional and is
now rather short in this driver.
- Fix the naming of the supply regulator.
- Rework regulator handling to handle errors including deferred probing.
- Tidy up a ptr_err or 0 return.
* ad7746
- Sampling frequency control via info_mask element rather than hand rolled
* ad7758
- Sampling frequency control via info_mask element rather than hand rolled
attributes.
* ad7816
- Constify the event attribute_group structure.
* adt7316
- Constify the event attribute group structures.
* ak8974
- Cleanup some sparse warnings about endian types.
* ak8975
- Cleanup some sparse warnings about endian types.
* bmi160
- Spare endian warning cleanups.
* isl29018 (towards staging graduation)
- Remove unusedvariables and defines.
- Improve consistency of error handling.
- Signed / unsigned comparison fixes.
- Use the IIO_DEVICE_ATTR_{RO, RW} macros
- Fix a race in in_illuminance_scale_available_show.
- Cleanup exit points of _read_raw
- Sanity check if in suspended state during a write_raw call as was already
done for read_raw.
- Document device tree bidnings.
- Document infrared supression controls.
- Add some newlines to improve readability and drop one that shouldn't be
there.
- Fix a poorly named functions name.
- Fix multiline coment syntax.
- Tidy up a pair or return statements by unifying them.
- Rename description in Kconfig for consistency with similar drivers.
* lidar
- cleanup power management by dropping unnecessary call.
* ltr501
- Use the claim_direct_mode helpers. Fix a race condition along the way.
* max1027
- Fix a dubious x | !y sparse warning.
- Use the new iio_trigger_validate_own_device helper.
* max440000
- Clean up some sparse warnings about endian types.
* mcp4725
- Use the regulator framework to establish the reference voltage rather than
getting it from platform data.
- Tidy up a comment typo.
- Fix a wrong PTR_ERR query (wrong regulator).
* mma7660
- Take a mma7660_nscale static.
* mma8452
- Use the new iio_trigger_validate_own_device helper.
- Use claim_direct_mode helpers - fix a race condition along the way.
* mpl3115
- Use claim_direct_mode helpers - fix a race condition along the way.
* ms65611
- Tidy up regulator error handling and clean out a static warning in the mix.
* sca3000
- Avoid a potential unitialized variable if a hardware read returns a value
that isn't actually supported (mostly warning supression).
- Fix a use before setting of the indio_dev->buffer pointer. Broken for
a very long time so not going to rush this into stable.
- Merge buffer file with core file. We used to always split these.
Sometimes it's just not worth the hassle. In this case the device's main
feature is it's hardware fifos so unlikely anyone would want to run it
without.
- Drop the sca3000_register_ring_funcs function as it's a pointless wrapper
once we have only one file.
- Fix cleaning of flag + setting of size of scan. Without this you can't
start the buffer twice and expect sensible (or any) results. Again,
broken for a long time so not heading for stable.
- Drop the custom watershed setting ABI - for now we'll just support one
value.
- Move to a hybrid hard / soft buffer design (how we've been doing it
for similar devices for a while now!)
- Cleanup some unusued variables.
- Use a fake channel to support core handling of freefall event registration.
- Cleanup the register defines.
- Fix an off by one error in axis due to IIO_NO_MOD taking up the 0 value.
Been broken since first admission of IIO to the staging tree.
- Add readback of the 3db low pass filter frequency and later writing
allowing droppign of custom measurement mode attributes as they can
be represented by the filter choices that is their main characteristic.
- Drop non standard revision attr and replace with dev_info on probe.
- Avoid a race in probe.
- Various formatting fixes.
- Kernel-docify docs that were very nearly in the write format.
* tsl2583
- Constify attribute_group structure.
* zpa2326
- Drop a redundant DEBUG ifdef.
Cleanups (Tools)
* iio_generic_buffer
- Fix the ? arguement. Previously it sort of worked as you got the help
message as a result of it not recognising the arguement.
-----BEGIN PGP SIGNATURE-----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=ZRUt
-----END PGP SIGNATURE-----
Merge tag 'iio-for-4.10a' of git://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio into staging-next
Jonathan writes:
First round of IIO new device support, features and cleanups for the 4.10 cycle.
Fair number of outreachy related patches in here. Some of these may well
have already been picked up by Greg but git will sort that out for us.
Also some good staging cleanup work from other sources. Thanks Brian and Lars
in particular for this.
New device support
* ACCES 104-quad-8
- New driver for this 8 channel encoder input board. Lots of new ABI with
this one.
* AD7766
- New driver supporting AD7766, AD7766-1, AD7766-2, AD7767, AD7767-1 and
AD7767-2 24 bit ADCs.
* dmard 10
- New driver for this 3 axis accelerometer.
* Honeywell ABP pressure sensors.
- New driver covering 56 parts in this series (too many to list here!)
* HTS221
- New driver to support this relative humidiy and temperature device.
* LMP91000
- New driver for this potentiostat (form of chemical sensor). Nice example
of use of the buffered consumer interfaces and the use of a consumer
provided trigger.
* MiraMEMS DA311
- New driver for this 3 axis accelerometer.
* MiraMEMS DA280
- New driver for this 3 axis accelerometer. Follow up caught up with
vendor prefixes for these.
Staging graduations
* isl29018 light sensor
- Fixes and cleanups listed below (thanks for your hard work on this Brian!)
* sca3000
- Fixes and cleanups listed below. This was one of the small set of drivers
that went into staging when IIO was first added. Turns out it had a few
bugs and needed to be brought into the modern era! Not clear if I am
the only person who actually has one of these still wired to a board.
New features (Core)
- Add an iio_trigger_validate_own_device helper which relies on the device
and trigger having the same parent. Convenient to have this for some
of the more complex trigger / device interactions. Was hand rolled in
a few drivers already so good to bring it into the core.
- Add an iio_read_channel_offset in kernel access helper (similar to
the existing one for scale).
- IIO_ATTR_{RO, WO, RW} and IIO_DEVICE_ATTR_{RO, WO, RW} macros. These
lead some rather contrived function naming, but there is no denying they
do reduced boilerplate. I'm going to resist their introduction in
drivers 'unless' they form part of a larger set of cleanups.
- Counter channel type and index type.
New features (Drivers)
* hdc100x
- Triggered buffer support.
* mcp4725
- Device tree bindings and support.
- Voltage reference selection.
* ti-adc0832
- Triggered buffer support.
* ti-adc161s626
- Add regulator support allowing _scale and _offset values to be established
and exported.
New features (Tools)
* iio_generic_buffer
- -A option to force enable all channels rather than faulting if some are
already enabled (like -a does). Followup patches tidied this support up.
Cleanups (Core)
- Use kmalloc_array in iio_scan_mask_set.
- Take event_attrs field of iio_info structure constant
- Staging todo list updates. Most of it was long done.
- MAINTAINERS had a wrong directory listing.
Cleanups (Drivers)
* Missing i2c trivial devices entries.
* ad5592r
- Fix an endian type related sparse warnings.
* ad7150
- Constify the event attribute_group structures.
* ad7152
- Add some blank lines to improve readability.
- Sampling frequency control via chan-info element rather than hand rolled
attributes.
- add a new lock to avoid use of mlock for non state change related locking.
* ad7280
- Constify atrribute_group structure (second patch covers the event ones)
* ad7606 (Lars is driving most of the cleanup on this with some additions from
Eva)
- Fix improper setting of oversampling pins. This has been broken a very
long time in this staging driver, so not going to push this back to stable.
- Implement oversampling configuration via the chan_info mask element.
- Remove an unused int_vref_mv field.
- Remove a reundant name field from ad7606_chip_info.
- Remove default device configuration from platform_data in favour of
whatever the power on defaults are.
- Remove out of band error reporting in the kernel log as not providing
much information.
- Fix oversampling ratio by having 1 be the value for no oversampling.
- Avoid allocating buffer for each data capture.
- Factor out common code between periodic and one-shot capture.
- Move set_drvdat into common code.
- Let the common probe function return int rather than jumping through
an ERR_PTR.
- Pass struct device * into common remove to simplify code.
- Always run trigger handler only once per event (no one can remember why
it was being possibly done twice).
- Move over to the GPIO descriptor API to shorten and clarify code.
- Move the buffer code into the main file as it's not optional and is
now rather short in this driver.
- Fix the naming of the supply regulator.
- Rework regulator handling to handle errors including deferred probing.
- Tidy up a ptr_err or 0 return.
* ad7746
- Sampling frequency control via info_mask element rather than hand rolled
* ad7758
- Sampling frequency control via info_mask element rather than hand rolled
attributes.
* ad7816
- Constify the event attribute_group structure.
* adt7316
- Constify the event attribute group structures.
* ak8974
- Cleanup some sparse warnings about endian types.
* ak8975
- Cleanup some sparse warnings about endian types.
* bmi160
- Spare endian warning cleanups.
