On a system with a defective USB device connected to an USB hub,
an endless sequence of port connect events was observed. The sequence
of events as observed is as follows:
- Port reports connected event (port status=USB_PORT_STAT_CONNECTION).
- Event handler debounces port and resets it by calling hub_port_reset().
- hub_port_reset() calls hub_port_wait_reset() to wait for the reset
to complete.
- The reset completes, but USB_PORT_STAT_CONNECTION is not immediately
set in the port status register.
- hub_port_wait_reset() returns -ENOTCONN.
- Port initialization sequence is aborted.
- A few milliseconds later, the port again reports a connected event,
and the sequence repeats.
This continues either forever or, randomly, stops if the connection
is already re-established when the port status is read. It results in
a high rate of udev events. This in turn destabilizes userspace since
the above sequence holds the device mutex pretty much continuously
and prevents userspace from actually reading the device status.
To prevent the problem from happening, let's wait for the connection
to be re-established after a port reset. If the device was actually
disconnected, the code will still return an error, but it will do so
only after the long reset timeout.
Cc: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Current implementation of init_vudc_hw() adds ep0 to ep_list
and then after looping through all endpoints removes it from
that list.
As this may be misleading let's refactor this function
and avoid adding and removing ep0 to eplist and place it
immediately in correct place.
In addition let's remove redundant 0 assignments as ep
array is zeroed during allocation.
Signed-off-by: Krzysztof Opasiak <k.opasiak@samsung.com>
Acked-by: Shuah Khan <shuahkh@osg.samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
ep_list inside gadget structure doesn't contain ep0.
It is stored separately in ep0 field.
This causes an urb hang if gadget driver decides to
delay setup handling. On host side this is visible as
timeout error when setting configuration.
This bug can be reproduced using for example any gadget
with mass storage function.
Fixes: abdb295743 ("usbip: vudc: Add vudc_transfer")
Signed-off-by: Krzysztof Opasiak <k.opasiak@samsung.com>
Cc: stable <stable@vger.kernel.org>
Acked-by: Shuah Khan <shuahkh@osg.samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
These updates include a new driver for Fintek F8153x devices, support
for the GPIO functionality on CP2105 devices, and improved support for
CH34X devices.
Included are also some clean ups and fixes for various minor issues.
Signed-off-by: Johan Hovold <johan@kernel.org>
-----BEGIN PGP SIGNATURE-----
iQIuBAABCAAYBQJYQARNERxqb2hhbkBrZXJuZWwub3JnAAoJEEEN5E/e4bSVPxIP
/i7OTbUIXqh0J/CMUAwRkCK4zrrXhwHCG77uReAiuiFhglR/wAMbPimumV7Daker
S14XFtyhi7oFBu1A9LkFFI2CTuaOFLnnrYc9Bqxfw8vKnCVMBOfqW7hasumkKY1g
XWF/IBNQZR3OWqePTefbTgZNXXKe2MMn02XAdswsaxSHXca95eLSu623Rp869H6o
voJDzj7RLBJCqLSH/IA0MZcdjcQphEVlpFV5wOfx2+4nvhSBQynLPeH79581eUM2
WsM0lVH9d04AuP5s1CN17cPezBL/cA1dnYThwDXMOC8MI+5resLXP7TalsK5e7pr
2qezrAiD9bwvqM+8nrEz46qpFLBbT+kM7qmlrHc9QNqm0XLtCdGy268z+omYLGuP
1cLA/IOFvn9t/o4NiN9+XgQM90MEBSaKdzsdXuIKgHIlHhT057b6K6Kw7oF4kBmO
S3soInK3edIFnaDEOOvp9UANEw/R6bPjmSMAgQsOZcd1T5OI+WNBhM9kBy/w8XfY
wLfBLMguoQJbK/06JcKZHL/RDC1VTIjHmUE0ZSu+kjXKweRQJVeYo84438W5QENI
c2MBxG/7hC+J40LYfWEHUg/HaPVomJV0qRdhx16JtMghXxUBPk1qQqBrlT28CsXh
N1EqwiK4dn+Jmi7XxoKTk8QFeAn0EQOI4obeNFIy7kNd
=FChe
-----END PGP SIGNATURE-----
Merge tag 'usb-serial-4.10-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/johan/usb-serial into usb-next
Johan writes:
USB-serial updates for v4.10-rc1
These updates include a new driver for Fintek F8153x devices, support
for the GPIO functionality on CP2105 devices, and improved support for
CH34X devices.