* isl29018 (towards staging graduation)
- Remove unusedvariables and defines.
- Improve consistency of error handling.
- Signed / unsigned comparison fixes.
- Use the IIO_DEVICE_ATTR_{RO, RW} macros
- Fix a race in in_illuminance_scale_available_show.
- Cleanup exit points of _read_raw
- Sanity check if in suspended state during a write_raw call as was already
done for read_raw.
- Document device tree bidnings.
- Document infrared supression controls.
- Add some newlines to improve readability and drop one that shouldn't be
there.
- Fix a poorly named functions name.
- Fix multiline coment syntax.
- Tidy up a pair or return statements by unifying them.
- Rename description in Kconfig for consistency with similar drivers.
* lidar
- cleanup power management by dropping unnecessary call.
* ltr501
- Use the claim_direct_mode helpers. Fix a race condition along the way.
* max1027
- Fix a dubious x | !y sparse warning.
- Use the new iio_trigger_validate_own_device helper.
* max440000
- Clean up some sparse warnings about endian types.
* mcp4725
- Use the regulator framework to establish the reference voltage rather than
getting it from platform data.
- Tidy up a comment typo.
- Fix a wrong PTR_ERR query (wrong regulator).
* mma7660
- Take a mma7660_nscale static.
* mma8452
- Use the new iio_trigger_validate_own_device helper.
- Use claim_direct_mode helpers - fix a race condition along the way.
* mpl3115
- Use claim_direct_mode helpers - fix a race condition along the way.
* ms65611
- Tidy up regulator error handling and clean out a static warning in the mix.
* sca3000
- Avoid a potential unitialized variable if a hardware read returns a value
that isn't actually supported (mostly warning supression).
- Fix a use before setting of the indio_dev->buffer pointer. Broken for
a very long time so not going to rush this into stable.
- Merge buffer file with core file. We used to always split these.
Sometimes it's just not worth the hassle. In this case the device's main
feature is it's hardware fifos so unlikely anyone would want to run it
without.
- Drop the sca3000_register_ring_funcs function as it's a pointless wrapper
once we have only one file.
- Fix cleaning of flag + setting of size of scan. Without this you can't
start the buffer twice and expect sensible (or any) results. Again,
broken for a long time so not heading for stable.
- Drop the custom watershed setting ABI - for now we'll just support one
value.
- Move to a hybrid hard / soft buffer design (how we've been doing it
for similar devices for a while now!)
- Cleanup some unusued variables.
- Use a fake channel to support core handling of freefall event registration.
- Cleanup the register defines.
- Fix an off by one error in axis due to IIO_NO_MOD taking up the 0 value.
Been broken since first admission of IIO to the staging tree.
- Add readback of the 3db low pass filter frequency and later writing
allowing droppign of custom measurement mode attributes as they can
be represented by the filter choices that is their main characteristic.
- Drop non standard revision attr and replace with dev_info on probe.
- Avoid a race in probe.
- Various formatting fixes.
- Kernel-docify docs that were very nearly in the write format.
* tsl2583
- Constify attribute_group structure.
* zpa2326
- Drop a redundant DEBUG ifdef.
Cleanups (Tools)
* iio_generic_buffer
- Fix the ? arguement. Previously it sort of worked as you got the help
message as a result of it not recognising the arguement.
Driver was checking for direct mode but not locking it. Use
claim/release helper functions to guarantee the device stays
in direct mode during raw reads.
Signed-off-by: Alison Schofield <amsfield22@gmail.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Change in handling of the regulator description means that static
checkers correctly assume we could be using dereferenced pointer to the
regulator. In reality we will never get the -ENODEV error, as current
behavior flow does not predict it, because:
If the device tree or board file does not define suitable regulators for
the component, it will be substituted by a dummy regulator, or, if
regulators are disabled altogether, by stubs.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Suggested-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Crt Mori <cmo@melexis.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Here is the big staging and IIO driver pull request for 4.9-rc1.
There are a lot of patches in here, the majority due to the
drivers/staging/greybus/ subsystem being merged in with full development
history that went back a few years, in order to preserve the work that
those developers did over time. This was done the same way that btrfs
was merged into the tree, so all should be ok there.
Lots and lots of tiny cleanups happened in the tree as well, due to the
Outreachy application process and lots of other developers showing up
for the first time to clean code up. Along with those changes, we
deleted a wireless driver, and added a raspberrypi driver (currently
marked broken), and lots of new iio drivers.
Overall the tree still shrunk with more lines removed than added, about
10 thousand lines removed in total. Full details are in the very long
shortlog below.
All of this has been in the linux-next tree with no issues. There will
be some merge problems with other subsystem trees, but those are all
minor problems and shouldn't be hard to work out when they happen
(MAINTAINERS and some lustre build problems with the IB tree.)
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iFYEABECABYFAlf0qWIPHGdyZWdAa3JvYWguY29tAAoJEDFH1A3bLfsp9GkAoLMa
Dl/S8W02azDtKP893es5GXh3AJ4k8J9JlHgTS0RlzVJMvzkSZ2x7Vg==
=j18s
-----END PGP SIGNATURE-----
Merge tag 'staging-4.9-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging
Pull staging and IIO updates from Greg KH:
"Here is the big staging and IIO driver pull request for 4.9-rc1.
There are a lot of patches in here, the majority due to the
drivers/staging/greybus/ subsystem being merged in with full
development history that went back a few years, in order to preserve
the work that those developers did over time.
Lots and lots of tiny cleanups happened in the tree as well, due to
the Outreachy application process and lots of other developers showing
up for the first time to clean code up. Along with those changes, we
deleted a wireless driver, and added a raspberrypi driver (currently
marked broken), and lots of new iio drivers.
Overall the tree still shrunk with more lines removed than added,
about 10 thousand lines removed in total. Full details are in the very
long shortlog below.
All of this has been in the linux-next tree with no issues. There will
be some merge problems with other subsystem trees, but those are all
minor problems and shouldn't be hard to work out when they happen
(MAINTAINERS and some lustre build problems with the IB tree)"
And furter from me asking for clarification about greybus:
"Right now there is a phone from Motorola shipping with this code (a
slightly older version, but the same tree), so even though Ara is not
alive in the same form, the functionality is happening. We are working
with the developers of that phone to merge the newer stuff in with
their fork so they can use the upstream version in future versions of
their phone product line.
Toshiba has at least one chip shipping in their catalog that
needs/uses this protocol over a Unipro link, and rumor has it that
there might be more in the future.
There are also other users of the greybus protocols, there is a talk
next week at ELC that shows how it is being used across a network
connection to control a device, and previous ELC talks have showed the
protocol stack being used over USB to drive embedded Linux boards.
I've also talked to some people who are starting to work to add a host
controller driver to control arduinos as the greybus PHY protocols are
very useful to control a serial/i2c/spio/whatever device across a
random physical link, as it is a way to have a self-describing device
be attached to a host without needing manual configuration.
So yes, people are using it, and there is still the chance that it
will show up in a phone/laptop/tablet/whatever from Google in the
future as well, the tech isn't dead, even if the original large phone
project happens to be"
* tag 'staging-4.9-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging: (3703 commits)
Staging: fbtft: Fix bug in fbtft-core
staging: rtl8188eu: fix double unlock error in rtw_resume_process()
staging:r8188eu: remove GEN_MLME_EXT_HANDLER macro
staging:r8188eu: remove GEN_DRV_CMD_HANDLER macro
staging:r8188eu: remove GEN_EVT_CODE macro
staging:r8188eu: remove GEN_CMD_CODE macro
staging:r8188eu: remove pkt_newalloc member of the recv_buf structure
staging:r8188eu: remove rtw_handle_dualmac declaration
staging:r8188eu: remove (RGTRY|BSSID)_(OFT|SZ) macros
staging:r8188eu: change rtl8188e_process_phy_info function argument type
Staging: fsl-mc: Remove blank lines
Staging: fsl-mc: Fix unaligned * in block comments
Staging: comedi: Align the * in block comments
Staging : ks7010 : Fix block comments warninig
Staging: vt6655: Remove explicit NULL comparison using Coccinelle
staging: rtl8188eu: core: rtw_xmit: Use macros instead of constants
staging: rtl8188eu: core: rtw_xmit: Move constant of the right side
staging: dgnc: Fix lines longer than 80 characters
Staging: dgnc: constify attribute_group structures
Staging: most: hdm-dim2: constify attribute_group structures
...
This patch adds minimal driver for the Honeywell Amplified Basic
Pressure sensors series. Sensors are pretty simple but are
available in many variants:
- psi/mbar/kPa output,
- analog/i2c/spi,
- gage/differential measurement,
- different measure ranges etc.
Refer to datasheets for more details:
http://sensing.honeywell.com/honeywell-sensing-basic-board-mount-pressure-sensors-abp-series-datasheet-323005128-c-en.pdfhttp://sensing.honeywell.com/index.php%3Fci_id%3D45841
Driver internals:
- i2c only. measure request is done by the SMBUS QUICK cmd, so if the i2c
bus doesn't support it, it is required to send a dummy byte to trigger
measurement,
- since iio sysfs expects kilopascals, mbar-variants are treated as their
respective kPa-s, hence i2c id-table has doubled entries in one line:
{ "abp060mg", ABP006KG }, { "abp006kg", ABP006KG },
- psi-variants have prescaled values in config,
- no temperature reads yet.
Work remained:
- optional temperature channel,
- SPI support,
- DT binding.
Changes since v1:
- mutex is now locked in read_raw(),
- corrected error codes,
- fixed coding style issues,
- renamed few defines and functions abp -> abp060mg
(some structs left as they were to keep the sensible meaning).
Signed-off-by: Marcin Malagowski <mrc@bourne.st>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
The -Wempty-body gcc warning triggers in the newly added zpa2326 driver:
drivers/iio/pressure/zpa2326.c: In function 'zpa2326_dequeue_pressure':
drivers/iio/pressure/zpa2326.c:578:3: error: suggest braces around empty body in an 'if' statement [-Werror=empty-body]
The use of an empty statement behind 'if (...)' is harmless here, but
it shows that the dev_dbg() macro is not used correctly: when the "DEBUG"
macro is not set, dev_dbg() already defaults to a no-operation, though
one that lets the compiler know that the arguments are used, and lets
it check the format string.
Fixing this also simplifies the driver.
Fixes: 03b262f2bb ("iio:pressure: initial zpa2326 barometer support")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
New device support
* ad8801 dac
- new driver supporting ad8801 and ad8803 DACs.
* adc12138
- new driver supporting TI adc12130/adc12132 and adc12138 ADCs.
* ltc2485 adc
- new driver
* mxc6255
- add support for the mxc6225 part name and fixup the ID check so it works.
* vz89x VOC sensor
- add support for the vz89te part which drops the voc_short channel and adds
CRCs compared to other supported parts.
New features
* core
- immutable triggers. These effectively grant exclusive control over a
trigger. The typical usecase is a device representing an analog part
(perhaps a MUX) that needs to control the sampling of a downstream
ADC.
- resource managed trigger registration and triggered_buffer_init.
- iio_push_event now protected against case of the event interface
registration not having yet occured. Only matters if an interrupt
can occur during this window - might happen on shared interrupt lines.
- helper to let a driver query if the trigger it is using is provided by
itself (using the convention of both device and trigger having the same
parent).
* tools
- iio-utils. Used channel modifier scaling in preference to generic scaling
when both exist.
* at91-adc
- Add support for touchscreen switches closure time needed by some newer
parts.
* stx104
- support the ADC channels on this ADC/DAC board. As these are the primary
feature of the board also move the driver to the iio/adc directory.
* sx9500
- device tree bindings.
Cleanups / Fixes
* ad5755
- fix an off-by-one on devnr limit check (introduced earlier this cycle)
* ad7266
- drop NULL check on devm_regulator_get_optional as it can't return NULL.
* ak8974
- avoid an unused functional warning due to rework in PM core code.
- remove .owner field setting as done by i2c_core.
* ina2xx
- clear out a left over debug field from chip global data.
* hid-sensors
- avoid an unused functional warning due to rework in PM core code.
* maxim-thermocouple
- fix non static symbol warnings.
* ms5611
- fetch and enable regulators unconditionally when they aren't optional.
* sca3000
- whitespace cleanup.
* st_sensors
- fetch and enable regulators unconditionally rather than having them
supported as optional regulators (missunderstanding on my part amongst
others a while back)
- followup to previous patch fixes error checking on the regulators.
- mark symbols static where possible.
- use the 'is it my trigger' help function. This prevents the odd case
of another device triggering from the st-sensors trigger whilst the
st-sensors trigger is itself not using it but rather using say an hrtimer.
* ti-ads1015
- add missing of_node_put.
* vz89x
- rework to all support of new devices.
- prevent reading of a corrupted buffer.
- fixup a return value of 0/1 in a bool returning function.
Address updates
- Vlad Dogaru email address change.
-----BEGIN PGP SIGNATURE-----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=V1xL
-----END PGP SIGNATURE-----
Merge tag 'iio-for-4.9b' of git://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio into staging-next
Jonathan writes:
Second set of iio new device support, features and cleanups for the 4.9 cycle.
New device support
* ad8801 dac
- new driver supporting ad8801 and ad8803 DACs.
* adc12138
- new driver supporting TI adc12130/adc12132 and adc12138 ADCs.
* ltc2485 adc
- new driver
* mxc6255
- add support for the mxc6225 part name and fixup the ID check so it works.
* vz89x VOC sensor
- add support for the vz89te part which drops the voc_short channel and adds
CRCs compared to other supported parts.
New features
* core
- immutable triggers. These effectively grant exclusive control over a
trigger. The typical usecase is a device representing an analog part
(perhaps a MUX) that needs to control the sampling of a downstream
ADC.
- resource managed trigger registration and triggered_buffer_init.
- iio_push_event now protected against case of the event interface
registration not having yet occured. Only matters if an interrupt
can occur during this window - might happen on shared interrupt lines.
- helper to let a driver query if the trigger it is using is provided by
itself (using the convention of both device and trigger having the same
parent).
* tools
- iio-utils. Used channel modifier scaling in preference to generic scaling
when both exist.
* at91-adc
- Add support for touchscreen switches closure time needed by some newer
parts.
* stx104
- support the ADC channels on this ADC/DAC board. As these are the primary
feature of the board also move the driver to the iio/adc directory.
* sx9500
- device tree bindings.
Cleanups / Fixes
* ad5755
- fix an off-by-one on devnr limit check (introduced earlier this cycle)
* ad7266
- drop NULL check on devm_regulator_get_optional as it can't return NULL.
* ak8974
- avoid an unused functional warning due to rework in PM core code.
- remove .owner field setting as done by i2c_core.
* ina2xx
- clear out a left over debug field from chip global data.
* hid-sensors
- avoid an unused functional warning due to rework in PM core code.
* maxim-thermocouple
- fix non static symbol warnings.
* ms5611
- fetch and enable regulators unconditionally when they aren't optional.
* sca3000
- whitespace cleanup.
* st_sensors
- fetch and enable regulators unconditionally rather than having them
supported as optional regulators (missunderstanding on my part amongst
others a while back)
- followup to previous patch fixes error checking on the regulators.
- mark symbols static where possible.
- use the 'is it my trigger' help function. This prevents the odd case
of another device triggering from the st-sensors trigger whilst the
st-sensors trigger is itself not using it but rather using say an hrtimer.
* ti-ads1015
- add missing of_node_put.
* vz89x
- rework to all support of new devices.
- prevent reading of a corrupted buffer.
- fixup a return value of 0/1 in a bool returning function.
Address updates
- Vlad Dogaru email address change.
This patch is inspired by a comment of Jonathan Cameron on patch of
Linus Walleij commit aeb55fff38 ("iio: st_sensors: fetch and enable regulators unconditionally").
The explanation for this change is same as in that patch:
"Supplies are *not* optional (optional means that the supply is
optional in the electrical sense, not the software sense) so we need to
get the and enable them at all times.
If the device tree or board file does not define suitable regulators for
the component, it will be substituted by a dummy regulator, or, if
regulators are disabled altogether, by stubs. There is no need to use the
IS_ERR_OR_NULL() check that is considered harmful.
Reported-by: Linus Wallerij <linus.walleij@linaro.org>
Suggested-by: Jonathan Cameron <jic23@kernel.org>
Signed-off-by: Crt Mori <cmo@melexis.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Patches merged to the IIO BMP085 driver makes it fully compliant
with all features found in this old misc driver. Retire this old
driver in favor of the new one in the proper subsystem.
Cc: Jonathan Cameron <jic23@cam.ac.uk>
Cc: Marek Belisko <marek@goldelico.com>
Acked-by: H. Nikolaus Schaller <hns@goldelico.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In commit 3d838118c6 ("iio: pressure: bmp280: add power management")
For some reason the code in the runtime suspend/resume hooks
got wrong (I suspect in the ambition to cut down boilerplate)
and it seems it was tested without CONFIG_PM and crashes like
so for me:
Unable to handle kernel NULL pointer dereference at virtual address 0000000c
pgd = c0204000
[0000000c] *pgd=00000000
Internal error: Oops: 5 [#1] PREEMPT SMP ARM
Modules linked in:
CPU: 1 PID: 89 Comm: kworker/1:2 Not tainted
4.7.0-03348-g90dc3680458a-dirty #99
Hardware name: Generic DT based system
Workqueue: pm pm_runtime_work
task: df3c6300 ti: dec8a000 task.ti: dec8a000
PC is at regulator_disable+0x0/0x6c
LR is at bmp280_runtime_suspend+0x3c/0xa4
Dereferencing the BMP280 state container properly fixes the problem,
sorry for screwing up.