Included are also some clean ups and fixes for various minor issues.
Signed-off-by: Johan Hovold <johan@kernel.org>
Function klsi_105_open() calls usb_control_msg() (to "enable read") and
checks its return value. When the return value is unexpected, it only
assigns the error code to the return variable retval, but does not
terminate the exception path. This patch fixes the bug by inserting
"goto err_generic_close;" when the call to usb_control_msg() fails.
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Signed-off-by: Pan Bian <bianpan2016@163.com>
[johan: rebase on prerequisite fix and amend commit message]
Signed-off-by: Johan Hovold <johan@kernel.org>
Kill urbs and disable read before returning from open on failure to
retrieve the line state.
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
The comment says function wa_nep_queue() should return 0 if ok, and <0
errno code on error. However, its implementation always returns 0, even
if the call to kzalloc() fails. As a result, the return value may be
inconsistent with the execution status, which may mislead the callers.
This patch fixes the bug, returning -ENOMEM when the call to kzalloc()
fails.
Signed-off-by: Pan Bian <bianpan2016@163.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In function __wa_xfer_setup_segs(), variable result takes the return
value. Its value should be a negative errno on failures. Because result
may be reassigned in a loop, and its value is guaranteed to be not less
than 0 during the following repeats of the loop. So when the call to
kmalloc() or usb_alloc_urb() fails in the loop, the value of variable
result may be 0 (indicates no error), which is inconsistent with the
execution status. This patch fixes the bug, initializing variable result
with -ENOMEM in the loop.
Signed-off-by: Pan Bian <bianpan2016@163.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In function wusb_dev_sec_add(), variable result takes the return value.
Its value should be negative on failures. When function krealloc() is
called, an earlier check of variable result guarantees that the value of
result must not be less than "sizeof(*secd)", and result is not
reassigned when krealloc() returns a NULL pointer. As a result, a
positive value may be returned, which makes it impossible for the caller
of wusb_dev_sec_add() to detect the error. This patch fixes the bug by
assigning -ENOMEM to result when krealloc() returns NULL.
Signed-off-by: Pan Bian <bianpan2016@163.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The ehci_w90x900_probe function is not doing anything other than
calling usb_w90x900_probe function so ehci_w90x900_probe function
is unuseful that is why removed ehci_w90x900_probe functions and
renamed usb_w90x900_probe function to ehci_w90x900_probe for proper
naming.
The ehci_w90x900_remove function is also not doing anything other
than calling usb_w90x900_remove that is why removed ehci_w90x900_remove
function and renamed usb_w90x900_remove to ehci_w90x900_remove for proper
naming.
This also removes warning of checkpatch.pl script.
Signed-off-by: Manjunath Goudar <csmanjuvijay@gmail.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: Wan ZongShun <mcuos.com@gmail.com>
Cc: linux-usb@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Adds the device tree bindings description for Samsung S3C2410 and
compatible USB OHCI controller.
Signed-off-by: Sergio Prado <sergio.prado@e-labworks.com>
Acked-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The da8xx ohci controller is not working after suspend and resume.
This is because only the root hub is being resumed.
Balance the ohci_suspend of the suspend path with an ohci_resume
in the resume path so that we resume the entire controller, and not
just the root hub.
Also, while we are here, remove setting device power_state,
as this is no longer needed and scheduled for removal
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Axel Haslam <ahaslam@baylibre.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This adds the compatible string to the ohci driver
to be able to probe from DT
Signed-off-by: Axel Haslam <ahaslam@baylibre.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch documents the device tree bindings required for
the ohci controller found in TI da8xx family of SoC's
Cc: robh+dt@kernel.org
Cc: mark.rutland@arm.com
Cc: devicetree@vger.kernel.org
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Axel Haslam <ahaslam@baylibre.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Using a regulator to handle VBUS will eliminate the need for
platform data and callbacks, and make the driver more generic
allowing different types of regulators to handle VBUS.
The regulator equivalents to the platform callbacks are:
set_power -> regulator_enable/regulator_disable
get_power -> regulator_is_enabled
get_oci -> regulator_get_error_flags
ocic_notify -> regulator event notification
Signed-off-by: Axel Haslam <ahaslam@baylibre.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
To migrate to a DT based boot, we will remove the use of platform
callbacks, in favor of using the regulator framework to handle
vbus and over current.