Fixes: 3d838118c6 ("iio: pressure: bmp280: add power management")
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Tested-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
PTR_ERR should access the value just tested by IS_ERR, otherwise
the wrong error code will be returned.
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Some static channels are explicitly initialized with default values.
Remove them to enhance readability.
Signed-off-by: Gregor Boirie <gregor.boirie@parrot.com>
Tested-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Enable support for triggered buffering of temperature samples.
Signed-off-by: Gregor Boirie <gregor.boirie@parrot.com>
Tested-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Details scaling factors and offsets applied to raw temperature and pressure
samples.
Signed-off-by: Gregor Boirie <gregor.boirie@parrot.com>
Tested-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Sampled pressure data are 24 bits long and should be stored in a 32 bits
word.
Signed-off-by: Gregor Boirie <gregor.boirie@parrot.com>
Tested-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
The calibration data is described as coming from an E2PROM and that
means it does not change. Just read it once at probe time and store
it in the device state container. Also toss the calibration data
into the entropy pool since it is device unique.
Reviewed-by: Vlad Dogaru <vlad.dogaru@intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
The PM280 has an internal standby-mode, but to really save power
we should shut the sensor down and disconnect the power. With
the proper .pm hooks we can enable both runtime and system power
management of the sensor. We use the *force callbacks from the
system PM hooks. When the sensor comes back we always reconfigure
it to make sure it is ready to roll as expected.
Cc: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
The first version of this sensor, BMP085, supports sending an
End-of-Conversion (EOC) interrupt. Add code to support this using
a completion, in a similar vein as drivers/misc/bmp085.c does.
Make sure to check that we are given a rising edge, because the
EOC line goes from low-to-high when the conversion is ready.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
This patch mimics the SPI functionality found in the misc driver in
drivers/misc/bh085-spi.c to make it possible to reuse the existing
BMP280/BMP180/BMP085 driver with all clients of the other driver.
The adoption is straight-forward since like the other driver, it is
a simple matter of using regmap.
This driver is also so obviously inspired/copied from the old misc
driver in drivers/misc/bmp085.c that I just took the liberty to
add in the authors of the other drivers + self in the core driver
file.
The MISC driver also supports a variant named "BMP181" so include
that here to be complete in comparison to the old driver.
The bus mapping code for SPI was written by Akinobu Mita.
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Tested-by: Akinobu Mita <akinobu.mita@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
This creates a separate BMP280_I2C Kconfig entry that gets selected
by BMP280 for I2C transport. As we currently only support I2C
transport there is not much practical change other than getting
a separate object file (or module) for the I2C driver part. The
old Kconfig symbol BMP280 will still select the stuff we need so
that oldconfig and old defconfigs works fine.
Tested-by: Akinobu Mita <akinobu.mita@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
This splits the BMP280 driver in three logical parts: the core driver
bmp280-core that only operated on a struct device * and a struct regmap *,
the regmap driver bmp280-regmap that can be shared between I2C and other
transports and the I2C module driver bmp280-i2c.
Cleverly bake all functionality into a single object bmp280.o so that
we still get the same module binary built for the device in the end,
without any fuzz exporting symbols to the left and right.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
The BMP085/BMP180/BMP280 is supplied with two power sources:
VDDA (analog power) and VDDD (digital power). As these may come
from regulators (as on the APQ8060 Dragonboard) we need the driver
to attempt to fetch and enable these regulators.
We FAIL if we cannot: boards should either define:
- Proper regulators if present
- Define fixed regulators if power is hardwired to the component
- Rely on dummy regulators (will be present on all DT systems and
any boardfile system that calls regulator_has_full_constraints().
Cc: Mark Brown <broonie@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
On the APQ8060 Dragonboard the reset line to the BMP085 pressure
sensor is not deasserted on boot, so the driver needs to handle
this. For a simple GPIO line supplied as a descriptor (from a board
file, device tree or ACPI) this does the trick.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
This adds device tree support to the BMP085, BMP180 and BMP280
pressure sensors. Tested on the Qualcomm APQ8060 Dragonboard:
iio:device1$ cat in_temp_input
26700
iio:device1$ cat in_pressure_input
99.185000000
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Adds a new per-device sysfs attribute "current_timestamp_clock" to allow
userspace to select a particular POSIX clock for buffered samples and
events timestamping.
Following clocks, as listed in clock_gettime(2), are supported:
CLOCK_REALTIME, CLOCK_MONOTONIC, CLOCK_MONOTONIC_RAW,
CLOCK_REALTIME_COARSE, CLOCK_MONOTONIC_COARSE, CLOCK_BOOTTIME and
CLOCK_TAI.
Signed-off-by: Gregor Boirie <gregor.boirie@parrot.com>
Acked-by: Sanchayan Maity <maitysanchayan@gmail.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Firstly some contact detail updates:
* NXP took over freescale. Update the mma8452 header to reflect this.
* Martin Kepplinger email address change in mma8452 header.
* Adriana Reus has changed email address. Update .mailmap.
* Matt Ranostay has changed email address. Update .mailmap.
New Device Support
* max1363
- add the missing i2c_device_ids for a couple of parts so they can actually
be used.
* ms5867
- add device ids for ms5805 and ms5837 parts.
New Features
* ad5755
- DT support. This one was a bit controversial and under review for a long
time. Still no one could come up with a better solution.
* stx104
- add gpio support
* ti-adc081c
- Add ACPI device ID matching.
Core changes
* Refuse to register triggers with duplicate names. There is no way to
distinguish between them so this makes no sense. A few drivers do not
generate unique names for each instance of the device present. We can't
fix this without changing ABI so leave them and wait for someone to
actually take the rare step of two identical accelerometers on the same
board.
* buffer-dma
- use ARRAY_SIZE in a few appropriate locations.
Tools
* Fix the fact that the --trigger-num option in generic_buffer didn't allow
0 which is perfectly valid in the ABI.
Cleanups
* as3935
- improve error reporting.
- remove redundant zeroing of a field in iio_priv.
* gp2ap020a00f
- use the iio_device_claim_*_mode helpers rather than open coding locking
around mode changes.
* isl29125
- use the iio_device_claim_*_mode helpers rather than open coding locking.
* lidar
- use the iio_device_claim_*_mode helpers rather than open coding locking.
* mma8452
- more detail in devices supported description in comments (addresses and
similar)
* sca3000
- add a missing error check.
* tcs3414
- use the iio_device_claim_*_mode helpers rather than open coding locking.
* tcs3472
- use the iio_device_claim_*_mode helpers rather than open coding locking.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=6Lja
-----END PGP SIGNATURE-----
Merge tag 'iio-for-4.8b' of git://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio into staging-next
Jonathan writes:
Second round of new iio device support, features and cleanups in the 4.8 cycle
Firstly some contact detail updates:
* NXP took over freescale. Update the mma8452 header to reflect this.
* Martin Kepplinger email address change in mma8452 header.
* Adriana Reus has changed email address. Update .mailmap.
* Matt Ranostay has changed email address. Update .mailmap.
New Device Support
* max1363
- add the missing i2c_device_ids for a couple of parts so they can actually
be used.
* ms5867
- add device ids for ms5805 and ms5837 parts.
New Features
* ad5755
- DT support. This one was a bit controversial and under review for a long
time. Still no one could come up with a better solution.
* stx104
- add gpio support
* ti-adc081c
- Add ACPI device ID matching.
Core changes
* Refuse to register triggers with duplicate names. There is no way to
distinguish between them so this makes no sense. A few drivers do not
generate unique names for each instance of the device present. We can't
fix this without changing ABI so leave them and wait for someone to
actually take the rare step of two identical accelerometers on the same
board.
* buffer-dma
- use ARRAY_SIZE in a few appropriate locations.
Tools
* Fix the fact that the --trigger-num option in generic_buffer didn't allow
0 which is perfectly valid in the ABI.
Cleanups
* as3935
- improve error reporting.
- remove redundant zeroing of a field in iio_priv.
* gp2ap020a00f
- use the iio_device_claim_*_mode helpers rather than open coding locking
around mode changes.
* isl29125
- use the iio_device_claim_*_mode helpers rather than open coding locking.
* lidar
- use the iio_device_claim_*_mode helpers rather than open coding locking.
* mma8452
- more detail in devices supported description in comments (addresses and
similar)
* sca3000
- add a missing error check.
* tcs3414
- use the iio_device_claim_*_mode helpers rather than open coding locking.
* tcs3472
- use the iio_device_claim_*_mode helpers rather than open coding locking.