In preparation to use a regulator instead of callbacks, move the platform
data callbacks into separate functions. This provides well defined place
to for the regulator API to coexist with the platform callbacks before
all users are converted.
Signed-off-by: Axel Haslam <ahaslam@baylibre.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Instead of global variables, use the extra_priv_size of
the ohci driver.
We cannot yet move the ocic mask because this is used on
the interrupt handler which is registered through platform
data and does not have an hcd pointer. This will be moved
on a later patch.
Tested-by: David Lechner <david@lechnology.com>
Signed-off-by: Axel Haslam <ahaslam@baylibre.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
- Properly mark little endian descriptors for udc
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJYO4X5AAoJEEhZKYFQ1nG78yYH/A8GJ6a3pBwvgF3XUhZusp75
w1yg7TnP4aPXDFdS2dpS0buFrBji/0MxTZm3aKNKIHL2jF6ZRW5TvhapA9xv7ezY
BhJOMXMUQAQSG/hnnu8QBJcrd0de3+EUhK6jYKInhvtNQUWl1jW073VAudlp2u4L
lVeHg49+u/10KlZ1Y6yipOH/KzfrOM1oGYBwyl7KMA48R2EASJ0FATcwUM/tRUX3
n6suCg/Z0VVFRdeYkiJdgnjxIbI+QR6TPMV+MWT1O32EniWm3pQT4G3WODooVqO9
oLc+4xgMoPkoiN5XwkYRNZ3wqhDp7xk2v10XJ7zTP1Xrqt2YFBk8K+Ls2/eQmGU=
=uOYb
-----END PGP SIGNATURE-----
Merge tag 'usb-ci-v4.10-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/peter.chen/usb into usb-next
Peter writes:
- Adding ULPI PHY support for imx53
- Properly mark little endian descriptors for udc
Detailed description for this pull request:
- The extcon-usb-gpio driver supports the VBUS detection with USB ID and VBUS pin.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQIcBAABAgAGBQJYM9sEAAoJEJzN3yze689TCacP/0bLWyQBWgpTrcK42Yi8UeQs
oCBaR60yGjpemwPlpSMq9GhY+6OvKMyCXHNdaK/l4UOV4u9uCKmx50I44Udr8qcf
8hHqONBWb0gEZJ4bK/gYNV+zb2bqFZ/tWECimmAerugWKzqX3xRBj227rgayijNM
JKlx8Tqhcy+QY7W5pmawg+D4YR1fQ+KWB3XHqOIVH8a4n+ir5A0MYZXh4hfsgyEo
dEwhALldgCRZx5NirIdJnUyBKSQYPGczARCsPTYDFVLTElLs1arxS1MYDwFmDyYi
FzuUc8PR8xVNkS9vp8ElPS/kw5Mgc8ERj/4ReqK1WGsrM4UXvgCr6r1gPH6oD27i
6eYEBNRs+WClu7rvcoThG1VtMwJibufk6GA54tkrLvhM1U7NR3oZlrzGFm0j8oLQ
OHHaqBN5OZFVE6sxwJpCstfPHkjC0VMd1xS/kqAOeZTS9nb9f8k9x0Bm8rfQeISQ
5pU+7HV9cQU3ywF5Ur5dNlGu2/hi5S08uZ7ytKjdNt2HDjnyEb0KH9Ksoe7nghO8
MLk5+MOYCOjf23HLe7LZA4/a/OL55PVa2blTJV3Vnq/BfBDpW/6blajBwTwZmYyW
bz2TCM7Ku+J63LUueMT6lzbBqAP39J5TN3Fm4rQOZZG8dInMkNxaC+w52eMz6uzw
bS7fuDw0H+NbIrUv2nqG
=28kq
-----END PGP SIGNATURE-----
Merge tag 'extcon-next-for-4.10' of git://git.kernel.org/pub/scm/linux/kernel/git/chanwoo/extcon into usb-nextx
Chanwoo writes:
Update extcon for 4.10
Detailed description for this pull request:
- The extcon-usb-gpio driver supports the VBUS detection with USB ID and VBUS pin.
Merge contains:
*) Add new usb2 phy driver for Meson8b and GXBB
*) Remove phy drivers added for miphy365 and STiH415/6 (as support for
these SoCs are removed from the kernel)
*) Add a sysfs entry to facilitate usb role swap in rcar SoC
*) Add support for otg port in rk3399
*) misc fixes in various phy drivers and cleanups
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=jfKK
-----END PGP SIGNATURE-----
Merge tag 'phy-for-4.10' of git://git.kernel.org/pub/scm/linux/kernel/git/kishon/linux-phy into usb-next
Kishon writes:
phy: for 4.10
Merge contains:
*) Add new usb2 phy driver for Meson8b and GXBB
*) Remove phy drivers added for miphy365 and STiH415/6 (as support for
these SoCs are removed from the kernel)
*) Add a sysfs entry to facilitate usb role swap in rcar SoC
*) Add support for otg port in rk3399
*) misc fixes in various phy drivers and cleanups
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Pull IOMMU fixes from David Woodhouse:
"Two minor fixes.
The first fixes the assignment of SR-IOV virtual functions to the
correct IOMMU unit, and the second fixes the excessively large (and
physically contiguous) PASID tables used with SVM"
* git://git.infradead.org/intel-iommu:
iommu/vt-d: Fix PASID table allocation
iommu/vt-d: Fix IOMMU lookup for SR-IOV Virtual Functions
Pull MIPS fixes from Ralf Baechle:
"Another round of MIPS fixes for 4.9:
- Fix unreadable output in __do_page_fault due to the KERN_CONT
patchset
- Correctly handle MIPS R6 fixes to the c0_wired register"
* 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus:
MIPS: mm: Fix output of __do_page_fault
MIPS: Mask out limit field when calculating wired entry count
Botched calculation of number of pages. As the result,
we were dropping pieces when doing splice to pipe from
e.g. 9p.
Reported-by: Alexei Starovoitov <ast@kernel.org>
Tested-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Pull i2c fixes from Wolfram Sang:
"Here is a revert and two bugfixes for the I2C designware driver.
Please note that we are still hunting down a regression for the
i2c-octeon driver. While there is a fix pending, we have unclear
feedback from the testers currently. An rc8 would be quite helpful
for this case"
* 'i2c/for-current' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux:
Revert "i2c: designware: do not disable adapter after transfer"
i2c: designware: fix rx fifo depth tracking
i2c: designware: report short transfers
Pull ARM fix from Russell King:
"This resolves the ksyms issues by reverting the commit which
introduced the breakage"
There was what I consider to be a better fix, but it's late in the rc
game, so I'll take the revert.
* 'fixes' of git://git.armlinux.org.uk/~rmk/linux-arm:
Revert "arm: move exports to definitions"
Pull networking fixes from David Miller:
1) Fix leak in fsl/fman driver, from Dan Carpenter.
2) Call flow dissector initcall earlier than any networking driver can
register and start to use it, from Eric Dumazet.
3) Some dup header fixes from Geliang Tang.
4) TIPC link monitoring compat fix from Jon Paul Maloy.
5) Link changes require EEE re-negotiation in bcm_sf2 driver, from
Florian Fainelli.
6) Fix bogus handle ID passed into tfilter_notify_chain(), from Roman
Mashak.
7) Fix dump size calculation in rtnl_calcit(), from Zhang Shengju.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (26 commits)
tipc: resolve connection flow control compatibility problem
mvpp2: use correct size for memset
net/mlx5: drop duplicate header delay.h
net: ieee802154: drop duplicate header delay.h
ibmvnic: drop duplicate header seq_file.h
fsl/fman: fix a leak in tgec_free()
net: ethtool: don't require CAP_NET_ADMIN for ETHTOOL_GLINKSETTINGS
tipc: improve sanity check for received domain records
tipc: fix compatibility bug in link monitoring
net: ethernet: mvneta: Remove IFF_UNICAST_FLT which is not implemented
dwc_eth_qos: drop duplicate headers
net sched filters: fix filter handle ID in tfilter_notify_chain()
net: dsa: bcm_sf2: Ensure we re-negotiate EEE during after link change
bnxt: do not busy-poll when link is down
udplite: call proper backlog handlers
ipv6: bump genid when the IFA_F_TENTATIVE flag is clear
net/mlx4_en: Free netdev resources under state lock
net: revert "net: l2tp: Treat NET_XMIT_CN as success in l2tp_eth_dev_xmit"
rtnetlink: fix the wrong minimal dump size getting from rtnl_calcit()
bnxt_en: Fix a VXLAN vs GENEVE issue
...