We want the fixes in here, and we can resolve a merge issue in
drivers/iio/industrialio-trigger.c
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 98ad8b41f58dff6b30713d7f09ae3834b8df7ded
("iio: st_sensors: verify interrupt event to status") caused
a regression when reading ST sensors from a HRTimer trigger
rather than the intrinsic interrupts: the HRTimer may
trigger faster than the sensor provides new values, and
as the check against new values available as a cause of
the interrupt trigger was done in the poll function,
this would bail out of the HRTimer interrupt with
IRQ_NONE.
So clearly we need to only check the new values available
from the proper interrupt handler and not from the poll
function, which should rather just read the raw values
from the registers, put them into the buffer and be happy.
To achieve this: switch the ST Sensors over to using a true
threaded interrupt handler.
In the interrupt thread, check if new values are available,
else yield to the (potential) next device on the same
interrupt line to check the registers. If the interrupt
was ours, proceed to poll the values.
Instead of relying on iio_trigger_generic_data_rdy_poll() as
a top half to wake up the thread that polls the sensor for
new data, have the thread call iio_trigger_poll_chained()
after determining that is is the proper source of the
interrupt. This is modelled on drivers/iio/accel/mma8452.c
which is already using a properly threaded interrupt handler.
In order to get the same precision in timestamps as
previously, where samples would be timestamped in the
poll function pf->timestamp when calling
iio_trigger_generic_data_rdy_poll() we introduce a
local timestamp in the sensor data, set it in the top half
(fastpath) of the interrupt handler and provide that to the
core when calling iio_push_to_buffers_with_timestamp().
Additionally: if the active scanmask is not set for the
sensor no IRQs should be enabled and we need to bail out
with IRQ_NONE. This can happen if spurious IRQs fire when
installing the threaded interrupt handler.
Tested with hard interrupt triggers on LIS331DL, then also
tested with hrtimers on the same sensor by creating a 75Hz
HRTimer and using it to poll the sensor.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Cc: Giuseppe Barba <giuseppe.barba@st.com>
Cc: Denis Ciocca <denis.ciocca@st.com>
Reported-by: Crestez Dan Leonard <cdleonard@gmail.com>
Tested-by: Crestez Dan Leonard <cdleonard@gmail.com>
Tested-by: Jonathan Cameron <jic23@kernel.org>
Fixes: 97865fe413 ("iio: st_sensors: verify interrupt event to status")
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Ensure failure to enable power regulators is properly handled.
Signed-off-by: Gregor Boirie <gregor.boirie@parrot.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Temperature channels report scaled samples in Celsius although expected as
milli degree Celsius in Documentation/ABI/testing/sysfs-bus-iio.
Gains are not implemented at all for LPS001WP pressure and temperature
channels.
This patch ensures that proper offsets and scales are exposed to userpace
for both pressure and temperature channels.
Also fix a NULL pointer exception when userspace reads content of sysfs
scale attribute when gains are not defined.
Signed-off-by: Gregor Boirie <gregor.boirie@parrot.com>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Initial support for ST LPS22HB pressure sensor. Datasheet:
http://www2.st.com/resource/en/datasheet/lps22hb.pdf
Features:
* pressure data and timestamping channels
* sampling frequency selection
* interrupt based trigger
* over I2C or SPI
Signed-off-by: Gregor Boirie <gregor.boirie@parrot.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Enable humidity support for the BME280 part
Signed-off-by: Matt Ranostay <matt.ranostay@intel.com>
Acked-by: Vlad Dogaru <vlad.dogaru@intel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
The I2C drivers have an i2c_device_id array but that information isn't
exported to the modules using the MODULE_DEVICE_TABLE() macro. So the
modules autoloading won't work if the I2C device is registered using
OF or legacy board files due missing alias information in the modules.
The issue was found using Kieran Bingham's coccinelle semantic patch:
https://lkml.org/lkml/2016/5/10/520
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
The bmp280 driver also supports BMP180 which has a different chip id
with BMP280. The probe routine verifies that the device reports the
correct chip id but the error message is confusing as if BMP280's chip
id is always expected.
Reported-by: Matt Ranostay <mranostay@gmail.com>
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Cc: Matt Ranostay <mranostay@gmail.com>
Cc: Vlad Dogaru <vlad.dogaru@intel.com>
Cc: Christoph Mair <christoph.mair@gmail.com>
Cc: Jonathan Cameron <jic23@kernel.org>
Cc: Hartmut Knaack <knaack.h@gmx.de>
Cc: Lars-Peter Clausen <lars@metafoo.de>
Cc: Peter Meerwald <pmeerw@pmeerw.net>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
This adds ability to control the oversampling ratio of the temperature
and pressure measurement for both bmp180 and bmp280.
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Acked-by: Vlad Dogaru <vlad.dogaru@intel.com>
Cc: Christoph Mair <christoph.mair@gmail.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
This adds support for the BMP180 to the bmp280 iio driver.
The BMP180 has already been supported by misc/bmp085 driver but it
doesn't use iio framework. This change adds the kconfig dependency
not to be selected both of them in order to avoid any issues.
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Acked-by: Vlad Dogaru <vlad.dogaru@intel.com>
Cc: Christoph Mair <christoph.mair@gmail.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Add support for HopeRF pressure and temperature sensor.
This device uses two fixed I2C addresses, one for storing
calibration coefficients and another for accessing the ADC.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Matt Ranostay <mranostay@gmail.com>
Cc: Jonathan Cameron <jic23@kernel.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Some types of ST Sensors can be connected to the same IRQ line
as other peripherals using open drain. Add a device tree binding
and a sensor data property to flip the right bit in the interrupt
control register to enable open drain mode on the INT line.
If the line is set to be open drain, also tag on IRQF_SHARED
to the IRQ flags when requesting the interrupt, as the whole
point of using open drain interrupt lines is to share them with
more than one peripheral (wire-or).
Cc: devicetree@vger.kernel.org
Cc: Giuseppe Barba <giuseppe.barba@st.com>
Cc: Denis Ciocca <denis.ciocca@st.com>
Acked-by: Rob Herring <rob@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
This makes all ST sensor drivers check that they actually have
new data available for the requested channel(s) before claiming
an IRQ, by reading the status register (which is conveniently
the same for all ST sensors) and check that the channel has new
data before proceeding to read it and fill the buffer.
This way sensors can share an interrupt line: it can be flaged
as shared and then the sensor that did not fire will return
NO_IRQ, and the sensor that fired will handle the IRQ and
return IRQ_HANDLED.
Cc: Giuseppe Barba <giuseppe.barba@st.com>
Cc: Denis Ciocca <denis.ciocca@st.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
This fixes the errors reported by checkpatch.pl:
ERROR: code indent should use tabs where possible
Signed-off-by: Slawomir Stepien <sst@poczta.fm>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Ensure optional regulator is properly disabled when present.
Fixes: 3145229f91 ("iio:pressure:ms5611: power regulator support")
Signed-off-by: Gregor Boirie <gregor.boirie@parrot.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Add support for setting and retrieving OverSampling Rate independently for
each of the temperature and pressure channels. This allows userspace to
fine tune hardware sampling process according to the following tradeoffs :
* the higher the OSR, the finer the resolution ;
* the higher the OSR, the lower the noise ;
BUT:
* the higher the OSR, the larger the drift ;
* the higher the OSR, the longer the response time, i.e. less samples per
unit of time.
Signed-off-by: Gregor Boirie <gregor.boirie@parrot.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Add device-tree ID tables and document bindings.
Signed-off-by: Gregor Boirie <gregor.boirie@parrot.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Previously most drivers that used a i2c_check_functionality() check
condition required various error codes on failure. This patchset
converts to a standard of -EOPNOTSUPP
Signed-off-by: Matt Ranostay <mranostay@gmail.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Add support for an optional regulator which, if found into device-tree,
will power on device at probing time.
The regulator is declared into ms5611 DTS entry as a "vdd-supply" property.
Signed-off-by: Gregor Boirie <gregor.boirie@parrot.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Use name of probed device instead of driver's one when registering device.
Signed-off-by: Gregor Boirie <gregor.boirie@parrot.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Computation of sens2 was wrong and is fixed by this patch, sens2 should be:
2 * (t - 2000)^2
See page 8 of ms5607 datasheet here:
http://www.meas-spec.com/product/pressure/MS5607-02BA03.aspx
Signed-off-by: Gregor Boirie <gregor.boirie@parrot.com>
Acked-by: Lucas De Marchi <lucas.demarchi@intel.com>
Acked-by: Peter Meerwald-Stadler <pmeerw@pmeerw.net>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
The ms5611 driver started using the IIO_TRIGGERED_BUFFER infrastructure
which in turn depend on IIO_BUFFER, and it produces a build error now
if that is not enabled:
warning: (... && MS5611 && ...) selects IIO_TRIGGERED_BUFFER which has unmet direct dependencies (IIO && IIO_BUFFER)
buffer/industrialio-triggered-buffer.c: In function 'iio_triggered_buffer_setup':
buffer/industrialio-triggered-buffer.c:58:2: error: implicit declaration of function 'iio_device_attach_buffer' [-Werror=implicit-function-declaration]
pressure/ms5611_core.c: In function 'ms5611_trigger_handler':
pressure/ms5611_core.c:193:2: error: implicit declaration of function 'iio_push_to_buffers_with_timestamp' [-Werror=implicit-function-declaration]
This adds the second select.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Fixes: 713bbb4efb ("iio: pressure: ms5611: Add triggered buffer support")
Acked-by: Daniel Baluta <daniel.baluta@intel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
New Device Support
* Apex stx104 DAC
- new driver for this PC104 board. Right now DAC support only.