Pull libnvdimm fixes from Dan Williams:
- Fix a crash that occurs at driver initialization if the memory region
is already busy (request_mem_region() fails).
- Fix a vma validation check that mistakenly allows a private device-
dax mapping to be established. Device-dax explicitly forbids private
mappings so it can guarantee a given fault granularity and backing
memory type.
Both of these fixes have soaked in -next and are tagged for -stable.
* 'libnvdimm-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/nvdimm/nvdimm:
device-dax: fail all private mapping attempts
device-dax: check devm_nsio_enable() return value
Four fixes for bugs found by syzkaller on x86, all for stable.
-----BEGIN PGP SIGNATURE-----
iQEcBAABCAAGBQJYObr8AAoJEED/6hsPKofocbIH/j3p7QB73rDM2OCBhzTgGoOb
hcMLXnYEBD5C48ym2QW+wTEWJNNBikKOknYDX8wD1fIsaf8QoMqjEOSyxLPlexWI
mfTZnRAqSqYY9sPdlexpGAQV1uusCoIf2q9A+kW9Yy5q9ngzimiimRtFXgb/u6o5
mXZc7WcM8ZYSYdS+0Bz1lL6k1MGt1Yn207tQ3QNdWi4Pn6aWZp3+8C7rLjWu5zq8
LkMRsgedyxjULnyXedF+/IaXlC7qVO2LVwdxuHWsmeAPp/GmrNbAD+/4JKNk/Sgz
DPcPOWB/cCcCbWVY/8k+gRm0mnknX4bqYnwHwju++gwiUmJXIg3vWKfCDUw2SN0=
=MnV8
-----END PGP SIGNATURE-----
Merge tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm
Pull KVM fixes from Radim Krčmář:
"Four fixes for bugs found by syzkaller on x86, all for stable"
* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm:
KVM: x86: check for pic and ioapic presence before use
KVM: x86: fix out-of-bounds accesses of rtc_eoi map
KVM: x86: drop error recovery in em_jmp_far and em_ret_far
KVM: x86: fix out-of-bounds access in lapic
Fixes marked for stable:
- Set missing wakeup bit in LPCR on POWER9 (Benjamin Herrenschmidt)
- Fix the early OPAL console wrappers (Oliver O'Halloran)
- Fixup kernel read only mapping (Aneesh Kumar K.V)
Fixes for code merged this cycle:
- Fix missing CRCs, add more asm-prototypes.h declarations (Nicholas Piggin)
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=75sc
-----END PGP SIGNATURE-----
Merge tag 'powerpc-4.9-6' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux
Pull powerpc fixes from Michael Ellerman:
"Fixes marked for stable:
- Set missing wakeup bit in LPCR on POWER9
- Fix the early OPAL console wrappers
- Fixup kernel read only mapping
Fixes for code merged this cycle:
- Fix missing CRCs, add more asm-prototypes.h declarations"
* tag 'powerpc-4.9-6' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux:
powerpc/mm: Fixup kernel read only mapping
powerpc/boot: Fix the early OPAL console wrappers
powerpc: Fix missing CRCs, add more asm-prototypes.h declarations
powerpc: Set missing wakeup bit in LPCR on POWER9
In commit 10724cc7bb ("tipc: redesign connection-level flow control")
we replaced the previous message based flow control with one based on
1k blocks. In order to ensure backwards compatibility the mechanism
falls back to using message as base unit when it senses that the peer
doesn't support the new algorithm. The default flow control window,
i.e., how many units can be sent before the sender blocks and waits
for an acknowledge (aka advertisement) is 512. This was tested against
the previous version, which uses an acknowledge frequency of on ack per
256 received message, and found to work fine.
However, we missed the fact that versions older than Linux 3.15 use an
acknowledge frequency of 512, which is exactly the limit where a 4.6+
sender will stop and wait for acknowledge. This would also work fine if
it weren't for the fact that if the first sent message on a 4.6+ server
side is an empty SYNACK, this one is also is counted as a sent message,
while it is not counted as a received message on a legacy 3.15-receiver.
This leads to the sender always being one step ahead of the receiver, a
scenario causing the sender to block after 512 sent messages, while the
receiver only has registered 511 read messages. Hence, the legacy
receiver is not trigged to send an acknowledge, with a permanently
blocked sender as result.
We solve this deadlock by simply allowing the sender to send one more
message before it blocks, i.e., by a making minimal change to the
condition used for determining connection congestion.
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
gcc-7 detects a short memset in mvpp2, introduced in the original
merge of the driver:
drivers/net/ethernet/marvell/mvpp2.c: In function 'mvpp2_cls_init':
drivers/net/ethernet/marvell/mvpp2.c:3296:2: error: 'memset' used with length equal to number of elements without multiplication by element size [-Werror=memset-elt-size]
The result seems to be that we write uninitialized data into the
flow table registers, although we did not get any warning about
that uninitialized data usage.
Using sizeof() lets us initialize then entire array instead.
Fixes: 3f518509de ("ethernet: Add new driver for Marvell Armada 375 network unit")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Drop duplicate header delay.h from mlx5/core/main.c.
Signed-off-by: Geliang Tang <geliangtang@gmail.com>
Acked-by: Matan Barak <matanb@mellanox.com>
Acked-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Drop duplicate header delay.h from adf7242.c.
Signed-off-by: Geliang Tang <geliangtang@gmail.com>
Acked-by: Stefan Schmidt <stefan@osg.samsung.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Drop duplicate header seq_file.h from ibmvnic.c.
Signed-off-by: Geliang Tang <geliangtang@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We set "tgec->cfg" to NULL before passing it to kfree(). There is no
need to set it to NULL at all. Let's just delete it.
Fixes: 57ba4c9b56 ("fsl/fman: Add FMan MAC support")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ETHTOOL_GLINKSETTINGS command is deprecating the ETHTOOL_GSET
command and likewise it shouldn't require the CAP_NET_ADMIN capability.
Signed-off-by: Miroslav Lichvar <mlichvar@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In commit 35c55c9877 ("tipc: add neighbor monitoring framework") we
added a data area to the link monitor STATE messages under the
assumption that previous versions did not use any such data area.
For versions older than Linux 4.3 this assumption is not correct. In
those version, all STATE messages sent out from a node inadvertently
contain a 16 byte data area containing a string; -a leftover from
previous RESET messages which were using this during the setup phase.
This string serves no purpose in STATE messages, and should no be there.
Unfortunately, this data area is delivered to the link monitor
framework, where a sanity check catches that it is not a correct domain
record, and drops it. It also issues a rate limited warning about the
event.
Since such events occur much more frequently than anticipated, we now
choose to remove the warning in order to not fill the kernel log with
useless contents. We also make the sanity check stricter, to further
reduce the risk that such data is inavertently admitted.
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
commit 817298102b ("tipc: fix link priority propagation") introduced a
compatibility problem between TIPC versions newer than Linux 4.6 and
those older than Linux 4.4. In versions later than 4.4, link STATE
messages only contain a non-zero link priority value when the sender
wants the receiver to change its priority. This has the effect that the
receiver resets itself in order to apply the new priority. This works
well, and is consistent with the said commit.
However, in versions older than 4.4 a valid link priority is present in
all sent link STATE messages, leading to cyclic link establishment and
reset on the 4.6+ node.
We fix this by adding a test that the received value should not only
be valid, but also differ from the current value in order to cause the
receiving link endpoint to reset.
Reported-by: Amar Nv <amar.nv005@gmail.com>
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The mvneta driver advertises it supports IFF_UNICAST_FLT. However, it
actually does not. The hardware probably does support it, but there is
no code to configure the filter. As a quick and simple fix, remove the
flag. This will cause the core to fall back to promiscuous mode.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Fixes: b50b72de2f ("net: mvneta: enable features before registering the driver")
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull parisc fixes from Helge Deller:
"On parisc we were still seeing occasional random segmentation faults
and memory corruption on SMP machines. Dave Anglin then looked again
at the TLB related code and found two issues in the PCI DMA and
generic TLB flush functions.
Then, in our startup code we had some timing of the cache and TLB
functions to calculate a threshold when to use a complete TLB/cache
flush or just to flush a specific range. This code produced a race
with newly started CPUs and thus lead to occasional kernel crashes
(due to stale TLB/cache entries). The patch by Dave fixes this issue
by flushing the local caches before starting secondary CPUs and by
removing the race.