* ADI ad5064
- Add support for ad5625, ad5627, ad5645, ad5665, ad5667 DACs.
- Add support for Linear Technology ltc2606, ltc2607, ltc2609, ltc2616,
ltc2617, ltc2619, ltc2626, ltc2627 and ltc2629.
* ADI ad7192
- add support for the ad7193
* Invensense mpu6050
- substantial rework of driver to use regmap allowing SPI support extending
the now split driver to cover the MPU6000.
* TI adc0832
- new driver supporting ADC0831, ADC0832, ADC0834 and ADC0838 ADCs.
* TI ads1015
- new driver, note that there is an existing hwmon driver. The long term
intention is to probably remove the hwmon driver but for now we just have
guards in place to ensure this driver is not built if that one is enabled.
* TI afe4403
- new driver for this heart rate monitor / pulse oximeter front end chip.
* TI afe4404
- new driver for this heart rate monitor / pulse oximeter front end chip.
Staging Graduations
* mxs-lradc
- A combined general purpose and touch screen (input) device driver.
Originally held in staging to allow reworking into and MFD but as
that wasn't happening and isn't an absolute requirement we are moving
it out of staging.
Driver new features
* ms5611
- triggered buffer support
- IIO_CHAN_INFO_SCALE to aid the triggered buffer support.
Driver cleanups / reworks / fixes
* ad5064
- Use an enum for the register map layout to allow support of additional
chips (precursor to the new support listed above).
- Structural driver changes to allow support of the slightly different
handling for the ltc parts above.
* ad5933
- drop an exceptional & unnecessary for a function pointer.
* ad7606
- Cleanup the repeated copies of pm ops.
- consolidate the various channels specs via a sport of rearranging so only
one version is needed.
* atlas ph sensor
- add select IRQ_WORK
* hmc8543 (soon to move out of staging)
- Comment style fixes
- functionality of suspend and resume was swapped.
* spear-adc
- use devm_clk_dev instead of managing the clk lifetime by hand.
Core
* Use new dmaengine_terminate_sync call to avoid a theoretical race.
* Fix docs for mlock in struct iio_dev as it is correctly taken in some
drivers (docs used to say for core only).
* Add a helper function for calculating the scan index storage size within
the core cutting out some cut and paste versions of the same code.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=LIQe
-----END PGP SIGNATURE-----
Merge tag 'iio-for-4.6b' of git://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio into staging-next
Jonathan writes:
2nd round of new IIO device support, features and cleanups for the 4.6 cycle.
New Device Support
* Apex stx104 DAC
- new driver for this PC104 board. Right now DAC support only.
* ADI ad5064
- Add support for ad5625, ad5627, ad5645, ad5665, ad5667 DACs.
- Add support for Linear Technology ltc2606, ltc2607, ltc2609, ltc2616,
ltc2617, ltc2619, ltc2626, ltc2627 and ltc2629.
* ADI ad7192
- add support for the ad7193
* Invensense mpu6050
- substantial rework of driver to use regmap allowing SPI support extending
the now split driver to cover the MPU6000.
* TI adc0832
- new driver supporting ADC0831, ADC0832, ADC0834 and ADC0838 ADCs.
* TI ads1015
- new driver, note that there is an existing hwmon driver. The long term
intention is to probably remove the hwmon driver but for now we just have
guards in place to ensure this driver is not built if that one is enabled.
* TI afe4403
- new driver for this heart rate monitor / pulse oximeter front end chip.
* TI afe4404
- new driver for this heart rate monitor / pulse oximeter front end chip.
Staging Graduations
* mxs-lradc
- A combined general purpose and touch screen (input) device driver.
Originally held in staging to allow reworking into and MFD but as
that wasn't happening and isn't an absolute requirement we are moving
it out of staging.
Driver new features
* ms5611
- triggered buffer support
- IIO_CHAN_INFO_SCALE to aid the triggered buffer support.
Driver cleanups / reworks / fixes
* ad5064
- Use an enum for the register map layout to allow support of additional
chips (precursor to the new support listed above).
- Structural driver changes to allow support of the slightly different
handling for the ltc parts above.
* ad5933
- drop an exceptional & unnecessary for a function pointer.
* ad7606
- Cleanup the repeated copies of pm ops.
- consolidate the various channels specs via a sport of rearranging so only
one version is needed.
* atlas ph sensor
- add select IRQ_WORK
* hmc8543 (soon to move out of staging)
- Comment style fixes
- functionality of suspend and resume was swapped.
* spear-adc
- use devm_clk_dev instead of managing the clk lifetime by hand.
Core
* Use new dmaengine_terminate_sync call to avoid a theoretical race.
* Fix docs for mlock in struct iio_dev as it is correctly taken in some
drivers (docs used to say for core only).
* Add a helper function for calculating the scan index storage size within
the core cutting out some cut and paste versions of the same code.
This will be used together with an external trigger (e.g hrtimer
based software trigger).
Signed-off-by: Daniel Baluta <daniel.baluta@intel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
This allows data exported via buffer interface to be converted
to standard units in userspace.
Signed-off-by: Daniel Baluta <daniel.baluta@intel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Clearly a high degree of cut and paste has gone on in this file, propogating
a particularly random combination of tabs and spaces. This patch at least
should make it all consistent going forward.
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
mpl115 driver currently supports i2c interface (MPL115A2).
There is also SPI version (MPL115A1). The difference between them
is only physical transport so we can easily support both while sharing
most of the code.
Split the driver into a core support module and one module each for I2C
and SPI support.
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Cc: Jonathan Cameron <jic23@kernel.org>
Cc: Hartmut Knaack <knaack.h@gmx.de>
Cc: Lars-Peter Clausen <lars@metafoo.de>
Cc: Peter Meerwald <pmeerw@pmeerw.net>
Cc: linux-iio@vger.kernel.org
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
mpl115 sets i2c clientdata, but it is not used anywhere. So remove it.
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Cc: Jonathan Cameron <jic23@kernel.org>
Cc: Hartmut Knaack <knaack.h@gmx.de>
Cc: Lars-Peter Clausen <lars@metafoo.de>
Cc: Peter Meerwald <pmeerw@pmeerw.net>
Cc: linux-iio@vger.kernel.org
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
According to the datasheet, the resolusion of temperature sensor is
-5.35 counts/C. Temperature ADC is 472 counts at 25C.
(https://www.sparkfun.com/datasheets/Sensors/Pressure/MPL115A1.pdf
NOTE: This is older revision, but this information is removed from the
latest datasheet from nxp somehow)
Temp [C] = (Tadc - 472) / -5.35 + 25
= (Tadc - 605.750000) * -0.186915888
So the correct offset is -605.750000.
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Acked-by: Peter Meerwald-Stadler <pmeerw@pmeerw.net>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Most ST MEMS Sensors that support interrupts can also handle sending
an active low interrupt, i.e. going from high to low on data ready
(or other interrupt) and thus triggering on a falling edge to the
interrupt controller.
Set up logic to inspect the interrupt line we get for a sensor: if
it is triggering on rising edge, leave everything alone, but if it
triggers on falling edges, set up active low, and if unsupported
configurations appear: warn with errors and reconfigure the interrupt
to a rising edge, which all interrupt generating sensors support.
Create a local header for st_sensors_core.h to share functions
between the sensor core and the trigger setup code.
Cc: Giuseppe Barba <giuseppe.barba@st.com>
Cc: Denis Ciocca <denis.ciocca@st.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Quite a lot of activity in SPI this cycle, almost all of it in drivers
with a few minor improvements and tweaks in the core.
- Updates to pxa2xx to support Intel Broxton and multiple chip selects.
- Support for big endian in the bcm63xx driver.
- Multiple slave support for the mt8173
- New driver for the auxiliary SPI controller in bcm2835 SoCs.