The last problem fixed by this series is that we quite often suffered
from hung tasks and self-detected stalls on the CPUs. It was somehow
clear that this was related to the (in v4.7) newly introduced cr16
clocksource and the own implementation of sched_clock(). I replaced
the open-coded sched_clock() function and switched to the generic
sched_clock() implementation which seems to have fixed this isse as
well.
All patches have been sucessfully tested on a variety of machines,
including our debian buildd servers.
All patches (beside the small pr_cont fix) are tagged for stable
releases"
* 'parisc-4.9-4' of git://git.kernel.org/pub/scm/linux/kernel/git/deller/parisc-linux:
parisc: Also flush data TLB in flush_icache_page_asm
parisc: Fix race in pci-dma.c
parisc: Switch to generic sched_clock implementation
parisc: Fix races in parisc_setup_cache_timing()
parisc: Fix printk continuations in system detection
Pull keys fixes from James Morris:
"From David:
- Fix mpi_powm()'s handling of a number with a zero exponent
[CVE-2016-8650].
Integrate my and Andrey's patches for mpi_powm() and use
mpi_resize() instead of RESIZE_IF_NEEDED() - the latter adds a
duplicate check into the execution path of a trivial case we
don't normally expect to be taken.
- Fix double free in X.509 error handling"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jmorris/linux-security:
mpi: Fix NULL ptr dereference in mpi_powm() [ver #3]
X.509: Fix double free in x509_cert_parse() [ver #3]
CONFIG_MODVERSIONS has been broken for pretty much the whole 4.9 series,
and quite frankly, nobody has cared very deeply. We absolutely know how
to fix it, and it's not _complicated_, but it's not exactly pretty
either.
This oneliner fixes it without the ugliness, and allows for further
future cleanups.
"We've secretly replaced their regular MODVERSIONS with nothing at
all, let's see if they notice"
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
- Revert the recent commit that caused the ACPI _PTS method to
be executed in the power-off/reboot code path (as per the
specification) in an attempt to improve things on some systems
(apparently expecting _PTS to be executed in that code path),
but broke power-off/reboot on at least one other machine (Rafael
Wysocki).
- Fix kernel builds with the new WDAT watchdog driver enabled in
some configurations by explicitly selecting WATCHDOG_CORE when
enabling the WDAT watchdog driver (Mika Westerberg).
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=q/vx
-----END PGP SIGNATURE-----
Merge tag 'acpi-4.9-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull ACPI fixes from Rafael Wysocki:
"Two ACPI fixes for 4.9-rc7.
One of them reverts a recent ACPI commit that attempted to improve
reboot/power-off on some systems, but introduced problems elsewhere,
and the other one fixes kernel builds with the new WDAT watchdog
driver enabled in some configurations.
Specifics:
- Revert the recent commit that caused the ACPI _PTS method to be
executed in the power-off/reboot code path (as per the
specification) in an attempt to improve things on some systems
(apparently expecting _PTS to be executed in that code path), but
broke power-off/reboot on at least one other machine (Rafael
Wysocki).
- Fix kernel builds with the new WDAT watchdog driver enabled in some
configurations by explicitly selecting WATCHDOG_CORE when enabling
the WDAT watchdog driver (Mika Westerberg)"
* tag 'acpi-4.9-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
watchdog: wdat_wdt: Select WATCHDOG_CORE
Revert "ACPI: Execute _PTS before system reboot"
Following the kernel Bugzilla discussion during the Kernel Summit
(https://lwn.net/Articles/705245/), add bug tracking system location
entry type (B) to MAINTAINERS and populate it for several subsystems
known to be using the kernel BZ actively (and add the upstream BZ for
ACPICA too).
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This reverts commit 0317e6c0f1.
Srinivas reported recently touchscreen and touchpad stopped working in
Haswell based machine in Linux 4.9-rc series with timeout errors from
i2c_designware:
[ 16.508013] i2c_designware INT33C3:00: controller timed out
[ 16.508302] i2c_hid i2c-MSFT0001:02: failed to change power setting.
[ 17.532016] i2c_designware INT33C3:00: controller timed out
[ 18.556022] i2c_designware INT33C3:00: controller timed out
[ 18.556315] i2c_hid i2c-ATML1000:00: failed to retrieve report from device.
I managed to reproduce similar errors on another Haswell based machine
where touchscreen initialization fails maybe in every 1/5 - 1/2 boots.
Since root cause for these errors is not clear yet and debugging is
ongoing it's better to revert this commit as we are near to release.
Reported-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Guenter Roeck