- Support for Layerscale SoCs in the Freescale DSPI driver.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJWOehzAAoJECTWi3JdVIfQTPYH+wYMDG8gAIw2s0AJ4DvVe4qZ
sOAm1UgUJZxssrEA6BNqbfM0dfRo+oQJKmRd0Dc5n7LEMsYHdI/5yKHk8PCS6ZzD
iQyQCzbd0thDAqwuPaMP62cyPDHwyJX22VGTsgVnj6AZqAQ+9+g4SPKhFnm1Mlm4
hmDi6fdSrsqo8k8gkpVN8RFOfVsjAV1dLtAauQRWDHrqMxXURSrKG76eqAqUa5bn
BLPXBoj5PA0DMLPO2j+ADZwWN723LrI2mSSlc+ThjEX/OIt2OhAoiOTV5RPqaafy
TIsCkh68q/gYAsL5HtvvmgZByl41FLYiO0Z+rXmWUyMMbnvhZTLws9S2BNpBLuk=
=DgXG
-----END PGP SIGNATURE-----
Merge tag 'spi-v4.4' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi
Pull spi updates from Mark Brown:
"Quite a lot of activity in SPI this cycle, almost all of it in drivers
with a few minor improvements and tweaks in the core.
- Updates to pxa2xx to support Intel Broxton and multiple chip selects.
- Support for big endian in the bcm63xx driver.
- Multiple slave support for the mt8173
- New driver for the auxiliary SPI controller in bcm2835 SoCs.
- Support for Layerscale SoCs in the Freescale DSPI driver"
* tag 'spi-v4.4' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi: (87 commits)
spi: pxa2xx: Rework self-initiated platform data creation for non-ACPI
spi: pxa2xx: Add support for Intel Broxton
spi: pxa2xx: Detect number of enabled Intel LPSS SPI chip select signals
spi: pxa2xx: Add output control for multiple Intel LPSS chip selects
spi: pxa2xx: Use LPSS prefix for defines that are Intel LPSS specific
spi: Add DSPI support for layerscape family
spi: ti-qspi: improve ->remove() callback
spi/spi-xilinx: Fix race condition on last word read
spi: Drop owner assignment from spi_drivers
spi: Add THIS_MODULE to spi_driver in SPI core
spi: Setup the master controller driver before setting the chipselect
spi: dw: replace magic constant by DW_SPI_DR
spi: mediatek: mt8173 spi multiple devices support
spi: mediatek: handle controller_data in mtk_spi_setup
spi: mediatek: remove mtk_spi_config
spi: mediatek: Update document devicetree bindings to support multiple devices
spi: fix kernel-doc warnings about missing return desc in spi.c
spi: fix kernel-doc warnings about missing return desc in spi.h
spi: pxa2xx: Align a few defines
spi: pxa2xx: Save other reg_cs_ctrl bits when configuring chip select
...
An spi_driver does not need to set an owner, it will be populated by the
driver core.
Signed-off-by: Andrew F. Davis <afd@ti.com>
Acked-by: Jonathan Cameron <jic23@kernel.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Support for MS8607 temperature, pressure & humidity sensor.
This part is using functions from MS5637 for temperature and pressure
and HTU21 for humidity
Signed-off-by: Ludovic Tancerel <ludovic.tancerel@maplehightech.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Support for MS5637 temperature & pressure sensor
Signed-off-by: Ludovic Tancerel <ludovic.tancerel@maplehightech.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
This adds a debugfs hook to read/write registers in the ST
sensors using debugfs. Proved to be awesome help when trying
to debug why IRQs do not arrive.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Denis Ciocca <denis.ciocca@st.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
This patch permits to configure the WhoAmI register address
because some device could have not a standard address for
this register.
Signed-off-by: Giuseppe Barba <giuseppe.barba@st.com>
Reviewed-by: Denis Ciocca <denis.ciocca@st.com>
Acked-by: Denis Ciocca <denis.ciocca@st.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
i2c_driver does not need to set an owner because i2c_register_driver()
will set it.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
MS5607 is temperature and pressure sensor which hardware is similar to MS5611.
Both sensors share command protocol and support both I2C and SPI serial
protocols. They only differ in compensation algorithms.
Signed-off-by: Tomasz Duszynski <tduszyns@gmail.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
IIO_CHAN_INFO_SCALE is useful whenever conversion to standard units is done
in userspace. In this case conversion is handled by driver so this bit
is unnecessary.
Signed-off-by: Tomasz Duszynski <tduszyns@gmail.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Core functionality
* i and q modifiers from quadrature channels.
* IIO_CHAN_INFO_OVERSAMPLING_RATIO added.
* High pass filter attributes added to mirror the existing low pass filter
ones.
Core cleanups
* Make IIO tools building more cross compiler friendly.
* Substantial rework of the function __iio_update_buffers to greatly simplify
a hideously evolved function.
New drivers and support
* ACPI0008 ambient light sensor driver. This one has been around a long time to
will be good to finally get it into mainline.
* Berlin SOC ADC support.
* BMC150 magnetometer. The accelerometer in the same package has been supported
for quite some time, so good to have this half as well.
* m62332 DAC driver
* MEMSIC MMC35420 magnetometer.
* ROHM BH1710 and similar ambient light sensors.
* Sensortek STK3310 light sensor.
* Sensortek STK8312 accelerometer.
* Sensortek STK8BA50 accelerometer.
* ti-adc128s052 gains support form the adc122s021 2 channel ADC.
Driver cleanups and functionality.
* Allow various drivers to compile with !GPIOLIB if COMPILE_TEST enabled.
* bmc150 - decouple trigger from buffer to allow other triggers to be used.
* bmg160 - decouple trigger from buffer to allow other triggers to be used.
Fix a trivial unused field.
* Constify a load of platform_device_id structures.
* inv_mpu6050 - device tree bindings.
* hid-sensors - fix a memory leak during probe if certain errors occur.
* ltr501 - illuminance channel derived (in an non obvious fashion) from the
intensity channels.
* ltr501 - fix a boundary check on the proximity threshold.
* mlx90614 - drop a pointless return.
* mma8452 - Debugfs register access and fix a bug that had no effect (by
coincidence)
* ti_am335x_adc - add device tree bindings for sample-delay, open-delay and
averaging. The ideal settings for these tend to be board design specific.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=uX2k
-----END PGP SIGNATURE-----
Merge tag 'iio-for-v4.2b' of git://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio into staging-next
Jonathan writes:
Second set of new driver, functionality and cleanups for IIO in the 4.2 cycle.
Core functionality
* i and q modifiers from quadrature channels.
* IIO_CHAN_INFO_OVERSAMPLING_RATIO added.
* High pass filter attributes added to mirror the existing low pass filter
ones.
Core cleanups
* Make IIO tools building more cross compiler friendly.
* Substantial rework of the function __iio_update_buffers to greatly simplify
a hideously evolved function.
New drivers and support
* ACPI0008 ambient light sensor driver. This one has been around a long time to
will be good to finally get it into mainline.
* Berlin SOC ADC support.
* BMC150 magnetometer. The accelerometer in the same package has been supported
for quite some time, so good to have this half as well.
* m62332 DAC driver
* MEMSIC MMC35420 magnetometer.
* ROHM BH1710 and similar ambient light sensors.
* Sensortek STK3310 light sensor.
* Sensortek STK8312 accelerometer.
* Sensortek STK8BA50 accelerometer.
* ti-adc128s052 gains support form the adc122s021 2 channel ADC.
Driver cleanups and functionality.
* Allow various drivers to compile with !GPIOLIB if COMPILE_TEST enabled.
* bmc150 - decouple trigger from buffer to allow other triggers to be used.
* bmg160 - decouple trigger from buffer to allow other triggers to be used.
Fix a trivial unused field.
* Constify a load of platform_device_id structures.
* inv_mpu6050 - device tree bindings.
* hid-sensors - fix a memory leak during probe if certain errors occur.
* ltr501 - illuminance channel derived (in an non obvious fashion) from the
intensity channels.
* ltr501 - fix a boundary check on the proximity threshold.
* mlx90614 - drop a pointless return.
* mma8452 - Debugfs register access and fix a bug that had no effect (by
coincidence)
* ti_am335x_adc - add device tree bindings for sample-delay, open-delay and
averaging. The ideal settings for these tend to be board design specific.
'channels' is allocated via kmemdup and it is never freed in the
subsequent error paths.
Use 'indio_dev->channels' directly instead, so that we avoid such
memory leak problem.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Reviewed-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Second version of this pull request as a small fix to a fix turned
up before Greg pulled it for a cc10001 patch near the top of the tree.
One core fix
* Set updated for a iio kfifo was incorrectly set to false during a failed
update, resulting in atttempts to repeat the failed operation appearing
to succeed.
This time I've decided to list the driver fixes in alphabetical order rather
than 'randomly'.
* axp288_adc - a recent change added a check for valid info masks when
reading channels from consumer drivers.
* bmp280 - temperature compensation was failing to read the tfine value, hence
causing a temperature of 0 to always be returned and incorrect presure
measurements.
* cc10001 - Fix channel number mapping when some channels are reserved for
remote CPUs. Fix an issue with the use of the power-up/power-down register
(basically wrong polarity). Fix an issue due to the missinterpretting the
return value from regulator_get_voltage. Add a delay before the start bit
as recommended for the hardware to avoid data corruption.
* hid pressure - fix channel spec of modfiied, but no modifier (which makes no
sense!)
* hid proximity - fix channel spec of modified, but no modifier (which makes
no sense!). Fix a memory leak in the probe function.
* mcp320x - occasional incorrect readings on dma using spi busses due to
cacheline corruption. Fixed by forcing ___cacheline_aligned for the buffers.
* mma9551 - buffer overrun fix (miss specified maximum length of buffers)
* mma9553 - endian fix on status message. Add an enable element for activity
channel. Input checking for activity period to avoid rather unpredictable
results.
* spmi-vadc - fix an overflow in the output value normalization seen on some
boards.
* st-snesors - oops due to use of a mutex that is not yet initialized during
probe.
* xilinx adc - Some wrong register addresses, a wrong address for vccaux
channel, incorrect scale on VREFP and incorrect sign on VREFN.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=PiG+
-----END PGP SIGNATURE-----
Merge tag 'iio-fixes-for-4.1a-take2' of git://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio into staging-linus
Jonathan writes:
The usual mixed bag of fixes for IIO in the 4.1 cycle.
Second version of this pull request as a small fix to a fix turned
up before Greg pulled it for a cc10001 patch near the top of the tree.
One core fix
* Set updated for a iio kfifo was incorrectly set to false during a failed
update, resulting in atttempts to repeat the failed operation appearing
to succeed.
This time I've decided to list the driver fixes in alphabetical order rather
than 'randomly'.
* axp288_adc - a recent change added a check for valid info masks when
reading channels from consumer drivers.
* bmp280 - temperature compensation was failing to read the tfine value, hence
causing a temperature of 0 to always be returned and incorrect presure
measurements.
* cc10001 - Fix channel number mapping when some channels are reserved for
remote CPUs. Fix an issue with the use of the power-up/power-down register
(basically wrong polarity). Fix an issue due to the missinterpretting the
return value from regulator_get_voltage. Add a delay before the start bit
as recommended for the hardware to avoid data corruption.
* hid pressure - fix channel spec of modfiied, but no modifier (which makes no
sense!)
* hid proximity - fix channel spec of modified, but no modifier (which makes
no sense!). Fix a memory leak in the probe function.
* mcp320x - occasional incorrect readings on dma using spi busses due to
cacheline corruption. Fixed by forcing ___cacheline_aligned for the buffers.
* mma9551 - buffer overrun fix (miss specified maximum length of buffers)
* mma9553 - endian fix on status message. Add an enable element for activity
channel. Input checking for activity period to avoid rather unpredictable
results.
* spmi-vadc - fix an overflow in the output value normalization seen on some
boards.
* st-snesors - oops due to use of a mutex that is not yet initialized during
probe.
* xilinx adc - Some wrong register addresses, a wrong address for vccaux
channel, incorrect scale on VREFP and incorrect sign on VREFN.
The platform_device_id is not modified by the driver and core uses it as
const.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski.k@gmail.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
In SPI mode the transfer buffer is locked with a mutex. However this
mutex is only initilized after the probe, but some transfer needs to
be done in the probe.
To fix this bug we move the mutex initialization at the beginning of
the device probe.
Signed-off-by: Alban Bedel <alban.bedel@avionic-design.de>
Acked-by: Denis Ciocca <denis.ciocca@st.com>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Fix "null" in the raw attribute and scan elements.
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Pull HID updates from Jiri Kosina:
- quite a few firmware fixes for RMI driver by Andrew Duggan
- huion and uclogic drivers have been substantially overlaping in
functionality laterly. This redundancy is fixed by hid-huion driver
being merged into hid-uclogic; work done by Benjamin Tissoires and
Nikolai Kondrashov
- i2c-hid now supports ACPI GPIO interrupts; patch from Mika Westerberg
- Some of the quirks, that got separated into individual drivers, have
historically had EXPERT dependency. As HID subsystem matured (as
well as the individual drivers), this made less and less sense. This
dependency is now being removed by patch from Jean Delvare
- Logitech lg4ff driver received a couple of improvements for mode
switching, by Michal Malý
- multitouch driver now supports clickpads, patches by Benjamin
Tissoires and Seth Forshee
- hid-sensor framework received a substantial update; namely support
for Custom and Generic pages is being added; work done by Srinivas
Pandruvada
- wacom driver received substantial update; it now supports
i2c-conntected devices (Mika Westerberg), Bamboo PADs are now
properly supported (Benjamin Tissoires), much improved battery
reporting (Jason Gerecke) and pen proximity cleanups (Ping Cheng)
- small assorted fixes and device ID additions
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/hid: (68 commits)
HID: sensor: Update document for custom sensor
HID: sensor: Custom and Generic sensor support
HID: debug: fix error handling in hid_debug_events_read()
Input - mt: Fix input_mt_get_slot_by_key
HID: logitech-hidpp: fix error return code
HID: wacom: Add support for Cintiq 13HD Touch
HID: logitech-hidpp: add a module parameter to keep firmware gestures
HID: usbhid: yet another mouse with ALWAYS_POLL
HID: usbhid: more mice with ALWAYS_POLL
HID: wacom: set stylus_in_proximity before checking touch_down
HID: wacom: use wacom_wac_finger_count_touches to set touch_down
HID: wacom: remove hardcoded WACOM_QUIRK_MULTI_INPUT
HID: pidff: effect can't be NULL
HID: add quirk for PIXART OEM mouse used by HP
HID: add HP OEM mouse to quirk ALWAYS_POLL
HID: wacom: ask for a in-prox report when it was missed
HID: hid-sensor-hub: Fix sparse warning
HID: hid-sensor-hub: fix attribute read for logical usage id
HID: plantronics: fix Kconfig default
HID: pidff: support more than one concurrent effect
...
Temperature reads on bmp280 device always return 0,
due to a missing step in the compensation formula
(data->tfine is never initialized).
Initialize data->tfine value so we get correct
temperature and pressure values.
Signed-off-by: Irina Tirdea <irina.tirdea@intel.com>
Reviewed-by: Vlad Dogaru <vlad.dogaru@intel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Add support for Measurement Specialities MS5611 pressure
and temperature sensor.
Signed-off-by: Tomasz Duszynski <tduszyns@gmail.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Add additional flag to read in async mode. In this mode the caller will get
reply via registered callback for capture_sample. Callbacks can be registered
using sensor_hub_register_callback function. The usage id parameter of the
capture_sample can be matched with the usage id of the requested attribute.
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Acked-by: Jonathan Cameron <jic23@kernel.org>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Use common hid sensor iio pm functions. Also the poll time read and
wait is part of power up function of hid sensor iio pm function, so
remove from the client drivers.
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
The calculations for temperature and pressure compensation were already slightly
optimized in comparison to the datasheet. So, it makes sense to optimize even a
bit more, making proper use of C operators:
- variable t in bmp280_compensate_temp() can be eliminated by directly
returning the result of the relevant equation.
- make use of the += operator and eliminate an unnecessary parenthesis level in
bmp280_compensate_press().
When the initialization of the ctrl_meas register fails, the error message will
now mention the right register name.
During probe, i2c_set_clientdata() is called, although it is not necessary. Drop
it.
Signed-off-by: Hartmut Knaack <knaack.h@gmx.de>
Reviewed-by: Vlad Dogaru <vlad.dogaru@intel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
This version of the code avoids extra memory copy operations and is
somewhat smaller in code size.
Signed-off-by: Vlad Dogaru <vlad.dogaru@intel.com>
Acked-by: Hartmut Knaack <knaack.h@gmx.de>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
According to the datasheet and as defined in struct bmp280_comp_press, dig_p1 is
of type u16, while dig_p2 to dig_p9 are of type s16. In
bmp280_read_compensation_press(), values read from the device were treated as
the wrong type.
In bmp280_read_press() the fractional part of the measured pressure is
calculated wrong. A better way is to use *val for the raw pressure and *val2 for
the quotient and let the core do the proper conversion using IIO_VAL_FRACTIONAL.
Signed-off-by: Hartmut Knaack <knaack.h@gmx.de>
Acked-by: Vlad Dogaru <vlad.dogaru@intel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
The proper way to divide two signed 64-bit values is to use div64_s64.
Signed-off-by: Vlad Dogaru <vlad.dogaru@intel.com>
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
This patch fix pressure data variable name. Usually pdata name
it is used for platform data.
Signed-off-by: Denis Ciocca <denis.ciocca@st.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
This patch change structure name and related variables names.
Signed-off-by: Denis Ciocca <denis.ciocca@st.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
This patch removes the .owner field for drivers which use the
platform_driver_register api because this is overriden in
_platform_driver_register.
Signed-off-by: Sanjeev Sharma <Sanjeev_Sharma@mentor.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Marcin Niestroj